Routers : Routers de servicios integrados de Cisco de la serie 3800

La conexión PPTP con la zona basó el router de escudo de protección con el ejemplo de la configuración del NAT

13 Agosto 2015 - Traducción Automática
Otras Versiones: PDFpdf | Inglés (22 Septiembre 2014) | Comentarios


Contenido


Introducción

Esta configuración de ejemplo demuestra cómo configurar un router con un firewall basado en zona y la configuración NAT para que sirva como terminación de las conexiones PPTP (Point-to-Point Tunneling Protocol).

prerrequisitos

Requisitos

No hay requisitos específicos para este documento.

Componentes Utilizados

La información que contiene este documento se basa en las siguientes versiones de software y hardware.

  • Router Cisco 871

  • Software Release 12.4T y Posterior del � del Cisco IOS

La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener cualquier comando.

Convenciones

Consulte Convenciones de Consejos Técnicos de Cisco para obtener más información sobre las convenciones sobre documentos.

Antecedentes

La red interna tiene un servidor que los usuarios en Internet puedan accederlos una vez estén conectados con el PPTP que termina en Internet que hace frente al router. El resto del acceso a los hosts en la red interna se niega de los usuarios externos.

  • Dirección IP del servidor interno — 10.22.22.10

  • Dirección IP del cliente remoto PC — 10.66.83.50

No prohiben todos los usuarios en la red interna el acceso sin restricciones a Internet. Estos usuarios internos utilizan la PALMADITA en el router para alcanzar Internet. Todo el tráfico de los usuarios internos se examina en el paso a través del router.

Configurar

En esta sección encontrará la información para configurar las funciones descritas en este documento.

Nota: Utilice la herramienta Command Lookup Tool (clientes registrados solamente) para obtener más información sobre los comandos utilizados en esta sección.

Diagrama de la red

En este documento, se utiliza esta configuración de red:

/image/gif/paws/110353/pptp-nat-config-example-01.gif

Configuración del router PPTP

Este documento utiliza esta configuración.

Estos comandos cisco ios son aplicables a todas las Plataformas que soporten el PPTP.

Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.


!--- Enable virtual private dial-up networking.


Router(config)#vpdn enable


!--- Enters VPDN group configuration mode for the specified VPDN group.


Router(config)#vpdn-group 1


!--- Enters VPDN accept-dialin configuration mode 
!--- and enables the router to accept dial-in requests.


Router(config-vpdn)#accept-dialin


!--- Specifies which PPTP protocol is used.


Router(config-vpdn-acc-in)#protocol pptp


!--- Specifies the virtual template that is used 
!--- in order to clone the virtual access interface.


Router(config-vpdn-acc-in)#virtual-template 1
Router(config-vpdn-acc-in)#exit

Router(config)#ip local pool defaultpool 192.168.100.1 192.168.100.254


!--- Create virtual-template interface used for cloning
!--- virtual-access interfaces with the use of address pool defaultpool
!--- with Challenge Authentication Protocol (CHAP) authentication and MS-CHAP.


Router(config)#interface virtual-template 1

Router(config-if)#encapsulation ppp
Router(config-if)#peer default ip address pool defaultpool
Router(config-if)#ip unnumbered FastEthernet4
Router(config-if)#ppp authentication chap ms-chap

Nota: Los comandos no valor por defecto se muestran en intrépido.

Router
Router#show run
Building configuration...

Current configuration : 3666 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot system flash flash:c870-advsecurityk9-mz.124-20.T3.bin
boot-end-marker
!
logging message-counter syslog
enable password cisco
!
aaa new-model
!
!
aaa authentication login VTY local
!

!--- Define local authentication for PPP.

!
aaa authentication ppp default local
!         
!
aaa session-id common
!
!
dot11 syslog
ip source-route
!
!
ip cef
ip domain name cisco.com
!
!
vpdn enable
!

!--- Enable VDPN.

!
vpdn-group PPTP-VPDN
!

!--- Default PPTP VPDN group.

