Marcado y acceso remotos : "Red digital de servicios integrados (ISDN), Señalización por canal asociado (CAS)"

Puenteo de respaldo sobre ISDN

17 Octubre 2016 - Traducción Automática
Otras Versiones: PDFpdf | Inglés (22 Agosto 2015) | Comentarios


Contenido


Introducción

Este documento explica y proporciona un ejemplo de cómo configurar el puenteo de respaldo con ISDN. Esta configuración usa el método de interfaz de respaldo para identificar que el link principal está desactivado. Para más información sobre el respaldo, vea configurar y resolver problemas el backup DDR.

En los entornos WAN interligados, la única solución de backup del Dial-on-Demand Routing (DDR) disponible es el uso del ISDN, pues el interligar sobre el async no se soporta.

Sea consciente que el interligar en una conexión ISDN tiende a mantener la conexión activa por mismo los períodos prolongados, si no permanentemente. Si la compañía telefónica (compañía telefónica) carga para el ISDN basado en el tiempo de conexión y el link serial se sigue que está abajo por mismo un tiempo prolongado, éste puede dar lugar a una cuenta muy grande.

Nota: Esta configuración es para un sitio y un canal B. Para más de un canal B, usted debe utilizar los Perfiles de marcado. (Refiera a los Perfiles de marcado que configuran para interligar usando Configuración de isdn.)

Para la información sobre el configuración de Bridging en un entorno del NON-respaldo, vea el Bridging Across ISDN.

prerrequisitos

Requisitos

Antes de utilizar esta configuración, asegúrese de que cumple con los siguientes requisitos:

  • Poseer un conocimiento básico de ISDN.

Componentes Utilizados

La información que contiene este documento se basa en las siguientes versiones de software y hardware.

  • Cisco 2500 Series Router con una interfaz serial PÁLIDA y una interfaz BRI cada uno.

  • Software Release 12.2(7b) del ½ del ¿Â de Cisco IOSïÂ.

Nota: Esta configuración puede usarse con cualquier router que tenga un link de WAN (de serie) y un puerto BRI.

La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener cualquier comando.

Productos Relacionados

Esta configuración puede utilizarse con cualquier par de routers que ejecuten el software del IOS de Cisco y cada uno debe tener al menos una interfaz serial WAN y una interfaz BRI.

Convenciones

Para obtener más información sobre las convenciones del documento, consulte Convenciones de Consejos Técnicos de Cisco.

Configurar

En esta sección encontrará la información para configurar las funciones descritas en este documento.

Nota: Para obtener información adicional sobre los comandos que se utilizan en este documento, use la Command Lookup Tool (solo para clientes registrados).

Diagrama de la red

En este documento, se utiliza esta configuración de red:

/image/gif/paws/10371/bridging.gif

Configuraciones

En este documento, se utilizan estas configuraciones:

Router1
!
hostname ROUTER1
!
!
username ROUTER2 password 0 same

!--- This is required for PPP Challenge Handshake Authentication Protocol
!--- (CHAP) authentication during dial backup.

!
!
isdn switch-type basic-5ess

!--- The ISDN switch type for this circuit. 
!--- Obtain this information from the Telco.
!--- This ISDN switch type is specific to the United States,
!--- and could change based on the requirements of the country and Telco.

!
interface Ethernet0
 ip address 172.16.55.33 255.255.255.240
 no ip directed-broadcast
 no ip mroute-cache
 bridge-group 1  

!--- Assign this interface to bridge-group 1.
!--- Frames are bridged only among interfaces in the same group.
!--- Note that the BRI interface and serial interface are also 
!--- in this bridge-group 1.

!
interface Serial0
 description Serial link to ROUTER2
 backup interface BRI0 

!--- This defines the backup interface. 
!--- Cisco IOS Software tracks the Serial0 interface, and
!--- uses BRI0 if Serial0 fails.

 ip address 172.16.54.1 255.255.255.0
 no ip directed-broadcast
 no ip mroute-cache
 no fair-queue
 bridge-group 1  

!--- Enable bridging on Serial0 for normal operation. 

