长距离以太网 (LRE) 和数字用户线 (xDSL) : 非对称数字用户线 (ADSL)

在 Cisco 2600 上配置 PPPoE 客户端以连接到非 Cisco DSL CPE

2016 年 10 月 24 日 - 机器翻译
其他版本: PDFpdf | 英语 (2015 年 11 月 11 日) | 反馈


目录


简介

本文解释如何通过以太网接口支持思科IOSï ¿  ½路由器连接的一个以太网点对点协议(PPPoE)客户端到DSL调制解调器或另一个供应商的DSL客户端前置设备(CPE)。

ISP经常为他们的用户提供DSL调制解调器,这种调制解调器有一个以太网接口连接用户以太网段,另外还有一个接口提供DSL线路连接。在这种情况下,如果CPE为任何IP连通性或增强功能不是可配置在DSL, DSL调制解调器只作为网桥。这对一个PPPoE客户端PC只限制您的连接。增加Cisco IOS路由器连接对DSL调制解调器的以太网,您能运行在Cisco路由器的PPPoE客户端IOS功能。这能连接在以太网段的多台PC连接对Cisco IOS路由器。使用使用Cisco IOS路由器,您能提高您的DSL连接和所有IOS功能,例如安全、网络地址转换(NAT)和动态主机配置协议(DHCP)到内部主机。

PPPoE功能允许您在简单桥接以太网连接的客户端上启动PPP会话。会话运输在ATM链路通过压缩的以太网桥接帧。您能终止会话在本地交换运营商中心局或ISP入网点。

先决条件

要求

本文档没有任何特定的要求。

使用的组件

本文档中的信息基于以下软件和硬件版本:

  • Cisco 827-4V CPE IOS软件版本12.1(1)XB

  • 运行Cisco IOS软件版本12.2(2)T1镜像的Cisco 2611路由器

  • 运行Cisco IOS软件版本12.1(5)dc1镜像的Cisco 6400通用接入集中器(UAC)

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始(默认)配置。如果您使用的是真实网络,请确保您已经了解所有命令的潜在影响。

规则

有关文档规则的详细信息,请参阅 Cisco 技术提示规则

配置

在此部分,您提交与用于的信息为了配置在本文描述的功能。

注意: 要查找有关本文档中所使用的命令的详细信息,请使用命令查找工具仅限注册用户)。

网络图

本文档使用此图所示的网络设置。

/image/gif/paws/4105/2600pppoe_4105-a.gif

注意: 在本文中, PPPoE客户端连接从Cisco路由器首次。这是Cisco 2611路由器在此配置方面。Cisco 827路由器在图表中代表非Cisco的DSL CPE。

配置

本文档使用以下配置。

2611 路由器
! 
hostname pooh 
ip host rund 172.17.247.195 
! 
ip subnet-zero 
no ip domain-lookup 
! 
vpdn enable 
no vpdn logging 
! 
vpdn-group 1 
request-dialin 
protocol pppoe 
! 
! 
! 
! 
interface Ethernet0/0 
ip address 10.200.56.22 255.255.255.0 
ip nat inside 
no ip mroute-cache 
! 
! 
! 
! 
interface Ethernet0/1 
no ip address 
pppoe enable 
pppoe-client dial-pool-number 1 
! 
interface Dialer1 
ip address negotiated 
ip nat outside 
ip mtu 1492 
encapsulation ppp 
no ip mroute-cache 
dialer pool 1 
dialer-group 1 
ppp authentication pap 
ppp pap sent-username cisco password cisco1 
! 
ip classless 
no ip http server 
! 
dialer-list 1 protocol ip permit 
ip nat inside source list 1 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 dialer1 
access-list 1 permit 10.200.56.0 0.0.0.255 
! 
line con 0 
exec-timeout 0 0 
transport input none 
line vty 0 4 
login 
password ww 
! 
end

