广域网 : T1/E1 & T3/E3

数据呼叫 E1 R2 信令的配置与故障排除

2016 年 10 月 24 日 - 机器翻译
其他版本: PDFpdf | 英语 (2015 年 8 月 22 日) | 反馈


目录


简介

本文为数据呼叫提供配置示例和故障排除技术发信号的E1 R2的。

先决条件

要求

在尝试此配置前,推荐您读E1 R2信令理论文档。关于发信号为语音应用的E1 R2的信息,参考本文E1 R2信令配置和故障排除

使用的组件

此配置使用下面软件和硬件版本开发并且被测试。此配置表示在Cisco 3640路由器和Cisco AS5300访问服务器之间的一个背对背实验室设置。

  • AS5300模拟客户端和运行Cisco IOSï ¿  ½软件版本12.2(3)。

  • 3640作为服务器和运行Cisco IOS软件版本12.1(10)。

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始(默认)配置。如果您使用的是真实网络,请确保您已经了解所有命令的潜在影响。

规则

有关文档规则的详细信息,请参阅 Cisco 技术提示规则

背景信息

E1 R2发信号允许Cisco通用接入服务器谈到也使用E1 R2发信号的中心局中继线。R2信令是对信道化E1网络是普通的国际信令标准。没有R2信令的标准。ITU-T Q.400-Q.490建议定义了R2,但是一定数量的国家(地区)用完全不同的方式实现R2。

Cisco系统通过支持R2信令的许多本地化的实施在其Cisco IOS软件方面针对此挑战。R2自定义本地化意味着R2信令为各种各样的国家(地区)和地理区域支持。思科在新的国家(地区)连续支持发信号变形的E1 R2。

注意: 仅ISDN调制解调器信道集中(MICA)和NextPort数字调制解调器模块支持R2功能。R2支持为Microcom调制解调器或非调制解调器应用程序没有提供。

配置

本部分提供有关如何配置本文档所述功能的信息。此配置为以下方案是有效:

  • 在E1 R2的Modem dialin连接

  • E1 R2背对背连接

  • Cisco路由器之间的E1 R2连接

注意: E1控制器的配置是相同的为数据或语音呼叫。唯一的差异是:

  • 对于数据呼叫您需要配置调制解调器接受呼叫。

  • 对于语音呼叫您需要配置语音端口接受呼叫。

注意: 要查找本文档所用命令的其他信息,请使用命令查找工具仅限注册用户)。

网络图

本文档使用下图所示的网络设置。

/image/gif/paws/23424/r2-back-back.gif

配置

配置数据呼叫的E1 R2包括两个一般步骤:

  • 配置 E1 R2

  • 配置调制解调器和相关问题

E1 R2配置根据从Telco得到的信息。参考本文E1 R2信令配置和故障排除关于E1 R2特定配置的更多信息。

调制解调器配置类似于那为所有接入服务器与,例如, PRI线路。

莫妮卡(AS5300)
Monica#show running-config 

controller E1 1

!--- E1 R2 configuration

 framing NO-CRC4
 clock source line secondary 1
 ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled
 cas-custom 1
  country easteurope use-defaults
interface Async60

!--- Interface configuration for outgoing call

 no ip address
 encapsulation ppp
 dialer in-band
 dialer rotary-group 3
 async mode dedicated
 ppp authentication chap
line 60

!--- Line configuration for outgoing call

 modem InOut
 modem dialout controller e1 1 

!--- Specify that e1 1 is used for outgoing call

 transport input all
 autoselect during-login
 autoselect ppp
安格拉(3640)
angela#show running-config 
interface Ethernet0/0
 ip address 10.200.20.2 255.255.255.0
controller E1 2/0

!--- E1 R2 configuration

 framing NO-CRC4
 ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled
 cas-custom 1
  country easteurope use-defaults
interface Group-Async1
 ip unnumbered Ethernet0/0
 encapsulation ppp
 async mode interactive
 peer default ip address pool DIAL_POOL
 ppp authentication chap
 group-range 97 114
!
ip local pool DIAL_POOL 105.41.30.101 105.41.30.132
line 97 114

!--- Line configuration for incoming calls

 modem InOut
 autocommand ppp
 transport input all
 autoselect during-login
 autoselect ppp

