IP : Protocole SNMP (Simple Network Management Protocol)

Objets MIB équivalents pour les commandes show VoIP

18 octobre 2016 - Traduction automatique
Autres versions: PDFpdf | Anglais (22 août 2015) | Commentaires


Contenu


Introduction

Ce document couvre les objets équivalents MIB qui fournissent les informations contenues dans diverses commandes de vérification de la voix sur ip (VoIP). Les applications et/ou les scripts NMS peuvent potentiellement utiliser ces informations.

Conditions préalables

Conditions requises

Aucune spécification déterminée n'est requise pour ce document.

Composants utilisés

Ce document n'est pas limité aux versions de logiciel spécifiques. Cependant, on lui écrit spécifiquement pour un routeur de gamme Cisco 3600 avec une carte NM-2V.

Les informations contenues dans ce document ont été créées à partir des périphériques d'un environnement de laboratoire spécifique. Tous les périphériques utilisés dans ce document ont démarré avec une configuration effacée (par défaut). Si votre réseau est opérationnel, assurez-vous que vous comprenez l'effet potentiel de toute commande.

Conventions

Pour plus d'informations sur les conventions de documents, reportez-vous à Conventions relatives aux conseils techniques Cisco.

Configuration

Cette sortie affiche une partie appropriée de la configuration que ce document l'utilise :

VoipRouter#show running-configuration
Building configuration...

Current configuration : 5412 bytes
!
version 12.3
...
!
snmp-server community public RO
!
...
!
voice-port 2/0/0
!
...
!
dial-peer voice 2000 pots
 destination-pattern 2000
 port 2/0/0
!
dial-peer voice 1000 voip
 destination-pattern 1000
 session target ipv4:172.16.99.22
!
...
end

Commandes VoIP

Ces sections affichent les objets MIB qui correspondent à la sortie de ces commandes de vérification VoIP :

Les informations que ces la vérification VoIP commande contiennent peuvent être extraites d'IF-MIB, de CISCO-VOICE-IF-MIB, de CISCO-VOICE-ANALOG-IF-MIB, de CISCO-VOICE-DIAL-CONTROL-MIB, de DIAL-CONTROL-MIB, et de CISCO-DSP-MGMT-MIB.

Remarque: Dans ces exemples, le tronçon de téléphonie est indexé par 1102799 et H.323 le tronçon est indexé par 1102966.

résumé de show voice port

Remarque: Le texte en gras dans la commande récapitulative de show voice port est tracé les grandes lignes dans la section équivalente d'objets MIB.

VoipRouter#show voice port summary
                                      IN           OUT
PORT      CH   SIG-TYPE   ADMIN OPER  STATUS       STATUS   EC
========= == ============ ===== ====  ========     ======== ==
2/0/0(A1) --  fxs-ls(A2)  up(A3)up(A4) off-hook(A5) idle     y(A6) 
2/0/1     --  fxs-ls      up    dorm   on-hook      idle     y 

Objets équivalents MIB

A1  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

A2  —  CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.37 = INTEGER: fxsLoopStart(1)

A3  —  IF-MIB::ifAdminStatus.37 = INTEGER: up(1)

A4  —  IF-MIB::ifOperStatus.37 = INTEGER: up(1)

A5  —  CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.37 = INTEGER: offHook(2)

A6  —  CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.37 = INTEGER: true(1)

Remarque: Aucun objet MIB ne met à jour la valeur contenue dans la partie ch de la commande récapitulative de show voice port quand la carte NM-2V est utilisée.

résumé de show voice call

Remarque: Le texte en gras dans la commande récapitulative de show voice call est tracé les grandes lignes dans la section équivalente d'objets MIB.

