安全与 VPN : IPSec 协商/IKE 协议

多台路由器之间使用 IPSec 上的 GRE 的动态多点 VPN 的配置

2015 年 8 月 28 日 - 机器翻译
其他版本: PDFpdf | 英语 (2015 年 4 月 22 日) | 反馈


目录


简介

动态多点 VPN (DMVPN) 功能可让用户更轻松地调整大型和小型 IPSec VPN,它结合了通用路由封装 (GRE) 隧道、IPSec 加密和下一跳解析协议 (NHRP),使用户能够轻松地通过加密配置文件进行配置,而无需定义静态加密映射和隧道终点动态发现。

先决条件

要求

本文档没有任何特定的要求。

使用的组件

本文档中的信息基于以下软件和硬件版本。

  • Cisco 2691 和 3725 路由器

  • Cisco IOS�软件版本12.3(3)

注意: 只有 Cisco IOS 软件版本 12.2.(2)XK 和 12.2.(13)T 以及更新版本支持多个 IPSec Pass-Through。

show version 命令在路由器上的输出显示如下:

sv9-4#show version
     Cisco Internetwork Operating System Software 
     IOS (tm) 2600 Software (C2691-IK9S-M), Version 12.3(3), 
        RELEASE SOFTWARE (fc2)
     Copyright (c) 1986-2003 by cisco Systems, Inc.
     Compiled Tue 19-Aug-03 05:52 by dchih
     Image text-base: 0x60008954, data-base: 0x61D08000

     ROM: System Bootstrap, Version 12.2(8r)T2, 
        RELEASE SOFTWARE (fc1)

     sv9-4 uptime is 1 hour, 39 minutes
     System returned to ROM by reload
     System image file is "flash:c2691-ik9s-mz.123-3.bin"

     This product contains cryptographic features and is subject 
     to United States and local country laws governing import, 
     export, transfer and use. Delivery of Cisco cryptographic 
     products does not imply third-party authority to import, 
     export, distribute or use encryption. Importers, exporters, 
     distributors and users are responsible for compliance with 
     U.S. and local country laws. By using this product you agree 
     to comply with applicable laws and regulations. If you are 
     unable to comply with U.S. and local laws, return this product 
     immediately.

     A summary of U.S. laws governing Cisco cryptographic products 
     may be found at:
     http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

     If you require further assistance please contact us by sending 
     email to export@cisco.com.

     cisco 2691 (R7000) processor (revision 0.1) 
        with 98304K/32768K bytes of memory.
     Processor board ID JMX0710L5CE
     R7000 CPU at 160Mhz, Implementation 39, 
        Rev 3.3, 256KB L2 Cache
     Bridging software.
     X.25 software, Version 3.0.0.
     SuperLAT software (copyright 1990 by Meridian Technology Corp).
     2 FastEthernet/IEEE 802.3 interface(s)
     2 Serial(sync/async) network interface(s)
     1 ATM network interface(s)
     1 Virtual Private Network (VPN) Module(s)
     DRAM configuration is 64 bits wide with parity disabled.
     55K bytes of non-volatile configuration memory.
     125184K bytes of ATA System CompactFlash (Read/Write)

     Configuration register is 0x2102

本文档中的信息都是基于特定实验室环境中的设备创建的。本文档中使用的所有设备最初均采用原始(默认)配置。如果您是在真实网络上操作,请确保您在使用任何命令前已经了解其潜在影响。

背景理论

该功能适用以下规则。

  • 每个分支具有到集线器而不是到网络中的其他分支的永久性 IPSec 隧道。每个分支注册为 NHRP 服务器的客户端。

  • 当分支需要将数据包发送到另一个分支上的目标(专用)子网时,它会向 NHRP 服务器查询目标分支的实际(外部)地址。

  • 当始发分支学习了目标分支的对等体地址后,它便可以启动连接到目标分支的动态 IPSec 隧道。

  • 分支到分支隧道通过多点 GRE (mGRE) 接口构建。

  • 每当分支之间有流量时,将根据需要建立分支到分支链路。然后,数据包将能绕过集线器,使用分支到分支隧道。

以下定义适用于规则集。

  • NHRP —集线器的客户端和服务器协议服务器和spoke是客户端。集线器维护着一个 NHRP 数据库,其中包含每个分支的公共接口地址。每个分支在启动时注册自己的实际地址,并向 NHRP 数据库查询目标分支的实际地址,以便构建直接隧道。

  • mGRE 隧道接口 — 允许单个 GRE 接口支持多个 IPSec 隧道,并简化配置的大小和复杂性。

注意: 若分支到分支隧道的非活动时间超过了预先配置的非活动时间,则路由器将切断这些隧道,以节约资源(IPSec 安全连接 [SA])。

注意: 流量配置文件应当遵循 80/20 法则:80% 的数据流由分支到集线器数据流组成,而 20% 的数据流由分支到分支数据流组成。

规则

有关文档规则的详细信息,请参阅 Cisco 技术提示规则

配置

本部分提供有关如何配置本文档所述功能的信息。

注意: 要查找本文档所用命令的其他信息,请使用命令查找工具仅限注册用户)。

网络图

本文档使用下图所示的网络设置。

/image/gif/paws/29240/dcmvpn.gif

配置

本文档使用如下所示的配置。

中心路由器 (sv9-2) 配置
sv9-2#show run
Building configuration...

Current configuration : 1827 bytes
!
version 12.3
service config
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname sv9-2
!
boot-start-marker
boot-end-marker
!
enable password cisco
!
no aaa new-model
ip subnet-zero
!
!
no ip domain lookup
!
ip ssh break-string
!

!--- Create an Internet Security Association and Key Management 
!--- Protocol (ISAKMP) policy for Phase 1 negotiations.

!
crypto isakmp policy 10
hash md5
authentication pre-share

!--- Add dynamic pre-shared keys for all the remote VPN 
!--- routers.

crypto isakmp key cisco123 address 0.0.0.0 0.0.0.0
!

!--- Create the Phase 2 policy for actual data encryption.

crypto ipsec transform-set strong esp-3des esp-md5-hmac 
!

!--- Create an IPSec profile to be applied dynamically to the 
!--- GRE over IPSec tunnels.

crypto ipsec profile cisco
set security-association lifetime seconds 120
set transform-set strong 
!
!
!
!
!
!
!
!
!
! 
!
no voice hpi capture buffer
no voice hpi capture destination 
!
!
!
!
!
!
!

