Голосовая связь : Передача факсов/работа модема по IP-сети

Отправка факса OnRamp T.37

20 октября 2016 - Машинный перевод
Другие версии: PDF-версия:pdf | Английский (22 августа 2015) | Отзыв


Содержание


Введение

Этот раздел основного документа Store и Forward Fax T.37 FAX over IP описывает отправляющее факсом хранение и пересылку OnRamp. OnRamp T.37 является процессом принятия факса - вызова, кодирования того факса в Теговый формат файлов изображения (TIFF) (TIFF) и передачи того TIFF к почтовому серверу как прикрепление.

Этот документ содержит конфигурацию, требуемую получить в рабочем состоянии функцию. Раздел Устранения неполадок пробегается через полезные команды отладки и как интерпретировать их значение. Используемую топологию показывают в разделе Диаграммы сети.

Предварительные условия

Требования

Определенные требования для этого документа заданы в основном разделе, Store и Forward Fax T.37 FAX over IP.

Используемые компоненты

Настоящий документ не имеет жесткой привязки к каким-либо конкретным версиям программного обеспечения и оборудования.

Сведения, представленные в этом документе, были получены от устройств, работающих в специальной лабораторной среде. Все устройства, описанные в этом документе, были запущены с чистой (стандартной) конфигурацией. В рабочей сети необходимо изучить потенциальное воздействие всех команд до их использования.

Условные обозначения

Дополнительные сведения об условных обозначениях см. в документе Технические рекомендации Cisco. Условные обозначения.

!--- конфигурацию

В разделах ниже, сначала Cisco объяснены параметры Конфигурации ПО IOS�, относящиеся к конфигурации факса OnRamp, и затем 5300 конфигураций отображены с дальнейшими примечаниями, разъяснив функции важных команд. Некоторые параметры произвольной конфигурации могут быть найдены в разделе, который придерживается 5300 конфигураций.

Схема сети

В данном документе используется сетевая установка, показанная на следующей схеме.

/image/gif/paws/47763/onramp_faxing1.gif

Параметры конфигурации

Обязательные параметры:
fax interface-type fax-mail Добавляет функциональность T.37 для шлюза. Требует перезагрузки на этих 5300, но не 5350 или 5400.
mta send server Это - имя хоста или IP-адрес сервера Протокола SMTP, к которому переходит маршрутизатор, посылают электронное письмо OnRamp через. Без этой конфигурации маршрутизатор не знает, где послать электронное письмо OnRamp. Посмотрите, что Никакой сервер не настроил раздел для отладок и консольных сообщений без настроенного сервера.
mta send postmaster Если mta, передаваемые почту - от опций, не оценивают или не настроены, этот адрес используется. Это размещено в Поле "From" электронной почты OnRamp. Если имя пользователя mta send mail-from и имя хоста mta send mail-from присутствуют, это является дополнительным. Щелкните здесь для отладки mspi для неудачного вызова.
ip domain name Используемый для определения почтового отправителя в Приветственном сообщении с именем хоста. имя домена. Маршрутизатор должен быть повторно загружен после того, как эта команда настроена.
onramp call application voice flash:app_libretto_onramp.2.0.1.1.tcl Определяет глобальное название для приложения (onramp, в этом случае) и его местоположение (во флэш-памяти маршрутизатора, в этом случае).
dial-peer voice 8913180 приложений обычной телефонной сети в режиме OnRamp Приложение OnRamp вызовов, когда совпадают с этой точкой вызова.
приложение mmoip dial-peer voice 1 fax_on_vfc_onramp_app исходящий Приложение, которое вызовут, когда эта Мультимедийная почта поверх IP (MMoIP) совпадают с узлом. Предварительно связанный в программном обеспечении Cisco IOS. Видимый через сводку show call application voice.
Необязательные параметры:
имя хоста mta send mail-from Это - имя хоста, которое будет использоваться в Поле "From" на электронной почте OnRamp. Обязательный, если не присутствует команда mta send postmaster. Если имя пользователя mta send mail-from используется, должен быть настроен.
mta send mail-from username Это - инициатор, чтобы использоваться в Поле "From" на электронной почте OnRamp. Используемый в сочетании с именем хоста mta send mail-from для получения всего Поля "From" — т.е. username@hostname. Обязательный, если не присутствует команда mta send postmaster. Если имя хоста mta send mail-from используется, должен быть настроен.
mta send subject Текстовая строка, которая будет использоваться в Поле Тема на электронной почте OnRamp.
mta передают with-subject
  • Добавляет номер вызывающего абонента с $s$ ключевого слова.
  • Добавляет номер вызываемого абонента с $d$ ключевого слова.
  • Добавляет и вызов и номер вызываемого абонента с ключевым словом оба.
Для показа отладки щелкнуть здесь.
mta send return-receipt-to Ключевые слова являются именем пользователя и именем хоста. Вместе они формируются disposition-notification-to:username@hostname.
mdn mmoip номера dial-peer voice Запрашивает, чтобы электронное письмо, передаваемое через этот MMoIP запросы от равноправного участника уведомление о размещении сообщения (MDN), было послано desitnation definted командой mta send return-receipt-to.
dsn mmoip номера dial-peer voice {задерживается | успех | сбой} Запрашивает, чтобы предупреждение статуса доставки (DSN) было передано назначению, определенному командой mta send mail-from

Конфигурация OnRamp

vdtl-5300-7a# show running-config 
Building configuration...

Current configuration : 2294 bytes
!
! Last configuration change at 10:49:16 EST Mon Mar 18 2003
! NVRAM config last updated at 11:00:42 EST Mon Mar 4 2003
!
version 12.2
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
no service password-encryption
!
hostname vdtl-5300-7a
!
!
resource-pool disable
clock timezone EST -5
!
ip subnet-zero
ip domain-name testlab-t37.com

!--- The ip domain-name command is needed so the router sends a fully qualified
!--- domain-name (FQDN) to the email server.
  

!--- Router must be reloaded after ip domain-name configuration due to a known bug
!--- that has since been resolved.

ip name-server 172.18.106.36

!--- The ip name-server command is required in order to do name resolution.

!
!
isdn switch-type primary-5ess
!
fax receive called-subscriber 8913180
fax interface-type fax-mail
! 
mta send server testlab-smtp.testlab-t37.com port 25

!--- The mta send server command identifies the email server for OnRamp emails.
 
! 
mta send subject Fax from On-Ramp GW vdlt-5300-7a
mta send with-subject both
mta send postmaster administrator@testlab-t37.com
!

!--- The address set with mta send postmaster is used as the "From" address
!--- unless mta send mail-from commands are defined.
 
! 
mta send mail-from hostname vdtl-5300-7a.testlab-t37.com
mta send mail-from username $s$
mta send return-receipt-to hostname testlab-t37.com
mta send return-receipt-to username admin
mta receive maximum-recipients 0
call-history-mib retain-timer 500
!
controller T1 0
framing esf
clock source line primary
linecode b8zs
pri-group timeslots 1-24
!
!
!
interface Ethernet0
ip address 15.80.7.11 255.255.255.0
!
interface Serial0:23
no ip address
isdn switch-type primary-5ess
isdn incoming-voice modem
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 15.80.7.1
no ip http server
ip pim bidir-enable
!
call rsvp-sync
!
call application voice onramp flash:app_libretto_onramp.2.0.1.1.tcl

!--- This identifies the call application to use. It is named "onramp" in
!--- this example.

voice-port 0:D 
!
mgcp profile default
!
dial-peer voice 1 mmoip
application fax_on_vfc_onramp_app out-bound
destination-pattern 8913144
information-type fax
session target mailto:$d$@testlab-t37.com 
!