VoipRouter#show voice call summary
PORT         CODEC      VAD   VTSP STATE            VPM STATE
============ ========   ===   ==================== ======================
2/0/0(B1)    g729r8(B2) y(B3) S_CONNECT             FXSLS_CONNECT            
2/0/1         -         -       -                   FXSLS_ONHOOK             

Objets équivalents MIB

B1  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

B2  —  CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCoderTypeRate.
       1102966.1 = INTEGER: ietfg729r8000(25)

B3  —  CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveVADEnable.
       1102966.1 = INTEGER: true(1)

Remarque: Aucun objet MIB ne met à jour le fournisseur de service de téléphonie voix (VTSP) et des états VPM individuellement. CallActiveCallState d'utilisation de DIAL-CONTROL-MIB à la place.

résumé de show dial-peer voice

Remarque: Le texte en gras dans la commande récapitulative de show dial-peer voice est tracé les grandes lignes dans la section équivalente d'objets MIB.

VoipRouter#show dial-peer voice summary
dial-peer hunt 0
             AD                                        PRE  PASS
TAG      TYPE     MIN     OPER    PREFIX DEST-PATTERN  FER  THRU SESS-TARGET   PORT
2000(C1) pots(C2)  up(C3)  up(C4) 9(C5)   2000(C6)     0(C7)                2/0/0(C8)
1000     voip      up      up             1000         0    syst ipv4:172.16.99.22(C9)   

Objets équivalents MIB

C1  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.2000 = INTEGER: 90

    —  DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.2000.90 = INTEGER: 37
C2  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.2000 = INTEGER: voice(1)

C3  —  IF-MIB::ifAdminStatus.37 = INTEGER: up(1)

C4  —  IF-MIB::ifOperStatus.37 = INTEGER: up(1)

C5  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDialDigitsPrefix.90 = STRING: 9

C6  —  DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.2000.90 = STRING: 2000

C7  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.90 = INTEGER: 0

C8  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

C9  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionTarget.91 = 
       STRING: ipv4:172.16.99.22

Remarque: Aucun objet MIB ne met à jour la valeur contenue dans le modem TRAVERSENT la partie de méthode de la commande de résumé de cadran-pair d'exposition.

brief de show call active voice

Remarque: Le texte en gras dans la commande brief de show call active voice est tracé les grandes lignes dans la section équivalente d'objets MIB.

VoIPRouter#show call active voice brief 
   
<ID>:<start>hs.<index> +<connect> pid:<peer_id> <dir> <addr> <state>  
  dur hh:mm:ss tx:<packets>/<bytes> rx:<packets>/<bytes>  
 IP <ip>:<udp> rtt:<time>ms pl:<play>/<gap>ms lost:<lost>/<early>/<late>  
  delay:<last>/<min>/<max>ms <codec>  
  MODEMPASS <method> buf:<fills>/<drains> loss <overall%>  
<multipkt>/<corrected>  
   last <buf event time>s dur:<Min>/<Max>s  
 FR <protocol> [int dlci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>  
  sig:<on/off> <codec> (payload size)  
ATM <protocol> [int vpi/vci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>  
  sig:<on/off> <codec> (payload size)  
 Tele <int>:tx:<tot>/<v>/<fax>ms <codec> noise:<l> acom:<l> i/o:<l>/<l>  
dBm  
MODEMRELAY info:<rcvd>/<sent>/<resent> xid:<rcvd>/<sent>  
total:<rcvd>/<sent>/<drops>  
 Proxy <ip>:<audio udp>,<video udp>,<tcp0>,<tcp1>,<tcp2>,<tcp3> endpt: 
<type>/<manf>  
 bw:<req>/<act> codec:<audio>/<video>  
  tx:<audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120  
pkts>/<t120 bytes>  
 rx:<audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120  
pkts>/<t120 bytes>  
Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 1
MGCP call-legs: 0
Total call-legs: 2
11D9 : 1102799(D1)hs.1 +1324 pid:2000(D2) Answer(D3) 2000(D4) active(D5)
 dur 1d19h(D6) tx:7875641(D7)/157512782(D8) rx:7875955(D9)/157519081(D10)
 Tele 2/0/0(D11):1: tx:157515460(D12)/157514630(D13)/0ms g729r8(D14)
 noise:-56(D15) acom:5(D16)  i/0:-40(D17)/-46(D18) dBm

