Seguridad y VPN : Remote Authentication Dial-In User Service (RADIUS)

Configurar el Basic AAA RADIUS para los clientes dial in

17 Octubre 2016 - Traducción Automática
Otras Versiones: PDFpdf | Inglés (22 Agosto 2015) | Comentarios


Interactivo: Este documento ofrece un análisis personalizado de su dispositivo Cisco.


Contenido


Introducción

Este documento describe una configuración de muestra usando un servidor de acceso para validar el análogo y las conexiones ISDN entrantes, y las autentica usando un servidor del Remote Authentication Dial-In User Service (RADIUS) del Authentication, Authorization, and Accounting (AAA). Para más información sobre el AAA y el RADIUS, refiera a los documentos siguientes:

prerrequisitos

Requisitos

Esta configuración asume que configuran al servidor de RADIUS correctamente. Esta configuración también trabaja con la mayoría de los servidores de RADIUS disponibles en el comercio. Refiera a su documentación del servidor de RADIUS para más información sobre la Configuración del servidor apropiada.

Componentes Utilizados

La información que contiene este documento se basa en las versiones de software y hardware indicadas a continuación.

  • Cisco AS5300 con un T1 PRI y 48 módems digitales. Está funcionando con el Software Release 12.0(7)T del ½ del ¿Â de Cisco IOSïÂ.

  • CiscoSecure para el servidor de Unix (CSU), versión 2.3(3).

La configuración específica AAA descrita aquí se puede también utilizar con cualquier escenario de marcado simple. Asegúrese de que el servidor de acceso pueda validar las llamadas entrantes, después agregan los comandos aaa apropiados, tal y como se muestra en de la configuración abajo.

La información que se presenta en este documento se originó a partir de dispositivos dentro de un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener un comando antes de ejecutarlo.

Convenciones

Para obtener más información sobre las convenciones del documento, consulte Convenciones de Consejos Técnicos de Cisco.

Configurar

En esta sección encontrará la información para configurar las funciones descritas en este documento.

Nota: Para obtener información adicional sobre los comandos que se utilizan en este documento, use la Command Lookup Tool (solo para clientes registrados).

Diagrama de la red

Este documento utiliza la instalación de red que se muestra en el siguiente diagrama.

/image/gif/paws/14966/basic_radius1.gif

Configuraciones

El CSU y la configuración del CiscoSecure NT (CSNT), y configuración del servidor de acceso a la red (NAS) se proporcionan abajo. Puesto que esta configuración representa un simple escenario de marcación, la configuración de CiscoSecure para el ISDN y los usuarios asincrónicos son idénticos. La configuración de cliente ISDN no se incluye pues no es relevante para esta configuración de RADIUS.

CSU
# ./ViewProfile -p 9900 -u async_client
 User Profile Information
 user = async_client{
 profile_id = 110
 profile_cycle = 2
 radius=Cisco {
 check_items= {
 2=cisco

 !--- Password(2) is "cisco"

 }
 reply_attributes= {
 6=2

 !--- Service-Type(6) is Framed (2)

 7=1

 !--- Frame




 d-Protocol(7) is PPP (1)

 }
    }
 }

 # ./ViewProfile -p 9900 -u isdn_user
 User Profile Information
 user = isdn_user{
 profile_id = 24
 profile_cycle = 4
 radius=Cisco {
 check_items= {
 2=cisco

 ! --- Password(2) is "cisco"

 }
 reply_attributes= {
 6=2

 ! --- Service-Type(6) is Framed (2)

 7=1
 
! --- Framed-Protocol(7) is PPP (1)

 }
    }
 }

Nota: Para este simple escenario, las configuraciones del async y los usuarios ISDN son idénticos.

CSNT RADIUS

Para configurar el CiscoSecure NT (CSNT) RADIUS:

  1. Cree a los usuarios nuevos nombrados isdn_user y async_client.

  2. Configure la contraseña apropiada en la sección de configuración de usuario

  3. En la sección para los atributos de RADIUS de la Fuerza de tareas de ingeniería en Internet (IETF) (IETF), seleccione los elementos siguientes del menú desplegable:

    Tipo de servicio (atributo 6) = Framed y Protocolo Entramado (atributo 7)=PPP

    Nota: Usted debe hacer clic el checkbox situado al lado de los atributos tipo de servicio y Protocolo Entramado.

    Nota: Para este simple escenario, las configuraciones del async y los usuarios ISDN son idénticos.

maui-nas-01
maui-nas-01#show running-config 
 Building configuration...

 Current configuration:
 !
 version 12.0
 service timestamps debug datetime msec
 service timestamps log datetime msec
 service password-encryption
 !
 hostname maui-nas-01
 !
 aaa new-model

 !--- Initiates the AAA access control system. 
 !--- This command immediately locks down login and PPP authentication.

 aaa authentication login default group radius local

 !--- Exec login (for the list default) is authenticated using methods 
 !--- radius then local. The router uses RADIUS for authentication at the  
 !--- login(exec) prompt. If RADIUS returns an error, the user is authenticated 
 !--- using the local database.

 aaa authentication login NO_AUTHEN none

 !--- Exec login (for the list NO_AUTHEN) has authentication method none 
 !--- (no authentication). Interfaces to which this list is applied will not have 
 !--- authentication enabled. Refer to the console port (line con 0) configuration.

 aaa authentication ppp default if-needed group radius local

 !--- PPP authentication (for the list default) uses methods radius then local.
 !--- The if-needed keyword automatically permits ppp for users that have 
 !--- successfully authenticated using exec mode. If the EXEC facility has 
 !--- authenticated the user, RADIUS authentication for PPP is not performed.
 !----This is necessary for clients that use terminal window after dial.

 aaa authorization network default group radius local

 !--- Authorization of network services (PPP services) for the list default
 !--- uses methods radius then local. This is neccessary if you use RADIUS 
 !--- for the client IP address, Access List assignment and so on.

 enable secret 5 <deleted>
 !
 username admin password 7 <deleted>

 !--- This username allows for access to the router in situations where 
 !--- connectivity to the RADIUS server is lost. This is because the AAA 
 !--- configuration for exec login has the alternate method local. 

 spe 2/0 2/7
  firmware location system:/ucode/mica_port_firmware
 !
 resource-pool disable
 !
 ip subnet-zero
 no ip finger
 !
 isdn switch-type primary-ni

 !--- Switch type is Primary NI-2.

 isdn voice-call-failure 0
 mta receive maximum-recipients 0
 !
 !
 controller T1 0

 !--- T1 0 controller configuration.

  framing esf
  clock source line primary
  linecode b8zs
  pri-group timeslots 1-24
 !
 controller T1 1

 !--- T1 1 is unused.

  clock source line secondary 1
 !
 controller T1 2

 !--- T1 1 is unused.

