WAN : Protocolo punto a punto (PPP)

Uso de Puente medio PPP para conectar redes enrutadas y con conexión en puente.

18 Octubre 2015 - Traducción Automática
Otras Versiones: PDFpdf | Inglés (22 Agosto 2015) | Comentarios


Contenido


Introducción

Este documento proporciona una configuración de muestra para usar el mitad-bridging PPP para conectar ruteado y los Bridged Network.

prerrequisitos

Requisitos

No hay requisitos específicos para este documento.

Componentes Utilizados

La información que contiene este documento se basa en las siguientes versiones de software y hardware.

  • Software Release 12.2(7b) de Cisco IOS�.

  • Dos Cisco 2500 Series Router. Cada uno tiene por lo menos una interfaz del ISDN BRI.

La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener cualquier comando.

Productos Relacionados

Esta configuración también se puede utilizar con las siguientes versiones de hardware y software:

  • Cualquier interfaz serial, tal como serial, Basic Rate Interface (BRI), interfaz de la velocidad primaria (PRI), y así sucesivamente.

  • Cisco IOS Software Release 11.2.

  • Cualquier Cisco IOS Software corriente del router como se mencionó anteriormente, y por lo menos un puerto ISDN-BRI. Sin embargo, la función half-bridge se puede utilizar en un router con una interfaz serial.

Convenciones

Para obtener más información sobre las convenciones del documento, consulte Convenciones de Consejos Técnicos de Cisco.

Antecedentes

El puente envía paquetes de puente al medio puente PPP que los convierte en paquetes enrutados y los reenvía a otros procesos del router. Asimismo, el semipuente PPP convierte los paquetes ruteados a los paquetes del Bridge de Ethernet, y los envía al Bridge en la misma subred Ethernet.

Nota: Esta configuración no cubre un Bridge completo en los ambos lados. Para tal configuración refiera al documento del Bridging Across ISDN.

Sea consciente que el interligar en una conexión ISDN tiende a mantener la conexión activa por mismo los períodos prolongados, si no permanentemente. Si la compañía telefónica carga para el ISDN basado el tiempo de conexión, ésta puede dar lugar a una cuenta muy grande. Por lo tanto, este escenario se recomienda para los que tengan líneas ISDN de uso ilimitado.

Nota: Una interfaz no puede funcionar como un semipuente y un Bridge. El Cisco IOS Software soporta no más que un semipuente PPP por la subred Ethernet.

Configurar

En esta sección encontrará la información para configurar las funciones descritas en este documento.

Nota: Para obtener información adicional sobre los comandos que se utilizan en este documento, use la Command Lookup Tool (solo para clientes registrados).

Diagrama de la red

En este documento, se utiliza esta configuración de red:

/image/gif/paws/10381/ppp_half_bridging.gif

Configuraciones

En este documento, se utilizan estas configuraciones:

  • Venus

    Configuran a este router como Bridge completo con el Routing IP inhabilitado. Los diales del dispositivo cuando llega cualquier tráfico Bridged.

  • Saturn

    Han configurado a este router como Half-Bridge. Observe que no configuran a los comandos dialer string, dialer group, y dialer list en este lado. Este router nunca marcará tan, pero validará las llamadas entrantes. Esto evita que el router marque el router remoto. Hemos girado el Routing IP aquí. El Bridging Software lleno no se configura en este router. El Half-Bridge PPP se está ejecutando en la interfaz BRI, así que los comandos como la demostración interligan y el atravesar-árbol de la demostración no rinde ninguna salida en este router.