11D9 : 1102966hs.1 +1157 pid:1000 Originate 1000 active
 dur 1d19h tx:7875388/157507741 rx:7875641/157512782
 IP 172.16.99.22(D19):19066(D20) rtt:6ms(D21) pl:157496940(D22)/4770ms(D23)
 lost:52(D24)/1(D25)/325(D26) delay:67(D27)/55(D28)/132ms(D29) g729r8

Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 1
MGCP call-legs: 0
Total call-legs: 2

Objets équivalents MIB

D1  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveConnectionId.1102799.1
       = Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC

D2  —  DIAL-CONTROL-MIB::callActivePeerId.1102799.1 = INTEGER: 2000

D3  —  DIAL-CONTROL-MIB::callActiveCallOrigin.1102799.1 = INTEGER: answer(2)

D4  —  DIAL-CONTROL-MIB::callActivePeerAddress.1102799.1 = STRING: 2000

D5  —  DIAL-CONTROL-MIB::callActiveCallState.1102799.1 = INTEGER: active(4)

D6  —  DIAL-CONTROL-MIB::callActiveConnectTime.1102799.1 = Timeticks: 
       (1104123) 3:04:01.23
    —  DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16590203) 1 days, 
       22:05:02.03

D7  —  DIAL-CONTROL-MIB::callActiveTransmitPackets.1102799.1 = Gauge32: 7875641

D8  —  DIAL-CONTROL-MIB::callActiveTransmitBytes.1102799.1 = Gauge32: 157512782

D9  —  DIAL-CONTROL-MIB::callActiveReceivePackets.1102799.1 = Gauge32: 7875955

D10 —  DIAL-CONTROL-MIB::callActiveReceiveBytes.1102799.1 = Gauge32: 157519081

D11 —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

D12 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveTxDuration.
       1102799.1 = Gauge32: 157515460 milliseconds

D13 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveVoiceTxDuration.
       1102799.1 = Gauge32: 157514630 milliseconds

D14 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveCoderTypeRate.
       1102799.1 = INTEGER: ietfg729r8000(25)

D15 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveNoiseLevel.
       1102799.1 = INTEGER: -56 dBm

D16 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveACOMLevel.
       1102799.1 =  INTEGER: 5 dB

D17 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveInSignalLevel.
       1102799.1 = INTEGER: -40 dBm

D18 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveOutSignalLevel.
       1102799.1 = INTEGER: -46 dBm

D19 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteIPAddress.
       1102966.1 = IpAddress: 172.16.99.22

D20 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteUDPPort.
       1102966.1 = INTEGER: 19066

D21 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRoundTripDelay.
       1102966.1 = Gauge32: 6 milliseconds

D22 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveOnTimeRvPlayout.
       1102966.1 = Gauge32: 157496940 milliseconds

D23 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithSilence.
       1102966.1 = Gauge32: 1090 milliseconds
    —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithPrediction.
       1102966.1 = Gauge32: 3680 milliseconds
    —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithInterpolation.
       1102966.1 = Gauge32: 0 milliseconds

D24 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLostPackets.
       1102966.1 = Gauge32: 52 packets

D25 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEarlyPackets.
       1102966.1 = Gauge32: 1 packets

D26 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLatePackets.
       1102966.1 = Gauge32: 325 packets

D27 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveReceiveDelay.
       1102966.1 = Gauge32: 67

D28 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLoWaterPlayoutDelay.
       1102966.1 = Gauge32: 55 milliseconds

D29 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveHiWaterPlayoutDelay.
       1102966.1 = Gauge32: 132 milliseconds

Remarque: La valeur de GapFill de la commande brief de show call active voice est obtenue quand vous ajoutez le cvVoIPCallActiveGapFillWithSilence, le cvVoIPCallActiveGapFillWithPrediction, et le cvVoIPCallActiveGapFillWithInterpolation d'objets SNMP.

