语音 : Digital CAS

T1 CAS 信令的配置与故障排除

2015 年 8 月 28 日 - 机器翻译
其他版本: PDFpdf | 英语 (2015 年 4 月 22 日) | 反馈


目录


简介

本文解释必要的配置实现T1随路信令(CAS)。

先决条件

要求

尝试进行此配置之前,请确保满足以下要求:

本文根据知道数字T1 CAS (夺位信号)如何在IOS网关工作。读本文了解CAS信令方法的多种类型。本文也起一个指南作用对于配置不同种类的CAS发信号。

在您实现发信号在Cisco AS5300路由器前的E1 R2,请检查保证思科IOS�软件您的版本是与在E1模块的Cisco VCWare兼容。如果版本是不兼容的,在语音卡的数字信号信号处理器(DSP)模块不会装载,并且语音信号处理不会发生。请参阅Cisco VCWare兼容性矩阵关于Cisco AS5300保证您的版本兼容。

一般,如果Cisco VCWare版本不是与Cisco IOS软件兼容,您能由输入show vfc slot_number interface命令看到此如显示此处:

5300#show vfc 1 interface
Rx: in ptr 18, outptr 0
Tx: in ptr 14  outptr  14
0 in hw queue, 0 queue head , 0 queue tail
Hardware is VFC out-of-band channel
Interface : state RESET DSP instance (0x61048284)
dsp_number 0, Channel ID 0
TX outstanding 0, max TX outstanding 0
Received 18 packets, 1087 bytes, 0 giant packets
0 drops, 0 no buffers, 0 input errors
121 bytes output, 14 frames output
0 bounce errors 0

DSP module 1 is not installed
DSP module 2 is not installed
DSP module 3 is not installed
DSP module 4 is not installed
DSP module 5 is not installed

在以上输出, “DSP模块号不是安装的”语句显示版本为该模块号是不兼容的。安排DSP的模块的示例正确Cisco VCWare版本装载显示此处:

5300#show vfc 1 interface
Rx: in ptr 24, outptr 0
TX: in ptr 15  outptr  15
0 in hw queue, 0 queue head , 0 queue tail
Hardware is VFC out-of-band channel
Interface : state RESET DSP instance (0x618C6088)
dsp_number 0, Channel ID 0
TX outstanding 0, max TX outstanding 0
Received 283288 packets, 15864278 bytes, 0 giant packets
0 drops, 0 no buffers, 0 input errors
1416459 bytes output,  141647 frames output
0 bounce errors 0

Slot 1, DSPM 1 (C542), DSP 1, Channel 1
State RESET, DSP instance (0x61914BDC)
TX outstanding 0, max TX outstanding 8
Received 0 packets, 0 bytes, 0 giant packets
0 drops, 0 no buffers, 0 input errors
0 bytes output,  0 frames output
0 bounce errors 0

Slot 1, DSPM 1 (C542), DSP 2, Channel 1
State RESET, DSP instance (0x6191510C)
TX outstanding 0, max TX outstanding 8
Received 0 packets, 0 bytes, 0 giant packets
0 drops, 0 no buffers, 0 input errors
0 bytes output,  0 frames output
0 bounce errors 0

要检查已安装Cisco VCWare版本,请输入show vfc slot_number version vcware命令如显示此处:

5300#show vfc 1 version vcware
Voice Feature Card in Slot 1:
VCware Version : 4.10
ROM Monitor Version : 1.2
DSPware Version :
Technology :  C542

注意: 确保Cisco VCWare技术版本(c549或c542)匹配已安装语音功能卡DSP技术(DSPM-542 :单密度语音支持或者DSPM-549 :高密度语音支持)。

使用的组件

本文档中的信息基于以下软件和硬件版本:

  • Cisco AS5300路由器(所有版本)

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始(默认)配置。如果您使用的是真实网络,请确保您已经了解所有命令的潜在影响。

规则

有关文档规则的详细信息,请参阅 Cisco 技术提示规则

配置

本部分提供有关如何配置本文档所述功能的信息。

注意: 有关本文档所用命令的详细信息,请使用命令查找工具仅限注册用户)。

配置

要运行发信号在Cisco 2600/3600系列路由器的CAS,高密度语音网络模块(NM-HDV)要求。

ds0-group命令(或cas组,根据Cisco IOS版本)在T1控制器需要定义(Cisco As5xxx和2600/3600路由器)。

使用此步骤配置CAS :

  1. 设置T1控制器连接对专用自动小交换机(PBX)或交换机。保证T1的成帧和线性编码适当地设置。

    • T1帧:ESF或SF

    • T1线性编码:B8ZS或AMI

    • T1 clock source :内部或线路

    注意: 记住不同的PBX有在时钟源的不同的需求。

  2. 请使用此指令序列定义您的在As5xxx平台的线路信令:

    5300(config)#controller T1 0
    
    5300(config-controller)#
    ds0-group 1 timeslots 1-24 type ?
    
    e&m-fgb              E & M Type II FGB
    e&m-fgd              E & M Type II FGD
    e&m-immediate-start  E & M Immediate Start
    fgd-eana             FGD Exchange Access North American
    fgd-os               FGD Operator Services
    fxs-ground-start     FXS Ground Start
    fxs-loop-start       FXS Loop Start
    none                 Null Signaling for External Call Control
    r1-itu               R1 ITU
    sas-ground-start     SAS Ground Start
    sas-loop-start       SAS Loop Start
    <cr>

    注意: 如果要收集关于T1控制器的拨号号码识别服务(DNIS)信息,您在接入服务器必须手工配置它。要收集双音多频E&m-fgb的DNIS在控制器T1配置下,请使用ds0-group 0时隙1-24类型e&m-fgb dtmf dnis命令。要收集E&m-fgb的多频的(MF) DNIS,请使用dnis命令ds0-group 0时隙1-24类型的e&m-fgb mf

  3. 请使用此指令序列定义您的在Cisco2600/3600平台的线路信令:

    3600(config)#controller T1 0
    3600(config-controller)# 
    ds0-group 1 timeslots 1-24 type ? 
    
    e&m-delay-dial       E & M Delay Dial
    e&m-fgd 			 E & M Type II FGD
    e&m-immediate-start  E & M Immediate Start
    e&m-wink-start       E & M Wink Start
    ext-sig              External Signaling
    fgd-eana             FGD-EANA BOC side
    fxo-ground-start     FXO Ground Start
    fxo-loop-start       FXO Loop Start
    fxs-ground-start     FXS Ground Start
    fxs-loop-start       FXS Loop Start
    none                 Null Signaling for External Call Control
    <cr>

    使用Cisco IOS软件版本11.3,指令序列如下。

    peggy(config)#controller T1 0
    
    peggy(config-controller)#cas-group 1 timeslot 1-15 type ?
    
    ...

    注意: 如果从Cisco IOS软件版本11.3升级到版本12.0, new命令将自动地取代一个。

本文档使用以下配置:

为E&M-FGD DTMF DNIS配置的Cisco 5300
hostname 5300-fg-d

!

controller T1 0

 clock source line primary

 ds0-group 1 timeslots 1-24 type e&m-fgd dtmf dnis



!--- With this configuration we will use DTMF and
!--- request the DNIS information.


!

voice-port 0:1

!

dial-peer voice 123 pots

 destination-pattern 123

 direct-inward-dial 
 
!--- This will only work if the DNIS information is recieved.


 port 0:1

 prefix 123


!

dial-peer voice 567 voip

 destination-pattern 567

 session target ipv4:2.0.0.2

!

为E&M-FGB配置的Cisco 5300
hostname 5300-fg-b
!

controller T1 0

 clock source line primary

 ds0-group 1 timeslots 1-24 type e&m-fgb

!

voice-port 0:1

!
dial-peer voice 123 pots

 destination-pattern 123

 port 0:1

 prefix 123

!

dial-peer voice 567 voip

 destination-pattern 567

 session target ipv4:2.0.0.2

!

为E&M FGB配置的Cisco3600 (wink-start)
hostname 3600-fg-b
!

controller T1 1/0

 clock source line primary

 ds0-group 1 timeslots 1-24 type e&m-wink-start

!

voice-port 1/0:1

!
dial-peer voice 123 pots

 destination-pattern 123

 port 1/0:1

 prefix 123

!

dial-peer voice 567 voip

 destination-pattern 567

 session target ipv4:2.0.0.2

验证

当前没有可用于此配置的验证过程。

故障排除

本部分提供的信息可用于对配置进行故障排除。

故障排除步骤

请按照以下说明排除配置故障。参考用cas-custom命令定制E1 R2关于故障排除的更多信息。

  1. 验证T1控制器0是UP。如果它发生故障,请检查帧,线性编码,时钟源,警报,替换电缆,重新安装卡,等等等等。

  2. 如果使用Cisco AS5300,请检查DSP用show vfc slot number interface命令正确地安装。

  3. 对于FGD中继请配置在普通旧式电话服务对等体的直接拨入(DID),因此接收的数字用于选择流出对等体。

    注意: 在Cisco AS5300上您将需要安排“DNIS”选项配置请求DNIS。

  4. 打开在以下部分显示的某些调试指令并且学习输出

  5. 检查路由器和PBX之间的通信或者交换。

    • 线路被占用?

    • 路由器是否接收/发送位?