!--- The MMoIP peers contain configuration specific to the called party number.
!--- It requests MDN and DSN. It identifies the application to use for the outbound
!--- call leg and specifies the address to which the email will be sent.
 
mdn
dsn success
dsn failure
! 
dial-peer voice 891314 pots
application onramp
incoming called-number 891314[4-5]
direct-inward-dial
port 0:D

!--- The pots peers for T.37 are no different than for voice calls with the exception of
!--- using the application defined above in the call application global configuration
!--- command. The direct-inward-dial command is required unless using a redialer.

!
line con 0
exec-timeout 0 0
line aux 0
line vty 0 4
login
!
ntp clock-period 17179806
ntp server 172.18.106.15
end

vdtl-5300-7a#

Необязательная конфигурация

Вот некоторые параметры произвольной конфигурации. Первый пример показывает вам, как настроить множественные почтовые ящики с помощью традиционных адресов электронной почты, и второй пример показывает вам, как настроить множественные почтовые ящики с помощью номеров вызываемого абонента для адресов электронной почты.

Пример 1:

!
dial-peer voice 1 mmoip
 application fax_on_vfc_onramp_app out-bound
 destination-pattern 8913144
 information-type fax
 session target mailto:andy@testlab-t37.com
!
dial-peer voice 2 mmoip
 application fax_on_vfc_onramp_app out-bound
 destination-pattern 8913145
 information-type fax
 session target mailto:bobby@testlab-t37.com
!
dial-peer voice 891314 pots
 application onramp
 incoming called-number 891314[4-5]
 direct-inward-dial
 port 0:D
!
В этой конфигурации PRI имеет два номера Direct Inward Dialing (DID): 891-3144 и 891-3145. В зависимости от которого набран номер, электронное письмо послано или andy@testlab-t37.com или bobby@testlab-t37.com.

Пример 2:

!
dial-peer voice 1 mmoip
application fax_on_vfc_onramp_app out-bound
destination-pattern 8913144
information-type fax
session target mailto:$d$@testlab-t37.com
!
С этой конфигурацией Сервис идентификации набранного номера (DNIS) (номер вызываемого абонента) вставлен в RCPT в: команда SMTP. Это позволяет клиентам давать каждому пользователю DID для приложений OnRamp. Они просто добавляют псевдоним на почтовом сервере. 12 марта 15:42:12.947: (C) S: RCPT к: <FAX=8913144@testlab-t37.com>

Примечание: Удостоверьтесь, что псевдоним электронной почты является FAX=8913144@domain.com вместо 8913144@domain.com, или электронная почта не будет отправлена должным образом.

Устранение неполадок

Отказавшие отладки

Примечание: На изменения конфигурации обращают внимание выше отладок.

debug mspi send
!
fax interface-type fax-mail
mta send server testlab-smtp.testlab-t37.com port 25
mta send mail-from hostname whatever.com
mta receive maximum-recipients 0
call-history-mib retain-timer 500
! 

Примечание: Команда mta send mail-from username опущена от конфигурации, как команда mta send postmaster.

vdtl-5300-7a#
Mar 4 10:03:29.165: mspi_setup_req: for cid=0x27
Mar 4 10:03:29.165: envelope_from=FAX=@        
!--- Note: This is not a valid email address (no domain).

Mar 4 10:03:29.165: envelope_to=andy@testlab-t37.com
Mar 4 10:03:30.165: mspi_chk_connect: cid=0x27, cnt=0, 
Mar 4 10:03:30.165: SMTP connected to the server !  
!--- The connection to the SMTP server is initiated.

Mar 4 10:03:30.165: mspi_bridge: cid=0x27, dst cid=0x28,
Mar 4 10:03:56.985: mspi_xmit: cid=0x27, st=CONFERENCED, src_cid=0x28, buf cnt=0
Mar 4 10:03:56.985: %MSPI-4-MSPI_NO_SMTP_SEND: MSPI- Could not
 send data to the SMTP server, cid=39, mspi_on_xmit, lost connection
Mar 4 10:03:56.985: mspi_on_xmit: cid=0x27, lost connection
Mar 4 10:03:56.985: disc text=no route to destination (3): SMTP client engine
 lost connection  
!--- The statement "no route to destination" is a little misleading as a cause code.

Mar 4 10:03:56.985: mspi_xmit: cid=0x27, st=ABORTING, src_cid=0x28
Mar 4 10:03:56.985: discarding buffer

!--- Several lines of mspi_xmit debugs that were identical to the lines above
!--- and below this note have been suppressed.

Mar 4 10:03:56.989: mspi_xmit: cid=0x27, st=ABORTING, src_cid=0x28
Mar 4 10:03:56.993: discarding buffer
Mar 4 10:03:56.993: %LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT: ESMTP client
 did not connect or lost connection to remote server
Mar 4 10:03:56.993: mspi_bridge_drop: cid=0x27, dst cid=0x28, st=ABORTING, onramp
Mar 4 10:03:56.993: mspi_disconnect: cid=0x27, st=DISCONNECTING, cause=no route to
 destination (3)
Mar 4 10:03:56.993: mspi_on_call_hist: cid=0x27, cause=no route to destination (3):
 SMTP client engine lost connection
Mar 4 10:03:56.993: disposing smtp ctx
Mar 4 10:03:56.993: mspi_free_ccb: mmccb allocated=1, inserted=0
vdtl-5300-7a#

Та же проблема может быть замечена немного более ясная с этой отладкой:

vdtl-5300-7a# debug mta send all
Mar 5 16:48:46.420: esmtp_client_engine_open: from=FAX=@, to=andy@testlab-t37.com
Mar 5 16:48:46.420: esmtp_client_engine_add_headers: from_comment=Fax 
Mar 5 16:48:46.792: esmtp_client_work: socket 0 attempting to connect to IP
 address 172.18.106.36
Mar 5 16:48:46.792: esmtp_client_work: socket 0 readable for first time
Mar 5 16:48:46.792: esmtp_client_work: socket 0 readable for first time
Mar 5 16:48:46.796: (C)R: 220 testlab-smtp.testlab-t37.com Microsoft ESMTP MAIL Service,
 Version: 5.0.2195.4453 ready at Tue, 5 Mar 2002 16:48:12 -0500 
!--- This is the SMTP server information displayed with the login.

Mar 5 16:48:46.796: (C)S: EHLO vdtl-5300-7a.testlab-t37.com
Mar 5 16:48:47.208: (C)R: 250-testlab-smtp.testlab-t37.com Hello [15.80.7.11]

!--- All the responses through the R: 250 OK are in response to the EHLO command from
!--- the sender (the 5300). These are the capabilities of the receiver.

