Administración de redes y automatización : Dispositivos de seguridad Cisco PIX de la serie 500

Configuración de PIX para permitir acceso remoto a las carpetas compartidas en un Dominio NT.

17 Octubre 2016 - Traducción Automática
Otras Versiones: PDFpdf | Inglés (22 Agosto 2015) | Comentarios


Contenido


Introducción

Este documento explica cómo configurar Cisco Secure PIX Firewall para permitir el acceso a carpetas compartidas en un dominio NT con el firewall PIX. Puede acceder a los hosts que residen en la interfaz interior PIX mediante la interconexión de redes de Windows. También puede registrarse en el dominio con la misma configuración. La información de configuración en este documento cubre únicamente el dominio Windows NT y no incluye Windows 2000 o Active Directory.

Nota: Un administrador debe evaluar las consecuencias en la seguridad de permitir el tráfico del Windows Networking en cuanto a cualquier política de seguridad corporativa.

Antes de comenzar

Convenciones

Para obtener más información sobre las convenciones del documento, consulte Convenciones de Consejos Técnicos de Cisco.

prerrequisitos

Este documento asume la familiaridad con Microsoft y los principios de red de Windows. Si desea obtener más información, consulte las siguientes referencias:

Esta sección describe cómo configurar el PIX para permitir el siguiente flujo de tráfico cuando un usuario intenta obtener acceso a una carpeta compartida en el dominio NT.

  • Antes de intentar acceder a la carpeta compartida:

    1. La PC que intenta acceder, en primer lugar se registra mediante el servicio de nombre NetBios, utilizando el puerto 137 UDP de origen y destino.

    2. Busca para el controlador de dominio para el dominio usando el tráfico de Netlogon, usando la fuente y el puerto 138 del destino UDP.

  • Mientras accede a la carpeta y la cierra:

    1. Establece una sesión de Sistema de red básico de entrada/salida (NetBIOS) para obtener acceso a la carpeta compartida, con el origen 1024-65536/TCP y el destino 139/TCP.

    2. Termina a la sesión de NetBIOS cuando está acabada.

Componentes Utilizados

Si bien puede utilizar cualquier hardware y software PIX, este documento contempla el desarrollo y las pruebas realizadas con lo siguiente:

  • Software Cisco PIX Firewall versión 6.1(1)

La información que se presenta en este documento se originó a partir de dispositivos dentro de un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener un comando antes de ejecutarlo.

Configuración de su software PIX

Esta sección describe cómo configurar el PIX para permitir el siguiente flujo de tráfico cuando un usuario intenta obtener acceso a una carpeta compartida en el dominio NT.

Diagrama de la red

Este documento utiliza la instalación de red que se muestra en el siguiente diagrama.

/image/gif/paws/18801/pixnetbios-a.gif

Este ejemplo incluye dos hosts internos:

  • 10.48.66.106 - RABIA, que es un controlador de dominio primario (PDC) y un servidor del Windows Naming Service (TRIUNFOS) en este ejemplo.

  • 10.48.66.73 - NPITRN, que es otro host con los recursos o las carpetas a compartir.

El host AYPC reside en la interfaz exterior y tiene una dirección IP de 192.168.10.5. En esta configuración, esta máquina es parte del dominio en la parte interna. Sin embargo, esto no necesita ser el caso para acceder a las carpetas compartidas. Esto difiere desde un inicio de dominio donde la máquina debe pertenecer al dominio o debe existir una relación de confianza.

Para acceder los recursos o las carpetas con el Firewall, usted puede cualquier uso el Universal Naming Convention (UNC), ingresando \ \ resource_name, por ejemplo; o puede hacer doble clic en el icono Network Neighborhood (Entorno de red).

Este ejemplo usa un PIX con dos interfaces, pero el concepto sigue siendo el mismo para cualquier número de interfaces.

Configuración de WINS y PIX Firewall

Utilice los pasos siguientes para configurar WINS y el firewall de PIX.

  1. Configure los TRIUNFOS y verifique la accesibilidad sin el PIX. (opcional)

    Si no lo hizo todavía, configure WINS para la resolución de nombres de NetBIOS.

    En esta configuración en particular, el PDC y el WINS se encuentran en la misma máquina. Esto puede ser diferente en su red. El nombre del dominio en esta configuración es TACWEB y el nombre de la computadora es RAGE. Este ejemplo de laboratorio muestra un intento de acceso a las carpetas compartidas del RAGE y7o NPITRIN. Existe una entrada para el PDC y el host interno NPITRN en el servidor WINS.

    Más detalles en cómo configurar los TRIUNFOS están disponibles en manejo del capítulo de los servidores de los TRIUNFOSleavingcisco.com MS del juego de recursos del Windows NT. Si su servidor de los TRIUNFOS es multihomed, usted necesita configurar las correlaciones estáticas para todos los IP Addresses y configurar la estática apropiada y las Listas de acceso en el PIX. Asegúrese de que los clientes externos estén configurados para resolución de nombres de WINS.

  2. Configure el firewall PIX con las estáticas apropiadas y los conductos/las Listas de acceso (sin el NAT).

    Si su configuración implica el Network Address Translation (NAT), refiera por favor al paso 3 abajo. Solamente las porciones pertinentes de la configuración PIX discutida se muestran aquí. Para los detalles básicos de la configuración PIX, refiera a la sección de información relacionada. La interconexión de redes de Windows utiliza el puerto UDP 137, el puerto UDP 138 y el TCP 139 para diversos servicios NetBIOS necesarios para obtener acceso a carpetas.

    Nota: Este documento utiliza el sintaxis de la lista de acceso PIX que fue introducido en la versión 5.0.1; los conductos se pueden también utilizar, pero no conjuntamente con las Listas de acceso.

    Para permitir el tráfico de una interfaz de menor seguridad a la interfaz de la gran seguridad, defina las Listas de acceso en el PIX.

    pixfirewall(config)# access-list msnet permit tcp any h 10.48.66.106 eq 139 
    pixfirewall(config)# access-list msnet permit udp any h 10.48.66.106 eq 138 
    pixfirewall(config)# access-list msnet permit udp any h 10.48.66.106 eq 137 
    pixfirewall(config)# access-list msnet permit tcp any h 10.48.66.73 eq 139 
    pixfirewall(config)# access-list msnet permit udp any h 10.48.66.73 eq 138 
    pixfirewall(config)# access-list msnet permit udp any h 10.48.66.73 eq 137 
    
    
    pixfirewall(config)# show access-list 
    access-list msnet permit tcp any host 10.48.66.73 eq 139 (hitcnt=0) 
    access-list msnet permit udp any host 10.48.66.73 eq netbios-dgm (hitcnt=0) 
    access-list msnet permit udp any host 10.48.66.73 eq netbios-ns (hitcnt=0) 
    access-list msnet permit tcp any host 10.48.66.106 eq 139 (hitcnt=0) 
    access-list msnet permit udp any host 10.48.66.106 eq netbios-dgm (hitcnt=0) 
    access-list msnet permit udp any host 10.48.66.106 eq netbios-ns (hitcnt=0)

    Como usted puede ver, el PIX substituye los números del puerto por los nombres bien conocidos del servicio. Por cada host de la parte interna al que quiera acceder de manera remota, tiene que abrir PIX para los servicios NetBIOS de Windows, tal como se muestra anteriormente. La excepción es cuando define una estática de red, que integra todos los host de su red interna y permite el acceso a toda la subred.

    Nota: Todos los recursos que usted quiere para acceder remotamente la necesidad de tener IP estático una asignación y no puede para utilizar el Protocolo de configuración dinámica de host (DHCP). Configure las IP estáticas apropiadas y verifíquelas.

    pixfirewall(config)# show stat 
    static (inside,outside) 10.48.66.106 10.48.66.106 netmask 255.255.255.255 0 0 
    static (inside,outside) 10.48.66.73 10.48.66.73 netmask 255.255.255.255 0 0
  3. Configure el firewall PIX con el NAT. (si es necesario)

    Nota: Esta sección se aplica solamente a las configuraciones PIX con el NAT implicado. Si NAT no está involucrado, compruebe que haya realizado el paso 1 y el paso 2 más arriba y luego vaya a Verificación de la accesibilidad a través de PIX Firewall.

