Banda ancha por cable : Sistemas de terminación de cable módems (CMTS)

Configuraciones de muestra de gran disponibilidad N+1

18 Octubre 2015 - Traducción Automática
Otras Versiones: PDFpdf | Inglés (22 Agosto 2015) | Comentarios


Contenido


Introducción

Este documento proporciona los ejemplos de configuración y la información para varios escenarios N+1.

Nota: Tenga presente que le gustan los indicadores luminosos LED amarillo de la placa muestra gravedad menor debe sostener como los indicadores luminosos LED amarillo de la placa muestra gravedad menor.

Escenario 1

Configuraciones de muestra de la Alta disponibilidad (HA) con dos Switches RF (configuración 3x10) en 4+1 modos, cinco VXR, veinte linecards MC28C, y tres chasis del VCom HD4040, que contienen cuarenta módulos.

El diseño físico se muestra en el cuadro 1. refiere a telegrafiar el Cisco RF Switch al uBR7246VXR de Cisco.

Cuadro 1 – 4+1 con los indicadores luminosos LED amarillo de la placa muestra gravedad menor MC28C y 2 Switches RF

/image/gif/paws/49776/ha_mc5x20_a.gif

El este empilar de la comprobación se asume, con las asignaciones IP que comienzan con 192.168.1.2 en el top y continúan abajo. Porque estará en el modo 4+1, el RF Switch 1 se considera ser dos Switches: a y b, donde está los slots a 1 a 4 y b es el RF Switch 2 de los slots 5 a 8. también se considera dos Switches: a y B.

Configuración de trabajo VXR1
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname "WorkingVXR1"
!
boot system disk0:ubr7200-ik8s-mz.BC.28July03
no logging console
enable secret 5 $1$5YHG$mquxbcqzFoUUKhp/c9WT4/
!
cab modem remote-query 10 public
cab modulation-prof 2 request 0 16  0 8  qpsk  scrambler 152 no-diff 64  fixed uw8
cab modulation-prof 2 initial 5 34  0 48 qpsk  scrambler 152 no-diff 128 fixed uw16
cab modulation-prof 2 station 5 34  0 48 qpsk  scrambler 152 no-diff 128 fixed uw16
cab modulation-prof 2 short   4 76  6 8  qpsk  scrambler 152 no-diff 72  short uw8
cab modulation-prof 2 long    8 220 0 8  qpsk  scrambler 152 no-diff 80  short uw8
cab modulation-prof 3 request 0 16  0 8  qpsk  scrambler 152 no-diff 64  fixed uw16
cab modulation-prof 3 initial 5 34  0 48 qpsk  scrambler 152 no-diff 128 fixed uw16
cab modulation-prof 3 station 5 34  0 48 qpsk  scrambler 152 no-diff 128 fixed uw16
cab modulation-prof 3 short   7 76  7 8  16qam scrambler 152 no-diff 144 short uw16
cab modulation-prof 3 long    9 220 0 8  16qam scrambler 152 no-diff 160 short uw16
no cable qos permission create
no cable qos permission update
cable qos permission modems
no cable clock source-midplane
no cable clock force primary
no cable clock force secondary
!
cable config-file docsis.cm
 frequency 453000000
 service-class 1 max-upstream 10000
 service-class 1 max-downstream 10000
 service-class 1 max-burst 1522
!
ip subnet-zero
ip cef
!
ip host protect 192.168.1.7
ip host work2 192.168.1.6
ip name-server 171.68.226.120
!
ip dhcp pool MODEMS1
   network 192.168.3.0 255.255.255.0
   bootfile docsis.cm
   next-server 192.168.3.5
   default-router 192.168.3.5
   option 7 ip 192.168.3.5
   option 4 ip 192.168.3.5
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp pool PC
   network 10.11.12.0 255.255.255.0
   default-router 10.11.12.1
   dns-server 171.68.226.120
   lease 10 1 11
!
packetcable element_id 35417
!
interface FastEthernet0/0
 ip address 192.168.1.7 255.255.255.0
 no keepalive
 speed auto
 full-duplex

!--- This interface is used for Hot Standby Connection-to-Connection Protocol (HCCP)
!--- traffic.

!
interface FastEthernet0/1
 ip address 192.168.2.7 255.255.255.0
 keepalive 1

!--- This is set to 1 second so that, if the cable is disconnected, then this
!--- interface will failover within 3 seconds.

 speed auto
 full-duplex
!
interface Cable3/0
 ip address 10.11.12.1 255.255.255.0
 secondary ip address 192.168.3.5 255.255.255.0
 load-interval 30
 keepalive 1

!--- The keepalive time is in seconds, and the default is 10 seconds for HCCP code.

 load-interval 30
 cable downstream channel-id 0
 cable bundle 1 master

!--- Interface bundling is supported, as are subinterfaces.
!--- Note: Bundles failover together.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000

!--- This is the downstream (DS) frequency, which used to be informational only when
!--- you are using an external UPx. This must be set when you are using the MC28U cards
!--- with internal UPxs or when you are doing N+1 with MC28C cards, so that the Protect
!--- UPx knows what frequency to use.

 cable upstream 0 frequency 24000000

!--- If you are doing dense mode combining, the upstream (US) frequencies must be
!--- different. If no two US ports are shared, then the same frequency can be used.

 cable upstream 0 power-level 0
 cable upstream 0 channel-width 3200000
 cable upstream 0 minislot-size 2
 cable upstream 0 data-backoff automatic
 cable upstream 0 modulation-profile 3
 no cable upstream 0 shutdown
 cable dhcp-giaddr policy

!--- This tells the cable modems (CMs) to get an IP address from the primary scope, and
!--- it tells the customer premises equipment (CPE) to use the secondary scope.

 hccp 1 working 1

!--- This is the Working first group, member 1.

 hccp 1 channel-switch 1 rfsw1a rfswitch-group 192.168.1.5 44440400 1

!--- This is the IP address of the Switch, and it is protecting member 1 in the
!--- left side of Switch slot 1.

 hccp 1 channel-switch 1 uc31 wavecom-hd 192.168.1.2 1 192.168.1.4 1

!--- This is the IP address of the upconverter, and it is module 1 (A) that is backing
!--- module 1 (A) of another upconverter. This shows that one upconverter could have
!--- a module that backs up a module in a different chassis with a different IP address,
!--- if need be. If this statement is not present when you are using Cisco IOS� Software
!--- Release 15(BC2) or later, then IF-Muting is assumed, and an external upconverter
!--- with Simple Network Management Protocol (SNMP) capability is not needed.

 hccp 1 track FastEthernet0/1

!--- Tracking is enabled for the egress port, in the event that the WAN-backhaul is 
!--- disrupted. This cable interface will failover to the Protect.

 hccp 1 reverttime 120

!--- This is the time in minutes (plus a 2 minute suspend) for the card to switch back
!--- to normal mode, if the fault has cleared. If there is a fault on the Protect card,
!--- then it will revert back after the suspend time, and it will not wait for the full
!--- revert time. The default setting is 30 minutes.

!
interface Cable3/1
 hccp 2 working 1
 hccp 2 channel-switch 1 rfsw1a rfswitch-group 192.168.1.5 11110100 1

!--- This is the IP address of the Switch, and it is protecting member 1 in the
!--- right side of Switch slot 1.

 hccp 2 channel-switch 1 uc31 wavecom-hd 192.168.1.2 2 192.168.1.4 2
 hccp 2 reverttime 120
!
interface Cable4/0
 hccp 3 working 1 hccp 3 channel-switch 1 rfsw1b rfswitch-group 192.168.1.5 88880800 1

!--- This is the IP address of the Switch, and it is protecting member 1 in the
!--- left side of Switch slot 5. Because the RF Switch is in 4+1 mode, slot 5 is 
!--- considered to be slot 1 again.

 hccp 3 channel-switch 1 uc31 wavecom-hd 192.168.1.2 3 192.168.1.4 3
 hccp 3 reverttime 120
!
interface Cable 4/1
 hccp 4 working 1
 hccp 4 channel-switch 1 rfsw1b rfswitch-group 192.168.1.5 22220200 1

!--- This is the IP address of the Switch, and it is protecting member 1 in the
!--- right side of Switch slot 5. Because the RF Switch is in 4+1 mode, slot 5 is
!--- considered to be slot 1 again.

 hccp 4 channel-switch 1 uc31 wavecom-hd 192.168.1.2 4 192.168.1.4 4
 hccp 4 reverttime 120
!
interface Cable5/0
 hccp 5 working 1
 hccp 5 channel-switch 1 rfsw2a rfswitch-group 192.168.1.6 44440400 1
 hccp 5 channel-switch 1 uc31 wavecom-hd 192.168.1.2 5 192.168.1.4 5
 hccp 5 reverttime 120
!
interface Cable 5/1
 hccp 6 working 1
 hccp 6 channel-switch 1 rfsw2a rfswitch-group 192.168.1.6 11110100 1
 hccp 6 channel-switch 1 uc31 wavecom-hd 192.168.1.2 6 192.168.1.4 6
 hccp 6 reverttime 120
!
interface Cable 6/0
 hccp 7 working 1
 hccp 7 channel-switch 1 rfsw2b rfswitch-group 192.168.1.6 88880800 1
 hccp 7 channel-switch 1 uc31 wavecom-hd 192.168.1.2 7 192.168.1.4 7
 hccp 7 reverttime 120
!
interface Cable 6/1
 hccp 8 working 1
 hccp 8 channel-switch 1 rfsw2b rfswitch-group 192.168.1.6 22220200 1
 hccp 8 channel-switch 1 uc31 wavecom-hd 192.168.1.2 8 192.168.1.4 8
 hccp 8 reverttime 120
!
router eigrp 2500
 network 10.11.12.0 0.0.0.255
 network 192.168.1.0
 network 192.168.3.0
 no auto-summary
 no eigrp log-neighbor-changes
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.1.254
ip route 192.168.1.0 255.255.255.0 FastEthernet0/0
ip route 192.168.2.0 255.255.255.0 FastEthernet0/1
no ip http server
!
cdp run
!
snmp-server community private RW

!--- Unless it is deleted, this does not affect the HCCP communications between
!--- the upconverter, the Switch, and the 7200.

snmp-server community public RO
snmp-server enable traps tty
snmp-server manager
tftp-server disk0:
tftp-server disk1:
alias exec shb show hccp brief
alias exec shd show hccp detail
alias exec scm show cable modem
alias exec scr show cable modem remote
alias exec sm show cab modu
alias exec sch show cab hop
alias exec sc300 show cont c3/0 u0
alias exec sint300 show int c3/0 u0
alias exec scs show cable spec

Proteja la configuración de VXR
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname "ProtectVXR"
!
boot system disk0:ubr7200-ik8s-mz.BC.28July03
no logging console
enable secret 5 $1$5YHG$mquxbcqzFoUUKhp/c9WT4/
!
cab modem remote-query 10 public
cab modulation-prof 2 request 0 16  0 8  qpsk  scrambler 152 no-diff 64  fixed uw8
cab modulation-prof 2 initial 5 34  0 48 qpsk  scrambler 152 no-diff 128 fixed uw16
cab modulation-prof 2 station 5 34  0 48 qpsk  scrambler 152 no-diff 128 fixed uw16
cab modulation-prof 2 short   4 76  6 8  qpsk  scrambler 152 no-diff 72  short uw8
cab modulation-prof 2 long    8 220 0 8  qpsk  scrambler 152 no-diff 80  short uw8
cab modulation-prof 3 request 0 16  0 8  qpsk  scrambler 152 no-diff 64  fixed uw16
cab modulation-prof 3 initial 5 34  0 48 qpsk  scrambler 152 no-diff 128 fixed uw16
cab modulation-prof 3 station 5 34  0 48 qpsk  scrambler 152 no-diff 128 fixed uw16
cab modulation-prof 3 short   7 76  7 8  16qam scrambler 152 no-diff 144 short uw16
cab modulation-prof 3 long    9 220 0 8  16qam scrambler 152 no-diff 160 short uw16

!--- Be sure to pre-configure all global configurations on the Protect, such as
!--- modulation profiles, spectrum groups, load balancing, and so forth.

