Voix : Télécopie/modem sur IP

Télécopie OnRamp T.37

17 décembre 2015 - Traduction automatique
Autres versions: PDFpdf | Anglais (22 août 2015) | Commentaires


Contenu


Introduction

Cette section de la télécopie principale au-dessus du document T.37 d'enregistrement et transfert de télécopie IP décrit faxer d'enregistrement et transfert d'OnRamp. L'OnRamp est T.37 le processus de recevoir un appel de télécopie, encodant que télécopie dans un format de fichier d'image étiqueté (tiff), et envoyant ce tiff à un serveur de mail comme connexion.

Ce document contient la configuration exigée pour obtenir la caractéristique opérationnelle. La section de dépannage va au-dessus des commandes de débogage utiles et comment interpréter leur signification. La topologie utilisée est affichée dans la section de schéma de réseau.

Conditions préalables

Conditions requises

Les conditions requises spécifiques pour ce document sont spécifiées dans la section principale, télécopie au-dessus de télécopie T.37 d'enregistrement et transfert IP.

Composants utilisés

Ce document n'est pas limité à des versions de matériel et de logiciel spécifiques.

Les informations contenues dans ce document ont été créées à partir des périphériques d'un environnement de laboratoire spécifique. Tous les périphériques utilisés dans ce document ont démarré avec une configuration effacée (par défaut). Si votre réseau est opérationnel, assurez-vous que vous comprenez l'effet potentiel de toute commande.

Conventions

Pour plus d'informations sur les conventions de documents, reportez-vous à Conventions relatives aux conseils techniques Cisco.

Configuration

Dans les sections ci-dessous, d'abord les paramètres de configuration du logiciel de Cisco IOSÝ concernant la configuration de télécopie d'OnRamp sont expliqués, et alors la configuration 5300 est affichée avec d'autres notes clarifiant les fonctions d'importantes commandes. Quelques paramètres de configuration facultatifs peuvent être trouvés dans la section qui suit la configuration 5300.

Diagramme du réseau

Ce document utilise la configuration réseau indiquée dans le diagramme suivant :

/image/gif/paws/47763/onramp_faxing1.gif

Paramètres de configuration

Paramètres obligatoires :
télécopie-messagerie de fax interface-type D'enables fonctionnalité T.37 pour la passerelle. Exige une réinitialisation sur les 5300, mais pas les 5350 ou les 5400.
mta send server C'est l'adresse Internet ou adresse IP du serveur de Protocole SMTP (Simple Mail Transfer Protocol) que le routeur va envoyer l'email d'OnRamp. Sans cette configuration, le routeur ne sait pas où envoyer l'email d'OnRamp. Voyez que l'aucune section configurée par serveur pour ne met au point et les messages console sans serveur configuré.
mta send postmaster Cette adresse est utilisée si messagerie-de options envoyé par MTA n'évaluent pas ou ne sont pas configurés. Il est placé dans l'email d'OnRamp du champ. C'est facultatif si le nom d'utilisateur de mta send mail-from et l'adresse Internet de mta send mail-from sont présents. A cliquez ici pour mettent au point le mspi pour un appel défaillant.
ip domain-name Utilisé pour identifier l'expéditeur d'email dans le message d'HÉLICOPTÈRE avec hostname.domain-name. Le routeur doit être rechargé après que cette commande soit configurée.
onramp flash:app_libretto_onramp.2.0.1.1.tcl de call application voice Définit un nom global pour l'application (onramp, dans ce cas) et son emplacement (dans l'éclair du routeur, dans ce cas).
onramp d'application de pots du dial-peer voice 8913180 Appelle l'onramp d'application quand ce cadran-pair est apparié.
fax_on_vfc_onramp_app d'application de mmoip du dial-peer voice 1 en partance Application à s'appeler quand ce pair de messagerie multimédias sur IP (MMoIP) est apparié. Pré-empaqueté en logiciel de Cisco IOS. Résumé traversant visible de show call application voice.
Paramètres optionnels :
adresse Internet de mta send mail-from C'est l'adresse Internet à utiliser dans du champ dans l'email d'OnRamp. Obligatoire si la commande de mta send postmaster n'est pas présente. Doit être configuré si le nom d'utilisateur de mta send mail-from est utilisé.
nom d'utilisateur de mta send mail-from C'est le créateur à utiliser dans du champ dans l'email d'OnRamp. Utilisé en même temps que l'adresse Internet de mta send mail-from pour obtenir entier du champ - c.-à-d., username@hostname. Obligatoire si la commande de mta send postmaster n'est pas présente. Doit être configuré si l'adresse Internet de mta send mail-from est utilisée.
mta send subject Chaîne de texte à utiliser dans le champ Subject dans l'email d'OnRamp.
le MTA envoient l'avec-sujet
  • Ajoute le numéro de l'appelant avec le mot clé $s$.
  • Ajoute le numéro appelé avec le mot clé $d$.
  • Ajoute appeler et numéro appelé avec le mot clé chacun des deux.
Pour mettez au point l'affichage, a cliquez ici.
mta send return-receipt-to Les mots clé sont nom d'utilisateur et adresse Internet. Ensemble ils forment disposition-notification-à : username@hostname.
mdn de mmoip de nombre de dial-peer voice Demande qu'un email envoyé par ce pair de MMoIP demande une notification de disposition de message (MDN) soit envoyé au desitnation definted par la commande de mta send return-receipt-to.
dsn de mmoip de nombre de dial-peer voice {retard | succès | panne} Demande qu'un avis d'état de la livraison (DSN) soit envoyé à la destination définie par la commande de mta send mail-from

Configuration d'OnRamp

vdtl-5300-7a# show running-config 
Building configuration...

Current configuration : 2294 bytes
!
! Last configuration change at 10:49:16 EST Mon Mar 18 2003
! NVRAM config last updated at 11:00:42 EST Mon Mar 4 2003
!
version 12.2
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
no service password-encryption
!
hostname vdtl-5300-7a
!
!
resource-pool disable
clock timezone EST -5
!
ip subnet-zero
ip domain-name testlab-t37.com

!--- The ip domain-name command is needed so the router sends a fully qualified
!--- domain-name (FQDN) to the email server.
  

!--- Router must be reloaded after ip domain-name configuration due to a known bug
!--- that has since been resolved.

ip name-server 172.18.106.36

!--- The ip name-server command is required in order to do name resolution.

!
!
isdn switch-type primary-5ess
!
fax receive called-subscriber 8913180
fax interface-type fax-mail
! 
mta send server testlab-smtp.testlab-t37.com port 25

!--- The mta send server command identifies the email server for OnRamp emails.
 
! 
mta send subject Fax from On-Ramp GW vdlt-5300-7a
mta send with-subject both
mta send postmaster administrator@testlab-t37.com
!

!--- The address set with mta send postmaster is used as the "From" address
!--- unless mta send mail-from commands are defined.
 
! 
mta send mail-from hostname vdtl-5300-7a.testlab-t37.com
mta send mail-from username $s$
mta send return-receipt-to hostname testlab-t37.com
mta send return-receipt-to username admin
mta receive maximum-recipients 0
call-history-mib retain-timer 500
!
controller T1 0
framing esf
clock source line primary
linecode b8zs
pri-group timeslots 1-24
!
!
!
interface Ethernet0
ip address 15.80.7.11 255.255.255.0
!
interface Serial0:23
no ip address
isdn switch-type primary-5ess
isdn incoming-voice modem
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 15.80.7.1
no ip http server
ip pim bidir-enable
!
call rsvp-sync
!
call application voice onramp flash:app_libretto_onramp.2.0.1.1.tcl

!--- This identifies the call application to use. It is named "onramp" in
!--- this example.

voice-port 0:D 
!
mgcp profile default
!
dial-peer voice 1 mmoip
application fax_on_vfc_onramp_app out-bound
destination-pattern 8913144
information-type fax
session target mailto:$d$@testlab-t37.com 
!