!--- Create a GRE tunnel template which will be applied to 
!--- all the dynamically created GRE tunnels.

interface Tunnel0
ip address 192.168.1.1 255.255.255.0
no ip redirects
ip mtu 1440
ip nhrp authentication cisco123
ip nhrp map multicast dynamic
ip nhrp network-id 1
no ip split-horizon eigrp 90
no ip next-hop-self eigrp 90
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 0
tunnel protection ipsec profile cisco
!

!--- This is the outbound interface.

interface FastEthernet0/0
ip address 209.168.202.225 255.255.255.0
duplex auto
speed auto
!

!--- This is the inbound interface.

interface FastEthernet0/1
ip address 1.1.1.1 255.255.255.0
duplex auto
speed auto
!
interface BRI1/0
no ip address
shutdown
!
interface BRI1/1
no ip address
shutdown
!
interface BRI1/2
no ip address
shutdown 
!
interface BRI1/3
no ip address
shutdown
!

!--- Enable a routing protocol to send and receive 
!--- dynamic updates about the private networks.

router eigrp 90
network 1.1.1.0 0.0.0.255
network 192.168.1.0
no auto-summary
!
ip http server
no ip http secure-server
ip classless
ip route 0.0.0.0 0.0.0.0 209.168.202.226
!
!
!
!
!
!
!
!
! 
!
!
line con 0
exec-timeout 0 0
transport preferred all
transport output all
escape-character 27
line aux 0
transport preferred all
transport output all
line vty 0 4
password cisco
login
transport preferred all
transport input all
transport output all
!
!
end

分支 #1 (sv9-3) 配置
sv9-3#show run
Building configuration...

Current configuration : 1993 bytes
!
version 12.3
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname sv9-3
!
boot-start-marker
boot system flash:c3725-ik9s-mz.123-3.bin
boot-end-marker
!
!
no aaa new-model
ip subnet-zero
!
!
no ip domain lookup
!
ip ssh break-string 
!
! 

!--- Create an ISAKMP policy for Phase 1 negotiations.

crypto isakmp policy 10
hash md5
authentication pre-share

!--- Add dynamic pre-shared keys for all the remote VPN 
!--- routers and the hub router.

crypto isakmp key cisco123 address 0.0.0.0 0.0.0.0
!
!

!--- Create the Phase 2 policy for actual data encryption.

crypto ipsec transform-set strong esp-3des esp-md5-hmac 
!

!--- Create an IPSec profile to be applied dynamically to 
!--- the GRE over IPSec tunnels.

crypto ipsec profile cisco
set security-association lifetime seconds 120
set transform-set strong 
!
!
!
!
!
!
!
!
!
!
! 
no voice hpi capture buffer
no voice hpi capture destination 
!
!
fax interface-type fax-mail
!
!
!
!
!

!--- Create a GRE tunnel template to be applied to 
!--- all the dynamically created GRE tunnels.

interface Tunnel0
ip address 192.168.1.2 255.255.255.0
no ip redirects
ip mtu 1440
ip nhrp authentication cisco123
ip nhrp map multicast dynamic
ip nhrp map 192.168.1.1 209.168.202.225
ip nhrp map multicast 209.168.202.225
ip nhrp network-id 1
ip nhrp nhs 192.168.1.1
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 0
tunnel protection ipsec profile cisco
!

!--- This is the outbound interface.

interface FastEthernet0/0
ip address 209.168.202.131 255.255.255.0
duplex auto
speed auto
!

!--- This is the inbound interface.

interface FastEthernet0/1
ip address 2.2.2.2 255.255.255.0
duplex auto
speed auto
!
interface BRI1/0
no ip address
shutdown
!
interface BRI1/1
no ip address
shutdown
! 
interface BRI1/2
no ip address
shutdown
!
interface BRI1/3
no ip address
shutdown
!

!--- Enable a routing protocol to send and receive 
!--- dynamic updates about the private networks.

router eigrp 90
network 2.2.2.0 0.0.0.255
network 192.168.1.0
no auto-summary
!
ip http server
no ip http secure-server
ip classless
ip route 0.0.0.0 0.0.0.0 209.168.202.225
ip route 3.3.3.0 255.255.255.0 Tunnel0
!
!
!
!
! 
!
!
!
dial-peer cor custom
!
!
!
!
!
line con 0
exec-timeout 0 0
transport preferred all
transport output all
escape-character 27
line aux 0
transport preferred all
transport output all
line vty 0 4
login
transport preferred all
transport input all
transport output all
! 
!
end

分支 #2 (sv9-4) 配置
sv9-4#show run
Building configuration...

Current configuration : 1994 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname sv9-4
!
boot-start-marker
boot system flash:c2691-ik9s-mz.123-3.bin
boot-end-marker
!
!
no aaa new-model
ip subnet-zero
!
!
no ip domain lookup
!
ip ssh break-string 
!
! 
!

!--- Create an ISAKMP policy for Phase 1 negotiations.

crypto isakmp policy 10
hash md5
authentication pre-share

!--- Add dynamic pre-shared keys for all the remote VPN 
!--- routers and the hub router.

crypto isakmp key cisco123 address 0.0.0.0 0.0.0.0
!
!

!--- Create the Phase 2 policy for actual data encryption.

crypto ipsec transform-set strong esp-3des esp-md5-hmac 
!

!--- Create an IPSec profile to be applied dynamically to 
!--- the GRE over IPSec tunnels.

crypto ipsec profile cisco
set security-association lifetime seconds 120
set transform-set strong 
!
!
!
!
!
!
!
!
!
!
! 
no voice hpi capture buffer
no voice hpi capture destination 
!
!
!
!
!
!
!

!--- Create a GRE tunnel template to be applied to 
!--- all the dynamically created GRE tunnels.

interface Tunnel0
ip address 192.168.1.3 255.255.255.0
no ip redirects
ip mtu 1440
ip nhrp authentication cisco123
ip nhrp map multicast dynamic
ip nhrp map 192.168.1.1 209.168.202.225
ip nhrp map multicast 209.168.202.225
ip nhrp network-id 1
ip nhrp nhs 192.168.1.1
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 0
tunnel protection ipsec profile cisco
!

!--- This is the outbound interface.

interface FastEthernet0/0
ip address 209.168.202.130 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
clockrate 2000000
no fair-queue
!