Mar 5 16:48:47.208: (C)R: 250-TURN
Mar 5 16:48:47.208: (C)R: 250-ATRN 
Mar 5 16:48:47.208: (C)R: 250-SIZE
Mar 5 16:48:47.208: (C)R: 250-ETRN 
Mar 5 16:48:47.212: (C)R: 250-PIPELINING
Mar 5 16:48:47.212: (C)R: 250-DSN
Mar 5 16:48:47.212: (C)R: 250-ENHANCEDSTATUSCODES
Mar 5 16:48:47.212: (C)R: 250-8bitmime                                                          
Mar 5 16:48:47.212: (C)R: 250-BINARYMIME                                              
Mar 5 16:48:47.212: (C)R: 250-CHUNKING                                                             
Mar 5 16:48:47.212: (C)R: 250-VRFY                                                             
Mar 5 16:48:47.212: (C)R: 250-X-EXPS GSSAPI NTLM LOGIN                   
Mar 5 16:48:47.212: (C)R: 250-X-EXPS=LOGIN                                            
Mar 5 16:48:47.212: (C)R: 250-AUTH GSSAPI NTLM LOGIN                      
Mar 5 16:48:47.212: (C)R: 250-AUTH=LOGIN                                              
Mar 5 16:48:47.212: (C)R: 250-X-LINK2STATE                                           
Mar 5 16:48:47.212: (C)R: 250-XEXCH50                                                     
Mar 5 16:48:47.212: (C)R: 250 OK                                                                 
Mar 5 16:48:47.212: (C)S: MAIL FROM:<FAX=@>                                    
!--- This is the mail from command.

Mar 5 16:48:47.708: (C)R: 501 5.5.4 Invalid Address                                    
!--- The server does not like the address.

Mar 5 16:48:47.708: esmtp_client_work: error in response to MAIL FROM  
!--- This tells exactly where the problem ocurred in the SMTP exchange.

Mar 5 16:48:47.708: esmtp_client_work: ERROR, socket=0
Mar 5 16:49:15.132: %MSPI-4-MSPI_NO_SMTP_SEND: MSPI- Could not
send data to the SMTP server, cid=96, mspi_on_xmit, lost connection
Mar 5 16:49:15.132: %LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT: ESMTP client did not
 connect or lost connection to remote server
Mar 5 16:49:15.208: esmtp_client_work: Freeing ctx=0x62616C4C
Mar 5 16:49:15.208: esmtp_client: returned from work, context freed

Никакой сервер не настроен

fax receive called-subscriber 8913180
fax interface-type fax-mail
mta send subject Fax from On-Ramp GW vdlt-5300-7a
mta send postmaster administrator@testlab-t37.com
mta send mail-from hostname vdtl-5300-7a.testlab-t37.com
mta send mail-from username $s$
mta receive maximum-recipients 0

vdtl-5300-7a#
Mar 4 10:46:48.703: mspi_setup_req: for cid=0x3F
Mar 4 10:46:48.703: %MSPI-1-MSPI_BAD_CONFIG: MSPI-bad configuration, mspi_setup_req:
 NULL server ip address
Mar 4 10:46:48.703: mspi_setup_req: NULL server address
Mar 4 10:46:48.703: %LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT: ESMTP client
 did not connect or lost connection to remote server
vdtl-5300-7a# 

Настроенный сервер, но никакой IP-маршрут к серверу существует

vdtl-5300-7a# debug mspi send 
Mail SPI send debugging is on
vdtl-5300-7a#
Mar 20 09:35:27.126: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 20 09:35:29.306: mspi_setup_req: for cid=0x141
Mar 20 09:35:29.306: envelope_from=FAX=8915510@vdtl-5300-7a.testlab-t37.com
Mar 20 09:35:29.310: envelope_to=FAX=8913144@testlab-t37.com
Mar 20 09:35:30.310: mspi_chk_connect: cid=0x141, cnt=0, 
Mar 20 09:35:30.310: SMTP is in the error state...
Mar 20 09:35:30.310: disc text=no route to destination (3): SMTP client open failed
Mar 20 09:35:30.310: Still waiting for the SMTP connection.....  
!--- You can tell that the SMTP connection was never established.

Mar 20 09:35:30.310: %LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT: ESMTP client
 did not connect or lost connection to remote server
Mar 20 09:35:30.310: mspi_disconnect: cid=0x141, st=DISCONNECTING, cause=no route
 to destination (3)  
!--- This cause code seems to be an accurate description of the problem.

Mar 20 09:35:30.310: mspi_on_call_hist: cid=0x141, cause=no route to destination (3):
 SMTP client open failed
Mar 20 09:35:30.310: disposing smtp ctx
Mar 20 09:35:30.310: mspi_free_ccb: mmccb allocated=1, inserted=0
Mar 20 09:35:36.006: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510,
 call lasted 14 seconds
vdtl-5300-7a#

Примечание: Маршрутизатор не передает Полное доменное имя (FQDN) к Серверу Exchange MS, и этому не нравится синтаксис. Это вызвано тем, что маршрутизатор требует повторной загрузки после добавляющего "домена ip domain name "

vdtl-5300-7a# debug mmoip send email andy@testlab-t37.com
vdtl-5300-7a#
Mar 28 09:55:16.768: %SYS-5-CONFIG_I: Configured from console by console
Mar 28 09:55:17.936: esmtp_client_engine_open: from=testing@vdtl-5300-7a.testlab-t37.com,
 to=andy@testlab-t37.com
Mar 28 09:55:17.940: esmtp_client_engine_add_headers: from_comment=mspi Test User
Mar 28 09:55:18.072: esmtp_client_work: socket 0 attempting to connect to IP
 address 172.18.106.36
Mar 28 09:55:18.072: esmtp_client_work: socket 0 readable for first time
Mar 28 09:55:18.072: esmtp_client_work: socket 0 readable for first time
Mar 28 09:55:18.076: (C)R: 220 testlab-smtp.testlab-t37.com Microsoft ESMTP MAIL Service,
 Version: 5.0.2195.4453 ready at Thu, 28 Mar 2002 09:54:02 -0500 
Mar 28 09:55:18.076: (C)S: EHLO vdtl-5300-7a.  
!--- The Exchange server does not like the trailing dot (.).

Mar 28 09:55:18.484: (C)R: 501 5.5.4 Invalid Address
Mar 28 09:55:18.484: esmtp_client_work: EHLO failed; will try sending HELO
Mar 28 09:55:18.484: (C)S: HELO vdtl-5300-7a.
Mar 28 09:55:18.984: (C)R: 501 5.5.4 Invalid Address
Mar 28 09:55:18.984: esmtp_client_work: error in response to HELO
Mar 28 09:55:18.984: esmtp_client_work: ERROR, socket=0
Mar 28 09:55:18.984: esmtp_client_work: Freeing ctx=0x62661F18
Mar 28 09:55:18.988: esmtp_client: returned from work, context freed
vdtl-5300-7a#

Рабочие отладки

Эти команды отладки используются для стороны SMTP OnRamp:

vdtl-5300-7a# debug foip on-ramp 
FOIP On ramp faxmail debugging is on
vdtl-5300-7a#
Mar 18 10:57:50.995: lapp_on_application: Incoming Event: (15 = CC_EV_CALL_HANDOFF),
 CID(216), DISP(0)
Mar 18 10:57:50.995: lapp_on_call_handoff: Authentication enabled = FALSE
Mar 18 10:57:50.995: lapp_on_call_handoff: Authentication ID = 0
Mar 18 10:57:50.995: lapp_on_call_handoff: Authentication ID source = IVR or unknown
Mar 18 10:57:50.999: lapp_on_call_handoff: Authentication status = SUCCESS
Mar 18 10:57:50.999: lapp_on_call_handoff: Accounting enabled = FALSE
Mar 18 10:57:50.999: lapp_on_call_handoff: Accounting method list = fax
Mar 18 10:57:50.999: lapp_on_call_handoff: Mailto Address = 
Mar 18 10:57:50.999: lapp_on_conference_vtsp_fmsp: Begin conferencing VTSP and FMSP... 
Mar 18 10:57:50.999: lapp_on_change_state: old state(0) new state(1) 
!--- HANDOFF to VTSP_FMSP_CONFERENCING