show voice dsp

VoIPRouter#show voice dsp
 
DSP  DSP             DSPWARE CURR  BOOT                         PAK     TX/RX
TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
C549 009 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     05     0         0/36
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     06     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     07     0          0/0
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     08     0          0/0
C549 010 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     09     0          0/0
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     10     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     11     0          0/0
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     12     0          0/0
C549 011 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     13     0          0/0
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     14     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     15     0          0/0
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     16     0          0/0
C549 012 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     17     0          0/0
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     18     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     19     0          0/0
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     20     0          0/0
C549 013 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     21     0          0/0
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     22     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     23     0         0/12
         04 g729r8    4.1.31 busy  idle         0 1/0:0     24     0    176/56702
C549 014 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     01     0         0/27
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     02     0         0/12
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     03     0         0/12
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     04     0         0/12

Voici quelques objets utiles MIB qui fournissent des informations au sujet de l'appel actif dans l'exemple de sortie de la commande de show voice dsp :

CISCO-DSP-MGMT-MIB::cdspCardIndex.7 = INTEGER: 2
OLD-CISCO-CHASSIS-MIB::cardType.2 = INTEGER: hdv(516)
OLD-CISCO-CHASSIS-MIB::cardDescr.2 = STRING: "High Density Voice"
ENTITY-MIB::entPhysicalDescr.7 = STRING: High Density Voice
ENTITY-MIB::entPhysicalDescr.22 = STRING: DSP (C549)
CISCO-DSP-MGMT-MIB::cdspCardState.7 = INTEGER: normal(1)
CISCO-DSP-MGMT-MIB::cdspCardMaxChanPerDSP.7 = Gauge32: 4 channels
CISCO-DSP-MGMT-MIB::cdspTotalChannels.22 = Gauge32: 4 channels
CISCO-DSP-MGMT-MIB::cdspActiveChannels.21 = Gauge32: 1 channels

Remarque: Le MIB qui contient le dsp de Voix de l'information en démonstration est CISCO-DSP-MGMT-MIB. Cependant, en raison de l'ID de bogue Cisco CSCeb62542 pour la carte NM-2V, des DSP sur NM-2V ne sont pas affichés dans ENTITY-MIB. Puisque cdspCardStatusTable dépend de l'entPhysicalIndex d'ENTITY-MIB, cdspCardStatusTable n'est pas rempli pour la carte NM-2V.

Annexe

Cette sortie affiche le snmpwalk complet du ciscoVoiceAnalogIfMIB de CISCO-VOICE-ANALOG-IF-MIB au moment des commandes de vérification VoIP affichées dans ce document :

snmpwalk -c public 172.16.100.20 CISCO-VOICE-ANALOG-IF-MIB:ciscoVoiceAnalogIfMIB
CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgImpedance.37 = INTEGER: ohms600Real(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgImpedance.38 = INTEGER: ohms600Real(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgIntegratedDSP.37 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgIntegratedDSP.38 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusInfoType.37 = INTEGER: voice(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusInfoType.38 = INTEGER: none(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfMaintenanceMode.37 = INTEGER: none(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfMaintenanceMode.38 = INTEGER: none(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusSignalErrors.37 = Counter32: 0
CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusSignalErrors.38 = Counter32: 0
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.37 = INTEGER: fxsLoopStart(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.38 = INTEGER: fxsLoopStart(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingFrequency.37 = INTEGER: ringFrequency25(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingFrequency.38 = INTEGER: ringFrequency25(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.37 = INTEGER: offHook(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.38 = INTEGER: onHook(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingActive.37 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingActive.38 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingGround.37 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingGround.38 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTipGround.37 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTipGround.38 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingDigitDuration.37 = 
INTEGER: 100 milliseconds
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingDigitDuration.38 = 
INTEGER: 100 milliseconds
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingInterDigitDuration.37 = 
INTEGER: 100 milliseconds
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingInterDigitDuration.38 = 
INTEGER: 100 milliseconds