Venus
Venus#show running-config
!
version 12.2
!
hostname Venus
!
username Saturn password 0 same 

!--- Required for PPP CHAP authentication during dialup

ip subnet-zero
no ip routing 

!--- Turn off routing

no ip domain-lookup
!
isdn switch-type basic-5ess

!--- The ISDN switchtype for this circuit. Obtain this information from the 
!--- Telco. This ISDN switch type is USA specific and could be changed          
!--- depending on the country and TELCO requirements

!
interface Ethernet0
ip address 10.1.1.2 255.0.0.0 

!--- This is for management purpose only

no ip route-cache
no ip mroute-cache
bridge-group 1

!--- Assign this interface to Bridge Group 1
!--- Frames are bridged only among interfaces in the same group
!--- Note: the dialer1 interface is also in this bridge-group 1

interface BRI0
no ip address
no ip route-cache
no ip mroute-cache
dialer pool-member 1  

!--- Dialer profiles configured with same dialer pool #
!--- (in this case, dialer1) will bind to this interface

isdn switch-type basic-5ess

!--- Check with your Telco for the correct values

!
interface Dialer1 

!--- Configure the Dialer profile

description ISDN to Saturn
ip address 10.1.1.2 255.0.0.0
encapsulation ppp
dialer pool 1

!--- Use physical interfaces configured with same pool # 
!--- (in this case, bri0) during dialup

dialer remote-name Saturn 

!--- Specifies remote CHAP name

dialer string 5552000 

!--- Specifies the number to dial when interesting traffic arrives

dialer-group 1 

!--- Defines the interesting traffic as configured in the dialer-list

ppp authentication chap 

!--- Use CHAP as the authentication method

bridge-group 1 

!--- Assign this interface to Bridge Group 1.
!--- Frames are bridged only among interfaces in the same group.
!--- Note: the Ethernet interface 0 is also in this bridge-group 1


ip default-gateway 10.1.1.3      

!--- All default traffic from Venus should go through Saturn

dialer-list 1 protocol bridge permit 

!--- Defines the interesting traffic. In this case, all bridged traffic

bridge 1 protocol ieee

!--- Define the type of Spanning-Tree Protocol used for the interface in
!--- bridge-group 1. Here we use the IEEE spanning tree protocol. The IEEE 802.1D
!--- Spanning-Tree Protocol is the preferred way of running the bridge.

!

Saturn
Saturn#show running-config
!
version 12.2
!
hostname Saturn
!
username Venus password 0 same 

!--- Required for PPP CHAP authentication during dialup

ip subnet-zero
no ip domain-lookup
!
isdn switch-type basic-5ess

!--- The ISDN switchtype for this circuit. Obtain this information from the 
!--- Telco. This ISDN switch type is USA specific and could be changed          
!--- depending on the country and Telco requirements

!
interface Ethernet0
ip address 192.168.1.1 255.255.0.0
!
interface BRI0
no ip address
no ip mroute-cache
dialer pool-member 1

!--- Dialer profiles configured with same dialer pool #
!--- (in this case, dialer1) will bind to this interface

isdn switch-type basic-5ess
!
interface Dialer1 

!--- Configure the Dialer profile

description ISDN to Venus
ip address 10.1.1.3 255.0.0.0 

!--- IP address is required to route the bridged traffic from Venus
!--- This ip address MUST be in the same subnet as the remote bridge network

encapsulation ppp 
dialer pool 1

!--- Use physical interfaces configured with same pool # 
!--- (in this case, bri0) during dialup

dialer remote-name Venus
pulse-time 0
ppp bridge ip 

!--- Configures half bridge 

ppp authentication chap                                                          

!--- Use CHAP as the authentication method

!

Verificación

En esta sección encontrará información que puede utilizar para confirmar que su configuración esté funcionando correctamente.

La herramienta Output Interpreter (sólo para clientes registrados) permite utilizar algunos comandos “show” y ver un análisis del resultado de estos comandos.

  • isdn status de la demostración — visualiza el estatus L1, L2, y L3 de las interfaces de ISDN.

  • marcador de la demostración — visualiza el estatus del marcador, y el estado individual de los canales ISDN.

  • Bridge de la demostración — clases de las visualizaciones de entradas en el Bridge Forwarding Database, en el modo EXEC privilegiado.

