2015 年 8 月 28 日 - 机器翻译
其他版本: PDFpdf | 英语 (2015 年 4 月 22 日) | 反馈


目录

简介
先决条件
要求
使用的组件
规则
IPX FRP硬件错误
相关的思科支持社区讨论
相关信息

简介

当异常情况出现时,Cisco广域网交换卡和模块记录错误代码。交换机卡错误是由在底部的一个CD符号的交换机命令行界面(CLI)屏幕显示给用户。您能使用.dspcderrs命令显示错误列表。将根据访问级别显示错误。

先决条件

要求

本文档没有任何特定的要求。

使用的组件

本文档不限于特定的软件和硬件版本。

规则

有关文档规则的详细信息,请参阅 Cisco 技术提示规则

IPX FRP硬件错误

在此部分的此列表是IPX帧中继填充卡德(FRP)硬件错误的一参考被提交至strataCom级别。StrataCom级别错误只服务有意义。您也许不发现列出的所有错误。

=============================================================================

  ==== HARDWARE AND SOFTWARE error lists (hw_code.h)     BY MGC (09-30-92)

  ====

  ==== Present Revision: 2.0                                              

  ====

  ==== Revision History: FDE/FEE + FTC                   BY CvH (05-25-94)

  ====

  ====                   Added Self-Test Failures        BY CvH (06-22-94)

  ====

  ====                   Corrections                     BY CvH (08-18-94)

  ====

  ====                   Add non-ACP errors              BY CvH (08-18-94)

  ====

  =============================================================================

  

  *** GENERIC FATAL ERRORS **** 

  Hardware Error Message Format

   |Fcn Code (if due to a command, else 0)

   | |Error: 1 - download failure

   | | |     2 - power-up failure   

   | | |     3 - selftest failure   

   | | |     4 - memory test failure

   | | |     5 - internal boot failure   

   | | |     6 - internal ACP failure   

   | | |     7 - watchdog failure   

   | | |Slot/Type (Type if MSB set): 99 (19) if FRP, A3 (23) if FTC

   | | | |Processor Number

   | | | | |

  0B01029901 000000ii xxxxxxxx yyyyyyyy : Power-up Failure 

              i  = failure state

             05h - novram checksum failed           

             06h - fifo loopback failed

             07h - no state 0 msg from supv. (SRAM problem)

             10h - fifo test failed

             11h - no state 1 msg from supv.

          >= 12h - passed boot prom (missed handshake)

          x = failure address, y = data expected

  0B01049901 xxxxxxxx yyyyyyyy zzzzzzzz: Memory Test Failure 

          x = failure address, y = data expected, z = data received

  0B01059901 000000ii : Internal Boot Failure 

             i = failure mode

             0 - waiting for HF flag change from DSP

             1 - waiting for TXDE flag to go true from DSP

             2 - waiting for RXDF flag to go true from DSP

             3 - unable to initialize DSP

             4 - unable to internal load DSP

             5 - unable to program EEPROM

             6 - bad message from CBUS controller

             7 - 9th bit/msg format error from supv.

             8 - no NMICLR in response to NMI to supv.

             9 - timeout waiting for space in Admin fifo

  0B00079901 : 8751 Watchdog Timeout

  

  *** FATAL HARDWARE ERRORS **** (The byte count will be 17)

  

  0B00069901 FF 01 00 00 [sr:16][pc addr][vo:16] : acp_stop Error     (@pc addr)

  0B00069901 FF 01 00 01 [ pc addr ] [err addr ] : pSOS K_FATAL Error (@pc addr)

      error usually a pSOS code: 4B = max. num. cnfg. timers exceeded

  

  *** FATAL ADDRESS/BUS EXCEPTION ERRORS **** (The byte count will be 23)

  

  0B00069901 FF 01 00 00 [sr:16][pc addr][vo:16][ssw:16][fault addr] 

  

  *** NON-FATAL HARDWARE ERRORS **** (The byte count will be 13)

  

  0B00069901 01 00 00 C0 [lcn      ] : Expect psos message (test frame)