    Si NAT está involucrado, tenga en cuenta los dos siguientes factores:

    • Configure el servidor de los TRIUNFOS de modo que pueda devolver el traducido y a los IP Address internos al cliente de los TRIUNFOS. Para hacer esto, seleccione al Grupo de Internet como la opción del tipo en el cuadro de diálogo de las correlaciones estáticas del agregar del administrador de los TRIUNFOS. La opción de Grupo de Internet definida por el usuario le permite especificar hasta 25 direcciones para un solo nombre.

      Cuando el cliente de los TRIUNFOS hace la resolución de nombre del NetBios con el servidor de los TRIUNFOS, GANA las devoluciones de los direccionamientos y el cliente puede establecer a la sesión de NetBIOS con el recurso en la pregunta.

    • La configuración PIX necesita reflejar las Listas de acceso apropiadas y el statics. Por ejemplo, con la misma configuración pero con una NAT, la configuración sería:

      static (inside,outside) 192.168.10.50 10.48.66.106 netmask 255.255.255.255 0 0 
      static (inside,outside) 192.168.10.60 10.48.66.73 netmask 255.255.255.255 0 0 
      access-list msnet permit tcp any host 192.168.10.50 eq 139 
      access-list msnet permit udp any host 192.168.10.50 eq netbios-dgm 
      access-list msnet permit udp any host 192.168.10.50 eq netbios-ns 
      access-list msnet permit tcp any host 192.168.10.60 eq 139 
      access-list msnet permit udp any host 192.168.10.60 eq netbios-dgm 
      access-list msnet permit udp any host 192.168.10.60 eq netbios-ns 
      access-list msnet permit icmp any any 
      access-group msnet in interface outside

Verificación

Verificación de la accesibilidad a través de PIX Firewall

Utilice los pasos siguientes para verificar la accesibilidad a través de un escudo de protección PIX.

Nota: Antes de continuar con los pasos de verificación, asegúrese de poder ejecutar un ping en los recursos interiores (hosts RAGE y NPITRN en este ejemplo) a fin de evitar problemas relacionados con cualquier problema de conectividad IP básica. Usted puede configurar una lista de acceso o el conducto para permitir el ping y posterior lo quita si su política de seguridad no permite el tráfico de ping.

  1. Active la depuración en el firewall PIX para ver el flujo de paquetes.

    pixfirewall(config)# logging on 
    pixfirewall(config)# logging console debug
    
  2. Verifique las configuraciones usando el comando show logging:

    pixfirewall(config)# show logging
    <snip>
       Console logging: level debugging, 25 messages logged 
    <snip>
    
    pixfirewall(config)# show xlate 
    0 in use, 45 most used 
    
  3. Intente reiniciar la PC y acceda a los recursos utilizando UNC. En la computadora remota, la Computadora selecta del comienzo > del hallazgo y teclea el nombre del recurso que usted quiere acceder. En este ejemplo, NPITRN es este recurso.

  4. Reinicie la PC por fuera (AYPC en este ejemplo). Mientras AYPC se inicia, vemos las siguientes depuraciones en PIX. Esto se espera y es parte de la descripción general del flujo de paquetes que se describió anteriormente.

    pixfirewall(config)# 
    609001: Built local-host inside:10.48.66.106 
    305002: Translation built for gaddr 10.48.66.106 to laddr 10.48.66.106 
    302005: Built UDP connection for faddr 192.168.10.5/137 gaddr 10.48.66.106/137 
    laddr 10.48.66.106/137 
    302005: Built UDP connection for faddr 192.168.10.5/138 gaddr 10.48.66.106/138 
    laddr 10.48.66.106/138 
    302001: Built inbound TCP connection 420 for faddr 192.168.10.5/1027 
    gaddr 10.48.66.106/139 laddr 10.48.66.106/139 
    302001: Built inbound TCP connection 421 for faddr 192.168.10.5/1032 
    gaddr 10.48.66.106/139 laddr 10.48.66.106/139 
    pixfirewall(config)# 302006: Teardown UDP connection for faddr 192.168.10.5/138 
    gaddr 10.48.66.106/138 laddr 10.48.66.106/138 
    pixfirewall(config)#show xlate 
    1 in use, 45 most used 
    Global 10.48.66.106 Local 10.48.66.106 static 
    pixfirewall(config)# show conn 
    3 in use, 12 most used 
    TCP out 192.168.10.5:1027 in 10.48.66.106:139 idle 0:01:41 Bytes 23514 
    flags UIOB 
    TCP out 192.168.10.5:1032 in 10.48.66.106:139 idle 0:02:29 Bytes 1302 
    flags UIOB 
    UDP out 192.168.10.5:137 in 10.48.66.106:137 idle 0:00:56 flags

Procedimiento de Troubleshooting

Información sobre resolución de problemas y ejemplo de rastro del sabueso

La siguiente información tiene el propósito de ayudarlo a solucionar problemas y obtener información sobre su configuración.

Microsoft Networking usa el protocolo de Bloqueo de mensajes del servidor (SMB) para los servicios de intercambio de archivos e impresión de Windows. ¿Para una introducción al SMB, visite apenas cuál es SMB?leavingcisco.com .

Si usted recibe el trayecto de red no era diálogo encontrado del mensaje de error cuando usted intenta acceder la carpeta usando \ \ resource_name:

  • Es probable que el servidor WINS no responda a la petición del cliente para resolver el nombre NetBIOS. Cuando sucede esto, el cliente revisa pero si no hay respuesta, recurrirá para transmitir en el segmento local. Porque el PIX bloquea los broadcasts (esto no puede ser cambiada), la resolución de nombre fallará. Eventualmente, esto provocará el mensaje de error mencionado.

    Para solucionar este problema, controle por qué el servidor WINS no responde y arréglelo. Intente capturar una traza de sniffer para ver si están respondiendo los TRIUNFOS y si el paquete está haciendo su manera de nuevo al cliente. Corrija el problema, de modo de que el paquete llegue al cliente.

Si su servidor de los TRIUNFOS es multihomed, verifique las correlaciones estáticas en el administrador de los TRIUNFOS y verifiquelas que los parásitos atmosféricos y las Listas de acceso existan para todos los IP Addresses implicados.

A continuación, se brinda un ejemplo de los rastros del sabueso de quince tramas para una conexión en funcionamiento. Utilícelo como seguimiento de la línea de base al resolver problemas similares.

  • Las tramas 1 a 6 muestran el proceso de registro de nombres que se lleva a cabo entre el cliente y el servidor WINS.

  • Las tramas 7-8 muestran el proceso NetLogon (el cliente que busca un DC) entre el cliente y el servidor WINS.

  • Las tramas 9-11 muestra el establecimiento de sesión del TCP.

  • La trama 12-13 muestra el establecimiento de sesión de NetBIOS.

  • La trama 14-15 muestra el inicio de la negociación SMB y cómo el proceso continúa y termina cuando un usuario finalizó su acceso al recurso.

    Nota: Debido a las limitaciones de espacio, se ha adaptado este seguimiento de sabueso al tamaño de la pantalla.