  • interfaz de la demostración — visualiza el estatus de las diversas interfaces, incluyendo el serial y las interfaces BRI.

  • la demostración arp — marca la asignación ARP. El ARP es un protocolo usado para asociar el direccionamiento de la capa 2 (dirección MAC) a un direccionamiento de la capa 3 (dirección IP).

  • atravesar-árbol de la demostración — visualiza la topología del árbol de expansión sabida al router.

Comandos show en Venus luego realizar la llamada a Saturno

Venus#show isdn status
Global ISDN Switchtype = basic-5ess
ISDN BRI0 interface
        dsl 0, interface ISDN Switchtype = basic-5ess
    Layer 1 Status:
        ACTIVE
    Layer 2 Status:
        TEI = 107, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
        1 Active Layer 3 Call(s)
        CCB:callid=800E, sapi=0, ces=1, B-chan=2, calltype=DATA    
Active dsl 0 CCBs = 1
    The Free Channel Mask:
  0x80000001
    Number of L2 Discards = 0, L2 Session ID = 17
    Total Allocated ISDN CCBs = 1
Venus#show dialer
BRI0 - dialer type = ISDN

Dial String Successes Failures Last DNIS Last status
   0 incoming call(s) have been screened.
   0 incoming call(s) rejected for callback.

BRI0:1 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is idle

BRI0:2 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up
   Dial reason: bridge (0x0800)
   Interface bound to profile Di1
   Time until disconnect 90 secs
   Current call connected 00:00:31

Di1 - dialer type = DIALER PROFILE
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up
   Number of active calls = 1
   Dial String Successes Failures Last DNIS	 Last status
   5552000   5   1   00:00:34  Successful Default

Venus#show interface bri0:2
   BRI0:2 is up, line protocol is up
   Hardware is BRI
   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   Keepalive set (10 sec)
   Time to interface disconnect: idle 00:01:18
   Interface is bound to Di1 (Encapsulation PPP)
   LCP Open
   Closed: IPCP
   Open: BRIDGECP, CDPCP                     
   
!--- Bridge Control Protocol is open

   Last input 00:00:42, output 00:00:00, output hang never
   Last clearing of "show interface" counters never
   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
   Queueing strategy: fifo
   Output queue :0/40 (size/max)
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
   161 packets input, 9796 bytes, 0 no buffer
   Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
   0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
   328 packets output, 16659 bytes, 0 underruns
   0 output errors, 0 collisions, 7 interface resets
   0 output buffer failures, 0 output buffers swapped out
   16 carrier transitions
Venus#show bridge
Total of 300 station blocks, 298 free
   Codes: P - permanent, S - self

Bridge Group 1:

 Address Action Interface Age RX count TX count
   00d0.58ad.ae13 forward Ethernet0 0 74 58
   0060.5cf4.a955 forward Dialer1 0 58 72

Venus#show arp
   Protocol Address Age (min) Hardware Addr Type Interface
   Internet 10.1.1.2 - 0060.5cf4.a9a8 ARPA Ethernet0
   Internet 10.1.1.3 0 0060.5cf4.a955 ARPA Dialer1

Venus#show spanning-tree
 
Bridge group 1 is executing the ieee compatible Spanning Tree protocol
   Bridge Identifier has priority 32768, address 0060.5cf4.a9a8
   Configured hello time 2, max age 20, forward delay 15
   Current root has priority 32768, address 0009.7c2e.ba00
   Root port is 2 (Ethernet0), cost of root path is 100
   Topology change flag not set, detected flag not set
   Number of topology changes 1 last change occurred 22:09:28 ago
   from Ethernet0
   Times: hold 1, topology change 35, notification 2
   hello 2, max age 20, forward delay 15
   Timers: hello 0, topology change 0, notification 0, aging 300
 