  0B00069901 01 00 ii C1 00 00 00 00 : DIAGS test aborted in tm on; i = port

  0B00069901 01 00 ii C3 [message  ] : Loopback frm not received; i = port

  0B00069901 01 00 ii C4 [hchannel ] : Loopback frm bad hch number; i = port

  0B00069901 01 00 ii C5 [length   ] : Loopback frm bad frame length; i = port

  0B00069901 01 00 ii C6 [address  ] : Loopback frm incorrect data; i = port

  0B00069901 01 00 ii C7 [address  ] : Loopback frm zero segment; i = port

  0B00069901 01 00 ii C8 [testnum  ] : Invalid test number (diags); i = port

  0B00069901 01 00 00 C9 [bc type  ] : Bad internal card type

  0B00069901 01 00 ii C9 00 00 00 00 : DIAGS test aborted in tm off; i = port

  0B00069901 01 01 00 80 [response ] : Bad SLOT ID response (startup)

  0B00069901 01 01 00 90 00 00 00 00 : Bad watch dog timer event rcvd (cmd_task)

  0B00069901 01 01 D0 00 [status   ] : FPTX HP failure status during dnld

  0B00069901 01 01 D0 01 [status   ] : FPTX watchdog HP failure status

  0B00069901 01 01 D0 02 [status   ] : FPTX activate HP error status

  0B00069901 01 01 D0 03 [status   ] : FPTX deactivate HP error status

  0B00069901 01 01 D0 04 [status   ] : FPTX write command HP error status

  0B00069901 01 01 D0 05 [status   ] : FPTX read command HP error status

  0B00069901 01 01 D0 06 [status   ] : FPTX self test HP error status

  0B00069901 01 01 D0 07 [status   ] : FPTX activate: HP status bad

  0B00069901 01 01 D0 08 [status   ] : FPTX purge: HP status bad

  0B00069901 01 01 D0 09 [status   ] : FPTX purge all: HP status bad

  0B00069901 01 01 D0 0A [status   ] : FPTX suspend: HP status bad

  0B00069901 01 01 D0 0B [status   ] : FPTX resume: HP status bad

  0B00069901 01 01 D1 00 [status   ] : FPRX HP failure status during dnld

  0B00069901 01 01 D1 01 [status   ] : FPRX watchdog HP failure status

  0B00069901 01 01 D1 02 [status   ] : FPRX activate HP error status

  0B00069901 01 01 D1 03 [status   ] : FPRX deactivate HP error status

  0B00069901 01 01 D1 04 [status   ] : FPRX write command HP error status

  0B00069901 01 01 D1 05 [status   ] : FPRX read command HP error status

  0B00069901 01 01 D1 06 [status   ] : FPRX self test HP error status

  0B00069901 01 01 D1 07 [status   ] : FPRX cnfig MC HP status

  0B00069901 01 01 D1 08 [status   ] : FPRX stats bad HP status

                         [index    ] : STATS invalid stats buffer index

  0B00069901 01 01 D1 09 [status   ] : FPRX LCA boot response bad HP status

  0B00069901 01 01 D1 0A [status   ] : FPRX suspend cnfig MC HP status

  0B00069901 01 01 D1 0B [status   ] : FPRX resume cnfig MC HP status

  0B00069901 01 01 D2 00 [status   ] : DMA HP failure status during dnld

  0B00069901 01 01 D2 01 [status   ] : DMA watchdog HP failure status

  0B00069901 01 01 D2 02 [status   ] : DMA activate HP error status

  0B00069901 01 01 D2 03 [status   ] : DMA deactivate HP error status

  0B00069901 01 01 D2 04 [status   ] : DMA write command HP error status

  0B00069901 01 01 D2 05 [status   ] : DMA read command HP error status

  0B00069901 01 01 D2 06 [status   ] : DMA self test HP error status

  0B00069901 01 01 D2 07 [hch/stat ] : DMA HP msg failed @ enable channel

  0B00069901 01 01 D2 08 [hch/stat ] : DMA HP msg failed @ disable channel