- - - - - - - - - - - - - - - - - - - - Frame 1 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source           
 \",\"Bytes\",\"Protocol  \",\"Summary\" 
"    M ","     1","0.000.000    ","RAGE              ","AYPC              ","   
92 ","WINS"," C ID=32860 OP=QUERY NAME=TACWEB<1C>" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 1 arrived at  12:58:27.6668; frame size is 92 (005C hex) bytes. 
      DLC:  Destination = Station 001083027B34 
      DLC:  Source      = Station 005054FEEA31 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 78 bytes 
      IP: Identification  = 5889 
      IP: Flags           = 0X 
      IP:       .0.. .... = may fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 17 (UDP) 
      IP: Header checksum = 0C57 (correct) 
      IP: Source address      = [192.168.10.5], AYPC 
      IP: Destination address = [10.48.66.106], RAGE 
      IP: No options 
      IP: 
UDP: ----- UDP Header ----- 
      UDP: 
      UDP: Source port      = 137 (NetBIOS-ns) 
      UDP: Destination port = 137 (NetBIOS-ns) 
      UDP: Length           = 58 
      UDP: Checksum         = 0F61 (correct) 
      UDP: [50 byte(s) of data] 
      UDP: 
WINS: ----- WINS Name Service header ----- 
      WINS: 
      WINS: ID = 32860 
      WINS: Flags = 01 
      WINS: 0... .... = Command 
      WINS: .000 0...   = Query 
      WINS: .... ..0. = Not truncated 
      WINS: .... ...1 = Recursion desired 
      WINS: Flags = 0X 
      WINS: ...0 .... = Non Verified data NOT acceptable 
      WINS: Question count = 1, Answer count = 0 
      WINS: Authority count = 0, Additional record count = 0 
      WINS: 
      WINS: Question section: 
      WINS:     Name = TACWEB<1C>  
      WINS:     Type = NetBIOS name service (WINS) (NetBIOS name,32) 
      WINS:     Class = Internet (IN,1) 
      WINS: 
- - - - - - - - - - - - - - - - - - - - Frame 2 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source         
   \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","     2","0.000.582    ","AYPC              ","RAGE              "," 
 110 ","WINS"," R ID=32860 STAT=OK " 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 2 arrived at  12:58:27.6674; frame size is 110 (006E hex) bytes. 
      DLC:  Destination = Station 005054FEEA31 
      DLC:  Source      = Station 001083027B34 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 96 bytes 
      IP: Identification  = 49634 
      IP: Flags           = 0X 
      IP:       .0.. .... = may fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 17 (UDP) 
      IP: Header checksum = 6163 (correct) 
      IP: Source address      = [10.48.66.106], RAGE 
      IP: Destination address = [192.168.10.5], AYPC 
      IP: No options 
      IP: 
UDP: ----- UDP Header ----- 
      UDP: 
      UDP: Source port      = 137 (NetBIOS-ns) 
      UDP: Destination port = 137 (NetBIOS-ns) 
      UDP: Length           = 76 
      UDP: Checksum         = A5AB (correct) 
      UDP: [68 byte(s) of data] 
      UDP: 
WINS: ----- WINS Name Service header ----- 
      WINS: 
      WINS: ID = 32860 
      WINS: Flags = 85 
      WINS: 1... .... = Response 
      WINS: .... .1.. = Authoritative answer 
      WINS: .000 0...   = Query 
      WINS: .... ..0. = Not truncated 
      WINS: Flags = 8X 
      WINS: ..0. .... = Data NOT verified 
      WINS: 1... .... = Recursion available 
      WINS: Response code = OK (0) 
      WINS: ...0 .... = Unicast packet 
      WINS: Question count = 0, Answer count = 1 
      WINS: Authority count = 0, Additional record count = 0 
      WINS: 
      WINS: Answer section: 
      WINS:     Name = TACWEB<1C>  
      WINS:     Type = NetBIOS name service (WINS) (NetBIOS name,32) 
      WINS:     Class = Internet (IN,1) 
      WINS:     Time-to-live = 0 (seconds) 
      WINS:     Length = 12 
      WINS: Node flags = 80 
      WINS:  1... .... = Group NetBIOS name 
      WINS:  .00. ....   = B-type node 
      WINS: Node address = [10.48.66.106], RAGE 
      WINS: Node flags = 80 
      WINS:  1... .... = Group NetBIOS name 
      WINS:  .00. ....   = B-type node 
      WINS: Node address = [144.254.7.107] 
      WINS: 