!
 accept-dialin
  protocol pptp
  virtual-template 1
!
!

!--- Defining local username and password.

!
username cisco privilege 15 password 0 cisco
!
archive
 log config
  hidekeys
!
!
ip ssh version 1
!

!--- Defining Zone-Based Policy Firewall Class-Maps.

!
class-map type inspect match-all PPTP-Pass-Through-Traffic
 match access-group name PPTP-PASS-THROUGH
class-map type inspect match-any All-Traffic
 match protocol tcp
 match protocol udp
 match protocol icmp
class-map type inspect match-all Router-Access-Traffic
 match access-group name Router-Access
class-map type inspect match-all PPTP-Terminated-Traffic
 match access-group name PPTP-TERMINATED
!
!

!--- Defining Zone-Based Policy Firewall Policy-Maps.

!
policy-map type inspect PPTP-In-Policy
 class type inspect All-Traffic
  inspect 
 class class-default
  drop
policy-map type inspect Out-In-Policy
 class type inspect PPTP-Pass-Through-Traffic
  pass
 class class-default
  drop
policy-map type inspect In-Out-Policy
 class type inspect PPTP-Pass-Through-Traffic
  pass
 class type inspect All-Traffic
  inspect 
 class class-default
  drop
policy-map type inspect Out-Self-Policy
 class type inspect Router-Access-Traffic
  pass
 class type inspect PPTP-Terminated-Traffic
  pass
 class class-default
  drop    
!

!--- Defining the different zones.

!
zone security outside
zone security inside
zone security pptp
!

!--- Defining the zone-pairs for different flows of traffic.

!
zone-pair security outside-self source outside destination self
 service-policy type inspect Out-Self-Policy
zone-pair security pptp-in source pptp destination inside
 service-policy type inspect PPTP-In-Policy
zone-pair security inside-outside source inside destination outside
 service-policy type inspect In-Out-Policy
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
 description "Connected to Outside Network"
 ip address 10.66.79.73 255.255.255.224
!

!--- Defines the interface as external for NAT.

!
 ip nat outside
 ip virtual-reassembly
!

!--- Defines the interface as part of the outside zone.

!
 zone-member security outside
 speed 100
 full-duplex
!

!--- Create virtual-template interface used for cloning
!--- virtual-access interfaces with the use of address pool defaultpool
!--- with CHAP authentication and MS-CHAP.

!
interface Virtual-Template1
 ip unnumbered FastEthernet4
!

!--- Defines the interface as part of the pptp zone.

!
 zone-member security pptp
 peer default ip address pool defaultpool
 ppp authentication chap ms-chap
!
interface Dot11Radio0
 no ip address
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
 station-role root
!
interface Vlan1
 description "Connected to Inside Network"
 ip address 10.22.22.1 255.255.255.0
!

!--- Defines the interface as internal for NAT.

!
 ip nat inside
 ip virtual-reassembly
!

!--- Defines the interface as part of the inside zone.

!
 zone-member security inside
!

!--- Enable Create IP pool named test and specify IP range.

!
ip local pool defaultpool 192.168.100.1 192.168.100.254
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.66.79.65
no ip http server
no ip http secure-server
!

!--- Indicates that any packets received on the inside interface  
!--- matched by access list NO-NAT share one public IP address (the
!--- address on Fa4).
!--- Note that traffic from the internal network to the remote clients
!--- is not natted.

!
ip nat inside source list NO-NAT interface FastEthernet4 overload
!

!--- Traffic from internal network to remote clients is denied from 
!--- being natted.

!
ip access-list extended NO-NAT
 deny   ip 10.22.22.0 0.0.0.255 192.168.100.0 0.0.0.255
 permit ip 10.22.22.0 0.0.0.255 any
!

!--- Passing PPTP traffic includes allowing GRE – IP protocol 47.

!
ip access-list extended PPTP-PASS-THROUGH
 permit gre any any
!

!--- PPTP terminated traffic involves GRE and TCP port 1723 traffic.