no cable qos permission create
no cable qos permission update
cable qos permission modems
no cable clock source-midplane
no cable clock force primary
no cable clock force secondary
!
cable config-file docsis.cm
 frequency 453000000
 service-class 1 max-upstream 10000
 service-class 1 max-downstream 10000
 service-class 1 max-burst 1522
!
ip subnet-zero
ip cef
!
ip host protect 192.168.1.7
ip host work2 192.168.1.6
ip name-server 171.68.226.120
!
ip dhcp pool MODEMS1
   network 192.168.3.0 255.255.255.0
   bootfile docsis.cm
   next-server 192.168.3.5
   default-router 192.168.3.5
   option 7 ip 192.168.3.5
   option 4 ip 192.168.3.5
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp pool PC
   network 10.11.12.0 255.255.255.0
   default-router 10.11.12.1
   dns-server 171.68.226.120
   lease 10 1 11
!
packetcable element_id 35417
!
interface FastEthernet0/0
 ip address 192.168.1.11 255.255.255.0
 no keepalive
 speed auto
 full-duplex
 no cdp enable
!
interface FastEthernet0/1
 ip address 192.168.2.11 255.255.255.0
 keepalive 1
 speed auto
 full-duplex
 no cdp enable
!
interface Cable3/0
 no ip address

!--- There is no need to set the IP address, because it will come from the Working card
!--- via SNMP.

 no keepalive

!--- This defaults to 10 seconds with the N+1 Cisco IOS code, but it is recommended that
!--- you disable it on the Protect interface or set it to a relatively high value.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32

!--- The DS modulation, annex mode, and interleave must be same on the Protect and on
!--- the Working of the same group.

 no shut

!--- The interface must be activated to start HCCP functionality. Do this last.

 cable upstream 0 shutdown

!--- This will automatically become "no shut" when a failover occurs.

 hccp 1 protect 1 192.168.1.7

!--- This is the Protect for the first group. Remember to configure the Protect
!--- interface(s) last, after the Working interfaces are configured. This is the HCCP
!--- first group and it is protecting member 1 with member 1’s FastEthernet (FE) IP
!--- address.

 hccp 1 channel-switch 1 rfsw1a rfswitch-group 192.168.1.5 44440400 1

!--- This is the IP address of the Switch, and it is protecting member 1, which has a
!--- bitmap of 44440400 in Switch slot 1.

 hccp 1 channel-switch 1 uc31 wavecom-hd 192.168.1.2 1 192.168.1.4 1

!--- This is the IP address of the upconverter, and it is module 1 (A) that is backing
!--- module 1 (A) of another upconverter. This shows that one upconverter could have
!--- a module that backs up a module in a different chassis with a different IP address,
!--- if need be. If this statement is not present when you are using Cisco IOS Software
!--- Release 15(BC2) or later, then IF-Muting is assumed, and an external upconverter
!--- with SNMP capability is not needed.

 hccp 1 protect 2 192.168.1.8

!--- This is the HCCP first group, and it is protecting member 2 with its IP address.

 hccp 1 channel-switch 2 rfsw1a rfswitch-group 192.168.1.5 44440400 2
 hccp 1 channel-switch 2 uc31 wavecom-hd 192.168.1.2 1 192.168.1.4 9
 hccp 1 protect 3 192.168.1.9
 hccp 1 channel-switch 3 rfsw1a rfswitch-group 192.168.1.5 44440400 3
 hccp 1 channel-switch 3 uc32 wavecom-hd 192.168.1.2 1 192.168.1.3 1
 hccp 1 protect 4 192.168.1.10
 hccp 1 channel-switch 4 rfsw1a rfswitch-group 192.168.1.5 44440400 4
 hccp 1 channel-switch 4 uc32 wavecom-hd 192.168.1.2 1 192.168.1.3 9
 hccp 1 timers 666 2000

!--- hccp 1 timers <hellotime> <holdtime>
!--- This is for inter-chassis communication.

!
interface Cable3/1
 hccp 2 protect 1 192.168.1.7
 hccp 2 channel-switch 1 rfsw1a rfswitch-group 192.168.1.5 11110100 1
 hccp 2 channel-switch 1 uc31 wavecom-hd 192.168.1.2 2 192.168.1.4 2
 hccp 2 protect 2 192.168.1.8
 hccp 2 channel-switch 2 rfsw1a rfswitch-group 192.168.1.5 11110100 2
 hccp 2 channel-switch 2 uc31 wavecom-hd 192.168.1.2 2 192.168.1.4 10
 hccp 2 protect 3 192.168.1.9
 hccp 2 channel-switch 3 rfsw1a rfswitch-group 192.168.1.5 11110100 3
 hccp 2 channel-switch 3 uc32 wavecom-hd 192.168.1.2 2 192.168.1.3 2
 hccp 2 protect 4 192.168.1.10
 hccp 2 channel-switch 4 rfsw1a rfswitch-group 192.168.1.5 11110100 4
 hccp 2 channel-switch 4 uc32 wavecom-hd 192.168.1.2 2 192.168.1.3 10
 hccp 2 timers 666 2000
!
interface Cable4/0
 hccp 3 protect 1 192.168.1.7
 hccp 3 channel-switch 1 rfsw1b rfswitch-group 192.168.1.5 88880800 1
 hccp 3 channel-switch 1 uc31 wavecom-hd 192.168.1.2 3 192.168.1.4 3
 hccp 3 protect 2 192.168.1.8
 hccp 3 channel-switch 2 rfsw1b rfswitch-group 192.168.1.5 88880800 2
 hccp 3 channel-switch 2 uc31 wavecom-hd 192.168.1.2 3 192.168.1.4 11
 hccp 3 protect 3 192.168.1.9
 hccp 3 channel-switch 3 rfsw1b rfswitch-group 192.168.1.5 88880800 3
 hccp 3 channel-switch 3 uc32 wavecom-hd 192.168.1.2 3 192.168.1.3 3
 hccp 3 protect 4 192.168.1.10
 hccp 3 channel-switch 4 rfsw1b rfswitch-group 192.168.1.5 88880800 4
 hccp 3 channel-switch 4 uc32 wavecom-hd 192.168.1.2 3 192.168.1.3 11
 hccp 3 timers 666 2000
!
interface Cable4/1
 hccp 4 protect 1 192.168.1.7
 hccp 4 channel-switch 1 rfsw1b rfswitch-group 192.168.1.5 22220200 1
 hccp 4 channel-switch 1 uc31 wavecom-hd 192.168.1.2 4 192.168.1.4 4
 hccp 4 protect 2 192.168.1.8
 hccp 4 channel-switch 2 rfsw1b rfswitch-group 192.168.1.5 22220200 2
 hccp 4 channel-switch 2 uc31 wavecom-hd 192.168.1.2 4 192.168.1.4 12
 hccp 4 protect 3 192.168.1.9
 hccp 4 channel-switch 3 rfsw1b rfswitch-group 192.168.1.5 22220200 3
 hccp 4 channel-switch 3 uc32 wavecom-hd 192.168.1.2 4 192.168.1.3 4
 hccp 4 protect 4 192.168.1.10
 hccp 4 channel-switch 4 rfsw1b rfswitch-group 192.168.1.5 22220200 4
 hccp 4 channel-switch 4 uc32 wavecom-hd 192.168.1.2 4 192.168.1.3 12
 hccp 4 timers 666 2000
!
interface Cable5/0
 hccp 5 protect 1 192.168.1.7
 hccp 5 channel-switch 1 rfsw2a rfswitch-group 192.168.1.6 44440400 1
 hccp 5 channel-switch 1 uc31 wavecom-hd 192.168.1.2 5 192.168.1.4 5
 hccp 5 protect 2 192.168.1.8
 hccp 5 channel-switch 2 rfsw2a rfswitch-group 192.168.1.6 44440400 2
 hccp 5 channel-switch 2 uc31 wavecom-hd 192.168.1.2 5 192.168.1.4 13
 hccp 5 protect 3 192.168.1.9
 hccp 5 channel-switch 3 rfsw2a rfswitch-group 192.168.1.6 44440400 3
 hccp 5 channel-switch 3 uc32 wavecom-hd 192.168.1.2 5 192.168.1.3 5
 hccp 5 protect 4 192.168.1.10
 hccp 5 channel-switch 4 rfsw2a rfswitch-group 192.168.1.6 44440400 4
 hccp 5 channel-switch 4 uc32 wavecom-hd 192.168.1.2 5 192.168.1.3 13
 hccp 5 timers 666 2000
!
interface Cable5/1
 hccp 6 protect 1 192.168.1.7
 hccp 6 channel-switch 1 rfsw2a rfswitch-group 192.168.1.6 11110100 1
 hccp 6 channel-switch 1 uc31 wavecom-hd 192.168.1.2 6 192.168.1.4 6
 hccp 6 protect 2 192.168.1.8
 hccp 6 channel-switch 2 rfsw2a rfswitch-group 192.168.1.6 11110100 2
 hccp 6 channel-switch 2 uc31 wavecom-hd 192.168.1.2 6 192.168.1.4 14
 hccp 6 protect 3 192.168.1.9
 hccp 6 channel-switch 3 rfsw2a rfswitch-group 192.168.1.6 11110100 3
 hccp 6 channel-switch 3 uc32 wavecom-hd 192.168.1.2 6 192.168.1.3 6
 hccp 6 protect 4 192.168.1.10
 hccp 6 channel-switch 4 rfsw2a rfswitch-group 192.168.1.6 11110100 4
 hccp 6 channel-switch 4 uc32 wavecom-hd 192.168.1.2 6 192.168.1.3 14
 hccp 6 timers 666 2000
!
interface Cable6/0
 hccp 7 protect 1 192.168.1.7
 hccp 7 channel-switch 1 rfsw2b rfswitch-group 192.168.1.6 88880800 1
 hccp 7 channel-switch 1 uc31 wavecom-hd 192.168.1.2 7 192.168.1.4 7
 hccp 7 protect 2 192.168.1.8
 hccp 7 channel-switch 2 rfsw2b rfswitch-group 192.168.1.6 88880800 2
 hccp 7 channel-switch 2 uc31 wavecom-hd 192.168.1.2 7 192.168.1.4 15
 hccp 7 protect 3 192.168.1.9
 hccp 7 channel-switch 3 rfsw2b rfswitch-group 192.168.1.6 88880800 3
 hccp 7 channel-switch 3 uc32 wavecom-hd 192.168.1.2 7 192.168.1.3 7
 hccp 7 protect 4 192.168.1.10
 hccp 7 channel-switch 4 rfsw2b rfswitch-group 192.168.1.6 88880800 4
 hccp 7 channel-switch 4 uc32 wavecom-hd 192.168.1.2 7 192.168.1.3 15
 hccp 7 timers 666 2000
!
interface Cable6/1
 hccp 8 protect 1 192.168.1.7
 hccp 8 channel-switch 1 rfsw2b rfswitch-group 192.168.1.6 22220200 1
 hccp 8 channel-switch 1 uc31 wavecom-hd 192.168.1.2 8 192.168.1.4 8
 hccp 8 protect 2 192.168.1.8
 hccp 8 channel-switch 2 rfsw2b rfswitch-group 192.168.1.6 22220200 2
 hccp 8 channel-switch 2 uc31 wavecom-hd 192.168.1.2 8 192.168.1.4 16
 hccp 8 protect 3 192.168.1.9
 hccp 8 channel-switch 3 rfsw2b rfswitch-group 192.168.1.6 22220200 3
 hccp 8 channel-switch 3 uc32 wavecom-hd 192.168.1.2 8 192.168.1.3 8
 hccp 8 protect 4 192.168.1.10
 hccp 8 channel-switch 4 rfsw2b rfswitch-group 192.168.1.6 22220200 4
 hccp 8 channel-switch 4 uc32 wavecom-hd 192.168.1.2 8 192.168.1.3 16
 hccp 8 timers 666 2000
!
router eigrp 2500
 network 10.11.12.0 0.0.0.255
 network 10.11.13.0 0.0.0.255
 network 192.168.1.0
 network 192.168.3.0
 network 192.168.5.0
 no auto-summary
 no eigrp log-neighbor-changes
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.1.254
ip route 192.168.1.0 255.255.255.0 FastEthernet0/0
ip route 192.168.2.0 255.255.255.0 FastEthernet0/1
no ip http server
!
cdp run
!
snmp-server community private RW
snmp-server community public RO
snmp-server enable traps tty
snmp-server enable traps cable
snmp-server manager
alias exec shb show hccp brief
alias exec shd show hccp detail
alias exec scm show cable modem
alias exec scr show cable modem remote

Escenario 2

Configuraciones de muestra de la Alta disponibilidad con dos Switches RF (configuración 3x10) en 4+1 modos, cinco VXR, y veinte linecards MC28U.