- - - - - - - - - - - - - - - - - - - - Frame 3 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source            
\",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","     3","0.002.317    ","RAGE              ","AYPC              ","  308 
","NETLOGON"," SAM LOGON Request from client" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 3 arrived at  12:58:27.6697; frame size is 308 (0134 hex) bytes. 
      DLC:  Destination = Station 001083027B34 
      DLC:  Source      = Station 005054FEEA31 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 294 bytes 
      IP: Identification  = 6401 
      IP: Flags           = 0X 
      IP:       .0.. .... = may fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 17 (UDP) 
      IP: Header checksum = 097F (correct) 
      IP: Source address      = [192.168.10.5], AYPC 
      IP: Destination address = [10.48.66.106], RAGE 
      IP: No options 
      IP: 
UDP: ----- UDP Header ----- 
      UDP: 
      UDP: Source port      = 138 (NetBIOS-dgm) 
      UDP: Destination port = 138 (NetBIOS-dgm) 
      UDP: Length           = 274 
      UDP: Checksum         = 627C (correct) 
      UDP: [266 byte(s) of data] 
      UDP: 
NETB: ----- NetBIOS Datagram protocol ----- 
      NETB: 
      NETB: Type = 17 (Direct_group datagram) 
      NETB: Flags = 1A 
      NETB: .... ..1. = First packet 
      NETB: .... ...0 = No more to follow 
      NETB: Datagram ID = 805A 
      NETB: Source node = [192.168.10.5], AYPC 
      NETB: Port = 138 
      NETB: Total datagram length (including names) = 252 
      NETB: Packet offset = 0 
      NETB:      Source NetBIOS name = AYPC<00>  
      NETB: Destination NetBIOS name = TACWEB<1C>  
      NETB: Total datagram length (excluding names) = 184 
      NETB: 
SMB: ----- SMB (CIFS) Transaction Command header ----- 
      SMB: 
      SMB: SMB Constant 
      SMB: Command            = 25 (Transaction) 
      SMB: Reserved           = 0 
      SMB: Flags = 18 
      SMB: 0... .... = Client Command 
      SMB: ..0. .... = No Opportunistic file Locking 
      SMB: ...1 .... = Pathnames are already in canonicalized format 
      SMB: .... 1... = Pathnames should be treated as caseless 
      SMB: .... ..0. = Send.No.Ack can not be used as a response 
      SMB: .... ...0 = Doesn't support Lock&Read, Write&Unlock
      SMB: Flags2 = 0003 
      SMB:  0... ....  .... .... = STRING type is ASCIIZ 
      SMB:  .0.. ....  .... .... = DOS style Error code 
      SMB:  ..0. ....  .... .... = No Paging IO 
      SMB:  ...0 ....  .... .... = No DFS support 
      SMB:  .... 0...  .... .... = Client not aware of extended security 
      SMB:  .... ....  .... .0.. = Don't use message authentication 
      SMB:  .... ....  .... ..1. = Client supports extended attributes 
      SMB:  .... ....  .... ...1 = Client supports Long file names 
      SMB: Reserved2(MBZ)     = 000000000000000000000000 
      SMB: Tree ID            = 0000 
      SMB: Process ID         = CAFE 
      SMB: Unauth User ID     = 0000 
      SMB: Multiplex ID       = 0000 
      SMB: 
      SMB: ----- Transaction Header ----- 
      SMB: 
      SMB: Word count         = 17 
      SMB: Parameter words    = 00005C000200000000000200FFFFFFFF000000005C005C005C0
00300010000000200 
      SMB: Byte Count         = 115 
      SMB: Byte parameters    = 5C4D41494C534C4F545C4E45545C4E544C4F474F4E000012000
000410059005000430000004100590050004300240000005C4D41494C534C4F545C4E45545C47455444
43303432008000000018000000000000010400000000000515000000221A8324C44B14687144060B010
00000... 
      SMB: Total parameter bytes being sent = 0 
      SMB: Total data bytes being sent      = 92 
      SMB: Max number of parameter bytes to return  = 2 
      SMB: Max number of data bytes to return       = 0 
      SMB: Max number of Setup words to return      = 0 
      SMB: Reserved(MBZ)                            = 00 
      SMB: Additional information                   = 0002 
      SMB:  ........ ......1. = One way transaction 
      SMB:  ........ .......0 = Preserve TID 
      SMB: Timeout to completion                    = Indefinite wait 
      SMB: Reserved(MBZ)                            = 0000 
      SMB: Number of parameter bytes in this buffer = 0 
      SMB: Offset from header to parameter bytes    = 92 
      SMB: Number of data bytes in this buffer = 92 
      SMB: Offset from header to data bytes    = 92 
      SMB: Setup word count = 3 
      SMB: Reserved(MBZ)    = 00 
      SMB: Setup words      = 010000000200 
      SMB: Byte Count                      = 115 
      SMB: Transaction name = \MAILSLOT\NET\NTLOGON 
      SMB: Data bytes       = 120000004100590050004300000041005900500043002400000
05C4D41494C534C4F545C4E45545C4745544443303432008000000018000000000000010400000000
000515000000221A8324C44B14687144060B01000000FFFFFFFF 
      SMB: 
SMBMSP: ----- SMB MAILSLOTS Protocol ----- 
      SMBMSP: 
      SMBMSP: Op code = 1 (Write mail slot) 
      SMBMSP: Priority of transaction = 0 
      SMBMSP: Class of service = 2 (Unreliable & broadcast) 
      SMBMSP: Total size of mail data = 115 
      SMBMSP: MAILSLOT = "\MAILSLOT\NET\NTLOGON" 
      SMBMSP: 
NETLOGON: ----- SMB NETLOGON Protocol ----- 
      NETLOGON: 
      NETLOGON: NETLOGON Command      =  12  (SAM LOGON Request from client) 
      NETLOGON: Request Count         = 0 (0x0000) 
      NETLOGON: Unicode Computer Name = AYPC 
      NETLOGON: Unicode User Name     = AYPC$ 
      NETLOGON: MailSlot Name         = "\MAILSLOT\NET\GETDC042" 
      NETLOGON: Allowable Account control bits  = 00000080 
      NETLOGON:  ........ ........  .....0.. ........ = User account not 
auto-locked 
      NETLOGON:  ........ ........  ......0. ........ = User Password will 
expire 
      NETLOGON:  ........ ........  .......0 ........ = Not a Server Trust 
user account 
      NETLOGON:  ........ ........  ........ 1....... = Workstation Trust 
user account 
      NETLOGON:  ........ ........  ........ .0...... = Not an Inter-domain 
Trust user account 
      NETLOGON:  ........ ........  ........ ..0..... = Not a MNS Logon user 
account 
      NETLOGON:  ........ ........  ........ ...0.... = Not a normal user 
account 
      NETLOGON:  ........ ........  ........ ....0... = Not a temp duplicate 
user account 
      NETLOGON:  ........ ........  ........ .....0.. = User password required 
      NETLOGON:  ........ ........  ........ ......0. = User Home directory not 
required 
      NETLOGON:  ........ ........  ........ .......0 = User account enabled 
      NETLOGON: Domain SID Size       = 24 (0x00000018) 
      NETLOGON: SID                   = 000000010400000000000515000000221A8324
C44B146871 
      NETLOGON:
- - - - - - - - - - - - - - - - - - - - Frame 4 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source       
     \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","     4","0.000.900    ","AYPC              ","RAGE              "," 
 266 ","NETLOGON"," SAM Response to SAM LOGON Request" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 4 arrived at  12:58:27.6706; frame size is 266 (010A hex) bytes. 
      DLC:  Destination = Station 005054FEEA31 
      DLC:  Source      = Station 001083027B34 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 252 bytes 
      IP: Identification  = 49890 
      IP: Flags           = 0X 
      IP:       .0.. .... = may fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 17 (UDP) 
      IP: Header checksum = 5FC7 (correct) 
      IP: Source address      = [10.48.66.106], RAGE 
      IP: Destination address = [192.168.10.5], AYPC 
      IP: No options 
      IP: 
UDP: ----- UDP Header ----- 
      UDP: 
      UDP: Source port      = 138 (NetBIOS-dgm) 
      UDP: Destination port = 138 (NetBIOS-dgm) 
      UDP: Length           = 232 
      UDP: Checksum         = D678 (correct) 
      UDP: [224 byte(s) of data] 
      UDP: 
NETB: ----- NetBIOS Datagram protocol ----- 
      NETB: 
      NETB: Type = 16 (Direct_unique datagram) 
      NETB: Flags = 1A 
      NETB: .... ..1. = First packet 
      NETB: .... ...0 = No more to follow 
      NETB: Datagram ID = 8FEE 
      NETB: Source node = [10.48.66.106], RAGE 
      NETB: Port = 138 
      NETB: Total datagram length (including names) = 210 
      NETB: Packet offset = 0 
      NETB:      Source NetBIOS name = RAGE<00>  
      NETB: Destination NetBIOS name = AYPC<00>  
      NETB: Total datagram length (excluding names) = 142 
      NETB: 
SMB: ----- SMB (CIFS) Transaction Command header ----- 
      SMB: 
      SMB: SMB Constant 
      SMB: Command            = 25 (Transaction) 
      SMB: Reserved           = 0 
      SMB: Flags = 00 
      SMB: 0... .... = Client Command 
      SMB: ..0. .... = No Opportunistic file Locking 
      SMB: ...0 .... = Pathnames are not in canonicalized format 
      SMB: .... 0... = Pathnames are case sensitive 
      SMB: .... ..0. = Send.No.Ack can not be used as a response 
      SMB: .... ...0 = Doesn't support Lock&Read, Write&Unlock
      SMB: Flags2 = 0000 
      SMB:  0... ....  .... .... = STRING type is ASCIIZ 
      SMB:  .0.. ....  .... .... = DOS style Error code 
      SMB:  ..0. ....  .... .... = No Paging IO 
      SMB:  ...0 ....  .... .... = No DFS support 
      SMB:  .... 0...  .... .... = Client not aware of extended security 
      SMB:  .... ....  .... .0.. = Don't use message authentication 
      SMB:  .... ....  .... ..0. = Client does not support extended attributes 
      SMB:  .... ....  .... ...0 = Client does not support Long file names 
      SMB: Reserved2(MBZ)     = 000000000000000000000000 
      SMB: Tree ID            = 0000 
      SMB: Process ID         = 0000 
      SMB: Unauth User ID     = 0000 
      SMB: Multiplex ID       = 0000 
      SMB: 
      SMB: ----- Transaction Header ----- 
      SMB: 
      SMB: Word count         = 17 
      SMB: Parameter words    = 000032000000000000000000E80300000000000000003200
5C000300010001000200 
      SMB: Byte Count         = 73 
      SMB: Byte parameters    = 5C4D41494C534C4F545C4E45545C47455444433034320013
005C005C005200410047004500000041005900500043002400000054004100430057004500420000
0001000000FFFFFFFF 
      SMB: Total parameter bytes being sent = 0 
      SMB: Total data bytes being sent      = 50 
      SMB: Max number of parameter bytes to return  = 0 
      SMB: Max number of data bytes to return       = 0 
      SMB: Max number of Setup words to return      = 0 
      SMB: Reserved(MBZ)                            = 00 
      SMB: Additional information                   = 0000 
      SMB:  ........ ......0. = Two way transaction 
      SMB:  ........ .......0 = Preserve TID 
      SMB: Timeout to completion                    = 1000 (Milliseconds) 
00:00:01.0(HH:MM:SS.MS) 
      SMB: Reserved(MBZ)                            = 0000 
      SMB: Number of parameter bytes in this buffer = 0 
      SMB: Offset from header to parameter bytes    = 0 
      SMB: Number of data bytes in this buffer = 50 
      SMB: Offset from header to data bytes    = 92 
      SMB: Setup word count = 3 
      SMB: Reserved(MBZ)    = 00 
      SMB: Setup words      = 010001000200 
      SMB: Byte Count                      = 73 
      SMB: Transaction name = \MAILSLOT\NET\GETDC042 
      SMB: Data bytes       = 13005C005C0052004100470045000000410059005000430
024000000540041004300570045004200000001000000FFFFFFFF 
      SMB: 
SMBMSP: ----- SMB MAILSLOTS Protocol ----- 
      SMBMSP: 
      SMBMSP: Op code = 1 (Write mail slot) 
      SMBMSP: Priority of transaction = 1 
      SMBMSP: Class of service = 2 (Unreliable & broadcast) 
      SMBMSP: Total size of mail data = 73 
      SMBMSP: MAILSLOT = "\MAILSLOT\NET\GETDC042" 
      SMBMSP: 
NETLOGON: ----- SMB NETLOGON Protocol ----- 
      NETLOGON: 
      NETLOGON: NETLOGON Command      =  13  (SAM Response to SAM LOGON Request) 
      NETLOGON: Unicode Logon Server = \\RAGE 
      NETLOGON: Unicode User Name    = AYPC$ 
      NETLOGON: Unicode Domain Name  = TACWEB 
      NETLOGON: NT Version        = 1 (0x00000001) 
      NETLOGON: LMNT Token        = 0xFFFF 
      NETLOGON: LM20 Token        = 0xFFFF (Lan Manager 2.0 or higher) 
      NETLOGON: 