!
ip access-list extended PPTP-TERMINATED
 permit gre any any
 permit tcp any any eq 1723
!

!--- Allowing Telnet, SSH and HTTPS access

!
ip access-list extended Router-Access
 permit tcp any any eq telnet
 permit tcp any any eq 22
 permit tcp any any eq 443
!
control-plane
!
!
line con 0
 no modem enable
line aux 0
line vty 0 4
 login authentication VTY
 transport input telnet ssh
!
scheduler max-task-time 5000
end

Configuración y configuraciones de cliente PPTP

Complete estos pasos:

  1. Elija el Start (Inicio) > Settings (Configuración) > Network and dial-up connections (Conexiones de red y marcado manual) > Make new connection (Crear una conexión nueva).

  2. Después de que aparezca la ventana del asistente de conexión de red, elija el tipo de conexión de red > conectan con la red en mi lugar de trabajo y hacen clic después.

    /image/gif/paws/110353/pptp-nat-config-example-02.gif

  3. Elija la conexión de Virtual Private Network.

    /image/gif/paws/110353/pptp-nat-config-example-03.gif

  4. Especifique un nombre de la conexión.

    /image/gif/paws/110353/pptp-nat-config-example-04.gif

  5. Especifique a una dirección destino en el campo del host o de la dirección IP y haga clic después.

    /image/gif/paws/110353/pptp-nat-config-example-05.gif

  6. Elija el comienzo > las configuraciones > la red y el dial encima de las conexiones y seleccione la conexión recientemente configurada.

  7. Después de que aparezca esta ventana, elija el Properties (Propiedades) > Security (Seguridad) para fijar la opción correctamente.

  8. Elija avanzado (las configuraciones del cliente) > las configuraciones, y elija el nivel y la autenticación apropiados del cifrado (encripción de datos) (permita estos protocolos) si es necesario.

    /image/gif/paws/110353/pptp-nat-config-example-06.gif

  9. Elija el establecimiento de una red > el tipo de VPN > PPTP VPN y haga clic la AUTORIZACIÓN.

    /image/gif/paws/110353/pptp-nat-config-example-07.gif

  10. Ingrese el nombre de usuario y contraseña que se utilizará para la conexión PPTP.

    /image/gif/paws/110353/pptp-nat-config-example-08.gif

  11. La ventana del nombre de usuario y contraseña que verifica aparece.

  12. El registro de su ordenador en la ventana de la red aparece.

  13. Si usted verifica la PC remota, usted consigue una dirección IP de la agrupación configurada.

    /image/gif/paws/110353/pptp-nat-config-example-09.gif

Verificación

Use esta sección para confirmar que su configuración funciona correctamente.

La herramienta Output Interpreter Tool (clientes registrados solamente) (OIT) soporta ciertos comandos show. Utilice la OIT para ver un análisis del resultado del comando show.

  1. Vpdn de Router#show

    %No active L2TP tunnels
    
    PPTP Tunnel and Session Information Total tunnels 1 sessions 1
    
    LocID Remote Name     State    Remote Address  Port  Sessions VPDN Group
    3                     estabd   10.66.83.50     1040  1        PPTP-VPDN      
    
    LocID RemID TunID Intf    Username      State   Last Chg Uniq ID
    3     32768 3     Vi2.1   cisco         estabd  00:00:57 2   
  2. Router#show ip interface brief

    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0              unassigned      YES unset  up	up      
    FastEthernet1              unassigned      YES unset  up	down    
    FastEthernet2              unassigned      YES unset  up	down    
    FastEthernet3              unassigned      YES unset  up	down    
    FastEthernet4              10.66.79.73     YES manual up	up      
    Dot11Radio0                unassigned      YES unset  down   down    
    SSLVPN-VIF0                unassigned      NO  unset  up	up      
    Vlan1                      10.22.22.1     YES manual up	up      
    NVI0                       unassigned      NO  unset  up	up      
    Virtual-Template1          10.66.79.73     YES TFTP   down	down    
    Virtual-Access1            unassigned      YES unset  down	down    
    Virtual-Access2            unassigned      YES unset  up	up      
    Virtual-Access2.1          10.66.79.73     YES TFTP   up	up
    