Mar 18 10:57:51.003: lapp_on_application: Incoming Event: (29 = CC_EV_CONF_CREATE_DONE),
 CID(216), DISP(0)
Mar 18 10:57:51.003: lapp_on_application: Current call state = 1 
Mar 18 10:57:51.003: lapp_on_conference_created: The VTSP and the FMSP are conferenced
Mar 18 10:57:51.003: lapp_on_conference_created: Wait for FMSP call detail event
Mar 18 10:57:51.003: lapp_on_change_state: old state(1) new state(2) 
!--- VTSP_FMSP_CONFERENCING to FMSP_CALL_DETAIL

Mar 18 10:57:57.075: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 18 10:57:59.135: lapp_on_application: Incoming Event: (33 = CC_EV_FROM_FMSP_ON_CALL_DETAIL),
 CID(217), DISP(0)
Mar 18 10:57:59.139: lapp_on_application: Current call state = 2 
Mar 18 10:57:59.139: lapp_on_msp_event: Incoming call detail has arrived from the FMSP
Mar 18 10:57:59.139: lapp_on_setup_mspi: Prep MSPI ccCallSetupRequest... 
Mar 18 10:57:59.139: lapp_on_setup_mspi: Envelope from: FAX=8915510@vdtl-5300-7a.testlab-t37.com
Mar 18 10:57:59.139: lapp_on_setup_mspi: Envelope to: FAX=8913144@testlab-t37.com
Mar 18 10:57:59.139: lapp_on_setup_mspi: rfc822_to_comment: 8913144
Mar 18 10:57:59.139: lapp_on_setup_mspi: Faxmail subject: Fax from On-Ramp GW vdlt-5300-7a
[DNIS=8913144][ANI=8915510]
Mar 18 10:57:59.139: lapp_on_setup_mspi: Disposition notification to: admin@testlab-t37.com

!--- A read receipt is sent to admin@testlab-t37.com if the reader so chooses.

Mar 18 10:57:59.139: lapp_on_setup_mspi: Originator's TSI = rfc822_from_comment = Fax 
Mar 18 10:57:59.139: lapp_on_setup_mspi: Auth/Account ID = 0
Mar 18 10:57:59.139: lapp_on_setup_mspi: Do ccCallSetupRequest to MSPI
Mar 18 10:57:59.139: lapp_on_conference_fmsp_dmsp: Starting conference with FMSP and DMSP
Mar 18 10:57:59.139: lapp_on_conference_fmsp_dmsp: tiff file created = 2002:03:18 10:57:59
Mar 18 10:57:59.139: lapp_on_change_state: old state(2) new state(3)  
!--- FMSP_CALL_DETAIL to FMSP_DMSP_CONFERENCING

Mar 18 10:57:59.139: lapp_on_application: Incoming Event: (29 = CC_EV_CONF_CREATE_DONE),
 CID(217), DISP(0)
Mar 18 10:57:59.139: lapp_on_application: Current call state = 3 
Mar 18 10:57:59.139: lapp_on_conference_created: The FMSP and the DMSP are conferenced
Mar 18 10:57:59.139: lapp_on_conference_created: Sending
 CC_EV_TO_FMSP_ON_RECEIVE_ENABLE to FMSP
Mar 18 10:57:59.139: lapp_on_change_state: old state(3) new state(4)    
!--- FMSP_DMSP_CONFERENCING to FMSP_PAGE_ACCEPT_REQUESTED

Mar 18 10:58:00.139: lapp_on_application: Incoming Event: (8 = CC_EV_CALL_CONNECTED),
 CID(218), DISP(0)
Mar 18 10:58:00.139: lapp_on_application: Current call state = 4 
Mar 18 10:58:00.139: lapp_on_call_connected: Call connected event received.... - CID(218)
Mar 18 10:58:00.139: lapp_on_call_connected: MSPI call connected - CID(218)
Mar 18 10:58:00.139: lapp_on_call_connected: Start conferencing the DMSP and the MSPI
Mar 18 10:58:00.139: lapp_on_application: Incoming Event: (29 = CC_EV_CONF_CREATE_DONE),
 CID(219), DISP(0)
Mar 18 10:58:00.139: lapp_on_application: Current call state = 4 
Mar 18 10:58:11.539: lapp_on_application: Incoming Event:
 (36 = CC_EV_FROM_FMSP_ON_PAGE_ACCEPT_REQUESTED), CID(217), DISP(0)
Mar 18 10:58:11.539: lapp_on_application: Current call state = 4 
Mar 18 10:58:11.539: lapp_on_msp_event: Page accept request arrived from fmsp
Mar 18 10:58:11.539: lapp_on_msp_event: Sending page accept event to the FMSP
Mar 18 10:58:11.539: lapp_on_msp_event: Pages processed = 1

!--- The first fax page is received.

Mar 18 10:58:11.539: lapp_on_change_state: old state(4) new state(4)
Mar 18 10:58:16.015: lapp_on_application: Incoming Event:
 (37 = CC_EV_FROM_DMSP_ON_PAGE_PROCESSED), CID(219), DISP(146)
Mar 18 10:58:16.015: lapp_on_application: Current call state = 4 
Mar 18 10:58:16.015: lapp_on_msp_event: Page processed event arrived from the DMSP
Mar 18 10:58:16.015: lapp_on_change_state: old state(4) new state(4)
Mar 18 10:58:30.719: lapp_on_application: Incoming Event:
 (36 = CC_EV_FROM_FMSP_ON_PAGE_ACCEPT_REQUESTED), CID(217), DISP(0)
Mar 18 10:58:30.719: lapp_on_application: Current call state = 4 
Mar 18 10:58:30.719: lapp_on_msp_event: Page accept request arrived from fmsp
Mar 18 10:58:30.719: lapp_on_msp_event: Sending page accept event to the FMSP
Mar 18 10:58:30.719: lapp_on_msp_event: Pages processed = 2

!--- The second fax page is received.