Cisco DSL 827路由器
Building configuration... 
Current configuration : 821 bytes 
! 
version 12.2 
no service pad 
service timestamps debug uptime 
service timestamps log uptime 
no service password-encryption 
! 
hostname Chansey 
! 
! 
ip subnet-zero 
no ip domain-lookup 
! 
! 
! 
interface Ethernet0 
 no ip address  
 bridge-group 1 
! 
interface ATM0 
 no ip address 
 no atm ilmi-keepalive 
 bundle-enable 
 bridge-group 1 
 dsl operating-mode auto 
! 
interface ATM0.1 point-to-point 
 pvc 53/53
!--- vpi/vci given by the ISP 
 ! 
! 
ip classless 
ip http server 
!  
bridge 1 protocol ieee 
! 
line con 0 
 exec-timeout 0 0 
 stopbits 1 
line vty 0 4 
 exec-timeout 0 0 
 password ww 
 login local 
! 
scheduler max-task-time 5000 
end

Cisco 6400路由器
Current configuration : 3231 bytes 
! 
version 12.1 
no service single-slot-reload-enable 
service timestamps debug uptime 
service timestamps log uptime 
no service password-encryption 
! 
hostname alyssa_nrp1 
! 
logging rate-limit console 10 except errors 
aaa new-model 
aaa authentication ppp default local 
enable password ww 
! 
username cisco password  cisco1 
redundancy 
main-cpu 
auto-sync standard 
no secondary console enable 
ip subnet-zero 
ip cef 
vpdn enable 
no vpdn logging 
! 
vpdn-group cisco 
accept-dialin 
protocol pppoe 
virtual-template 2 
! 
! 
! 
! 
! 
! 
! 
interface Loopback5 
ip address 212.93.195.100 255.255.255.0 
! 
! 
interface ATM0/0/0 
no ip address 
no ip mroute-cache 
load-interval 30 
atm pvc 16 0 16 ilmi 
no atm ilmi-keepalive 
pvc 10/100 
! 
hold-queue 1000 in 
! 
interface ATM0/0/0.60 multipoint 
pvc 6/60 
encapsulation aal5snap 
protocol pppoe 
! 
! 
interface Ethernet0/0/1 
no ip address 
! 
interface Ethernet0/0/0 
ip address 10.200.56.8 255.255.255.0 
! 
interface FastEthernet0/0/0 
no ip address 
full-duplex 
! 
! 
interface Virtual-Template2 
ip unnumbered Loopback5 
ip mtu 1492 
no ip route-cache cef 
peer default ip address pool nrp1 
ppp authentication pap 
! 
ip local pool nrp1 212.93.198.1 
ip classless 
! 
! 
line con 0 
exec-timeout 0 0 
password ww 
transport input none 
line aux 0 
line vty 0 4 
exec-timeout 0 0 
password ww 
! 
! 
end  

验证

本部分提供了可用于确认您的配置是否正常运行的信息。

命令输出解释程序工具仅限注册用户)支持某些 show 命令,使用此工具可以查看对 show 命令输出的分析。

  • show vpdn session全显示VPDN会话信息。此信息包括接口、通道、用户名、数据包、状态和窗口统计信息。

  • show interface ethernet 0/1 —显示关于以太网接口的信息在路由器。

  • show interfaces dialer 1 —显示关于拨号程序的信息在路由器。

  • show ip local pool nrp1 —显示关于ip local pool的信息。

  • show ip route —显示关于Ip route的信息在路由器。

这是在Cisco 2611的show vpdn session all命令输出。

pooh#show vpdn session all
%No active L2TP tunnels
%No active L2F tunnels
%No active PPTP tunnels
PPPoE Session Information Total tunnels 1 sessions 1
session id: 1

!--- Local MAC address.

local MAC address: 0030.9424.af21, 
remote MAC address: 0050.736f.4c37
virtual access interface: Vi1, outgoing interface: Et0/1
599 packets sent, 599 received
9202 bytes sent, 8154 received

!--- Verify that the outgoing interface for the PPPoE session 
!--- is Ethernet0/1 and the local MAC address that displays is the 
!--- MAC address of Ethernet0/1. The remote MAC address that displays 
!--- is the MAC address of the Aggregator device (6400).  
!--- You can see it on the 6400 as the local MAC address in the 
!--- show vpdn session on the 6400.