  0B00069901 01 01 D2 0A [status   ] : DMA HP msg failed @ inc hp counter

  0B00069901 01 01 D2 0B [status   ] : DMA HP msg failed @ reset hp counter

  0B00069901 01 01 D2 0C [status   ] : DMA HP msg failed @ resume receive

  0B00069901 01 01 D2 0D [status   ] : DMA HP msg failed @ halt receive

  0B00069901 01 01 D2 0E [ts/stat  ] : DMA HP msg failed @ idle code

  0B00069901 01 01 D2 17 [code     ] : DMA enable channel msg code incorrect

  0B00069901 01 01 D2 18 [code     ] : DMA disable channel msg code incorrect

  0B00069901 01 01 D2 28 [length   ] : DMA disable channel msg len. incorrect

  0B00069901 01 02 00 8A [buf index] : FIFO cmd read too long/not end bit set

  0B00069901 01 02 00 8C [msg index] : FIFO cmd too long to write out

  0B00069901 01 02 00 8D 00 00 00 00 : Exceeded FIFO test wait time

  0B00069901 01 02 00 8E 00 00 00 00 : VC Table corrupted (    256 lcns)

  0B00069901 01 02 00 8F 00 00 00 00 : Complex GW con received OAM packet

  0B00069901 01 02 00 91 [Tmr 1 Cnt] : CIO Timer 1 Errors

  0B00069901 01 02 00 92 [Tmr 2 Cnt] : CIO Timer 2 Errors

  0B00069901 01 02 00 93 [Tmr 3 Cnt] : CIO Timer 3 Errors

  0B00069901 01 02 00 94 [Prt A Cnt] : CIO Port A Errors 

  0B00069901 01 02 00 95 [Prt B Cnt] : CIO Port B Errors 

  0B00069901 01 02 ii B0 00 00 00 00 : PRT_CTRL DxE setup failure;   i = port

  0B00069901 01 02 ii B1 [baudindex] : PRT_CTRL invalid baud rate;   i = port

  0B00069901 01 02 ii B2 [clkselect] : PRT_CTRL invalid clk select;  i = port

  0B00069901 01 02 ii B3 [timer cnt] : PRT_CTRL invalid pit count;   i = port

  0B00069901 01 02 ii B4 00 00 00 00 : BRSAMPLE invalid cntr value;  i = port

  0B00069901 01 02 ii B5 00 00 00 00 : BRSAMPLE invalid timer value; i = port

  0B00069901 01 02 ii B6 00 00 00 00 : BRSAMPLE zero elapsed time;   i = port

  0B00069901 01 02 ii B8 [eia lead ] : EIA_MON lead failure; i = port

  0B00069901 01 02 00 F2 [checksum ] : Bad novram checksum

  0B00069901 01 02 00 CA 00 00 00 ii : CAM_CTRL update_lcn_cam, inv. port = i

  0B00069901 01 02 01 CA 00 00 00 ii : CAM_CTRL clear_lcn_cam,  inv. port = i

  0B00069901 01 02 02 CA 00 00 00 ii : CAM_CTRL cam_lcn_lookup, inv. port = i

  

  0B00069901 D0 00 03 01 [data     ] : FPTX watchdog failure data

  0B00069901 D0 01 01 00 [length   ] : FPTX bad rsp length after dnld (dsp_ctrl)

  0B00069901 D0 01 01 01 [length   ] : FPTX watchdog response incorrect length

  0B00069901 D0 01 01 05 [length   ] : FPTX read command incorrect length

  0B00069901 D0 01 01 06 [length   ] : FPTX self test incorrect length  

  0B00069901 D0 01 01 09 [length   ] : FPTX purge all: incorrect length rtned

  0B00069901 D0 01 01 DB 00 00 00 00 : FPTX bootstrap failed

  0B00069901 D0 01 02 00 [code     ] : FPTX bad code rsp after dnld (dsp_ctrl)

  0B00069901 D0 01 02 01 [code     ] : FPTX watchdog incorrect fcn. code rtned

  0B00069901 D0 01 02 05 [code     ] : FPTX read command incorrect msg code

  0B00069901 D0 01 02 06 [code     ] : FPTX self test incorrect msg code

  0B00069901 D0 01 02 09 [code     ] : FPTX purge all: incorrect code returned

  0B00069901 D0 01 02 DB 00 00 00 00 : FPTX boot failed

  0B00069901 D0 01 03 00 [data     ] : FPTX bad data rsp after dnld (dsp_ctrl)