!--- This is the inbound interface.

interface FastEthernet0/1
ip address 3.3.3.3 255.255.255.0
duplex auto
speed auto
!
interface Serial0/1
no ip address
shutdown 
clockrate 2000000
!
interface ATM1/0
no ip address
shutdown
no atm ilmi-keepalive
!

!--- Enable a routing protocol to send and receive 
!--- dynamic updates about the private networks.

router eigrp 90
network 3.3.3.0 0.0.0.255
network 192.168.1.0
no auto-summary
!
ip http server
no ip http secure-server
ip classless
ip route 2.2.2.0 255.255.255.0 Tunnel0
ip route 0.0.0.0 0.0.0.0 209.168.202.225
!
!
!
!
!
!
! 
!
dial-peer cor custom
!
!
!
!
!
line con 0
exec-timeout 0 0
transport preferred all
transport output all
escape-character 27
line aux 0
transport preferred all
transport output all
line vty 0 4
password cisco
login
transport preferred all
transport input all
transport output all
!
! 
end

验证

本部分所提供的信息可用于确认您的配置是否正常工作。

命令输出解释程序工具仅限注册用户)支持某些 show 命令,使用此工具可以查看对 show 命令输出的分析。

  • show crypto engine connection active — 按 SA 显示总加密和解密。

  • show crypto ipsec sa — 显示有关活动隧道的统计数据。

  • show crypto isakmp sa — 显示 ISAKMP SA 的状态。

故障排除

本部分提供的信息可用于对配置进行故障排除。

DMVPN 隧道间歇性抖动

问题

DMVPN 隧道间歇性抖动。

解决方案

当 DMVPN 隧道抖动时,请检查路由器之间的邻居关系,因为路由器之间结邻的问题可能会造成 DMVPN 隧道抖动。要解决此问题,请确保路由器之间始终保持良好的邻居关系。

故障排除命令

注意: 在发出 debug 命令之前,请参阅有关 Debug 命令的重要信息

  • debug crypto ipsec — 显示 IPSec 事件。

  • debug crypto isakmp — 显示有关 Internet 密钥交换 (IKE) 事件的消息。

  • debug crypto engine - 显示来自加密引擎的信息。

有关 IPsec 故障排除的其他信息,请参阅 IP 安全故障排除 - 了解和使用 debug 命令

调试输出示例

NHRP debug

以下 debug 输出显示了 NHRP 请求和 NHRP 解析响应。这些 debug 从分支 sv9-4 和 sv9-3 以及集线器 sv9-2 捕获而来。

sv9-4#show debug
NHRP:
NHRP protocol debugging is on

sv9-4#ping 2.2.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
sv9-4#
*Mar 1 02:06:01.667: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
*Mar 1 02:06:01.671: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
*Mar 1 02:06:01.675: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
*Mar 1 02:06:01.679: NHRP: Encapsulation succeeded. 
   Tunnel IP addr 209.168.202.225
*Mar 1 02:06:01.679: NHRP: Send Resolution Request via Tunnel0, 
   packet size: 84
*Mar 1 02:06:01.679: src: 192.168.1.3, dst: 192.168.1.1
*Mar 1 02:06:01.679: NHRP: 84 bytes out Tunnel0 
*Mar 1 02:06:01.679: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
*Mar 1 02:06:01.683: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
*Mar 1 02:06:03.507: NHRP: Encapsulation succeeded. 
   Tunnel IP addr 209.168.202.225
*Mar 1 02:06:03.507: NHRP: Send Resolution Request via Tunnel0, 
   packet size: 84
*Mar 1 02:06:03.507: src: 192.168.1.3, dst: 192.168.1.1
*Mar 1 02:06:03.507: NHRP: 84 bytes out Tunnel0 
*Mar 1 02:06:03.511: NHRP: Receive Resolution Reply via Tunnel0, 
   packet size: 132
*Mar 1 02:06:03.511: NHRP: netid_in = 0, to_us = 1
*Mar 1 02:06:03.511: NHRP: No need to delay processing of resolution
   event nbma src:209.168.202.130 nbma dst:209.168.202.131

sv9-3# 
05:31:12: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
05:31:12: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
05:31:12: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
05:31:12: NHRP: Encapsulation succeeded. Tunnel IP addr 209.168.202.225
05:31:12: NHRP: Send Resolution Request via Tunnel0, packet size: 84
05:31:12: src: 192.168.1.2, dst: 192.168.1.1
05:31:12: NHRP: 84 bytes out Tunnel0 
05:31:12: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
05:31:12: NHRP: Receive Resolution Request via Tunnel0, packet size: 104
05:31:12: NHRP: netid_in = 1, to_us = 0
05:31:12: NHRP: Delaying resolution request nbma src:209.168.202.131 
   nbma dst:209.168.202.130 reason:IPSEC-IFC: need to wait for IPsec SAs.
05:31:12: NHRP: Receive Resolution Reply via Tunnel0, packet size: 112
05:31:12: NHRP: netid_in = 0, to_us = 1
05:31:12: NHRP: Resolution request is already being processed (delayed).
05:31:12: NHRP: Resolution Request not queued. 
   Already being processed (delayed).
05:31:12: NHRP: Sending packet to NHS 192.168.1.1 on Tunnel0
05:31:13: NHRP: Process delayed resolution request src:192.168.1.3 
   dst:2.2.2.2
05:31:13: NHRP: No need to delay processing of resolution event 
   nbma src:209.168.202.131 nbma dst:209.168.202.130