!--- The MMoIP peers contain configuration specific to the called party number.
!--- It requests MDN and DSN. It identifies the application to use for the outbound
!--- call leg and specifies the address to which the email will be sent.
 
mdn
dsn success
dsn failure
! 
dial-peer voice 891314 pots
application onramp
incoming called-number 891314[4-5]
direct-inward-dial
port 0:D

!--- The pots peers for T.37 are no different than for voice calls with the exception of
!--- using the application defined above in the call application global configuration
!--- command. The direct-inward-dial command is required unless using a redialer.

!
line con 0
exec-timeout 0 0
line aux 0
line vty 0 4
login
!
ntp clock-period 17179806
ntp server 172.18.106.15
end

vdtl-5300-7a#

Configuration facultative

Voici quelques paramètres de configuration facultatifs. Le premier exemple t'affiche comment configurer de plusieurs comptes de messagerie utilisant les adresses e-mail traditionnelles, et le deuxième exemple t'affiche comment configurer de plusieurs comptes de messagerie utilisant des numéros appelés pour des adresses e-mail.

Exemple 1 :

!
dial-peer voice 1 mmoip
 application fax_on_vfc_onramp_app out-bound
 destination-pattern 8913144
 information-type fax
 session target mailto:andy@testlab-t37.com
!
dial-peer voice 2 mmoip
 application fax_on_vfc_onramp_app out-bound
 destination-pattern 8913145
 information-type fax
 session target mailto:bobby@testlab-t37.com
!
dial-peer voice 891314 pots
 application onramp
 incoming called-number 891314[4-5]
 direct-inward-dial
 port 0:D
!
Dans cette configuration, le PRI a deux nombres de sélection directe à l'arrivée (A FAIT) : 891-3144 et 891-3145. Selon quel numéro est composé, un email est envoyé à andy@testlab-t37.com ou à bobby@testlab-t37.com.

Exemple 2 :

!
dial-peer voice 1 mmoip
application fax_on_vfc_onramp_app out-bound
destination-pattern 8913144
information-type fax
session target mailto:$d$@testlab-t37.com
!
Avec cette configuration, le Service d'identification du numéro composé réacheminé (RDNIS) (numéro appelé) est inséré dans le RCPT À : Commande de SMTP. Ceci permet à des clients pour donner chaque utilisateur qu'a A FAIT pour des applications d'OnRamp. Ils ajoutent simplement un pseudonyme sur le serveur de mail. 12 mars 15:42:12.947 : (C) S : RCPT TO:<FAX=8913144@testlab-t37.com>

Remarque: Assurez-vous que l'email alias est FAX=8913144@domain.com au lieu de 8913144@domain.com ou l'email ne sera pas fourni correctement.

Dépannez

Debugs défectueux

Remarque: Des modifications de configuration sont notées au-dessus du met au point.

debug mspi send
!
fax interface-type fax-mail
mta send server testlab-smtp.testlab-t37.com port 25
mta send mail-from hostname whatever.com
mta receive maximum-recipients 0
call-history-mib retain-timer 500
! 

Remarque: La commande de nom d'utilisateur de mta send mail-from est omise de la configuration, de même que la commande de mta send postmaster.

vdtl-5300-7a#
Mar 4 10:03:29.165: mspi_setup_req: for cid=0x27
Mar 4 10:03:29.165: envelope_from=FAX=@        
!--- Note: This is not a valid email address (no domain).

Mar 4 10:03:29.165: envelope_to=andy@testlab-t37.com
Mar 4 10:03:30.165: mspi_chk_connect: cid=0x27, cnt=0, 
Mar 4 10:03:30.165: SMTP connected to the server !  
!--- The connection to the SMTP server is initiated.

Mar 4 10:03:30.165: mspi_bridge: cid=0x27, dst cid=0x28,
Mar 4 10:03:56.985: mspi_xmit: cid=0x27, st=CONFERENCED, src_cid=0x28, buf cnt=0
Mar 4 10:03:56.985: %MSPI-4-MSPI_NO_SMTP_SEND: MSPI- Could not
 send data to the SMTP server, cid=39, mspi_on_xmit, lost connection
Mar 4 10:03:56.985: mspi_on_xmit: cid=0x27, lost connection
Mar 4 10:03:56.985: disc text=no route to destination (3): SMTP client engine
 lost connection  
!--- The statement "no route to destination" is a little misleading as a cause code.

Mar 4 10:03:56.985: mspi_xmit: cid=0x27, st=ABORTING, src_cid=0x28
Mar 4 10:03:56.985: discarding buffer

!--- Several lines of mspi_xmit debugs that were identical to the lines above
!--- and below this note have been suppressed.

Mar 4 10:03:56.989: mspi_xmit: cid=0x27, st=ABORTING, src_cid=0x28
Mar 4 10:03:56.993: discarding buffer
Mar 4 10:03:56.993: %LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT: ESMTP client
 did not connect or lost connection to remote server
Mar 4 10:03:56.993: mspi_bridge_drop: cid=0x27, dst cid=0x28, st=ABORTING, onramp
Mar 4 10:03:56.993: mspi_disconnect: cid=0x27, st=DISCONNECTING, cause=no route to
 destination (3)
Mar 4 10:03:56.993: mspi_on_call_hist: cid=0x27, cause=no route to destination (3):
 SMTP client engine lost connection
Mar 4 10:03:56.993: disposing smtp ctx
Mar 4 10:03:56.993: mspi_free_ccb: mmccb allocated=1, inserted=0
vdtl-5300-7a#

Le même problème peut être vu qu'un peu plus clair avec ceci mettez au point :

vdtl-5300-7a# debug mta send all
Mar 5 16:48:46.420: esmtp_client_engine_open: from=FAX=@, to=andy@testlab-t37.com
Mar 5 16:48:46.420: esmtp_client_engine_add_headers: from_comment=Fax 
Mar 5 16:48:46.792: esmtp_client_work: socket 0 attempting to connect to IP
 address 172.18.106.36
Mar 5 16:48:46.792: esmtp_client_work: socket 0 readable for first time
Mar 5 16:48:46.792: esmtp_client_work: socket 0 readable for first time
Mar 5 16:48:46.796: (C)R: 220 testlab-smtp.testlab-t37.com Microsoft ESMTP MAIL Service,
 Version: 5.0.2195.4453 ready at Tue, 5 Mar 2002 16:48:12 -0500 
!--- This is the SMTP server information displayed with the login.

Mar 5 16:48:46.796: (C)S: EHLO vdtl-5300-7a.testlab-t37.com
Mar 5 16:48:47.208: (C)R: 250-testlab-smtp.testlab-t37.com Hello [15.80.7.11]

!--- All the responses through the R: 250 OK are in response to the EHLO command from
!--- the sender (the 5300). These are the capabilities of the receiver.