    • 发现侧清除呼叫。

    • 若可能,请使用最新的Cisco IOS软件版本可用在Cisco.com。

确定您的在思科As5xxx路由器的信令

可以是困难确定什么类型的信令您有通过查看路由器的调试。然而,做一个好猜测至于是可能的什么信令应该是。以下调试是相当可靠(特别是当所有信道空闲)时在确定信令种类。推荐您通过这些调试首先验证您的信令,因为他们能发现最普通和not-so-obvious设置的错误。照常,练习小心,当启用调试在路由器时。推荐您不启用调试,除非熟悉其功能。注意不是所有的调试为每个网络接入服务器(NAS)平台是可用的。

故障排除命令

命令输出解释程序仅限注册用户)(OIT) 支持某些 show 命令。使用 OIT 可查看对 show 命令输出的分析。

注意: 使用 debug 命令之前,请参阅有关 Debug 命令的重要信息

  • debug serial interface —显示关于串行连接故障的信息。

  • show controller t1 —显示控制器状态特定到控制器硬件。

  • debug cas —在思科As5xxx平台的线路信令。

  • debug vpm signal —在思科26xx/36xx平台的线路信令。

  • 全的debug vtsp启用输出所有消息(位)被交换在PBX和路由器之间。

bosshog#debug serial interface

!--- This enables the output below.

Serial network interface debugging is on

bosshog#show controller t1
T1 0 is up.
 No alarms detected.
 Version info of slot 0:  HW: 2, Firmware: 16, PLD Rev: 0
 Manufacture Cookie Info:
 EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x42,
 Board Hardware Version 1.0, Item Number 73-2217-4,
 Board Revision A0, Serial Number 07389920,
 PLD/ISP Version 0.0, Manufacture Date 3-Jan-1998.
 Framing is ESF, Line Code is B8ZS, Clock Source is Line Primary.
  Data in current interval (6 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
 Robbed bit signals state:
        timeslots     rxA rxB rxC rxD         txA txB txC txD

        1                0   0   0   0           0   0   0   0
        2                0   0   0   0           0   0   0   0
        <snip>
        23              0   0   0   0           0   0   0   0
        24              0   0   0   0           0   0   0   0


!--- Looking at the above signals, we are receiving all 0s from the switch.
!--- This looks like some form of E&M Signaling.
!--- We can determine the following when the line is idle.


    timeslots     rxA rxB rxC rxD         txA txB txC txD
    1                0   0   0   0           0   0   0   0 
    
!--- Looks like an E&M variant.

    2                0   1   0   1           0   1   0   1 
    
!--- Looks like fxs-loop-start.

    3                1   1   1   1           0   1   0   1 
    
!--- Looks like fxs-ground-start.

下面的输出是为在Cisco AS5300的E&M FGB。

5300-fg-b#show debug
CAS:

 Channel Associated Signaling debugging is on

5300-fg-b#

!--- Incoming call to router.

*May 28 12:40:35.376: from Trunk(0): (1/0): Rx LOOP_CLOSURE (ABCD=1111)

!--- Switch is off hook.
!--- Send wink back to the switch. Note we transition from a on/off/on hook state.

*May 28 12:40:35.600: from Trunk(0): (1/0): Tx LOOP_CLOSURE (ABCD=1111)

!--- Sending Wink back. Off hook.

*May 28 12:40:35.800: from Trunk(0): (1/0): Tx LOOP_OPEN (ABCD=0000)

!--- End of wink ~200 ms duration.  On hook.

5300-fg-b#
5300-fg-b#

!--- The call is now in an alerting state waiting for a connect.
!--- Router goes off hook. Call is connected.

*May 28 12:40:37.352: from Trunk(0): (1/0): Tx LOOP_CLOSURE (ABCD=1111)

!--- Router has gone off hook. Send a connect.

5300-fg-b#
5300-fg-b#
5300-fg-b#

!--- At this point, the call is torn down in the direction of the PBX.

*May 28 12:40:42.608: from Trunk(0): (1/0): Tx LOOP_OPEN (ABCD=0000)

!--- Router disconnects call on hook.

*May 28 12:40:42.940: from Trunk(0): (1/0): Rx LOOP_OPEN (ABCD=0000)

!--- Switch terminates upon receipt on hook.

此示例是为在Cisco3600的流出的E&M FGB。

3600-fg-b#show debug

Voice Port Module signaling debugging is on
3600-fg-b#

!--- Outgoing call from router.

*Mar  3 04:01:35.167: htsp_process_event: [2/1:1(1), EM_ONHOOK, E_HTSP_SETUP_REQ
]em_onhook_setup 

!--- On hook state.

