交换机 : Cisco Catalyst 6500 系列交换机

在Catalyst 6800ia接入端口配置示例的QoS

2016 年 10 月 24 日 - 机器翻译
其他版本: PDFpdf | 英语 (2016 年 4 月 21 日) | 反馈

简介

本文描述如何配置,验证和排除故障在思科Catalyst 6800ia主机端口的服务质量(QoS)。6800ia Cisco IOS软件版本152.1.SY和稍后Catalyst 6800 parent虚拟交换系统的(VSS)主机端口支持QoS。

贡献用Shashank辛哈, Cisco TAC工程师。

先决条件

要求

本文档没有任何特定的要求。

使用的组件

本文档中的信息基于以下软件和硬件版本:

  • Cisco IOS软件版本152.1.SY
  • 思科Catalyst 6800 parent VSS

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始(默认)配置。如果您使用的是真实网络,请确保您已经了解所有命令的潜在影响。

背景信息

在Catalyst 6800ia的配置模式禁用,并且必须从parent执行6800ia主机端口的所有QoS配置。6800ia主机端口的QoS配置与策略映射。当应用对接口,此策略映射推送相关配置内部地对6800ia然后编程硬件队列。

6800ia主机端口有1p3q3t体系结构在transmit (TX)方向。在本文的所有配置示例仅适用对在6800ia的TX队列。

当没有时明确QoS配置在6800ia在默认状态建立接口,接口能看起来类似于此示例输出的6800ia主机:

6880-VSS#show run int gi101/1/0/1

interface GigabitEthernet101/1/0/1
 switchport
 switchport trunk allowed vlan 500
 switchport mode access
 switchport access vlan 500
 load-interval 30
end

6880-VSS#show queueing interface gi101/1/0/1
Interface GigabitEthernet101/1/0/1 queueing strategy:  Weighted Round-Robin

  Port QoS is disabled globally
  Queueing on Gi101/1/0/1: Tx Enabled Rx Disabled

Trust boundary disabled

  Trust state: trust DSCP
  Trust state in queueing: trust DSCP
  Default COS is 0
    Queueing Mode In Tx direction: mode-dscp
    Transmit queues [type = 1p3q3t]:
    Queue Id    Scheduling  Num of thresholds
    -----------------------------------------
       1         Priority            3
       2         WRR                 3
       3         WRR                 3
       4         WRR                 3

    WRR bandwidth ratios:  100[queue 2] 100[queue 3] 100[queue 4]   0[queue 5]
    queue-limit ratios:     15[Pri Queue]  25[queue 2]  40[queue 3]  20[queue 4]

    queue thresh dscp-map
    ---------------------------------------
    1     1      32 33 40 41 42 43 44 45 46 47
    1     2      
    1     3      
    2     1      16 17 18 19 20 21 22 23 26 27 28 29 30 31 34 35 36 37 38 39
    2     2      24
    2     3      48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
    3     1      25
    3     2      
    3     3      0 1 2 3 4 5 6 7
    4     1      8 9 11 13 15
    4     2      10 12 14
    4     3      

配置

配置示例1 :队列带宽

此示例显示您如何能配置6800ia TX队列的带宽:

  1. 配置类映射为了分类流量利益:
    class-map type lan-queuing match-any ltest
     match dscp 32
    class-map type lan-queuing match-any ltest1
     match dscp 24
    class-map type lan-queuing match-any ltest2
     match dscp default
  2. 分配优先级和带宽到配置的等级:
    policy-map type lan-queuing ltest
     class type lan-queuing ltest
        priority
     class type lan-queuing ltest1
        bandwidth remaining percent 30
     class type lan-queuing ltest2
        bandwidth remaining percent 20
     class class-default
  3. 应用策略映射对有问题的6800ia的接口:

    注意:当您适用于LAN队列策略映射6800ia堆叠的时一个端口,传播对所有端口的变化在堆叠上。

    6880-VSS#conf t
    6880-VSS(config)#int gi101/1/0/1
    6880-VSS(config-if)#service-policy type lan-queuing output ltest
    Propagating [attach] lan queueing policy "ltest" to Gi101/1/0/1 Gi101/1/0/2 Gi101/1/0/3
    Gi101/1/0/4 Gi101/1/0/5 Gi101/1/0/6 Gi101/1/0/7 Gi101/1/0/8 Gi101/1/0/9 Gi101/1/0/10
    Gi101/1/0/12 Gi101/1/0/13 Gi101/1/0/14 Gi101/1/0/15 Gi101/1/0/16 Gi101/1/0/17
    Gi101/1/0/18 Gi101/1/0/19 Gi101/1/0/20 Gi101/1/0/21 Gi101/1/0/22 Gi101/1/0/23
    Gi101/1/0/24 Gi101/1/0/25 Gi101/1/0/26 Gi101/1/0/27 Gi101/1/0/28 Gi101/1/0/29
    Gi101/1/0/30 Gi101/1/0/31 Gi101/1/0/32 Gi101/1/0/33 Gi101/1/0/34 Gi101/1/0/35
    Gi101/1/0/36 Gi101/1/0/37 Gi101/1/0/38 Gi101/1/0/39 Gi101/1/0/40 Gi101/1/0/41
    Gi101/1/0/42 Gi101/1/0/43 Gi101/1/0/44 Gi101/1/0/45 Gi101/1/0/46 Gi101/1/0/47 Gi101/1/0/48

    Propagating [attach] lan queueing policy "ltest" to Gi101/2/0/1 Gi101/2/0/2
    Gi101/2/0/3 Gi101/2/0/4 Gi101/2/0/5 Gi101/2/0/6 Gi101/2/0/7 Gi101/2/0/8
    Gi101/2/0/9 Gi101/2/0/10 Gi101/2/0/11 Gi101/2/0/12 Gi101/2/0/13 Gi101/2/0/14
    Gi101/2/0/15 Gi101/2/0/16 Gi101/2/0/17 Gi101/2/0/18 Gi101/2/0/19 Gi101/2/0/20
    Gi101/2/0/21 Gi101/2/0/22 Gi101/2/0/23 Gi101/2/0/24 Gi101/2/0/25 Gi101/2/0/26
    Gi101/2/0/27 Gi101/2/0/28 Gi101/2/0/29 Gi101/2/0/30 Gi101/2/0/31 Gi101/2/0/32
    Gi101/2/0/33 Gi101/2/0/34 Gi101/2/0/35 Gi101/2/0/36 Gi101/2/0/37 Gi101/2/0/38
    Gi101/2/0/39 Gi101/2/0/40 Gi101/2/0/41 Gi101/2/0/42 Gi101/2/0/43 Gi101/2/0/44
    Gi101/2/0/45 Gi101/2/0/46 Gi101/2/0/47 Gi101/2/0/48

    Propagating [attach] lan queueing policy "ltest" to Gi101/3/0/1 Gi101/3/0/2
    Gi101/3/0/3 Gi101/3/0/4 Gi101/3/0/5 Gi101/3/0/6 Gi101/3/0/7 Gi101/3/0/8
    Gi101/3/0/9 Gi101/3/0/10 Gi101/3/0/11 Gi101/3/0/12 Gi101/3/0/13 Gi101/3/0/14
    Gi101/3/0/15 Gi101/3/0/16 Gi101/3/0/17 Gi101/3/0/18 Gi101/3/0/19 Gi101/3/0/20
    Gi101/3/0/21 Gi101/3/0/22 Gi101/3/0/23 Gi101/3/0/24 Gi101/3/0/25 Gi101/3/0/26
    Gi101/3/0/27 Gi101/3/0/28 Gi101/3/0/29 Gi101/3/0/30 Gi101/3/0/31 Gi101/3/0/32
    Gi101/3/0/33 Gi101/3/0/34 Gi101/3/0/35 Gi101/3/0/36 Gi101/3/0/37 Gi101/3/0/38
    Gi101/3/0/39 Gi101/3/0/40 Gi101/3/0/41 Gi101/3/0/42 Gi101/3/0/43 Gi101/3/0/44
    Gi101/3/0/45 Gi101/3/0/46 Gi101/3/0/47 Gi101/3/0/48