Mar 5 16:48:47.208: (C)R: 250-TURN
Mar 5 16:48:47.208: (C)R: 250-ATRN 
Mar 5 16:48:47.208: (C)R: 250-SIZE
Mar 5 16:48:47.208: (C)R: 250-ETRN 
Mar 5 16:48:47.212: (C)R: 250-PIPELINING
Mar 5 16:48:47.212: (C)R: 250-DSN
Mar 5 16:48:47.212: (C)R: 250-ENHANCEDSTATUSCODES
Mar 5 16:48:47.212: (C)R: 250-8bitmime                                                          
Mar 5 16:48:47.212: (C)R: 250-BINARYMIME                                              
Mar 5 16:48:47.212: (C)R: 250-CHUNKING                                                             
Mar 5 16:48:47.212: (C)R: 250-VRFY                                                             
Mar 5 16:48:47.212: (C)R: 250-X-EXPS GSSAPI NTLM LOGIN                   
Mar 5 16:48:47.212: (C)R: 250-X-EXPS=LOGIN                                            
Mar 5 16:48:47.212: (C)R: 250-AUTH GSSAPI NTLM LOGIN                      
Mar 5 16:48:47.212: (C)R: 250-AUTH=LOGIN                                              
Mar 5 16:48:47.212: (C)R: 250-X-LINK2STATE                                           
Mar 5 16:48:47.212: (C)R: 250-XEXCH50                                                     
Mar 5 16:48:47.212: (C)R: 250 OK                                                                 
Mar 5 16:48:47.212: (C)S: MAIL FROM:<FAX=@>                                    
!--- This is the mail from command.

Mar 5 16:48:47.708: (C)R: 501 5.5.4 Invalid Address                                    
!--- The server does not like the address.

Mar 5 16:48:47.708: esmtp_client_work: error in response to MAIL FROM  
!--- This tells exactly where the problem ocurred in the SMTP exchange.

Mar 5 16:48:47.708: esmtp_client_work: ERROR, socket=0
Mar 5 16:49:15.132: %MSPI-4-MSPI_NO_SMTP_SEND: MSPI- Could not
send data to the SMTP server, cid=96, mspi_on_xmit, lost connection
Mar 5 16:49:15.132: %LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT: ESMTP client did not
 connect or lost connection to remote server
Mar 5 16:49:15.208: esmtp_client_work: Freeing ctx=0x62616C4C
Mar 5 16:49:15.208: esmtp_client: returned from work, context freed

Aucun serveur configuré

fax receive called-subscriber 8913180
fax interface-type fax-mail
mta send subject Fax from On-Ramp GW vdlt-5300-7a
mta send postmaster administrator@testlab-t37.com
mta send mail-from hostname vdtl-5300-7a.testlab-t37.com
mta send mail-from username $s$
mta receive maximum-recipients 0

vdtl-5300-7a#
Mar 4 10:46:48.703: mspi_setup_req: for cid=0x3F
Mar 4 10:46:48.703: %MSPI-1-MSPI_BAD_CONFIG: MSPI-bad configuration, mspi_setup_req:
 NULL server ip address
Mar 4 10:46:48.703: mspi_setup_req: NULL server address
Mar 4 10:46:48.703: %LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT: ESMTP client
 did not connect or lost connection to remote server
vdtl-5300-7a# 

Le serveur configuré mais aucune artère IP au serveur n'existe

vdtl-5300-7a# debug mspi send 
Mail SPI send debugging is on
vdtl-5300-7a#
Mar 20 09:35:27.126: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 20 09:35:29.306: mspi_setup_req: for cid=0x141
Mar 20 09:35:29.306: envelope_from=FAX=8915510@vdtl-5300-7a.testlab-t37.com
Mar 20 09:35:29.310: envelope_to=FAX=8913144@testlab-t37.com
Mar 20 09:35:30.310: mspi_chk_connect: cid=0x141, cnt=0, 
Mar 20 09:35:30.310: SMTP is in the error state...
Mar 20 09:35:30.310: disc text=no route to destination (3): SMTP client open failed
Mar 20 09:35:30.310: Still waiting for the SMTP connection.....  
!--- You can tell that the SMTP connection was never established.

Mar 20 09:35:30.310: %LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT: ESMTP client
 did not connect or lost connection to remote server
Mar 20 09:35:30.310: mspi_disconnect: cid=0x141, st=DISCONNECTING, cause=no route
 to destination (3)  
!--- This cause code seems to be an accurate description of the problem.

Mar 20 09:35:30.310: mspi_on_call_hist: cid=0x141, cause=no route to destination (3):
 SMTP client open failed
Mar 20 09:35:30.310: disposing smtp ctx
Mar 20 09:35:30.310: mspi_free_ccb: mmccb allocated=1, inserted=0
Mar 20 09:35:36.006: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510,
 call lasted 14 seconds
vdtl-5300-7a#

Remarque: Le routeur n'envoie pas un nom de domaine complet (FQDN) au Ms Exchange Server et il ne fait pas comme la syntaxe. C'est parce que le routeur a besoin d'une recharge après avoir ajouté le « domaine d'ip domain-name »

vdtl-5300-7a# debug mmoip send email andy@testlab-t37.com
vdtl-5300-7a#
Mar 28 09:55:16.768: %SYS-5-CONFIG_I: Configured from console by console
Mar 28 09:55:17.936: esmtp_client_engine_open: from=testing@vdtl-5300-7a.testlab-t37.com,
 to=andy@testlab-t37.com
Mar 28 09:55:17.940: esmtp_client_engine_add_headers: from_comment=mspi Test User
Mar 28 09:55:18.072: esmtp_client_work: socket 0 attempting to connect to IP
 address 172.18.106.36
Mar 28 09:55:18.072: esmtp_client_work: socket 0 readable for first time
Mar 28 09:55:18.072: esmtp_client_work: socket 0 readable for first time
Mar 28 09:55:18.076: (C)R: 220 testlab-smtp.testlab-t37.com Microsoft ESMTP MAIL Service,
 Version: 5.0.2195.4453 ready at Thu, 28 Mar 2002 09:54:02 -0500 
Mar 28 09:55:18.076: (C)S: EHLO vdtl-5300-7a.  
!--- The Exchange server does not like the trailing dot (.).

Mar 28 09:55:18.484: (C)R: 501 5.5.4 Invalid Address
Mar 28 09:55:18.484: esmtp_client_work: EHLO failed; will try sending HELO
Mar 28 09:55:18.484: (C)S: HELO vdtl-5300-7a.
Mar 28 09:55:18.984: (C)R: 501 5.5.4 Invalid Address
Mar 28 09:55:18.984: esmtp_client_work: error in response to HELO
Mar 28 09:55:18.984: esmtp_client_work: ERROR, socket=0
Mar 28 09:55:18.984: esmtp_client_work: Freeing ctx=0x62661F18
Mar 28 09:55:18.988: esmtp_client: returned from work, context freed
vdtl-5300-7a#

Fonctionner des debugs

Ces commandes de débogage sont utilisées pour le côté de SMTP de l'OnRamp :

vdtl-5300-7a# debug foip on-ramp 
FOIP On ramp faxmail debugging is on
vdtl-5300-7a#
Mar 18 10:57:50.995: lapp_on_application: Incoming Event: (15 = CC_EV_CALL_HANDOFF),
 CID(216), DISP(0)
Mar 18 10:57:50.995: lapp_on_call_handoff: Authentication enabled = FALSE
Mar 18 10:57:50.995: lapp_on_call_handoff: Authentication ID = 0
Mar 18 10:57:50.995: lapp_on_call_handoff: Authentication ID source = IVR or unknown
Mar 18 10:57:50.999: lapp_on_call_handoff: Authentication status = SUCCESS
Mar 18 10:57:50.999: lapp_on_call_handoff: Accounting enabled = FALSE
Mar 18 10:57:50.999: lapp_on_call_handoff: Accounting method list = fax
Mar 18 10:57:50.999: lapp_on_call_handoff: Mailto Address = 
Mar 18 10:57:50.999: lapp_on_conference_vtsp_fmsp: Begin conferencing VTSP and FMSP... 
Mar 18 10:57:50.999: lapp_on_change_state: old state(0) new state(1) 
!--- HANDOFF to VTSP_FMSP_CONFERENCING