Mar 18 10:58:30.719: lapp_on_change_state: old state(4) new state(4)
Mar 18 10:58:32.199: lapp_on_application: Incoming Event:
 (37 = CC_EV_FROM_DMSP_ON_PAGE_PROCESSED), CID(219), DISP(0)
Mar 18 10:58:32.199: lapp_on_application: Current call state = 4 
Mar 18 10:58:32.199: lapp_on_msp_event: Page processed event arrived from the DMSP
Mar 18 10:58:32.199: lapp_on_change_state: old state(4) new state(4)
Mar 18 10:58:34.355: lapp_on_application: Incoming Event: (11 = CC_EV_CALL_DISCONNECTED),
 CID(218), DISP(0)
Mar 18 10:58:34.355: lapp_on_application: Current call state = 4 
Mar 18 10:58:34.355: lapp_on_call_disconnected: Call Disconnected - CID= 218 cause=
 0x10 call_state= 4
Mar 18 10:58:34.355: lapp_on_call_disconnected: MSPI disconnected
Mar 18 10:58:34.355: lapp_on_call_disconnected: Faxmail acknowledged by remote SMTP server
Mar 18 10:58:34.355: lapp_on_change_state: old state(4) new state(7)  
!--- FMSP_PAGE_ACCEPT_REQUESTED to CONFERENCE_DESTROYING

Mar 18 10:58:34.355: lapp_on_conference_cleanup: Destroying conferences... 
Mar 18 10:58:34.355: lapp_on_conference_cleanup: Destroying conference for VTSP & FMSP
Mar 18 10:58:34.355: lapp_on_conference_cleanup: Destroying conference for FMSP & DMSP
Mar 18 10:58:34.355: lapp_on_conference_cleanup: Destroying conference for DMSP & MSPI
Mar 18 10:58:34.355: lapp_on_application: Incoming Event: (30 = CC_EV_CONF_DESTROY_DONE),
 CID(217), DISP(0)
Mar 18 10:58:34.355: lapp_on_application: Current call state = 7 
Mar 18 10:58:34.355: lapp_on_conference_destroyed: FMSP/DMSP conference destroyed
Mar 18 10:58:34.355: lapp_on_conference_destroyed: Conference destroyed..... confID = 150
Mar 18 10:58:34.355: lapp_on_application: Incoming Event: (30 = CC_EV_CONF_DESTROY_DONE),
 CID(219), DISP(0)
Mar 18 10:58:34.355: lapp_on_application: Current call state = 7 
Mar 18 10:58:34.355: lapp_on_conference_destroyed: DMSP/MSPI conference destroyed
Mar 18 10:58:34.355: lapp_on_conference_destroyed: Conference destroyed..... confID = 151
Mar 18 10:58:34.355: lapp_on_application: Incoming Event: (30 = CC_EV_CONF_DESTROY_DONE),
 CID(216), DISP(0)
Mar 18 10:58:34.355: lapp_on_application: Current call state = 7 
Mar 18 10:58:34.355: lapp_on_conference_destroyed: VTSP/FMSP conference destroyed
Mar 18 10:58:34.355: lapp_on_conference_destroyed: Conference destroyed..... confID = 149
Mar 18 10:58:34.355: lapp_on_change_state: old state(7) new state(8)  
!--- CONFERENCE_DESTROYING to DISCONNECTING

Mar 18 10:58:34.355: lapp_on_conference_destroyed: All conferences are destroyed. 
Mar 18 10:58:34.355: lapp_on_change_state: old state(8) new state(8)
Mar 18 10:58:34.355: lapp_on_call_leg_cleanup: Sending disconnect for FMSP
Mar 18 10:58:34.359: lapp_on_call_leg_cleanup: Sending disconnect for DMSP
Mar 18 10:58:34.359: lapp_on_application: Incoming Event:
 (12 = CC_EV_CALL_DISCONNECT_DONE), CID(219), DISP(0)
Mar 18 10:58:34.359: lapp_on_application: Current call state = 8 
Mar 18 10:58:34.359: lapp_on_disconnect_done: Received call disconnect done ... callID = 219
Mar 18 10:58:34.359: lapp_on_disconnect_done: DMSP disconnect done
Mar 18 10:58:34.359: lapp_on_disconnect_done: Sending disconnect for MSPI
Mar 18 10:58:34.359: lapp_on_application: Incoming Event:
 (12 = CC_EV_CALL_DISCONNECT_DONE), CID(218), DISP(0)
Mar 18 10:58:34.359: lapp_on_application: Current call state = 8 
Mar 18 10:58:34.359: lapp_on_disconnect_done: Received call disconnect done ... callID = 218
Mar 18 10:58:34.359: lapp_on_disconnect_done: MSPI disconnect done
Mar 18 10:58:34.363: lapp_on_application: Incoming Event:
 (12 = CC_EV_CALL_DISCONNECT_DONE), CID(217), DISP(0)
Mar 18 10:58:34.363: lapp_on_application: Current call state = 8 
Mar 18 10:58:34.363: lapp_on_disconnect_done: Received call disconnect done ... callID = 217
Mar 18 10:58:34.363: lapp_on_disconnect_done: FMSP disconnect done
Mar 18 10:58:34.363: lapp_on_disconnect_done: Sending disconnect for VTSP
Mar 18 10:58:36.627: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 45 seconds
Mar 18 10:58:37.647: lapp_on_application: Incoming Event: (28 = CC_EV_CALL_FEATURE),
 CID(216), DISP(0)
Mar 18 10:58:37.647: lapp_on_application: Current call state = 8 
Mar 18 10:58:37.647: lapp_on_event_unsupported: Unsupported event received--- 
Mar 18 10:58:37.647: lapp_on_event_unsupported: EV(28=CC_EV_CALL_FEATURE),
 CID(216), disp(0)
Mar 18 10:58:37.647: lapp_on_event_unsupported: Current call state = 8 
Mar 18 10:58:37.651: lapp_on_application: Incoming Event:
 (12 = CC_EV_CALL_DISCONNECT_DONE), CID(216), DISP(0)
Mar 18 10:58:37.651: lapp_on_application: Current call state = 8 
Mar 18 10:58:37.651: lapp_on_disconnect_done: Received call disconnect done ... callID = 216
Mar 18 10:58:37.651: lapp_on_disconnect_done: VTSP disconnect done
Mar 18 10:58:37.651: lapp_on_disconnect_done: All the calls are now void or disconnected
Mar 18 10:58:37.651: lapp_on_change_state: old state(8) new state(9)
!---  DISCONNECTING to TERMINAL

Mar 18 10:58:37.651: lapp_on_call_terminate: Freeing the IVR call handoff record
Mar 18 10:58:37.655: lapp_on_call_terminate: Freeing the fax call record
vdtl-5300-7a#

/image/gif/paws/47763/onramp_faxing2.gif

Клиент, получающий электронное письмо, видит окно, подобное тому выше при открытии электронной почты с набором MDN. Ответ, который получает проситель, находится в форме электронного письма, посланного пользователю с текстовым сообщением, которое читает, "Это - получение для электронного письма, которое вы послали "8913144" <Fax=8913144@testlab-t37.com> в 18.03.2002 10:58. Это получение проверяет, что сообщение было отображено на компьютере получателя в 18.03.2002 11:07".