    Propagating [attach] lan queueing policy "ltest" to Gi101/4/0/1 Gi101/4/0/2
    Gi101/4/0/3 Gi101/4/0/4 Gi101/4/0/5 Gi101/4/0/6 Gi101/4/0/7 Gi101/4/0/8
    Gi101/4/0/9 Gi101/4/0/10 Gi101/4/0/11 Gi101/4/0/12 Gi101/4/0/13 Gi101/4/0/14
    Gi101/4/0/15 Gi101/4/0/16 Gi101/4/0/17 Gi101/4/0/18 Gi101/4/0/19 Gi101/4/0/20
    Gi101/4/0/21 Gi101/4/0/22 Gi101/4/0/23 Gi101/4/0/24 Gi101/4/0/25 Gi101/4/0/26
    Gi101/4/0/27 Gi101/4/0/28 Gi101/4/0/29 Gi101/4/0/30 Gi101/4/0/31 Gi101/4/0/32
    Gi101/4/0/33 Gi101/4/0/34 Gi101/4/0/35 Gi101/4/0/36 Gi101/4/0/37 Gi101/4/0/38
    Gi101/4/0/39 Gi101/4/0/40 Gi101/4/0/41 Gi101/4/0/42 Gi101/4/0/43 Gi101/4/0/44
    Gi101/4/0/45 Gi101/4/0/46 Gi101/4/0/47 Gi101/4/0/48
    6880-VSS(config-if)#
    6880-VSS(config-if)#end
  4. 验证策略映射应用:
    6880-VSS#show run int gi101/1/0/1

    interface GigabitEthernet101/1/0/1
     switchport
     switchport trunk allowed vlan 500
     switchport mode access
     switchport access vlan 500
     load-interval 30
     service-policy type lan-queuing output ltest
    end
  5. 检查类映射对队列映射、带宽和缓冲分配和队列对差分服务代码点映射:
    6880-VSS#show queueing int gi101/1/0/1
    Interface GigabitEthernet101/1/0/1 queueing strategy:  Weighted Round-Robin

      Port QoS is disabled globally
      Queueing on Gi101/1/0/1: Tx Enabled Rx Disabled

    Trust boundary disabled

      Trust state: trust DSCP
      Trust state in queueing: trust DSCP
      Default COS is 0
        Class-map to Queue in Tx direction
        Class-map           Queue Id
        ----------------------------
        ltest                     1
        ltest1                    4
        ltest2                    3
        class-default             2


        Queueing Mode In Tx direction: mode-dscp
        Transmit queues [type = 1p3q3t]:
        Queue Id    Scheduling  Num of thresholds
        -----------------------------------------
           1         Priority            3
           2         WRR                 3
           3         WRR                 3
           4         WRR                 3

        WRR bandwidth ratios:   50[queue 2]  20[queue 3]  30[queue 4]
        queue-limit ratios:     15[Pri Queue] 100[queue 2] 100[queue 3] 100[queue 4]

        queue thresh dscp-map
        ---------------------------------------
        1     1      32
        1     2      
        1     3      
        2     1      1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
    23 25 26 27 28 29 30 31 33 34 35 36 37 38 39 40 41 42 43
    44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
        2     2      
        2     3      
        3     1      0
        3     2      
        3     3      
        4     1      24
        4     2      
        4     3      
  6. 将缓冲区和带宽分配仔细检查从6800ia :

    注意:如果不指定部分组的缓冲区重要性,默认情况下采取100%。

    Queue1 :15/[15+100+100+100] = 4

    队列2 :100/[15+100+100+100] | 31

    重要性为其他队列也派生。

    6880-VSS#remote command fex 101 show mls qos int gi1/0/1 buffer

    GigabitEthernet1/0/1
    The port is mapped to qset : 1
    The allocations between the queues are : 4 31 31 34  


    6880-VSS#remote command fex 101 show mls qos int gi1/0/1 queueing

    GigabitEthernet1/0/1
    Egress Priority Queue : enabled
    Shaped queue weights (absolute) :  0 0 0 0
    Shared queue weights  :  0 127 51 76
    The port bandwidth limit : 100  (Operational Bandwidth:100.0)
    The port is mapped to qset : 1
  7. 请验证,如果感兴趣流量在各自队列排队,并且,如果有任何丢包:
    6880-VSS#remote command fex 101 show mls qos int gi1/0/1 statistic