Cette sortie affiche le snmpwalk complet du ciscoVoiceInterfaceMIB de CISCO-VOICE-IF-MIB au moment des commandes de vérification VoIP affichées dans ce document :

snmpwalk -c public 172.16.100.20 CISCO-VOICE-IF-MIB:ciscoVoiceInterfaceMIB
CISCO-VOICE-IF-MIB::cvIfCfgNoiseRegEnable.37 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgNoiseRegEnable.38 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgNonLinearProcEnable.37 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgNonLinearProcEnable.38 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgMusicOnHoldThreshold.37 = INTEGER: -38 dBm
CISCO-VOICE-IF-MIB::cvIfCfgMusicOnHoldThreshold.38 = INTEGER: -38 dBm
CISCO-VOICE-IF-MIB::cvIfCfgInGain.37 = INTEGER: 0 dB
CISCO-VOICE-IF-MIB::cvIfCfgInGain.38 = INTEGER: 0 dB
CISCO-VOICE-IF-MIB::cvIfCfgOutAttn.37 = INTEGER: 3 dB
CISCO-VOICE-IF-MIB::cvIfCfgOutAttn.38 = INTEGER: 3 dB
CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.37 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.38 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelCoverage.37 = INTEGER: 4
CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelCoverage.38 = INTEGER: 4
CISCO-VOICE-IF-MIB::cvIfCfgConnectionMode.37 = INTEGER: normal(1)
CISCO-VOICE-IF-MIB::cvIfCfgConnectionMode.38 = INTEGER: normal(1)
CISCO-VOICE-IF-MIB::cvIfCfgConnectionNumber.37 = STRING: 
CISCO-VOICE-IF-MIB::cvIfCfgConnectionNumber.38 = STRING: 
CISCO-VOICE-IF-MIB::cvIfCfgInitialDigitTimeOut.37 = INTEGER: 10 seconds
CISCO-VOICE-IF-MIB::cvIfCfgInitialDigitTimeOut.38 = INTEGER: 10 seconds
CISCO-VOICE-IF-MIB::cvIfCfgInterDigitTimeOut.37 = INTEGER: 10 seconds
CISCO-VOICE-IF-MIB::cvIfCfgInterDigitTimeOut.38 = INTEGER: 10 seconds
CISCO-VOICE-IF-MIB::cvIfCfgRegionalTone.37 = STRING: "US"
CISCO-VOICE-IF-MIB::cvIfCfgRegionalTone.38 = STRING: "US"
CISCO-VOICE-IF-MIB::cvIfCfgEntry.13.37 = INTEGER: 1
CISCO-VOICE-IF-MIB::cvIfCfgEntry.13.38 = INTEGER: 1
CISCO-VOICE-IF-MIB::cvIfCfgEntry.14.37 = INTEGER: 1
CISCO-VOICE-IF-MIB::cvIfCfgEntry.14.38 = INTEGER: 1

Cette sortie affiche le snmpwalk complet du ciscoVoiceDialControlMIB de CISCO-VOICE-DIAL-CONTROL-MIB au moment des commandes de vérification VoIP affichées dans ce document :