!
interface BRI0
 description ISDN to ROUTER2
 ip address 172.16.53.19 255.255.255.240
 no ip directed-broadcast
 encapsulation ppp
 no ip mroute-cache
 dialer map bridge name ROUTER2 broadcast 5552000 

!--- The broadcast keyword is required to initiate the ISDN call.
!--- Dialer map bridge to the remote router. The statement includes
!--- the name of the remote router and the phone number to be dialed.
!--- Note that this dialer map statement includes the keyword bridge,
!--- and does not include the IP address of the peer, as required for
!--- IP routing-based dialer maps.

 dialer-group 1 

!--- Defines the interesting traffic as configured in the dialer-list.

 isdn switch-type basic-5ess 

!--- Check with your Telco for the correct values.

 ppp authentication chap
bridge-group 1 

!--- Enable bridging on BRI0.

!
dialer-list 1 protocol bridge permit 

!--- Defines the interesting traffic. In this case, all bridged traffic.

bridge 1 protocol ieee

!--- Defines the type of Spanning Tree Protocol (STP) used for the
!--- interface in bridge-group 1. Here, the IEEE STP is used.
!--- The IEEE 802.1D STP is the preferred way to run the bridge.

!

Router2
hostname router2
!
!
username ROUTER1 password 0 same 

!--- Required for PPP CHAP Authentication during dial backup.

!
isdn switch-type basic-5ess 

!--- Check with your Telco at the Router2 side for the correct values.   

!
interface Ethernet0
 ip address 172.16.55.2 255.255.255.240
 bridge-group 1 

!--- Enable bridging on Ethernet0.

!
interface Serial0
 description Serial link to ROUTER1 

!--- The backup interface bri0 command is not required on this side,
!--- because it is sufficient if one side tracks the serial interface.

 ip address 172.16.54.2 255.255.255.0 
 no fair-queue
 bridge-group 1 

!--- Enable bridging on Serial0 for normal operation.

interface BRI0
 description ISDN to ROUTER1
 ip address 172.16.53.17 255.255.255.240
 encapsulation ppp 
 no ip mroute-cache
 dialer map bridge name ROUTER1 broadcast 5551000 

!--- The broadcast keyword is required to initiate the ISDN call.

 dialer-group 1 

!--- Defines the interesting traffic as configured in the dialer-list.

 isdn switch-type basic-5ess 

!--- Check with your Telco at the Router2 side for the correct values.

 ppp authentication chap 
 bridge-group 1 

!--- Enable bridging on BRI0.

!
dialer-list 1 protocol bridge permit 

!--- Defines the interesting traffic. In this case, all bridged traffic.

bridge 1 protocol ieee

!--- Defines the type of STP used for the interface in 
!--- bridge-group 1. Here the IEEE STP is used. 
!--- The IEEE 802.1D STP is the preferred way to run the bridge.

!

Verificación

En esta sección encontrará información que puede utilizar para comprobar que su configuración funcione correctamente.

La herramienta Output Interpreter (sólo para clientes registrados) permite utilizar algunos comandos “show” y ver un análisis del resultado de estos comandos.

  • isdn status de la demostración — visualiza el Layer 1 (L1), la capa 2 (L2), y acoda 3 el estatus (L3) de las interfaces de ISDN.

  • marcador de la demostración — visualiza el estatus del marcador y el estado individual de los canales ISDN.

  • Bridge de la demostración — clases de las visualizaciones de entradas en el Bridge Forwarding Database.

  • interfaz de la demostración — visualiza el estatus de las diversas interfaces, tales como el serial y las interfaces BRI.

  • atravesar-árbol de la demostración — visualiza la topología del árbol de expansión sabida al router.

Comandos show en ROUTER1 cuando Serial0 está activo.

ROUTER1# show isdn status
   Global ISDN Switchtype = basic-5ess
   ISDN BRI0 interface
   dsl 0, interface ISDN Switchtype = basic-5ess
   Layer 1 Status:
   DEACTIVATED
   Layer 2 Status:
   Layer 2 NOT Activated
   Layer 3 Status:
   0 Active Layer 3 Call(s)
   Activated dsl 0 CCBs = 0
   The Free Channel Mask: 0x80000003
   Number of L2 Discards = 36, L2D_Task Discards = 35
   Total Allocated ISDN CCBs = 0

ROUTER1# show dialer

BRI0 - dialer type = ISDN

Dial String Successes Failures Last DNIS Last status
   5552000 29 977 00:45:08 successful
   0 incoming call(s) have been screened.
   0 incoming call(s) rejected for callback.

BRI0:1 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is shutdown

BRI0:2 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is shutdown

ROUTER1# show bridge

Total of 300 station blocks, 298 free
   Codes: P - permanent, S - self

Bridge Group 1:

 Address Action Interface Age RX count TX count
   0000.0c76.2882 forward Serial0 0 5 4

!--- Bridging traffic goes through Serial0.