    GigabitEthernet1/0/1 (All statistics are in packets)

      dscp: incoming  
    -------------------------------

      0 -  4 :           0            0            0            0            0  
      5 -  9 :           0            0            0            0            0  
     10 - 14 :           0            0            0            0            0  
     15 - 19 :           0            0            0            0            0  
     20 - 24 :           0            0            0            0            0  
     25 - 29 :           0            0            0            0            0  
     30 - 34 :           0            0            0            0            0  
     35 - 39 :           0            0            0            0            0  
     40 - 44 :           0            0            0            0            0  
     45 - 49 :           0            0            0           13            0  
     50 - 54 :           0            0            0            0            0  
     55 - 59 :           0            0            0            0            0  
     60 - 64 :           0            0            0            0  
      dscp: outgoing
    -------------------------------

      0 -  4 :           0            0            0            0            0  
      5 -  9 :           0            0            0            0            0  
     10 - 14 :           0            0            0            0            0  
     15 - 19 :           0            0            0            0            0  
     20 - 24 :           0            0            0            0      9118500  
     25 - 29 :           0            0            0            0            0  
     30 - 34 :           0            0       516236            0            0  
     35 - 39 :           0            0            0            0            0  
     40 - 44 :           0            0            0            0            0  
     45 - 49 :           0            0            0           20            0  
     50 - 54 :           0            0            0            0            0  
     55 - 59 :           0            0            0            0            0  
     60 - 64 :           0            0            0            0  
      cos: incoming  
    -------------------------------

      0 -  4 :         106            0            0            0            0  
      5 -  7 :           0            0            0  
      cos: outgoing
    -------------------------------

      0 -  4 :          41            0            0      9118505       516236  
      5 -  7 :           0            0            0  
      output queues enqueued:
     queue:    threshold1   threshold2   threshold3
    -----------------------------------------------
     queue 0:      516255          35           5
     queue 1:          12           0           0
     queue 2:           0           0           0
     queue 3:     9118520           0           0

      output queues dropped:
     queue:    threshold1   threshold2   threshold3
    -----------------------------------------------
     queue 0:      0           0           0
     queue 1:           0           0           0
     queue 2:           0           0           0
     queue 3:       49823            0           0

    Policer: Inprofile:            0 OutofProfile:            0

配置示例2 :带宽和缓冲区

此示例显示您如何能配置带宽和缓冲区6800ia TX队列的:

  1. 在示例创建的策略映射,当此示例显示, 1,您能指定队列缓冲区分配:

    注意:如果不指定部分组的缓冲区重要性,默认情况下采取100%。

    policy-map type lan-queuing ltest
     class type lan-queuing ltest
        priority
        queue-buffers ratio 15

     class type lan-queuing ltest1
       bandwidth remaining percent 30
        queue-buffers ratio 30

     class type lan-queuing ltest2
        bandwidth remaining percent 20
        queue-buffers ratio 40

     class class-default
        queue-buffer ratio 15
  2. 检查类映射对队列映射、带宽和缓冲分配和队列对DSCP映射:
    6880-VSS#sh queueing int gi101/1/0/1    
    Interface GigabitEthernet101/1/0/1 queueing strategy:  Weighted Round-Robin

      Port QoS is disabled globally
      Queueing on Gi101/1/0/1: Tx Enabled Rx Disabled

    Trust boundary disabled

      Trust state: trust DSCP
      Trust state in queueing: trust DSCP
      Default COS is 0
        Class-map to Queue in Tx direction
        Class-map           Queue Id
        ----------------------------
        ltest                     1
        ltest1                    4
        ltest2                    3
        class-default             2


        Queueing Mode In Tx direction: mode-dscp
        Transmit queues [type = 1p3q3t]:
        Queue Id    Scheduling  Num of thresholds
        -----------------------------------------
           1         Priority            3
           2         WRR                 3
           3         WRR                 3
           4         WRR                 3