 !
 controller T1 3

 !--- T1 1 is unused.

 !
 interface Ethernet0
  ip address 172.22.53.141 255.255.255.0
  no ip directed-broadcast
 !
 interface Serial0:23

 !--- D-channel configuration for T1 0.

  no ip address
  no ip directed-broadcast
  encapsulation ppp
  dialer pool-member 23

 !--- Assign Serial0:23 as member of dialer pool 23.
 !--- Dialer pool 23 is specified in interface Dialer 1.
 !--- Interface Dialer 1 will terminate the ISDN calls.

  isdn switch-type primary-ni
  isdn incoming-voice modem

 !--- Switch incoming analog calls to the internal digital modems.

  no cdp enable
 !
 interface FastEthernet0
  no ip address
  no ip directed-broadcast
  shutdown
  duplex auto
  speed auto
 !
 interface Group-Async0

 !--- Async Group Interface for the modems.

  ip unnumbered Ethernet0

 !--- Unnumbered to the ethernet interface.

  no ip directed-broadcast
  encapsulation ppp
  async mode interactive

 !--- Configures interactive mode on the asynchronous interfaces.
 !--- This allows users to dial in and get to a shell or PPP session on 
 !--- that line. If you want incoming users to only connect using PPP configure 
 !--- async mode dedicated instead.

  peer default ip address pool ASYNC

 !--- Use the ip pool named "ASYNC" to assign ip address for 
 !--- incoming connections.

  ppp authentication chap
  group-range 1 48

 !--- Lines(modems) 1 through 48 are in this group async interface.

 !
 interface Dialer1

 !--- Dialer1 will terminate ISDN calls.

  ip unnumbered Ethernet0
  no ip directed-broadcast
  encapsulation ppp
  dialer pool 23

 !--- Dialer 1 uses dialer pool 23. Interface Serial0:23 is 
 !--- a member of this pool.

  peer default ip address pool ISDN

 !--- Use the ip pool named "ISDN" to assign ip address for 
 !--- incoming connections.

  no cdp enable
  ppp authentication chap
 !
 ip local pool ISDN 172.22.53.142 172.22.53.145

 !--- IP address pool named "ISDN". 
 !--- This pool will be assigned to connections on interface Dialer 1.

 ip local pool ASYNC 172.22.53.146 172.22.53.149

 !--- IP address pool named "ASYNC". 
 !--- This pool will be assigned to incoming connections on Group-Async 0.
 !--- Note: This address pool only has 4 addresses and is not sufficient to 
 !--- support all 48 modem lines. Configure your IP pool with the address range 
 !--- to support all connections.

 ip classless
 no ip http server
 !
 no cdp run
 !
 radius-server host 172.22.53.201 auth-port 1645 acct-port 1646 key cisco

 !--- Radius-server host IP address and encryption key. 
 !--- The encryption key must match the onbe configured on the RADIUS server.

 !
 line con 0
  exec-timeout 0 0
  login authentication NO_AUTHEN

 !--- Specifies that the AAA list name assigned to the console is 
 !--- NO_AUTHEN. From the AAA configuration above, the list NO_AUTHEN 
 !--- does not use authentication.

  transport input none
 line 1 48

  autoselect during-login

 !--- Displays the username:password prompt after modems connect. 
 !--- Without this the user must press enter to receive a prompt.

  autoselect ppp

 !--- When the NAS detects incoming PPP packets, the PPP session
 !--- will be launched.

  modem InOut
  transport preferred none
  transport input all
  transport output none
 line aux 0
 line vty 0 4
 !
 end

Verificación

Esta sección proporciona la información que usted puede utilizar para verificar su configuración.

Salida de presentación de ejemplo

maui-nas-01#show caller user async_client detail

  User: async_client, line tty 5, service Async
        Active time 00:01:04, Idle time 00:00:22
  Timeouts:            Absolute  Idle      Idle
                                 Session   Exec
      Limits:          -         -         00:10:00  
      Disconnect in:   -         -         -         
  TTY: Line 5, running PPP on As5
  Location: PPP: 172.22.53.148

  !--- The IP address assigned from the the IP pool. 

  DS0: (slot/unit/channel)=0/0/7
  Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
  Status: Ready, Active, No Exit Banner, Async Interface Active
          HW PPP Support Active
  Capabilities: Hardware Flowcontrol In, Hardware Flowcontrol Out
                Modem Callout, Modem RI is CD, 
                Line usable as async interface, Integrated Modem
  Modem State: Ready

  User: async_client, line As5, service PPP
        Active time 00:00:54, Idle time 00:00:23
  Timeouts:            Absolute  Idle
      Limits:          -         -         
      Disconnect in:   -         -         
  PPP: LCP Open, CHAP (<- AAA), IPCP

  !--- CHAP authentication was performed by AAA.

  LCP: -> peer, ACCM, AuthProto, MagicNumber, PCompression, ACCompression
       <- peer, ACCM, MagicNumber, PCompression, ACCompression
  NCP: Open IPCP
  IPCP: <- peer, Address
        -> peer, Address
  IP: Local 172.22.53.141, remote 172.22.53.148
  Counts: 40 packets input, 2769 bytes, 0 no buffer
          1 input errors, 1 CRC, 0 frame, 0 overrun
          24 packets output, 941 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets


maui-nas-01#show caller user isdn_user detail

  User: isdn_user, line Se0:8, service PPP
        Active time 00:01:22, Idle time 00:01:24
  Timeouts:            Absolute  Idle
      Limits:          -         00:02:00  
      Disconnect in:   -         00:00:35  
  PPP: LCP Open, CHAP (<- AAA), IPCP

!--- CHAP authentication was performed by AAA.