这是在Cisco 2611的show interface ethernet 0/1命令输出。

pooh#show interface ethernet 0/1
Ethernet0/1 is up, line protocol is up
Hardware is AmdP2, address is 0030.9424.af21 (bia 0030.9424.af21
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:40, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
739 packets input, 64127 bytes, 0 no buffer
Received 57 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
1153 packets output, 89766 bytes, 0 underruns(1/0/0)
0 output errors, 1 collisions, 1 interface resets
0 babbles, 0 late collision, 2 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out

这是在Cisco 2611的show interfaces dialer 1命令输出。

pooh#show interfaces dialer 1
Dialer1 is up, line protocol is up (spoofing)
Hardware is Unknown
Internet address is 212.93.198.1/32
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
DTR is pulsed for 1 seconds on reset
Interface is bound to Vi1
Last input never, output never, output hang never
Last clearing of "show interface" counters 01:38:43
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations  0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
403 packets input, 6082 bytes
403 packets output, 6978 bytes
Bound to:
Virtual-Access1 is up, line protocol is up
Hardware is Virtual Access interface
MTU 1500 bytes, BW 100000 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
Interface is bound to Di1 (Encapsulation PPP)
LCP Open
Listen: CDPCP
Open: IPCP
Last input 00:00:09, output never, output hang never
Last clearing of "show interface" counters 00:35:16
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
430 packets input, 6453 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
430 packets output, 7400 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions

这是在Cisco 6400的show vpdn session all命令输出。

alyssa_nrp1#show vpdn session  all
%No active L2TP tunnels
%No active L2F tunnels
%No active PPTP tunnels
PPPoE Session Information Total tunnels 1 sessions 1
session id: 1
local MAC address: 0050.736f.4c37, remote MAC address: 0030.9424.af21
virtual access interface: Vi3, outgoing interface: AT0/0/0, vc: 6/60
495 packets sent, 494 received
7369 bytes sent, 7346 received

这是在Cisco 6400的show ip local pool nrp1命令输出。

alyssa_nrp1#show ip local pool nrp1
Pool                     Begin           End             Free  In use
nrp1                    212.93.198.1    212.93.198.1       0       1
Available addresses:
None
Inuse addresses:
212.93.198.1       Vi3                         nrp1

这是在Cisco 6400的show ip route命令输出。

alyssa_nrp1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
212.93.198.0/32 is subnetted, 1 subnets
C       212.93.198.1 is directly connected, Virtual-Access3  

!--- You have to see the installed route for the remote PPPoE session.


C    212.93.195.0/24 is directly connected, Loopback5
10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
C       10.200.56.0/24 is directly connected, Ethernet0/0/0