  0B00069901 D0 01 03 01 [data     ] : FPTX watchdog failure data

  0B00069901 D0 01 03 06 [status   ] : FPTX STSTS self-test error

  

  0B00069901 D1 00 03 01 [data     ] : FPRX watchdog failure data

  0B00069901 D1 01 01 01 [length   ] : FPRX watchdog response incorrect length

  0B00069901 D1 01 01 00 [length   ] : FPRX bad rsp length after dnld (dsp_ctrl)

  0B00069901 D1 01 01 05 [length   ] : FPRX read command incorrect length

  0B00069901 D1 01 01 06 [length   ] : FPRX self test incorrect length  

  0B00069901 D1 01 01 08 [length   ] : FPRX stats response bad length

  0B00069901 D1 01 01 09 [length   ] : FPRX LCA boot response bad length

  0B00069901 D1 01 01 DB 00 00 00 00 : FPRX bootstrap failed

  0B00069901 D1 01 02 00 [code     ] : FPRX bad code rsp after dnld (dsp_ctrl)

  0B00069901 D1 01 02 01 [code     ] : FPRX watchdog incorrect fcn code rtned

  0B00069901 D1 01 02 05 [code     ] : FPRX read command incorrect msg code

  0B00069901 D1 01 02 06 [code     ] : FPRX self test incorrect msg code

  0B00069901 D1 01 02 08 [code     ] : FPRX stats response bad code

  0B00069901 D1 01 02 09 [code     ] : FPRX LCA boot response bad code

  0B00069901 D1 01 02 DB 00 00 00 00 : FPRX boot failed

  0B00069901 D1 01 03 00 [data     ] : FPRX bad data rsp after dnld (dsp_ctrl)

  0B00069901 D1 01 03 01 [data     ] : FPRX watchdog failure data

  0B00069901 D1 01 03 06 [status   ] : FPRX STSTS self-test error

  0B00069901 D1 01 03 09 [data     ] : FPRX LCA boot error response data <> 0

  

  0B00069901 D2 00 03 01 [data     ] : DMA watchdog failure data

  0B00069901 D2 01 01 00 [length   ] : DMA bad rsp length after dnld (dsp_ctrl)

  0B00069901 D2 01 01 01 [length   ] : DMA watchdog response incorrect length

  0B00069901 D2 01 01 05 [length   ] : DMA read command incorrect length

  0B00069901 D2 01 01 06 [length   ] : DMA self test incorrect length  

  0B00069901 D2 01 01 09 [msg len  ] : DMA incorrect msg length  

  0B00069901 D2 01 01 DB 00 00 00 00 : DMA bootstrap failed

  0B00069901 D2 01 02 00 [code     ] : DMA bad code rsp after dnld (dsp_ctrl)

  0B00069901 D2 01 02 01 [code     ] : DMA watchdog incorrect fcn code rtned

  0B00069901 D2 01 02 05 [code     ] : DMA read command incorrect msg code

  0B00069901 D2 01 02 06 [code     ] : DMA self test incorrect msg code

  0B00069901 D2 01 02 09 [msg code ] : DMA incorrect msg code

  0B00069901 D2 01 02 DB 00 00 00 00 : DMA boot failed

  0B00069901 D2 01 03 00 [data     ] : DMA bad data rsp after dnld (dsp_ctrl)

  0B00069901 D2 01 03 01 [data     ] : DMA watchdog failure data

  0B00069901 D2 01 03 06 [status   ] : DMA STSTS self-test error

  0B00069901 D2 01 03 09 [msg data ] : DMA incorrect msg

  