  3. Ruta de IP de Router#show

    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is 10.66.79.65 to network 0.0.0.0
    
    C    10.22.22.0/24 is directly connected, Vlan1
         10.0.0.0/27 is subnetted, 1 subnets
    C       10.66.79.64 is directly connected, FastEthernet4
         192.168.100.0/32 is subnetted, 1 subnets
    C       192.168.100.1 is directly connected, Virtual-Access2.1
    S*   0.0.0.0/0 [1/0] via 10.66.79.65
  4. Usuarios de Router#show

        Line       User       Host(s)              Idle       Location
    *  0 con 0                idle                 00:00:00   
    
      Interface    User               Mode         Idle     Peer Address
      Vi2.1        cisco              PPPoVPDN     -        192.168.100.1
    
  5. Ping del cliente conectado al servidor interno

    pptp-nat-config-example-10.gif

  6. El tipo del directiva-mapa de Router#show examina las sesiones de los zona-pares

    policy exists on zp outside-self
     Zone-pair: outside-self
    
      Service-policy inspect : Out-Self-Policy
    
        Class-map: Router-Access-Traffic (match-all)
          Match: access-group name Router-Access
          Pass
            14 packets, 358 bytes
    
        Class-map: PPTP-Terminated-Traffic (match-all)
          Match: access-group name PPTP-TERMINATED
          Pass
            52 packets, 4466 bytes
    
        Class-map: class-default (match-any)
          Match: any 
          Drop
            21 packets, 1680 bytes
    
    policy exists on zp pptp-in
     Zone-pair: pptp-in
              
      Service-policy inspect : PPTP-In-Policy
    
        Class-map: All-Traffic (match-any)
          Match: protocol tcp
            0 packets, 0 bytes
            30 second rate 0 bps
          Match: protocol udp
            0 packets, 0 bytes
            30 second rate 0 bps
          Match: protocol icmp
            1 packets, 40 bytes
            30 second rate 0 bps
    
       Inspect
    
        Class-map: class-default (match-any)
          Match: any 
          Drop
            0 packets, 0 bytes
    
    policy exists on zp inside-outside
     Zone-pair: inside-outside
              
      Service-policy inspect : In-Out-Policy
    
        Class-map: PPTP-Pass-Through-Traffic (match-all)
          Match: access-group name PPTP-PASS-THROUGH
          Pass
            4 packets, 320 bytes
    
        Class-map: All-Traffic (match-any)
          Match: protocol tcp
            31 packets, 868 bytes
            30 second rate 0 bps
          Match: protocol udp
            20 packets, 1271 bytes
            30 second rate 0 bps
          Match: protocol icmp
            0 packets, 0 bytes
            30 second rate 0 bps
    
       Inspect
    
          Number of Half-open Sessions = 6
          Half-open Sessions
            Session 83B5B920 (10.22.22.10:2135)=>(10.66.79.245:443) https:tcp SIS_OPENING
              Created 00:00:26, Last heard 00:00:26
              Bytes sent (initiator:responder) [0:0]
            Session 83B5BB20 (10.66.79.241:138)=>(10.66.79.255:138) netbios-dgm:udp SIS_OPENING
              Created 00:00:26, Last heard 00:00:13
              Bytes sent (initiator:responder) [406:0]
            Session 83B5BD20 (192.168.212.14:138)=>(192.168.212.255:138) netbios-dgm:udp SIS_OPENING
              Created 00:00:23, Last heard 00:00:23
              Bytes sent (initiator:responder) [233:0]
            Session 83B5C120 (10.22.22.10:2138)=>(10.66.79.245:443) https:tcp SIS_OPENING
              Created 00:00:19, Last heard 00:00:19
              Bytes sent (initiator:responder) [0:0]
            Session 83B5C320 (10.22.22.10:2142)=>(10.66.79.245:443) https:tcp SIS_OPENING
              Created 00:00:12, Last heard 00:00:12
              Bytes sent (initiator:responder) [0:0]
            Session 83B5C520 (10.22.22.10:2145)=>(10.66.79.245:443) https:tcp SIS_OPENING
              Created 00:00:05, Last heard 00:00:05
              Bytes sent (initiator:responder) [0:0]
    
