IP : 串行隧道 (STUN)

在帧中继上配置带有本地确认的 BSTUN 点对点连接

2015 年 8 月 28 日 - 机器翻译
其他版本: PDFpdf | 英语 (2015 年 4 月 22 日) | 反馈


目录


简介

Bisync Serial Tunnel (BSTUN)功能使得支持使用双同步数据链路协议的设备。此协议使得企业在支持他们的系统网络体系结构(SNA)和多协议数据流的同一个网络上传输Bisync数据流,减少对独立的双同步设备的需求。使用帧中继,您可以使用本地确认功能提供会话在BSTUN对等体的本地终接。

在本例中,BSTUN点对点配置了帧中继上的本地确认。在show bstun命令输出中的相关状态在本文中被标记。

注意: 虽然debug bstun packet/eventdebug bsc packet/event 命令不会引起CPU过度利用, logging buffered命令用于复制输出到日志文件。

先决条件

要求

本文档没有任何特定的要求。

使用的组件

本文档中的信息根据Cisco IOS�软件版本12.1(5)。

规则

有关文档规则的详细信息,请参阅 Cisco 技术提示规则

配置

本部分提供有关如何配置本文档所述功能的信息。

注意: 要查找本文档所用命令的其他信息,请使用命令查找工具仅限注册用户)。

网络图

本文档使用以下网络设置:

bstun_p2p_localack_over_fr-01.gif

配置

本文档使用以下配置:

Kilcot
Building configuration 
!
version 12.1
service timestamps debug datetime msec
!
hostname kilcot
!
! 
bstun peer-name 100.1.1.1
bstun protocol-group 72 bsc-local-ack
!
! 
interface Loopback0
ip address 100.1.1.1 255.0.0.0
!
interface Serial0/0
ip address 10.1.1.1 255.0.0.0
encapsulation frame-relay
no ip mroute-cache
frame-relay interface-dlci 16
frame-relay lmi-type ansi
!
interface Serial1/0
no ip address
ip directed-broadcast
encapsulation bstun
no ip mroute-cache
no keepalive
full-duplex
clockrate 9600
bstun group 72
bsc secondary
bstun route all tcp 200.2.2.2
!
!
router rip
network 10.0.0.0
network 100.0.0.0
!
end

Party
Building configuration...

version 12.1
! 
service timestamps debug datetime msec
!
hostname party
!
bstun peer-name 200.2.2.2
bstun protocol-group 72 bsc-local-ack
!
!
interface Loopback0
ip address 200.2.2.2 255.255.255.0
! 
interface Serial0
no ip address
encapsulation bstun
load-interval 30
no keepalive
full-duplex
clockrate 9600
bstun group 72
bsc primary
bstun route all tcp 100.1.1.1
!
interface Serial1
ip address 10.1.1.2 255.0.0.0
encapsulation frame-relay IETF
no ip mroute-cache
frame-relay interface-dlci 17
frame-relay lmi-type ansi
!
!
router rip
network 10.0.0.0
network 200.2.2.0
!
end

验证

本部分提供的信息可帮助您确认您的配置是否可正常运行。

命令输出解释程序工具仅限注册用户)支持某些 show 命令,使用此工具可以查看对 show 命令输出的分析。

  • show bstun

  • show bsc

kilcot#show bsc
BSC local-ack on Serial1/0:
secondary state is CU_Idle.
Control units on this interface:
 
   Poll address: 40. Select address: 60 *CURRENT-CU*
   State is Initializing.
   Tx Counts: 0 frames(total). 0 frames(data). 0 bytes.
   Rx Counts: 3 frames(total). 0 frames(data). 15 bytes.
 
Total Tx Counts: 0 frames(total). 0 frames(data). 0 bytes.
Total Rx Counts: 19 frames(total). 0 frames(data). 59 bytes.

kilcot#show bstun
This peer: 100.1.1.1
 
*Serial1/0  (group 72 [bsc-local-ack])
route transport address         dlci lsap state      rx_pkts tx_pkts   drops
all   TCP       200.2.2.2                 open         1       3        0

party#show bsc
BSC local-ack on Serial0:
primary state is TCU_Polled.
Control units on this interface:
 
   Poll address: 40. Select address: 60 *CURRENT-CU*
   State is Inactive.
   Tx Counts: 126 frames(total). 0 frames(data). 378 bytes.
   Rx Counts: 0 frames(total). 0 frames(data). 0 bytes.
 