  0B00069901 DB 02 01 00 [ISR ptr  ] : DSP not ready with TRDY

  0B00069901 DB 02 02 00 [ISR ptr  ] : DSP not ready with TXDE for bootstrap

  0B00069901 DB 02 03 00 [ISR ptr  ] : DSP not ready with TRDY for bootstrap

  0B00069901 DB 02 11 00 [ISR ptr  ] : DSP not ready with TXDE for boot

  0B00069901 DB 02 12 00 [ISR ptr  ] : DSP not ready for boot dnld

  0B00069901 DB 02 13 00 [ISR ptr  ] : DSP not ready with TRDY for boot

  0B00069901 DB 02 14 00 [ISR ptr  ] : DSP not ready with TXDE for boot

  0B00069901 DB 02 15 00 [ISR ptr  ] : DSP not ready with TRDY for boot

  

  0B00069901 DD 02 02 00 [ISR ptr  ] : DSP has not completed previous command

  0B00069901 DD 02 03 00 [CVR ptr  ] : DSP did not respond to sent command          

  0B00069901 DD 02 04 00 [ISR ptr  ] : DSP did not receive HP bytes

  0B00069901 DD 02 05 ii [ISR ptr  ] : DSP not ready to receive

  0B00069901 DD 02 06 00 [ISR ptr  ] : DSP did not ack command reception

  0B00069901 DD 02 07 00 [CVR ptr  ] : DSP not ready for "execute host" cmd

  0B00069901 DD 02 08 00 [ISR ptr  ] : DSP did not ack command completion

  0B00069901 DD 02 09 00 [ISR ptr  ] : DSP did not return HP command response

  0B00069901 DD 02 0A 00 [CVR ptr  ] : DSP not ready for slave read response

  0B00069901 DD 02 0B ii [ISR ptr  ] : DSP failed to return RXDF

  0B00069901 DD 02 0C 00 [CVR ptr  ] : DSP not ready for close output

  

  0B00069901 F0 01 00 03 [llcb_ptr ] : FREE_FRM: Frame Buffer Overflow (> Max FB/Frm)

  

  0B00069901 F1 01 00 03 [frm_ptr  ] : FTX_RECY: Frame Buffer Overflow (> Max FB/Frm)

  0B00069901 F1 01 00 05 00 00 00 00 : FTX_RECY: Spyder overrun

  0B00069901 F1 01 00 06 00 00 00 00 : FTX_RECY: Spyder underrun

  0B00069901 F1 01 00 07 [hpr_q_ptr] : FTX_PURG: Bad Hi-priority Q pointer

  0B00069901 F1 01 00 08 [lpr_q_ptr] : FTX_PURG: Bad Lo-priority Q pointer

  0B00069901 F1 01 00 09 [fim_q_ptr] : FIM_PURG: Bad Fim Q pointer

  0B00069901 F1 01 00 0D [dma error] : FTX_RECY: Undefined TX DMA Error

  

  0B00069901 F2 01 00 01 [fcb_tail ] : FRX_RECY: FCB Q overflow [Port only]

  0B00069901 F2 01 00 03 [frm_ptr  ] : FRX_RECY: Recycled too many frame bufs

  0B00069901 F2 01 00 04 [prev_fptr] : FRX_RXFR: SOF rcvd B4 last frame's EOF

                         [curr_fptr] : FRX_RXFR: (always comes in pairs)

  0B00069901 F2 01 00 05 [error    ] : FRX_RXFR: Unexpected DMA error code

  0B00069901 F2 01 00 06 00 00 00 00 : FRX_RXFR: SPYDER UNDERRUN

  0B00069901 F2 01 00 0A [pointer  ] : FRX_RXFR: DMA interrupt Q Overrun

  0B00069901 F2 01 00 0B [error    ] : FRX_RXFR: Undefined RX DMA error

  0B00069901 F2 01 00 0C [hyperch  ] : FRX_RECY: FB in use underrun (count)

  0B00069901 F2 01 00 0E [frm_ptr  ] : FRX_IDLE: Zero FB Reported (FRX_DLOK/DLC0/PTLB)

  0B00069901 F2 01 00 0F [hyperch  ] : FRX_RXFR: Invalid DMA hyperchannel

  0B00069901 F2 01 00 10 [pt_rx_ptr] : FRX_RXFR: Invalid DMA offset

  0B00069901 F2 01 00 11 [frm_ptr  ] : FRX_RXFR: Firmware Frame in Progress Error

  0B00069901 F2 01 00 12 [frm_ptr  ] : FRX_RXFR: Missing EOF Status

  0B00069901 F2 01 00 13 [frm_ptr  ] : FRX_RXFR: Sequence Error Status

  