    
        Class-map: class-default (match-any)
          Match: any 
          Drop
            0 packets, 0 bytes
  7. Debugging de Router#show

    PPP:
      PPP authentication debugging is on
      PPP protocol negotiation debugging is on
    VPN:
      VPDN events debugging is on
    
    
    !--- When the PPTP User is connecting 
     
    
    *Mar 13 02:22:40.535: VPDN Received L2TUN socket message <xCRQ - Session Incoming>
    *Mar 13 02:22:40.547: VPDN Tnl/Sn 2 2 L2TUN socket session accept requested
    *Mar 13 02:22:40.547: VPDN Tnl/Sn 2 2 Setting up dataplane for L2-L2, no idb
    *Mar 13 02:22:40.567: VPDN Received L2TUN socket message <xCCN - Session Connected>
    *Mar 13 02:22:40.595: VPDN uid:1 VPDN session up
    *Mar 13 02:22:40.607: ppp1 PPP: Send Message[Dynamic Bind Response]
    *Mar 13 02:22:40.607: ppp1 PPP: Using vpn set call direction
    *Mar 13 02:22:40.607: ppp1 PPP: Treating connection as a callin
    *Mar 13 02:22:40.607: ppp1 PPP: Session handle[8000003] Session id[1]
    *Mar 13 02:22:40.607: ppp1 PPP: Phase is ESTABLISHING, Passive Open
    *Mar 13 02:22:40.607: ppp1 LCP: State is Listen
    *Mar 13 02:22:42.563: ppp1 LCP: I CONFREQ [Listen] id 1 len 21
    *Mar 13 02:22:42.563: ppp1 LCP:    MRU 1400 (0x01040578)
    *Mar 13 02:22:42.563: ppp1 LCP:    MagicNumber 0x069878CA (0x0506069878CA)
    *Mar 13 02:22:42.563: ppp1 LCP:    PFC (0x0702)
    *Mar 13 02:22:42.563: ppp1 LCP:    ACFC (0x0802)
    *Mar 13 02:22:42.563: ppp1 LCP:    Callback 6  (0x0D0306)
    *Mar 13 02:22:42.563: ppp1 PPP: Authorization NOT required
    *Mar 13 02:22:42.563: ppp1 LCP: O CONFREQ [Listen] id 1 len 15
    *Mar 13 02:22:42.563: ppp1 LCP:    AuthProto CHAP (0x0305C22305)
    *Mar 13 02:22:42.563: ppp1 LCP:    MagicNumber 0x14AF18DB (0x050614AF18DB)
    *Mar 13 02:22:42.563: ppp1 LCP: O CONFREJ [Listen] id 1 len 7
    *Mar 13 02:22:42.563: ppp1 LCP:    Callback 6  (0x0D0306)
    *Mar 13 02:22:42.567: ppp1 LCP: I CONFACK [REQsent] id 1 len 15
    *Mar 13 02:22:42.567: ppp1 LCP:    AuthProto CHAP (0x0305C22305)
    *Mar 13 02:22:42.567: ppp1 LCP:    MagicNumber 0x14AF18DB (0x050614AF18DB)
    *Mar 13 02:22:42.567: ppp1 LCP: I CONFREQ [ACKrcvd] id 2 len 18
    *Mar 13 02:22:42.567: ppp1 LCP:    MRU 1400 (0x01040578)
    *Mar 13 02:22:42.567: ppp1 LCP:    MagicNumber 0x069878CA (0x0506069878CA)
    *Mar 13 02:22:42.567: ppp1 LCP:    PFC (0x0702)
    *Mar 13 02:22:42.567: ppp1 LCP:    ACFC (0x0802)
    *Mar 13 02:22:42.567: ppp1 LCP: O CONFNAK [ACKrcvd] id 2 len 8
    *Mar 13 02:22:42.567: ppp1 LCP:    MRU 1500 (0x010405DC)
    *Mar 13 02:22:42.571: ppp1 LCP: I CONFREQ [ACKrcvd] id 3 len 18
