Composition et accès : "Réseaux numériques à intégration de services (RNIS), canal de signalisation associé (CAS)"

Pontage de secours sur RNIS

17 décembre 2015 - Traduction automatique
Autres versions: PDFpdf | Anglais (22 août 2015) | Commentaires


Contenu


Introduction

Ce document explique et fournit un exemple de la façon configurer la sauvegarde jetant un pont sur avec le RNIS. Cette configuration emploie la méthode d'Interface de sauvegarde pour identifier que la liaison principale est en baisse. Pour plus d'informations sur la sauvegarde, voyez en configurant et dépannage de la sauvegarde DDR.

Dans les environnements WAN traversiers, la seule solution de sauvegarde de Routage à établissement de connexion à la demande (DDR) disponible est l'utilisation du RNIS, comme la transition au-dessus d'async n'est pas prise en charge.

Rendez-vous compte que la transition sur une connexion RNIS tend à maintenir la connexion active pendant très des longues périodes, sinon de manière permanente. Si l'opérateur téléphonique (compagnie de téléphone) facture le RNIS basé sur le temps de connexion et la liaison série qui est dépistée est en baisse pendant très un longtemps, ceci peut avoir comme conséquence une facture très grande.

Remarque: Cette configuration est pour un site et un canal B. Pour plus d'un canal B, vous devez utiliser des Profils de composeur. (Référez-vous aux Profils de composeur configurants pour jeter un pont sur utilisant la configuration RNIS.)

Pour les informations sur jeter un pont sur la configuration dans un environnement de non-sauvegarde, voyez la transition à travers le RNIS.

Conditions préalables

Conditions requises

Assurez-vous de répondre à ces exigences avant d'essayer cette configuration :

  • Possédez une connaissance de base du RNIS.

Composants utilisés

Les informations contenues dans ce document sont basées sur les versions de matériel et de logiciel suivantes :

  • Routeurs de la gamme Cisco 2500 avec une interface série WAN et une interface chacune BRI.

  • Version de logiciel 12.2(7b) de Cisco IOSÝ.

Remarque: Cette configuration peut être utilisée avec n'importe quel routeur qui a un lien (séquentiel) BLÊME et un port BRI.

Les informations contenues dans ce document ont été créées à partir des périphériques d'un environnement de laboratoire spécifique. Tous les périphériques utilisés dans ce document ont démarré avec une configuration effacée (par défaut). Si votre réseau est opérationnel, assurez-vous que vous comprenez l'effet potentiel de toute commande.

Produits connexes

Cette configuration peut être utilisée avec deux Routeurs quelconques qui exécutent le logiciel de Cisco IOS et chacun a au moins une interface série WAN et une interface BRI.

Conventions

Pour plus d'informations sur les conventions utilisées dans ce document, reportez-vous aux Conventions relatives aux conseils techniques Cisco.

Configurez

Cette section vous fournit des informations pour configurer les fonctionnalités décrites dans ce document.

Remarque: Pour obtenir des informations supplémentaires sur les commandes utilisées dans ce document, utilisez l'Outil de recherche de commande (clients enregistrés seulement).

Diagramme du réseau

Ce document utilise la configuration réseau suivante :

/image/gif/paws/10371/bridging.gif

Configurations

Ce document utilise les configurations suivantes :

Router1
!
hostname ROUTER1
!
!
username ROUTER2 password 0 same

!--- This is required for PPP Challenge Handshake Authentication Protocol
!--- (CHAP) authentication during dial backup.

!
!
isdn switch-type basic-5ess

!--- The ISDN switch type for this circuit. 
!--- Obtain this information from the Telco.
!--- This ISDN switch type is specific to the United States,
!--- and could change based on the requirements of the country and Telco.

!
interface Ethernet0
 ip address 172.16.55.33 255.255.255.240
 no ip directed-broadcast
 no ip mroute-cache
 bridge-group 1  

!--- Assign this interface to bridge-group 1.
!--- Frames are bridged only among interfaces in the same group.
!--- Note that the BRI interface and serial interface are also 
!--- in this bridge-group 1.

!
interface Serial0
 description Serial link to ROUTER2
 backup interface BRI0 

!--- This defines the backup interface. 
!--- Cisco IOS Software tracks the Serial0 interface, and
!--- uses BRI0 if Serial0 fails.

 ip address 172.16.54.1 255.255.255.0
 no ip directed-broadcast
 no ip mroute-cache
 no fair-queue
 bridge-group 1  

!--- Enable bridging on Serial0 for normal operation. 