Port 2 (Ethernet0) of Bridge group 1 is forwarding
   Port path cost 100, Port priority 128, Port Identifier 128.2.
   Designated root has priority 32768, address 0009.7c2e.ba00
   Designated bridge has priority 32768, address 0009.7c2e.ba00
   Designated port id is 128.13, designated path cost 0
   Timers: message age 2, forward delay 0, hold 0
   Number of transitions to forwarding state: 1
   BPDU: sent 1, received 39911

 Port 8 (Dialer1) of Bridge group 1 is forwarding
   Port path cost 17857, Port priority 128, Port Identifier 128.8.
   Designated root has priority 32768, address 0009.7c2e.ba00
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.8, designated path cost 100
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 1
   BPDU: sent 39879, received 0

Comandos show en Saturno luego de que Venus realiza la llamada

Saturn#show dialer
BRI0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
   0 incoming call(s) have been screened.

   0 incoming call(s) rejected for callback.

BRI0:1 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is idle

BRI0:2 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up
   Interface bound to profile Di1
   Time until disconnect 45 secs
   Connected to <unknown phone number> (Venus)

Di1 - dialer type = DIALER PROFILE
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up   Number of active calls = 1

Dial String Successes Failures Last DNIS Last status

Saturn#show isdn status
   Global ISDN Switchtype = basic-5ess
   ISDN BRI0 interface
   dsl 0, interface ISDN Switchtype = basic-5ess
   Layer 1 Status:
   ACTIVE
   Layer 2 Status:
   TEI = 105, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
   I_Queue_Len 0, UI_Queue_Len 0
   Layer 3 Status:
   1 Active Layer 3 Call(s)
   CCB:callid=2B, sapi=0, ces=1, B-chan=2, calltype=DATA
   Active dsl 0 CCBs = 1
   The Free Channel Mask: 0x80000001
   Number of L2 Discards = 0, L2 Session ID = 37
   Total Allocated ISDN CCBs = 1

Saturn#show arp
   Protocol Address Age (min) Hardware Addr Type Interface
   Internet 10.1.1.2 27 0060.5cf4.a9a8 ARPA Dialer1
   Internet 10.1.1.1 63 00d0.58ad.ae13 ARPA Dialer1
   Internet 192.168.1.1 - 0060.5cf4.a955 ARPA Ethernet0
   Internet 192.168.1.2 53 0000.0c76.2882 ARPA Ethernet0

Saturn#show spanning-tree
No spanning tree instances exist. 

!--- This router does not run full bridge, 
!--- so spanning tree does not run on this router


Saturn#show ip route
   Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
   D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
   N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
   E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
   i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
   * - candidate default, U - per-user static route, o - ODR
   P - periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, Dialer1 
C 192.168.0.0/16 is directly connected, Ethernet0

Troubleshooting

En esta sección encontrará información que puede utilizar para solucionar problemas de configuración.

Recursos de resolución de problemas

Los procedimientos deTroubleshooting para las llamadas ISDN entrantes y salientes se explican en la tecnología de marcación manual: Documento de las técnicas de Troubleshooting. La información adicional en cómo resolver problemas los problemas de la capa ISDN 1, de la capa 2 y de la capa 3 se da al usar el comando show isdn status para el Troubleshooting de BRI y las localizaciones de averías del ISDN BRI acodan 3 usando el comando debug isdn q931.

Comandos para resolución de problemas

La herramienta Output Interpreter (sólo para clientes registrados) permite utilizar algunos comandos “show” y ver un análisis del resultado de estos comandos.

Nota: Antes de ejecutar un comando de depuración, consulte Información importante sobre comandos de depuración.

  • debug dialer — indica cuando se ha detectado el tráfico interesante, y cuando se inicia la marca.

  • debug isdn event — indica la actividad ISDN que ocurre en el lado del usuario de la interfaz de ISDN, y es similar hacer el debug de ISDN q931.

  • debug ISDN q931 — proporciona la información sobre la configuración de la llamada y cierre de las conexiones de red ISDN (capa 3), entre el router local (lado del usuario) y la red.