故障排除

本部分提供的信息可用于对配置进行故障排除。

故障排除命令

命令输出解释程序工具仅限注册用户)支持某些 show 命令,使用此工具可以查看对 show 命令输出的分析。

注意: 在发出 debug 命令之前,请参阅有关 debug 命令的重要信息

  • show debugging —显示关于路由器的调试信息。

这是在Cisco 2611的show debugging命令输出。

pooh#show debugging
PPP:
PPP protocol negotiation debugging is on
VPN:
PPPoE protocol events debugging is on
PPPoE control packets debugging is on
01:54:21:  Sending PADI: Interface = Ethernet0/1
01:54:21: pppoe_send_padi:
FF FF FF FF FF FF 00 30 94 24 AF 21 88 63 11 09
00 00 00 0C 01 01 00 00 01 03 00 04 82 2E 39 F0
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...
01:54:21: PPPoE 0: I PADO L:0030.9424.af21 R:0050.736f.4c37 Et0/1
00 30 94 24 AF 21 00 50 73 6F 4C 37 88 63 11 07
00 00 00 2F 01 01 00 00 01 03 00 04 82 2E 39 F0
01 02 00 0B 61 6C 79 73 73 61 5F 6E 72 70 31 ...
01:54:23:  PPPOE: we've got our pado and the pado timer went off
01:54:23: OUT PADR from PPPoE tunnel
00 50 73 6F 4C 37 00 30 94 24 AF 21 88 63 11 19
00 00 00 2F 01 01 00 00 01 03 00 04 82 2E 39 F0
01 02 00 0B 61 6C 79 73 73 61 5F 6E 72 70 31 ...
01:54:23: PPPoE 1: I PADS L:0030.9424.af21 R:0050.736f.4c37 Et0/1
00 30 94 24 AF 21 00 50 73 6F 4C 37 88 63 11 65
00 01 00 2F 01 01 00 00 01 03 00 04 82 2E 39 F0
01 02 00 0B 61 6C 79 73 73 61 5F 6E 72 70 31 ...
01:54:23: IN PADS from PPPoE tunnel
01:54:23: Vi1 Debug: Condition 1, interface Di1 triggered, count 1
01:54:23: %DIALER-6-BIND: Interface Vi1 bound to profile Di1
01:54:23: PPPoE: Virtual Access interface obtained.
01:54:23: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
01:54:23: Vi1 PPP: Treating connection as a callout
01:54:23: Vi1 PPP: Phase is ESTABLISHING, Active Open [0 sess, 0 load]
01:54:23: Vi1 PPP: No remote authentication for call-out
01:54:23: Vi1 LCP: O CONFREQ [Closed] id 1 len 10
01:54:23: Vi1 LCP:    MagicNumber 0x30FCDE42 (0x050630FCDE42)
01:54:23: Vi1 LCP: I CONFACK [REQsent] id 1 len 10
01:54:23: Vi1 LCP:    MagicNumber 0x30FCDE42 (0x050630FCDE42)
01:54:25: Vi1 LCP: I CONFREQ [ACKrcvd] id 2 len 18
01:54:25: Vi1 LCP:    MRU 1492 (0x010405D4)
01:54:25: Vi1 LCP:    AuthProto PAP (0x0304C023)
01:54:25: Vi1 LCP:    MagicNumber 0x5C799D85 (0x05065C799D85)
01:54:25: Vi1 LCP: O CONFNAK [ACKrcvd] id 2 len 8
01:54:25: Vi1 LCP:    MRU 1500 (0x010405DC)
01:54:25: Vi1 LCP: TIMEout: State ACKrcvd
01:54:25: Vi1 LCP: O CONFREQ [ACKrcvd] id 2 len 10
01:54:25: Vi1 LCP:    MagicNumber 0x30FCDE42 (0x050630FCDE42)
01:54:25: Vi1 LCP: I CONFREQ [REQsent] id 3 len 18
01:54:25: Vi1 LCP:    MRU 1500 (0x010405DC)
01:54:25: Vi1 LCP:    AuthProto PAP (0x0304C023)
01:54:25: Vi1 LCP:    MagicNumber 0x5C799D85 (0x05065C799D85)
01:54:25: Vi1 LCP: O CONFACK [REQsent] id 3 len 18
01:54:25: Vi1 LCP:    MRU 1500 (0x010405DC)
01:54:25: Vi1 LCP:    AuthProto PAP (0x0304C023)
01:54:25: Vi1 LCP:    MagicNumber 0x5C799D85 (0x05065C799D85)
01:54:25: Vi1 LCP: I CONFACK [ACKsent] id 2 len 10
01:54:25: Vi1 LCP:    MagicNumber 0x30FCDE42 (0x050630FCDE42)
01:54:25: Vi1 LCP: State is Open
01:54:25: Vi1 PPP: Phase is AUTHENTICATING, by the peer [0 sess, 0 load]
01:54:25: Vi1 PAP: O AUTH-REQ id 4 len 18 from "cisco"
01:54:25: Vi1 PAP: I AUTH-ACK id 4 len 5
01:54:25: Vi1 PPP: Phase is UP [0 sess, 0 load]
01:54:25: Vi1 IPCP: O CONFREQ [Closed] id 1 len 10
01:54:25: Vi1 IPCP:    Address 0.0.0.0 (0x030600000000)
01:54:25: Vi1 CDPCP: O CONFREQ [Closed] id 1 len 4
01:54:25: Vi1 IPCP: I CONFREQ [REQsent] id 1 len 10
01:54:25: Vi1 IPCP:    Address 212.93.195.100 (0x0306D45DC364)
01:54:25: Vi1 IPCP: O CONFACK [REQsent] id 1 len 10
01:54:25: Vi1 IPCP:    Address 212.93.195.100 (0x0306D45DC364)
01:54:25: Vi1 IPCP: I CONFNAK [ACKsent] id 1 len 10
01:54:25: Vi1 IPCP:    Address 212.93.198.1 (0x0306D45DC601)
01:54:25: Vi1 IPCP: O CONFREQ [ACKsent] id 2 len 10
01:54:25: Vi1 IPCP:    Address 212.93.198.1 (0x0306D45DC601)
01:54:25: Vi1 LCP: I PROTREJ [Open] id 4 len 10 protocol CDPCP
(0x820701010004)
01:54:25: Vi1 CDPCP: State is Closed
01:54:25: Vi1 IPCP: I CONFACK [ACKsent] id 2 len 10
01:54:25: Vi1 IPCP:    Address 212.93.198.1 (0x0306D45DC601)
01:54:25: Vi1 IPCP: State is Open
01:54:25: Di1 IPCP: Install negotiated IP interface address 212.93.198.1
01:54:25: Di1 IPCP: Install route to 212.93.195.100
01:54:26: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1,
changed state to up