        WRR bandwidth ratios:   50[queue 2]  20[queue 3]  30[queue 4]
        queue-limit ratios:     15[Pri Queue]  15[queue 2]  40[queue 3]  30[queue 4]


        queue thresh dscp-map
        ---------------------------------------
        1     1      32
        1     2      
        1     3      
        2     1      1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
    22 23 25 26 27 28 29 30 31 33 34 35 36 37 38 39 40 41
    42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
        2     2      
        2     3      
        3     1      0
        3     2      
        3     3      
        4     1      24
        4     2      
        4     3      
  3. 将缓冲区和带宽分配仔细检查从6800ia :
    6880-VSS#remote command fex 101 sh mls qos int gi1/0/1 queueing

    GigabitEthernet1/0/1
    Egress Priority Queue : enabled
    Shaped queue weights (absolute) :  0 0 0 0
    Shared queue weights  :  0 127 51 76
    The port bandwidth limit : 100  (Operational Bandwidth:100.0)
    The port is mapped to qset : 1


    6880-VSS#remote command fex 101 sh mls qos int gi1/0/1 buffers

    GigabitEthernet1/0/1
    The port is mapped to qset : 1
    The allocations between the queues are : 15 15 40 30  
  4. 请验证,如果感兴趣流量在各自队列排队,并且,如果有任何丢包:
    6880-VSS#remote command fex 101 sh mls qos int gi1/0/1 statistic

    GigabitEthernet1/0/1 (All statistics are in packets)

      dscp: incoming  
    -------------------------------

      0 -  4 :           0            0            0            0            0  
      5 -  9 :           0            0            0            0            0  
     10 - 14 :           0            0            0            0            0  
     15 - 19 :           0            0            0            0            0  
     20 - 24 :           0            0            0            0            0  
     25 - 29 :           0            0            0            0            0  
     30 - 34 :           0            0            0            0            0  
     35 - 39 :           0            0            0            0            0  
     40 - 44 :           0            0            0            0            0  
     45 - 49 :           0            0            0          491            0  
     50 - 54 :           0            0            0            0            0  
     55 - 59 :           0            0            0            0            0  
     60 - 64 :           0            0            0            0  
      dscp: outgoing
    -------------------------------

      0 -  4 :           0            0            0            0            0  
      5 -  9 :           0            0            0            0            0  
     10 - 14 :           0            0            0            0            0  
     15 - 19 :           0            0            0            0            0  
     20 - 24 :           0            0            0            0    57864687  
     25 - 29 :           0            0            0            0            0  
     30 - 34 :           0            0     29364400            0            0  
     35 - 39 :           0            0            0            0            0  
     40 - 44 :           0            0            0            0            0  
     45 - 49 :           0            0            0          775            0  
     50 - 54 :           0            0            0            0            0  
     55 - 59 :           0            0            0            0            0  
     60 - 64 :           0            0            0            0  
      cos: incoming  
    -------------------------------

      0 -  4 :        5323            0            0            0            0  
      5 -  7 :           0            0            0  
      cos: outgoing
    -------------------------------

      0 -  4 :        1718            0            0    57864691     29364400  
      5 -  7 :           0            0            0  
      output queues enqueued:
     queue:    threshold1   threshold2   threshold3
    -----------------------------------------------
     queue 0:    29365402        1883           5
     queue 1:         793    98           0
     queue 2:           0           0           0
     queue 3:   530554174           0           0

      output queues dropped:
     queue:    threshold1   threshold2   threshold3
    -----------------------------------------------
     queue 0:    0          10           0
     queue 1:           1       24093           0
     queue 2:           0           0           0
     queue 3:     2309351           0           0

    Policer: Inprofile:            0 OutofProfile:            0

验证

当前没有可用于此配置的验证过程。

故障排除

本部分提供的信息可用于对配置进行故障排除。

命令输出解释程序工具仅限注册用户)支持某些 show 命令。请使用Output Interpreter Tool为了查看show命令输出分析。

注意:使用 debug 命令之前,请参阅有关 Debug 命令的重要信息

 

