长距离以太网 (LRE) 和数字用户线 (xDSL) : LRE/VDSL(长距离以太网/超高数据速率 DSL)

华为MA5600 DSL访问复用器线路培训配置示例

2016 年 10 月 27 日 - 机器翻译
其他版本: PDFpdf | 英语 (2015 年 8 月 22 日) | 反馈

简介

本文在Cisco用户前提设备(CPE)描述在华为MA5600数字用户线路访问多路复用器要求的最低配置步骤为了允许Very-high bit rate Digital Subscriber Line (VDSL)培训。

贡献用Utsav杜德, Cisco TAC工程师。

先决条件

要求

思科建议您符合这些要求,在您尝试此配置前:  

  • 缚住紧密地连接在CPE的VDSL端口和在DSLAM的配线面板的正确端口
  • CPE和DSLAM/线卡一定是正在运行的

使用的组件

本文档中的信息根据作为CPE和虎尾5600 DSLAM的思科887VA路由器。然而,本文没有限制对特定软件和硬件版本。

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始(默认)配置。如果您使用的是真实网络,请确保您已经了解所有命令的潜在影响。

背景

本文打算帮助工程师设置Cisco CPE和一个华为DSLAM在背对背/实验室环境和了解基本配置文件在DSL中心局结尾。

配置

完成这些部分为了配置您的设备:

  • 线路配置文件配置
  • 信道配置文件配置
  • 线路模板(线路配置文件和信道配置文件的组合)配置
  • 运用在CPE连接的各自DSLAM波尔特的线路模板

注意:使用命令查找工具仅限注册用户)可获取有关本部分所使用命令的详细信息。

线路配置文件配置

  1. 检查已经创建的线路配置文件。
    MA5600#display vdsl line-profile

    { <cr>|profile-index<U><1,128> }:

      Command:
              display vdsl line-profile
      ------------------------------------------------------------------------------
      Profile  Profile                          Transmission
      Index    Name                             Mode
      ------------------------------------------------------------------------------
           60  Test_vdsl                        VDSL (G993.2)
           82  VDSL LINE PROFILE 82             VDSL (G993.2)
           88  VDSL LINE PROFILE 88             VDSL (G993.2)
          103  VDSL LINE PROFILE 103            VDSL (G993.2)
      ------------------------------------------------------------------------------
      Total: 4
  2. 配置线路配置文件。
    MA5600#config

    MA5600(config)#vdsl line-profile add 60
      Failure: The profile has existed

    MA5600(config)#vdsl line-profile add 61
      Start adding profile
      Press 'Q' to quit the current configuration and new configuration will be

    >  Do you want to name the profile (y/n) [n]:y
    >    Please input profile name:ZONE_TEST
    >    Transmission mode:
    >      0: Custom
    >      1: All (G992.1~5,T1.413,G993.2)
    >      2: Full rate(G992.1/3/5,T1.413,G993.2)
    >      3: G.DMT (G992.1/3/5,G993.2)
    >      4: G.HS (G992.1~5,G993.2)
    >      5: ADSL (G.992.1~5,T1.413)
    >      6: VDSL (G993.2)
    >    Please select (0~6) [1]:6 >>>>>>>>>>>>>>>>>> Selecting Transmission Mode as VDSL
    >  Bit swap downstream 1-disable 2-enable (1~2) [2]:1
    >  Bit swap upstream   1-disable 2-enable (1~2) [2]:1
    >  Please select the form of transmit rate adaptation downstream:
    >  1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
    >  Please select the form of transmit rate adaptation upstream:
    >  1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
    >  Will you set SNR margin parameters? (y/n) [n]:
    >  Will you set DPBO parameters? (y/n)[n]:
    >  Will you set UPBO parameters? (y/n)[n]:
    >  Will you set RFI notch configuration parameter? (y/n) [n]:
    >  Will you set VDSL tone blackout configuration parameter? (y/n) [n]:
    >  Will you set mode-specific parameters? (y/n) [n]:
      Add profile 61 successfully

    MA5600#display vdsl line-profile
    { <cr>|profile-index<U><1,128> }:

      Command:
              display vdsl line-profile
      ------------------------------------------------------------------------------
      Profile  Profile                          Transmission
      Index    Name                             Mode
      ------------------------------------------------------------------------------
           60  Test_vdsl                        VDSL (G993.2)
           61  ZONE_TEST                        VDSL (G993.2)
           82  VDSL LINE PROFILE 82             VDSL (G993.2)
           88  VDSL LINE PROFILE 88             VDSL (G993.2)
          103  VDSL LINE PROFILE 103            VDSL (G993.2)
      ------------------------------------------------------------------------------
      Total: 5

信道配置文件配置

  1. 检查已经创建的信道配置文件。
    MA5600#display vdsl channel-profile
    { <cr>|profile-index<U><1,128> }:

      Command:
              display vdsl channel-profile
      ------------------------------------------------------------------------------
      Profile  Profile            MinDw    MaxDw    MinUp    MaxUp   Data Path
      Index    Name               Rate     Rate     Rate     Rate    Mode
      ------------------------------------------------------------------------------
           60  test_vdsl      128   100000      128   100000   Both
           99  VDSL CHANNEL PRO     128   100000      128   100000   PTM
               FILE 99
      ------------------------------------------------------------------------------
      Total: 2

    注意:速率单元是Kbps。

  2. 配置信道配置文件。
    MA5600(config)#vdsl channel-profile add 60
      Failure: The profile has existed

    MA5600(config)#vdsl channel-profile add 61
      Start adding profile
      Press 'Q' to quit the current configuration and new configuration will be
    neglected
    >  Do you want to name the profile (y/n) [n]:y
    >    Please input profile name:ZONE_TEST
    >  Data path mode 1-ATM, 2-PTM, 3-Both (1~3) [3]:2 >>>>>>>>>>>>>>>>>>>>>> PTM Mode
    >  Will you set the minimum impulse noise protection? (y/n) [n]:
    >  Will you set interleaving delay parameters? (y/n) [n]:
    >  Will you set parameters for rate? (y/n) [n]:
    >  Will you set rate thresholds? (y/n) [n]:
      Add profile 61 successfully

    MA5600#display vdsl channel-profile
    { <cr>|profile-index<U><1,128> }:

      Command:
              display vdsl channel-profile
      ------------------------------------------------------------------------------
      Profile  Profile            MinDw    MaxDw    MinUp    MaxUp   Data Path
      Index    Name               Rate     Rate     Rate     Rate    Mode
      ------------------------------------------------------------------------------>
           60  test_vdsl      128   100000      128   100000   Both
           61  ZONE_TEST      128   100000      128   100000   PTM
           99  VDSL CHANNEL PRO     128   100000      128   100000   PTM
               FILE 99
      ------------------------------------------------------------------------------
      Total: 3

    注意:速率单元是Kbps。

线路模板配置

  1. 检查已经创建的线路模板。
    MA5600#display vdsl line-template
    { <cr>|template-index<U><1,128> }:

      Command:
              display vdsl line-template
      ------------------------------------------------------------------------------
      Template  Template         Line Profile  Channel1       Channnel2
      Index     Name             Index         Profile Index  Profile Index
      ------------------------------------------------------------------------------
            12  ios_test                   10             11              -
            16  DT-17a                     18             18              -
            17  profile_17a                17             17              -
            18  aj_3M_US                   17              5              -
            60  VDSL LINE TEMPLA           60             60              -
                TE 60
      ------------------------------------------------------------------------------
      Total: 5
  2. 配置线路模板。
    MA5600(config)#vdsl line-template add 61
      Start adding template
      Press 'Q' to quit the current configuration and new configuration will be
    neglected
    >  Do you want to name the template (y/n) [n]:y
    >    Please input template name:ZONE_TEST
    Please set the line-profile index (1~128) [1]:61 >>>>>>>>>>>>>>>>Line Profile
    we added above

    >  Will you set channel configuration parameters? (y/n) [n]:y
    >    Please set the channel number (1~2) [1]:
    >    Channel1 configuration parameters:
    >    Please set the channel-profile index (1~128) [1]:61 >>>>>> Channel Profile
    we added above

      Add template 61 successfully

    MA5600#display vdsl line-template
    { <cr>|template-index<U><1,128> }:

      Command:
              display vdsl line-template
      ------------------------------------------------------------------------------
      Template  Template         Line Profile  Channel1       Channnel2
      Index     Name             Index         Profile Index  Profile Index
      ------------------------------------------------------------------------------
            12  ios_test                   10             11              -
            16  DT-17a                     18             18              -
            17  profile_17a                17             17              -
            18  aj_3M_US                   17              5              -
            60  VDSL LINE TEMPLA           60             60              -
                TE 60
            61  ZONE_TEST                  61             61              -
      ------------------------------------------------------------------------------
      Total: 6

运用线路模板对DSLAM波尔特

在这种情况下, CPE连接到华为DSLAM的Slot 5端口0。

MA5600(config)#display board 0
  -------------------------------------------------------------------------
  SlotID  BoardName  Status        SubType0 SubType1
  -------------------------------------------------------------------------
  0       H563ADGE   Failed
  1       H565ADBF   Normal >>>>>>>>>ADBF - Here 'A' means that this card supports ADSL
  2       ADG        Failed
  3       H569SHEB   Failed
  4
  5       H565VDBD   Normal >>>> >>>>VDBD - Here 'V' means that this card supports VDSL
  6
  7       H561SCU    Standby_normal O2FM >>>>>>>>>>>>>>>>>>>>>> Processor Cards
  8       H561SCU    Active_normal  O2GS     O2GS >>>>>>>>>>>>> Processor Cards
  9
  10
  11      H565VDBD   Failed
  12      H569SHEB   Failed
  13
  14      H561SHEA   Failed
  15
  -------------------------------------------------------------------------