验证

当前没有可用于此配置的验证过程。

故障排除

本部分提供的信息可用于对配置进行故障排除。

关于故障排除E1 R2失败的更多信息,参考E1 R2信令配置和故障排除

故障排除命令

命令输出解释程序工具仅限注册用户)支持某些 show 命令,使用此工具可以查看对 show 命令输出的分析。

注意: 在发出 debug 命令之前,请参阅有关 Debug 命令的重要信息

  • show controllers e1 -显示是特定对控制器硬件的控制器状态。关于详细信息,参考了解show controllers e1命令

  • 如果所有硬件被认可, show diag -在Cisco3600,显示路由器的硬件信息,验证。

  • debug modem csm -调试(CSM)用于的呼叫交换模块连接在调制解调器的呼叫。

  • debug cas - CAS信令位状态的提供实时跟踪。

  • debug modem -显示在接入服务器的调制解调器线路活动。

  • show modem version -显示关于调制解调器固件、控制器和DSP编码的版本信息。

angela#show modem version
Slot 3:MICA-6DM Firmware, Source - flashow :/mica-modem-pw.2.7.3.0.bin
CP ver 2730 - 5/23/2001, CheckSum BCCEB316.
SP ver 2730 - 5/23/2001.
MICA 0: HW Version 2.1, Serial Number 21094004.
   
angela#show diag
Slot 2:
CE1 (Balanced) Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision A0
Serial number 11359839 Part number 800-01234-04
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 2A 01 01 00 AD 56 5F 50 04 D2 04 00 00 00 00
0x30: 50 00 00 00 98 11 24 00 FF FF FF FF FF FF FF FF

angela#show controllers e1 2/0
E1 2/0 is up.
Applique type is Channelized E1 - balanced
Far End Block Errors Detected
No alarms detected.
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (34 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
Secs
Robbed bit signals state:
timeslots rxA rxB rxC rxD txA txB txC txD
  1        1   0   0   1   1   0   0   1
  2        1   0   0   1   1   0   0   1
  3        1   0   0   1   1   0   0   1
  4        1   0   0   1   1   0   0   1
  5        1   0   0   1   1   0   0   1
  6        1   0   0   1   1   0   0   1
  7        1   0   0   1   1   0   0   1
  8        1   0   0   1   1   0   0   1
  9        1   0   0   1   1   0   0   1
  10       1   0   0   1   1   0   0   1
  11       1   0   0   1   1   0   0   1
  12       1   0   0   1   1   0   0   1
  13       1   0   0   1   1   0   0   1
  14       1   0   0   1   1   0   0   1
  15       1   0   0   1   1   0   0   1
  17       1   0   0   1   1   0   0   1
  18       1   0   0   1   1   0   0   1
  19       1   0   0   1   1   0   0   1
  20       1   0   0   1   1   0   0   1
  21       1   0   0   1   1   0   0   1
  22       1   0   0   1   1   0   0   1
  23       1   0   0   1   1   0   0   1
  24       1   0   0   1   1   0   0   1
  25       1   0   0   1   1   0   0   1
  26       1   0   0   1   1   0   0   1
  27       1   0   0   1   1   0   0   1
  28       1   0   0   1   1   0   0   1
  29       1   0   0   1   1   0   0   1
  30       1   0   0   1   1   0   0   1
  31       1   0   0   1   1   0   0   1

客户端拨号在服务器的调试的789个必要的解释。

monica#2.2.2.1 2060
Trying 2.2.2.1, 2060 ... Open
at
OK
atdt789

要改善请了解此debug输出,参考E1 R2信令理论文档。

angela#show debug
General OS:
   Modem control/process activation debugging is on

CAS:
   Channel Associated Signaling debugging is on
CSM Modem Management:
   Modem Management Call Switching Module debugging is on

angela#
Oct 29 15:59:46.591: Modem 255/255 CSM: received EVENT_CALL_DIAL_IN with call_id 0006
Oct 29 15:59:46.591: src 2/0/25 dest 255/0/255 cause 768
Oct 29 15:59:46.591: CSM: Next free modem = 3/6; statbits = 80010020
Oct 29 15:59:46.591: Modem 3/6 CSM: modem is allocated, modems free=17
Oct 29 15:59:46.591: Modem 3/6 CSM: (CSM_PROC_IDLE)<--DSX0_CALL
Oct 29 15:59:46.595: Modem 3/6 Mica: configured for Answer mode, 
 with Lower R2 signaling, 0x0 tone detection.
Oct 29 15:59:46.707: Modem 3/6 CSM: received EVENT_START_RX_TONE with call_id 0006
Oct 29 15:59:46.707: src 2/0/25 dest 3/0/6 cause 0
Oct 29 15:59:46.707: Modem 3/6 CSM:(CSM_PROC_IC_CAS_CHANNEL_LOCKED)<--DSX0_START_RX_TONE 
Oct 29 15:59:46.707: Modem 3/6 CSM:(CSM_PROC_IC_CAS_CHANNEL_LOCKED)<--CSM_EVENT_MODEM_SETUP
Oct 29 15:59:46.711: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE: R2_IN_IDLE R2 Got Event R2_START
Oct 29 15:59:46.715: Modem 3/6 Mica: in modem state CALL_SETUP
Oct 29 15:59:46.883: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_COLLECTED