El diseño físico se muestra en el cuadro 1, pero ignora el upconverters en el top. Refiera a telegrafiar el Cisco RF Switch al uBR7246VXR de Cisco para un documento del cableado que utilice el linecards 28C. El cableado para el linecards MC28U consiste en un conjunto de diez cables que vayan de cada linecard a cada encabezado del RF Switch. Refiera al documento HA que pertenece a esta solución N+1.

El este empilar de la comprobación se asume, con las asignaciones IP que comienzan con 192.168.1.5 en el top y continúan abajo. Porque estará en el modo 4+1, el RF Switch 1 se considera ser dos Switches: a y b, donde está los slots a 1 a 4 y b es el RF Switch 2 de los slots 5 a 8. también se considera dos Switches: a y B.

Configuración de trabajo VXR1
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname "WorkingVXR1"
!
boot system disk0:ubr7200-ik8s-mz.BC....
no logging console
enable secret 5 $1$5YHG$mquxbcqzFoUUKhp/c9WT4/
!
cab modem remote-query 10 public

!--- This is an easy way to track modem transmit and receive levels, especially after a
!--- failover. You might want to increase the time period or remove this command, after
!--- you have confirmed that everything is OK.

cable modulation-profile 41 request 0 16 0 8 qpsk scrambler 152 no-diff 64 fixed
cable modulation-profile 41 initial 5 34 0 48 qpsk scrambler 152 no-diff 128 fixed
cable modulation-profile 41 station 5 34 0 48 qpsk scrambler 152 no-diff 128 fixed
cable modulation-profile 41 short 3 78 35 25 qpsk scrambler 152 no-diff 100 short
cable modulation-profile 41 long 9 232 0 137 qpsk scrambler 152 no-diff 80 short
cable modulation-profile 42 request 0 16 0 8 qpsk scrambler 152 no-diff 64 fixed
cable modulation-profile 42 initial 5 34 0 48 qpsk scrambler 152 no-diff 128 fixed
cable modulation-profile 42 station 5 34 0 48 qpsk scrambler 152 no-diff 128 fixed
cable modulation-profile 42 short 3 78 17 10 16qam scrambler 152 no-diff 136 short
cable modulation-profile 42 long 9 232 0 77 16qam scrambler 152 no-diff 216 short
no cable qos permission create
no cable qos permission update
cable qos permission modems
no cable clock source-midplane
no cable clock force primary
no cable clock force secondary
!
cable config-file docsis.cm
 frequency 453000000
 service-class 1 max-upstream 10000
 service-class 1 max-downstream 10000
 service-class 1 max-burst 1522
!
ip subnet-zero
ip cef
!
ip name-server 171.68.226.120
!
ip dhcp pool MODEMS1
   network 192.168.3.0 255.255.255.0
   bootfile docsis.cm
   next-server 192.168.3.5
   default-router 192.168.3.5
   option 7 ip 192.168.3.5
   option 4 ip 192.168.3.5
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp pool PC
   network 10.11.12.0 255.255.255.0
   default-router 10.11.12.1
   dns-server 171.68.226.120
   lease 10 1 11
!
packetcable element_id 35417
!
interface FastEthernet0/0
 ip address 192.168.1.7 255.255.255.0
 no keepalive
 speed auto
 full-duplex

!--- This interface is used for HCCP traffic.

!
interface FastEthernet0/1
 ip address 192.168.2.7 255.255.255.0
 keepalive 1

!--- This is set to 1 second so that, if the cable is disconnected, this interface
!--- will failover within 3 seconds.

 speed auto
 full-duplex
!
interface Cable3/0
 ip address 10.11.12.1 255.255.255.0 secondary
 ip address 192.168.3.5 255.255.255.0
 load-interval 30
 cable dynamic-secret mark nocrypt
 cable map-advance dynamic 500 1000
 keepalive 1

!--- The keepalive time is in seconds, and the default is 10 seconds for HCCP code.

 cable downstream channel-id 0
 cable bundle 1 master

!--- Interface bundling is supported, as are subinterfaces.
!--- Note: Bundles failover together.

 cable downstream annex B
 cable downstream modulation 256qam
 cable downstream interleave-depth 32
 no cable downstream rf-shutdown
 cable downstream frequency 453000000

!--- This is the DS frequency, which used to be informational only when you are using
!--- an external UPx. This must be set when using the MC28U cards with internal UPxs.

 cable upstream 0 frequency 24000000

!--- If you are doing dense mode combining, the US frequencies must be different.
!--- If no two US ports are shared, the same frequency can be used.

 cable upstream 0 ingress-noise-cancellation 200
 cable upstream 0 power-level 0
 cable upstream 0 channel-width 3200000 3200000
 cable upstream 0 minislot-size 4
 cable upstream 0 fragment-force 3500 3
 cable upstream 0 range-backoff 2 6
 cable upstream 0 data-backoff 3 5
 cable upstream 0 modulation-profile 42
 no cable upstream 0 shutdown
 cable dhcp-giaddr policy

!--- This tells the CMs to get an IP address from the primary scope, and it tells the
!--- CPE to use the secondary scope.

 hccp 1 working 1

!--- This is the Working first group, member 1.

 hccp 1 channel-switch 1 rfsw1a rfswitch-group 192.168.1.5 44440400 1

!--- This is the IP address of the Switch, and it is protecting member 1 in the
!--- left side of Switch slot 1.

 hccp 1 track FastEthernet0/1

!--- Tracking is enabled for the egress port, in the event that the WAN-backhaul is
!--- disrupted. This cable interface will failover to the Protect.

 hccp 1 reverttime 120

!--- This is the time in minutes (plus a 2 minute suspend) for the card to switch back
!--- to normal mode, if the fault has cleared. If there is a fault on the Protect card,
!--- then it will revert back after the suspend time, and it will not wait for the full
!--- revert time.

!
interface Cable3/1
 hccp 2 working 1
 hccp 2 channel-switch 1 rfsw1a rfswitch-group 192.168.1.5 11110100 1

!--- This is the IP address of the Switch, and it is protecting member 1 in the
!--- right side of Switch slot 1.

 hccp 2 reverttime 120
!
interface Cable4/0
 hccp 3 working 1
 hccp 3 channel-switch 1 rfsw1b rfswitch-group 192.168.1.5 88880800 1

!--- This is the IP address of the Switch, and it is protecting member 1 in the
!--- left side of Switch slot 5. Because the RF Switch is in 4+1 mode, slot 5 is
!--- considered to be slot 1 again.

 hccp 3 reverttime 120
!
interface Cable 4/1
 hccp 4 working 1
 hccp 4 channel-switch 1 rfsw1b rfswitch-group 192.168.1.5 22220200 1

!--- This is the IP address of the Switch, and it is protecting member 1 in the
!--- right side of Switch slot 5. Because the RF Switch is in 4+1 mode, slot 5 is
!--- considered to be slot 1 again.

 hccp 4 reverttime 120
!
interface Cable5/0
 hccp 5 working 1
 hccp 5 channel-switch 1 rfsw2a rfswitch-group 192.168.1.6 44440400 1
 hccp 5 reverttime 120
!
interface Cable 5/1
 hccp 6 working 1
 hccp 6 channel-switch 1 rfsw2a rfswitch-group 192.168.1.6 11110100 1
 hccp 6 reverttime 120
!
interface Cable 6/0
 hccp 7 working 1
 hccp 7 channel-switch 1 rfsw2b rfswitch-group 192.168.1.6 88880800 1
 hccp 7 reverttime 120
!
interface Cable 6/1
 hccp 8 working 1
 hccp 8 channel-switch 1 rfsw2b rfswitch-group 192.168.1.6 22220200 1
 hccp 8 reverttime 120
!
router eigrp 2500
 network 10.11.12.0 0.0.0.255
 network 192.168.1.0
 network 192.168.3.0
 no auto-summary
 no eigrp log-neighbor-changes

!--- Open Shortest Path First (OSPF) may be the best routing protocol, with its new
!--- fast-hellos.

ip classless
ip route 0.0.0.0 0.0.0.0 192.168.1.254
ip route 192.168.1.0 255.255.255.0 FastEthernet0/0
ip route 192.168.2.0 255.255.255.0 FastEthernet0/1
no ip http server
!
cdp run
!
snmp-server community private RW

!--- This does not affect the HCCP communications between the Switch and the VXR, but
!--- it must be set to Private on the RF Switch.

snmp-server community public RO
snmp-server enable traps tty
snmp-server manager
tftp-server disk0:
tftp-server disk1:
tftp-server disk1:rfsw250-fl-1935030e
tftp-server disk1:rfsw250-bf-1935022d
alias exec shb show hccp brief
alias exec shd show hccp detail
alias exec scm show cable modem
alias exec scr show cable modem remote
alias exec sm show cab modu
alias exec sch show cab hop
alias exec sc300 show cont c3/0 u0
alias exec sint300 show int c3/0 u0
alias exec scs show cable spec

Proteja las configuraciones de VXR
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname "ProtectVXR"
!
boot system disk0:ubr7200-ik8s-mz.BC.28July03
no logging console
enable secret 5 $1$5YHG$mquxbcqzFoUUKhp/c9WT4/
!
cab modem remote-query 10 public
cable modulation-profile 41 request 0 16 0 8 qpsk scrambler 152 no-diff 64 fixed
cable modulation-profile 41 initial 5 34 0 48 qpsk scrambler 152 no-diff 128 fixed
cable modulation-profile 41 station 5 34 0 48 qpsk scrambler 152 no-diff 128 fixed
cable modulation-profile 41 short 3 78 35 25 qpsk scrambler 152 no-diff 100 short
cable modulation-profile 41 long 9 232 0 137 qpsk scrambler 152 no-diff 80 short
cable modulation-profile 42 request 0 16 0 8 qpsk scrambler 152 no-diff 64 fixed
cable modulation-profile 42 initial 5 34 0 48 qpsk scrambler 152 no-diff 128 fixed
cable modulation-profile 42 station 5 34 0 48 qpsk scrambler 152 no-diff 128 fixed
cable modulation-profile 42 short 3 78 17 10 16qam scrambler 152 no-diff 136 short
cable modulation-profile 42 long 9 232 0 77 16qam scrambler 152 no-diff 216 short

!--- Be sure to pre-configure all global configurations on the Protect, such as
!--- modulation profiles, spectrum groups, load balancing, and so forth.

no cable qos permission create
no cable qos permission update
cable qos permission modems
no cable clock source-midplane
no cable clock force primary
no cable clock force secondary
!
cable config-file docsis.cm
 frequency 453000000
 service-class 1 max-upstream 10000
 service-class 1 max-downstream 10000
 service-class 1 max-burst 1522
!
ip subnet-zero
ip cef
!
ip name-server 171.68.226.120
!
ip dhcp pool MODEMS1
   network 192.168.3.0 255.255.255.0
   bootfile docsis.cm
   next-server 192.168.3.5
   default-router 192.168.3.5
   option 7 ip 192.168.3.5
   option 4 ip 192.168.3.5
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp pool PC
   network 10.11.12.0 255.255.255.0
   default-router 10.11.12.1
   dns-server 171.68.226.120
   lease 10 1 11
!
packetcable element_id 35417
!
interface FastEthernet0/0
 ip address 192.168.1.11 255.255.255.0
 no keepalive
 speed auto
 full-duplex
 no cdp enable

!--- This interface is used for HCCP traffic.