  • el debug isdn q921 — visualiza la capa del link de datos (los procedimientos de acceso de la capa 2) que están ocurriendo en el router en el canal D (LAPD) de su interfaz de ISDN.

  • negociación ppp del debug — realiza la negociación de opciones PPP y los parámetros del protocolo network control (NCP).

  • autenticación PPP del debug — permite el intercambio de los paquetes del protocolo challenge authentication (GRIETA) y del protocolo password authentication (PAP).

Comandos Debug en el Venus cuando llega el tráfico interesante

Venus#
*Mar  1 22:00:14.838: BR0 DDR: rotor dialout [priority]
*Mar  1 22:00:14.838: BR0 DDR: Dialing cause bridge (0x0800)
*Mar  1 22:00:14.842: BR0 DDR: Attempting to dial 5552000
*Mar  1 22:00:14.846: ISDN BR0: Outgoing call id = 0x8006, dsl 0
*Mar  1 22:00:14.846: ISDN BR0: Event: Call to 5552000 at 64 Kb/s
*Mar  1 22:00:14.850: ISDN BR0: process_bri_call(): call id 0x8006, 
called_number 5552000, speed 64, call type DATA
*Mar  1 22:00:14.854: CCBRI_Go Fr Host InPkgInfo (Len=22) :
*Mar  1 22:00:14.858: 1 0 1 80 6 0 4 2 88 90 18 1 83 2C 7 35 35 35 32 30 30 30
*Mar  1 22:00:14.866:
*Mar  1 22:00:14.870: CC_CHAN_GetIdleChanbri: dsl 0
*Mar  1 22:00:14.870:     Found idle channel B1
*Mar  1 22:00:14.886: ISDN BR0: TX -> INFOc sapi=0 tei=106 ns=0 nr=0 
i=0x08010605040288901801832C0735353532303030
*Mar  1 22:00:14.906:     SETUP pd = 8  callref = 0x06
*Mar  1 22:00:14.914:         Bearer Capability i = 0x8890
*Mar  1 22:00:14.918:         Channel ID i = 0x83
*Mar  1 22:00:14.92Venus#6:         Keypad Facility i = '5552000'
*Mar  1 22:00:15.190: ISDN BR0: RX <- INFOc sapi=0 tei=106 ns=0 nr=1 
i=0x0801860218018A
*Mar  1 22:00:15.198:     CALL_PROC pd = 8  callref = 0x86
*Mar  1 22:00:15.206:         Channel ID i = 0x8A
*Mar  1 22:00:15.222: ISDN BR0: TX -> RRr sapi=0 tei=106 nr=1
*Mar  1 22:00:15.230: CCBRI_Go Fr L3 pkt (Len=7) :
*Mar  1 22:00:15.230: 2 1 6 98 18 1 8A
*Mar  1 22:00:15.234:
*Mar  1 22:00:15.238: ISDN BR0: LIF_EVENT: ces/callid 1/0x8006 
HOST_PROCEEDING
*Mar  1 22:00:15.238: ISDN BR0: HOST_PROCEEDING
*Mar  1 22:00:15.242: ISDN BR0: HOST_MORE_INFO
*Mar  1 22:00:15.658: ISDN BR0: RX <- INFOc sapi=0 tei=106 ns=1 
nr=1 i=0x08018607
*Mar  1 22:00:15.666:     CONNECT pd = 8  callref = 0x86
*Mar  1 22:00:15.678: ISDN BR0: TX -> RRr sapi=0 tei=106 nr=2
*Mar  1 22:00:15.686: CCBRI_Go Fr L3 pkt (Len=4) :
*Mar  1 22:00:15.690: 7 1 6 91
*Mar  1 22:00:15.690:
*Mar  1 22:00:15.694: ISDN BR0: LIF_EVENT: ces/callid 1/0x8006 HOST_CONNECT