这是在Cisco 6400的show debugging命令输出。

*Aug 16 15:58:51.346: PPPoE: IN PADI discovery packet 
*Aug 16 15:58:51.346:   PPPoE: LMAC:ffff.ffff.ffff RMAC:0030.9424.af21 6/60 
AT0/0/0.60 
FF FF FF FF FF FF 00 30 94 24 AF 21 88 63 11 09 
00 00 00 0C 01 01 00 00 01 03 00 04 82 2E 39 F0 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ... 
*Aug 16 15:58:51.346: PPPoE: PADO OUT from PPPoE tunnel 
*Aug 16 15:58:51.346:   PPPoE: LMAC:0050.736f.4c37 RMAC:0030.9424.af21 6/60 
AT0/0/0.60 
00 05 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30 
94 24 AF 21 00 50 73 6F 4C 37 88 63 11 07 00 00 
00 2F 01 01 00 00 01 03 00 04 82 2E 39 F0 01 ... 
*Aug 16 15:58:53.390: PPPoE: IN PADR discovery packet 
*Aug 16 15:58:53.390:   PPPoE: LMAC:0050.736f.4c37 RMAC:0030.9424.af21 6/60 
AT0/0/0.60 
00 50 73 6F 4C 37 00 30 94 24 AF 21 88 63 11 19 
00 00 00 2F 01 01 00 00 01 03 00 04 82 2E 39 F0 
01 02 00 0B 61 6C 79 73 73 61 5F 6E 72 70 31 ... 
*Aug 16 15:58:53.394: Vi3 PPP: Phase is DOWN, Setup [0 sess, 0 load] 
*Aug 16 15:58:53.418: PPPoE: Create session: 1 
*Aug 16 15:58:53.418: PPPoE:  1: Created 
*Aug 16 15:58:53.418:   PPPoE: LMAC:0050.736f.4c37 RMAC:0030.9424.af21 6/60 
AT0/0/0.60 
*Aug 16 15:58:53.418: PPPoE: PADS OUT from PPPoE tunnel 
*Aug 16 15:58:53.418:   PPPoE: LMAC:0050.736f.4c37 RMAC:0030.9424.af21 6/60 
AT0/0/0.60 
00 05 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30 
94 24 AF 21 00 50 73 6F 4C 37 88 63 11 65 00 01 
00 2F 01 01 00 00 01 03 00 04 82 2E 39 F0 01 ... 
2d08h: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state to up 
*Aug 16 15:58:53.426: Vi3 PPP: Treating connection as a dedicated line 
*Aug 16 15:58:53.426: Vi3 PPP: Phase is ESTABLISHING, Active Open [0 sess, 
0 load] 
*Aug 16 15:58:53.426: Vi3 LCP: O CONFREQ [Closed] id 1 len 18 
*Aug 16 15:58:53.426: Vi3 LCP:    MRU 1492 (0x010405D4) 
*Aug 16 15:58:53.426: Vi3 LCP:    AuthProto PAP (0x0304C023) 
*Aug 16 15:58:53.426: Vi3 LCP:    MagicNumber 0x5C7E3144 (0x05065C7E3144) 
*Aug 16 15:58:53.466: Vi3 LCP: I CONFREQ [REQsent] id 1 len 10 
*Aug 16 15:58:53.466: Vi3 LCP:    MagicNumber 0x31017223 (0x050631017223) 
*Aug 16 15:58:53.466: Vi3 LCP: O CONFACK [REQsent] id 1 len 10 
*Aug 16 15:58:53.466: Vi3 LCP:    MagicNumber 0x31017223 (0x050631017223) 
*Aug 16 15:58:53.470: Vi3 LCP: I CONFNAK [ACKsent] id 1 len 8 