- - - - - - - - - - - - - - - - - - - - Frame 5 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source         
   \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","     5","1.755.851    ","RAGE              ","AYPC              "," 
 110 ","WINS"," C ID=32862 OP=REGISTER NAME=ADMINISTRATOR<03>" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 5 arrived at  12:58:29.4265; frame size is 110 (006E hex) bytes. 
      DLC:  Destination = Station 001083027B34 
      DLC:  Source      = Station 005054FEEA31 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 96 bytes 
      IP: Identification  = 6913 
      IP: Flags           = 0X 
      IP:       .0.. .... = may fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 17 (UDP) 
      IP: Header checksum = 0845 (correct) 
      IP: Source address      = [192.168.10.5], AYPC 
      IP: Destination address = [10.48.66.106], RAGE 
      IP: No options 
      IP: 
UDP: ----- UDP Header ----- 
      UDP: 
      UDP: Source port      = 137 (NetBIOS-ns) 
      UDP: Destination port = 137 (NetBIOS-ns) 
      UDP: Length           = 76 
      UDP: Checksum         = 3663 (correct) 
      UDP: [68 byte(s) of data] 
      UDP: 
WINS: ----- WINS Name Service header ----- 
      WINS: 
      WINS: ID = 32862 
      WINS: Flags = 29 
      WINS: 0... .... = Command 
      WINS: .010 1...   = Registration 
      WINS: .... ..0. = Not truncated 
      WINS: .... ...1 = Recursion desired 
      WINS: Flags = 0X 
      WINS: ...0 .... = Non Verified data NOT acceptable 
      WINS: Question count = 1, Answer count = 0 
      WINS: Authority count = 0, Additional record count = 1 
      WINS: 
      WINS: Question section: 
      WINS:     Name = ADMINISTRATOR<03>  
      WINS:     Type = NetBIOS name service (WINS) (NetBIOS name,32) 
      WINS:     Class = Internet (IN,1) 
      WINS: 
      WINS: Additional record section: 
      WINS:     Name = ADMINISTRATOR<03>  
      WINS:     Type = NetBIOS name service (WINS) (NetBIOS name,32) 
      WINS:     Class = Internet (IN,1) 
      WINS:     Time-to-live = 300000 (seconds) 
      WINS:     Length = 6 
      WINS: Node flags = 60 
      WINS:  0... .... = Unique NetBIOS name 
      WINS:  .11. ....   = H-type node 
      WINS: Node address = [192.168.10.5], AYPC 
      WINS: 

- - - - - - - - - - - - - - - - - - - - Frame 6 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source      
      \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","     6","0.001.987    ","AYPC              ","RAGE              ","
  104 ","WINS"," R ID=32862 STAT=OK " 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 6 arrived at  12:58:29.4285; frame size is 104 (0068 hex) bytes. 
      DLC:  Destination = Station 005054FEEA31 
      DLC:  Source      = Station 001083027B34 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 90 bytes 
      IP: Identification  = 50146 
      IP: Flags           = 0X 
      IP:       .0.. .... = may fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 17 (UDP) 
      IP: Header checksum = 5F69 (correct) 
      IP: Source address      = [10.48.66.106], RAGE 
      IP: Destination address = [192.168.10.5], AYPC 
      IP: No options 
      IP: 
UDP: ----- UDP Header ----- 
      UDP: 
      UDP: Source port      = 137 (NetBIOS-ns) 
      UDP: Destination port = 137 (NetBIOS-ns) 
      UDP: Length           = 70 
      UDP: Checksum         = 1CFA (correct) 
      UDP: [62 byte(s) of data] 
      UDP: 
WINS: ----- WINS Name Service header ----- 
      WINS: 
      WINS: ID = 32862 
      WINS: Flags = AD 
      WINS: 1... .... = Response 
      WINS: .... .1.. = Authoritative answer 
      WINS: .010 1...   = Registration 
      WINS: .... ..0. = Not truncated 
      WINS: Flags = 8X 
      WINS: ..0. .... = Data NOT verified 
      WINS: 1... .... = Recursion available 
      WINS: Response code = OK (0) 
      WINS: ...0 .... = Unicast packet 
      WINS: Question count = 0, Answer count = 1 
      WINS: Authority count = 0, Additional record count = 0 
      WINS: 
      WINS: Answer section: 
      WINS:     Name = ADMINISTRATOR<03>  
      WINS:     Type = NetBIOS name service (WINS) (NetBIOS name,32) 
      WINS:     Class = Internet (IN,1) 
      WINS:     Time-to-live = 518400 (seconds) 
      WINS:     Length = 6 
      WINS: Node flags = 60 
      WINS:  0... .... = Unique NetBIOS name 
      WINS:  .11. ....   = H-type node 
      WINS: Node address = [192.168.10.5], AYPC 
      WINS: 

- - - - - - - - - - - - - - - - - - - - Frame 7 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source     
       \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","     7","32.953.258   ","RAGE              ","AYPC              ","
   60 ","TCP"," D=139 S=1037 SYN SEQ=39758 LEN=0 WIN=8192" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 7 arrived at  12:59:02.3817; frame size is 60 (003C hex) bytes. 
      DLC:  Destination = Station 001083027B34 
      DLC:  Source      = Station 005054FEEA31 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 44 bytes 
      IP: Identification  = 7425 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = C683 (correct) 
      IP: Source address      = [192.168.10.5], AYPC 
      IP: Destination address = [10.48.66.106], RAGE 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 1037 
      TCP: Destination port        = 139 (NetBIOS-ssn) 
      TCP: Initial sequence number = 39758 
      TCP: Next expected Seq number= 39759 
      TCP: Data offset             = 24 bytes 
      TCP: Flags                   = 02 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...0 .... = (No acknowledgment) 
      TCP:               .... 0... = (No push) 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..1. = SYN 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 8192 
      TCP: Checksum                = 756A (correct) 
      TCP: 
      TCP: Options follow 
      TCP: Maximum segment size = 1380 
      TCP: 

 - - - - - - - - - - - - - - - - - - - - Frame 8 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source        
    \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","     8","0.000.138    ","AYPC              ","RAGE              ","  
 60 ","TCP"," D=1037 S=139 SYN ACK=39759 SEQ=590101 LEN=0 WIN=8280" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 8 arrived at  12:59:02.3819; frame size is 60 (003C hex) bytes. 
      DLC:  Destination = Station 005054FEEA31 
      DLC:  Source      = Station 001083027B34 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 44 bytes 
      IP: Identification  = 50402 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = 1EA2 (correct) 
      IP: Source address      = [10.48.66.106], RAGE 
      IP: Destination address = [192.168.10.5], AYPC 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 139 (NetBIOS-ssn) 
      TCP: Destination port        = 1037 
      TCP: Initial sequence number = 590101 
      TCP: Next expected Seq number= 590102 
      TCP: Acknowledgment number   = 39759 
      TCP: Data offset             = 24 bytes 
      TCP: Flags                   = 12 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...1 .... = Acknowledgment 
      TCP:               .... 0... = (No push) 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..1. = SYN 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 8280 
      TCP: Checksum                = BF71 (correct) 
      TCP: 
      TCP: Options follow 
      TCP: Maximum segment size = 1460 
      TCP: 

- - - - - - - - - - - - - - - - - - - - Frame 9 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source        
    \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","     9","0.001.778    ","RAGE              ","AYPC              "," 
  60 ","TCP"," D=139 S=1037     ACK=590102 WIN=8280" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 9 arrived at  12:59:02.3836; frame size is 60 (003C hex) bytes. 
      DLC:  Destination = Station 001083027B34 
      DLC:  Source      = Station 005054FEEA31 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 40 bytes 
      IP: Identification  = 7681 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = C587 (correct) 
      IP: Source address      = [192.168.10.5], AYPC 
      IP: Destination address = [10.48.66.106], RAGE 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 1037 
      TCP: Destination port        = 139 (NetBIOS-ssn) 
      TCP: Sequence number         = 39759 
      TCP: Next expected Seq number= 39759 
      TCP: Acknowledgment number   = 590102 
      TCP: Data offset             = 20 bytes 
      TCP: Flags                   = 10 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...1 .... = Acknowledgment 
      TCP:               .... 0... = (No push) 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..0. = (No SYN) 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 8280 
      TCP: Checksum                = D72E (correct) 
      TCP: No TCP options 
      TCP: 