22:00:15: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
*Mar  1 22:00:15.702: BR0:2 PPP: Phase is DOWN, Setup [0 sess, 0 load]
*Mar  1 22:00:15.706: BR0:2 PPP: No remote authentication for call-out
*Mar  1 22:00:15.710: BR0:2 PPP: Phase is ESTABLISHING [0 sess, 0 load]
*Mar  1 22:00:15.710: BR0:2 PPP: Treating connection as a callout
*Mar  1 22:00:15.714: BR0:2 PPP: No remote authentication for call-out
*Mar  1 22:00:15.718: BR0:2 LCP: O CONFREQ [Closed] id 1 len 10
*Mar  1 22:00:15.722: BR0:2 LCP:    MagicNumber 0x6515B12A (0x05066515B12A)
*Mar  1 22:00:15.722: BR0:2: interface must be fifo queue, force fifo
22:00:15: %DIALER-6-BIND: Interface BR0:2 bound to profile Di1
*Mar  1 22:00:15.742: ISDN: get_isdn_service_state(): idb 0x1A2DBC bchan 3 
is_isdn 1 Not a Pri
*Mar  1 22:00:15.746: BR0:2 PPP: Treating connection as a callout
*Mar  1 22:00:15.746: ISDN BR0: Event: Connected to 5552000 on B2 at 64 Kb/s
*Mar  1 22:00:15.762: ISDN BR0: TX -> INFOc sapi=0 tei=106 ns=1 nr=2 i=0x0801060F
*Mar  1 22:00:15.766:     CONNECT_ACK pd = 8  callref = 0x06
*Mar  1 22:00:15.774: BR0:2 LCP: I CONFREQ [REQsent] id 1 len 15
*Mar  1 22:00:15.778: BR0:2 LCP:    AuthProto CHAP (0x0305C22305)
*Mar  1 22:00:15.782: BR0:2 LCP:    MagicNumber 0x788C6F8F (0x0506788C6F8F)
*Mar  1 22:00:15.786: BR0:2 LCP: O CONFACK [REQsent] id 1 len 15
*Mar  1 22:00:15.790: BR0:2 LCP:    AuthProto CHAP (0x0305C22305)
*Mar  1 22:00:15.790: BR0:2 LCP:    MagicNumber 0x788C6F8F (0x0506788C6F8F)
*Mar  1 22:00:15.798: BR0:2 LCP: I CONFACK [ACKsent] id 1 len 10
*Mar  1 22:00:15.798: BR0:2 LCP:    MagicNumber 0x6515B12A (0x05066515B12A)
*Mar  1 22:00:15.802: BR0:2 LCP: State is Open
*Mar  1 22:00:15.806: BR0:2 PPP: Phase is AUTHENTICATING, by the peer 
[0 sess, 1 load]
*Mar  1 22:00:15.870: ISDN BR0: RX <- RRr sapi=0 tei=106 nr=2
*Mar  1 22:00:15.882: BR0:2 CHAP: I CHALLENGE id 31 len 27 from "Saturn"
*Mar  1 22:00:15.890: BR0:2 CHAP: O RESPONSE id 31 len 26 from "Venus"
*Mar  1 22:00:15.914: BR0:2 CHAP: I SUCCESS id 31 len 4
*Mar  1 22:00:15.918: BR0:2 PPP: Phase is UP [0 sess, 1 load]
*Mar  1 22:00:15.922: BR0:2 BNCP: O CONFREQ [Closed] id 1 len 4
*Mar  1 22:00:15.926: BR0:2 IPCP: O CONFREQ [Closed] id 1 len 10
*Mar  1 22:00:15.930: BR0:2 IPCP:    Address 10.1.1.2 (0x03060A010102)
*Mar  1 22:00:15.934: BR0:2 CDPCP: O CONFREQ [Closed] id 1 len 4
*Mar  1 22:00:15.942: BR0:2 BNCP: I CONFREQ [REQsent] id 1 len 4
*Mar  1 22:00:15.946: BR0:2 BNCP: O CONFACK [REQsent] id 1 len 4