Mar 18 10:57:51.003: lapp_on_application: Incoming Event: (29 = CC_EV_CONF_CREATE_DONE),
 CID(216), DISP(0)
Mar 18 10:57:51.003: lapp_on_application: Current call state = 1 
Mar 18 10:57:51.003: lapp_on_conference_created: The VTSP and the FMSP are conferenced
Mar 18 10:57:51.003: lapp_on_conference_created: Wait for FMSP call detail event
Mar 18 10:57:51.003: lapp_on_change_state: old state(1) new state(2) 
!--- VTSP_FMSP_CONFERENCING to FMSP_CALL_DETAIL

Mar 18 10:57:57.075: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 18 10:57:59.135: lapp_on_application: Incoming Event: (33 = CC_EV_FROM_FMSP_ON_CALL_DETAIL),
 CID(217), DISP(0)
Mar 18 10:57:59.139: lapp_on_application: Current call state = 2 
Mar 18 10:57:59.139: lapp_on_msp_event: Incoming call detail has arrived from the FMSP
Mar 18 10:57:59.139: lapp_on_setup_mspi: Prep MSPI ccCallSetupRequest... 
Mar 18 10:57:59.139: lapp_on_setup_mspi: Envelope from: FAX=8915510@vdtl-5300-7a.testlab-t37.com
Mar 18 10:57:59.139: lapp_on_setup_mspi: Envelope to: FAX=8913144@testlab-t37.com
Mar 18 10:57:59.139: lapp_on_setup_mspi: rfc822_to_comment: 8913144
Mar 18 10:57:59.139: lapp_on_setup_mspi: Faxmail subject: Fax from On-Ramp GW vdlt-5300-7a
[DNIS=8913144][ANI=8915510]
Mar 18 10:57:59.139: lapp_on_setup_mspi: Disposition notification to: admin@testlab-t37.com

!--- A read receipt is sent to admin@testlab-t37.com if the reader so chooses.

Mar 18 10:57:59.139: lapp_on_setup_mspi: Originator's TSI = rfc822_from_comment = Fax 
Mar 18 10:57:59.139: lapp_on_setup_mspi: Auth/Account ID = 0
Mar 18 10:57:59.139: lapp_on_setup_mspi: Do ccCallSetupRequest to MSPI
Mar 18 10:57:59.139: lapp_on_conference_fmsp_dmsp: Starting conference with FMSP and DMSP
Mar 18 10:57:59.139: lapp_on_conference_fmsp_dmsp: tiff file created = 2002:03:18 10:57:59
Mar 18 10:57:59.139: lapp_on_change_state: old state(2) new state(3)  
!--- FMSP_CALL_DETAIL to FMSP_DMSP_CONFERENCING

Mar 18 10:57:59.139: lapp_on_application: Incoming Event: (29 = CC_EV_CONF_CREATE_DONE),
 CID(217), DISP(0)
Mar 18 10:57:59.139: lapp_on_application: Current call state = 3 
Mar 18 10:57:59.139: lapp_on_conference_created: The FMSP and the DMSP are conferenced
Mar 18 10:57:59.139: lapp_on_conference_created: Sending
 CC_EV_TO_FMSP_ON_RECEIVE_ENABLE to FMSP
Mar 18 10:57:59.139: lapp_on_change_state: old state(3) new state(4)    
!--- FMSP_DMSP_CONFERENCING to FMSP_PAGE_ACCEPT_REQUESTED

Mar 18 10:58:00.139: lapp_on_application: Incoming Event: (8 = CC_EV_CALL_CONNECTED),
 CID(218), DISP(0)
Mar 18 10:58:00.139: lapp_on_application: Current call state = 4 
Mar 18 10:58:00.139: lapp_on_call_connected: Call connected event received.... - CID(218)
Mar 18 10:58:00.139: lapp_on_call_connected: MSPI call connected - CID(218)
Mar 18 10:58:00.139: lapp_on_call_connected: Start conferencing the DMSP and the MSPI
Mar 18 10:58:00.139: lapp_on_application: Incoming Event: (29 = CC_EV_CONF_CREATE_DONE),
 CID(219), DISP(0)
Mar 18 10:58:00.139: lapp_on_application: Current call state = 4 
Mar 18 10:58:11.539: lapp_on_application: Incoming Event:
 (36 = CC_EV_FROM_FMSP_ON_PAGE_ACCEPT_REQUESTED), CID(217), DISP(0)
Mar 18 10:58:11.539: lapp_on_application: Current call state = 4 
Mar 18 10:58:11.539: lapp_on_msp_event: Page accept request arrived from fmsp
Mar 18 10:58:11.539: lapp_on_msp_event: Sending page accept event to the FMSP
Mar 18 10:58:11.539: lapp_on_msp_event: Pages processed = 1

!--- The first fax page is received.

Mar 18 10:58:11.539: lapp_on_change_state: old state(4) new state(4)
Mar 18 10:58:16.015: lapp_on_application: Incoming Event:
 (37 = CC_EV_FROM_DMSP_ON_PAGE_PROCESSED), CID(219), DISP(146)
Mar 18 10:58:16.015: lapp_on_application: Current call state = 4 
Mar 18 10:58:16.015: lapp_on_msp_event: Page processed event arrived from the DMSP
Mar 18 10:58:16.015: lapp_on_change_state: old state(4) new state(4)
Mar 18 10:58:30.719: lapp_on_application: Incoming Event:
 (36 = CC_EV_FROM_FMSP_ON_PAGE_ACCEPT_REQUESTED), CID(217), DISP(0)
Mar 18 10:58:30.719: lapp_on_application: Current call state = 4 
Mar 18 10:58:30.719: lapp_on_msp_event: Page accept request arrived from fmsp
Mar 18 10:58:30.719: lapp_on_msp_event: Sending page accept event to the FMSP
Mar 18 10:58:30.719: lapp_on_msp_event: Pages processed = 2

!--- The second fax page is received.