- - - - - - - - - - - - - - - - - - - - Frame 10 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source        
    \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","    10","0.000.222    ","RAGE              ","AYPC              "," 
 126 ","NETB"," D=RAGE<20> S=AYPC<00> Session request" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 10 arrived at  12:59:02.3839; frame size is 126 (007E hex) bytes. 
      DLC:  Destination = Station 001083027B34 
      DLC:  Source      = Station 005054FEEA31 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 112 bytes 
      IP: Identification  = 7937 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = C43F (correct) 
      IP: Source address      = [192.168.10.5], AYPC 
      IP: Destination address = [10.48.66.106], RAGE 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 1037 
      TCP: Destination port        = 139 (NetBIOS-ssn) 
      TCP: Sequence number        = 39759 
      TCP: Next expected Seq number= 39831 
      TCP: Acknowledgment number   = 590102 
      TCP: Data offset             = 20 bytes 
      TCP: Flags                   = 18 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...1 .... = Acknowledgment 
      TCP:               .... 1... = Push 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..0. = (No SYN) 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 8280 
      TCP: Checksum                = D120 (correct) 
      TCP: No TCP options 
      TCP: [72 Bytes of data] 
      TCP: 
NETB: ----- NetBIOS Session protocol ----- 
      NETB: 
      NETB: Type = 81 (Session request) 
      NETB: Flags = 00 
      NETB: Total session packet length = 68 
      NETB:  Called NetBIOS name = RAGE<20> <server service>
NETB: Calling NetBIOS name = AYPC<00>
      NETB: 

- - - - - - - - - - - - - - - - - - - - Frame 11 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source        
    \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","    11","0.000.125    ","AYPC              ","RAGE              ","  
 60 ","NETB"," Session confirm" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 11 arrived at  12:59:02.3840; frame size is 60 (003C hex) bytes. 
      DLC:  Destination = Station 005054FEEA31 
      DLC:  Source      = Station 001083027B34 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 44 bytes 
      IP: Identification  = 50658 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = 1DA2 (correct) 
      IP: Source address      = [10.48.66.106], RAGE 
      IP: Destination address = [192.168.10.5], AYPC 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 139 (NetBIOS-ssn) 
      TCP: Destination port        = 1037 
      TCP: Sequence number         = 590102 
      TCP: Next expected Seq number= 590106 
      TCP: Acknowledgment number   = 39831 
      TCP: Data offset             = 20 bytes 
      TCP: Flags                   = 18 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...1 .... = Acknowledgment 
      TCP:               .... 1... = Push 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..0. = (No SYN) 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 8208 
      TCP: Checksum                = 5522 (correct) 
      TCP: No TCP options 
      TCP: [4 Bytes of data] 
      TCP: 
NETB: ----- NetBIOS Session protocol ----- 
      NETB: 
      NETB: Type = 82 (Positive response) 
      NETB: Flags = 00 
      NETB: Total session packet length = 0 
      NETB: 

- - - - - - - - - - - - - - - - - - - - Frame 12 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source        
    \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","    12","0.001.427    ","RAGE              ","AYPC              ","  
228 ","CIFS/SMB"," C Negotiate Protocol Max Dialect Index=7" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 12 arrived at  12:59:02.3854; frame size is 228 (00E4 hex) bytes. 
      DLC:  Destination = Station 001083027B34 
      DLC:  Source      = Station 005054FEEA31 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 214 bytes 
      IP: Identification  = 8193 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = C2D9 (correct) 
      IP: Source address      = [192.168.10.5], AYPC 
      IP: Destination address = [10.48.66.106], RAGE 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 1037 
      TCP: Destination port        = 139 (NetBIOS-ssn) 
      TCP: Sequence number         = 39831 
      TCP: Next expected Seq number= 40005 
      TCP: Acknowledgment number   = 590106 
      TCP: Data offset             = 20 bytes 
      TCP: Flags                   = 18 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...1 .... = Acknowledgment 
      TCP:               .... 1... = Push 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..0. = (No SYN) 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 8276 
      TCP: Checksum                = DE16 (correct) 
      TCP: No TCP options 
      TCP: [174 Bytes of data] 
      TCP: 
NETB: ----- NetBIOS Session protocol ----- 
      NETB: 
      NETB: Type = 00 (Session data) 
      NETB: Flags = 00 
      NETB: Total session packet length = 170 
      NETB: 
SMB: ----- SMB (CIFS) Negotiate Protocol Command header ----- 
      SMB: 
      SMB: SMB Constant 
      SMB: Command            = 72 (Negotiate Protocol) 
      SMB: Reserved           = 0 
      SMB: Flags = 18 
      SMB: 0... .... = Client Command 
      SMB: ..0. .... = No Opportunistic file Locking 
      SMB: ...1 .... = Pathnames are already in canonicalized format 
      SMB: .... 1... = Pathnames should be treated as caseless 
      SMB: .... ..0. = Send.No.Ack can not be used as a response 
      SMB: .... ...0 = Doesn't support Lock&Read, Write&Unlock      SMB: Flags2 = 0003 
      SMB:  0... ....  .... .... = STRING type is ASCIIZ 
      SMB:  .0.. ....  .... .... = DOS style Error code 
      SMB:  ..0. ....  .... .... = No Paging IO 
      SMB:  ...0 ....  .... .... = No DFS support 
      SMB:  .... 0...  .... .... = Client not aware of extended security 
      SMB:  .... ....  .... .0.. = Don't use message authentication 
      SMB:  .... ....  .... ..1. = Client supports extended attributes 
      SMB:  .... ....  .... ...1 = Client supports Long file names 
      SMB: Reserved2(MBZ)     = 000000000000000000000000 
      SMB: Tree ID            = 0000 
      SMB: Process ID         = CAFE 
      SMB: Unauth User ID     = 0000 
      SMB: Multiplex ID       = 0000 
      SMB: 
      SMB: ----- Negotiate Protocol Header ----- 
      SMB: 
      SMB: Word count         = 0 
      SMB: Byte Count         = 135 
      SMB: Byte parameters    = 025043204E4554574F524B2050524F4752414D20312E300
00258454E495820434F524500024D4943524F534F4654204E4554574F524B5320312E303300024C
414E4D414E312E30000257696E646F777320666F7220576F726B67726F75707320332E316100024
C4D312E3258303032... 
      SMB: Offered Dialects: 
      SMB:     0 = PC NETWORK PROGRAM 1.0 
      SMB:     1 = XENIX CORE 
      SMB:     2 = MICROSOFT NETWORKS 1.03 
      SMB:     3 = LANMAN1.0 
      SMB:     4 = Windows for Workgroups 3.1a 
      SMB:     5 = LM1.2X002 
      SMB:     6 = LANMAN2.1 
      SMB:     7 = NT LM 0.12 
      SMB: 