sv9-2#
*Mar 1 06:03:40.174: NHRP: Forwarding packet within same fabric 
   Tunnel0 -> Tunnel0
*Mar 1 06:03:40.174: NHRP: Forwarding packet within same fabric 
   Tunnel0 -> Tunnel0
*Mar 1 06:03:40.178: NHRP: Forwarding packet within same fabric 
   Tunnel0 -> Tunnel0
*Mar 1 06:03:40.182: NHRP: Receive Resolution Request via Tunnel0, 
   packet size: 84
*Mar 1 06:03:40.182: NHRP: netid_in = 1, to_us = 0
*Mar 1 06:03:40.182: NHRP: No need to delay processing of resolution 
   event nbma src:209.168.202.225 nbma dst:209.168.202.130
*Mar 1 06:03:40.182: NHRP: nhrp_rtlookup yielded Tunnel0
*Mar 1 06:03:40.182: NHRP: netid_out 1, netid_in 1
*Mar 1 06:03:40.182: NHRP: nhrp_cache_lookup_comp returned 0x0
*Mar 1 06:03:40.182: NHRP: calling nhrp_forward
*Mar 1 06:03:40.182: NHRP: Encapsulation succeeded. 
   Tunnel IP addr 209.168.202.131
*Mar 1 06:03:40.182: NHRP: Forwarding Resolution Request via Tunnel0, 
   packet size: 104
*Mar 1 06:03:40.182: src: 192.168.1.1, dst: 2.2.2.2
*Mar 1 06:03:40.182: NHRP: 104 bytes out Tunnel0 
*Mar 1 06:03:40.182: NHRP: Forwarding packet within same fabric 
   Tunnel0 -> Tunnel0
*Mar 1 06:03:40.182: NHRP: Receive Resolution Request via Tunnel0, 
   packet size: 84
*Mar 1 06:03:40.182: NHRP: netid_in = 1, to_us = 0
*Mar 1 06:03:40.182: NHRP: No need to delay processing of resolution 
   event nbma src:209.168.202.225 nbma dst:209.168.202.131
*Mar 1 06:03:40.182: NHRP: nhrp_rtlookup yielded Tunnel0
*Mar 1 06:03:40.182: NHRP: netid_out 1, netid_in 1
*Mar 1 06:03:40.182: NHRP: nhrp_cache_lookup_comp returned 0x63DE9498
*Mar 1 06:03:40.182: NHRP: Encapsulation succeeded. 
   Tunnel IP addr 209.168.202.131
*Mar 1 06:03:40.182: NHRP: Send Resolution Reply via Tunnel0, 
   packet size: 112
*Mar 1 06:03:40.186: src: 192.168.1.1, dst: 192.168.1.2
*Mar 1 06:03:40.186: NHRP: 112 bytes out Tunnel0 
*Mar 1 06:03:40.186: NHRP: Forwarding packet within same fabric 
   Tunnel0 -> Tunnel0
*Mar 1 06:03:42.010: NHRP: Receive Resolution Request via Tunnel0, 
   packet size: 84
*Mar 1 06:03:42.010: NHRP: netid_in = 1, to_us = 0
*Mar 1 06:03:42.010: NHRP: No need to delay processing of resolution 
   event nbma src:209.168.202.225 nbma dst:209.168.202.130

ISAKMP 和 IPSec 协商调试

以下 debug 输出显示了 ISAKMP 和 IPSec 协商。这些 debug 从分支 sv9-4 和 sv9-3 捕获而来。

sv9-4#ping 2.2.2.2 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
sv9-4#
*Mar 1 02:25:37.107: ISAKMP (0:0): received packet from 209.168.202.131 
   dport 500 sport 500 Global (N) NEW SA
*Mar 1 02:25:37.107: ISAKMP: local port 500, remote port 500
*Mar 1 02:25:37.107: ISAKMP: insert sa successfully sa = 63B38288
*Mar 1 02:25:37.107: ISAKMP (0:12): Input = IKE_MESG_FROM_PEER, 
   IKE_MM_EXCH
*Mar 1 02:25:37.107: ISAKMP (0:12): Old State = IKE_READY 
   New State = IKE_R_MM1 

*Mar 1 02:25:37.107: ISAKMP (0:12): processing SA payload. 
   message ID = 0
*Mar 1 02:25:37.107: ISAKMP (0:12): processing vendor id payload
*Mar 1 02:25:37.107: ISAKMP (0:12): vendor ID seems Unity/DPD but 
   major 157 mismatch
*Mar 1 02:25:37.107: ISAKMP (0:12): vendor ID is NAT-T v3
*Mar 1 02:25:37.107: ISAKMP (0:12): processing vendor id payload
*Mar 1 02:25:37.107: ISAKMP (0:12): vendor ID seems Unity/DPD but 
   major 123 mismatch
*Mar 1 02:25:37.107: ISAKMP (0:12): vendor ID is NAT-T v2
*Mar 1 02:25:37.107: ISAKMP: Looking for a matching key for 
   209.168.202.131 in default : success
*Mar 1 02:25:37.107: ISAKMP (0:12): found peer pre-shared key 
   matching 209.168.202.131
*Mar 1 02:25:37.107: ISAKMP (0:12) local preshared key found
*Mar 1 02:25:37.107: ISAKMP : Scanning profiles for xauth ...
*Mar 1 02:25:37.107: ISAKMP (0:12): Checking ISAKMP transform 1 
   against priority 10 policy
*Mar 1 02:25:37.107: ISAKMP: encryption DES-CBC
*Mar 1 02:25:37.107: ISAKMP: hash MD5
*Mar 1 02:25:37.107: ISAKMP: default group 1
*Mar 1 02:25:37.107: ISAKMP: auth pre-share
*Mar 1 02:25:37.107: ISAKMP: life type in seconds
*Mar 1 02:25:37.107: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80 
*Mar 1 02:25:37.107: ISAKMP (0:12): atts are acceptable. 
   Next payload is 0
*Mar 1 02:25:37.115: ISAKMP (0:12): processing vendor id payload
*Mar 1 02:25:37.115: ISAKMP (0:12): vendor ID seems Unity/DPD but 
   major 157 mismatch
*Mar 1 02:25:37.115: ISAKMP (0:12): vendor ID is NAT-T v3
*Mar 1 02:25:37.115: ISAKMP (0:12): processing vendor id payload
*Mar 1 02:25:37.115: ISAKMP (0:12): vendor ID seems Unity/DPD but 
   major 123 mismatch
*Mar 1 02:25:37.115: ISAKMP (0:12): vendor ID is NAT-T v2
*Mar 1 02:25:37.115: ISAKMP (0:12): Input = IKE_MESG_INTERNAL, 
   IKE_PROCESS_MAIN_MODE
*Mar 1 02:25:37.115: ISAKMP (0:12): Old State = IKE_R_MM1 
   New State = IKE_R_MM1 

*Mar 1 02:25:37.115: ISAKMP (0:12): constructed NAT-T vendor-03 ID
*Mar 1 02:25:37.115: ISAKMP (0:12): sending packet to 209.168.202.131 
   my_port 500 peer_port 500 (R) MM_SA_SETUP
*Mar 1 02:25:37.115: ISAKMP (0:12): Input = IKE_MESG_INTERNAL, 
   IKE_PROCESS_COMPLETE
*Mar 1 02:25:37.115: ISAKMP (0:12): Old State = IKE_R_MM1 
   New State = IKE_R_MM2 