vdtl-5300-7a# debug mta send all 
All email send debugging is on
vdtl-5300-7a#
Mar 18 14:50:46.278: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 18 14:50:48.474: esmtp_client_engine_open:
 from=FAX=8915510@vdtl-5300-7a.testlab-t37.com, to=FAX=8913144@testlab-t37.com
Mar 18 14:50:48.474: esmtp_client_engine_add_headers: from_comment=Fax 
Mar 18 14:50:48.702: esmtp_client_work: socket 0 attempting to connect to
 IP address 172.18.106.36
Mar 18 14:50:48.702: esmtp_client_work: socket 0 readable for first time
Mar 18 14:50:48.702: esmtp_client_work: socket 0 readable for first time
Mar 18 14:50:48.706: (C)R: 220 testlab-smtp.testlab-t37.com Microsoft ESMTP MAIL Service,
 Version: 5.0.2195.4453 ready at Mon, 18 Mar 2002 14:49:51 -0500 
Mar 18 14:50:48.706: (C)S: EHLO vdtl-5300-7a.testlab-t37.com
Mar 18 14:50:49.166: (C)R: 250-testlab-smtp.testlab-t37.com Hello [15.80.7.11]
Mar 18 14:50:49.166: (C)R: 250-TURN
Mar 18 14:50:49.170: (C)R: 250-ATRN
Mar 18 14:50:49.170: (C)R: 250-SIZE
Mar 18 14:50:49.170: (C)R: 250-ETRN
Mar 18 14:50:49.170: (C)R: 250-PIPELINING
Mar 18 14:50:49.170: (C)R: 250-DSN
Mar 18 14:50:49.170: (C)R: 250-ENHANCEDSTATUSCODES
Mar 18 14:50:49.170: (C)R: 250-8bitmime
Mar 18 14:50:49.170: (C)R: 250-BINARYMIME
Mar 18 14:50:49.170: (C)R: 250-CHUNKING
Mar 18 14:50:49.170: (C)R: 250-VRFY
Mar 18 14:50:49.170: (C)R: 250-X-EXPS GSSAPI NTLM LOGIN
Mar 18 14:50:49.170: (C)R: 250-X-EXPS=LOGIN
Mar 18 14:50:49.170: (C)R: 250-AUTH GSSAPI NTLM LOGIN
Mar 18 14:50:49.170: (C)R: 250-AUTH=LOGIN
Mar 18 14:50:49.170: (C)R: 250-X-LINK2STATE
Mar 18 14:50:49.170: (C)R: 250-XEXCH50
Mar 18 14:50:49.170: (C)R: 250 OK
Mar 18 14:50:49.170: (C)S: MAIL FROM:<FAX=8915510@vdtl-5300-7a.testlab-t37.com> RET=HDRS
Mar 18 14:50:49.666: (C)R: 250 2.1.0 FAX=8915510@vdtl-5300-7a.testlab-t37.com....Sender OK
Mar 18 14:50:49.666: (C)S: RCPT TO:<FAX=8913144@testlab-t37.com> NOTIFY=SUCCESS,FAILURE
 ORCPT=rfc822;FAX+3D8915510@vdtl-5300-7a.testlab-t37.com
Mar 18 14:50:50.170: (C)R: 250 2.1.5 FAX=8913144@testlab-t37.com 
Mar 18 14:50:50.698: (C)R: 354 Start mail input; end with <CRLF>.<CRLF>
Mar 18 14:50:50.698: (C)S: Received: by vdtl-5300-7a.testlab-t37.com for
 <FAX=8913144@testlab-t37.com> (with Cisco NetWorks); Mon, 18 Mar 2002 14:50:50 -0500
Mar 18 14:50:50.698: (C)S: To: "8913144" <FAX=8913144@testlab-t37.com>
Mar 18 14:50:50.698: (C)S: Message-ID: <008C2002145050698@vdtl-5300-7a.testlab-t37.com>
Mar 18 14:50:50.702: (C)S: Date: Mon, 18 Mar 2002 14:50:50 -0500
Mar 18 14:50:50.702: (C)S: Subject: Fax from On-Ramp GW vdlt-5300-7a[DNIS=8913144]
 [ANI=8915510]
Mar 18 14:50:50.702: (C)S: X-Mailer: IOS (tm) 5300 Software (C5300-IS-M)
Mar 18 14:50:50.702: (C)S: Disposition-Notification-To: admin@testlab-t37.com
Mar 18 14:50:50.702: (C)S: MIME-Version: 1.0
Mar 18 14:50:50.702: (C)S: Content-Type: multipart/fax-message;
Mar 18 14:50:50.702: (C)S: boundary="yradnuoB=_008B2002145048474.vdtl-5300-7atestlab-t37.com"
Mar 18 14:50:50.702: (C)S: From: "Fax " <FAX=8915510@vdtl-5300-7a.testlab-t37.com>
Mar 18 14:50:50.702: (C)S: X-Account-Id: 0
Mar 18 14:51:05.702: (C)S: --yradnuoB=_008B2002145048474.vdtl-5300-7atestlab-t37.com
Mar 18 14:51:05.702: (C)S: Content-ID: <008D2002145105702@vdtl-5300-7a.testlab-t37.com>
Mar 18 14:51:05.702: (C)S: Content-Type: image/tiff; application=faxbw
Mar 18 14:51:05.702: (C)S: Content-Transfer-Encoding: base64
Mar 18 14:51:05.706: esmtp_client_work: writing lingering data for socket 0
Mar 18 14:51:05.714: esmtp_client_work: writing lingering data for socket 0
Mar 18 14:51:14.726: esmtp_client_work: writing lingering data for socket 0
Mar 18 14:51:14.734: esmtp_client_work: writing lingering data for socket 0
Mar 18 14:51:14.738: (C)S: --yradnuoB=_008B2002145048474.vdtl-5300-7atestlab-t37.com--
Mar 18 14:51:14.738: esmtp_client_work: Sending terminating dot ...(socket=0)
Mar 18 14:51:14.738: (C)S: .  
!--- This is the terminating dot to end the SMTP session.

Mar 18 14:51:14.986: (C)R: 250 2.6.0 <008C2002145050698@vdtl-5300-7a.testlab-t37.com>
 Queued mail for delivery
Mar 18 14:51:14.986: (C)S: QUIT
Mar 18 14:51:15.406: (C)R: 221 2.0.0 testlab-smtp.testlab-t37.com Service closing
 transmission channel
Mar 18 14:51:15.406: esmtp_client_work: Freeing ctx=0x6266946C
Mar 18 14:51:15.406: esmtp_client: returned from work, context freed
Mar 18 14:51:18.938: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 38 seconds
vdtl-5300-7a#
vdtl-5300-7a# debug dmsp fax-to-doc 
Doc MSP fax to doc debugging is on
vdtl-5300-7a#
Mar 18 14:53:03.338: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 18 14:53:05.530: docmsp_call_setup_request: callid=227 
Mar 18 14:53:05.530: docmsp_call_setup_request(): ramp data dir=ONRAMP, conf dir=DEST
Mar 18 14:53:05.534: docmsp_caps_ind: call id=227, src=225
Mar 18 14:53:05.534: docmsp_bridge cfid=156, srccid=227, dstcid=225

Mar 18 14:53:05.534: docmsp_bridge(): ramp data dir=ONRAMP, conf dir=DEST, encode out=2
Mar 18 14:53:06.530: docmsp_bridge cfid=157, srccid=227, dstcid=226

Mar 18 14:53:06.530: docmsp_bridge(): ramp data dir=ONRAMP, conf dir=SRC, encode out=2
Mar 18 14:53:11.510: docmsp_xmit: call id src=225, dst=227
Mar 18 14:53:11.510: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:12.350: docmsp_xmit: call id src=225, dst=227

!--- Output suppressed.

Mar 18 14:53:22.242: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:22.242: docmsp_get_msp_event_buffer: 
Mar 18 14:53:23.082: docmsp_xmit: call id src=225, dst=227
Mar 18 14:53:23.082: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:23.922: docmsp_xmit: call id src=225, dst=227

!--- Output suppressed.