  LCP: -> peer, AuthProto, MagicNumber
       <- peer, MagicNumber
  NCP: Open IPCP
  IPCP: <- peer, Address
        -> peer, Address
  Dialer: Connected to , inbound
          Idle timer 120 secs, idle 84 secs
          Type is ISDN, group Dialer1

  ! -- The ISDN Call uses int Dialer1.

  IP: Local 172.22.53.141, remote 172.22.53.142

  ! -- The IP address was obtained from the local pool.

  Counts: 31 packets input, 872 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          34 packets output, 1018 bytes, 0 underruns
          0 output errors, 0 collisions, 5 interface resets

Troubleshooting

En esta sección encontrará información que puede utilizar para solucionar problemas de configuración.

Comandos para resolución de problemas

La herramienta Output Interpreter (sólo para clientes registrados) permite utilizar algunos comandos “show” y ver un análisis del resultado de estos comandos.

Nota: Antes de ejecutar un comando debug, consulte Información Importante sobre Comandos Debug.

  • debug isdn q931 - Muestra la configuración de la llamada y cierra la conexión de red ISDN (Capa 3) entre el router y el switch ISDN.

  • módem del debug - Esto muestra la actividad de línea del módem en un servidor de acceso.

  • negociación ppp del debug - Al mostrar información en el tráfico y los intercambios PPP mientras que negocia el (LCP), la autenticación, y el protocolo network control del Link Control Protocol (NCP). Una negociación PPP exitosa abre primero el estado LCP, luego realiza la autenticación y por último negocia el NCP.

  • debug ppp authentication – Permite mostrar los mensajes del protocolo de autenticación PPP, entre ellos el intercambio de paquetes del Protocolo de confirmación de aceptación de la autenticación (CHAP) y los intercambios de protocolo de autenticación de contraseña (PAP).

  • autenticación aaa del debug - Al mostrar información en la autenticación AAA/RADIUS.

  • debug aaa authorization - Al mostrar información en la autorización AAA/RADIUS.

  • radio del debug - Para visualizar la información de debugging detallada asociada al RADIUS. Utilice la herramienta Output Interpreter (clientes registrados solamente) en el sitio web del Soporte técnico de Cisco para decodificar los mensajes de RADIUS del debug. Por un ejemplo, refiera a la salida de los debugs mostrada abajo. Utilice la información del radio del debug para determinar se negocian qué atributos. Nota: A partir de 12.2(11)T que la salida del radio del debug está decodificada ya y por lo tanto que no requiere el uso del Output Interpreter de decodificar la salida. Refiera a las mejoras del debug del documento RADIUS para más información

  • caller user de la demostración - Para mostrar los parámetros para el usuario determinado tal como la línea TTY usada, interfaz asincrónica (estante, slot o puerto), número de canal del DS0, número del módem, dirección IP asignada, parámetros de agrupamiento PPP y PPP, y así sucesivamente. Si su versión del software del IOS de Cisco no es compatible con este comando, utilice el comando show user.

Ejemplo de resultado del comando debug

basicradius_2.gif

Si usted tiene la salida de un comando debug radius de su dispositivo de Cisco, usted puede utilizar para visualizar los problemas potenciales y los arreglos. Para utilizar , usted debe ser un cliente registrado, se abra una sesión, y hace el Javascript habilitar.

Nota: A partir de 12.2(11)T que la salida del radio del debug está decodificada ya y por lo tanto que no requiere el uso del Output Interpreter de decodificar la salida. Refiera a las mejoras del debug del documento RADIUS para más información

maui-nas-01#debug isdn q931
ISDN Q931 packets debugging is on
maui-nas-01#debug ppp negotiation 
PPP protocol negotiation debugging is on
maui-nas-01#debug ppp authentication
PPP authentication debugging is on
maui-nas-01#debug modem
Modem control/process activation debugging is on
maui-nas-01#debug aaa authentication 
AAA Authentication debugging is on
maui-nas-01#debug aaa authorization 
AAA Authorization debugging is on
maui-nas-01#debug radius
RADIUS protocol debugging is on

maui-nas-01#
*Apr  5 11:05:07.031: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x20FC

!--- Setup message for incoming call.

*Apr  5 11:05:07.031:         Bearer Capability i = 0x8890218F
*Apr  5 11:05:07.031:         Channel ID i = 0xA18387
*Apr  5 11:05:07.031:         Called Party Number i = 0xA1, '81560'
*Apr  5 11:05:07.035: %DIALER-6-BIND: Interface Serial0:6 bound to profile Dialer1
*Apr  5 11:05:07.035: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0xA0FC
*Apr  5 11:05:07.035:         Channel ID i = 0xA98387
*Apr  5 11:05:07.043: %LINK-3-UPDOWN: Interface Serial0:6, changed state to up
*Apr  5 11:05:07.043: Se0:6 PPP: Treating connection as a callin
*Apr  5 11:05:07.043: Se0:6 PPP: Phase is ESTABLISHING, Passive Open
*Apr  5 11:05:07.043: Se0:6 LCP: State is Listen
*Apr  5 11:05:07.047: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0xA0FC
*Apr  5 11:05:07.047:         Channel ID i = 0xA98387
*Apr  5 11:05:07.079: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x20FC