   00d0.58ad.ae13 forward Ethernet0 0 42 5

Comandos show en ROUTER1 cuando Serial0 está inactivo.

ROUTER1# show isdn status
   Global ISDN Switchtype = basic-5ess
   ISDN BRI0 interface
   dsl 0, interface ISDN Switchtype = basic-5ess
   Layer 1 Status:
   ACTIVE
   Layer 2 Status:
   TEI = 114, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

   !--- ISDN L1 and L2 will be up (when Serial0 fails)
   !--- even if interesting traffic is not present.

   Layer 3 Status:
   1 Active Layer 3 Call(s)
   Activated dsl 0 CCBs = 1
   CCB:callid=8484, sapi=0, ces=1, B-chan=1, calltype=DATA
   The Free Channel Mask: 0x80000002
   Total Allocated ISDN CCBs = 1

ROUTER1# show dialer

BRI0 - dialer type = ISDN

Dial String Successes Failures Last DNIS Last status
   5552000 30 977 00:00:16 successful
   0 incoming call(s) have been screened.
   0 incoming call(s) rejected for callback.

BRI0:1 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up
   Dial reason: bridge (0xFFFF)
   Time until disconnect 106 secs
   Connected to 5552000 (ROUTER2)

BRI0:2 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is idle
   
ROUTER1# show bridge

Total of 300 station blocks, 298 free
   Codes: P - permanent, S - self

Bridge Group 1:

 Address Action Interface Age RX count TX count
   0000.0c76.2882 forward BRI0 0 5 4	

!--- Bridging traffic now goes through BRI0.

   00d0.58ad.ae13 forward Ethernet0 0 5 5

Troubleshooting

En esta sección encontrará información que puede utilizar para solucionar problemas de configuración.

Recursos de resolución de problemas

Utilice estos recursos como sea necesario:

Comandos para resolución de problemas

La herramienta Output Interpreter (sólo para clientes registrados) permite utilizar algunos comandos “show” y ver un análisis del resultado de estos comandos.

Nota: Antes de ejecutar un comando de depuración, consulte Información importante sobre comandos de depuración.

  • debug dialer — proporciona la información sobre los eventos de la interfaz del dialer.

  • debug isdn event — las visualizaciones hacen el debug de los mensajes relacionados con la actividad ISDN que ocurre en el lado del usuario de la interfaz de ISDN.

  • debug ISDN q931 — proporciona la información sobre la configuración de la llamada y cierre de las conexiones de red ISDN (L3) entre el router local (lado del usuario) y la red.

  • el debug isdn q921 — las visualizaciones hace el debug de los mensajes relacionados con los procedimientos de acceso de la capa del link de datos (L2) que ocurren en el router en el canal D (LAPD) de su interfaz de ISDN.

  • negociación ppp del debug — las visualizaciones hacen el debug de los mensajes relacionados con la negociación de opciones PPP y los parámetros del protocolo network control (NCP).

  • autenticación PPP del debug — Los mensajes del debug de las visualizaciones se relacionaron con el intercambio de los paquetes de la GRIETA y del protocolo password authentication (PAP).

depurar salida en ENRUTADOR1 cuando serial0 desciende e ISDN se levanta

ROUTER1# show debug
   Dial on demand:
   Dial on demand events debugging is on
   PPP:
   PPP authentication debugging is on
   PPP protocol negotiation debugging is on
   ISDN:
   ISDN events debugging is on
   ISDN Q921 packets debugging is on
   ISDN Q931 packets debugging is on

ROUTER1#

!--- Interface serial0 goes down.