Mar 18 14:53:36.950: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:38.430: docmsp_xmit: call id src=225, dst=227
Mar 18 14:53:38.430: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:38.434: docmsp_get_msp_event_buffer: 
Mar 18 14:53:41.022: docmsp_bdrop cfid=156, srccid=227, dstcid=225

Mar 18 14:53:41.022: docmsp_bdrop cfid=157, srccid=227, dstcid=226

Mar 18 14:53:41.026: docmsp_call_disconnect: callid=227 
Mar 18 14:53:41.026: docmsp_do_call_history: call id=227 
Mar 18 14:53:42.886: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 45 seconds
vdtl-5300-7a#

Примечание:  Команда адреса debug mmoip send email ничего не отображает на сам экран, но это очень полезно. Это использует маршрутизатор в качестве клиента SMTP для отправки электронного письма адресу, данному в команде отладки. Электронной почте определили предмет в конфигурации и от "mspi Тестовый пользователь". Это содержит текстовое дополнение с линией, "Это - тестовое сообщение электронной почты, передаваемое через Cisco Приведенные в действие Факсовые сообщения Либретто".

Это отладки для стороны факса OnRamp:

vdtl-5300-7a# debug fmsp send t30
FMSP send t30 debugging is on
vdtl-5300-7a#
Mar 19 14:50:04.604: t30 call4Leg=311, state=1, substate=4
Mar 19 14:50:04.604: received flag of modulation:
0 
Mar 19 14:50:04.628: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 19 14:50:06.252: msg dump:FF C0 C2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 1E 86 62 
Mar 19 14:50:06.252: 
Mar 19 14:50:06.252: t30 call4Leg=311, state=1, substate=4
Mar 19 14:50:06.252: received: TSI remote id string: Fax 

Mar 19 14:50:06.672: msg dump:FF C8 C1 0 47 E 
Mar 19 14:50:06.672: 
Mar 19 14:50:06.824: t30 call4Leg=311, state=1, substate=4
Mar 19 14:50:06.824: in response receive WAIT FOR CD
Mar 19 14:50:11.632: t30 call4Leg=311, state=1, substate=6
Mar 19 14:50:11.632: received flag of modulation:
8 
Mar 19 14:50:19.304: t30 call4Leg=311, state=1, substate=6
Mar 19 14:50:19.304: received flag of modulation:
0 
Mar 19 14:50:20.364: msg dump:FF C8 F2 
Mar 19 14:50:20.364: 
Mar 19 14:50:22.324: t30 call4Leg=311, state=1, substate=6
Mar 19 14:50:22.324: received flag of modulation:
8 
Mar 19 14:50:31.643: t30 call4Leg=311, state=1, substate=6
Mar 19 14:50:31.643: received flag of modulation:
0 
Mar 19 14:50:32.683: msg dump:FF C8 F4 
Mar 19 14:50:32.683: 
Mar 19 14:50:33.155: t30 call4Leg=311, state=0, substate=6
Mar 19 14:50:33.155: fax session aborted by aplication
Mar 19 14:50:37.295: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 38 seconds
vdtl-5300-7a#
vdtl-5300-7a#debug fmsp receive t30 
FMSP receive t30 debugging is on
vdtl-5300-7a#
Mar 19 14:46:26.536: t30 call4Leg=307, state=1, substate=3  
!--- state=PHASE_B_RECEIVE  substate=TX_DIS_DTC_BLOCK

Mar 19 14:46:26.536: CSI_PACKET(8913180) 
!--- The CSI option, which shows that the called number is 8913180, is
!--- controlled by the fax receive called-subscriber configuration.

Mar 19 14:46:26.536: t30 call4Leg=307, state=1, substate=3
Mar 19 14:46:26.536: DIS_PACKET(speed: 5, resolution: 1, encoding:
1 
Mar 19 14:46:26.536: t30 call4Leg=307, state=1, substate=4   
!--- Moved to substate RX_DCS_DTC_BLOCK.

Mar 19 14:46:26.536: fax2_response_receive: PROCESSING
Mar 19 14:46:29.452: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:29.452: fax2_response_receive: PROCESSING
Mar 19 14:46:29.476: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 19 14:46:30.736: t30 call4Leg=307, state=1, substate=3
Mar 19 14:46:30.736: CSI_PACKET(8913180) 
Mar 19 14:46:30.736: t30 call4Leg=307, state=1, substate=3
Mar 19 14:46:30.736: DIS_PACKET(speed: 5, resolution: 1, encoding:
1   
!--- speed=14400, resolution=, encoding=modified read

Mar 19 14:46:30.736: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:30.736: fax2_response_receive: PROCESSING
Mar 19 14:46:31.100: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.100: fax2_response_receive: PROCESSING
Mar 19 14:46:31.100: msg dump:FF C0 C2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 1E 86 62 
Mar 19 14:46:31.100: 
Mar 19 14:46:31.100: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.100: received: TSI remote id string: Fax 

Mar 19 14:46:31.100: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.100: fax2_response_receive: PROCESSING
Mar 19 14:46:31.532: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.532: fax2_response_receive: PROCESSING
Mar 19 14:46:31.532: msg dump:FF C8 C1 0 47 E 
Mar 19 14:46:31.532: 
Mar 19 14:46:31.532: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.532: fax2_response_receive: PROCESSING
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.672: in response receive WAIT FOR CD
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=9   
!--- The substate is changed to RX_TCF.

Mar 19 14:46:31.672: received DCS_PACKET, BR: 9,  
!--- BR=v.21 14400

resolution: 1, encoding: 1, remote_id_string: Fax          
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=10  
!--- The substate is changed to WAIT_FOR_FDR.

Mar 19 14:46:31.672: wait for ready for data from
application
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=12   
!--- The substate is changed to TX_TCF_RESPONSE.

Mar 19 14:46:31.672: send CFR_PACKET
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=6   
!--- The substate is changed to CONFIGURE_RX_DATA.

Mar 19 14:46:31.672: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:36.472: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:36.472: fax2_configure_rx_data:
DETECTED_DATA
Mar 19 14:46:36.472: t30 call4Leg=307, state=2, substate=43  
!--- state = PHASE_C_RECEIVE, substate=RX_FIRST_DATA_BYTE - starting to RX page data...

Mar 19 14:46:36.472: No data yet
Mar 19 14:46:43.872: t30 call4Leg=307, state=2, substate=14  
!--- The substate is changed to RX_DATA.

Mar 19 14:46:43.872: end of page
Mar 19 14:46:43.872: t30 call4Leg=307, state=1, substate=6  
!--- The substate is changed to CONFIGURE_RX_DATA.

Mar 19 14:46:43.872: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:43.872: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:43.872: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:44.140: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:44.140: fax2_configure_rx_data:
DETECTED_COMMAND
Mar 19 14:46:44.140: t30 call4Leg=307, state=1, substate=7  
!--- The substate is changed to RX_COMMAND.

Mar 19 14:46:44.140: fax2_command_receive: NO_COMMAND, T2
timer not expired
Mar 19 14:46:45.200: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:45.200: fax2_command_receive: PROCESSING
Mar 19 14:46:45.200: msg dump:FF C8 F2 
Mar 19 14:46:45.200: 
Mar 19 14:46:45.200: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:45.200: fax2_command_receive: PROCESSING
Mar 19 14:46:45.352: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:45.352: fax2_command_receive:
RECEIVED_COMMAND
Mar 19 14:46:45.352: t30 call4Leg=307, state=3, substate=8    
!--- The substate is changed to ROUTE_COMMAND.