*Apr  5 11:05:07.079: ISDN Se0:23: CALL_PROGRESS: CALL_CONNECTED call id 0x2D, 
bchan -1, dsl 0
*Apr  5 11:05:07.499: Se0:6 LCP: I CONFREQ [Listen] id 28 len 10
*Apr  5 11:05:07.499: Se0:6 LCP:    MagicNumber 0x5078A51F (0x05065078A51F)
*Apr  5 11:05:07.499: Se0:6 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Apr  5 11:05:07.499: Se0:6 LCP: O CONFREQ [Listen] id 2 len 15
*Apr  5 11:05:07.499: Se0:6 LCP:    AuthProto CHAP (0x0305C22305)
*Apr  5 11:05:07.499: Se0:6 LCP:    MagicNumber 0xE05213AA (0x0506E05213AA)
*Apr  5 11:05:07.499: Se0:6 LCP: O CONFACK [Listen] id 28 len 10
*Apr  5 11:05:07.499: Se0:6 LCP:    MagicNumber 0x5078A51F (0x05065078A51F)
*Apr  5 11:05:07.555: Se0:6 LCP: I CONFACK [ACKsent] id 2 len 15
*Apr  5 11:05:07.555: Se0:6 LCP:    AuthProto CHAP (0x0305C22305)
*Apr  5 11:05:07.555: Se0:6 LCP:    MagicNumber 0xE05213AA (0x0506E05213AA)
*Apr  5 11:05:07.555: Se0:6 LCP: State is Open
*Apr  5 11:05:07.555: Se0:6 PPP: Phase is AUTHENTICATING, by this end
*Apr  5 11:05:07.555: Se0:6 CHAP: O CHALLENGE id 2 len 32 from "maui-nas-01"
*Apr  5 11:05:07.631: Se0:6 CHAP: I RESPONSE id 2 len 30 from "isdn_user"

!--- Incoming CHAP response from "isdn_user".

*Apr  5 11:05:07.631: AAA: parse name=Serial0:6 idb type=12 tty=-1
*Apr  5 11:05:07.631: AAA: name=Serial0:6 flags=0x51 type=1 shelf=0 slot=0 
adapter=0 port=0 channel=6
*Apr  5 11:05:07.631: AAA: parse name= idb type=-1 tty=-1
*Apr  5 11:05:07.631: AAA/MEMORY: create_user (0x619CEE28) user='isdn_user' 
ruser='' port='Serial0:6' rem_addr='isdn/81560' authen_type=CHAP service=PPP 
priv=1
*Apr  5 11:05:07.631: AAA/AUTHEN/START (2973699846): port='Serial0:6' list='' 
action=LOGIN service=PPP
*Apr  5 11:05:07.631: AAA/AUTHEN/START (2973699846): using "default" list
*Apr  5 11:05:07.631: AAA/AUTHEN (2973699846): status = UNKNOWN
*Apr  5 11:05:07.631: AAA/AUTHEN/START (2973699846): Method=radius (radius)

!--- AAA authentication method is RADIUS.

*Apr  5 11:05:07.631: RADIUS: ustruct sharecount=1
*Apr  5 11:05:07.631: RADIUS: Initial Transmit Serial0:6 id 13 172.22.53.201:1645, 
Access-Request, len 87

!--- Access-Request from the NAS to the AAA server.
!--- Note the IP address in the Access-Request matches the IP address 
!--- configured using the command:
!--- radius-server host 172.22.53.201 key cisco 

*Apr  5 11:05:07.631:         Attribute 4 6 AC16358D
*Apr  5 11:05:07.631:         Attribute 5 6 00004E26
*Apr  5 11:05:07.631:         Attribute 61 6 00000002
*Apr  5 11:05:07.631:         Attribute 1 11 6973646E
*Apr  5 11:05:07.631:         Attribute 30 7 38313536
*Apr  5 11:05:07.631:         Attribute 3 19 0297959E
*Apr  5 11:05:07.631:         Attribute 6 6 00000002
*Apr  5 11:05:07.631:         Attribute 7 6 00000001
*Apr  5 11:05:07.635: RADIUS: Received from id 13 172.22.53.201:1645, 
Access-Accept, len 32
*Apr  5 11:05:07.635:         Attribute 6 6 00000002
*Apr  5 11:05:07.635:         Attribute 7 6 00000001

Los pares de valores de atributos (AVP) de la necesidad del comando debug radius de ser decodificado para entender mejor la transacción entre el NAS y el servidor de RADIUS.

Nota: A partir de 12.2(11)T que la salida del radio del debug está decodificada ya y por lo tanto que no requiere el uso del Output Interpreter de decodificar la salida. Refiera a las mejoras del debug del documento RADIUS para más información.

La herramienta del Output Interpreter permite que usted reciba un análisis de la salida del radio del debug.

El producto siguiente en los itálicos es el resultado obtenido de la herramienta del Output Interpreter:

Access-Request 172.22.53.201:1645 id 13
Attribute Type 4:  NAS-IP-Address is 172.22.53.141
Attribute Type 5:  NAS-Port is 20006
Attribute Type 61: NAS-Port-Type is ISDN-Synchronous
Attribute Type 1:  User-Name is isdn
Attribute Type 30: Called-Station-ID(DNIS) is 8156
Attribute Type 3:  CHAP-Password is (encoded)
Attribute Type 6:  Service-Type is Framed
Attribute Type 7:  Framed-Protocol is PPP
Access-Accept 172.22.53.201:1645 id 13
Attribute Type 6:  Service-Type is Framed
Attribute Type 7:  Framed-Protocol is PPP

De la salida de los debugs decodificada por la herramienta, verifique ese tipo 6 del atributo: El tipo de servicio capítulo y el tipo 7 del atributo: El Protocolo Entramado es PPP. Si usted observa que los atributos 6 o 7 no están como se muestra, corrija el perfil del usuario en el servidor de RADIUS (refiera a la sección de configuración). También note que el radio del debug muestra un access-accept, que indica que el servidor de RADIUS autenticó con éxito al usuario. Si la salida muestra un Access-Reject, después no autenticaron al usuario y usted debe marcar la configuración del nombre de usuario y contraseña en el servidor de RADIUS. Otro atributo a verificar es el tipo 4 del atributo: Nas-ip-address. Verifique que el valor visualizado por la herramienta del Output Interpreter haga juego la dirección IP NAS configurada en el servidor de RADIUS.

Nota: Debido a las restricciones de Cisco IOS y a las diferencias en la salida de los debugs con diversas versiones, algunos atributos pueden ser truncados (por ejemplo, username, Llamar-estación-ID(DNIS)).