snmpwalk -c public 172.16.100.20 CISCO-VOICE-DIAL-CONTROL-MIB:ciscoVoiceDialControlMIB
CISCO-VOICE-DIAL-CONTROL-MIB::cvGeneralPoorQoVNotificationEnable.0 = INTEGER: true(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.1000 = INTEGER: 91
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.2000 = INTEGER: 90
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.1000 = INTEGER: voip(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.2000 = INTEGER: voice(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgRowStatus.1000 = INTEGER: active(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgRowStatus.2000 = INTEGER: active(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgEntry.5.1000 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgEntry.5.2000 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgSessionTarget.90 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDialDigitsPrefix.90 = STRING: 9
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDIDCallEnable.90 = INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgCasGroup.90 = INTEGER: -1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgRegisterE164.90 = INTEGER: true(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgForwardDigits.90 = INTEGER: -1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgEntry.7.90 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionProtocol.91 = INTEGER: cisco(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgDesiredQoS.91 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgMinAcceptableQoS.91 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionTarget.91 = 
STRING: ipv4:172.16.99.22
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgCoderRate.91 = 
INTEGER: g729IETFr8000(16)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgFaxRate.91 = INTEGER: voiceRate(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgVADEnable.91 = INTEGER: true(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgExpectFactor.91 = 
INTEGER: 0 equipment impairment factor (eif)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgIcpif.91 = 
INTEGER: 20 equipment impairment factor (eif)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgPoorQoVNotificationEnable.91 = 
INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgUDPChecksumEnable.91 = INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgIPPrecedence.91 = INTEGER: 0
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgTechPrefix.91 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgDigitRelay.91 = Hex-STRING: 00 
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgCoderBytes.91 = INTEGER: 20 bytes
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgFaxBytes.91 = INTEGER: 20 bytes
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgInBandSignaling.91 = INTEGER: cas(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgEntry.23.91 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgIncomingDnisDigits.90 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgIncomingDnisDigits.91 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgMaxConnections.90 = 
INTEGER: -1 connections
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgMaxConnections.91 = 
INTEGER: -1 connections
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgApplicationName.90 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgApplicationName.91 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.90 = INTEGER: 0
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.91 = INTEGER: 0
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgHuntStop.90 = INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgHuntStop.91 = INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.6.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.6.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.7.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.7.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.8.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.8.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.9.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.9.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.10.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.10.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveConnectionId.1102799.1 = 
Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveTxDuration.1102799.1 = 
Gauge32: 157515460 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveVoiceTxDuration.1102799.1 = 
Gauge32: 157514630 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveFaxTxDuration.1102799.1 = 
Gauge32: 0 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveCoderTypeRate.1102799.1 = 
INTEGER: ietfg729r8000(25)
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveNoiseLevel.1102799.1 = INTEGER: -56 dBm
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveACOMLevel.1102799.1 = INTEGER: 5 dB
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveOutSignalLevel.1102799.1 = 
INTEGER: -46 dBm
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveInSignalLevel.1102799.1 = 
INTEGER: -40 dBm
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveERLLevel.1102799.1 = INTEGER: 5 dB
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveSessionTarget.1102799.1 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveImgPageCount.1102799.1 = Gauge32: 0 pages
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.13.1102799.1 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.14.1102799.1 = INTEGER: 2
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.15.1102799.1 = INTEGER: 19971
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.17.1102799.1 = INTEGER: 5
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveConnectionId.1102966.1 = 
Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteIPAddress.1102966.1 = 
IpAddress: 172.16.99.22
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteUDPPort.1102966.1 = 
INTEGER: 19066
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRoundTripDelay.1102966.1 = 
Gauge32: 6 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSelectedQoS.1102966.1 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSessionProtocol.1102966.1 = 
INTEGER: cisco(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSessionTarget.1102966.1 = 
STRING: ipv4:172.16.99.22
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveOnTimeRvPlayout.1102966.1 = 
Gauge32: 157496940 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithSilence.1102966.1 = 
Gauge32: 1090 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithPrediction.1102966.1 = 
Gauge32: 3680 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithInterpolation.1102966.1 = 
Gauge32: 0 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithRedundancy.1102966.1 = 
Gauge32: 0 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveHiWaterPlayoutDelay.1102966.1 = 
Gauge32: 132 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLoWaterPlayoutDelay.1102966.1 = 
Gauge32: 55 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveReceiveDelay.1102966.1 = 
Gauge32: 67
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveVADEnable.1102966.1 = 
INTEGER: true(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveCoderTypeRate.1102966.1 = 
INTEGER: ietfg729r8000(25)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLostPackets.1102966.1 = 
Gauge32: 52 packets
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEarlyPackets.1102966.1 = 
Gauge32: 1 packets
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLatePackets.1102966.1 = 
Gauge32: 325 packets
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.21.1102966.1 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.22.1102966.1 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.23.1102966.1 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.24.1102966.1 = 
STRING: "172.16.99.22"
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.25.1102966.1 = INTEGER: 1720
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.26.1102966.1 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.27.1102966.1 = 
STRING: "172.16.99.22"
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.28.1102966.1 = INTEGER: 19066