*Mar 1 02:25:37.123: ISAKMP (0:12): received packet from 209.168.202.131 
   dport 500 sport 500 Global (R) MM_SA_SETUP
*Mar 1 02:25:37.123: ISAKMP (0:12): Input = IKE_MESG_FROM_PEER, 
   IKE_MM_EXCH
*Mar 1 02:25:37.123: ISAKMP (0:12): Old State = IKE_R_MM2 
   New State = IKE_R_MM3 

*Mar 1 02:25:37.123: ISAKMP (0:12): processing KE payload. 
   message ID = 0
*Mar 1 02:25:37.131: ISAKMP (0:12): processing NONCE payload. 
   message ID = 0
*Mar 1 02:25:37.131: ISAKMP: Looking for a matching key for 
   209.168.202.131 in default : success
*Mar 1 02:25:37.131: ISAKMP (0:12): found peer pre-shared key matching  
   209.168.202.131
*Mar 1 02:25:37.131: ISAKMP: Looking for a matching key for  
   209.168.202.131 in default : success
*Mar 1 02:25:37.131: ISAKMP (0:12): found peer pre-shared key  
   matching 209.168.202.131
*Mar 1 02:25:37.135: ISAKMP (0:12): SKEYID state generated
*Mar 1 02:25:37.135: ISAKMP (0:12): processing vendor id payload
*Mar 1 02:25:37.135: ISAKMP (0:12): vendor ID is Unity
*Mar 1 02:25:37.135: ISAKMP (0:12): processing vendor id payload
*Mar 1 02:25:37.135: ISAKMP (0:12): vendor ID is DPD
*Mar 1 02:25:37.135: ISAKMP (0:12): processing vendor id payload
*Mar 1 02:25:37.135: ISAKMP (0:12): speaking to another IOS box!
*Mar 1 02:25:37.135: ISAKMP:received payload type 17
*Mar 1 02:25:37.135: ISAKMP:received payload type 17
*Mar 1 02:25:37.135: ISAKMP (0:12): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_MAIN_MODE
*Mar 1 02:25:37.135: ISAKMP (0:12): Old State = IKE_R_MM3  
   New State = IKE_R_MM3 

*Mar 1 02:25:37.135: ISAKMP (0:12): sending packet to 209.168.202.131  
   my_port 500 peer_port 500 (R) MM_KEY_EXCH
*Mar 1 02:25:37.135: ISAKMP (0:12): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_COMPLETE
*Mar 1 02:25:37.135: ISAKMP (0:12): Old State = IKE_R_MM3  
   New State = IKE_R_MM4 

*Mar 1 02:25:37.147: ISAKMP (0:12): received packet from 209.168.202.131  
   dport 500 sport 500 Global (R) MM_KEY_EXCH
*Mar 1 02:25:37.151: ISAKMP (0:12): Input = IKE_MESG_FROM_PEER,  
   IKE_MM_EXCH
*Mar 1 02:25:37.151: ISAKMP (0:12): Old State = IKE_R_MM4  
   New State = IKE_R_MM5 

*Mar 1 02:25:37.151: ISAKMP (0:12): processing ID payload.  
   message ID = 0
*Mar 1 02:25:37.151: ISAKMP (0:12): peer matches *none* of the profiles
*Mar 1 02:25:37.151: ISAKMP (0:12): processing HASH payload.  
   message ID = 0
*Mar 1 02:25:37.151: ISAKMP (0:12): processing NOTIFY INITIAL_CONTACT  
   protocol 1 spi 0, message ID = 0, sa = 63B38288
*Mar 1 02:25:37.151: ISAKMP (0:12): Process initial contact,  
   bring down existing phase 1 and 2 SA's with local 209.168.202.130  
   remote 209.168.202.131 remote port 500
*Mar 1 02:25:37.151: ISAKMP (0:12): SA has been authenticated with  
   209.168.202.131
*Mar 1 02:25:37.151: ISAKMP (0:12): peer matches *none* of the profiles
*Mar 1 02:25:37.151: ISAKMP (0:12): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_MAIN_MODE
*Mar 1 02:25:37.151: ISAKMP (0:12): Old State = IKE_R_MM5  
   New State = IKE_R_MM5 

*Mar 1 02:25:37.151: IPSEC(key_engine): got a queue event...
*Mar 1 02:25:37.151: ISAKMP (0:12): SA is doing pre-shared key  
   authentication using id type ID_IPV4_ADDR
*Mar 1 02:25:37.151: ISAKMP (12): ID payload
next-payload : 8
type : 1
addr : 209.168.202.130
protocol : 17
port : 500
length : 8
*Mar 1 02:25:37.151: ISAKMP (12): Total payload length: 12
*Mar 1 02:25:37.155: ISAKMP (0:12): sending packet to 209.168.202.131  
   my_port 500 peer_port 500 (R) MM_KEY_EXCH
*Mar 1 02:25:37.155: ISAKMP (0:12): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_COMPLETE
*Mar 1 02:25:37.155: ISAKMP (0:12): Old State = IKE_R_MM5  
   New State = IKE_P1_COMPLETE 

*Mar 1 02:25:37.155: ISAKMP (0:12): Input = IKE_MESG_INTERNAL,  
   IKE_PHASE1_COMPLETE
*Mar 1 02:25:37.155: ISAKMP (0:12): Old State = IKE_P1_COMPLETE  
   New State = IKE_P1_COMPLETE 