Mar 18 10:58:30.719: lapp_on_change_state: old state(4) new state(4)
Mar 18 10:58:32.199: lapp_on_application: Incoming Event:
 (37 = CC_EV_FROM_DMSP_ON_PAGE_PROCESSED), CID(219), DISP(0)
Mar 18 10:58:32.199: lapp_on_application: Current call state = 4 
Mar 18 10:58:32.199: lapp_on_msp_event: Page processed event arrived from the DMSP
Mar 18 10:58:32.199: lapp_on_change_state: old state(4) new state(4)
Mar 18 10:58:34.355: lapp_on_application: Incoming Event: (11 = CC_EV_CALL_DISCONNECTED),
 CID(218), DISP(0)
Mar 18 10:58:34.355: lapp_on_application: Current call state = 4 
Mar 18 10:58:34.355: lapp_on_call_disconnected: Call Disconnected - CID= 218 cause=
 0x10 call_state= 4
Mar 18 10:58:34.355: lapp_on_call_disconnected: MSPI disconnected
Mar 18 10:58:34.355: lapp_on_call_disconnected: Faxmail acknowledged by remote SMTP server
Mar 18 10:58:34.355: lapp_on_change_state: old state(4) new state(7)  
!--- FMSP_PAGE_ACCEPT_REQUESTED to CONFERENCE_DESTROYING

Mar 18 10:58:34.355: lapp_on_conference_cleanup: Destroying conferences... 
Mar 18 10:58:34.355: lapp_on_conference_cleanup: Destroying conference for VTSP & FMSP
Mar 18 10:58:34.355: lapp_on_conference_cleanup: Destroying conference for FMSP & DMSP
Mar 18 10:58:34.355: lapp_on_conference_cleanup: Destroying conference for DMSP & MSPI
Mar 18 10:58:34.355: lapp_on_application: Incoming Event: (30 = CC_EV_CONF_DESTROY_DONE),
 CID(217), DISP(0)
Mar 18 10:58:34.355: lapp_on_application: Current call state = 7 
Mar 18 10:58:34.355: lapp_on_conference_destroyed: FMSP/DMSP conference destroyed
Mar 18 10:58:34.355: lapp_on_conference_destroyed: Conference destroyed..... confID = 150
Mar 18 10:58:34.355: lapp_on_application: Incoming Event: (30 = CC_EV_CONF_DESTROY_DONE),
 CID(219), DISP(0)
Mar 18 10:58:34.355: lapp_on_application: Current call state = 7 
Mar 18 10:58:34.355: lapp_on_conference_destroyed: DMSP/MSPI conference destroyed
Mar 18 10:58:34.355: lapp_on_conference_destroyed: Conference destroyed..... confID = 151
Mar 18 10:58:34.355: lapp_on_application: Incoming Event: (30 = CC_EV_CONF_DESTROY_DONE),
 CID(216), DISP(0)
Mar 18 10:58:34.355: lapp_on_application: Current call state = 7 
Mar 18 10:58:34.355: lapp_on_conference_destroyed: VTSP/FMSP conference destroyed
Mar 18 10:58:34.355: lapp_on_conference_destroyed: Conference destroyed..... confID = 149
Mar 18 10:58:34.355: lapp_on_change_state: old state(7) new state(8)  
!--- CONFERENCE_DESTROYING to DISCONNECTING

Mar 18 10:58:34.355: lapp_on_conference_destroyed: All conferences are destroyed. 
Mar 18 10:58:34.355: lapp_on_change_state: old state(8) new state(8)
Mar 18 10:58:34.355: lapp_on_call_leg_cleanup: Sending disconnect for FMSP
Mar 18 10:58:34.359: lapp_on_call_leg_cleanup: Sending disconnect for DMSP
Mar 18 10:58:34.359: lapp_on_application: Incoming Event:
 (12 = CC_EV_CALL_DISCONNECT_DONE), CID(219), DISP(0)
Mar 18 10:58:34.359: lapp_on_application: Current call state = 8 
Mar 18 10:58:34.359: lapp_on_disconnect_done: Received call disconnect done ... callID = 219
Mar 18 10:58:34.359: lapp_on_disconnect_done: DMSP disconnect done
Mar 18 10:58:34.359: lapp_on_disconnect_done: Sending disconnect for MSPI
Mar 18 10:58:34.359: lapp_on_application: Incoming Event:
 (12 = CC_EV_CALL_DISCONNECT_DONE), CID(218), DISP(0)
Mar 18 10:58:34.359: lapp_on_application: Current call state = 8 
Mar 18 10:58:34.359: lapp_on_disconnect_done: Received call disconnect done ... callID = 218
Mar 18 10:58:34.359: lapp_on_disconnect_done: MSPI disconnect done
Mar 18 10:58:34.363: lapp_on_application: Incoming Event:
 (12 = CC_EV_CALL_DISCONNECT_DONE), CID(217), DISP(0)
Mar 18 10:58:34.363: lapp_on_application: Current call state = 8 
Mar 18 10:58:34.363: lapp_on_disconnect_done: Received call disconnect done ... callID = 217
Mar 18 10:58:34.363: lapp_on_disconnect_done: FMSP disconnect done
Mar 18 10:58:34.363: lapp_on_disconnect_done: Sending disconnect for VTSP
Mar 18 10:58:36.627: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 45 seconds
Mar 18 10:58:37.647: lapp_on_application: Incoming Event: (28 = CC_EV_CALL_FEATURE),
 CID(216), DISP(0)
Mar 18 10:58:37.647: lapp_on_application: Current call state = 8 
Mar 18 10:58:37.647: lapp_on_event_unsupported: Unsupported event received--- 
Mar 18 10:58:37.647: lapp_on_event_unsupported: EV(28=CC_EV_CALL_FEATURE),
 CID(216), disp(0)
Mar 18 10:58:37.647: lapp_on_event_unsupported: Current call state = 8 
Mar 18 10:58:37.651: lapp_on_application: Incoming Event:
 (12 = CC_EV_CALL_DISCONNECT_DONE), CID(216), DISP(0)
Mar 18 10:58:37.651: lapp_on_application: Current call state = 8 
Mar 18 10:58:37.651: lapp_on_disconnect_done: Received call disconnect done ... callID = 216
Mar 18 10:58:37.651: lapp_on_disconnect_done: VTSP disconnect done
Mar 18 10:58:37.651: lapp_on_disconnect_done: All the calls are now void or disconnected
Mar 18 10:58:37.651: lapp_on_change_state: old state(8) new state(9)
!---  DISCONNECTING to TERMINAL

Mar 18 10:58:37.651: lapp_on_call_terminate: Freeing the IVR call handoff record
Mar 18 10:58:37.655: lapp_on_call_terminate: Freeing the fax call record
vdtl-5300-7a#

/image/gif/paws/47763/onramp_faxing2.gif

Le client recevant l'email voit une fenêtre semblable à celle ci-dessus en ouvrant un email avec un positionnement de MDN. La réponse que le demandeur reçoit est sous forme d'email envoyé à l'utilisateur avec le texte du message qui lit, « ceci est une réception pour l'email que vous avez envoyé à "8913144" <Fax=8913144@testlab-t37.com> à 3/18/2002 10:58AM. Cette réception vérifie que le message a été affiché sur l'ordinateur du destinataire à 3/18/2002 11:07 AM. »