Cette sortie affiche le snmpwalk complet du ciscoVoiceCommonDialControlMIB de CISCO-VOICE-DIAL-CONTROL-MIB au moment des commandes de vérification VoIP affichées dans ce document :

snmpwalk -c public 172.16.100.20 CISCO-VOICE-COMMON-DIAL-CONTROL-MIB:
ciscoVoiceCommonDialControlMIB
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveConnectionId.
1102966.1 = Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveVADEnable.
1102966.1 = INTEGER: true(1)
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCoderTypeRate.
1102966.1 = INTEGER: ietfg729r8000(25)
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCodecBytes.
1102966.1 = INTEGER: 20
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveInBandSignaling.
1102966.1 = INTEGER: cas(1)
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveEntry.6.
1102966.1 = ""
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveEntry.7.
1102966.1 = INTEGER: 2

Cette sortie affiche le snmpwalk complet du dialControlMib du DIAL-CONTROL-MIB au moment des commandes de vérification VoIP affichées dans ce document :

snmpwalk -c public 172.16.100.20 DIAL-CONTROL-MIB:dialControlMib
DIAL-CONTROL-MIB::dialCtlAcceptMode.0 = INTEGER: acceptAll(2)
DIAL-CONTROL-MIB::dialCtlTrapEnable.0 = INTEGER: enabled(1)
DIAL-CONTROL-MIB::dialCtlPeerCfgIfType.1000.91 = INTEGER: voiceOverIp(104)
DIAL-CONTROL-MIB::dialCtlPeerCfgIfType.2000.90 = INTEGER: voiceFXS(102)
DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.2000.90 = INTEGER: 37
DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.1000.91 = STRING: 1000
DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.2000.90 = STRING: 2000
DIAL-CONTROL-MIB::dialCtlPeerCfgAnswerAddress.1000.91 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerCfgAnswerAddress.2000.90 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerCfgSubAddress.1000.91 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerCfgSubAddress.2000.90 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerCfgSpeed.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgSpeed.2000.90 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgInfoType.1000.91 = INTEGER: speech(2)
DIAL-CONTROL-MIB::dialCtlPeerCfgInfoType.2000.90 = INTEGER: speech(2)
DIAL-CONTROL-MIB::dialCtlPeerCfgPermission.1000.91 = INTEGER: both(3)
DIAL-CONTROL-MIB::dialCtlPeerCfgPermission.2000.90 = INTEGER: both(3)
DIAL-CONTROL-MIB::dialCtlPeerCfgInactivityTimer.1000.91 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgInactivityTimer.2000.90 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgMinDuration.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgMinDuration.2000.90 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgMaxDuration.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgMaxDuration.2000.90 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgCarrierDelay.1000.91 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgCarrierDelay.2000.90 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgCallRetries.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgCallRetries.2000.90 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgRetryDelay.1000.91 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgRetryDelay.2000.90 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgFailureDelay.1000.91 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgFailureDelay.2000.90 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgTrapEnable.1000.91 = INTEGER: disabled(2)
DIAL-CONTROL-MIB::dialCtlPeerCfgTrapEnable.2000.90 = INTEGER: disabled(2)