  *** SOFTWARE ERRORS **** (The byte count will be 3)

  Guidelines for Error Codes:  0 - unknown function code

                               1 - illegal length

                               2 - illegal parameter

                               3 - unused

                               4 - illegal for card state

                               5 - illegal for channel state

                               6 - configuration error

                               7 - illegal for backcard state

  

  Error Code  Module     Error Reason

  ----------  --------   ---------------------------------------

  02 xx 00  : COMMAND  : Invalid command         *** SPECIAL ***

  02 xx 01  : COMMAND  : Invalid message length  *** SPECIAL ***

  02 03 03  : CMD_STST : Bad self test number ( != 0 or 1)

  02 03 04  : CMD_STST : FRIC not active

  02 18 02  : CMD_MEM  : Bad parameter (write_memory_cmd)

  02 19 02  : CMD_MEM  : Bad parameter ( read_memory_cmd)

  02 1A 04  : CMD_MEM  : Command not supported (memory_test_cmd)

  02 1B 02  : CMD_MEM  : Bad parameter (write_NOVRAM_cmd)

  02 1C 02  : CMD_MEM  : Bad parameter ( read_NOVRAM_cmd)

  02 1D 02  : CMD_LED  : Bad LED bitmap

  02 1E 02  : CMD_DBUG : Command not supported (scope_loop_cmd)

  02 1F 02  : CMD_DBUG : Invalid processor type (ascii_event_cmd)

  02 20 04  : CMD_DNLD : Command not supported (transfer_begin_cmd) [PORT]

  02 21 04  : CMD_DNLD : Command not supported (transfer_cmd)       [PORT]

  02 22 04  : CMD_DNLD : Command not supported (transfer_end_cmd)   [PORT]

  02 A0 02  : CMD_CFBC : Back card type mismatch

  02 A0 03  : CMD_CFBC : Bad BC state parameter (BC_RESET)

  02 A0 04  : CMD_CFBC : Bad BC state parameter (UNKNOWN)

  02 A1 02  : CMD_BCST : Port not configured yet

  02 A2 02  : CMD_ALM  : Port not configured yet

  02 A2 03  : CMD_ALM  : Back card type mismatch

  02 AB 04  : CMD_DCC  : Bad time slot number ( >= MAX_E1_TIMESLOTS)

  02 B0 02  : CMD_HCH  : Bad hyperchannel number ( >= MAX_HCHANNELS)

            : CMD_PORT : Bad port ( >= Bd_Table.back_card_ports)

  02 B0 04  : CMD_HCH  : FRIC not active

  02 B0 05  : CMD_HCH  : Unallowd port reconfig (eg Bundled <=   Unbundled) 

  02 B0 06  : CMD_HCH  : Bad timeslot configuration

  02 B0 07  : CMD_HCH  : Timeslot number out of range

  02 B0 08  : CMD_HCH  : Timeslot already activated/deactivated

  02 B0 xx  : CMD_HCH  : Bad back card type (xx = rcvd back card type)

  02 B1 02  : CMD_PORT : Bad port ( >= Bd_Table.back_card_ports)

  02 B2 02  : CMD_HCST : Bad hyperchannel number ( >= MAX_HCHANNELS)

            : CMD_PTST : Bad port ( >= Bd_Table.back_card_ports)

  02 B3 02  : EIA_EVT  : Bad port ( >= Bd_Table.back_card_ports) [PORT]

                         (get_port_eia_status_cmd)

  02 B4 02  : CARD_EVT : local bus param non-zero

  02 B7 04  : CMD_ICA  : FRIC not active

  02 B8 02  : CMD_HCCG : Bad hyperchannel number ( >= MAX_HCHANNELS)

            : CMD_PTCG : Bad port ( >= Bd_Table.back_card_ports)

  02 B8 04  : CMD_HCCG : FRIC not active

  02 B9 02  : CMD_HCCG : Bad hyperchannel number ( >= MAX_HCHANNELS)

            : CMD_PTCG : Bad port ( >= Bd_Table.back_card_ports)