!--- We can see number 7
   
Oct 29 15:59:46.887: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE:R2_IN_COLLECT_DNIS R2 Got Event 7
Oct 29 15:59:46.887: Modem 3/6 Mica: dialing number '1'

!--- MICA sends 1 (which means send next digit)

Oct 29 15:59:46.887: Modem 3/6 Mica: Detected dial digit '7'
Oct 29 15:59:46.959: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED
Oct 29 15:59:47.011: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_COLLECTED
Oct 29 15:59:47.011: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF
Oct 29 15:59:47.011: Modem 3/6 Mica: dialing number '#'
Oct 29 15:59:47.011: Modem 3/6 Mica: Detected dial digit '#'
Oct 29 15:59:47.099: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED
Oct 29 15:59:47.163: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_COLLECTED

!--- We can see number 8

Oct 29 15:59:47.163: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE: R2_IN_COLLECT_DNIS R2 Got Event 8
Oct 29 15:59:47.163: Modem 3/6 Mica: dialing number '1'

!--- MICA sends 1 (which means send next digit)

Oct 29 15:59:47.163: Modem 3/6 Mica: Detected dial digit '8'
Oct 29 15:59:47.235: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED
Oct 29 15:59:47.299: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_COLLECTED
Oct 29 15:59:47.299: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF
Oct 29 15:59:47.299: Modem 3/6 Mica: dialing number '#'
Oct 29 15:59:47.299: Modem 3/6 Mica: Detected dial digit '#'
Oct 29 15:59:47.375: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED
Oct 29 15:59:47.427: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_COLLECTED
Oct 29 15:59:47.427: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE:R2_IN_COLLECT_DNIS R2 Got Event 9
Oct 29 15:59:47.427: Modem 3/6 Mica: dialing number '1'

!--- MICA sends 1 (which means send next digit)

Oct 29 15:59:47.427: Modem 3/6 Mica: Detected dial digit '9'
Oct 29 15:59:47.499: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED
Oct 29 15:59:47.551: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_COLLECTED
Oct 29 15:59:47.551: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF
Oct 29 15:59:47.551: Modem 3/6 Mica: dialing number '#'
Oct 29 15:59:47.551: Modem 3/6 Mica: Detected dial digit '#'
Oct 29 15:59:47.639: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED

!--- NORMAL TIMEOUT--> 3 seconds

Oct 29 16:00:02.426: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_TIMER

!--- MICA sends 3 (which means ADDRESS COMPLETE)

Oct 29 16:00:02.426: Modem 3/6 Mica: dialing number '3#'
Oct 29 16:00:02.654: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED
Oct 29 16:00:02.678: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_COLLECTED

!--- We can see number 1 after we send 3

Oct 29 16:00:02.678: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE:R2_IN_CATEGORY R2 Got Event 1
Oct 29 16:00:02.682: r2_comp_category:R2_ALERTING

!--- MICA sends 3 (which means ADDRESS COMPLETE)