*Aug 16 15:58:53.470: Vi3 LCP:    MRU 1500 (0x010405DC) 
*Aug 16 15:58:53.470: Vi3 LCP: O CONFREQ [ACKsent] id 2 len 18 
*Aug 16 15:58:53.470: Vi3 LCP:    MRU 1500 (0x010405DC) 
*Aug 16 15:58:53.470: Vi3 LCP:    AuthProto PAP (0x0304C023) 
*Aug 16 15:58:53.470: Vi3 LCP:    MagicNumber 0x5C7E3144 (0x05065C7E3144) 
*Aug 16 15:58:53.510: Vi3 LCP: I CONFACK [ACKsent] id 2 len 18 
*Aug 16 15:58:53.510: Vi3 LCP:    MRU 1500 (0x010405DC) 
*Aug 16 15:58:53.510: Vi3 LCP:    AuthProto PAP (0x0304C023) 
*Aug 16 15:58:53.510: Vi3 LCP:    MagicNumber 0x5C7E3144 (0x05065C7E3144) 
*Aug 16 15:58:53.510: Vi3 LCP: State is Open 
*Aug 16 15:58:53.510: Vi3 PPP: Phase is AUTHENTICATING, by this end [0 
sess, 0 load] 
*Aug 16 15:58:53.514: Vi3 PAP: I AUTH-REQ id 5 len 18 from "cisco" 
*Aug 16 15:58:53.514: Vi3 PPP: Phase is FORWARDING [0 sess, 0 load] 
*Aug 16 15:58:53.514: Vi3 PPP: Phase is AUTHENTICATING [0 sess, 0 load] 
*Aug 16 15:58:53.514: Vi3 PAP: Authenticating peer cisco 
*Aug 16 15:58:53.514: Vi3 PAP: O AUTH-ACK id 5 len 5 
*Aug 16 15:58:53.514: Vi3 PPP: Phase is UP [0 sess, 0 load] 
*Aug 16 15:58:53.514: Vi3 IPCP: O CONFREQ [Closed] id 1 len 10 
*Aug 16 15:58:53.514: Vi3 IPCP:    Address 212.93.195.100 (0x0306D45DC364) 
*Aug 16 15:58:53.574: Vi3 IPCP: I CONFREQ [REQsent] id 1 len 10 
*Aug 16 15:58:53.574: Vi3 IPCP:    Address 0.0.0.0 (0x030600000000) 
*Aug 16 15:58:53.574: Vi3 IPCP: Pool returned 212.93.198.1 
*Aug 16 15:58:53.574: Vi3 IPCP: O CONFNAK [REQsent] id 1 len 10 
*Aug 16 15:58:53.574: Vi3 IPCP:    Address 212.93.198.1 (0x0306D45DC601) 
*Aug 16 15:58:53.574: Vi3 CDPCP: I CONFREQ [Not negotiated] id 1 len 4 
*Aug 16 15:58:53.574: Vi3 LCP: O PROTREJ [Open] id 3 len 10 protocol CDPCP 
(0x820701010004) 
*Aug 16 15:58:53.574: Vi3 IPCP: I CONFACK [REQsent] id 1 len 10 
*Aug 16 15:58:53.574: Vi3 IPCP:    Address 212.93.195.100 (0x0306D45DC364) 
*Aug 16 15:58:53.618: Vi3 IPCP: I CONFREQ [ACKrcvd] id 2 len 10 
*Aug 16 15:58:53.618: Vi3 IPCP:    Address 212.93.198.1 (0x0306D45DC601) 
*Aug 16 15:58:53.618: Vi3 IPCP: O CONFACK [ACKrcvd] id 2 len 10 
*Aug 16 15:58:53.618: Vi3 IPCP:    Address 212.93.198.1 (0x0306D45DC601) 
*Aug 16 15:58:53.618: Vi3 IPCP: State is Open 
*Aug 16 15:58:53.622: Vi3 IPCP: Install route to 212.93.198.1 
2d08h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access3, 
changed state to up 

相关信息


Document ID: 4105