  02 BF 02  : CMD_DIAG : Bad port ( >= Bd_Table.back_card_ports) [PORT]

                         Bad test number ( != 1,2,3) [PORT]

                         Bad test number to terminate

  02 BF 03  : CMD_DIAG : Bad hyperchannel number ( >= MAX_HCHANNELS)

  02 BF 04  : CMD_DIAG : Hyperchannel/FRIC not active

  02 BF 05  : CMD_DIAG : Bad test number ( != 1, 2, or FF) [LINE]

            : CMD_DIAG : Port not active [PORT]

  02 BF 06  : CMD_DIAG : Bad test number to terminate

  02 BF 07  : CMD_DIAG : FRIC not active

  02 C0 02  : CMD_VC   : Bad hyperchannel number, DLCI, LCN

            : CMD_VC   : Bad DLCI, port ( >= Bd_Table.back_card_ports)

  02 C0 03  : CMD_VC   : Hch/port number doesn't match database for active LC

  02 C0 04  : CMD_VC   : FRIC not active

  02 C0 05  : CMD_VC   : VC already active (used by multicast) [REMOVE]

  02 C0 07  : CMD_VC   : VC already active

  02 C0 08  : CMD_VC   : FastPAD not active

  02 C1 02  : CMD_VC   : Bad LCN [REMOVE]

  02 C1 05  : CMD_VC   : VC already active (used by multicast) [REMOVE]

  02 C2 02  : CMD_VCST : Bad LCN [REMOVE]

  02 C5 02  : CMD_MC   : Command not supported

  02 C6 02  : CMD_MC   : Command not supported

  02 C7 02  : CMD_RTD  : Bad LCN [REMOVE]

  02 C7 04  : CMD_RTD  : FRIC not active

  02 C8 02  : CMD_VCCG : Bad LCN [REMOVE], LCN not active 

  02 C8 03  : CMD_VCCG : LCN not active

  02 C8 04  : CMD_VCCG : FRIC not active

  02 C9 02  : CMD_VCCG : Bad LCN [REMOVE]

  02 CC 02  : CMD_FPID : FRIC not active [PORT-FTC]

  02 CC 03  : CMD_FPID : Bad port ( >= MAX_PORT) [PORT-FTC]

  02 CC 04  : CMD_FPID : No match & no space found in Fp_Table [PORT-FTC]

  02 CC 05  : CMD_FPID : Bundling on Fp inconsistent with Port [PORT-FTC]

  

  

  *** SELF-TEST RESPONSES **** (from STSTS)

  Code                            Meaning

  ----------                      ---------------------------------------

  03 00                         : Done  (Success)

  03 80                         : Abort

  03 01 01 02 00 F0 00 00 00 00 : Fail - invalid FPTX self-test

  03 01 01 02 00 F0 00 00 00 01 : Fail - invalid FPRX self-test

  03 01 01 02 00 F0 00 00 00 02 : Fail - invalid DMA  self-test

  03 01 01 02 00 F2 xx xx yy yy : Fail - self_test_eeprom: x = calc.

  checksum,

                                         y = stored checksum @ 83FFFC

  03 01 01 02 xx F3 yy yy yy yy : Fail - self_test_routing_table: x =

  test,

                                         y = routing table address

  03 01 01 02 xx F4 yy yy yy yy : Fail - self_test_gram: x = test,

                                         y = GRAM address

  03 01 01 02 00 F5 [data & 30] : Fail - self_test_power_monitor

  03 01 D0 01 01 06 [  status ] : Fail - self_test_fptx

  03 01 D1 01 01 06 [  status ] : Fail - self_test_fprx

  03 01 D2 01 01 06 [  status ] : Fail - self_test_dma

  03 01 D2 CA CA ii xx xx yy yy : Fail - self_test_cam [LINE]

                                  i = data pattern, x = lcn, y = CAM lcn

相关的思科支持社区讨论

思科支持社区是您提问、解答问题、分享建议以及与工作伙伴协作的论坛。


相关信息


Document ID: 10815