无线/移动 : "无线, LAN (WLAN)"

在MS-DOS平台装载Aironet驱动程序

2015 年 8 月 28 日 - 机器翻译
其他版本: PDFpdf | 英语 (2015 年 4 月 22 日) | 反馈


目录


简介

本文解释如何安装在Microsoft DOS (MS-DOS)的Cisco Aironet驱动程序-基于笔记本电脑。

先决条件

要求

Cisco 建议您了解以下主题:

  • 无线局域网(WLAN)技术和期限

  • 个人计算机硬件主题

  • MS-DOS配置命令

使用的组件

本文档中的信息基于以下软件和硬件版本:

  • Aironet PCM 3xx或LMC 3xx客户端适配器

  • MS-DOS 6.22

  • DOS版本6.22的Aironet驱动程序

规则

有关文档规则的详细信息,请参阅 Cisco 技术提示规则

安装Aironet的DOS驱动

完成这些步骤为了安装DOS驱动:

  1. 这样创建config.sys文件

    DEVICE=A:\DOS\HIMEM.SYS
    DEVICE=A:\DOS\EMM386.EXE X=D000-DFFF FRAME=NONE
    DEVICEHIGH=A:\IBMDSS14.SYS
    DEVICEHIGH=A:\IBMDOSCS.SYS
    DEVICEHIGH=A:\DICRMU01.SYS /MA-D000-D7FF /SH=1 /IX=5,10,11,15
    DEVICE=A:\NET\IFSHLP.SYS
    DEVICE=A:\DOS\RAMDRIVE.SYS 2048 /e
    DEVICE=A:\DOS\ANSI.SYS
    DOS=HIGH,UMB
    FILES=40
    BUFFERS=30
    LASTDRIVE=Z
    SHELL=COMMAND.COM /e:512 /p

    IBMDSS14.SYS、IBMDOSCS.SYS和DICRMU01.SYS文件是PCMCIA卡,并且示例的插槽服务模拟IBM笔记本电脑。从笔记本电脑制造商的替代适当的文件如适当。

  2. 定制包括的cscpkt.ini文件对各自的需要:

    [CSCPKT]
            ;Initialization file for Infrastructure operating mode
    
            ; NOTE: The following are some keyword parameters that may
            ;be modified.  Any commented or omitted keyword parameter
            ;assumes the factory default.  For most situations the
            ;factory defaults will be appropriate.  In situations where
            ;the factory default needs to be modified, uncomment or add the
            ;keyword parameter line and set the appropriate keyword value.
    
            SSID="network_ssid"     ;Must match Access Point setting
            ;FragThreshold=2312     ;Packet size to start fragmenting
            ;RTSThreshold=2312      ;Packet size to start sending RTS/CTS
            ;DataRate1=0x02         ;(1)   Mbps supported data bit rate
            ;DataRate2=0x04         ;(2)   Mbps supported data bit rate
            ;DataRate3=0x0B         ;(5.5) Mbps supported data bit rate
            ;DataRate4=0x16         ;(11)  Mbps supported data bit rate
            ;RefreshInterval=10000  ;Inactivity time to check association
            ;PowerSaveMode="CAM"    ;Constant Awake Mode
            ;MaxPowerSave="OFF"     ;Maximum power save mode
            NodeName="CiscoPC"      ;Descriptive station name
            AuthType="WEPOPEN"      ;WEP with open authentication
    
            ;The adapter needs 32 16-bit I/O ports, and 1 non-sharable IRQ.
            ;The following lines should be uncommented and the appropriate
            ;values set in the following scenarios:
            ; 1) PCMCIA mode: Override the I/O port base and/or IRQ
            ;                 assigned by PCMCIA card services.
            ; 2) PCMCIA mode: PCMCIA card services is not being used.
            ; 3) ISA mode: Override the I/O port base and/or IRQ assigned
            ;              by Plug and Play.
            ; 4) ISA mode: Non-Plug and Play operation.
            
            ;PortBase=0x140
            ;IRQ=5
    
            ;If the PCMCIA interface is being used without PCMCIA card services,
            ;uncomment the following lines and set the appropriate values.
    
            Memory=0xD000
            Socket=0
    
            ;If the PCMCIA interface is not being used, set the appropriate
            ;value of "ISA" or "PCI".
    
            BusType="PCMCIA"
  3. 启动计算机装载上述config.sys文件

  4. 发出以下命令:

    a:>wepdos -365 -tx1 12345678901234567890123456
    
    setting key 1 to 12345678901234567890123456
    setting transmit key index to 1
  5. 发出以下命令:

    a:>cscpkt 0x65
    
    Cisco Wireless Packet Driver , version 2.04
    (c) Copyright 2000 Cisco System , Inc.
    All rights Reserved
    Card recognized as a radio in socket 00
    Driver Resources --> IO ports 0400-043F IRQ :03
    350 series Firmware 4.25.30
    Mac Address 00:09:7c:31:87:32
    

相关的思科支持社区讨论

思科支持社区是您提问、解答问题、分享建议以及与工作伙伴协作的论坛。


相关信息


Document ID: 25106