!
interface FastEthernet0/1
 ip address 192.168.2.11 255.255.255.0
 keepalive 1
 speed auto
 full-duplex
 no cdp enable
!
interface Cable3/0
 no ip address

!--- There is no need to set the IP address, because it will come from the Working card
!--- via SNMP.

 no keepalive

!--- This defaults to 10 seconds with the N+1 Cisco IOS code, but it is recommended that
!--- you disable it on the Protect interface or set it to a relatively high value.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32

!--- The DS modulation, annex mode, and interleave must be pre-configured and must be 
!--- the same on the Protect and on the Working of the same group.

 no shut

!--- The interface must be activated to start HCCP functionality. Do this last.

 cable upstream 0 shutdown

!--- This will automatically become "no shut" when a failover occurs.

 hccp 1 protect 1 192.168.1.7

!--- This is the Protect for the first group. Remember to configure the Protect
!--- interface(s) last, after the Working interfaces are configured. This is the HCCP
!--- first group, and it is protecting member 1 with member 1’s FE IP address.

 hccp 1 channel-switch 1 rfsw1a rfswitch-group 192.168.1.5 44440400 1

!--- This is the IP address of the Switch, and it is protecting member 1, which has a
!--- bitmap of 44440400 in Switch slot 1.

 hccp 1 protect 2 192.168.1.8

!--- This is the HCCP first group, and it is protecting member 2 with its IP address.

 hccp 1 channel-switch 2 rfsw1a rfswitch-group 192.168.1.5 44440400 2
 hccp 1 protect 3 192.168.1.9
 hccp 1 channel-switch 3 rfsw1a rfswitch-group 192.168.1.5 44440400 3
 hccp 1 protect 4 192.168.1.10
 hccp 1 channel-switch 4 rfsw1a rfswitch-group 192.168.1.5 44440400 4
 hccp 1 timers 666 2000

!--- hccp 1 timers <hellotime> <holdtime>
!--- This is for inter-chassis communication.

!
interface Cable3/1
 hccp 2 protect 1 192.168.1.7
 hccp 2 channel-switch 1 rfsw1a rfswitch-group 192.168.1.5 11110100 1
 hccp 2 protect 2 192.168.1.8
 hccp 2 channel-switch 2 rfsw1a rfswitch-group 192.168.1.5 11110100 2
 hccp 2 protect 3 192.168.1.9
 hccp 2 channel-switch 3 rfsw1a rfswitch-group 192.168.1.5 11110100 3
 hccp 2 protect 4 192.168.1.10
 hccp 2 channel-switch 4 rfsw1a rfswitch-group 192.168.1.5 11110100 4
 hccp 2 timers 666 2000
!
interface Cable4/0
 hccp 3 protect 1 192.168.1.7
 hccp 3 channel-switch 1 rfsw1b rfswitch-group 192.168.1.5 88880800 1
 hccp 3 protect 2 192.168.1.8
 hccp 3 channel-switch 2 rfsw1b rfswitch-group 192.168.1.5 88880800 2
 hccp 3 protect 3 192.168.1.9
 hccp 3 channel-switch 3 rfsw1b rfswitch-group 192.168.1.5 88880800 3
 hccp 3 protect 4 192.168.1.10
 hccp 3 channel-switch 4 rfsw1b rfswitch-group 192.168.1.5 88880800 4
 hccp 3 timers 666 2000
!
interface Cable4/1
 hccp 4 protect 1 192.168.1.7
 hccp 4 channel-switch 1 rfsw1b rfswitch-group 192.168.1.5 22220200 1
 hccp 4 protect 2 192.168.1.8
 hccp 4 channel-switch 2 rfsw1b rfswitch-group 192.168.1.5 22220200 2
 hccp 4 protect 3 192.168.1.9
 hccp 4 channel-switch 3 rfsw1b rfswitch-group 192.168.1.5 22220200 3
 hccp 4 protect 4 192.168.1.10
 hccp 4 channel-switch 4 rfsw1b rfswitch-group 192.168.1.5 22220200 4
 hccp 4 timers 666 2000
!
interface Cable5/0
 hccp 5 protect 1 192.168.1.7
 hccp 5 channel-switch 1 rfsw2a rfswitch-group 192.168.1.6 44440400 1
 hccp 5 protect 2 192.168.1.8
 hccp 5 channel-switch 2 rfsw2a rfswitch-group 192.168.1.6 44440400 2
 hccp 5 protect 3 192.168.1.9
 hccp 5 channel-switch 3 rfsw2a rfswitch-group 192.168.1.6 44440400 3
 hccp 5 protect 4 192.168.1.10
 hccp 5 channel-switch 4 rfsw2a rfswitch-group 192.168.1.6 44440400 4
 hccp 5 timers 666 2000
!
interface Cable5/1
 hccp 6 protect 1 192.168.1.7
 hccp 6 channel-switch 1 rfsw2a rfswitch-group 192.168.1.6 11110100 1
 hccp 6 protect 2 192.168.1.8
 hccp 6 channel-switch 2 rfsw2a rfswitch-group 192.168.1.6 11110100 2
 hccp 6 protect 3 192.168.1.9
 hccp 6 channel-switch 3 rfsw2a rfswitch-group 192.168.1.6 11110100 3
 hccp 6 protect 4 192.168.1.10
 hccp 6 channel-switch 4 rfsw2a rfswitch-group 192.168.1.6 11110100 4
 hccp 6 timers 666 2000
!
interface Cable6/0
 hccp 7 protect 1 192.168.1.7
 hccp 7 channel-switch 1 rfsw2b rfswitch-group 192.168.1.6 88880800 1
 hccp 7 protect 2 192.168.1.8
 hccp 7 channel-switch 2 rfsw2b rfswitch-group 192.168.1.6 88880800 2
 hccp 7 protect 3 192.168.1.9
 hccp 7 channel-switch 3 rfsw2b rfswitch-group 192.168.1.6 88880800 3
 hccp 7 protect 4 192.168.1.10
 hccp 7 channel-switch 4 rfsw2b rfswitch-group 192.168.1.6 88880800 4
 hccp 7 timers 666 2000
!
interface Cable6/1
 hccp 8 protect 1 192.168.1.7
 hccp 8 channel-switch 1 rfsw2b rfswitch-group 192.168.1.6 22220200 1
 hccp 8 protect 2 192.168.1.8
 hccp 8 channel-switch 2 rfsw2b rfswitch-group 192.168.1.6 22220200 2
 hccp 8 protect 3 192.168.1.9
 hccp 8 channel-switch 3 rfsw2b rfswitch-group 192.168.1.6 22220200 3
 hccp 8 protect 4 192.168.1.10
 hccp 8 channel-switch 4 rfsw2b rfswitch-group 192.168.1.6 22220200 4
 hccp 8 timers 666 2000
!
router eigrp 2500
 network 10.11.12.0 0.0.0.255
 network 10.11.13.0 0.0.0.255
 network 192.168.1.0
 network 192.168.3.0
 network 192.168.5.0
 no auto-summary
 no eigrp log-neighbor-changes

!--- OSPF may be the best routing protocol, with its new fast-hellos.

!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.1.254
ip route 192.168.1.0 255.255.255.0 FastEthernet0/0
ip route 192.168.2.0 255.255.255.0 FastEthernet0/1
no ip http server
!
cdp run
!
snmp-server community private RW
snmp-server community public RO
snmp-server enable traps tty
snmp-server enable traps cable
snmp-server manager
alias exec shb show hccp brief
alias exec shd show hccp detail
alias exec scm show cable modem
alias exec scr show cable modem remote

Escenario 3

configuración de muestra del uBR10K N+1 con el linecards MC28C.

Cuadro 2 – Belden 1855A (coaxil mini-RG-59) con f o los conectores BNC

/image/gif/paws/49776/ha_mc5x20_b.gif

configuración uBR10k
uBR10012-1# show run

Current configuration : 8567 bytes
!
version 12.2
no parser cache
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname uBR10k
!
boot system flash slot0: ubr10k-k8p6-mz.122-4.BC1b
logging rate-limit console all 10 except critical
enable secret 5 $1$.Dvy$fcPOhshUNjyfePH73FHRG.
!
no cable qos permission create
no cable qos permission update
cable qos permission modems
cable time-server
!
cable config-file docsis.cm
 frequency 453000000
 service-class 1 max-upstream 10000
 service-class 1 max-downstream 10000
 service-class 1 max-burst 1522
!
redundancy
  main-cpu
    auto-sync standard
facility-alarm intake-temperature major 49
facility-alarm intake-temperature minor 40
facility-alarm core-temperature major 53
facility-alarm core-temperature minor 45
card 1/0 1gigethernet-1
card 1/1 2cable-tccplus
card 2/0 1gigethernet-1
card 2/1 2cable-tccplus
card 5/0 2cable-mc28c
card 5/1 2cable-mc28c
card 6/0 2cable-mc28c
card 6/1 2cable-mc28c
card 7/0 2cable-mc28c
card 7/1 2cable-mc28c
card 8/0 2cable-mc28c
card 8/1 2cable-mc28c
ip subnet-zero
ip host rfswitch 2001 10.10.10.1

!--- This is set for console access from the 10K to the Switch. The IP address is for
!--- Loopback0.

ip dhcp pool MODEMS1
   network 172.25.1.0 255.255.255.0
   bootfile docsis.cm
   next-server 172.25.1.1
   default-router 172.25.1.1
   option 7 ip 172.25.1.1
   option 4 ip 172.25.1.1
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp pool MODEMS2
   network 172.25.2.0 255.255.255.0
   bootfile docsis.cm
   next-server 172.25.2.1
   default-router 172.25.2.1
   option 7 ip 172.25.2.1
   option 4 ip 172.25.2.1
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp-client network-discovery informs 2 discovers 2 period 15

!--- An internal DHCP server was used for testing, instead of external servers (cable
!--- helper, Time-of-Day [ToD], TFTP, and so forth). External servers are recommended
!--- in a "real" production network.

!
interface Loopback0
 ip address 10.10.10.1 255.255.255.252
!
interface FastEthernet0/0/0
 ip address 10.97.1.8 255.255.255.0
 ip rip receive version 2
 no ip split-horizon
 no keepalive
!
interface GigabitEthernet1/0/0
 no ip address
 negotiation auto
!
interface GigabitEthernet2/0/0
 no ip address
 negotiation auto
!
interface Cable5/1/0

!--- This is the Protect for the first group. Remember to configure the Protect
!--- interface(s) last, after the Working interfaces are configured.

 no ip address

!--- There is no need to set the IP address because it will come from the Working card
!--- via SNMP.

 no keepalive

!--- This defaults to 10 seconds with the N+1 Cisco IOS code, but it is recommended
!--- that you disable it on the Protect interface or set it to a relatively high value.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32

!--- The DS modulation, annex mode, and interleave must be same on the Protect and on
!--- the Working of the same group.

 cable upstream 0 shutdown

!--- This will automatically become "no shut" when a failover occurs.

 cable upstream 1 shutdown
 cable upstream 2 shutdown
 cable upstream 3 shutdown
 cable dhcp-giaddr policy
 hccp 1 protect 1 10.10.10.1

!--- This is the HCCP first group, and it is protecting member 1 with member 1’s FE IP
!--- address. If it is intra-chassis, you can use the Loopback0 IP address.

 hccp 1 channel-switch 1 uc wavecom-hd 10.97.1.21 2 10.97.1.21 16

!--- This is the IP address of the upconverter, and it is module 2 (B) that is backing
!--- module 16 (P) of the upconverter. This shows that one upconverter could have a
!--- module that backs up a module in a different chassis with a different IP address,
!--- if need be. If this statement is not present when you are using Cisco IOS Software
!--- Release 15(BC2) or later, then IF-Muting is assumed, and an external upconverter
!--- with SNMP capability is not needed.

 hccp 1 channel-switch 1 rfswitch rfswitch-group 10.97.1.20 AA200000 1

!--- This is the IP address of the Switch, and it is protecting member 1, which has a
!--- bitmap of AA200000 in Switch slot 1.

 hccp 1 protect 2 10.10.10.1

!--- This is the HCCP first group, and it is protecting member 2 with its IP address.

 hccp 1 channel-switch 2 uc wavecom-hd 10.97.1.21 2 10.97.1.21 14

!--- This is the IP address of the upconverter, and it is module 2 (B) that is backing
!--- module 14 (N).

 hccp 1 channel-switch 2 rfswitch rfswitch-group 10.97.1.20 AA200000 2

!--- This is the IP address of the Switch, and it is protecting member 2, with a bitmap
!--- of AA200000 in Switch slot 2.

 hccp 1 protect 3 10.10.10.1
 hccp 1 channel-switch 3 uc wavecom-hd 10.97.1.21 2 10.97.1.21 12
 hccp 1 channel-switch 3 rfswitch rfswitch-group 10.97.1.20 AA200000 3
 hccp 1 protect 4 10.10.10.1
 hccp 1 channel-switch 4 uc wavecom-hd 10.97.1.21 2 10.97.1.21 10
 hccp 1 channel-switch 4 rfswitch rfswitch-group 10.97.1.20 AA200000 4
 hccp 1 protect 5 10.10.10.1
 hccp 1 channel-switch 5 uc wavecom-hd 10.97.1.21 2 10.97.1.21 8
 hccp 1 channel-switch 5 rfswitch rfswitch-group 10.97.1.20 AA200000 5
 hccp 1 protect 6 10.10.10.1
 hccp 1 channel-switch 6 uc wavecom-hd 10.97.1.21 2 10.97.1.21 6
 hccp 1 channel-switch 6 rfswitch rfswitch-group 10.97.1.20 AA200000 6
 hccp 1 protect 7 10.10.10.1
 hccp 1 channel-switch 7 uc wavecom-hd 10.97.1.21 2 10.97.1.21 4
 hccp 1 channel-switch 7 rfswitch rfswitch-group 10.97.1.20 AA200000 7
 hccp 1 timers 5000 15000

!--- hccp 1 timers <hellotime> <holdtime>
!--- This is for inter-chassis communication, so set high for the 10K.