ROUTER1#
00:56:53: %LINK-3-UPDOWN: Interface Serial0, changed state to down
*Mar  1 00:56:53.103: ISDN BR0 EVENT: isdn_sw_cstate: State = 0,
 Old State = 6
00:56:53: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
*Mar  1 00:56:53.107: BR0:1 LCP: State is Closed
*Mar  1 00:56:53.111: BR0:1 DDR: disconnecting call
00:56:53: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
*Mar  1 00:56:53.119: BR0:2 LCP: State is Closed
*Mar  1 00:56:53.119: BR0:2 DDR: disconnecting call
*Mar  1 00:56:53.127: ISDN BR0 EVENT: isdn_sw_cstate: State = 4,
 Old State = 6
*Mar  1 00:56:53.135: ISDN BR0 EVENT: isdn_sw_cstate: State = 4,
 Old State = 6
*Mar  1 00:56:53.567: ISDN BR0: RX <- IDCKRQ ri=0 ai=127
*Mar  1 00:56:53.567: ISDN Recvd L1 prim 3 dsl 0 state 3 ctrl_state 0
*Mar  1 00:56:53.571: ISDN BR0: L1 persistent Deactivated
*Mar  1 00:56:53.571: ISDN Recvd L1 prim 7 dsl 0 state 3 ctrl_state 0
*Mar  1 00:56:53.575: ISDN BR0: Recvd MPH_IIC_IND from L1
*Mar  1 00:56:53.575: ISDN Recvd L1 prim 7 dsl 0 state 3 ctrl_state 0
*Mar  1 00:56:53.579: ISDN BR0: Recvd MPH_IIC_IND from L1
*Mar  1 00:56:53.579: ISDN Recvd L1 prim 1 dsl 0 state 3 ctrl_state 0
*Mar  1 00:56:53.583: ISDN BR0: L1 is IF_ACTIVE
*Mar  1 00:56:53.583: ISDN BR0 EVENT: isdn_sw_cstate: State = 4,
 Old State = 6
*Mar  1 00:56:53.587: ISDN BR0: L2-TERM: ces/tei=1/0
 AWAIT_ESTABLISH->TERM_DOWN
*Mar  1 00:56:53.591: ISDN BR0: Incoming call id = 0x0010, dsl 0
*Mar  1 00:56:53.595: ISDN BR0: L2-TERM: ces/tei=1/0
 TERM_DOWN->AWAIT_ESTABLISH
00:56:53: %LINK-3-UPDOWN: Interface BRI0, changed state to up
*Mar  1 00:56:53.631: ISDN BR0 EVENT: isdn_sw_cstate: State = 4,
 Old State = 6
*Mar  1 00:56:53.655: ISDN BR0: TX -> IDREQ ri=48769 ai=127
00:56:54: %LINEPROTO-5-UPDOWN: 
Line protocol on Interface Serial0, changed state to down
*Mar  1 00:56:54.387: ISDN BR0: RX <- IDCKRQ ri=0 ai=127
*Mar  1 00:56:55.655: ISDN BR0: TX -> IDREQ ri=42642 ai=127
*Mar  1 00:56:55.699: ISDN BR0: RX <- IDASSN ri=42642 ai=68
*Mar  1 00:56:55.791: ISDN BR0: TX -> SABMEp c/r=0 sapi=0 tei=68
*Mar  1 00:56:55.823: ISDN BR0: RX <- UAf c/r=0 sapi=0 tei=68
00:56:55: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0,
TEI 68 changed to up
*Mar  1 00:56:55.831: ISDN BR0: L2-TERM: ces/tei=1/68 
AWAIT_ESTABLISH->ESTABLISHED

!--- Interesting traffic has not arrived yet from Host1, 
!--- but ISDN L1 and L2 are up now.

ROUTER1# show isdn stat
Global ISDN Switchtype = basic-5ess
ISDN BRI0 interface
        dsl 0, interface ISDN Switchtype = basic-5ess
    Layer 1 Status:
        ACTIVE
    Layer 2 Status:
        TEI = 68, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
        I_Queue_Len 0, UI_Queue_Len 0
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask:  0x80000003
    Number of L2 Discards = 0, L2 Session ID = 34
    Total Allocated ISDN CCBs = 0
ROUTER1#
*Mar  1 00:57:25.839: ISDN BR0: TX -> RRp sapi=0 tei=68 nr=0
*Mar  1 00:57:25.871: ISDN BR0: RX <- RRf sapi=0 tei=68 nr=0
ROUTER1#


!--- Interesting traffic arrives now, 
!--- which triggers ISDN Dialup (see below).