- - - - - - - - - - - - - - - - - - - - Frame 13 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source        
    \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","    13","0.000.286    ","AYPC              ","RAGE              ","  
149 ","CIFS/SMB"," R Negotiate Protocol (to frame 12) Status= OK   Chosen Dialect
 Index=7" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 13 arrived at  12:59:02.3857; frame size is 149 (0095 hex) bytes. 
      DLC:  Destination = Station 005054FEEA31 
      DLC:  Source      = Station 001083027B34 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 135 bytes 
      IP: Identification  = 50914 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = 1C47 (correct) 
      IP: Source address      = [10.48.66.106], RAGE 
      IP: Destination address = [192.168.10.5], AYPC 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 139 (NetBIOS-ssn) 
      TCP: Destination port        = 1037 
      TCP: Sequence number         = 590106 
      TCP: Next expected Seq number= 590201 
      TCP: Acknowledgment number   = 40005 
      TCP: Data offset             = 20 bytes 
      TCP: Flags                   = 18 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...1 .... = Acknowledgment 
      TCP:               .... 1... = Push 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..0. = (No SYN) 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 8034 
      TCP: Checksum                = 1A8D (correct) 
      TCP: No TCP options 
      TCP: [95 Bytes of data] 
      TCP: 
NETB: ----- NetBIOS Session protocol ----- 
      NETB: 
      NETB: Type = 00 (Session data) 
      NETB: Flags = 00 
      NETB: Total session packet length = 91 
      NETB: 
SMB: ----- SMB (CIFS) Negotiate Protocol Response header ----- 
      SMB: 
      SMB: Response to frame 12 
      SMB: SMB Constant 
      SMB: Command            = 72 (Negotiate Protocol) 
      SMB: Error Class        = 0 (Success) 
      SMB: Reserved(MBZ)      = 0 
      SMB: Status             = 0 (OK) 
      SMB: Flags = 98 
      SMB: 1... .... = Server Response 
      SMB: ..0. .... = No Opportunistic file Locking 
      SMB: ...1 .... = Pathnames are already in canonicalized format 
      SMB: .... 1... = Pathnames should be treated as caseless 
      SMB: .... ..0. = Send.No.Ack can not be used as a response 
      SMB: .... ...0 = Doesn't support Lock&Read, Write&Unlock 
      SMB: Flags2 = 0003 
      SMB:  0... ....  .... .... = STRING type is ASCIIZ 
      SMB:  .0.. ....  .... .... = DOS style Error code 
      SMB:  ..0. ....  .... .... = No Paging IO 
      SMB:  ...0 ....  .... .... = No DFS support 
      SMB:  .... 0...  .... .... = Client not aware of extended security 
      SMB:  .... ....  .... .0.. = Don't use message authentication 
      SMB:  .... ....  .... ..1. = Client supports extended attributes 
      SMB:  .... ....  .... ...1 = Client supports Long file names 
      SMB: Reserved2(MBZ)     = 000000000000000000000000 
      SMB: Tree ID            = 0000 
      SMB: Process ID         = CAFE 
      SMB: Unauth User ID     = 0000 
      SMB: Multiplex ID       = 0000 
      SMB: 
      SMB: ----- Negotiate Protocol Header ----- 
      SMB: 
      SMB: Word count         = 17 
      SMB: Parameter words    = 07000332000100041100000000010000000000FD43000070
200231859EC101C4FF08 
      SMB: Byte Count         = 22 
      SMB: Byte parameters    = F8F7053802B9C4435400410043005700450042000000 
      SMB: Selected Dialect index  = 7 
      SMB: Security mode = X3 
      SMB:     .... 0... = Security Signatures not required 
      SMB:     .... .0.. = Does not support Message Authentication protocol 
      SMB:     .... ..1. = Support Challenge response authentication 
      SMB:     .... ...1 = User level security 
      SMB: Max pending mpx requests= 50 
      SMB: Max virtual circuits    = 1 
      SMB: Max Buffer size         = 4356 
      SMB: Max Raw size            = 65536 
      SMB: Session key             = 00000000 
      SMB: Capabilities (LSW) = 43FD 
      SMB:  .1.. ....  .... .... = Supports Large Read&X requests 
      SMB:  ...0 ....  .... .... = Does not support Server DFS 
      SMB:  .... ..1.  .... .... = Supports NT Find 
      SMB:  .... ...1  .... .... = Supports Lock&Read, Write&Unlock 
      SMB:  .... ....  1... .... = Level II oplocks supported 
      SMB:  .... ....  .1.. .... = NT 32-bit status codes recognized 
      SMB:  .... ....  ..1. .... = Remote APIs via RPC supported 
      SMB:  .... ....  ...1 .... = NT 0.12 SMBs supported 
      SMB:  .... ....  .... 1... = Large files and 64 bit file offsets supported 
      SMB:  .... ....  .... .1.. = Unicode strings recognized 
      SMB:  .... ....  .... ..0. = Read/Write Block Multiplexed not supported 
      SMB:  .... ....  .... ...1 = Read/Write Block Raw supported 
      SMB: Capabilities (MSW) = 0000 
      SMB:  0... ....  .... .... = Does not support extended security validation 
      SMB:  .0.. ....  .... .... = Does not support compressed data transfer 
      SMB:  ..0. ....  .... .... = Does not support Bulk Read and Write 
      SMB: Universal Coordinated Time = 16-Jan-02 11:59:03 
      SMB: Minutes from UCT        = 65476 
      SMB: Encryption Key Length   = 8 
      SMB: Byte Count              = 22 
      SMB: Encryption Key          = F8F7053802B9C443 
      SMB: Server's Primary Domain = TACWEB 
      SMB: 

- - - - - - - - - - - - - - - - - - - - Frame 14 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source        
    \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","    14","0.001.963    ","RAGE              ","AYPC              ","  
230 ","CIFS/SMB"," C Tree Connect AndX  Path=\\RAGE\IPC$, Service=IPC" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 14 arrived at  12:59:02.3877; frame size is 230 (00E6 hex) bytes. 
      DLC:  Destination = Station 001083027B34 
      DLC:  Source      = Station 005054FEEA31 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 216 bytes 
      IP: Identification  = 8449 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = C1D7 (correct) 
      IP: Source address      = [192.168.10.5], AYPC 
      IP: Destination address = [10.48.66.106], RAGE 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 1037 
      TCP: Destination port        = 139 (NetBIOS-ssn) 
      TCP: Sequence number         = 40005 
      TCP: Next expected Seq number= 40181 
      TCP: Acknowledgment number   = 590201 
      TCP: Data offset             = 20 bytes 
      TCP: Flags                   = 18 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...1 .... = Acknowledgment 
      TCP:               .... 1... = Push 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..0. = (No SYN) 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 8181 
      TCP: Checksum                = B44C (correct) 
      TCP: No TCP options 
      TCP: [176 Bytes of data] 
      TCP: 
NETB: ----- NetBIOS Session protocol ----- 
      NETB: 
      NETB: Type = 00 (Session data) 
      NETB: Flags = 00 
      NETB: Total session packet length = 172 
      NETB: 
SMB: ----- SMB (CIFS) Setup Account AndX Command header ----- 
      SMB: 
      SMB: SMB Constant 
      SMB: Command            = 73 (Setup Account AndX) 
      SMB: Reserved           = 0 
      SMB: Flags = 18 
      SMB: 0... .... = Client Command 
      SMB: ..0. .... = No Opportunistic file Locking 
      SMB: ...1 .... = Pathnames are already in canonicalized format 
      SMB: .... 1... = Pathnames should be treated as caseless 
      SMB: .... ..0. = Send.No.Ack can not be used as a response 
      SMB: .... ...0 = Doesn't support Lock&Read, Write&Unlock
      SMB: Flags2 = 8003 
      SMB:  1... ....  .... .... = STRING type is UNICODE 
      SMB:  .0.. ....  .... .... = DOS style Error code 
      SMB:  ..0. ....  .... .... = No Paging IO 
      SMB:  ...0 ....  .... .... = No DFS support 
      SMB:  .... 0...  .... .... = Client not aware of extended security 
      SMB:  .... ....  .... .0.. = Don't use message authentication 
      SMB:  .... ....  .... ..1. = Client supports extended attributes 
      SMB:  .... ....  .... ...1 = Client supports Long file names 
      SMB: Reserved2(MBZ)     = 0000A9B9522B700714DC0000 
      SMB: Tree ID            = 0000 
      SMB: Process ID         = CAFE 
      SMB: Unauth User ID     = 0000 
      SMB: Multiplex ID       = 0000 
      SMB: 
      SMB: ----- Setup Account AndX Header ----- 
      SMB: 
      SMB: Word count         = 13 
      SMB: Parameter words    = 75008400041132000100000000000100000000000000D
4000000 
      SMB: Byte Count         = 71 
      SMB: Byte parameters    = 0000000000570069006E0064006F007700730020004E0
054002000310033003800310000000000570069006E0064006F007700730020004E0054002000
34002E00300000000000 
      SMB: AndX command       = 75 (Tree Connect AndX) 
      SMB: AndX reserved(MBZ) = 00 
      SMB: AndX offset        = 0084 
      SMB: Max buffer size         = 4356 
      SMB: Max mux pending requests= 50 
      SMB: Number of VC's (0=0nly) = 1 
      SMB: Session Key             = 00000000 
      SMB: Case insensitive Password length = 1 
      SMB: Case sensitive Password length   = 0 
      SMB: Reserved(MBZ)           = 00000000 
      SMB: Capabilities (LSW) = 00D4 
      SMB:  .0.. ....  .... .... = Does not support Large Read&X requests 
      SMB:  ...0 ....  .... .... = Does not support Server DFS 
      SMB:  .... ..0.  .... .... = Does not support NT Find 
      SMB:  .... ...0  .... .... = Does not support Lock&Read, Write&Unlock
      SMB:  .... ....  1... .... = Level II oplocks supported 
      SMB:  .... ....  .1.. .... = NT 32-bit status codes recognized 
      SMB:  .... ....  ..0. .... = Remote APIs via RPC not supported 
      SMB:  .... ....  ...1 .... = NT 0.12 SMBs supported 
      SMB:  .... ....  .... 0... = Large files not supported 
      SMB:  .... ....  .... .1.. = Unicode strings recognized 
      SMB:  .... ....  .... ..0. = Read/Write Block Multiplexed not supported 
      SMB:  .... ....  .... ...0 = Read/Write Block Raw not supported 
      SMB: Capabilities (MSW) = 0000 
      SMB:  0... ....  .... .... = Does not support extended security validation 
      SMB:  .0.. ....  .... .... = Does not support compressed data transfer 
      SMB:  ..0. ....  .... .... = Does not support Bulk Read and Write 
      SMB: Byte Count              = 71 
      SMB: Case insensitive password = 00 
      SMB: Account name            = 
      SMB: Client's Primary Domain = 
      SMB: Client's native OS      = Windows NT 1381 
      SMB: CIFS 1.1 spec violation = 0 
      SMB: Client's LANMAN         = Windows NT 4.0 
      SMB: 
      SMB: ----- Tree Connect AndX Header ----- 
      SMB: 
      SMB: Word count         = 4 
      SMB: Parameter words    = FF00000000000100 
      SMB: Byte Count         = 29 
      SMB: Byte parameters    = 005C005C0052004100470045005C0049005000430024000
00049504300 
      SMB: AndX command       = FF (End of chain) 
      SMB: AndX reserved(MBZ) = 00 
      SMB: AndX offset        = 0000 
      SMB: Additional information = 0000 
      SMB:   .... ....  .... ...0 = Don't disconnect Tid 
      SMB: Password length         = 1 
      SMB: Byte Count              = 29 
      SMB: Password                = 00 
      SMB: Path                    = \\RAGE\IPC$ 
      SMB: Service                 = IPC 
      SMB: 