*Mar  3 04:01:35.167: em_offhook (0)[recEive and transMit2/1:1(1)] set signal st
ate = 0x8
*Mar  3 04:01:35.167: htsp_process_event: [2/1:1(1), EM_BRANCH, EM_EVENT_WINK]
*Mar  3 04:01:35.167: em_start_timer: 550 ms
*Mar  3 04:01:35.167: htsp_timer - 550 msec
*Mar  3 04:01:35.415: htsp_process_event: [2/1:1(1), EM_WAIT_WINKUP, E_DSP_SIG_1
100]em_wink_offhook 

!--- Router sends off hook.

*Mar  3 04:01:35.415: em_stop_timers
*Mar  3 04:01:35.415: htsp_timer_stop
*Mar  3 04:01:35.415: em_start_timer: 1200 ms
*Mar  3 04:01:35.415: htsp_timer - 1200 msec
*Mar  3 04:01:35.619: htsp_process_event: [2/1:1(1), EM_WAIT_WINKDOWN, E_DSP_SIG
_0000]em_wink_onhook 

!--- Router sends on hook.

*Mar  3 04:01:35.623: em_stop_timers
*Mar  3 04:01:35.623: htsp_timer_stop htsp_wink_ind
*Mar  3 04:01:35.623: htsp_timer - 70 msec
*Mar  3 04:01:35.695: htsp_process_event: [2/1:1(1), EM_WAIT_DIALOUT_DELAY, E_HT
SP_EVENT_TIMER]em_imm_send_digits  em_send_digits  htsp_dial

!--- At this point we send the digits.

*Mar  3 04:01:36.507: htsp_process_event: [2/1:1(1), EM_WAIT_FOR_ANSWER, E_DSP_D
IALING_DONE]em_offhook_digit_done htsp_progress
*Mar  3 04:01:36.507: ===== state 0x630852C0

*Mar  3 04:01:37.035: htsp_process_event: [2/1:1(1), EM_WAIT_FOR_ANSWER, E_DSP_S
IG_1100]em_wait_answer_offhook

!--- Router is waiting for far end to connect.

*Mar  3 04:01:37.035: em_stop_timers
*Mar  3 04:01:37.035: htsp_timer_stop
*Mar  3 04:01:37.035: htsp_timer_stop2

此示例是为FXS回路开始在Cisco2600。

FXS Loop-start Signal Map
*Mar 1 01:55:51.091: Foreign Exchange Station 1/1:1(22) rx_signal_map:
0 F F F
5 F 5 F
F F F F
F F F F
*Mar 1 01:55:51.095: Foreign Exchange Station 1/1:1(22) tx_signal_map:
4 4 4 4
4 4 4 4
C C C C
C C C C


!--- FXS Loop-start incoming call.

*Mar 1 02:02:13.743: htsp_dsp_message: SEND/RESP_SIG_STATUS: state=0xC timestamp=26688 systime=733374
*Mar 1 02:02:13.743: [1/1:1(1), FXSLS_ONHOOK, E_DSP_SIG_1100] fxsls_onhook_offhook htsp_setup_ind
*Mar 1 02:02:13.751: [1/1:1(1), FXSLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
*Mar 1 02:02:14.871: [1/1:1(1), FXSLS_OFFHOOK, E_HTSP_PROCEEDING] htsp_alert_notify
*Mar 1 02:02:15.163: [1/1:1(1), FXSLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 02:02:15.607: [1/1:1(1), FXSLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 02:02:15.607: [1/1:1(1), FXSLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]


!--- Call is ringing now.
!--- Is answered below.

vdtl-2600-6d#htsp_connect: no_offhook 0
*Mar 1 02:02:26.239: [1/1:1(1), FXSLS_OFFHOOK, E_HTSP_CONNECT]
fxsls_offhook_connect[Foreign Exchange Station 1/1:1(1)] set signal state = 0x6


!--- Call is disconnected from T1 side below.

vdtl-2600-6d#  

!--- Near end disconnect (from T1 side).

vdtl-2600-6d#
*Mar 1 02:02:37.299: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x4 timestamp=50246 systime=735730
*Mar 1 02:02:37.299: [1/1:1(1), FXSLS_CONNECT, E_DSP_SIG_0100] fxsls_offhook_onhook
*Mar 1 02:02:37.299: htsp_timer - 600 msec
*Mar 1 02:02:37.899: [1/1:1(1), FXSLS_CONNECT,
E_HTSP_EVENT_TIMER] fxsls_connect_wait_release_req
*Mar 1 02:02:37.899: htsp_timer_stop htsp_release_req: cause 16, no_onhook 0
*Mar 1 02:02:37.919: [1/1:1(1), FXSLS_WAIT_RELEASE_REQ,
E_HTSP_RELEASE_REQ] fxsls_waitrls_req_rlshtsp_report_onhook_sig
*Mar 1 02:02:37.923: vnm_dsprm_close_cleanup


!--- FXS loop-start outgoing call.