vdtl-5300-7a# debug mta send all 
All email send debugging is on
vdtl-5300-7a#
Mar 18 14:50:46.278: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 18 14:50:48.474: esmtp_client_engine_open:
 from=FAX=8915510@vdtl-5300-7a.testlab-t37.com, to=FAX=8913144@testlab-t37.com
Mar 18 14:50:48.474: esmtp_client_engine_add_headers: from_comment=Fax 
Mar 18 14:50:48.702: esmtp_client_work: socket 0 attempting to connect to
 IP address 172.18.106.36
Mar 18 14:50:48.702: esmtp_client_work: socket 0 readable for first time
Mar 18 14:50:48.702: esmtp_client_work: socket 0 readable for first time
Mar 18 14:50:48.706: (C)R: 220 testlab-smtp.testlab-t37.com Microsoft ESMTP MAIL Service,
 Version: 5.0.2195.4453 ready at Mon, 18 Mar 2002 14:49:51 -0500 
Mar 18 14:50:48.706: (C)S: EHLO vdtl-5300-7a.testlab-t37.com
Mar 18 14:50:49.166: (C)R: 250-testlab-smtp.testlab-t37.com Hello [15.80.7.11]
Mar 18 14:50:49.166: (C)R: 250-TURN
Mar 18 14:50:49.170: (C)R: 250-ATRN
Mar 18 14:50:49.170: (C)R: 250-SIZE
Mar 18 14:50:49.170: (C)R: 250-ETRN
Mar 18 14:50:49.170: (C)R: 250-PIPELINING
Mar 18 14:50:49.170: (C)R: 250-DSN
Mar 18 14:50:49.170: (C)R: 250-ENHANCEDSTATUSCODES
Mar 18 14:50:49.170: (C)R: 250-8bitmime
Mar 18 14:50:49.170: (C)R: 250-BINARYMIME
Mar 18 14:50:49.170: (C)R: 250-CHUNKING
Mar 18 14:50:49.170: (C)R: 250-VRFY
Mar 18 14:50:49.170: (C)R: 250-X-EXPS GSSAPI NTLM LOGIN
Mar 18 14:50:49.170: (C)R: 250-X-EXPS=LOGIN
Mar 18 14:50:49.170: (C)R: 250-AUTH GSSAPI NTLM LOGIN
Mar 18 14:50:49.170: (C)R: 250-AUTH=LOGIN
Mar 18 14:50:49.170: (C)R: 250-X-LINK2STATE
Mar 18 14:50:49.170: (C)R: 250-XEXCH50
Mar 18 14:50:49.170: (C)R: 250 OK
Mar 18 14:50:49.170: (C)S: MAIL FROM:<FAX=8915510@vdtl-5300-7a.testlab-t37.com> RET=HDRS
Mar 18 14:50:49.666: (C)R: 250 2.1.0 FAX=8915510@vdtl-5300-7a.testlab-t37.com....Sender OK
Mar 18 14:50:49.666: (C)S: RCPT TO:<FAX=8913144@testlab-t37.com> NOTIFY=SUCCESS,FAILURE
 ORCPT=rfc822;FAX+3D8915510@vdtl-5300-7a.testlab-t37.com
Mar 18 14:50:50.170: (C)R: 250 2.1.5 FAX=8913144@testlab-t37.com 
Mar 18 14:50:50.698: (C)R: 354 Start mail input; end with <CRLF>.<CRLF>
Mar 18 14:50:50.698: (C)S: Received: by vdtl-5300-7a.testlab-t37.com for
 <FAX=8913144@testlab-t37.com> (with Cisco NetWorks); Mon, 18 Mar 2002 14:50:50 -0500
Mar 18 14:50:50.698: (C)S: To: "8913144" <FAX=8913144@testlab-t37.com>
Mar 18 14:50:50.698: (C)S: Message-ID: <008C2002145050698@vdtl-5300-7a.testlab-t37.com>
Mar 18 14:50:50.702: (C)S: Date: Mon, 18 Mar 2002 14:50:50 -0500
Mar 18 14:50:50.702: (C)S: Subject: Fax from On-Ramp GW vdlt-5300-7a[DNIS=8913144]
 [ANI=8915510]
Mar 18 14:50:50.702: (C)S: X-Mailer: IOS (tm) 5300 Software (C5300-IS-M)
Mar 18 14:50:50.702: (C)S: Disposition-Notification-To: admin@testlab-t37.com
Mar 18 14:50:50.702: (C)S: MIME-Version: 1.0
Mar 18 14:50:50.702: (C)S: Content-Type: multipart/fax-message;
Mar 18 14:50:50.702: (C)S: boundary="yradnuoB=_008B2002145048474.vdtl-5300-7atestlab-t37.com"
Mar 18 14:50:50.702: (C)S: From: "Fax " <FAX=8915510@vdtl-5300-7a.testlab-t37.com>
Mar 18 14:50:50.702: (C)S: X-Account-Id: 0
Mar 18 14:51:05.702: (C)S: --yradnuoB=_008B2002145048474.vdtl-5300-7atestlab-t37.com
Mar 18 14:51:05.702: (C)S: Content-ID: <008D2002145105702@vdtl-5300-7a.testlab-t37.com>
Mar 18 14:51:05.702: (C)S: Content-Type: image/tiff; application=faxbw
Mar 18 14:51:05.702: (C)S: Content-Transfer-Encoding: base64
Mar 18 14:51:05.706: esmtp_client_work: writing lingering data for socket 0
Mar 18 14:51:05.714: esmtp_client_work: writing lingering data for socket 0
Mar 18 14:51:14.726: esmtp_client_work: writing lingering data for socket 0
Mar 18 14:51:14.734: esmtp_client_work: writing lingering data for socket 0
Mar 18 14:51:14.738: (C)S: --yradnuoB=_008B2002145048474.vdtl-5300-7atestlab-t37.com--
Mar 18 14:51:14.738: esmtp_client_work: Sending terminating dot ...(socket=0)
Mar 18 14:51:14.738: (C)S: .  
!--- This is the terminating dot to end the SMTP session.

Mar 18 14:51:14.986: (C)R: 250 2.6.0 <008C2002145050698@vdtl-5300-7a.testlab-t37.com>
 Queued mail for delivery
Mar 18 14:51:14.986: (C)S: QUIT
Mar 18 14:51:15.406: (C)R: 221 2.0.0 testlab-smtp.testlab-t37.com Service closing
 transmission channel
Mar 18 14:51:15.406: esmtp_client_work: Freeing ctx=0x6266946C
Mar 18 14:51:15.406: esmtp_client: returned from work, context freed
Mar 18 14:51:18.938: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 38 seconds
vdtl-5300-7a#
vdtl-5300-7a# debug dmsp fax-to-doc 
Doc MSP fax to doc debugging is on
vdtl-5300-7a#
Mar 18 14:53:03.338: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 18 14:53:05.530: docmsp_call_setup_request: callid=227 
Mar 18 14:53:05.530: docmsp_call_setup_request(): ramp data dir=ONRAMP, conf dir=DEST
Mar 18 14:53:05.534: docmsp_caps_ind: call id=227, src=225
Mar 18 14:53:05.534: docmsp_bridge cfid=156, srccid=227, dstcid=225

Mar 18 14:53:05.534: docmsp_bridge(): ramp data dir=ONRAMP, conf dir=DEST, encode out=2
Mar 18 14:53:06.530: docmsp_bridge cfid=157, srccid=227, dstcid=226

Mar 18 14:53:06.530: docmsp_bridge(): ramp data dir=ONRAMP, conf dir=SRC, encode out=2
Mar 18 14:53:11.510: docmsp_xmit: call id src=225, dst=227
Mar 18 14:53:11.510: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:12.350: docmsp_xmit: call id src=225, dst=227

!--- Output suppressed.

Mar 18 14:53:22.242: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:22.242: docmsp_get_msp_event_buffer: 
Mar 18 14:53:23.082: docmsp_xmit: call id src=225, dst=227
Mar 18 14:53:23.082: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:23.922: docmsp_xmit: call id src=225, dst=227

!--- Output suppressed.