*Mar 1 02:25:37.159: ISAKMP (0:12): received packet from 209.168.202.131  
   dport 500 sport 500 Global (R) QM_IDLE 
*Mar 1 02:25:37.159: ISAKMP: set new node -1682446278 to QM_IDLE 
*Mar 1 02:25:37.159: ISAKMP (0:12): processing HASH payload.  
   message ID = -1682446278
*Mar 1 02:25:37.159: ISAKMP (0:12): processing SA payload.  
   message ID = -1682446278
*Mar 1 02:25:37.159: ISAKMP (0:12): Checking IPSec proposal 1
*Mar 1 02:25:37.159: ISAKMP: transform 1, ESP_3DES
*Mar 1 02:25:37.159: ISAKMP: attributes in transform:
*Mar 1 02:25:37.159: ISAKMP: encaps is 1
*Mar 1 02:25:37.159: ISAKMP: SA life type in seconds
*Mar 1 02:25:37.159: ISAKMP: SA life duration (basic) of 120
*Mar 1 02:25:37.159: ISAKMP: SA life type in kilobytes
*Mar 1 02:25:37.159: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0 
*Mar 1 02:25:37.159: ISAKMP: authenticator is HMAC-MD5
*Mar 1 02:25:37.159: ISAKMP (0:12): atts are acceptable.
*Mar 1 02:25:37.163: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 209.168.202.130, remote= 209.168.202.131, 
local_proxy= 209.168.202.130/255.255.255.255/47/0 (type=1), 
remote_proxy= 209.168.202.131/255.255.255.255/47/0 (type=1),
protocol= ESP, transform= esp-3des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x2
*Mar 1 02:25:37.163: IPSEC(kei_proxy): head = Tunnel0-head-0,  
   map->ivrf = , kei->ivrf = 
*Mar 1 02:25:37.163: IPSEC(kei_proxy): head = Tunnel0-head-0,  
   map->ivrf = , kei->ivrf = 
*Mar 1 02:25:37.163: ISAKMP (0:12): processing NONCE payload.  
   message ID = -1682446278
*Mar 1 02:25:37.163: ISAKMP (0:12): processing ID payload.  
   message ID = -1682446278
*Mar 1 02:25:37.163: ISAKMP (0:12): processing ID payload.  
   message ID = -1682446278
*Mar 1 02:25:37.163: ISAKMP (0:12): asking for 1 spis from ipsec
*Mar 1 02:25:37.163: ISAKMP (0:12): Node -1682446278,  
   Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Mar 1 02:25:37.163: ISAKMP (0:12): Old State = IKE_QM_READY  
   New State = IKE_QM_SPI_STARVE
*Mar 1 02:25:37.163: IPSEC(key_engine): got a queue event...
*Mar 1 02:25:37.163: IPSEC(spi_response): getting spi 3935077313  
   for SA from 209.168.202.130 to 209.168.202.131 for prot 3
*Mar 1 02:25:37.163: ISAKMP: received ke message (2/1)
*Mar 1 02:25:37.415: ISAKMP (0:12): sending packet to 209.168.202.131  
   my_port 500 peer_port 500 (R) QM_IDLE 
*Mar 1 02:25:37.415: ISAKMP (0:12): Node -1682446278,  
   Input = IKE_MESG_FROM_IPSEC, IKE_SPI_REPLY
*Mar 1 02:25:37.415: ISAKMP (0:12): Old State = IKE_QM_SPI_STARVE  
   New State = IKE_QM_R_QM2
*Mar 1 02:25:37.427: ISAKMP (0:12): received packet from  
   209.168.202.131 dport 500 sport 500 Global (R) QM_IDLE 
*Mar 1 02:25:37.439: ISAKMP (0:12): Creating IPSec SAs
*Mar 1 02:25:37.439: inbound SA from 209.168.202.131 to  
   209.168.202.130 (f/i) 0/ 0
(proxy 209.168.202.131 to 209.168.202.130)
*Mar 1 02:25:37.439: has spi 0xEA8C83C1 and conn_id 5361 and flags 2
*Mar 1 02:25:37.439: lifetime of 120 seconds
*Mar 1 02:25:37.439: lifetime of 4608000 kilobytes
*Mar 1 02:25:37.439: has client flags 0x0
*Mar 1 02:25:37.439: outbound SA from 209.168.202.130 to  
   209.168.202.131 (f/i) 0/ 0 (proxy 209.168.202.130 to 209.168.202.131)
*Mar 1 02:25:37.439: has spi 1849847934 and conn_id 5362 and flags A
*Mar 1 02:25:37.439: lifetime of 120 seconds
*Mar 1 02:25:37.439: lifetime of 4608000 kilobytes
*Mar 1 02:25:37.439: has client flags 0x0
*Mar 1 02:25:37.439: ISAKMP (0:12): deleting node -1682446278 error  
   FALSE reason "quick mode done (await)"
*Mar 1 02:25:37.439: ISAKMP (0:12): Node -1682446278,  
   Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Mar 1 02:25:37.439: ISAKMP (0:12): Old State = IKE_QM_R_QM2  
   New State = IKE_QM_PHASE2_COMPLETE
*Mar 1 02:25:37.439: IPSEC(key_engine): got a queue event...
*Mar 1 02:25:37.439: IPSEC(initialize_sas): ,
(key eng. msg.) INBOUND local= 209.168.202.130, remote= 209.168.202.131, 
local_proxy= 209.168.202.130/0.0.0.0/47/0 (type=1), 
remote_proxy= 209.168.202.131/0.0.0.0/47/0 (type=1),
protocol= ESP, transform= esp-3des esp-md5-hmac , 
lifedur= 120s and 4608000kb, 
spi= 0xEA8C83C1(3935077313), conn_id= 5361, keysize= 0, flags= 0x2
*Mar 1 02:25:37.439: IPSEC(initialize_sas): ,
(key eng. msg.) OUTBOUND local= 209.168.202.130, remote= 209.168.202.131, 
local_proxy= 209.168.202.130/0.0.0.0/47/0 (type=1), 
remote_proxy= 209.168.202.131/0.0.0.0/47/0 (type=1),
protocol= ESP, transform= esp-3des esp-md5-hmac , 
lifedur= 120s and 4608000kb, 
spi= 0x6E42707E(1849847934), conn_id= 5362, keysize= 0, flags= 0xA
*Mar 1 02:25:37.439: IPSEC(kei_proxy): head = Tunnel0-head-0,  
   map->ivrf = , kei->ivrf = 
*Mar 1 02:25:37.439: IPSEC(kei_proxy): head = Tunnel0-head-0,  
   map->ivrf = , kei->ivrf = 
*Mar 1 02:25:37.439: IPSEC(add mtree): src 209.168.202.130,  
   dest 209.168.202.131, dest_port 0