*Mar 1 03:42:05.067: [1/1:1(2), FXSLS_ONHOOK, E_HTSP_SETUP_REQ]
fxsls_onhook_setup[Foreign Exchange Station 1/1:1(2)] set signal state = 0x0htsp_alert
*Mar 1 03:42:05.327: [1/1:1(2), FXSLS_WAIT_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH] fxsls_waitoff_voice
*Mar 1 03:42:05.763: [1/1:1(2), FXSLS_WAIT_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH] fxsls_waitoff_voice
*Mar 1 03:42:05.763: [1/1:1(2), FXSLS_WAIT_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH] fxsls_waitoff_voice

!--- Call is ringing now.
!--- Call is answered below.
*Mar 1 03:42:30.039: htsp_dsp_message:
SEND/RESP_SIG_STATUS: state=0x4 timestamp=14102 systime=1335004
*Mar 1 03:42:30.039: [1/1:1(1), FXSLS_ONHOOK, E_DSP_SIG_0100]
*Mar 1 03:42:30.087: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0xC timestamp=14144 systime=1335008
*Mar 1 03:42:30.087: [1/1:1(2), FXSLS_WAIT_OFFHOOK, E_DSP_SIG_1100]
fxsls_waitoff_offhook[Foreign Exchange Station 1/1:1(2)]
set signal state = 0x4[Foreign Exchange Station 1/1:1(2)]
set signal state = 0x6 htsp_dial


!--- Call is disconnected via VoIP side below.

vdtl-2600-6d#htsp_release_req: cause 16, no_onhook 0
*Mar 1 03:43:27.855: [1/1:1(2), FXSLS_CONNECT, E_HTSP_RELEASE_REQ] fxsls_connect_disc
*Mar 1 03:43:27.855: htsp_timer_stop [Foreign Exchange Station 1/1:1(2)]
set signal state = 0xC[Foreign Exchange Station 1/1:1(2)] set signal state = 0x4
*Mar 1 03:43:27.859: htsp_timer - 950 msec
*Mar 1 03:43:28.811: [1/1:1(2), FXSLS_CPC, E_HTSP_EVENT_TIMER] fxsls_cpc_timer
*Mar 1 03:43:28.811: htsp_timer - 30000 msec
*Mar 1 03:43:28.815: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0xC timestamp=8470 systime=1340881
*Mar 1 03:43:28.815: [1/1:1(2), FXSLS_WAIT_ONHOOK, E_DSP_SIG_1100]

此示例是为FXO回路开始在Cisco2600。

FXO Loop-start Channel Map
*Mar 1 03:48:30.055: Foreign Exchange Office 1/1:1(24) rx_signal_map:
F F F F
5 F F F
F F F F
F F F F[Foreign Exchange Office 1/1:1(24)] set signal state = 0x4
*Mar 1 03:48:30.055: Foreign Exchange Office 1/1:1(24) tx_signal_map:
0 0 4 4
4 4 4 4
C C C C
C C C C


!--- FXO loop-start incoming call.

*Mar 1 03:52:56.271: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x0 timestamp=50660 systime=1397627
*Mar 1 03:52:56.271: [1/1:1(1), FXOLS_ONHOOK, E_DSP_SIG_0000] fxols_onhook_ringing
*Mar 1 03:52:56.271: htsp_timer - 10000 msec
*Mar 1 03:52:58.267: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x4 timestamp=52658 systime=1397826
*Mar 1 03:52:58.271: [1/1:1(1), FXOLS_RINGING, E_DSP_SIG_0100]
*Mar 1 03:52:58.271: fxols_ringing_not
*Mar 1 03:52:58.271: htsp_timer_stop htsp_setup_ind
*Mar 1 03:52:58.275: [1/1:1(1), FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
*Mar 1 03:52:58.275: fxols_wait_setup_ack:
[Foreign Exchange Office 1/1:1(1)] set signal state = 0xC


!--- Call is ringing and is answered (dial tone).
!--- Entering destination for the call now.