  1. QoS管理器的Enable (event)调试从6800ia CLI。保证日志重定向缓冲,并且操作日志缓冲区设置为大量:
    6880-VSS#attach fex 101
    Attach FEX:101 ip:192.168.1.101
    Trying 192.168.1.101 ... Open
    ????????FEX-101>en
    Password: cisco
    FEX-101#
    FEX-101#debug platform qos-manager all
    QM verbose debugging is on
    QM cops debugging is on
    QM events debugging is on
    QM Statistics debugging is on
    FEX-101#exit
    [Connection to 192.168.1.101 closed by foreign host]
  2. 配置策略映射为了触发调试:
    6880-VSS#conf t
    6880-VSS(config)#int gi101/1/0/1
    6880-VSS(config-if)# service-policy type lan-queuing output ltest  
    Propagating [attach] lan queueing policy "ltest" to Gi101/1/0/1
    Gi101/1/0/2 Gi101/1/0/3 Gi101/1/0/4 Gi101/1/0/5 Gi101/1/0/6 Gi101/1/0/7 Gi101/1/0/8
    Gi101/1/0/9 Gi101/1/0/10 Gi101/1/0/12 Gi101/1/0/13 Gi101/1/0/14 Gi101/1/0/15 Gi101/1/0/16
    <snip>
    6880-VSS(config-if)#end
  3. 检查注册结构扩展器(FEX)为了检查调试:
    6880-VSS#remote command fex 101 show log
    <snip>
    May 20 06:43:18.208: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
    ****Setting Priority Queue (FEX-101)


    May 20 06:43:18.208: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
    subopcode=2 startport=0 endport=0 size=4 (FEX-101)
    May 20 06:43:18.208: HQM: hulc_f
    _fex_qos_priority_handler:QueueNum=1 PriorityQueue=1 queuetype=2 thresholdsnum=3 (FEX-101)
    May 20 06:43:18.212: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
    idb=GigabitEthernet1/0/1 (FEX-101)
    May 20 06:43:18.212: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
    idb=GigabitEthernet1/0/2 (FEX-101)
    May 20 06:43:18.212: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
    idb=GigabitEthernet1/0/3 (FEX-101)
    <snip>
    hulc_fex_qos_srr_weight_setting:****Setting weight for queues**** (FEX-101)
    May 20 06:43:18.232: HQM: hulc_fex_qos_srr_weight_setting: hulc_fex_qos_srr_weight_setting:
    subopcode=2 startport=0 endport=0 size=4 (FEX-101)
    May 20 06:43:18.232: HQM: hulc_fex_qos_srr_weight_setting: hulc_fex_qos_srr_weight_setting:
    QueueNum=1 RRType=0 WeightRelative=0 WeightAbsolute=0 (FEX-101)
     20 06:43:18.232: HQM: hulc_fex_qos_srr_weight_setting: hulc_fex_qos_srr_weight_setting:
    ratio is 0 for queue 1 (FEX-101)
    May 20 06:43:18.232: HQM: hulc_fex_qos_srr_weight_setting: hulc_fex_qos_srr_weight_setting:
    QueueNum=2 RRType=0 WeightRelative=33 WeightAbsolute=0 (FEX-101)
    <snip>
    20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf: **Setting buffer for output queues** (FEX-101)
    May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf: hulc_fex_qos_buffer_conf:
    subopcode=2 startport=0 endport=0 size=4 (FEX-101)
    May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf: hulc_fex_qos_buffer_conf:
    queuenum=1 size=15 (FEX-101)
    May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf:
    hulc_fex_qos_buffer_conf: queuenum=2 size=25 (FEX-101)
    May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf:
    hulc_fex_qos_buffer_conf: queuenum=3 size=40 (FEX-101)
    May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf:
    hulc_fex_qos_buffer_conf: queuenum=4 size=20 (FEX-101)
    May 20 06:43:19.110: HQM: hqm
     20 06:43:19.113: HQM: s88g_qd_get_queue_threshold: s88g_qd_get_queue_threshold:
    max_limit = 3200, set to 350. (FEX-101)
    May 20 06:43:19.113: HQM: s88g_qd_get_queue_threshold: s88g_qd_get_queue_threshold:
    max_limit = 3200, set to 350. (FEX-101)
    <snip>
    hulc_fex_qos_qthresh_map:****Setting dscp to output queue map**** (FEX-101)
    May 20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map:
    subopcode=2 startport=0 endport=0 size=1 (FEX-101)
    May 20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map: DscpBma
     20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map
    dscp=32 iterator=0 (FEX-101)
    May 20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map
    dscp=33 iterator=1 (FEX-101)
    May 20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map
    dscp=40 iterator=2 (FEX-101)
    <snip>


Document ID: 119140