*Apr  5 11:05:07.635: AAA/AUTHEN (2973699846): status = PASS

!--- Authentication is successful

*Apr  5 11:05:07.635: Se0:6 AAA/AUTHOR/LCP: Authorize LCP
*Apr  5 11:05:07.635: Se0:6 AAA/AUTHOR/LCP (2783657211): Port='Serial0:6' 
list='' service=NET
*Apr  5 11:05:07.635: AAA/AUTHOR/LCP: Se0:6 (2783657211) user='isdn_user'
*Apr  5 11:05:07.635: Se0:6 AAA/AUTHOR/LCP (2783657211): send AV service=ppp
*Apr  5 11:05:07.635: Se0:6 AAA/AUTHOR/LCP (2783657211): send AV protocol=lcp
*Apr  5 11:05:07.635: Se0:6 AAA/AUTHOR/LCP (2783657211): found list "default"
*Apr  5 11:05:07.635: Se0:6 AAA/AUTHOR/LCP (2783657211): Method=radius (radius)
*Apr  5 11:05:07.635: Se0:6 AAA/AUTHOR (2783657211): Post authorization status 
= PASS_REPL
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR/LCP: Processing AV service=ppp
*Apr  5 11:05:07.639: Se0:6 CHAP: O SUCCESS id 2 len 4
*Apr  5 11:05:07.639: Se0:6 PPP: Phase is UP
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR/FSM (3184893369): Port='Serial0:6' list='' 
service=NET
*Apr  5 11:05:07.639: AAA/AUTHOR/FSM: Se0:6 (3184893369) user='isdn_user'
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR/FSM (3184893369): send AV service=ppp
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR/FSM (3184893369): send AV protocol=ip
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR/FSM (3184893369): found list "default"
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR/FSM (3184893369): Method=radius (radius)
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR (3184893369): Post authorization status 
= PASS_REPL
*Apr  5 11:05:07.639: Se0:6 AAA/AUTHOR/FSM: We can start IPCP
*Apr  5 11:05:07.639: Se0:6 IPCP: O CONFREQ [Not negotiated] id 2 len 10
*Apr  5 11:05:07.639: Se0:6 IPCP:    Address 172.22.53.141 (0x0306AC16358D)
*Apr  5 11:05:07.675: Se0:6 IPCP: I CONFREQ [REQsent] id 13 len 10
*Apr  5 11:05:07.675: Se0:6 IPCP:    Address 0.0.0.0 (0x030600000000)
*Apr  5 11:05:07.675: Se0:6 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, 
we want 0.0.0.0
*Apr  5 11:05:07.675: Se0:6 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Apr  5 11:05:07.675: Se0:6 AAA/AUTHOR/IPCP: Authorization succeeded
*Apr  5 11:05:07.675: Se0:6 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, 
we want 0.0.0.0
*Apr  5 11:05:07.675: Se0:6 IPCP: Pool returned 172.22.53.142

!--- IP address for the peer obtained from the pool

*Apr  5 11:05:07.675: Se0:6 IPCP: O CONFNAK [REQsent] id 13 len 10
*Apr  5 11:05:07.675: Se0:6 IPCP:    Address 172.22.53.142 (0x0306AC16358E)
*Apr  5 11:05:07.699: Se0:6 IPCP: I CONFACK [REQsent] id 2 len 10
*Apr  5 11:05:07.699: Se0:6 IPCP:    Address 172.22.53.141 (0x0306AC16358D)
*Apr  5 11:05:07.707: Se0:6 IPCP: I CONFREQ [ACKrcvd] id 14 len 10
*Apr  5 11:05:07.707: Se0:6 IPCP:    Address 172.22.53.142 (0x0306AC16358E)
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP: Start.  Her address 172.22.53.142, 
we want 172.22.53.142
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP (3828612481): Port='Serial0:6' 
list='' service=NET
*Apr  5 11:05:07.707: AAA/AUTHOR/IPCP: Se0:6 (3828612481) user='isdn_user'
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP (3828612481): send AV service=ppp
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP (3828612481): send AV protocol=ip
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP (3828612481): send AV 
addr*172.22.53.142
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP (3828612481): found list "default"
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP (3828612481): Method=radius (radius)
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR (3828612481): Post authorization status 
= PASS_REPL
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP: Reject 172.22.53.142, 
using 172.22.53.142
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP: Processing AV addr*172.22.53.142
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP: Authorization succeeded
*Apr  5 11:05:07.707: Se0:6 AAA/AUTHOR/IPCP: Done.  Her address 172.22.53.142, 
we want 172.22.53.142
*Apr  5 11:05:07.707: Se0:6 IPCP: O CONFACK [ACKrcvd] id 14 len 10
*Apr  5 11:05:07.707: Se0:6 IPCP:    Address 172.22.53.142 (0x0306AC16358E)
*Apr  5 11:05:07.707: Se0:6 IPCP: State is Open
*Apr  5 11:05:07.711: Di1 IPCP: Install route to 172.22.53.142

!--- IPCP state is open. A route to the remote peer is installed

*Apr  5 11:05:08.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:6, 
changed state to up
*Apr  5 11:05:13.043: %ISDN-6-CONNECT: Interface Serial0:6 is now connected 
to isdn_user
maui-nas-01#

Esto completa la negociación para el cliente ISDN. La salida mostrada abajo muestra a negociación para una llamada asincrónica (por ejemplo, un cliente de Windows)

maui-nas-01#
*Apr  5 11:05:53.527: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x21C5

!--- Incoming Setup message for Async Call.

*Apr  5 11:05:53.527:         Bearer Capability i = 0x9090A2
*Apr  5 11:05:53.527:         Channel ID i = 0xA18388
*Apr  5 11:05:53.527:         Progress Ind i = 0x8183 - Origination address 
is non-ISDN 
*Apr  5 11:05:53.527:         Called Party Number i = 0xA1, '81560'
*Apr  5 11:05:53.531: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0xA1C5
*Apr  5 11:05:53.531:         Channel ID i = 0xA98388
*Apr  5 11:05:53.531: ISDN Se0:23: TX ->  ALERTING pd = 8  callref = 0xA1C5
*Apr  5 11:05:53.667: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0xA1C5
*Apr  5 11:05:53.683: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x21C5