Mar 18 14:53:36.950: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:38.430: docmsp_xmit: call id src=225, dst=227
Mar 18 14:53:38.430: docmsp_process_rcv_data: call id src=225, dst=227 
Mar 18 14:53:38.434: docmsp_get_msp_event_buffer: 
Mar 18 14:53:41.022: docmsp_bdrop cfid=156, srccid=227, dstcid=225

Mar 18 14:53:41.022: docmsp_bdrop cfid=157, srccid=227, dstcid=226

Mar 18 14:53:41.026: docmsp_call_disconnect: callid=227 
Mar 18 14:53:41.026: docmsp_do_call_history: call id=227 
Mar 18 14:53:42.886: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 45 seconds
vdtl-5300-7a#

Remarque: Le mmoip de débogage envoient la commande d'adresse e-mail n'affiche rien à l'écran lui-même, mais il est très utile. Il utilise le routeur en tant que client de SMTP pour envoyer un email à l'adresse donnée dans la commande de débogage. L'email a le sujet défini dans la configuration et est « d'utilisateur de test de mspi ». Il contient une connexion des textes avec la ligne, « c'est un message électronique de test envoyé par l'intermédiaire de Cisco a actionné le livret Faxmail. »

Ceux-ci sont met au point pour le côté de télécopie de l'OnRamp :

vdtl-5300-7a# debug fmsp send t30
FMSP send t30 debugging is on
vdtl-5300-7a#
Mar 19 14:50:04.604: t30 call4Leg=311, state=1, substate=4
Mar 19 14:50:04.604: received flag of modulation:
0 
Mar 19 14:50:04.628: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 19 14:50:06.252: msg dump:FF C0 C2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 1E 86 62 
Mar 19 14:50:06.252: 
Mar 19 14:50:06.252: t30 call4Leg=311, state=1, substate=4
Mar 19 14:50:06.252: received: TSI remote id string: Fax 

Mar 19 14:50:06.672: msg dump:FF C8 C1 0 47 E 
Mar 19 14:50:06.672: 
Mar 19 14:50:06.824: t30 call4Leg=311, state=1, substate=4
Mar 19 14:50:06.824: in response receive WAIT FOR CD
Mar 19 14:50:11.632: t30 call4Leg=311, state=1, substate=6
Mar 19 14:50:11.632: received flag of modulation:
8 
Mar 19 14:50:19.304: t30 call4Leg=311, state=1, substate=6
Mar 19 14:50:19.304: received flag of modulation:
0 
Mar 19 14:50:20.364: msg dump:FF C8 F2 
Mar 19 14:50:20.364: 
Mar 19 14:50:22.324: t30 call4Leg=311, state=1, substate=6
Mar 19 14:50:22.324: received flag of modulation:
8 
Mar 19 14:50:31.643: t30 call4Leg=311, state=1, substate=6
Mar 19 14:50:31.643: received flag of modulation:
0 
Mar 19 14:50:32.683: msg dump:FF C8 F4 
Mar 19 14:50:32.683: 
Mar 19 14:50:33.155: t30 call4Leg=311, state=0, substate=6
Mar 19 14:50:33.155: fax session aborted by aplication
Mar 19 14:50:37.295: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 38 seconds
vdtl-5300-7a#
vdtl-5300-7a#debug fmsp receive t30 
FMSP receive t30 debugging is on
vdtl-5300-7a#
Mar 19 14:46:26.536: t30 call4Leg=307, state=1, substate=3  
!--- state=PHASE_B_RECEIVE  substate=TX_DIS_DTC_BLOCK

Mar 19 14:46:26.536: CSI_PACKET(8913180) 
!--- The CSI option, which shows that the called number is 8913180, is
!--- controlled by the fax receive called-subscriber configuration.

Mar 19 14:46:26.536: t30 call4Leg=307, state=1, substate=3
Mar 19 14:46:26.536: DIS_PACKET(speed: 5, resolution: 1, encoding:
1 
Mar 19 14:46:26.536: t30 call4Leg=307, state=1, substate=4   
!--- Moved to substate RX_DCS_DTC_BLOCK.

Mar 19 14:46:26.536: fax2_response_receive: PROCESSING
Mar 19 14:46:29.452: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:29.452: fax2_response_receive: PROCESSING
Mar 19 14:46:29.476: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 19 14:46:30.736: t30 call4Leg=307, state=1, substate=3
Mar 19 14:46:30.736: CSI_PACKET(8913180) 
Mar 19 14:46:30.736: t30 call4Leg=307, state=1, substate=3
Mar 19 14:46:30.736: DIS_PACKET(speed: 5, resolution: 1, encoding:
1   
!--- speed=14400, resolution=, encoding=modified read

Mar 19 14:46:30.736: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:30.736: fax2_response_receive: PROCESSING
Mar 19 14:46:31.100: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.100: fax2_response_receive: PROCESSING
Mar 19 14:46:31.100: msg dump:FF C0 C2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 1E 86 62 
Mar 19 14:46:31.100: 
Mar 19 14:46:31.100: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.100: received: TSI remote id string: Fax 

Mar 19 14:46:31.100: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.100: fax2_response_receive: PROCESSING
Mar 19 14:46:31.532: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.532: fax2_response_receive: PROCESSING
Mar 19 14:46:31.532: msg dump:FF C8 C1 0 47 E 
Mar 19 14:46:31.532: 
Mar 19 14:46:31.532: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.532: fax2_response_receive: PROCESSING
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=4
Mar 19 14:46:31.672: in response receive WAIT FOR CD
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=9   
!--- The substate is changed to RX_TCF.

Mar 19 14:46:31.672: received DCS_PACKET, BR: 9,  
!--- BR=v.21 14400

resolution: 1, encoding: 1, remote_id_string: Fax          
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=10  
!--- The substate is changed to WAIT_FOR_FDR.

Mar 19 14:46:31.672: wait for ready for data from
application
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=12   
!--- The substate is changed to TX_TCF_RESPONSE.

Mar 19 14:46:31.672: send CFR_PACKET
Mar 19 14:46:31.672: t30 call4Leg=307, state=1, substate=6   
!--- The substate is changed to CONFIGURE_RX_DATA.

Mar 19 14:46:31.672: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:36.472: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:36.472: fax2_configure_rx_data:
DETECTED_DATA
Mar 19 14:46:36.472: t30 call4Leg=307, state=2, substate=43  
!--- state = PHASE_C_RECEIVE, substate=RX_FIRST_DATA_BYTE - starting to RX page data...

Mar 19 14:46:36.472: No data yet
Mar 19 14:46:43.872: t30 call4Leg=307, state=2, substate=14  
!--- The substate is changed to RX_DATA.

Mar 19 14:46:43.872: end of page
Mar 19 14:46:43.872: t30 call4Leg=307, state=1, substate=6  
!--- The substate is changed to CONFIGURE_RX_DATA.

Mar 19 14:46:43.872: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:43.872: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:43.872: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:44.140: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:44.140: fax2_configure_rx_data:
DETECTED_COMMAND
Mar 19 14:46:44.140: t30 call4Leg=307, state=1, substate=7  
!--- The substate is changed to RX_COMMAND.

Mar 19 14:46:44.140: fax2_command_receive: NO_COMMAND, T2
timer not expired
Mar 19 14:46:45.200: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:45.200: fax2_command_receive: PROCESSING
Mar 19 14:46:45.200: msg dump:FF C8 F2 
Mar 19 14:46:45.200: 
Mar 19 14:46:45.200: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:45.200: fax2_command_receive: PROCESSING
Mar 19 14:46:45.352: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:45.352: fax2_command_receive:
RECEIVED_COMMAND
Mar 19 14:46:45.352: t30 call4Leg=307, state=3, substate=8    
!--- The substate is changed to ROUTE_COMMAND.

Mar 19 14:46:45.352: received MPS  
!--- Received Multipage Signal.

Mar 19 14:46:45.352: t30 call4Leg=307, state=3, substate=10  
!--- The substate is changed to WAIT_FOR_FDR.