*Mar  1 00:57:32.519: BR0 DDR: Dialing cause bridge (0xFFFF)
*Mar  1 00:57:32.519: BR0 DDR: Attempting to dial 5552000
*Mar  1 00:57:32.523: ISDN BR0: Outgoing call id = 0x800E, dsl 0
*Mar  1 00:57:32.527: ISDN BR0: Event: Call to 5552000 at 64 Kb/s
*Mar  1 00:57:32.527: ISDN BR0: process_bri_call(): call id 0x800E, 
called_number 5552000, speed 64, call type DATA
*Mar  1 00:57:32.531: CCBRI_Go Fr Host InPkgInfo (Len=22) :
*Mar  1 00:57:32.535: 1 0 1 80 E 0 4 2 88 90 18 
1 83 2C 7 35 35 35 32 30 30 30
*Mar  1 00:57:32.543:
*Mar  1 00:57:32.547: CC_CHAN_GetIdleChanbri: dsl 0
*Mar  1 00:57:32.547:     Found idle channel B1
*Mar  1 00:57:32.563: ISDN BR0: TX -> INFOc sapi=0 tei=68 ns=0 nr=0 
i=0x08010E05040288901801832C0735353532303030
*Mar  1 00:57:32.583:     SETUP pd = 8  callref = 0x0E
*Mar  1 00:57:32.591:         Bearer Capability i = 0x8890
*Mar  1 00:57:32.599:         Channel ID i = 0x83
*Mar  1 00:57:32.603:         Keypad Facility i = '5552000'
*Mar  1 00:57:32.867: ISDN BR0: RX <- INFOc sapi=0 tei=68 ns=0 nr=1 
i=0x08018E02180189
*Mar  1 00:57:32.875:     CALL_PROC pd = 8  callref = 0x8E
*Mar  1 00:57:32.883:         Channel ID i = 0x89
*Mar  1 00:57:32.899: ISDN BR0: TX -> RRr sapi=0 tei=68 nr=1
*Mar  1 00:57:32.907: CCBRI_Go Fr L3 pkt (Len=7) :
*Mar  1 00:57:32.907: 2 1 E 98 18 1 89
*Mar  1 00:57:32.911:
*Mar  1 00:57:32.915: ISDN BR0: LIF_EVENT: ces/callid 1/0x800E
 HOST_PROCEEDING
*Mar  1 00:57:32.919: ISDN BR0: HOST_PROCEEDING
*Mar  1 00:57:32.919: ISDN BR0: HOST_MORE_INFO
*Mar  1 00:57:33.159: ISDN BR0: RX <- INFOc sapi=0 tei=68 ns=1
 nr=1 i=0x08018E07
*Mar  1 00:57:33.167:     CONNECT pd = 8  callref = 0x8E
*Mar  1 00:57:33.183: ISDN BR0: TX -> RRr sapi=0 tei=68 nr=2
*Mar  1 00:57:33.191: CCBRI_Go Fr L3 pkt (Len=4) :
*Mar  1 00:57:33.191: 7 1 E 91
*Mar  1 00:57:33.195:
*Mar  1 00:57:33.199: ISDN BR0: LIF_EVENT: ces/callid 1/0x800E
 HOST_CONNECT
00:57:33: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
*Mar  1 00:57:33.215: ISDN: get_isdn_service_state(): 
idb 0x19F4D8 bchan 2 is_isdn 1 Not a Pri
*Mar  1 00:57:33.215: BR0:1 PPP: Treating connection as a callout
*Mar  1 00:57:33.219: BR0:1 PPP: Phase is ESTABLISHING,
 Active Open [0 sess, 1 load]
*Mar  1 00:57:33.223: BR0:1 LCP: O CONFREQ [Closed] id 27 len 15
*Mar  1 00:57:33.227: BR0:1 LCP:    AuthProto CHAP
 (0x0305C22305)
*Mar  1 00:57:33.231: BR0:1 LCP:    MagicNumber 0x6091A5F6
 (0x05066091A5F6)
*Mar  1 00:57:33.235: ISDN BR0: Event: Connected to 5552000
 on B1 at 64 Kb/s