*Mar 1 02:25:37.439: IPSEC(create_sa): sa created,
(sa) sa_dest= 209.168.202.130, sa_prot= 50, 
sa_spi= 0xEA8C83C1(3935077313), 
sa_trans= esp-3des esp-md5-hmac , sa_conn_id= 5361
*Mar 1 02:25:37.439: IPSEC(create_sa): sa created,
(sa) sa_dest= 209.168.202.131, sa_prot= 50, 
sa_spi= 0x6E42707E(1849847934), 
sa_trans= esp-3des esp-md5-hmac , sa_conn_id= 5362
sv9-4#
*Mar 1 02:25:55.183: ISAKMP (0:10): purging node 180238748
*Mar 1 02:25:55.323: ISAKMP (0:10): purging node -1355110639
sv9-4#
 
sv9-3#

05:50:48: ISAKMP: received ke message (1/1)
05:50:48: ISAKMP (0:0): SA request profile is (NULL)
05:50:48: ISAKMP: local port 500, remote port 500
05:50:48: ISAKMP: set new node 0 to QM_IDLE 
05:50:48: ISAKMP: insert sa successfully sa = 62DB93D0
05:50:48: ISAKMP (0:26): Can not start Aggressive mode, trying Main mode.
05:50:48: ISAKMP: Looking for a matching key for 209.168.202.130  
   in default : success
05:50:48: ISAKMP (0:26): found peer pre-shared key  
   matching 209.168.202.130
05:50:48: ISAKMP (0:26): constructed NAT-T vendor-03 ID
05:50:48: ISAKMP (0:26): constructed NAT-T vendor-02 ID
05:50:48: ISAKMP (0:26): Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
05:50:48: ISAKMP (0:26): Old State = IKE_READY New State = IKE_I_MM1 

05:50:48: ISAKMP (0:26): beginning Main Mode exchange
05:50:48: ISAKMP (0:26): sending packet to 209.168.202.130 my_port 500  
   peer_port 500 (I) MM_NO_STATE
05:50:48: ISAKMP (0:26): received packet from 209.168.202.130 dport 500  
   sport 500 Global (I) MM_NO_STATE
05:50:48: ISAKMP (0:26): Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM1 New State = IKE_I_MM2 

05:50:48: ISAKMP (0:26): processing SA payload. message ID = 0
05:50:48: ISAKMP (0:26): processing vendor id payload
05:50:48: ISAKMP (0:26): vendor ID seems Unity/DPD  
   but major 157 mismatch
05:50:48: ISAKMP (0:26): vendor ID is NAT-T v3
05:50:48: ISAKMP: Looking for a matching key for 209.168.202.130  
   in default : success
05:50:48: ISAKMP (0:26): found peer pre-shared key  
   matching 209.168.202.130
05:50:48: ISAKMP (0:26) local preshared key found
05:50:48: ISAKMP : Scanning profiles for xauth ...
05:50:48: ISAKMP (0:26): Checking ISAKMP transform 1 against  
   priority 10 policy
05:50:48: ISAKMP: encryption DES-CBC
05:50:48: ISAKMP: hash MD5
05:50:48: ISAKMP: default group 1
05:50:48: ISAKMP: auth pre-share
05:50:48: ISAKMP: life type in seconds
05:50:48: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80 
05:50:48: ISAKMP (0:26): atts are acceptable. Next payload is 0
05:50:48: ISAKMP (0:26): processing vendor id payload
05:50:48: ISAKMP (0:26): vendor ID seems Unity/DPD  
   but major 157 mismatch
05:50:48: ISAKMP (0:26): vendor ID is NAT-T v3
05:50:48: ISAKMP (0:26): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_MAIN_MODE
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM2  
   New State = IKE_I_MM2 

05:50:48: ISAKMP (0:26): sending packet to 209.168.202.130 my_port 500  
   peer_port 500 (I) MM_SA_SETUP
05:50:48: ISAKMP (0:26): Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM2 New State = IKE_I_MM3 

05:50:48: ISAKMP (0:26): received packet from 209.168.202.130 dport 500  
   sport 500 Global (I) MM_SA_SETUP
05:50:48: ISAKMP (0:26): Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM3 New State = IKE_I_MM4 

05:50:48: ISAKMP (0:26): processing KE payload. message ID = 0
05:50:48: ISAKMP (0:26): processing NONCE payload. message ID = 0
05:50:48: ISAKMP: Looking for a matching key for 209.168.202.130  
   in default : success
05:50:48: ISAKMP (0:26): found peer pre-shared key  
   matching 209.168.202.130
05:50:48: ISAKMP: Looking for a matching key for 209.168.202.130  
   in default : success
05:50:48: ISAKMP (0:26): found peer pre-shared key  
   matching 209.168.202.130
05:50:48: ISAKMP (0:26): SKEYID state generated
05:50:48: ISAKMP (0:26): processing vendor id payload
05:50:48: ISAKMP (0:26): vendor ID is Unity
05:50:48: ISAKMP (0:26): processing vendor id payload
05:50:48: ISAKMP (0:26): vendor ID is DPD
05:50:48: ISAKMP (0:26): processing vendor id payload
05:50:48: ISAKMP (0:26): speaking to another IOS box!
05:50:48: ISAKMP:received payload type 17
05:50:48: ISAKMP:received payload type 17
05:50:48: ISAKMP (0:26): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_MAIN_MODE
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM4  
   New State = IKE_I_MM4 

05:50:48: ISAKMP (0:26): Send initial contact
05:50:48: ISAKMP (0:26): SA is doing pre-shared key authentication  
   using id type ID_IPV4_ADDR
05:50:48: ISAKMP (26): ID payload
next-payload : 8
type : 1
addr : 209.168.202.131
protocol : 17
port : 500
length : 8
05:50:48: ISAKMP (26): Total payload length: 12
05:50:48: ISAKMP (0:26): sending packet to 209.168.202.130 my_port 500  
   peer_port 500 (I) MM_KEY_EXCH
05:50:48: ISAKMP (0:26): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_COMPLETE
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM4  
   New State = IKE_I_MM5 

05:50:48: ISAKMP (0:26): received packet from 209.168.202.130 dport 500  
   sport 500 Global (I) MM_KEY_EXCH
05:50:48: ISAKMP (0:26): Input = IKE_MESG_FROM_PEER,  
   IKE_MM_EXCH
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM5  
   New State = IKE_I_MM6 

05:50:48: ISAKMP (0:26): processing ID payload. message ID = 0
05:50:48: ISAKMP (0:26): processing HASH payload. message ID = 0
05:50:48: ISAKMP (0:26): SA has been authenticated with 209.168.202.130
05:50:48: ISAKMP (0:26): peer matches *none* of the profiles
05:50:48: ISAKMP (0:26): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_MAIN_MODE
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM6  
   New State = IKE_I_MM6 