    *Mar 13 02:22:42.571: ppp1 LCP:    MRU 1400 (0x01040578)
    *Mar 13 02:22:42.571: ppp1 LCP:    MagicNumber 0x069878CA (0x0506069878CA)
    *Mar 13 02:22:42.571: ppp1 LCP:    PFC (0x0702)
    *Mar 13 02:22:42.571: ppp1 LCP:    ACFC (0x0802)
    *Mar 13 02:22:42.571: ppp1 LCP: O CONFNAK [ACKrcvd] id 3 len 8
    *Mar 13 02:22:42.571: ppp1 LCP:    MRU 1500 (0x010405DC)
    *Mar 13 02:22:42.571: ppp1 LCP: I CONFREQ [ACKrcvd] id 4 len 18
    *Mar 13 02:22:42.571: ppp1 LCP:    MRU 1500 (0x010405DC)
    *Mar 13 02:22:42.571: ppp1 LCP:    MagicNumber 0x069878CA (0x0506069878CA)
    *Mar 13 02:22:42.571: ppp1 LCP:    PFC (0x0702)
    *Mar 13 02:22:42.571: ppp1 LCP:    ACFC (0x0802)
    *Mar 13 02:22:42.575: ppp1 LCP: O CONFACK [ACKrcvd] id 4 len 18
    *Mar 13 02:22:42.575: ppp1 LCP:    MRU 1500 (0x010405DC)
    *Mar 13 02:22:42.575: ppp1 LCP:    MagicNumber 0x069878CA (0x0506069878CA)
    *Mar 13 02:22:42.575: ppp1 LCP:    PFC (0x0702)
    *Mar 13 02:22:42.575: ppp1 LCP:    ACFC (0x0802)
    *Mar 13 02:22:42.575: ppp1 LCP: State is Open
    *Mar 13 02:22:42.575: ppp1 PPP: Phase is AUTHENTICATING, by this end
    *Mar 13 02:22:42.575: ppp1 CHAP: O CHALLENGE id 1 len 33 from "Router"
    *Mar 13 02:22:42.575: ppp1 LCP: I IDENTIFY [Open] id 5 len 18 magic 0x069878CA MSRASV5.10
    *Mar 13 02:22:42.579: ppp1 LCP: I IDENTIFY [Open] id 6 len 31 magic 0x069878CA MSRAS-0-WINXP-RIKNIGHT-
    *Mar 13 02:22:42.579: ppp1 CHAP: I RESPONSE id 1 len 26 from "cisco"
    *Mar 13 02:22:42.579: ppp1 PPP: Phase is FORWARDING, Attempting Forward
    *Mar 13 02:22:42.579: ppp1 PPP: Phase is AUTHENTICATING, Unauthenticated User
    *Mar 13 02:22:42.579: ppp1 PPP: Sent CHAP LOGIN Request
    *Mar 13 02:22:42.583: ppp1 PPP: Received LOGIN Response PASS
    *Mar 13 02:22:42.583: ppp1 PPP: Phase is FORWARDING, Attempting Forward
    *Mar 13 02:22:42.583: ppp1 PPP: Send Message[Connect Local]
    L2X_ADJ: Vi2.1:midchain adj reqd for ip 0.0.0.0, cid 0
    L2X_ADJ: Vi2.1:midchain adj reqd for ip 0.0.0.0, cid 0
    *Mar 13 02:22:42.619: VPDN Vi2.1 Virtual interface created for unknown, bandwidth 100000 Kbps
    *Mar 13 02:22:42.619: VPDN Vi2.1 Setting up dataplane for L2-L3, Vi2.1
    *Mar 13 02:22:42.623: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
    L2X_ADJ: Vi2.1:allocated ctx, size 1
    *Mar 13 02:22:42.627: VPDN Received L2TUN socket message <Dataplane UP>
    *Mar 13 02:22:42.627: ppp1 PPP: Bind to [Virtual-Access2.1]
    *Mar 13 02:22:42.631: Vi2.1 PPP: Send Message[Static Bind Response]
    *Mar 13 02:22:42.631: Vi2.1 PPP: Phase is AUTHENTICATING, Authenticated User
    *Mar 13 02:22:42.631: Vi2.1 CHAP: O SUCCESS id 1 len 4