*Mar  1 00:57:33.247: ISDN BR0: TX -> INFOc sapi=0 tei=68 ns=1 nr=2
 i=0x08010E0F
*Mar  1 00:57:33.251:     CONNECT_ACK pd = 8  callref = 0x0E
*Mar  1 00:57:33.267: BR0:1 LCP: I CONFREQ [REQsent] id 4 len 15
*Mar  1 00:57:33.271: BR0:1 LCP:    AuthProto CHAP
 (0x0305C22305)
*Mar  1 00:57:33.275: BR0:1 LCP:    MagicNumber 0x6062D6EA
 (0x05066062D6EA)
*Mar  1 00:57:33.279: BR0:1 LCP: O CONFACK [REQsent] id 4 len 15
*Mar  1 00:57:33.283: BR0:1 LCP:    AuthProto CHAP
 (0x0305C22305)
*Mar  1 00:57:33.287: BR0:1 LCP:    MagicNumber 0x6062D6EA
 (0x05066062D6EA)
*Mar  1 00:57:33.291: BR0:1 LCP: I CONFACK [ACKsent] id 27 len 15
*Mar  1 00:57:33.291: BR0:1 LCP:    AuthProto CHAP
 (0x0305C22305)
*Mar  1 00:57:33.295: BR0:1 LCP:    MagicNumber 0x6091A5F6
 (0x05066091A5F6)
*Mar  1 00:57:33.299: BR0:1 LCP: State is Open
*Mar  1 00:57:33.303: BR0:1 PPP: Phase is AUTHENTICATING,
 by both [0 sess, 1 load]
*Mar  1 00:57:33.307: BR0:1 CHAP: O CHALLENGE id 14
 len 28 from "ROUTER1"
*Mar  1 00:57:33.319: BR0:1 CHAP: I CHALLENGE id 4
 len 28 from "ROUTER2"
*Mar  1 00:57:33.327: BR0:1 CHAP: O RESPONSE id 4
 len 28 from "ROUTER1"
*Mar  1 00:57:33.335: ISDN BR0: RX <- RRr sapi=0
 tei=68 nr=2
*Mar  1 00:57:33.351: BR0:1 CHAP: I SUCCESS id 4
 len 4
*Mar  1 00:57:33.367: BR0:1 CHAP: I RESPONSE id 14
 len 28 from "ROUTER2"
*Mar  1 00:57:33.371: BR0:1 CHAP: O SUCCESS id 14
 len 4
*Mar  1 00:57:33.375: BR0:1 PPP: Phase is UP [0 sess, 0 load]
*Mar  1 00:57:33.379: BR0:1 BNCP: O CONFREQ [Closed] id 14
 len 4
*Mar  1 00:57:33.387: BR0:1 CDPCP: O CONFREQ [Closed] id 14
 len 4
*Mar  1 00:57:33.395: BR0:1 BNCP: I CONFREQ [REQsent] id 4
 len 4
*Mar  1 00:57:33.399: BR0:1 BNCP: O CONFACK [REQsent] id 4
 len 4
*Mar  1 00:57:33.403: BR0:1 IPCP: I CONFREQ [Not negotiated] id 4
 len 10
*Mar  1 00:57:33.407: BR0:1 IPCP:    Address 172.16.53.17
 (0x0306AC103511)
*Mar  1 00:57:33.415: BR0:1 LCP: O PROTREJ [Open] id 28
 len 16 protocol IPCP 
(0x80210104000A0306AC103511)
*Mar  1 00:57:33.419: BR0:1 CDPCP: I CONFREQ [REQsent] id 4
 len 4
*Mar  1 00:57:33.423: BR0:1 CDPCP: O CONFACK [REQsent] id 4
 len 4
*Mar  1 00:57:33.427: BR0:1 BNCP: I CONFACK [ACKsent] id 14
 len 4
*Mar  1 00:57:33.431: BR0:1 BNCP: State is Open
*Mar  1 00:57:33.435: BR0:1 CDPCP: I CONFACK [ACKsent] id 14
 len 4
*Mar  1 00:57:33.439: BR0:1 CDPCP: State is Open
*Mar  1 00:57:33.443: BR0:1 DDR: dialer protocol up
00:57:34: %LINEPROTO-5-UPDOWN: 
Line protocol on Interface BRI0:1, changed state to up
00:57:39: %ISDN-6-CONNECT: Interface BRI0:1 is now connected
 to 5552000 ROUTER2
ROUTER1#