- - - - - - - - - - - - - - - - - - - - Frame 15 - - - - - - - - - - - - - - - - - - - - 
\"Flags \",\"Frame \",\"Delta Time   \",\"Destination       \",\"Source       
     \",\"Bytes\",\"Protocol  \",\"Summary\" 
"      ","    15","0.000.406    ","AYPC              ","RAGE              "," 
 198 ","CIFS/SMB"," R Tree Connect AndX  Service=IPC ,Native File System=" 
DLC:  ----- DLC Header ----- 
      DLC: 
      DLC:  Frame 15 arrived at  12:59:02.3881; frame size is 198 (00C6 hex) bytes. 
      DLC:  Destination = Station 005054FEEA31 
      DLC:  Source      = Station 001083027B34 
      DLC:  Ethertype   = 0800 (IP) 
      DLC: 
IP: ----- IP Header ----- 
      IP: 
      IP: Version = 4, header length = 20 bytes 
      IP: Type of service = 00 
      IP:       000. ....   = routine 
      IP:       ...0 .... = normal delay 
      IP:       .... 0... = normal throughput 
      IP:       .... .0.. = normal reliability 
      IP:       .... ..0. = ECT bit - transport protocol will ignore the CE bit 
      IP:       .... ...0 = CE bit - no congestion 
      IP: Total length    = 184 bytes 
      IP: Identification  = 51170 
      IP: Flags           = 4X 
      IP:       .1.. .... = don't fragment 
      IP:       ..0. .... = last fragment 
      IP: Fragment offset = 0 bytes 
      IP: Time to live    = 128 seconds/hops 
      IP: Protocol        = 6 (TCP) 
      IP: Header checksum = 1B16 (correct) 
      IP: Source address      = [10.48.66.106], RAGE 
      IP: Destination address = [192.168.10.5], AYPC 
      IP: No options 
      IP: 
TCP: ----- TCP header ----- 
      TCP: 
      TCP: Source port             = 139 (NetBIOS-ssn) 
      TCP: Destination port        = 1037 
      TCP: Sequence number         = 590201 
      TCP: Next expected Seq number= 590345 
      TCP: Acknowledgment number   = 40181 
      TCP: Data offset             = 20 bytes 
      TCP: Flags                   = 18 
      TCP:               ..0. .... = (No urgent pointer) 
      TCP:               ...1 .... = Acknowledgment 
      TCP:               .... 1... = Push 
      TCP:               .... .0.. = (No reset) 
      TCP:               .... ..0. = (No SYN) 
      TCP:               .... ...0 = (No FIN) 
      TCP: Window                  = 7858 
      TCP: Checksum                = F7E6 (correct) 
      TCP: No TCP options 
      TCP: [144 Bytes of data] 
      TCP: 
NETB: ----- NetBIOS Session protocol ----- 
      NETB: 
      NETB: Type = 00 (Session data) 
      NETB: Flags = 00 
      NETB: Total session packet length = 140 
      NETB: 
SMB: ----- SMB (CIFS) Setup Account AndX Response header ----- 
      SMB: 
      SMB: Response to frame 14 
      SMB: SMB Constant 
      SMB: Command            = 73 (Setup Account AndX) 
      SMB: Error Class        = 0 (Success) 
      SMB: Reserved(MBZ)      = 0 
      SMB: Status             = 0 (OK) 
      SMB: Flags = 98 
      SMB: 1... .... = Server Response 
      SMB: ..0. .... = No Opportunistic file Locking 
      SMB: ...1 .... = Pathnames are already in canonicalized format 
      SMB: .... 1... = Pathnames should be treated as caseless 
      SMB: .... ..0. = Send.No.Ack can not be used as a response 
      SMB: .... ...0 = Doesn't support Lock&Read, Write&Unlock
      SMB: Flags2 = 8003 
      SMB:  1... ....  .... .... = STRING type is UNICODE 
      SMB:  .0.. ....  .... .... = DOS style Error code 
      SMB:  ..0. ....  .... .... = No Paging IO 
      SMB:  ...0 ....  .... .... = No DFS support 
      SMB:  .... 0...  .... .... = Client not aware of extended security 
      SMB:  .... ....  .... .0.. = Don't use message authentication 
      SMB:  .... ....  .... ..1. = Client supports extended attributes 
      SMB:  .... ....  .... ...1 = Client supports Long file names 
      SMB: Reserved2(MBZ)     = 0000A9B9522B700714DC0000 
      SMB: Tree ID            = 0801 
      SMB: Process ID         = CAFE 
      SMB: Unauth User ID     = 0801 
      SMB: Multiplex ID       = 0000 
      SMB: 
      SMB: ----- Setup Account AndX Header ----- 
      SMB: 
      SMB: Word count         = 3 
      SMB: Parameter words    = 75007C000000 
      SMB: Byte Count         = 83 
      SMB: Byte parameters    = 00570069006E0064006F007700730020004E005400200
034002E00300000004E00540020004C0041004E0020004D0061006E0061006700650072002000
34002E00300000005400410043005700450042000000 
      SMB: AndX command       = 75 (Tree Connect AndX) 
      SMB: AndX reserved(MBZ) = 00 
      SMB: AndX offset        = 007C 
      SMB: Request Mode = 0000 
      SMB:  .... ....  .... ...0 = Not logged in as 'Guest' 
      SMB: Byte Count              = 83 
      SMB: Server's Native OS      = Windows NT 4.0 
      SMB: Server's Native LAN Man = NT LAN Manager 4.0 
      SMB: Server's Primary Domain = TACWEB 
      SMB: 
      SMB: ----- Tree Connect AndX Header ----- 
      SMB: 
      SMB: Word count         = 3 
      SMB: Parameter words    = FF008C000100 
      SMB: Byte Count         = 7 
      SMB: Byte parameters    = 49504300000000 
      SMB: AndX command       = FF (End of chain) 
      SMB: AndX reserved(MBZ) = 00 
      SMB: AndX offset        = 008C 
      SMB: Optional support = 0001 
      SMB:  .... ....  .... ..0. = Share not in DFS 
      SMB:  .... ....  .... ...1 = Support Search bits 
      SMB: Byte Count              = 7 
      SMB: Service                 = IPC 
      SMB: Native File system      = 
      SMB:

Información Relacionada


Document ID: 18801