!
interface Cable5/1/1

!--- This is the Protect for the second group.

 no ip address
 no keepalive
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable upstream 0 shutdown
 cable upstream 1 shutdown
 cable upstream 2 shutdown
 cable upstream 3 shutdown
 cable dhcp-giaddr policy
!
 hccp 2 protect 1 10.10.10.1
 hccp 2 channel-switch 1 uc wavecom-hd 10.97.1.21 1 10.97.1.21 15
 hccp 2 channel-switch 1 rfswitch rfswitch-group 10.97.1.20 55100000 1

!--- Because this MAC domain is on right side of header, the bitmap in hexadecimal code
!--- is 55100000.

 hccp 2 protect 2 10.10.10.1
 hccp 2 channel-switch 2 uc wavecom-hd 10.97.1.21 1 10.97.1.21 13
 hccp 2 channel-switch 2 rfswitch rfswitch-group 10.97.1.20 55100000 2
 hccp 2 protect 3 10.10.10.1
 hccp 2 channel-switch 3 uc wavecom-hd 10.97.1.21 1 10.97.1.21 11
 hccp 2 channel-switch 3 rfswitch rfswitch-group 10.97.1.20 55100000 3
 hccp 2 protect 4 10.10.10.1
 hccp 2 channel-switch 4 uc wavecom-hd 10.97.1.21 1 10.97.1.21 9
 hccp 2 channel-switch 4 rfswitch rfswitch-group 10.97.1.20 55100000 4
 hccp 2 protect 5 10.10.10.1
 hccp 2 channel-switch 5 uc wavecom-hd 10.97.1.21 1 10.97.1.21 7
 hccp 2 channel-switch 5 rfswitch rfswitch-group 10.97.1.20 55100000 5
 hccp 2 protect 6 10.10.10.1
 hccp 2 channel-switch 6 uc wavecom-hd 10.97.1.21 1 10.97.1.21 5
 hccp 2 channel-switch 6 rfswitch rfswitch- group 10.97.1.20 55100000 6
 hccp 2 protect 7 10.10.10.1
 hccp 2 channel-switch 7 uc wavecom-hd 10.97.1.21 1 10.97.1.21 3
 hccp 2 channel-switch 7 rfswitch rfswitch-group 10.97.1.20 55100000 7
 hccp 2 timers 5000 15000
!
interface Cable8/1/0

!--- This is the Working for the first group.

 ip address 10.192.5.1 255.255.255.0 secondary
 ip address 172.25.1.1 255.255.255.0

!--- Interface bundling is supported, as are subinterfaces.

 ip rip send version 2
 ip rip receive version 2
 keepalive 1

!--- The keepalive time is in seconds, and the default is 10 seconds for HCCP code.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000

!--- This is the DS frequency, which used to be informational only when you are using
!--- an external upconverter. This must be set when doing N+1, so the Protect
!--- upconverter knows what frequency to use.

 cable upstream 0 frequency 24000000

!--- If you are doing dense mode combining, the US frequencies must be different.
!--- If no two US ports are shared, the same frequency can be used.

 cable upstream 0 power-level 0
 no cable upstream 0 shutdown
 cable upstream 1 power-level 0
 cable upstream 1 shutdown
 cable upstream 2 power-level 0
 cable upstream 2 shutdown
 cable upstream 3 power-level 0
 cable upstream 3 shutdown
 cable dhcp-giaddr policy

!--- This tells the CMs to get an IP address from the primary scope, and it tells the
!--- CPE to use the secondary scope.

 hccp 1 working 1

!--- This is Working member 1 of HCCP Group 1.

 hccp 1 channel-switch 1 uc wavecom-hd 10.97.1.21 2 10.97.1.21 16

!--- This is the IP address of the upconverter, and it is module 2 (B) that is backing
!--- module 16 (P).

 hccp 1 channel-switch 1 rfswitch rfswitch-group 10.97.1.20 AA200000 1

!--- This is the IP address of the Switch and of member 1, which has a bitmap of
!--- AA200000 in Switch slot 1.

 hccp 1 reverttime 120

!--- This is the time in minutes (plus a 2 minute suspend) for the card to switch back
!--- to normal mode, if the fault has cleared. If a fault is initiated by a keepalive
!--- and you have a fault on the Protect card, then it will revert back after the
!--- suspend time, and it will not wait for the full revert time.

!
interface Cable8/1/1

!--- This is the Working interface for the second HCCP group.

 ip address 10.192.5.1 255.255.255.0 secondary
 ip address 172.25.2.1 255.255.255.0
 ip rip send version 2
 ip rip receive version 2
 keepalive 1
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000
 cable upstream 0 frequency 24000000
 cable upstream 0 power-level 0
 no cable upstream 0 shutdown
 cable upstream 1 power-level 0
 cable upstream 1 shutdown
 cable upstream 2 power-level 0
 cable upstream 2 shutdown
 cable upstream 3 power-level 0
 cable upstream 3 shutdown
 cable dhcp-giaddr policy
 hccp 2 working 1

!--- This is Working member 1 of HCCP Group 2.

 hccp 2 channel-switch 1 uc wavecom-hd 10.97.1.21 1 10.97.1.21 15
 hccp 2 channel-switch 1 rfswitch rfswitch-group 10.97.1.20 55100000 1

!--- This is the IP address of the Switch and of member 1 of Group 2, which has a
!--- bitmap of 55100000 in Switch slot 1.

 hccp 2 reverttime 120
!
ip classless
no ip http server
!
no cdp run
snmp-server community private RW

!--- This does not affect the HCCP communications between the upconverter, the Switch,
!--- and the 10K.

snmp-server enable traps cable
no cdp run
snmp-server manager
tftp-server server
tftp-server ios.cf alias ios.cf
!
line con 0
 logging synchronous
line aux 0
 no exec
 transport input all

!--- The previous three lines are used to console from the Auxiliary port of the 10K to
!--- the Switch.

line vty 0 4
 session-timeout 400
 password xx
 login
endBuilding configuration...

Situación 4

Configuración de muestra para el linecards 5x20 en el modo 8+1.

Cuadro 3 – Coaxil del Belden mini-RG-59 con los conectores MCX

/image/gif/paws/49776/ha_mc5x20_c.gif

configuración uBR10k
uBR10012-1# show run

Current configuration : 8567 bytes
!
version 12.2
no parser cache
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname uBR10k
!
boot system flash slot0: ubr10k-k8p6-mz.122-15.BC1
logging rate-limit console all 10 except critical
enable secret 5 $1$.Dvy$fcPOhshUNjyfePH73FHRG
cable modulation-profile 21 request 0 16 0 22 qpsk scrambler 152 no-diff 32 fixed
cable modulation-profile 21 initial 5 34 0 48 qpsk scrambler 152 no-diff 64 fixed
cable modulation-profile 21 station 5 34 0 48 qpsk scrambler 152 no-diff 64 fixed
cable modulation-profile 21 short 3 76 12 22 qpsk scrambler 152 no-diff 64 shortened
cable modulation-profile 21 long 7 231 0 22 qpsk scrambler 152 no-diff 64 shortened

!--- Advanced time division multiplex access (ATDMA) Cisco IOS has different
!--- modulation profiles and requirements.

!
no cable qos permission create
no cable qos permission update
cable qos permission modems
cable time-server
!
cable config-file docsis.cm
 frequency 453000000
 service-class 1 max-upstream 10000
 service-class 1 max-downstream 10000
 service-class 1 max-burst 1522
!
redundancy
  main-cpu
    auto-sync standard
facility-alarm intake-temperature major 49
facility-alarm intake-temperature minor 40
facility-alarm core-temperature major 53
facility-alarm core-temperature minor 45
card 1/0 1gigethernet-1
card 1/1 2cable-tccplus
card 2/0 1gigethernet-1
card 2/1 2cable-tccplus
card 5/0 5cable-mc520s-d
card 5/1 5cable-mc520s-d
card 6/0 5cable-mc520s-d
card 6/1 5cable-mc520s-d
card 7/0 5cable-mc520s-d
card 7/1 5cable-mc520s-d
card 8/0 5cable-mc520s-d
card 8/1 5cable-mc520s-d
ip subnet-zero
ip host rfswitch 2001 10.10.10.1

!--- This is set for console access from the 10K to the Switch. The IP address is for
!--- Loopback0.

ip dhcp pool MODEMS1
   network 172.25.1.0 255.255.255.0
   bootfile docsis.cm
   next-server 172.25.1.1
   default-router 172.25.1.1
   option 7 ip 172.25.1.1
   option 4 ip 172.25.1.1
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp pool MODEMS2
   network 172.25.2.0 255.255.255.0
   bootfile docsis.cm
   next-server 172.25.2.1
   default-router 172.25.2.1
   option 7 ip 172.25.2.1
   option 4 ip 172.25.2.1
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp-client network-discovery informs 2 discovers 2 period 15

!--- An internal DHCP server was used for testing instead of external servers (cable
!--- helper, ToD, TFTP, and so forth). External servers are recommended in a "real"
!--- production network.

!
interface Loopback0
 ip address 10.10.10.1 255.255.255.252
!
interface FastEthernet0/0/0
 ip address 10.97.1.8 255.255.255.0
 ip rip receive version 2
 no ip split-horizon
 no keepalive
!
interface GigabitEthernet1/0/0
 no ip address
 negotiation auto
!
interface GigabitEthernet2/0/0
 no ip address
 negotiation auto

!--- This assumes rfsw2 is on the top, as shown in the cable reference guide. Other
!--- interfaces will be the same, except they will have a different member number
!--- for each HCCP group.

interface Cable5/1/0

!--- This is the Protect for the first group. It may be best to configure the Protect
!--- interface(s) last, after the Working interfaces are configured, or keep the
!--- interface "shut" until you are finished with all configurations.

 no ip address

!--- There is no need to set the IP address, because it will come from the Working card
!--- via SNMP.

 no keepalive

!--- This defaults to 10 seconds with the N+1 Cisco IOS code, but it is recommended
!--- that you disable it on the Protect interface or set it to a relatively high value.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32

!--- The DS modulation and interleave must be the same on the Protect and on the
!--- Working of the same group. The Protect interface itself must be "no shut" for
!--- HCCP to activate.

 cable downstream rf-shutdown
 cable upstream 0 shutdown

!--- These will automatically become "no shut" when a failover occurs.

 cable upstream 1 shutdown
 cable upstream 2 shutdown
 cable upstream 3 shutdown
 hccp 1 protect 1 10.10.10.1

!--- This is the HCCP first group, and it is protecting member 1 with member 1’s FE IP
!--- address. If it is intra-chassis, you can use the Loopback0 IP address.

 hccp 1 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 AA200000 1

!--- This is the IP address of the Switch, and it is protecting member 1, which has a
!--- bitmap of AA200000 in Switch slot 1.

 hccp 1 protect 2 10.10.10.1

!--- This is the HCCP first group, and it is protecting member 2 with the loopback IP
!--- address.