*Apr  5 11:05:53.687: ISDN Se0:23: CALL_PROGRESS: CALL_CONNECTED call id 0x2E, 
bchan -1, dsl 0
*Apr  5 11:06:10.815: TTY5: DSR came up
*Apr  5 11:06:10.815: tty5: Modem: IDLE->(unknown)
*Apr  5 11:06:10.815: TTY5: EXEC creation
*Apr  5 11:06:10.815: AAA: parse name=tty5 idb type=10 tty=5
*Apr  5 11:06:10.815: AAA: name=tty5 flags=0x11 type=4 shelf=0 slot=0 adapter=0 
port=5 channel=0
*Apr  5 11:06:10.815: AAA: parse name=Serial0:7 idb type=12 tty=-1
*Apr  5 11:06:10.815: AAA: name=Serial0:7 flags=0x51 type=1 shelf=0 slot=0 
adapter=0 port=0 channel=7
*Apr  5 11:06:10.815: AAA/MEMORY: create_user (0x614D4DBC) user='' ruser='' 
port='tty5' rem_addr='async/81560' authen_type=ASCII service=LOGIN priv=1
*Apr  5 11:06:10.815: AAA/AUTHEN/START (2673527044): port='tty5' list='' 
action=LOGIN service=LOGIN
*Apr  5 11:06:10.815: AAA/AUTHEN/START (2673527044): using "default" list
*Apr  5 11:06:10.815: AAA/AUTHEN/START (2673527044): Method=radius (radius)
*Apr  5 11:06:10.815: AAA/AUTHEN (2673527044): status = GETUSER
*Apr  5 11:06:10.815: TTY5: set timer type 10, 30 seconds
*Apr  5 11:06:13.475: TTY5: Autoselect(2) sample 7E
*Apr  5 11:06:13.475: TTY5: Autoselect(2) sample 7EFF
*Apr  5 11:06:13.475: TTY5: Autoselect(2) sample 7EFF7D
*Apr  5 11:06:13.475: TTY5: Autoselect(2) sample 7EFF7D23
*Apr  5 11:06:13.475: TTY5 Autoselect cmd:  ppp negotiate

!--- the router recongnizes the ppp packets and launches ppp.

*Apr  5 11:06:13.475: AAA/AUTHEN/ABORT: (2673527044) because Autoselected.
*Apr  5 11:06:13.475: AAA/MEMORY: free_user (0x614D4DBC) user='' ruser='' 
port='tty5' rem_addr='async/81560' authen_type=ASCII service=LOGIN priv=1
*Apr  5 11:06:13.479: TTY5: EXEC creation
*Apr  5 11:06:13.479: TTY5: create timer type 1, 600 seconds
*Apr  5 11:06:13.607: TTY5: destroy timer type 1 (OK)
*Apr  5 11:06:13.607: TTY5: destroy timer type 0
*Apr  5 11:06:15.607: %LINK-3-UPDOWN: Interface Async5, changed state to up
*Apr  5 11:06:15.607: As5 PPP: Treating connection as a dedicated line
*Apr  5 11:06:15.607: As5 PPP: Phase is ESTABLISHING, Active Open

!--- PPP negotiation begins.

*Apr  5 11:06:15.607: As5 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Apr  5 11:06:15.607: As5 LCP: O CONFREQ [Closed] id 1 len 25
*Apr  5 11:06:15.607: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:15.607: As5 LCP:    AuthProto CHAP (0x0305C22305)
*Apr  5 11:06:15.607: As5 LCP:    MagicNumber 0xE0531DB8 (0x0506E0531DB8)
*Apr  5 11:06:15.607: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:15.607: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:16.487: As5 LCP: I CONFREQ [REQsent] id 3 len 23
*Apr  5 11:06:16.487: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:16.487: As5 LCP:    MagicNumber 0x65FFA5C7 (0x050665FFA5C7)
*Apr  5 11:06:16.487: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:16.487: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:16.487: As5 LCP:    Callback 6  (0x0D0306)
*Apr  5 11:06:16.487: Unthrottle 5
*Apr  5 11:06:16.487: As5 LCP: O CONFREJ [REQsent] id 3 len 7
*Apr  5 11:06:16.487: As5 LCP:    Callback 6  (0x0D0306)
*Apr  5 11:06:17.607: As5 LCP: TIMEout: State REQsent
*Apr  5 11:06:17.607: As5 LCP: O CONFREQ [REQsent] id 2 len 25
*Apr  5 11:06:17.607: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:17.607: As5 LCP:    AuthProto CHAP (0x0305C22305)
*Apr  5 11:06:17.607: As5 LCP:    MagicNumber 0xE0531DB8 (0x0506E0531DB8)
*Apr  5 11:06:17.607: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:17.607: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:17.735: As5 LCP: I CONFACK [REQsent] id 2 len 25
*Apr  5 11:06:17.735: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:17.735: As5 LCP:    AuthProto CHAP (0x0305C22305)
*Apr  5 11:06:17.735: As5 LCP:    MagicNumber 0xE0531DB8 (0x0506E0531DB8)
*Apr  5 11:06:17.735: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:17.735: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:19.479: As5 LCP: I CONFREQ [ACKrcvd] id 4 len 23
*Apr  5 11:06:19.479: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:19.479: As5 LCP:    MagicNumber 0x65FFA5C7 (0x050665FFA5C7)
*Apr  5 11:06:19.479: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:19.479: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:19.479: As5 LCP:    Callback 6  (0x0D0306)
*Apr  5 11:06:19.479: As5 LCP: O CONFREJ [ACKrcvd] id 4 len 7
*Apr  5 11:06:19.479: As5 LCP:    Callback 6  (0x0D0306)
*Apr  5 11:06:19.607: As5 LCP: TIMEout: State ACKrcvd
*Apr  5 11:06:19.607: As5 LCP: O CONFREQ [ACKrcvd] id 3 len 25
*Apr  5 11:06:19.607: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:19.607: As5 LCP:    AuthProto CHAP (0x0305C22305)
*Apr  5 11:06:19.607: As5 LCP:    MagicNumber 0xE0531DB8 (0x0506E0531DB8)
*Apr  5 11:06:19.607: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:19.607: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:19.607: As5 LCP: I CONFREQ [REQsent] id 5 len 20
*Apr  5 11:06:19.607: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:19.607: As5 LCP:    MagicNumber 0x65FFA5C7 (0x050665FFA5C7)
*Apr  5 11:06:19.607: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:19.607: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:19.607: As5 LCP: O CONFACK [REQsent] id 5 len 20
*Apr  5 11:06:19.607: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:19.607: As5 LCP:    MagicNumber 0x65FFA5C7 (0x050665FFA5C7)
*Apr  5 11:06:19.607: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:19.607: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:19.719: As5 LCP: I CONFACK [ACKsent] id 3 len 25
*Apr  5 11:06:19.719: As5 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Apr  5 11:06:19.719: As5 LCP:    AuthProto CHAP (0x0305C22305)
*Apr  5 11:06:19.719: As5 LCP:    MagicNumber 0xE0531DB8 (0x0506E0531DB8)
*Apr  5 11:06:19.719: As5 LCP:    PFC (0x0702)
*Apr  5 11:06:19.719: As5 LCP:    ACFC (0x0802)
*Apr  5 11:06:19.719: As5 LCP: State is Open
*Apr  5 11:06:19.719: As5 PPP: Phase is AUTHENTICATING, by this end
*Apr  5 11:06:19.719: As5 CHAP: O CHALLENGE id 1 len 32 from "maui-nas-01"
*Apr  5 11:06:19.863: As5 CHAP: I RESPONSE id 1 len 33 from "async_client"