DIAL-CONTROL-MIB::dialCtlPeerCfgStatus.1000.91 = INTEGER: active(1)
DIAL-CONTROL-MIB::dialCtlPeerCfgStatus.2000.90 = INTEGER: active(1)
DIAL-CONTROL-MIB::dialCtlPeerStatsConnectTime.1000.91 = Gauge32: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerStatsConnectTime.2000.90 = Gauge32: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerStatsChargedUnits.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsChargedUnits.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsSuccessCalls.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsSuccessCalls.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsFailCalls.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsFailCalls.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsAcceptCalls.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsAcceptCalls.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsRefuseCalls.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsRefuseCalls.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectCause.1000.91 = ""
DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectCause.2000.90 = ""
DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectText.1000.91 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectText.2000.90 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerStatsLastSetupTime.1000.91 = Timeticks: 
(1102966) 3:03:49.66
DIAL-CONTROL-MIB::dialCtlPeerStatsLastSetupTime.2000.90 = Timeticks: 
(1102799) 3:03:47.99
DIAL-CONTROL-MIB::callActivePeerAddress.1102799.1 = STRING: 2000
DIAL-CONTROL-MIB::callActivePeerAddress.1102966.1 = STRING: 1000
DIAL-CONTROL-MIB::callActivePeerSubAddress.1102799.1 = STRING: 
DIAL-CONTROL-MIB::callActivePeerSubAddress.1102966.1 = STRING: 
DIAL-CONTROL-MIB::callActivePeerId.1102799.1 = INTEGER: 2000
DIAL-CONTROL-MIB::callActivePeerId.1102966.1 = INTEGER: 1000
DIAL-CONTROL-MIB::callActivePeerIfIndex.1102799.1 = INTEGER: 90
DIAL-CONTROL-MIB::callActivePeerIfIndex.1102966.1 = INTEGER: 91
DIAL-CONTROL-MIB::callActiveLogicalIfIndex.1102799.1 = INTEGER: 37
DIAL-CONTROL-MIB::callActiveLogicalIfIndex.1102966.1 = INTEGER: 0
DIAL-CONTROL-MIB::callActiveConnectTime.1102799.1 = Timeticks: 
(1104123) 3:04:01.23
DIAL-CONTROL-MIB::callActiveConnectTime.1102966.1 = Timeticks: 
(1104123) 3:04:01.23
DIAL-CONTROL-MIB::callActiveCallState.1102799.1 = INTEGER: active(4)
DIAL-CONTROL-MIB::callActiveCallState.1102966.1 = INTEGER: active(4)
DIAL-CONTROL-MIB::callActiveCallOrigin.1102799.1 = INTEGER: answer(2)
DIAL-CONTROL-MIB::callActiveCallOrigin.1102966.1 = INTEGER: originate(1)
DIAL-CONTROL-MIB::callActiveChargedUnits.1102799.1 = Gauge32: 0
DIAL-CONTROL-MIB::callActiveChargedUnits.1102966.1 = Gauge32: 0
DIAL-CONTROL-MIB::callActiveInfoType.1102799.1 = INTEGER: speech(2)
DIAL-CONTROL-MIB::callActiveInfoType.1102966.1 = INTEGER: speech(2)
DIAL-CONTROL-MIB::callActiveTransmitPackets.1102799.1 = Gauge32: 7875641
DIAL-CONTROL-MIB::callActiveTransmitPackets.1102966.1 = Gauge32: 7875388
DIAL-CONTROL-MIB::callActiveTransmitBytes.1102799.1 = Gauge32: 157512782
DIAL-CONTROL-MIB::callActiveTransmitBytes.1102966.1 = Gauge32: 157507741
DIAL-CONTROL-MIB::callActiveReceivePackets.1102799.1 = Gauge32: 7875955
DIAL-CONTROL-MIB::callActiveReceivePackets.1102966.1 = Gauge32: 7875641
DIAL-CONTROL-MIB::callActiveReceiveBytes.1102799.1 = Gauge32: 157519081
DIAL-CONTROL-MIB::callActiveReceiveBytes.1102966.1 = Gauge32: 157512782
DIAL-CONTROL-MIB::callHistoryTableMaxLength.0 = INTEGER: 50
DIAL-CONTROL-MIB::callHistoryRetainTimer.0 = INTEGER: 15 minutes

Informations connexes


Document ID: 63607