 hccp 1 channel-switch 2 rfsw2 rfswitch-group 10.97.1.20 AA200000 2

!--- This is the IP address of the Switch, and it is protecting member 2, with a bitmap
!--- of AA200000 in Switch slot 2.

 hccp 1 protect 3 10.10.10.1
 hccp 1 channel-switch 3 rfsw2 rfswitch-group 10.97.1.20 AA200000 3
 hccp 1 protect 4 10.10.10.1
 hccp 1 channel-switch 4 rfsw2 rfswitch-group 10.97.1.20 AA200000 4
 hccp 1 protect 5 10.10.10.1
 hccp 1 channel-switch 5 rfsw2 rfswitch-group 10.97.1.20 AA200000 5
 hccp 1 protect 6 10.10.10.1
 hccp 1 channel-switch 6 rfsw2 rfswitch-group 10.97.1.20 AA200000 6
 hccp 1 protect 7 10.10.10.1
 hccp 1 channel-switch 7 rfsw2 rfswitch-group 10.97.1.20 AA200000 7

!--- These channel-switch configurations can be copied and pasted into their respective
!--- Working interfaces.

 hccp 1 timers 5000 15000

!--- hccp 1 timers <hellotime> <holdtime>
!--- This is mostly for inter-chassis communication, so set it high for the 10K, as
!--- this can create extra CPU load.

 no hccp 1 revertive
!
interface Cable5/1/1

!--- This is the Protect for the second group.

 no ip address
 no keepalive
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream rf-shutdown
 cable upstream 0 shutdown
 cable upstream 1 shutdown
 cable upstream 2 shutdown
 cable upstream 3 shutdown
!
 hccp 2 protect 1 10.10.10.1
 hccp 2 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 55100000 1

!--- Because this MAC domain is on right side of header, the bitmap in hexadecimal code
!--- is 55100000.

 hccp 2 protect 2 10.10.10.1
 hccp 2 channel-switch 2 rfsw2 rfswitch-group 10.97.1.20 55100000 2
 hccp 2 protect 3 10.10.10.1
 hccp 2 channel-switch 3 rfsw2 rfswitch-group 10.97.1.20 55100000 3
 hccp 2 protect 4 10.10.10.1
 hccp 2 channel-switch 4 rfsw2 rfswitch-group 10.97.1.20 55100000 4
 hccp 2 protect 5 10.10.10.1
 hccp 2 channel-switch 5 rfsw2 rfswitch-group 10.97.1.20 55100000 5
 hccp 2 protect 6 10.10.10.1
 hccp 2 channel-switch 6 rfsw2 rfswitch-group 10.97.1.20 55100000 6
 hccp 2 protect 7 10.10.10.1
 hccp 2 channel-switch 7 rfsw2 rfswitch-group 10.97.1.20 55100000 7
 hccp 2 timers 5000 15000
 no hccp 2 revertive
!
interface Cable5/1/2

!--- This is the Protect for the third group.

 no ip address
 no keepalive
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream rf-shutdown
 cable upstream 0 shutdown
 cable upstream 1 shutdown
 cable upstream 2 shutdown
 cable upstream 3 shutdown
 hccp 3 protect 1 10.10.10.1
 hccp 3 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 00C80000 1
 hccp 3 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 00C00000 1

!--- Because the third MAC domain will traverse both Switches, two statements are
!--- needed. The 00 in front of the bitmaps will be dropped, when the running
!--- configuration is viewed.

 no hccp 3 revertive
!
interface Cable5/1/3

!--- This is the Protect for the fourth group.

 hccp 4 protect 1 10.10.10.1
 hccp 4 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 AA200000 1
 hccp 4 protect 2 10.10.10.1
 hccp 4 channel-switch 2 rfsw1 rfswitch-group 10.97.1.19 AA200000 2
 hccp 4 protect 3 10.10.10.1
 hccp 4 channel-switch 3 rfsw1 rfswitch-group 10.97.1.19 AA200000 3
 hccp 4 protect 4 10.10.10.1
 hccp 4 channel-switch 4 rfsw1 rfswitch-group 10.97.1.19 AA200000 4
 hccp 4 protect 5 10.10.10.1
 hccp 4 channel-switch 5 rfsw1 rfswitch-group 10.97.1.19 AA200000 5
 hccp 4 protect 6 10.10.10.1
 hccp 4 channel-switch 6 rfsw1 rfswitch-group 10.97.1.19 AA200000 6
 hccp 4 protect 7 10.10.10.1
 hccp 4 channel-switch 7 rfsw1 rfswitch-group 10.97.1.19 AA200000 7
 no hccp 4 revertive
!
interface Cable5/1/4

!--- This is the Protect for the fifth group.

 hccp 5 protect 1 10.10.10.1
 hccp 5 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 55100000 1
 hccp 5 protect 2 10.10.10.1
 hccp 5 channel-switch 2 rfsw1 rfswitch-group 10.97.1.19 55100000 2
 hccp 5 protect 3 10.10.10.1
 hccp 5 channel-switch 3 rfsw1 rfswitch-group 10.97.1.19 55100000 3
 hccp 5 protect 4 10.10.10.1
 hccp 5 channel-switch 4 rfsw1 rfswitch-group 10.97.1.19 55100000 4
 hccp 5 protect 5 10.10.10.1
 hccp 5 channel-switch 5 rfsw1 rfswitch-group 10.97.1.19 55100000 5
 hccp 5 protect 6 10.10.10.1
 hccp 5 channel-switch 6 rfsw1 rfswitch-group 10.97.1.19 55100000 6
 hccp 5 protect 7 10.10.10.1
 hccp 5 channel-switch 7 rfsw1 rfswitch-group 10.97.1.19 55100000 7

!--- Output suppressed.

!
interface Cable8/1/0

!--- This is the Working for the first group.

 ip address 10.192.5.1 255.255.255.0 secondary
 ip address 172.25.1.1 255.255.255.0

!--- Interface bundling is supported, as are subinterfaces.

 ip rip send version 2
 ip rip receive version 2
 keepalive 1

!--- The keepalive time is in seconds, and the default is 10 seconds for HCCP code.
!--- Only set this after the modems have stabilized.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000

!--- This is the DS frequency, which must be set for the internal upconverter to
!--- operate.

 cable downstream channel-id 0
 no cable downstream rf-shutdown

!--- This is needed to turn on the DS RF output.

 cable upstream 0 frequency 24000000

!--- If you are doing dense mode combining, the US frequencies must be different.
!--- If no two US ports are shared, the same frequency can be used.

 cable upstream 0 power-level 0
 cable upstream 0 connector 0

!--- This is a new command for virtual interfaces, where USs can be used for different
!--- DS MAC domains.

 cable upstream 0 channel-width 3200000
 cable upstream 0 minislot-size 2
 cable upstream 0 modulation-profile 22
 no cable upstream 0 shutdown

!--- Output suppressed.

 cable dhcp-giaddr policy

!--- This tells the the CMs to get an IP address from the primary scope, and it tells
!--- the CPE to use the secondary scope.

 hccp 1 working 1

!--- This is Working member 1 of HCCP Group 1.

 hccp 1 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 AA200000 1

!--- This is the IP address of the Switch and of member 1, which has a bitmap of
!--- AA200000 in Switch slot 1.

 hccp 1 reverttime 120

!--- This is the time in minutes (plus a 2 minute suspend) for the card to switch back
!--- to normal mode, if the fault has cleared. If a fault is initiated by a keepalive
!--- and you have a fault on the Protect card, then it will revert back after the
!--- suspend time, and it will not wait for the full revert time.

!
interface Cable8/1/1

!--- This is the Working interface for the second HCCP group.

 ip address 10.192.5.1 255.255.255.0 secondary
 ip address 172.25.2.1 255.255.255.0
 ip rip send version 2
 ip rip receive version 2
 keepalive 1
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000
 cable downstream channel-id 1
 no cable downstream rf-shutdown
 cable upstream 0 frequency 24000000
 cable upstream 0 power-level 0
 cable upstream 0 connector 4
 cable upstream 0 channel-width 3200000
 cable upstream 0 minislot-size 22
 cable upstream 0 modulation-profile 2
 no cable upstream 0 shutdown

!--- Output suppressed.

 cable dhcp-giaddr policy
 hccp 2 working 1

!--- This is Working member 1 of HCCP Group 2.

 hccp 2 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 55100000 1

!--- This is the IP address of the Switch and of member 1 of Group 2, which has a
!--- bitmap of 55100000 in Switch slot 1.

 hccp 2 reverttime 120
!
interface Cable8/1/2

!--- This is the Working interface for the third HCCP group.

 ip address 10.192.5.1 255.255.255.0 secondary
 ip address 172.25.3.1 255.255.255.0
 ip rip send version 2
 ip rip receive version 2
 keepalive 1
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000
 cable downstream channel-id 2
 no cable downstream rf-shutdown
 cable upstream 0 frequency 24000000
 cable upstream 0 power-level 0
 cable upstream 0 connector 8
 cable upstream 0 channel-width 3200000
 cable upstream 0 minislot-size 2
 cable upstream 0 modulation-profile 22
 no cable upstream 0 shutdown
 cable dhcp-giaddr policy

!--- Output suppressed.

 hccp 3 working 1

!--- This is Working member 1 of HCCP Group 3.

 hccp 3 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 00c80000 1
 hccp 3 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 00c00000 1
 hccp 3 reverttime 120
!
interface Cable8/1/3

!--- This is the Working interface for the fourth HCCP group.

 hccp 4 working 1
 hccp 4 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 AA200000 1
 hccp 4 reverttime 120
!
interface Cable8/1/4

!--- This is the Working interface for the fifth HCCP group.

 hccp 5 working 1
 hccp 5 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 55100000 1
 hccp 5 reverttime 120
!
ip classless
no ip http server
!
no cdp run
snmp-server community private RW

!--- This does not affect the HCCP communications between the Switch and 10K.

snmp-server enable traps cable
no cdp run
snmp-server manager
tftp-server server
tftp-server ios.cf alias ios.cf
!
alias exec t configure terminal
alias exec scm show cable modem
alias exec scr sh cab mode remote
alias exec shb sh hccp br
alias exec shd sh hccp detail
alias exec shc sh hccp chan
!
line con 0
 logging synchronous
line aux 0
 no exec
 transport input all

!--- The three previous lines are used to console from the Auxiliary port of the 10K
!--- to the Switch.

line vty 0 4
 session-timeout 400
 password xx
 login
endBuilding configuration...

Situación 5

Configuración de muestra para el linecards 5x20 en el modo 4+1 con un RF Switch.

Cuadro 4 – uBR10K con el MC5x20 y 1 RF Switch (4+1)

/image/gif/paws/49776/ha_mc5x20_d.gif

Switch RF

DIRECCIÓN IP 10.1.1.10
Comunidad SNMP Privado
Modo de protección 4
BITMAP Group1 0x44440400
Group2 0x11110100
Group3 0x00005000
Group4 0x0000a080
Group5 0x88880800
Group6 0x22220200

Cuadro 5 – BITMAP

/image/gif/paws/49776/ha_mc5x20_e.gif

La configuración de muestra siguiente está para la Alta disponibilidad 4+1 para cinco indicadores luminosos LED amarillo de la placa muestra gravedad menor del MC5x20 con uno uBR-RFSW en el modo de protección 4+1. El Modo de protección afecta a las BITMAP del Switch y de la configuración del Sistema de terminación del cablemódem (CMTS). Si usted agrega un más 5x20, el asunto debe ser cambiado.

Refiera al cableado en el cableado del Switches del uBR 3x10 RF de Cisco al linecards de la interfaz del cable de Cisco uBR10-MC5X20S/U en un Cisco uBR10012 CMTS.

  1. Tome la encabezado que dice el RF Switch 2 (remate el Switch) y váyase en los slots 1, 2,3, y 4.

  2. Tome la encabezado que dice el RF Switch 1 y el lugar en los slots 5, 6, 7, y 8 del RF Switch 2.

  3. Tome la protección contra el RF Switch 2 y póngala adentro protegen 2.

  4. Tome la protección contra el RF Switch 1 y póngala adentro protegen 1 del RF Switch 2.

  5. Una vez que usted consigue a cinco indicadores luminosos LED amarillo de la placa muestra gravedad menor de trabajo 5x20, la configuración a memoria de imagen debe ser cambiada y las encabezados se deben mover alrededor, a partir de un RF Switch al otro.