    *Mar 13 02:22:42.635: Vi2.1 PPP: Phase is UP
    *Mar 13 02:22:42.639: Vi2.1 IPCP: O CONFREQ [Closed] id 1 len 10
    *Mar 13 02:22:42.639: Vi2.1 IPCP:    Address 10.66.79.73 (0x03060A424F49)
    *Mar 13 02:22:42.639: Vi2.1 PPP: Process pending ncp packets
    *Mar 13 02:22:42.643: Vi2.1 CCP: I CONFREQ [Not negotiated] id 7 len 10
    *Mar 13 02:22:42.643: Vi2.1 CCP:    MS-PPC supported bits 0x01000001 (0x120601000001)
    *Mar 13 02:22:42.643: Vi2.1 LCP: O PROTREJ [Open] id 2 len 16 protocol CCP (0x80FD0107000A120601000001)
    *Mar 13 02:22:42.643: Vi2.1 IPCP: I CONFREQ [REQsent] id 8 len 34
    *Mar 13 02:22:42.643: Vi2.1 IPCP:    Address 0.0.0.0 (0x030600000000)
    *Mar 13 02:22:42.643: Vi2.1 IPCP:    PrimaryDNS 0.0.0.0 (0x810600000000)
    *Mar 13 02:22:42.643: Vi2.1 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
    *Mar 13 02:22:42.643: Vi2.1 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
    *Mar 13 02:22:42.643: Vi2.1 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
    *Mar 13 02:22:42.643: Vi2.1 IPCP: Pool returned 192.168.100.1
    *Mar 13 02:22:42.643: Vi2.1 IPCP: O CONFREJ [REQsent] id 8 len 28
    *Mar 13 02:22:42.647: Vi2.1 IPCP:    PrimaryDNS 0.0.0.0 (0x810600000000)
    *Mar 13 02:22:42.647: Vi2.1 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
    *Mar 13 02:22:42.647: Vi2.1 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
    *Mar 13 02:22:42.647: Vi2.1 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
    *Mar 13 02:22:42.647: Vi2.1 IPCP: I CONFACK [REQsent] id 1 len 10
    *Mar 13 02:22:42.647: Vi2.1 IPCP:    Address 10.66.79.73 (0x03060A424F49)
    *Mar 13 02:22:42.647: Vi2.1 IPCP: I CONFREQ [ACKrcvd] id 9 len 10
    *Mar 13 02:22:42.651: Vi2.1 IPCP:    Address 0.0.0.0 (0x030600000000)
    *Mar 13 02:22:42.651: Vi2.1 IPCP: O CONFNAK [ACKrcvd] id 9 len 10
    *Mar 13 02:22:42.651: Vi2.1 IPCP:    Address 192.168.100.1 (0x0306C0A86401)
    *Mar 13 02:22:42.651: Vi2.1 IPCP: I CONFREQ [ACKrcvd] id 10 len 10
    *Mar 13 02:22:42.651: Vi2.1 IPCP:    Address 192.168.100.1 (0x0306C0A86401)
    *Mar 13 02:22:42.651: Vi2.1 IPCP: O CONFACK [ACKrcvd] id 10 len 10
    *Mar 13 02:22:42.651: Vi2.1 IPCP:    Address 192.168.100.1 (0x0306C0A86401)
    *Mar 13 02:22:42.651: Vi2.1 IPCP: State is Open
    L2X_ADJ: Vi2.1:adj notify change, event 2
    L2X_ADJ: Vi2.1:midchain stacking IP 0.0.0.0 to 10.66.83.50 (VRF 0)
    L2X_ADJ: Vi2.1:adj notify change, event 8
    L2X_ADJ: Vi2.1:adj notify change, event 3
    *Mar 13 02:22:42.655: Vi2.1 IPCP: Install route to 192.168.100.1
    *Mar 13 02:22:43.623: %LINEPROTO-5-UPDOWN: Line protocol on Interface 
    Virtual-Access2, changed state to up
    