ROUTER1# show isdn status
Global ISDN Switchtype = basic-5ess
ISDN BRI0 interface
        dsl 0, interface ISDN Switchtype = basic-5ess
    Layer 1 Status:
        ACTIVE
    Layer 2 Status:
        TEI = 68, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
        I_Queue_Len 0, UI_Queue_Len 0
    Layer 3 Status:
        1 Active Layer 3 Call(s)
        CCB:callid=800E, sapi=0, ces=1, B-chan=1, calltype=DATA
    Active dsl 0 CCBs = 1
    The Free Channel Mask:  0x80000002
    Number of L2 Discards = 0, L2 Session ID = 34
    Total Allocated ISDN CCBs = 1
*Mar  1 00:58:03.343: ISDN BR0: TX -> RRp sapi=0 tei=68 nr=2
*Mar  1 00:58:03.379: ISDN BR0: RX <- RRf sapi=0 tei=68 nr=2pann
ROUTER1# show spanning-tree

 Bridge group 1 is executing the ieee compatible Spanning Tree protocol
   Bridge Identifier has priority 32768, address 0060.5cf4.a9a8
   Configured hello time 2, max age 20, forward delay 15
   Current root has priority 32768, address 0060.5cf4.a955
   Root port is 3 (BRI0), cost of root path is 15625
   Topology change flag set, detected flag not set
   Number of topology changes 10 last change occurred 00:01:15 ago
   from Serial0
   Times: hold 1, topology change 35, notification 2
   hello 2, max age 20, forward delay 15
   Timers: hello 0, topology change 0, notification 0, aging 15

 Port 2 (Ethernet0) of Bridge group 1 is forwarding
   Port path cost 100, Port priority 128, Port Identifier 128.2.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.2, designated path cost 15625
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   BPDU: sent 751, received 0

 Port 3 (BRI0) of Bridge group 1 is forwarding    

!---  BRI Interface forwards the bridged traffic now.

   Port path cost 15625, Port priority 128, Port Identifier 128.3.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a955
   Designated port id is 128.3, designated path cost 0
   Timers: message age 2, forward delay 0, hold 0
   Number of transitions to forwarding state: 3
   BPDU: sent 1014, received 608

 Port 6 (Serial0) of Bridge group 1 is down
   Port path cost 647, Port priority 128, Port Identifier 128.6.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.6, designated path cost 15625
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 1
   BPDU: sent 15, received 27

ROUTER1#
   *Mar 1 00:58:33.387: ISDN BR0: TX -> RRp sapi=0 tei=68 nr=2
   *Mar 1 00:58:33.423: ISDN BR0: RX <- RRf sapi=0 tei=68 nr=2

depurar salida en ENRUTADOR 1 cuando Serial0 regrese e ISDN interrumpe la llamada

00:58:37: %LINK-3-UPDOWN: Interface Serial0, changed state to up
   *Mar 1 00:58:37.671: BR0:1 DDR: disconnecting call
   *Mar 1 00:58:37.675: BR0:2 DDR: disconnecting call
   *Mar 1 00:58:37.675: ISDN BR0: Event: Hangup call to call id 0x800E
   *Mar 1 00:58:37.679: ISDN BR0: process_disconnect(): call id 0x800E,
    call type is DATA, b_idb 0x19F4D8, ces 1, cause Normal call
   clearing(0x10)
   00:58:37: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from
   5552000 ROUTER2, call lasted 64 seconds
   *Mar 1 00:58:37.691: ISDN: get_isdn_service_state(): idb 0x19F4D8
    bchan 2 is_isdn 1 Not a Pri
   *Mar 1 00:58:37.695: CCBRI_Go Fr Host InPkgInfo (Len=13) :
   *Mar 1 00:58:37.699: 5 0 1 80 E 3 8 1 90 8 2 80 90
   *Mar 1 00:58:37.703:
   *Mar 1 00:58:37.719: ISDN BR0: TX -> INFOc sapi=0 tei=68 ns=2 nr=2 
    i=0x08010E4508028090
   *Mar 1 00:58:37.727: DISCONNECT pd = 8 callref = 0x0E
   *Mar 1 00:58:37.735: Cause i = 0x8090 - Normal call clearing
   *Mar 1 00:58:37.743: ISDN BR0 EVENT: isdn_sw_cs!!!!!!!!!!!!!!!!!!!tate:
    State = 6, Old State = 4
   00:58:37: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
   *Mar 1 00:58:37.751: BR0:1 BNCP: State is Closed
   *Mar 1 00:58:37.755: BR0:1 CDPCP: State is Closed
   *Mar 1 00:58:37.755: BR0:1 PPP: Phase is TERMINATING [0 sess, 1 load]
   *Mar 1 00:58:37.759: BR0:1 LCP: State is Closed
   *Mar 1 00:58:37.763: BR0:1 PPP: Phase is DOWN [0 sess, 1 load]
   *Mar 1 00:58:37.763: BR0:1 DDR: disconnecting call
   *Mar 1 00:58:37.775: ISDN Recvd L1 prim 3 dsl 0 state 1 ctrl_state 0
   *Mar 1 00:58:37.779: ISDN BR0: Physical layer is IF_DOWN
   *Mar 1 00:58:37.783: ISDN BR0: Shutting down ME
   00:58:37: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0,
    TEI 68 changed to down
   *Mar 1 00:58:37.791: ISDN BR0: L2-TERM: ces/tei=1/68
    ESTABLISHED->TERM_DOWN
   *Mar 1 00:58:37.795: ISDN BR0: LIF_EVENT: ces/callid 1/0x800E
    HOST_DISCONNECT_ACK
   *Mar 1 00:58:37.803: ISDN: get_isdn_service_state(): idb 0x19F4D8
    bchan 2 is_isdn 1 Not a Pri
   *Mar 1 00:58:37.807: ISDN BR0: HOST_DISCONNECT_ACK: call type is DATA
   00:58:37: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
   *Mar 1 00:58:37.815: BR0:1 LCP: State is Closed
   *Mar 1 00:58:37.815: BR0:1 DDR: disconnecting call
   *Mar 1 00:58:37.819: ISDN BR0: Shutting down ISDN Layer 3
   00:58:37: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0,
    TEI 68 changed to down
   00:58:37: %LINK-5-CHANGED: Interface BRI0, changed state to standby mode
   *Mar 1 00:58:37.847: ISDN BR0 EVENT: isdn_sw_cstate: State = 6,
   Old State = 4
   00:58:37: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
   *Mar 1 00:58:37.855: BR0:2 LCP: State is Closed
   *Mar 1 00:58:37.855: BR0:2 DDR: disconnecting call
   *Mar 1 00:58:37.895: ISDN BR0: Incoming call id = 0x0011, dsl 0
   *Mar 1 00:58:37.895: ISDN BR0: L2-TERM: ces/tei=1/0
    TERM_DOWN->AWAIT_ESTABLISH
   *Mar 1 00:58:37.935: ISDN BR0: Activating
   00:58:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
   changed state to up
   00:58:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1,
   changed state to down
   *Mar 1 00:58:39.939: ISDN BR0: Could not bring up interface
   *Mar 1 00:58:39.943: ISDN BR0: Shutting down ISDN Layer 3
   *Mar 1 00:58:39.963: ISDN BR0: Activating
   *Mar 1 00:58:41.943: ISDN BR0: Could not bring up interface
   *Mar 1 00:58:41.947: ISDN BR0: Shutting down ISDN Layer 3
   *Mar 1 00:58:41.947: ISDN BR0: Activating
   ROUTER1#
   