Oct 29 16:00:02.682: Modem 3/6 Mica: dialing number '6'
Oct 29 16:00:02.682: Modem 3/6 Mica: Detected dial digit '1'
Oct 29 16:00:02.834: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_COLLECTED
Oct 29 16:00:02.834: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE: R2_IN_COMPLETE R2 Got Event R2_TONE_OFF
Oct 29 16:00:02.834: Modem 3/6 CSM: Pending digit generation for #
Oct 29 16:00:02.834: Modem 3/6 Mica: Detected dial digit '#'
Oct 29 16:00:02.854: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED
Oct 29 16:00:02.854: Modem 3/6 Mica: dialing number '#'
Oct 29 16:00:02.854: Modem 3/6 CSM: Generate 1 pending digit(s) #
Oct 29 16:00:02.918: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--MODEM_DIGITS_GENERATED
Oct 29 16:00:03.834: R2 Incoming Modem(3/6): DSX (E1 2/0:25): 
STATE:R2_IN_WAIT_GUARD R2 Got Event R2_TONE_TIMER
Oct 29 16:00:03.834: R2_IN_IDLE:2 r2_in_connect called
Oct 29 16:00:03.834: Modem 3/6 CSM:(CSM_PROC_IC_CAS_COLLECT_DIGITS)<--ADDR_INFO_COLLECTED
Oct 29 16:00:03.842: Modem 3/6 CSM: received EVENT_CHANNEL_CONNECTED with call_id 0006
Oct 29 16:00:03.842: src 2/0/25 dest 3/0/6 cause 0
Oct 29 16:00:03.842: Modem 3/6 CSM:(CSM_PROC_IC_CAS_ANSWER_CALL)<--DSX0_CONNECTED
Oct 29 16:00:04.926: Modem 3/6 Mica: in modem state CONNECT
Oct 29 16:00:12.290: Modem 3/6 Mica: in modem state LINK
Oct 29 16:00:21.278: Modem 3/6 Mica: in modem state TRAINUP
Oct 29 16:00:23.002: Modem 3/6 Mica: in modem state EC_NEGOTIATING
Oct 29 16:00:23.170: Modem 3/6 CSM:(CSM_PROC_CAS_WAIT_FOR_CARRIER)<--MODEM_CONNECTED
Oct 29 16:00:23.170: Modem 3/6 Mica: in modem state STEADY
Oct 29 16:00:23.194: Modem 3/6 Mica: CONNECT at 33600/33600 (Tx/Rx), V34+, LAPM, V42bis
Oct 29 16:00:23.446: TTY103: DSR came up
Oct 29 16:00:23.446: tty103: Modem: IDLE->(unknown)
Oct 29 16:00:23.446: TTY103: Autoselect started
Oct 29 16:00:23.446: TTY103: create timer type 0, 120 seconds
---------
monica#show debug
General OS:
   Modem control/process activation debugging is on
CAS:
   Channel Associated Signaling debugging is on
Modem Management:
   Modem Management Call Switching Module debugging is on