!
interface BRI0
 description ISDN to ROUTER2
 ip address 172.16.53.19 255.255.255.240
 no ip directed-broadcast
 encapsulation ppp
 no ip mroute-cache
 dialer map bridge name ROUTER2 broadcast 5552000 

!--- The broadcast keyword is required to initiate the ISDN call.
!--- Dialer map bridge to the remote router. The statement includes
!--- the name of the remote router and the phone number to be dialed.
!--- Note that this dialer map statement includes the keyword bridge,
!--- and does not include the IP address of the peer, as required for
!--- IP routing-based dialer maps.

 dialer-group 1 

!--- Defines the interesting traffic as configured in the dialer-list.

 isdn switch-type basic-5ess 

!--- Check with your Telco for the correct values.

 ppp authentication chap
bridge-group 1 

!--- Enable bridging on BRI0.

!
dialer-list 1 protocol bridge permit 

!--- Defines the interesting traffic. In this case, all bridged traffic.

bridge 1 protocol ieee

!--- Defines the type of Spanning Tree Protocol (STP) used for the
!--- interface in bridge-group 1. Here, the IEEE STP is used.
!--- The IEEE 802.1D STP is the preferred way to run the bridge.

!

Router2
hostname router2
!
!
username ROUTER1 password 0 same 

!--- Required for PPP CHAP Authentication during dial backup.

!
isdn switch-type basic-5ess 

!--- Check with your Telco at the Router2 side for the correct values.   

!
interface Ethernet0
 ip address 172.16.55.2 255.255.255.240
 bridge-group 1 

!--- Enable bridging on Ethernet0.

!
interface Serial0
 description Serial link to ROUTER1 

!--- The backup interface bri0 command is not required on this side,
!--- because it is sufficient if one side tracks the serial interface.

 ip address 172.16.54.2 255.255.255.0 
 no fair-queue
 bridge-group 1 

!--- Enable bridging on Serial0 for normal operation.

interface BRI0
 description ISDN to ROUTER1
 ip address 172.16.53.17 255.255.255.240
 encapsulation ppp 
 no ip mroute-cache
 dialer map bridge name ROUTER1 broadcast 5551000 

!--- The broadcast keyword is required to initiate the ISDN call.

 dialer-group 1 

!--- Defines the interesting traffic as configured in the dialer-list.

 isdn switch-type basic-5ess 

!--- Check with your Telco at the Router2 side for the correct values.

 ppp authentication chap 
 bridge-group 1 

!--- Enable bridging on BRI0.

!
dialer-list 1 protocol bridge permit 

!--- Defines the interesting traffic. In this case, all bridged traffic.

bridge 1 protocol ieee

!--- Defines the type of STP used for the interface in 
!--- bridge-group 1. Here the IEEE STP is used. 
!--- The IEEE 802.1D STP is the preferred way to run the bridge.

!

Vérifiez

Cette section fournit des informations qui vous permettront de vérifier que votre configuration fonctionne correctement.

Certaines commandes show sont prises en charge par l'Output Interpreter Tool (clients enregistrés uniquement), qui vous permet de voir une analyse de la sortie de la commande show.

  • état de show isdn — affiche la couche 1 (L1), la couche 2 (L2), et pose 3 le statut (L3) des interfaces RNIS.

  • show dialer — affiche l'état du numéroteur et le statut individuel des canaux RNIS.

  • show bridge — classes d'affichages des entrées dans la base de données de pont transparent.

  • interface d'exposition — affiche le statut des diverses interfaces, telles que l'interface série et des interfaces BRI.

  • show spanning-tree — affiche la topologie de spanning tree connue du routeur.

commandes show sur ROUTER1 quand Serial0 est

ROUTER1# show isdn status
   Global ISDN Switchtype = basic-5ess
   ISDN BRI0 interface
   dsl 0, interface ISDN Switchtype = basic-5ess
   Layer 1 Status:
   DEACTIVATED
   Layer 2 Status:
   Layer 2 NOT Activated
   Layer 3 Status:
   0 Active Layer 3 Call(s)
   Activated dsl 0 CCBs = 0
   The Free Channel Mask: 0x80000003
   Number of L2 Discards = 36, L2D_Task Discards = 35
   Total Allocated ISDN CCBs = 0

ROUTER1# show dialer

BRI0 - dialer type = ISDN

Dial String Successes Failures Last DNIS Last status
   5552000 29 977 00:45:08 successful
   0 incoming call(s) have been screened.
   0 incoming call(s) rejected for callback.

BRI0:1 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is shutdown

BRI0:2 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is shutdown

ROUTER1# show bridge

Total of 300 station blocks, 298 free
   Codes: P - permanent, S - self

Bridge Group 1:

 Address Action Interface Age RX count TX count
   0000.0c76.2882 forward Serial0 0 5 4

!--- Bridging traffic goes through Serial0.