    Por ejemplo, la encabezado del slot 5 del RF Switch 2 se moverá a la encabezado del slot1 del RF Switch 1.

La configuración se etiqueta rfswa, pues pertenece a los slots 1 a 4 y su slot de protección respectivo, que es proteja 2. protegen los slots 5 a 8 de 1 cubierta en el RF Switch, y se etiqueta rfswb. En el modo 4+1, los slots 5 a 8 del RF Switch se consideran ser los slots 1 a 4 para los fines de la configuración.

Substituya su dirección IP del RF Switch para la que se muestra en el próximo ejemplo (10.10.10.10).

Configuración en funcionamiento 4+1
interface c7/1/0
hccp 1 working 1
hccp 1 channel-switch 1 rfswa rfswitch-group 10.10.10.10 44440400 1
interface c7/1/1
hccp 2 working 1
hccp 2 channel-switch 1 rfswa rfswitch-group 10.10.10.10 11110100 1
interface c7/1/2
hccp 3 working 1
hccp 3 channel-switch 1 rfswa rfswitch-group 10.10.10.10 00005000 1
hccp 3 channel-switch 1 rfswb rfswitch-group 10.10.10.10 0000a080 1

!--- Prepended 0s will not show up when you execute a show run
!--- command. Do not blindly copy and paste an interface
!--- configuration.

interface c7/1/3
hccp 4 working 1
hccp 4 channel-switch 1 rfswb rfswitch-group 10.10.10.10 88880800 1
interface c7/1/4
hccp 5 working 1
hccp 5 channel-switch 1 rfswb rfswitch-group 10.10.10.10 22220200 1
-------------------------------------------------------------------
interface c6/0/0
hccp 1 working 2
hccp 1 channel-switch 2 rfswa rfswitch-group 10.10.10.10 44440400 2
interface c6/0/1
hccp 2 working 2
hccp 2 channel-switch 2 rfswa rfswitch-group 10.10.10.10 11110100 2
interface c6/0/2
hccp 3 working 2
hccp 3 channel-switch 2 rfswa rfswitch-group 10.10.10.10 00005000 2
hccp 3 channel-switch 2 rfswb rfswitch-group 10.10.10.10 0000a080 2
interface c6/0/3
hccp 4 working 2
hccp 4 channel-switch 2 rfswb rfswitch-group 10.10.10.10 88880800 2
interface c6/0/4
hccp 5 working 2
hccp 5 channel-switch 2 rfswb rfswitch-group 10.10.10.10 22220200 2
-------------------------------------------------------------------
interface c6/1/0
hccp 1 working 3
hccp 1 channel-switch 3 rfswa rfswitch-group 10.10.10.10 44440400 3
interface c6/1/1
hccp 2 working 3
hccp 2 channel-switch 3 rfswa rfswitch-group 10.10.10.10 11110100 3
interface c6/1/2
hccp 3 working 3
hccp 3 channel-switch 3 rfswa rfswitch-group 10.10.10.10 00005000 3
hccp 3 channel-switch 3 rfswb rfswitch-group 10.10.10.10 0000a080 3
interface c6/1/3
hccp 4 working 3
hccp 4 channel-switch 3 rfswb rfswitch-group 10.10.10.10 88880800 3
interface c6/1/4
hccp 5 working 3
hccp 5 channel-switch 3 rfswb rfswitch-group 10.10.10.10 22220200 3
-------------------------------------------------------------------
interface c5/0/0
hccp 1 working 4
hccp 1 channel-switch 4 rfswa rfswitch-group 10.10.10.10 44440400 4
interface c5/0/1
hccp 2 working 4
hccp 2 channel-switch 4 rfswa rfswitch-group 10.10.10.10 11110100 4
interface c5/0/2
hccp 3 working 4
hccp 3 channel-switch 4 rfswa rfswitch-group 10.10.10.10 00005000 4
hccp 3 channel-switch 4 rfswb rfswitch-group 10.10.10.10 0000a080 4
interface c5/0/3
hccp 4 working 4
hccp 4 channel-switch 4 rfswb rfswitch-group 10.10.10.10 88880800 4
interface c5/0/4
hccp 5 working 4
hccp 5 channel-switch 4 rfswb rfswitch-group 10.10.10.10 22220200 4

Proteja las configuraciones de la interfaz
interface c5/1/0
hccp 1 protect 1 10.10.10.1
hccp 1 channel-switch 1 rfswa rfswitch-group 10.10.10.10 44440400 1
hccp 1 protect 2 10.10.10.1
hccp 1 channel-switch 2 rfswa rfswitch-group 10.10.10.10 44440400 2
hccp 1 protect 3 10.10.10.1
hccp 1 channel-switch 3 rfswa rfswitch-group 10.10.10.10 44440400 3
hccp 1 protect 4 10.10.10.1
hccp 1 channel-switch 4 rfswa rfswitch-group 10.10.10.10 44440400 4
-------------------------------------------------------------------
interface c5/1/1
hccp 2 protect 1 10.10.10.1
hccp 2 channel-switch 1 rfswa rfswitch-group 10.10.10.10 11110100 1
hccp 2 protect 2 10.10.10.1
hccp 2 channel-switch 2 rfswa rfswitch-group 10.10.10.10 11110100 2
hccp 2 protect 3 10.10.10.1
hccp 2 channel-switch 3 rfswa rfswitch-group 10.10.10.10 11110100 3
hccp 2 protect 4 10.10.10.1
hccp 2 channel-switch 4 rfswa rfswitch-group 10.10.10.10 11110100 4
-------------------------------------------------------------------
interface c5/1/2
hccp 3 protect 1 10.10.10.1
hccp 3 channel-switch 1 rfswa rfswitch-group 10.10.10.10 00005000 1
hccp 3 channel-switch 1 rfswb rfswitch-group 10.10.10.10 0000a080 1
hccp 3 protect 2 10.10.10.1
hccp 3 channel-switch 2 rfswa rfswitch-group 10.10.10.10 00005000 2
hccp 3 channel-switch 2 rfswb rfswitch-group 10.10.10.10 0000a080 2
hccp 3 protect 3 10.10.10.1
hccp 3 channel-switch 3 rfswa rfswitch-group 10.10.10.10 00005000 3
hccp 3 channel-switch 3 rfswb rfswitch-group 10.10.10.10 0000a080 3
hccp 3 protect 4 10.10.10.1
hccp 3 channel-switch 4 rfswa rfswitch-group 10.10.10.10 00005000 4
hccp 3 channel-switch 4 rfswb rfswitch-group 10.10.10.10 0000a080 4
-------------------------------------------------------------------
interface c5/1/3
hccp 4 protect 1 10.10.10.1
hccp 4 channel-switch 1 rfswb rfswitch-group 10.10.10.10 88880800 1
hccp 4 protect 2 10.10.10.1
hccp 4 channel-switch 2 rfswb rfswitch-group 10.10.10.10 88880800 2
hccp 4 protect 3 10.10.10.1
hccp 4 channel-switch 3 rfswb rfswitch-group 10.10.10.10 88880800 3
hccp 4 protect 4 10.10.10.1
hccp 4 channel-switch 4 rfswb rfswitch-group 10.10.10.10 88880800 4
-------------------------------------------------------------------
interface c5/1/4
hccp 5 protect 1 10.10.10.1
hccp 5 channel-switch 1 rfswb rfswitch-group 10.10.10.10 22220200 1
hccp 5 protect 2 10.10.10.1
hccp 5 channel-switch 2 rfswb rfswitch-group 10.10.10.10 22220200 2
hccp 5 protect 3 10.10.10.1
hccp 5 channel-switch 3 rfswb rfswitch-group 10.10.10.10 22220200 3
hccp 5 protect 4 10.10.10.1
hccp 5 channel-switch 4 rfswb rfswitch-group 10.10.10.10 22220200 4

Estas configuraciones están para las Conmutaciones por falla de la interfaz MAC, pero tienen presente que una HORCA entera ([ASIC] del circuito específico de la aplicación) fallará junta. La parte DS 0 y 1 mismo ASIC, DS 2 y 3 comparte mismo ASIC, y el DS4 está en su propio ASIC. Si una interfaz no tiene HCCP configurado, después no Conmutación por falla, incluso si comparte mismo ASIC.

Si usted configura los hosts máximos por aguas arriba del taxi x y o el conector y del taxi u4, después usted ha configurado un VI (interfaz virtual), también conocido como dominios MAC configurables. Ahora, el linecard entero quiere la Conmutación por falla como conjunto cuando usted tiene cualquier error de la interfaz. Si se borran los comandos del conector, la única forma de deshacer la influencia de la interfaz virtual en las Conmutaciones por falla es recargar al router.

Configuración de muestra 8+1
uBR10012-1# show run

Current configuration : 8567 bytes
!
version 12.2
no parser cache
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname uBR10k
!
boot system flash slot0: ubr10k-k8p6-mz.122-15.BC1
logging rate-limit console all 10 except critical
enable secret 5 $1$.Dvy$fcPOhshUNjyfePH73FHRG
cable modulation-profile 21 request 0 16 0 22 qpsk scrambler 152 no-diff 32 fixed
cable modulation-profile 21 initial 5 34 0 48 qpsk scrambler 152 no-diff 64 fixed
cable modulation-profile 21 station 5 34 0 48 qpsk scrambler 152 no-diff 64 fixed
cable modulation-profile 21 short 3 76 12 22 qpsk scrambler 152 no-diff 64 shortened
cable modulation-profile 21 long 9 232 0 22 qpsk scrambler 152 no-diff 64 shortened
!
no cable qos permission create
no cable qos permission update
cable qos permission modems
cable time-server
!
cable config-file docsis.cm
 frequency 453000000
 service-class 1 max-upstream 10000
 service-class 1 max-downstream 10000
 service-class 1 max-burst 1522
!
redundancy
  main-cpu
    auto-sync standard
facility-alarm intake-temperature major 49
facility-alarm intake-temperature minor 40
facility-alarm core-temperature major 53
facility-alarm core-temperature minor 45
card 1/0 1gigethernet-1
card 1/1 2cable-tccplus
card 2/0 1gigethernet-1
card 2/1 2cable-tccplus
card 5/0 5cable-mc520s-d
card 5/1 5cable-mc520s-d
card 6/0 5cable-mc520s-d
card 6/1 5cable-mc520s-d
card 7/0 5cable-mc520s-d
card 7/1 5cable-mc520s-d
card 8/0 5cable-mc520s-d
card 8/1 5cable-mc520s-d
ip subnet-zero
ip host rfswitch 2001 10.10.10.1

!--- This is set for console access from the 10K to the Switch.
!--- The IP address is for Loopback0.

ip dhcp pool MODEMS1
   network 172.25.1.0 255.255.255.0
   bootfile docsis.cm
   next-server 172.25.1.1
   default-router 172.25.1.1
   option 7 ip 172.25.1.1
   option 4 ip 172.25.1.1
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp pool MODEMS2
   network 172.25.2.0 255.255.255.0
   bootfile docsis.cm
   next-server 172.25.2.1
   default-router 172.25.2.1
   option 7 ip 172.25.2.1
   option 4 ip 172.25.2.1
   option 2 hex 0000.0000
   lease 2 3 4
!
ip dhcp-client network-discovery informs 2 discovers 2 period 15

!--- An internal DHCP server was used for testing instead of external servers
!--- (cable helper, TOD, TFTP, and so forth). External servers are recommended
!--- in a “real” production network.

!
interface Loopback0
 ip address 10.10.10.1 255.255.255.252
!
interface FastEthernet0/0/0
 ip address 10.97.1.8 255.255.255.0
 ip rip receive version 2
 no ip split-horizon
 no keepalive
!
interface GigabitEthernet1/0/0
 no ip address
 negotiation auto
!
interface GigabitEthernet2/0/0
 no ip address
 negotiation auto
!