monica#
Oct 29 15:59:46.540: Mica Modem(1/59): Rcvd Dial String(T789)
Oct 29 15:59:46.540: Mica Modem(1/59): Dropped character T
Oct 29 15:59:46.540: Mica Modem(1/59): Dial String to be processed (789)
Oct 29 15:59:46.540: Mica Modem(1/59): End of Dial String
Oct 29 15:59:46.540: CSM_PROC_IDLE: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 59
Oct 29 15:59:46.540: csm_get_signaling_channel csm_call_info->bchan_num 0xFFFFFFFF
Oct 29 15:59:46.540: csm_get_signaling_channel dchan_index=24952,next_index=0,
dchan_info=0x62269D0C
Oct 29 15:59:46.540: csm_get_signaling_channel csm_call_info->bchan_num 0xFFFFFFFF
Oct 29 15:59:46.540: csm_get_signaling_channel dchan_index=0,next_index=1,
dchan_info=0x61D37574
Oct 29 15:59:46.540: CSM_RX_CAS_EVENT_FROM_NEAT:(8007): 
EVENT_CHANNEL_LOCK at slot 1 port 59 on ctrlr 1 chan 25
Oct 29 15:59:46.544: CSM_PROC_OC4_DIALING: 
CSM_EVENT_DSX0_BCHAN_ASSIGNED at slot 1, port 59
Oct 29 15:59:46.544: csm_connect_pri_vdev: 
TS allocated at bp_stream 1, bp_Ch 9, vdev_common 0x61B7BBAC 1/59
Oct 29 15:59:46.544: Mica Modem(1/59): Configure(0x1 = 0x1)
Oct 29 15:59:46.544: Mica Modem(1/59): Configure(0x23 = 0x4)
Oct 29 15:59:46.544: Mica Modem(1/59): Call Setup
Oct 29 15:59:46.544: from Trunk(0): (1/25): Tx SEIZURE (ABCD=0001)
Oct 29 15:59:46.616: Mica Modem(1/59): State Transition to Call Setup
Oct 29 15:59:46.712: from Trunk(0): (1/25): Rx SEIZURE_ACK (ABCD=1101)
Oct 29 15:59:46.752: CSM_RX_CAS_EVENT_FROM_NEAT:(8007): 
EVENT_START_TX_TONE at slot 1 and port 59
Oct 29 15:59:46.752: CSM_PROC_OC4_DIALING: 
CSM_EVENT_DSX0_START_TX_TONE at slot 1, port 59
Oct 29 15:59:46.752: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_IDLE R2 Got Event R2_START
Oct 29 15:59:46.752: Mica Modem(1/59): Generate digits:called_party_num=# len=1
Oct 29 15:59:46.752: Mica Modem(1/59): Will Generate digits:called_party_num=7 len=1
Oct 29 15:59:46.824: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 15:59:46.824: Mica Modem(1/59): Generate digits
Oct 29 15:59:46.900: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 15:59:46.944: Mica Modem(1/59): Rcvd Digit detected(1)
Oct 29 15:59:46.944: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_A R2 Got Event 1
Oct 29 15:59:46.944: Mica Modem(1/59): Generate digits:called_party_num=# len=1
Oct 29 15:59:47.020: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 15:59:47.108: Mica Modem(1/59): Rcvd Digit detected(#)
Oct 29 15:59:47.108: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_A R2 Got Event R2_TONE_OFF
Oct 29 15:59:47.108: Mica Modem(1/59): Generate digits:called_party_num=8 len=1
Oct 29 15:59:47.184: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 15:59:47.228: Mica Modem(1/59): Rcvd Digit detected(1)
Oct 29 15:59:47.228: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_A R2 Got Event 1
Oct 29 15:59:47.228: Mica Modem(1/59): Generate digits:called_party_num=# len=1
Oct 29 15:59:47.304: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 15:59:47.380: Mica Modem(1/59): Rcvd Digit detected(#)
ct 29 15:59:47.380: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_A R2 Got Event R2_TONE_OFF
Oct 29 15:59:47.380: Mica Modem(1/59): Generate digits:called_party_num=9 len=1
Oct 29 15:59:47.440: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 15:59:47.484: Mica Modem(1/59): Rcvd Digit detected(1)
Oct 29 15:59:47.484: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_A R2 Got Event 1
Oct 29 15:59:47.484: Mica Modem(1/59): Generate digits:called_party_num=# len=1
Oct 29 15:59:47.560: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 15:59:47.636: Mica Modem(1/59): Rcvd Digit detected(#)
Oct 29 15:59:47.636: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_A R2 Got Event R2_TONE_OFF
Oct 29 16:00:02.521: Mica Modem(1/59): Rcvd Digit detected(3)
Oct 29 16:00:02.521: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_A R2 Got Event 3
Oct 29 16:00:02.521: Mica Modem(1/59): Generate digits:called_party_num=# len=1
Oct 29 16:00:02.593: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 16:00:02.641: Mica Modem(1/59): Rcvd Digit detected(#)
Oct 29 16:00:02.641: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_B R2 Got Event R2_TONE_OFF
Oct 29 16:00:02.641: Mica Modem(1/59): Generate digits:called_party_num=1 len=1
Oct 29 16:00:02.713: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 16:00:02.745: Mica Modem(1/59): Rcvd Digit detected(6)
Oct 29 16:00:02.745: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_PROCESS_B R2 Got Event 6
Oct 29 16:00:02.745: Mica Modem(1/59): Generate digits:called_party_num=# len=1
Oct 29 16:00:02.745: CSM_PROC_OC4_DIALING: 
CSM_EVENT_ADDR_INFO_COLLECTED at slot 1, port 59
Oct 29 16:00:02.821: Mica Modem(1/59): Rcvd Digits Generated
Oct 29 16:00:02.925: Mica Modem(1/59): Rcvd Digit detected(#)
Oct 29 16:00:02.925: R2 Outgoing Modem(1/59): DSX (E1 1:25): 
STATE: R2_OUT_IDLE R2 Got Event R2_TONE_OFF
Oct 29 16:00:03.845: from Trunk(0): (1/25): Rx ANSWERED (ABCD=0101)
Oct 29 16:00:03.885: CSM_RX_CAS_EVENT_FROM_NEAT:(8007): 
EVENT_CHANNEL_CONNECTED at slot 1 and port 59
Oct 29 16:00:03.885: CSM_PROC_OC5_WAIT_FOR_CARRIER: 
CSM_EVENT_DSX0_CONNECTED at slot 1, port 59
Oct 29 16:00:03.885: Mica Modem(1/59): Link Initiate
Oct 29 16:00:03.917: Mica Modem(1/59): State Transition to Connect
Oct 29 16:00:06.709: Mica Modem(1/59): State Transition to unknown
Oct 29 16:00:12.497: Mica Modem(1/59): State Transition to Link
Oct 29 16:00:15.197: Mica Modem(1/59): State Transition to unknown
Oct 29 16:00:17.241: Mica Modem(1/59): State Transition to unknown
Oct 29 16:00:21.385: Mica Modem(1/59): State Transition to Trainup
Oct 29 16:00:23.061: Mica Modem(1/59): State Transition to EC Negotiating
Oct 29 16:00:23.245: Mica Modem(1/59): State Transition to Steady State

相关信息


Document ID: 23424