!--- Incoming CHAP response from "async_client".

*Apr  5 11:06:19.863: AAA: parse name=Async5 idb type=10 tty=5
*Apr  5 11:06:19.863: AAA: name=Async5 flags=0x11 type=4 shelf=0 slot=0 
adapter=0 port=5 channel=0
*Apr  5 11:06:19.863: AAA: parse name=Serial0:7 idb type=12 tty=-1
*Apr  5 11:06:19.863: AAA: name=Serial0:7 flags=0x51 type=1 shelf=0 slot=0 
adapter=0 port=0 channel=7
*Apr  5 11:06:19.863: AAA/MEMORY: create_user (0x6195AE40) user='async_client' 
ruser='' port='Async5' rem_addr='async/81560' authen_type=CHAP service=PPP 
priv=1
*Apr  5 11:06:19.863: AAA/AUTHEN/START (2673347869): port='Async5' list='' 
action=LOGIN service=PPP
*Apr  5 11:06:19.863: AAA/AUTHEN/START (2673347869): using "default" list
*Apr  5 11:06:19.863: AAA/AUTHEN (2673347869): status = UNKNOWN
*Apr  5 11:06:19.863: AAA/AUTHEN/START (2673347869): Method=radius (radius)
*Apr  5 11:06:19.863: RADIUS: ustruct sharecount=1
*Apr  5 11:06:19.867: RADIUS: Initial Transmit Async5 id 14 172.22.53.201:1645, 
Access-Request, len 90
*Apr  5 11:06:19.867:         Attribute 4 6 AC16358D
*Apr  5 11:06:19.867:         Attribute 5 6 00000005
*Apr  5 11:06:19.867:         Attribute 61 6 00000000
*Apr  5 11:06:19.867:         Attribute 1 14 6173796E
*Apr  5 11:06:19.867:         Attribute 30 7 38313536
*Apr  5 11:06:19.867:         Attribute 3 19 01B8292F
*Apr  5 11:06:19.867:         Attribute 6 6 00000002
*Apr  5 11:06:19.867:         Attribute 7 6 00000001
*Apr  5 11:06:19.867: RADIUS: Received from id 14 172.22.53.201:1645, 
Access-Accept, len 32
*Apr  5 11:06:19.867:         Attribute 6 6 00000002
*Apr  5 11:06:19.871:         Attribute 7 6 00000001

Los AVP del comando debug radius necesitan ser decodificados para entender mejor la transacción entre el NAS y el servidor de RADIUS.

Nota: A partir de 12.2(11)T que la salida del radio del debug está decodificada ya y por lo tanto que no requiere el uso del Output Interpreter de decodificar la salida. Refiera a las mejoras del debug del documento RADIUS para más información

La herramienta del Output Interpreter permite que usted reciba un análisis de la salida del radio del debug.

El producto siguiente en los itálicos es el resultado obtenido de la herramienta del Output Interpreter:

Access-Request 172.22.53.201:1645 id 14
Attribute Type 4:  NAS-IP-Address is 172.22.53.141
Attribute Type 5:  NAS-Port is 5
Attribute Type 61: NAS-Port-Type is Asynchronous
Attribute Type 1:  User-Name is asyn
Attribute Type 30: Called-Station-ID(DNIS) is 8156
Attribute Type 3:  CHAP-Password is (encoded)
Attribute Type 6:  Service-Type is Framed
Attribute Type 7:  Framed-Protocol is PPP
         Access-Accept 172.22.53.201:1645 id 14
Attribute Type 6:  Service-Type is Framed
Attribute Type 7:  Framed-Protocol is PPP

De la salida de los debugs decodificada por la herramienta, verifique ese tipo 6 del atributo: El tipo de servicio capítulo y el tipo 7 del atributo: El Protocolo Entramado es PPP. Si usted observa que los atributos 6 o 7 no están como se muestra, corrija el perfil del usuario en el servidor de RADIUS (refiera a la sección de configuración). También note que el radio del debug muestra un access-accept, que indica que el servidor de RADIUS autenticó con éxito al usuario. Si la salida muestra un Access-Reject, después no autenticaron al usuario y usted debe marcar la configuración del nombre de usuario y contraseña en el servidor de RADIUS. Otro atributo a verificar es el tipo 4 del atributo: Nas-ip-address. Verifique que el valor visualizado por la herramienta del Output Interpreter haga juego la dirección IP NAS configurada en el servidor de RADIUS.

Nota: Debido a las restricciones de Cisco IOS y a las diferencias en la salida de los debugs con diversas versiones, algunos atributos pueden ser truncados (por ejemplo, username, Llamar-estación-ID(DNIS)).