Mar 19 14:46:45.352: waiting for page acceptence by the application
Mar 19 14:46:45.352: t30 call4Leg=307, state=3, substate=17  
!--- The substate is changed to SCHEDULE_PP_RESPONSE.

Mar 19 14:46:45.352: send MCF   
!--- Send a Message Confirmation.

Mar 19 14:46:45.352: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:45.352: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:47.172: t30 call4Leg=307, state=1, substate=6

!--- Now this must be done again, starting from the page data, because two pages
!--- are being sent.


Mar 19 14:46:47.172: fax2_configure_rx_data:
DETECTED_DATA
Mar 19 14:46:47.172: t30 call4Leg=307, state=2, substate=43
!--- state = PHASE_C_RECEIVE, substate=RX_FIRST_DATA_BYTE - starting to RX page data...

Mar 19 14:46:47.172: No data yet
Mar 19 14:46:56.212: t30 call4Leg=307, state=2, substate=14 
!--- The substate is changed to RX_DATA.

Mar 19 14:46:56.212: end of page
Mar 19 14:46:56.212: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:56.212: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:56.212: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:56.212: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:56.512: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:56.512: fax2_configure_rx_data:
DETECTED_COMMAND
Mar 19 14:46:56.512: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:56.512: fax2_command_receive: NO_COMMAND, T2
timer not expired
Mar 19 14:46:57.552: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:57.552: fax2_command_receive: PROCESSING
Mar 19 14:46:57.552: msg dump:FF C8 F4 
Mar 19 14:46:57.552: 
Mar 19 14:46:57.552: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:57.552: fax2_command_receive: PROCESSING
Mar 19 14:46:57.700: t30 call4Leg=307, state=1, substate=7
Mar 19 14:46:57.700: fax2_command_receive:
RECEIVED_COMMAND
Mar 19 14:46:57.700: t30 call4Leg=307, state=3, substate=8
Mar 19 14:46:57.700: received EOP   

!--- Received End of Procedure.

Mar 19 14:46:57.700: t30 call4Leg=307, state=3, substate=10
Mar 19 14:46:57.700: waiting for page acceptence by the application
Mar 19 14:46:57.700: t30 call4Leg=307, state=3, substate=17
Mar 19 14:46:57.700: send MCF       

!--- Send a Message Confirmation.

Mar 19 14:46:57.700: t30 call4Leg=307, state=1, substate=6
Mar 19 14:46:57.704: fax2_configure_rx_data: STILL_LOOKING,
T2 timer not expired
Mar 19 14:46:58.140: t30 call4Leg=307, state=0, substate=6  

!--- state=PHASE_IDLE

Mar 19 14:46:58.140: fax session aborted by aplication
Mar 19 14:47:02.188: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 38 seconds
vdtl-5300-7a#
vdtl-5300-7a# debug fax relay t30 called-number 8913144
Debugging fax relay t30 to 8913144
vdtl-5300-7a#
Mar 19 14:40:19.134: 0:D:302 1205778176 fr-entered (10ms)
Mar 19 14:40:22.498: 0:D:302 1205781540 fr-msg-tx CSI
Mar 19 14:40:23.826: 0:D:302 1205782870 fr-msg-tx DIS
Mar 19 14:40:25.070: %ISDN-6-CONNECT: Interface Serial0:18 is now connected to 8915510 
Mar 19 14:40:26.146: 0:D:302 1205785190 fr-msg-det TSI
Mar 19 14:40:27.026: 0:D:302 1205786070 fr-msg-det DCS
Mar 19 14:40:30.558: 0:D:302 1205789600 fr-msg-tx CFR
Mar 19 14:40:40.766: 0:D:302 1205799810 fr-msg-det MPS
Mar 19 14:40:41.266: 0:D:302 1205800310 fr-msg-tx MCF
Mar 19 14:40:53.098: 0:D:302 1205812140 fr-msg-det EOP
Mar 19 14:40:53.598: 0:D:302 1205812640 fr-msg-tx MCF
Mar 19 14:40:56.390: 0:D:302 1205815430 fr-msg-det DCN
Mar 19 14:40:57.682: %ISDN-6-DISCONNECT: Interface Serial0:18 disconnected from 8915510 ,
 call lasted 38 seconds
Mar 19 14:40:58.518: 0:D:302 1205817560 fr-end-dcn

fr-msg-tx indicates T.30 messages that are transmitted by the router
fr-msg-det indicates T.30 messages that are received by the router

Le pour en savoir plus, se rapportent au guide de dépannage de relais de télécopie.

Commandes show

vdtl-5300-7a# show call history fax brief 
<ID>: <start>hs.<index> +<connect> +<disc> pid:<peer_id> <direction> <addr>
dur hh:mm:ss tx:<packets>/<bytes> rx:<packets>/<bytes> <disc-cause>(<text>)
IP <ip>:<udp> rtt:<time>ms pl:<play>/<gap>ms lost:<lost>/<early>/<late>
delay:<last>/<min>/<max>ms <codec>
MODEMPASS <method> buf:<fills>/<drains> loss <overall%> <multipkt>/<corrected>
last <buf event time>s dur:<Min>/<Max>s
FR <protocol> [int dlci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>
<codec> (payload size)
ATM <protocol> [int vpi/vci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>
<codec> (payload size)
Telephony <int>: tx:<tot>/<voice>/<fax>ms <codec> noise:<lvl>dBm acom:<lvl>dBm
Proxy <ip>:<audio udp>,<video udp>,<tcp0>,<tcp1>,<tcp2>,<tcp3> endpt: <type>/<manf>
bw: <req>/<act> codec: <audio>/<video>
tx: <audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120 pkts>/<t120 bytes>
rx: <audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120 pkts>/<t120 bytes>


Telephony call-legs: 3
SIP call-legs: 0
H323 call-legs: 0
Total call-legs: 5
1225 : 374672hs.31 +2 +1367 pid:8913180 Answer 8915510
dur 00:00:13 tx:7/124 rx:104/693 10 :1F (normal call clearing (16):normal,
 unspecified (31): User abort)
Telephony 0:D:61: tx:0/0/0ms 14400 noise:0dBm acom:0dBm

122B : 401714hs.32 +100 +2966 pid:1 Originate andy@testlab-t37.com
dur 00:00:28 tx:50942/0 rx:0/0 10 :0 (normal call clearing (16):)
IP 172.18.106.36 AcceptedMime:0 DiscardedMime:0

1229 : 400917hs.33 +1 +4108 pid:8913180 Answer 8915510
dur 00:00:41 tx:11/164 rx:760/45251 10 :10 (normal call clearing (16):normal
 call clearing (16): Normal conn)
Telephony 0:D:64: tx:0/0/0ms 14400 noise:0dBm acom:0dBm

1230 : 439580hs.34 +100 +2971 pid:1 Originate andy@testlab-t37.com
dur 00:00:28 tx:50942/0 rx:0/0 10 :0 (normal call clearing (16):)
IP 172.18.106.36 AcceptedMime:0 DiscardedMime:0

122E : 438783hs.35 +1 +4109 pid:8913180 Answer 8915510
dur 00:00:41 tx:11/164 rx:761/45256 10 :10 (normal call clearing (16):normal
 call clearing (16): Normal conn)
Telephony 0:D:68: tx:0/0/0ms 14400 noise:0dBm acom:0dBm

Conversations connexes de la communauté de soutien de Cisco

Le site Cisco Support Community est un forum où vous pouvez poser des questions, répondre à des questions, faire part de suggestions et collaborer avec vos pairs.


Informations connexes


Document ID: 47763