    
    !--- When the PPTP User is disconnecting
    
    
    *Mar 13 02:23:05.571: Vi2.1 LCP: I TERMREQ [Open] id 11 len 16 (0x069878CA003CCD7400000000)
    *Mar 13 02:23:05.571: Vi2.1 LCP: O TERMACK [Open] id 11 len 4
    *Mar 13 02:23:05.575: Vi2.1 PPP: Sending Acct Event[Down] id[4]
    *Mar 13 02:23:05.575: Vi2.1 PPP: Phase is TERMINATING
    *Mar 13 02:23:05.779: VPDN Received L2TUN socket message <CDN - Session Disconnected>
    *Mar 13 02:23:05.779: VPDN Vi2.1 disconnect (AAA) IETF: 1/user-request Ascend: 28/PPP Receive Term
    *Mar 13 02:23:05.779: VPDN Vi2.1 vpdn shutdown session, result=2, error=6, vendor_err=0, syslog_error_code=2, syslog_key_type=1
    *Mar 13 02:23:05.779: VPDN Vi2.1 VPDN/AAA: accounting stop sent
    *Mar 13 02:23:05.783: VPDN Vi2.1 Unbinding session from idb
    *Mar 13 02:23:05.783: Vi2.1 VPDN: Resetting interface
    *Mar 13 02:23:05.783: Vi2.1 PPP: Block vaccess from being freed [0x19]
    *Mar 13 02:23:05.783: Vi2.1 PPP: Received Disconnect from Lower Layer
    L2X_ADJ: Vi2.1:midchain unstacking IP 0.0.0.0
    L2X_ADJ: Vi2.1:adj notify change, event 8
    L2X_ADJ: Vi2.1:removed ctx
    *Mar 13 02:23:05.807: Vi2.1 LCP: State is Closed
    *Mar 13 02:23:05.807: Vi2.1 PPP: Phase is DOWN
    *Mar 13 02:23:05.807: Vi2.1 IPCP: State is Closed
    *Mar 13 02:23:05.807: Vi2.1 PPP: Unlocked by [0x1] Still Locked by [0x18]
    *Mar 13 02:23:05.807: Vi2.1 PPP: Unlocked by [0x10] Still Locked by [0x8]
    *Mar 13 02:23:05.811: Vi2.1 PPP: Unlocked by [0x8] Still Locked by [0x0]
    *Mar 13 02:23:05.811: Vi2.1 PPP: Free previously blocked vaccess

Troubleshooting

En esta sección encontrará información que puede utilizar para solucionar problemas de configuración.

  1. Aseegurese que el tráfico destinado al router permite el puerto TCP 1723 y el tráfico GRE.

  2. Aseegurese que el paso PPTP con el tráfico permite el GRE a través del router.

  3. Tenga cuidado del defecto CSCsr41631; esto se supera con el uso de diversas zonas para la interfaz externa y la interfaz de plantilla virtual.

Discusiones relacionadas de la comunidad de soporte de Cisco

La Comunidad de Soporte de Cisco es un foro donde usted puede preguntar y responder, ofrecer sugerencias y colaborar con colegas.


Información Relacionada


Document ID: 110353