Total Tx Counts: 126 frames(total). 0 frames(data). 378 bytes.
Total Rx Counts: 0 frames(total). 0 frames(data). 0 bytes.
 
party#show bstun
This peer: 200.2.2.2
 
*Serial0  (group 72 [bsc-local-ack])
route transport address         dlci lsap state      rx_pkts tx_pkts   drops
all   TCP       100.1.1.1                 open          3       2        0

故障排除

本部分提供的信息可用于对配置进行故障排除。

故障排除命令

debug bstun packet/eventdebug bsc packet/event 输出已被复制到日志文件。当您解释此debug输出时:

  • Serial Data Incoming (SDI) -从同步数据链路控制(SDLC)接口接收的数据包。

  • Network Data Incoming (NDI) - 从广域网解封装的数据包。

注意: 在发出 debug 命令之前,请参阅有关 debug 命令的重要信息

kilcot#show log
Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
    Console logging: disabled
    Monitor logging: level debugging, 0 messages logged
    Buffer logging: level debugging, 5088 messages logged
    Trap logging: level informational, 70 message lines logged
          
Log Buffer (100000 bytes):

Dec 28 09:43:21.748: BSC: Serial1/0: POLLEE-FSM event:  E_LineUp old_state: CU_Down.  new_state: CU_Idle.
Dec 28 09:43:21.756: BSC: Serial1/0: SDI-rx: Data (5 bytes):   40407F7F2D
Dec 28 09:43:36.756: BSTUN bsc-local-ack: Serial1/0 SDI:   Data:   401100
Dec 28 09:43:36.756: BSTUN: Change state for peer  (all[72])200.2.2.2/1976 (closed->opening)
Dec 28 09:43:36.756: BSC: Serial1/0: POLLEE-FSM  event: E_RxEnq 
Dec 28 09:43:36.760: BSTUN: Change state for peer   (all[72])200.2.2.2/1976 (opening->open wait)
Dec 28 09:43:36.764: %BSTUN-6-OPENING: CONN:  opening peer (all[72])200.2.2.2/1976, 3
Dec 28 09:43:36.792: bsttcpd_connect:  Refreshing tcp_encaps for group 72
Dec 28 09:43:36.792: %BSTUN-6-OPENED: CONN:  peer (all[72])200.2.2.2/1976 opened, [previous state open wait]
Dec 28 09:43:36.792: BSTUN: Change state for  peer (all[72])200.2.2.2/1976 (open wait->open)
Dec 28 09:43:36.844: BSTUN bsc-local-ack:  Serial1/0 NDI: Data:   401400
Dec 28 09:43:36.848: BSC: Serial1/0: NDI-rx:  Data (3 bytes):  401400
Dec 28 09:43:37.640: %SYS-5-CONFIG_I:  Configured from console by vty0

party#show log
Syslog logging: enabled (0 messages 
   dropped, 0 flushes, 0 overruns)
    Console logging: disabled
    Monitor logging: level debugging, 114 messages logged
        Logging to: vty2(114)
    Buffer logging: level debugging, 5199 messages logged
    Trap logging: level informational, 79 message lines logged
          
Log Buffer (100000 bytes):

ec 28 09:48:09.816: %BSTUN-6-PASSIVEOPEN:   passive open 100.1.1.1(11017) -> 1976
Dec 28 09:48:09.836: %BSTUN-6-OPENED: PHDR:  peer (all[72])100.1.1.1/1976 opened, [previous state closed]
Dec 28 09:48:09.836: BSTUN: Change state for  peer (all[72])100.1.1.1/1976 (closed->open)
Dec 28 09:48:09.836: BSTUN bsc-local-ack:  Serial0 NDI: Data:   401100
Dec 28 09:48:09.836: BSC: Serial0: NDI-rx:  Data (3 bytes):  401100
Dec 28 09:48:09.836: BSTUN bsc-local-ack:  Serial0 SDI: Data:   401400
Dec 28 09:48:09.836: BSC: Serial0: SDI-tx:  Data (10 bytes):  37FF32323240407F7F2D

相关的思科支持社区讨论

思科支持社区是您提问、解答问题、分享建议以及与工作伙伴协作的论坛。


相关信息


Document ID: 12347