*Mar 1 03:53:09.019: [1/1:1(1), FXOLS_PROCEEDING, E_HTSP_PROCEEDING] fxols_offhook_proc
*Mar 1 03:53:09.019: htsp_timer - 120000 msechtsp_alert_notify
*Mar 1 03:53:09.311: [1/1:1(1), FXOLS_PROCEEDING, E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 03:53:09.759: [1/1:1(1), FXOLS_PROCEEDING, E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 03:53:09.759: [1/1:1(1), FXOLS_PROCEEDING,
E_HTSP_VOICE_CUT_THROUGH] htsp_connect: no_offhook 0
*Mar 1 03:53:12.711: [1/1:1(1), FXOLS_PROCEEDING,
E_HTSP_CONNECT] fxols_offhook_connect
*Mar 1 03:53:12.711: htsp_timer_stop


!--- Call is disconnected via VoIP side.

vdtl-2600-6d#htsp_release_req: cause 16, no_onhook 0
*Mar 1 03:53:44.079: [1/1:1(1), FXOLS_CONNECT, E_HTSP_RELEASE_REQ]
fxols_offhook_release
*Mar 1 03:53:44.079: htsp_timer_stop [Foreign Exchange Office 1/1:1(1)]
set signal state = 0x4
*Mar 1 03:53:44.079: htsp_timer - 2000 msec
*Mar 1 03:53:44.079: vnm_dsprm_close_cleanup
*Mar 1 03:53:46.079: [1/1:1(1), FXOLS_GUARD_OUT,
E_HTSP_EVENT_TIMER] fxols_guard_out_timeout


!--- FXO loop-start outgoing call.

*Mar 1 03:50:47.099: [1/1:1(2), FXOLS_ONHOOK, E_HTSP_SETUP_REQ]
fxols_onhook_setup[Foreign Exchange Office 1/1:1(2)] set signal state = 0xC
*Mar 1 03:50:47.099: htsp_timer - 1300 msec
*Mar 1 03:50:48.399: [1/1:1(2), FXOLS_WAIT_DIAL_TONE,
E_HTSP_EVENT_TIMER] fxols_wait_dial_timer htsp_dial
*Mar 1 03:50:50.407: [1/1:1(2), FXOLS_WAIT_DIAL_DONE,
E_DSP_DIALING_DONE] fxols_wait_dial_done htsp_alert
*Mar 1 03:50:50.659: [1/1:1(2), FXOLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 03:50:50.695: [1/1:1(2), FXOLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 03:50:50.707: [1/1:1(2), FXOLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]


!--- Call is answered now.  Debugs shown because of lack of answer supervision.
!--- The next thing that happens is a VoIP side disconnect.

vdtl-2600-6d#htsp_release_req: cause 16, no_onhook 0
*Mar 1 03:51:06.483: [1/1:1(2), FXOLS_OFFHOOK,
E_HTSP_RELEASE_REQ] fxols_offhook_release
*Mar 1 03:51:06.483: htsp_timer_stop
[Foreign Exchange Office 1/1:1(2)] set signal state = 0x4
*Mar 1 03:51:06.483: htsp_timer - 2000 msec
*Mar 1 03:51:06.487: vnm_dsprm_close_cleanup
*Mar 1 03:51:08.483: [1/1:1(2), FXOLS_GUARD_OUT,
E_HTSP_EVENT_TIMER] fxols_guard_out_timeout

此示例是为在Cisco2600的FXS接地启动。


!--- FXS ground-start signal map.

*Mar 1 04:04:13.334: Foreign Exchange Station 1/1:1(16) rx_signal_map:
0 F F F
5 F 5 F
F F F F
F F F F
*Mar 1 04:04:13.338: Foreign Exchange Station 1/1:1(16) tx_signal_map:
0 0 0 0
4 4 4 4
8 8 8 8
C C C C


!--- FXS ground-start incoming call.

*Mar 1 04:05:22.650: %SYS-5-CONFIG_I: Configured from console by console
*Mar 1 04:05:26.982: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x0 timestamp=15488 systime=1472698
*Mar 1 04:05:26.982: [1/1:1(1), FXSGS_ONHOOK, E_DSP_SIG_0000]
fxsgs_onhook_ringgnd[Foreign Exchange Station 1/1:1(1)] set signal state = 0x4
*Mar 1 04:05:26.982: htsp_timer - 900 msec
*Mar 1 04:05:27.142: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0xC timestamp=15648 systime=1472714
*Mar 1 04:05:27.142: [1/1:1(1), FXSGS_WAIT_LOOPCLOSE,
E_DSP_SIG_1100] fxsgs_wait_loopclose
*Mar 1 04:05:27.142: htsp_timer_stop htsp_setup_ind
*Mar 1 04:05:27.150: [1/1:1(1), FXSGS_WAIT_SETUP_ACK,
E_HTSP_SETUP_ACK] fxsgs_wait_setup_rcv_ack[Foreign Exchange Station 1/1:1(1)]
set signal state = 0x4
*Mar 1 04:05:28.282: [1/1:1(1), FXSGS_OFFHOOK,
E_HTSP_PROCEEDING] htsp_alert_notify
*Mar 1 04:05:28.598: [1/1:1(1), FXSGS_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 04:05:28.626: [1/1:1(1), FXSGS_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 04:05:28.638: [1/1:1(1), FXSGS_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH]


!--- Call is ringing now.
!--- Call is answered below.

vdtl-2600-6d#htsp_connect: no_offhook 0
*Mar 1 04:05:35.262: [1/1:1(1), FXSGS_OFFHOOK, E_HTSP_CONNECT]
fxsgs_offhook_connect[Foreign Exchange Station 1/1:1(1)] set signal state = 0x6


!--- Call is disconnected via T1 side.