Configuración de la interfaz de la muestra N+1

!--- This assumes rfsw2 is on the top, as shown in the cable reference guide.
!--- Other interfaces will be the same, except a different member number for each
!--- HCCP group.

interface Cable5/1/0

!--- This is the Protect for the first group. It may be best to configure the Protect
!--- interface(s) last, after the Working interfaces are configured, or keep the
!--- interface “shut” until finished with all configurations.

 no ip address

!-- No need to set the IP address because it will come from the Working card via SNMP.

 no keepalive

!--- This defaults to 10 seconds with the N+1 Cisco IOS code, but it should be disabled
!--- on the Protect interface or set relatively high.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32

!--- The DS modulation and Interleave must be the same on Protect and Working
!--- of the same group. The Protect interface itself must be “no shut” for HCCP
!--- to activate.

 cable downstream rf-shutdown
 cable upstream 0 shutdown

!--- These will automatically become “no shut” when a failover occurs.

 cable upstream 1 shutdown
 cable upstream 2 shutdown
 cable upstream 3 shutdown
 hccp 1 protect 1 10.10.10.1

!--- This is the HCCP first group and it is protecting member 1 with member one’s
!--- FE IP address. If it is intra-chassis, you can use the Loopback0 IP address.

 hccp 1 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 AA200000 1

!--- This is the IP address of the Switch and it is protecting member 1,
!--- which has a bitmap of AA200000 in Switch slot 1.

 hccp 1 protect 2 10.10.10.1

!--- This is the HCCP first group and it is protecting member 2 with the loopback
!--- IP address.

 hccp 1 channel-switch 2 rfsw2 rfswitch-group 10.97.1.20 AA200000 2

!--- This is the IP address of the Switch and it is protecting member 2,
!--- with a bitmap of AA200000 in Switch slot 2.

 hccp 1 protect 3 10.10.10.1
 hccp 1 channel-switch 3 rfsw2 rfswitch-group 10.97.1.20 AA200000 3
 hccp 1 protect 4 10.10.10.1
 hccp 1 channel-switch 4 rfsw2 rfswitch-group 10.97.1.20 AA200000 4
 hccp 1 protect 5 10.10.10.1
 hccp 1 channel-switch 5 rfsw2 rfswitch-group 10.97.1.20 AA200000 5
 hccp 1 protect 6 10.10.10.1
 hccp 1 channel-switch 6 rfsw2 rfswitch-group 10.97.1.20 AA200000 6
 hccp 1 protect 7 10.10.10.1
 hccp 1 channel-switch 7 rfsw2 rfswitch-group 10.97.1.20 AA200000 7

!--- These channel-switch configurations can be copied and pasted into their
!--- respective Working interfaces.

 hccp 1 timers 5000 15000

!--- hccp 1 timers <hellotime> <holdtime>
!--- This is mostly for inter chassis communication, so set it high for the 10K
!--- as this can create extra CPU load.

 no hccp 1 revertive
!
interface Cable5/1/1

!--- This is the Protect for the second group.

 no ip address
 no keepalive
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream rf-shutdown
 cable upstream 0 shutdown
 cable upstream 1 shutdown
 cable upstream 2 shutdown
 cable upstream 3 shutdown
 !
 hccp 2 protect 1 10.10.10.1
 hccp 2 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 55100000 1

!--- Because this MAC domain is on right side of header, the bitmap in hexadecimal
!--- code is 55100000.

 hccp 2 protect 2 10.10.10.1
 hccp 2 channel-switch 2 rfsw2 rfswitch-group 10.97.1.20 55100000 2
 hccp 2 protect 3 10.10.10.1
 hccp 2 channel-switch 3 rfsw2 rfswitch-group 10.97.1.20 55100000 3
 hccp 2 protect 4 10.10.10.1
 hccp 2 channel-switch 4 rfsw2 rfswitch-group 10.97.1.20 55100000 4
 hccp 2 protect 5 10.10.10.1
 hccp 2 channel-switch 5 rfsw2 rfswitch-group 10.97.1.20 55100000 5
 hccp 2 protect 6 10.10.10.1
 hccp 2 channel-switch 6 rfsw2 rfswitch-group 10.97.1.20 55100000 6
 hccp 2 protect 7 10.10.10.1
 hccp 2 channel-switch 7 rfsw2 rfswitch-group 10.97.1.20 55100000 7
 hccp 2 timers 5000 15000
 no hccp 2 revertive

interface Cable5/1/2

!--- This is the Protect for the third group.

 no ip address
 no keepalive
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream rf-shutdown
 cable upstream 0 shutdown
 cable upstream 1 shutdown
 cable upstream 2 shutdown
 cable upstream 3 shutdown
 hccp 3 protect 1 10.10.10.1
 hccp 3 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 00C80000 1
 hccp 3 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 00C00000 1

!--- Because the third MAC domain will traverse both Switches, two statements are
!--- needed. The “00” in front of the bitmaps will be dropped when viewing the
!--- running configuration.

 no hccp 3 revertive

interface Cable5/1/3

!--- This is the Protect for the fourth group.

 hccp 4 protect 1 10.10.10.1
 hccp 4 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 AA200000 1
 hccp 4 protect 2 10.10.10.1
 hccp 4 channel-switch 2 rfsw1 rfswitch-group 10.97.1. 19 AA200000 2
 hccp 4 protect 3 10.10.10.1
 hccp 4 channel-switch 3 rfsw1 rfswitch-group 10.97.1. 19 AA200000 3
 hccp 4 protect 4 10.10.10.1
 hccp 4 channel-switch 4 rfsw1 rfswitch-group 10.97.1. 19 AA200000 4
 hccp 4 protect 5 10.10.10.1
 hccp 4 channel-switch 5 rfsw1 rfswitch-group 10.97.1. 19 AA200000 5
 hccp 4 protect 6 10.10.10.1
 hccp 4 channel-switch 6 rfsw1 rfswitch-group 10.97.1. 19 AA200000 6
 hccp 4 protect 7 10.10.10.1
 hccp 4 channel-switch 7 rfsw1 rfswitch-group 10.97.1. 19 AA200000 7
 no hccp 4 revertive

interface Cable5/1/4

!--- This is the Protect for the fifth group.

 hccp 5 protect 1 10.10.10.1
 hccp 5 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 55100000 1
 hccp 5 protect 2 10.10.10.1
 hccp 5 channel-switch 2 rfsw1 rfswitch-group 10.97.1. 19 55100000 2
 hccp 5 protect 3 10.10.10.1
 hccp 5 channel-switch 3 rfsw1 rfswitch-group 10.97.1. 19 55100000 3
 hccp 5 protect 4 10.10.10.1
 hccp 5 channel-switch 4 rfsw1 rfswitch-group 10.97.1. 19 55100000 4
 hccp 5 protect 5 10.10.10.1
 hccp 5 channel-switch 5 rfsw1 rfswitch-group 10.97.1. 19 55100000 5
 hccp 5 protect 6 10.10.10.1
 hccp 5 channel-switch 6 rfsw1 rfswitch-group 10.97.1. 19 55100000 6
 hccp 5 protect 7 10.10.10.1
 hccp 5 channel-switch 7 rfsw1 rfswitch-group 10.97.1. 19 55100000 7

!--- Output suppressed.

!
interface Cable8/1/0

!--- This is the Working for the first group.

 ip address 10.192.5.1 255.255.255.0 secondary
 ip address 172.25.1.1 255.255.255.0

!--- Interface bundling is supported as well as subinterfaces.

 ip rip send version 2
 ip rip receive version 2
 keepalive 1

!--- The keepalive time is in seconds and the default is 10 seconds for HCCP code.
!--- Only set this when modems have stabilized.

 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000

!--- This is DS frequency, which must be set for the internal upconverter to operate.

 cable downstream channel-id 0
 no cable downstream rf-shutdown

!--- This is needed to turn on the DS RF output.

 cable upstream 0 frequency 24000000

!--- If you are doing dense mode combining, the upstream frequencies must be different.
!--- If no two US ports are shared, then the same frequency can be used.

 cable upstream 0 power-level 0
 cable upstream 0 connector 0

!--- This is a new command for virtual interfaces, where USs can be used for different
!--- DS MAC domains.

 cable upstream 0 channel-width 3200000
 cable upstream 0 minislot-size 2
 cable upstream 0 modulation-profile 21
 no cable upstream 0 shutdown

!--- Output suppressed.

 cable dhcp-giaddr policy

!--- This tells CMs to get an IP address from the primary scope and
!--- tells CPEs to use the secondary scope.

 hccp 1 working 1

!--- This is Working member 1 of HCCP Group 1.

hccp 1 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 AA200000 1

!--- This is the IP address of Switch and member 1, which has a bitmap of
!--- AA200000 in Switch slot 1.

 hccp 1 reverttime 120

!--- This is the time in minutes (plus 2 minute suspend) for the card to switch back
!--- to normal mode, if the fault has cleared. If a fault was initiated by a keepalive
!--- and you had a fault on the Protect card, it would revert back after the suspend
!--- time and not wait the full revert time.

!
interface Cable8/1/1

!--- This is the Working interface for the second HCCP group.

 ip address 10.192.5.1 255.255.255.0 secondary
 ip address 172.25.2.1 255.255.255.0
 ip rip send version 2
 ip rip receive version 2
 keepalive 1
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000
 cable downstream channel-id 1
 no cable downstream rf-shutdown
 cable upstream 0 frequency 24000000
 cable upstream 0 power-level 0
 cable upstream 0 connector 4
 cable upstream 0 channel-width 3200000
 cable upstream 0 minislot-size 22
 cable upstream 0 modulation-profile 21
 no cable upstream 0 shutdown

!--- Output suppressed.

 cable dhcp-giaddr policy
 hccp 2 working 1

!--- This is Working member 1 of HCCP Group 2.

 hccp 2 channel-switch 1 rfsw2 rfswitch-group 10.97.1.20 55100000 1

!--- This is the IP address of the Switch and Member 1 of Group 2, which has a bitmap
!--- of 55100000 in Switch slot 1.

 hccp 2 reverttime 120
!
interface Cable8/1/2

!--- This is the Working interface for the third HCCP group.

 ip address 10.192.5.1 255.255.255.0 secondary
 ip address 172.25.3.1 255.255.255.0
 ip rip send version 2
 ip rip receive version 2
 keepalive 1
 cable downstream annex B
 cable downstream modulation 64qam
 cable downstream interleave-depth 32
 cable downstream frequency 453000000
 cable downstream channel-id 2
 no cable downstream rf-shutdown
 cable upstream 0 frequency 24000000
 cable upstream 0 power-level 0
 cable upstream 0 connector 8
 cable upstream 0 channel-width 3200000
 cable upstream 0 minislot-size 2
 cable upstream 0 modulation-profile 21
 no cable upstream 0 shutdown
 cable dhcp-giaddr policy

!--- Output suppressed.

 hccp 3 working 1

!--- This is Working member 1 of HCCP Group 3.

 hccp 3 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 00c80000 1
 hccp 3 channel-switch 1 rfsw2 rfswitch-group 10. 97.1.20 00c00000 1
 hccp 3 reverttime 120

interface Cable8/1/3

!---This is the Working interface for the fourth HCCP group.

 hccp 4 working 1
 hccp 4 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 AA200000 1
 hccp 4 reverttime 120

interface Cable8/1/4

!--- This is the Working interface for the fifth HCCP group.

 hccp 5 working 1
 hccp 5 channel-switch 1 rfsw1 rfswitch-group 10.97.1.19 55100000 1
 hccp 5 reverttime 120

!
ip classless
no ip http server
!
no cdp run
snmp-server community private RW

!--- This does not affect the HCCP communications between the Switch and 10K,
!--- unless it is changed.

snmp-server enable traps cable
no cdp run
snmp-server manager
tftp-server server
tftp-server ios.cf alias ios.cf
!
alias exec t configure terminal
alias exec scm show cable modem
alias exec scr sh cab mode remote
alias exec shb sh hccp br
alias exec shd sh hccp detail
alias exec shc sh hccp chan
!
line con 0
 logging synchronous
line aux 0
 no exec
 transport input all

!--- The three lines above were used to console from the Auxiliary port of the 10K
!--- to the Switch.

line vty 0 4
 session-timeout 400
 password xx
 login
endBuilding configuration...

Discusiones relacionadas de la comunidad de soporte de Cisco

La Comunidad de Soporte de Cisco es un foro donde usted puede preguntar y responder, ofrecer sugerencias y colaborar con colegas.


Información Relacionada


Document ID: 49776