05:50:48: ISAKMP (0:26): Input = IKE_MESG_INTERNAL,  
   IKE_PROCESS_COMPLETE
05:50:48: ISAKMP (0:26): Old State = IKE_I_MM6  
   New State = IKE_P1_COMPLETE 

05:50:48: ISAKMP (0:26): beginning Quick Mode exchange,  
   M-ID of -1682446278
05:50:48: ISAKMP (0:26): sending packet to 209.168.202.130 my_port 500  
   peer_port 500 (I) QM_IDLE 
05:50:48: ISAKMP (0:26): Node -1682446278, Input = IKE_MESG_INTERNAL,  
   IKE_INIT_QM
05:50:48: ISAKMP (0:26): Old State = IKE_QM_READY  
   New State = IKE_QM_I_QM1
05:50:48: ISAKMP (0:26): Input = IKE_MESG_INTERNAL,  
   IKE_PHASE1_COMPLETE
05:50:48: ISAKMP (0:26): Old State = IKE_P1_COMPLETE  
   New State = IKE_P1_COMPLETE 

05:50:48: ISAKMP (0:26): received packet from 209.168.202.130 dport 500  
   sport 500 Global (I) QM_IDLE 
05:50:48: ISAKMP (0:26): processing HASH payload.  
   message ID = -1682446278
05:50:48: ISAKMP (0:26): processing SA payload.  
   message ID = -1682446278
05:50:48: ISAKMP (0:26): Checking IPSec proposal 1
05:50:48: ISAKMP: transform 1, ESP_3DES
05:50:48: ISAKMP: attributes in transform:
05:50:48: ISAKMP: encaps is 1
05:50:48: ISAKMP: SA life type in seconds
05:50:48: ISAKMP: SA life duration (basic) of 120
05:50:48: ISAKMP: SA life type in kilobytes
05:50:48: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0 
05:50:48: ISAKMP: authenticator is HMAC-MD5
05:50:48: ISAKMP (0:26): atts are acceptable.
05:50:48: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 209.168.202.131,  
   remote= 209.168.202.130, 
local_proxy= 209.168.202.131/255.255.255.255/47/0 (type=1), 
remote_proxy= 209.168.202.130/255.255.255.255/47/0 (type=1),
protocol= ESP, transform= esp-3des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x2
05:50:48: IPSEC(kei_proxy): head = Tunnel0-head-0,  
   map->ivrf = , kei->ivrf = 
05:50:48: IPSEC(kei_proxy): head = Tunnel0-head-0,  
   map->ivrf = , kei->ivrf = 
05:50:48: ISAKMP (0:26): processing NONCE payload.  
   message ID = -1682446278
05:50:48: ISAKMP (0:26): processing ID payload.  
   message ID = -1682446278
05:50:48: ISAKMP (0:26): processing ID payload.  
   message ID = -1682446278
05:50:48: ISAKMP (0:26): Creating IPSec SAs
05:50:48: inbound SA from 209.168.202.130 to  
   209.168.202.131 (f/i) 0/ 0
(proxy 209.168.202.130 to 209.168.202.131)
05:50:48: has spi 0x6E42707E and conn_id 5547 and flags 2
05:50:48: lifetime of 120 seconds
05:50:48: lifetime of 4608000 kilobytes
05:50:48: has client flags 0x0
05:50:48: outbound SA from 209.168.202.131 to 209.168.202.130  
   (f/i) 0/ 0 (proxy 209.168.202.131 to 209.168.202.130)
05:50:48: has spi -359889983 and conn_id 5548 and flags A
05:50:48: lifetime of 120 seconds
05:50:48: lifetime of 4608000 kilobytes
05:50:48: has client flags 0x0
05:50:48: IPSEC(key_engine): got a queue event...
05:50:48: IPSEC(initialize_sas): ,
(key eng. msg.) INBOUND local= 209.168.202.131,  
   remote= 209.168.202.130, 
local_proxy= 209.168.202.131/0.0.0.0/47/0 (type=1), 
remote_proxy= 209.168.202.130/0.0.0.0/47/0 (type=1),
protocol= ESP, transform= esp-3des esp-md5-hmac , 
lifedur= 120s and 4608000kb, 
spi= 0x6E42707E(1849847934), conn_id= 5547, keysize= 0, flags= 0x2
05:50:48: IPSEC(initialize_sas): ,
(key eng. msg.) OUTBOUND local= 209.168.202.131,  
   remote= 209.168.202.130, 
local_proxy= 209.168.202.131/0.0.0.0/47/0 (type=1), 
remote_proxy= 209.168.202.130/0.0.0.0/47/0 (type=1),
protocol= ESP, transform= esp-3des esp-md5-hmac , 
lifedur= 120s and 4608000kb, 
spi= 0xEA8C83C1(3935077313), conn_id= 5548, keysize= 0, flags= 0xA
05:50:48: IPSEC(kei_proxy): head = Tunnel0-head-0,  
   map->ivrf = , kei->ivrf = 
05:50:48: IPSEC(kei_proxy): head = Tunnel0-head-0,  
   map->ivrf = , kei->ivrf = 
05:50:48: IPSEC(add mtree): src 209.168.202.131, dest 209.168.202.130,  
   dest_port 0

05:50:48: IPSEC(create_sa): sa created,
(sa) sa_dest= 209.168.202.131, sa_prot= 50, 
sa_spi= 0x6E42707E(1849847934), 
sa_trans= esp-3des esp-md5-hmac , sa_conn_id= 5547
05:50:48: IPSEC(create_sa): sa created,
(sa) sa_dest= 209.168.202.130, sa_prot= 50, 
sa_spi= 0xEA8C83C1(3935077313), 
sa_trans= esp-3des esp-md5-hmac , sa_conn_id= 5548
05:50:48: ISAKMP (0:26): sending packet to 209.168.202.130 my_port 500  
   peer_port 500 (I) QM_IDLE 
05:50:48: ISAKMP (0:26): deleting node -1682446278 error FALSE reason ""
05:50:48: ISAKMP (0:26): Node -1682446278, Input = IKE_MESG_FROM_PEER,  
   IKE_QM_EXCH
05:50:48: ISAKMP (0:26): Old State = IKE_QM_I_QM1  
   New State = IKE_QM_PHASE2_COMPLETE
05:50:49: ISAKMP (0:21): purging node 334570133
sv9-3#

相关的思科支持社区讨论

思科支持社区是您提问、解答问题、分享建议以及与工作伙伴协作的论坛。


相关信息


Document ID: 29240