*Mar 1 04:05:42.822: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x4 timestamp=31328 systime=1474282
*Mar 1 04:05:42.822: [1/1:1(1), FXSGS_CONNECT, E_DSP_SIG_0100]
fxsgs_connect_onhookhtsp_release_req: cause 16, no_onhook 0
*Mar 1 04:05:42.850: [1/1:1(1), FXSGS_WAIT_RELEASE_REQ, E_HTSP_RELEASE_REQ]
fxsgs_wait_release_req_release[Foreign Exchange Station 1/1:1(1)] set signal state = 0xC
*Mar 1 04:05:42.850: vnm_dsprm_close_cleanup
*Mar 1 04:05:42.854: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x4 timestamp=8983 systime=1474285
*Mar 1 04:05:42.854: [1/1:1(1), FXSGS_ONHOOK, E_DSP_SIG_0100]
vdtl-2600-6d#


!--- FXS ground-start outgoing call.

*Mar 1 04:26:50.578: [1/1:1(1), FXSGS_ONHOOK, E_HTSP_SETUP_REQ]
fxsgs_onhook_setup[Foreign Exchange Station 1/1:1(1)] set signal state = 0x0htsp_alert
*Mar 1 04:26:50.834: [1/1:1(1), FXSGS_WAIT_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH] fxsgs_waitoff_voice
*Mar 1 04:26:51.282: [1/1:1(1), FXSGS_WAIT_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH] fxsgs_waitoff_voice
*Mar 1 04:26:51.282: [1/1:1(1), FXSGS_WAIT_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH] fxsgs_waitoff_voice


!--- Call rings and is then answered.

*Mar 1 04:27:02.234: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0xC timestamp=974 systime=1602223
*Mar 1 04:27:02.234: [1/1:1(1), FXSGS_WAIT_OFFHOOK, E_DSP_SIG_1100]
fxsgs_waitoff_offhook[Foreign Exchange Station 1/1:1(1)] set signal state = 0x4
*Mar 1 04:27:02.238: htsp_timer_stop [Foreign Exchange Station 1/1:1(1)]
 set signal state = 0x6


!--- Call is disconnected via VoIP side below.

vdtl-2600-6d#htsp_release_req: cause 16, no_onhook 0
*Mar 1 04:27:16.146: [1/1:1(1), FXSGS_CONNECT, E_HTSP_RELEASE_REQ]
fxsgs_connect_release[Foreign Exchange Station 1/1:1(1)] set signal state = 0xC
*Mar 1 04:27:16.190: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x0 timestamp=14928 systime=1603619
*Mar 1 04:27:16.194: [1/1:1(1), FXSGS_WAIT_ONHOOK, E_DSP_SIG_0000]

此示例是为在Cisco2600的FXO接地启动。


!--- FXO ground-start signal map.

*Mar 1 04:31:34.166: Foreign Exchange Office 1/1:1(1) rx_signal_map:
0 F F F
5 F F F
F F F F
F F F F
*Mar 1 04:31:34.166: Foreign Exchange Office 1/1:1(1) tx_signal_map:
0 0 0 0
4 4 4 4
8 8 8 8
C C C C


!--- FXO ground-start incoming call.

*Mar 1 04:35:26.194: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x0 timestamp=46190 systime=1652619
*Mar 1 04:35:26.194: [1/1:1(1), FXOGS_ONHOOK,
E_DSP_SIG_0000] fxogs_onhook_ringing
*Mar 1 04:35:26.194: htsp_timer_stop
*Mar 1 04:35:28.194: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x4 timestamp=48188 systime=1652819
*Mar 1 04:35:28.194: [1/1:1(1), FXOGS_RINGING, E_DSP_SIG_0100]
*Mar 1 04:35:28.194: fxogs_ringing_not:
*Mar 1 04:35:28.194: htsp_timer_stop htsp_setup_ind
*Mar 1 04:35:28.198: [1/1:1(1), FXOGS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
*Mar 1 04:35:28.202: fxogs_wait_setup_ack:
[Foreign Exchange Office 1/1:1(1)] set signal state = 0xC
vdtl-2600-6d#

!--- Call is answered.  Entering digits to route the call further.