*Mar  1 22:00:15.950: BR0:2 CDPCP: I CONFREQ [REQsent] id 1 len 4
*Mar  1 22:00:15.954: BR0:2 CDPCP: O CONFACK [REQsent] id 1 len 4
*Mar  1 22:00:15.958: BR0:2 BNCP: I CONFACK [ACKsent] id 1 len 4
*Mar  1 22:00:15.958: BR0:2 BNCP: State is Open
*Mar  1 22:00:15.966: BR0:2 LCP: I PROTREJ [Open] id 2 len 16 protocol IPCP 
(0x80210101000A03060A010102)
*Mar  1 22:00:15.970: BR0:2 IPCP: State is Closed
*Mar  1 22:00:15.974: BR0:2 CDPCP: I CONFACK [ACKsent] id 1 len 4
*Mar  1 22:00:15.978: BR0:2 CDPCP: State is Open
*Mar  1 22:00:15.978: BR0:2 DDR: dialer protocol up
22:00:16: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, 
changed state to up
22:00:21: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 5552000
Venus#
Saturn#
4d16h: ISDN BR0: RX <- UI c/r=1 sapi=0 tei=127 
i=0x080141050402889018018A7008C135353532303030
4d16h:     SETUP pd = 8  callref = 0x41
4d16h:         Bearer Capability i = 0x8890
4d16h:         Channel ID i = 0x8A
4d16h:         Called Party Number i = 0xC1, '5552000', Plan:ISDN, 
Type:Subscriber(local)
4d16h: CCBRI_Go Fr L3 pkt (Len=21) :
4d16h: 5 1 C1 90 4 2 88 90 18 1 8A 70 8 C1 35 35 35 32 30 30 30
4d16h:
4d16h: ISDN BR0: Incoming call id = 0x002B, dsl 0
4d16h: ISDN BR0: LIF_EVENT: ces/callid 1/0x2B HOST_INCOMING_CALL
4d16h: ISDN BR0: HOST_INCOMING_CALL: (non-POTS) DATA
4d16h: ISDN BR0: HOST_INCOMING_CALL: (1) call_type = DATA
4d16h: ISDN BR0: HOST_INCOMING_CALL: voice_answer_data = FALSE call type is DATA
4d16h: ISDN BR0: Event: Received a DATA call from <unknown> on B2 at 64 Kb/s
4d16h: ISDN BR0: Event: Accepting the call id 0x2B
4d16h: BR0:2 PPP: Phase is DOWN, Setup [0 sess, 1 load]
4d16h: BR0:2 PPP: Phase is ESTABLISHING [0 sess, 1 load]
4d16h: BR0:2: inteSarface must be fifo queue, force fifo
4d16h: %DIALER-6-BIND: Interface BR0:2 bound to profile Di1
4d16h: ISDN BR0: RM returned call_type 0 resource type 0 response 1
4d16h: CCBRI_Go Fr Host InPkgInfo (Len=9) :
4d16h: 7 0 1 0 2B 3 18 1 8A
4d16h:
4d16h: ISDN BR0: isdn_send_connect(): msg 4, call id 0x2B, ces 1 bchan 1, c
all type DATA
4d16h: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
4d16h: ISDN: get_isdn_service_state(): idb 0x1A2EAC bchan 3 is_isdn 1 Not a Pri
4d16h: BR0:2 PPP: Treating connection as a callin
4d16h: BR0:2 LCP: State is Listen
4d16h: CCBRI_Go Fr Host InPkgInfo (Len=6) :
4d16h: 4 0 1 0 2B 0
4d16h:
4d16h: ISDN BR0: TX -> INFOc sapi=0 tei=105 ns=7 nr=5 i=0x0801C10218018A
4d16h:     CALL_PROC pd = 8  callref = 0xC1
4d16h:         Channel ID i = 0x8A
4d16h: ISDN BR0: RX <- RRr sapi=0 tei=105 nr=8