*Apr  5 11:06:19.871: AAA/AUTHEN (2673347869): status = PASS
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/LCP: Authorize LCP
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/LCP (3232903941): Port='Async5' list='' 
service=NET
*Apr  5 11:06:19.871: AAA/AUTHOR/LCP: As5 (3232903941) user='async_client'
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/LCP (3232903941): send AV service=ppp
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/LCP (3232903941): send AV protocol=lcp
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/LCP (3232903941): found list "default"
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/LCP (3232903941): Method=radius (radius)
*Apr  5 11:06:19.871: As5 AAA/AUTHOR (3232903941): Post authorization status 
= PASS_REPL
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/LCP: Processing AV service=ppp
*Apr  5 11:06:19.871: As5 CHAP: O SUCCESS id 1 len 4
*Apr  5 11:06:19.871: As5 PPP: Phase is UP
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/FSM (1882093345): Port='Async5' list='' 
service=NET
*Apr  5 11:06:19.871: AAA/AUTHOR/FSM: As5 (1882093345) user='async_client'
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/FSM (1882093345): send AV service=ppp
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/FSM (1882093345): send AV protocol=ip
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/FSM (1882093345): found list "default"
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/FSM (1882093345): Method=radius (radius)
*Apr  5 11:06:19.871: As5 AAA/AUTHOR (1882093345): Post authorization status 
= PASS_REPL
*Apr  5 11:06:19.871: As5 AAA/AUTHOR/FSM: We can start IPCP
*Apr  5 11:06:19.875: As5 IPCP: O CONFREQ [Closed] id 1 len 10
*Apr  5 11:06:19.875: As5 IPCP:    Address 172.22.53.141 (0x0306AC16358D)
*Apr  5 11:06:19.991: As5 IPCP: I CONFREQ [REQsent] id 1 len 34
*Apr  5 11:06:19.991: As5 IPCP:    Address 0.0.0.0 (0x030600000000)
*Apr  5 11:06:19.991: As5 IPCP:    PrimaryDNS 0.0.0.0 (0x810600000000)
*Apr  5 11:06:19.991: As5 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
*Apr  5 11:06:19.991: As5 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
*Apr  5 11:06:19.991: As5 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
*Apr  5 11:06:19.991: As5 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, 
we want 172.22.53.148

!--- The address for the peer obtained from the pool.

*Apr  5 11:06:19.991: As5 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Apr  5 11:06:19.991: As5 AAA/AUTHOR/IPCP: Authorization succeeded
*Apr  5 11:06:19.991: As5 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, 
we want 172.22.53.148
*Apr  5 11:06:19.991: As5 IPCP: O CONFREJ [REQsent] id 1 len 22
*Apr  5 11:06:19.991: As5 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
*Apr  5 11:06:19.995: As5 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
*Apr  5 11:06:19.995: As5 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
*Apr  5 11:06:20.007: As5 IPCP: I CONFACK [REQsent] id 1 len 10
*Apr  5 11:06:20.007: As5 IPCP:    Address 172.22.53.141 (0x0306AC16358D)
*Apr  5 11:06:20.119: As5 IPCP: I CONFREQ [ACKrcvd] id 2 len 16
*Apr  5 11:06:20.119: As5 IPCP:    Address 0.0.0.0 (0x030600000000)
*Apr  5 11:06:20.119: As5 IPCP:    PrimaryDNS 0.0.0.0 (0x810600000000)
*Apr  5 11:06:20.119: As5 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, 
we want 172.22.53.148
*Apr  5 11:06:20.119: As5 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Apr  5 11:06:20.119: As5 AAA/AUTHOR/IPCP: Authorization succeeded
*Apr  5 11:06:20.119: As5 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, 
we want 172.22.53.148
*Apr  5 11:06:20.119: As5 IPCP: O CONFNAK [ACKrcvd] id 2 len 16
*Apr  5 11:06:20.119: As5 IPCP:    Address 172.22.53.148 (0x0306AC163594)
*Apr  5 11:06:20.119: As5 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
*Apr  5 11:06:20.231: As5 IPCP: I CONFREQ [ACKrcvd] id 3 len 16
*Apr  5 11:06:20.231: As5 IPCP:    Address 172.22.53.148 (0x0306AC163594)
*Apr  5 11:06:20.231: As5 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
*Apr  5 11:06:20.231: As5 AAA/AUTHOR/IPCP: Start.  Her address 172.22.53.148, 
we want 172.22.53.148
*Apr  5 11:06:20.231: As5 AAA/AUTHOR/IPCP (3727543204): Port='Async5' list='' 
service=NET
*Apr  5 11:06:20.231: AAA/AUTHOR/IPCP: As5 (3727543204) user='async_client'
*Apr  5 11:06:20.231: As5 AAA/AUTHOR/IPCP (3727543204): send AV service=ppp
*Apr  5 11:06:20.231: As5 AAA/AUTHOR/IPCP (3727543204): send AV protocol=ip
*Apr  5 11:06:20.231: As5 AAA/AUTHOR/IPCP (3727543204): send AV addr*172.22.53.148
*Apr  5 11:06:20.231: As5 AAA/AUTHOR/IPCP (3727543204): found list "default"
*Apr  5 11:06:20.231: As5 AAA/AUTHOR/IPCP (3727543204): Method=radius (radius)
*Apr  5 11:06:20.235: As5 AAA/AUTHOR (3727543204): Post authorization status 
= PASS_REPL
*Apr  5 11:06:20.235: As5 AAA/AUTHOR/IPCP: Reject 172.22.53.148, 
using 172.22.53.148
*Apr  5 11:06:20.235: As5 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Apr  5 11:06:20.235: As5 AAA/AUTHOR/IPCP: Processing AV addr*172.22.53.148
*Apr  5 11:06:20.235: As5 AAA/AUTHOR/IPCP: Authorization succeeded
*Apr  5 11:06:20.235: As5 AAA/AUTHOR/IPCP: Done.  Her address 172.22.53.148, 
we want 172.22.53.148
*Apr  5 11:06:20.235: As5 IPCP: O CONFACK [ACKrcvd] id 3 len 16
*Apr  5 11:06:20.235: As5 IPCP:    Address 172.22.53.148 (0x0306AC163594)
*Apr  5 11:06:20.235: As5 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
*Apr  5 11:06:20.235: As5 IPCP: State is Open
*Apr  5 11:06:20.235: As5 IPCP: Install route to 172.22.53.148

!--- Route to remote peer is installed.

*Apr  5 11:06:20.871: %LINEPROTO-5-UPDOWN: Line protocol on Interface Async5, 
changed state to up

Información Relacionada


Document ID: 14966