vdtl-2600-6d#
*Mar 1 04:35:37.458: [1/1:1(1), FXOGS_OFFHOOK, E_HTSP_PROCEEDING] htsp_alert_notify
*Mar 1 04:35:37.750: [1/1:1(1), FXOGS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 04:35:37.782: [1/1:1(1), FXOGS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 04:35:37.798: [1/1:1(1), FXOGS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]


!--- VoIP side connected.

vdtl-2600-6d#htsp_connect: no_offhook 0
*Mar 1 04:35:43.350: [1/1:1(1), FXOGS_OFFHOOK, E_HTSP_CONNECT] fxogs_proc_voice


!--- Call disconnected from T1 side.

vdtl-2600-6d#
*Mar 1 04:36:02.890: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0xC timestamp=17354 systime=1656289
*Mar 1 04:36:02.894: [1/1:1(1), FXOGS_OFFHOOK,
E_DSP_SIG_1100] fxogs_offhook_disc
*Mar 1 04:36:02.894: htsp_timer_stop [Foreign Exchange Office 1/1:1(1)]
 set signal state = 0x4
*Mar 1 04:36:02.894: htsp_timer - 2000 msechtsp_release_req:
cause 16, no_onhook 0
*Mar 1 04:36:02.918: [1/1:1(1), FXOGS_GUARD_OUT,
E_HTSP_RELEASE_REQ] fxogs_onhook_release
*Mar 1 04:36:02.922: vnm_dsprm_close_cleanup
*Mar 1 04:36:04.894: [1/1:1(1), FXOGS_GUARD_OUT,
E_HTSP_EVENT_TIMER]


!--- FXO ground-start outgoing call.

*Mar 1 04:33:08.838: [1/1:1(1), FXOGS_ONHOOK, E_HTSP_SETUP_REQ]
fxogs_onhook_setup[Foreign Exchange Office 1/1:1(1)] set signal state = 0x0
*Mar 1 04:33:08.838: htsp_timer - 10000 msec
*Mar 1 04:33:09.214: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0x4 timestamp=40280 systime=1638921
*Mar 1 04:33:09.218: [1/1:1(1), FXOGS_WAIT_TIP_GROUND,
E_DSP_SIG_0100] fxogs_start_dial
*Mar 1 04:33:09.218: htsp_timer_stop
[Foreign Exchange Office 1/1:1(1)] set signal state = 0xC
*Mar 1 04:33:09.218: htsp_timer - 1000 msec
*Mar 1 04:33:10.218: [1/1:1(1), FXOGS_WAIT_DIAL_TONE,
E_HTSP_EVENT_TIMER] fxogs_wait_dial_timer htsp_dial
*Mar 1 04:33:12.226: [1/1:1(1), FXOGS_WAIT_DIAL_DONE, E_DSP_DIALING_DONE]
fxogs_wait_dial_donehtsp_connect: no_offhook 0htsp_alert
*Mar 1 04:33:12.226: [1/1:1(1), FXOGS_OFFHOOK,
E_HTSP_CONNECT] fxogs_proc_voice
*Mar 1 04:33:12.478: [1/1:1(1), FXOGS_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 04:33:12.514: [1/1:1(1), FXOGS_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH]
*Mar 1 04:33:12.526: [1/1:1(1), FXOGS_OFFHOOK,
E_HTSP_VOICE_CUT_THROUGH]


!--- Call connects and is answered.
!--- No signaling is reported (no answer supervision for ground-start).
!--- Call disconnected from VoIP leg below.

vdtl-2600-6d#htsp_release_req: cause 16, no_onhook 0
*Mar 1 04:33:22.590: [1/1:1(1), FXOGS_OFFHOOK,
E_HTSP_RELEASE_REQ] fxogs_offhook_release
*Mar 1 04:33:22.590: htsp_timer_stop
*Mar 1 04:33:22.590: htsp_timer_stop2 [Foreign Exchange Office 1/1:1(1)]
set signal state = 0x4
*Mar 1 04:33:22.590: htsp_timer - 2000 msec
*Mar 1 04:33:22.778: htsp_dsp_message: SEND/RESP_SIG_STATUS:
state=0xC timestamp=53840 systime=1640278
*Mar 1 04:33:22.778: [1/1:1(1), FXOGS_WAIT_ONHOOK,
E_DSP_SIG_1100] fxogs_waitonhook_onhook
*Mar 1 04:33:22.778: htsp_timer_stop
*Mar 1 04:33:22.778: htsp_timer - 2000 msec
*Mar 1 04:33:22.782: vnm_dsprm_close_cleanup
*Mar 1 04:33:24.778: [1/1:1(1), FXOGS_GUARD_OUT, E_HTSP_EVENT_TIMER]

相关的思科支持社区讨论

思科支持社区是您提问、解答问题、分享建议以及与工作伙伴协作的论坛。


相关信息


Document ID: 24642