4d16h: ISDN BR0: TX -> INFOc sapi=0 tei=105 ns=8 nr=5 i=0x0801C107
4d16h:     CONNECT pd = 8  callref = 0xC1
4d16h: ISDN BR0: RX <- INFOc sapi=0 tei=105 ns=5 nr=9 i=0x0801410F
4d16h:     CONNECT_ACK pd = 8  callref = 0x41
4d16h: ISDN BR0: TX -> RRr sapi=0 tei=105 nr=6
4d16h: CCBRI_Go Fr L3 pkt (Len=4) :
4d16h: F 1 C1 92
4d16h:
4d16h: ISDN BR0: LIF_EVENT: ces/callid 1/0x2B HOST_CONNECT
4d16h: ISDN BR0: Event: Connected to <unknown> on B2 at 64 Kb/s
4d16h: BR0:2 LCP: I CONFREQ [Listen] id 1 len 10
4d16h: BR0:2 LCP:    MagicNumber 0x6515B12A (0x05066515B12A)
4d16h: BR0:2 LCP: O CONFREQ [Listen] id 1 len 15
4d16h: BR0:2 LCP:    AuthProto CHAP (0x0305C22305)
4d16h: BR0:2 LCP:    MagicNumber 0x788C6F8F (0x0506788C6F8F)
4d16h: BR0:2 LCP: O CONFACK [Listen] id 1 len 10
4d16h: BR0:2 LCP:    MagicNumber 0x6515B12A (0x05066515B12A)
4d16h: BR0:2 LCP: I CONFACK [ACKsent] id 1 len 15
4d16h: BR0:2 LCP:    AuthProto CHAP (0x0305C22305)
4d16h: BR0:2 LCP:    MagicNumber 0x788C6F8F (0x0506788C6F8F)
4d16h: BR0:2 LCP: State is Open
4d16h: BR0:2 PPP: Phase is AUTHENTICATING, by this end [0 sess, 0 load]
4d16h: BR0:2 CHAP: O CHALLENGE id 31 len 27 from "Saturn"
4d16h: BR0:2 CHAP: I RESPONSE id 31 len 26 from "Venus"
4d16h: BR0:2 CHAP: O SUCCESS id 31 len 4
4d16h: BR0:2 PPP: Phase is UP [0 sess, 0 load]
4d16h: BR0:2 BNCP: O CONFREQ [Closed] id 1 len 4
4d16h: BR0:2 CDPCP: O CONFREQ [Closed] id 1 len 4
4d16h: BR0:2 BNCP: I CONFREQ [REQsent] id 1 len 4
4d16h: BR0:2 BNCP: O CONFACK [REQsent] id 1 len 4: BR0:2 IPCP: I CONFREQ 
[Not negotiated] id 1 len 10
4d16h: BR0:2 IPCP:    Address 10.1.1.2 (0x03060A010102)
4d16h: BR0:2 LCP: O PROTREJ [Open] id 2 len 16 protocol IPCP 
(0x80210101000A03060A010102)
4d16h: BR0:2 CDPCP: I
4d16h CONFREQ [REQsent] id 1 len 4
4d16h: BR0:2 CDPCP: O CONFACK [REQsent] id 1 len 4
4d16h: BR0:2 BNCP: I CONFACK [ACKsent] id 1 len 4
4d16h: BR0:2 BNCP: State is Open
4d16h: BR0:2 CDPCP: I CONFACK [ACKsent] id 1 len 4
4d16h: BR0:2 CDPCP: State is Open
4d16h: BR0:2 DDR: dialer protocol up
4d16h: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, changed state to up
4d16h: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 
<unknown phone number> Venus   

!--- Unknown phone number because of no dialer string on Saturn

Saturn#

Discusiones relacionadas de la comunidad de soporte de Cisco

La Comunidad de Soporte de Cisco es un foro donde usted puede preguntar y responder, ofrecer sugerencias y colaborar con colegas.


Información Relacionada


Document ID: 10381