Mar 19 14:46:45.352: received MPS  
!--- Received Multipage Signal.

Mar 19 14:46:45.352: t30 call4Leg=307, state=3, substate=10  
!--- The substate is changed to WAIT_FOR_FDR.

Mar 19 14:46:45.352: waiting for page acceptence by the application
Mar 19 14:46:45.352: t30 call4Leg=307, state=3, substate=17  
!--- The substate is changed to SCHEDULE_PP_RESPONSE.

Mar 19 14:46:45.352: send MCF   
!--- Send a Message Confirmation.

Mar 19 14:46:45.352: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:45.352: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:47.172: t30 call4Leg=307, state=1, substate=6

!--- Now this must be done again, starting from the page data, because two pages
!--- are being sent.


Mar 19 14:46:47.172: fax2_configure_rx_data:
DETECTED_DATA
Mar 19 14:46:47.172: t30 call4Leg=307, state=2, substate=43
!--- state = PHASE_C_RECEIVE, substate=RX_FIRST_DATA_BYTE - starting to RX page data...

Mar 19 14:46:47.172: No data yet
Mar 19 14:46:56.212: t30 call4Leg=307, state=2, substate=14 
!--- The substate is changed to RX_DATA.

Mar 19 14:46:56.212: end of page
Mar 19 14:46:56.212: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:56.212: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:56.212: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:56.212: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:56.512: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:56.512: fax2_configure_rx_data:
DETECTED_COMMAND
Mar 19 14:46:56.512: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:56.512: fax2_command_receive: NO_COMMAND, T2
timer not expired
Mar 19 14:46:57.552: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:57.552: fax2_command_receive: PROCESSING
Mar 19 14:46:57.552: msg dump:FF C8 F4 
Mar 19 14:46:57.552: 
Mar 19 14:46:57.552: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:57.552: fax2_command_receive: PROCESSING
Mar 19 14:46:57.700: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:57.700: fax2_command_receive:
RECEIVED_COMMAND
Mar 19 14:46:57.700: t30 call4Leg=307, state=3, substate=8
Mar 19 14:46:57.700: received EOP   

!--- Received End of Procedure.

Mar 19 14:46:57.700: t30 call4Leg=307, state=3, substate=10
Mar 19 14:46:57.700: waiting for page acceptence by the application
Mar 19 14:46:57.700: t30 call4Leg=307, state=3, substate=17
Mar 19 14:46:57.700: send MCF       

!--- Send a Message Confirmation.

Mar 19 14:46:57.700: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:57.704: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:58.140: t30 call4Leg=307, state=0, substate=6  

!--- state=PHASE_IDLE

Mar 19 14:46:58.140: fax session aborted by aplication
Mar 19 14:47:02.188: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 38 seconds
vdtl-5300-7a#
vdtl-5300-7a# debug fax relay t30 called-number 8913144
Debugging fax relay t30 to 8913144
vdtl-5300-7a#
Mar 19 14:40:19.134: 0:D:302 1205778176 fr-entered (10ms)
Mar 19 14:40:22.498: 0:D:302 1205781540 fr-msg-tx CSI
Mar 19 14:40:23.826: 0:D:302 1205782870 fr-msg-tx DIS
Mar 19 14:40:25.070: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 19 14:40:26.146: 0:D:302 1205785190 fr-msg-det TSI
Mar 19 14:40:27.026: 0:D:302 1205786070 fr-msg-det DCS
Mar 19 14:40:30.558: 0:D:302 1205789600 fr-msg-tx CFR
Mar 19 14:40:40.766: 0:D:302 1205799810 fr-msg-det MPS
Mar 19 14:40:41.266: 0:D:302 1205800310 fr-msg-tx MCF
Mar 19 14:40:53.098: 0:D:302 1205812140 fr-msg-det EOP
Mar 19 14:40:53.598: 0:D:302 1205812640 fr-msg-tx MCF
Mar 19 14:40:56.390: 0:D:302 1205815430 fr-msg-det DCN
Mar 19 14:40:57.682: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 38 seconds
Mar 19 14:40:58.518: 0:D:302 1205817560 fr-end-dcn

fr-msg-tx indicates T.30 messages that are transmitted by the router
fr-msg-det indicates T.30 messages that are received by the router

Для получения дополнительной информации обратитесь к Руководству по поиску и устранению проблем Ретрансляции факса.

команды "show"

vdtl-5300-7a# show call history fax brief 
<ID>: <start>hs.<index> +<connect> +<disc> pid:<peer_id> <direction> <addr>
dur hh:mm:ss tx:<packets>/<bytes> rx:<packets>/<bytes> <disc-cause>(<text>)
IP <ip>:<udp> rtt:<time>ms pl:<play>/<gap>ms lost:<lost>/<early>/<late>
delay:<last>/<min>/<max>ms <codec>
MODEMPASS <method> buf:<fills>/<drains> loss <overall%> <multipkt>/<corrected>
last <buf event time>s dur:<Min>/<Max>s
FR <protocol> [int dlci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>
<codec> (payload size)
ATM <protocol> [int vpi/vci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>
<codec> (payload size)
Telephony <int>: tx:<tot>/<voice>/<fax>ms <codec> noise:<lvl>dBm acom:<lvl>dBm
Proxy <ip>:<audio udp>,<video udp>,<tcp0>,<tcp1>,<tcp2>,<tcp3> endpt: <type>/<manf>
bw: <req>/<act> codec: <audio>/<video>
tx: <audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120 pkts>/<t120 bytes>
rx: <audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120 pkts>/<t120 bytes>


Telephony call-legs: 3
SIP call-legs: 0
H323 call-legs: 0
Total call-legs: 5
1225 : 374672hs.31 +2 +1367 pid:8913180 Answer 8915510
dur 00:00:13 tx:7/124 rx:104/693 10 :1F (normal call clearing (16):normal,
 unspecified (31): User abort)
Telephony 0:D:61: tx:0/0/0ms 14400 noise:0dBm acom:0dBm

122B : 401714hs.32 +100 +2966 pid:1 Originate andy@testlab-t37.com
dur 00:00:28 tx:50942/0 rx:0/0 10 :0 (normal call clearing (16):)
IP 172.18.106.36 AcceptedMime:0 DiscardedMime:0

1229 : 400917hs.33 +1 +4108 pid:8913180 Answer 8915510
dur 00:00:41 tx:11/164 rx:760/45251 10 :10 (normal call clearing (16):normal
 call clearing (16): Normal conn)
Telephony 0:D:64: tx:0/0/0ms 14400 noise:0dBm acom:0dBm

1230 : 439580hs.34 +100 +2971 pid:1 Originate andy@testlab-t37.com
dur 00:00:28 tx:50942/0 rx:0/0 10 :0 (normal call clearing (16):)
IP 172.18.106.36 AcceptedMime:0 DiscardedMime:0

122E : 438783hs.35 +1 +4109 pid:8913180 Answer 8915510
dur 00:00:41 tx:11/164 rx:761/45256 10 :10 (normal call clearing (16):normal
 call clearing (16): Normal conn)
Telephony 0:D:68: tx:0/0/0ms 14400 noise:0dBm acom:0dBm

Дополнительные сведения


Document ID: 47763