MA5600(config)#interface vdsl 0/5 (Board/ slot)

Check the port status: Status is deactivated and currently assigned to
Line Template 1 (default)

MA5600(config-if-vdsl-0/5)#display port state 0
  -----------------------------------------------------------------
  Port     Status        Loopback    Line Template   Alarm Template
  -----------------------------------------------------------------
     0     Deactivated   Disable                1                1
  -----------------------------------------------------------------

分配线路模板(61)到端口(0/5/0)

MA5600(config-if-vdsl-0/5)#activate 0 template-index 61 
>>>>>>>> We are already in board 0 slot 5, hence need to activate port 0 with
Line Template 61

MA5600(config-if-vdsl-0/5)#display port state 0
  ---------------------------------------------------------------
  Port   Status        Loopback    Line Template   Alarm Template
  ---------------------------------------------------------------
     0   Activating    Disable                61                1 >>>>>Check the status
  ---------------------------------------------------------------

MA5600(config-if-vdsl-0/5)#display port state 0
  -----------------------------------------------------------------
  Port   Status        Loopback    Line Template   Alarm Template
  ---------------------------------------------------------------
     0   Activated     Disable                61                1 >>Status is activated
  ---------------------------------------------------------------

验证

使用此部分以验证配置。

命令输出解释程序工具仅限注册用户)支持某些 show 命令。请使用Output Interpreter Tool为了查看show命令输出分析。

在DSLAM的验证

检查创建的线路配置文件

MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:

  Command:
          display vdsl line-profile
  ------------------------------------------------------------------------------
  Profile  Profile                          Transmission
  Index    Name                             Mode
  ------------------------------------------------------------------------------
       60  Test_vdsl                        VDSL (G993.2)
       61  ZONE_TEST                        VDSL (G993.2)
       82  VDSL LINE PROFILE 82             VDSL (G993.2)
       88  VDSL LINE PROFILE 88             VDSL (G993.2)
      103  VDSL LINE PROFILE 103            VDSL (G993.2)
  ------------------------------------------------------------------------------
  Total: 5

检查创建的信道配置文件

MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:

  Command:
          display vdsl channel-profile
  ------------------------------------------------------------------------------
  Profile  Profile            MinDw    MaxDw    MinUp    MaxUp   Data Path
  Index    Name               Rate     Rate     Rate     Rate    Mode
  ------------------------------------------------------------------------------
       60  test_vdsl      128   100000      128   100000   Both
       61  ZONE_TEST      128   100000      128   100000   PTM
       99  VDSL CHANNEL PRO     128   100000      128   100000   PTM
           FILE 99
  ------------------------------------------------------------------------------
  Total: 3

注意:速率单元是Kbps。

检查创建的线路模板

MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:

  Command:
          display vdsl line-template
  ------------------------------------------------------------------------------
  Template  Template         Line Profile  Channel1       Channnel2
  Index     Name             Index         Profile Index  Profile Index
  ------------------------------------------------------------------------------
        12  ios_test                   10             11              -
        16  DT-17a                     18             18              -
        17  profile_17a                17             17              -
        18  aj_3M_US                   17              5              -
        60  VDSL LINE TEMPLA           60             60              -
            TE 60
        61  ZONE_TEST                  61             61              -
  ------------------------------------------------------------------------------
  Total: 6

检查DSLAM端口状态

对于此,您需要是在DSLAM的接口配置模式。

MA5600(config-if-vdsl-0/5)#display port state 0
  -----------------------------------------------------------------
  Port     Status        Loopback    Line Template   Alarm Template
  -----------------------------------------------------------------
     0     Activated     Disable                61                1
  -----------------------------------------------------------------

在CPE的验证

输入show controller vdsl 0 on命令CPE为了检查控制器状态。

/snip

C887VA-M#show controller vdsl 0
Controller VDSL 0 is UP

Daemon Status:           Up

                        XTU-R (DS)              XTU-C (US)
Chip Vendor ID:         'BDCM'                   'BDCM'
Chip Vendor Specific:   0x0000                   0x939B
Chip Vendor Country:    0xB500                   0xB500
Modem Vendor ID:        'CSCO'                   '    '
Modem Vendor Specific:  0x4602                   0x0000
Modem Vendor Country:   0xB500                   0x0000
Serial Number Near:    FTX162580HZ 887VA-M 15.2(4)M
Serial Number Far:
Modem Version Near:    15.2(4)M
Modem Version Far:     0x939b

Modem Status:            TC Sync (Showtime!)
DSL Config Mode:         AUTO
Trained Mode:            G.993.2 (VDSL2) Profile 12a
TC Mode:                 PTM

故障排除

目前没有针对此配置的故障排除信息。

相关信息



Document ID: 118642