   ROUTER1# show isdn status
   Global ISDN Switchtype = basic-5ess
   ISDN BRI0 interface
   dsl 0, interface ISDN Switchtype = basic-5ess
   Layer 1 Status:
   DEACTIVATED
   Layer 2 Status:
   Layer 2 NOT Activated         

!--- ISDN L1 and L2 are back to the deactivated state.

   Layer 3 Status:
   0 Active Layer 3 Call(s)
   Active dsl 0 CCBs = 0
   The Free Channel Mask: 0x80000003
   Number of L2 Discards = 0, L2 Session ID = 39
   Total Allocated ISDN CCBs = 0
   ROUTER1#
   *Mar 1 00:58:49.951: ISDN BR0: Could not bring up interface
   *Mar 1 00:58:49.951: ISDN BR0: Shutting down ISDN Layer 3
   ROUTER1#

ROUTER1# show spanning-tree

 Bridge group 1 is executing the ieee compatible Spanning Tree protocol
   Bridge Identifier has priority 32768, address 0060.5cf4.a9a8
   Configured hello time 2, max age 20, forward delay 15
   Current root has priority 32768, address 0060.5cf4.a955
   Root port is 6 (Serial0), cost of root path is 647
   Topology change flag not set, detected flag not set
   Number of topology changes 13 last change occurred 00:28:23 ago
   from Serial0
   Times: hold 1, topology change 35, notification 2
   hello 2, max age 20, forward delay 15
   Timers: hello 0, topology change 0, notification 0, aging 300

 Port 2 (Ethernet0) of Bridge group 1 is forwarding
   Port path cost 100, Port priority 128, Port Identifier 128.2.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.2, designated path cost 647
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   BPDU: sent 1633, received 0

 Port 3 (BRI0) of Bridge group 1 is down

!--- BRI0 is in the down state when Serial 0 is up.

   Port path cost 15625, Port priority 128, Port Identifier 128.3.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.3, designated path cost 647
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 3
   BPDU: sent 1014, received 622

 Port 6 (Serial0) of Bridge group 1 is forwarding 

!--- Serial0 forwards the bridged traffic now.

   Port path cost 647, Port priority 128, Port Identifier 128.6.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a955
   Designated port id is 128.6, designated path cost 0
   Timers: message age 1, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   BPDU: sent 18, received 896
ROUTER1#

Información Relacionada


Document ID: 10371