   00d0.58ad.ae13 forward Ethernet0 0 42 5

commandes show sur ROUTER1 quand Serial0 est vers le bas

ROUTER1# show isdn status
   Global ISDN Switchtype = basic-5ess
   ISDN BRI0 interface
   dsl 0, interface ISDN Switchtype = basic-5ess
   Layer 1 Status:
   ACTIVE
   Layer 2 Status:
   TEI = 114, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

   !--- ISDN L1 and L2 will be up (when Serial0 fails)
   !--- even if interesting traffic is not present.

   Layer 3 Status:
   1 Active Layer 3 Call(s)
   Activated dsl 0 CCBs = 1
   CCB:callid=8484, sapi=0, ces=1, B-chan=1, calltype=DATA
   The Free Channel Mask: 0x80000002
   Total Allocated ISDN CCBs = 1

ROUTER1# show dialer

BRI0 - dialer type = ISDN

Dial String Successes Failures Last DNIS Last status
   5552000 30 977 00:00:16 successful
   0 incoming call(s) have been screened.
   0 incoming call(s) rejected for callback.

BRI0:1 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up
   Dial reason: bridge (0xFFFF)
   Time until disconnect 106 secs
   Connected to 5552000 (ROUTER2)

BRI0:2 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is idle
   
ROUTER1# show bridge

Total of 300 station blocks, 298 free
   Codes: P - permanent, S - self

Bridge Group 1:

 Address Action Interface Age RX count TX count
   0000.0c76.2882 forward BRI0 0 5 4	

!--- Bridging traffic now goes through BRI0.

   00d0.58ad.ae13 forward Ethernet0 0 5 5

Dépannez

Cette section fournit des informations que vous pouvez utiliser pour dépanner votre configuration.

Dépannage des ressources

Utilisez ces ressources au besoin :

Dépannage des commandes

Certaines commandes show sont prises en charge par l'Output Interpreter Tool (clients enregistrés uniquement), qui vous permet de voir une analyse de la sortie de la commande show.

Remarque: Avant d'émettre des commandes debug, reportez-vous aux Informations importantes sur les commandes de débogage.

  • mettez au point le numéroteur — fournit des informations au sujet des événements d'interface de numérotation.

  • debug isdn event — messages de débogage d'affichages liés à l'activité RNIS qui se produit du côté utilisateur de l'interface RNIS.

  • debug isdn q931 — fournit des informations au sujet de l'établissement d'appel et du démontage de la connexion réseau RNIS (L3) entre le routeur local (côté utilisateur) et le réseau.

  • debug isdn q921 — messages de débogage d'affichages liés aux procédures d'accès de la couche liaison de données (L2) qui ont lieu au routeur sur le canal D (LAPD) de son interface RNIS.

  • debug ppp negotiation — messages de débogage d'affichages liés à la négociation des paramètres d'options PPP et de protocole de contrôle de réseau (NCP).

  • debug ppp authentication — Les messages de débogage d'affichages ont associé à l'échange des paquets de CHAP et de Password Authentication Protocol (PAP).

la sortie de débogage sur ROUTER1 quand Serial0 descend et RNIS reprend

ROUTER1# show debug
   Dial on demand:
   Dial on demand events debugging is on
   PPP:
   PPP authentication debugging is on
   PPP protocol negotiation debugging is on
   ISDN:
   ISDN events debugging is on
   ISDN Q921 packets debugging is on
   ISDN Q931 packets debugging is on

ROUTER1#

!--- Interface serial0 goes down.

ROUTER1#
00:56:53: %LINK-3-UPDOWN: Interface Serial0, changed state to down
*Mar  1 00:56:53.103: ISDN BR0 EVENT: isdn_sw_cstate: State = 0,
 Old State = 6
00:56:53: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
*Mar  1 00:56:53.107: BR0:1 LCP: State is Closed
*Mar  1 00:56:53.111: BR0:1 DDR: disconnecting call
00:56:53: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
*Mar  1 00:56:53.119: BR0:2 LCP: State is Closed
*Mar  1 00:56:53.119: BR0:2 DDR: disconnecting call
*Mar  1 00:56:53.127: ISDN BR0 EVENT: isdn_sw_cstate: State = 4,
 Old State = 6
*Mar  1 00:56:53.135: ISDN BR0 EVENT: isdn_sw_cstate: State = 4,
 Old State = 6
*Mar  1 00:56:53.567: ISDN BR0: RX <- IDCKRQ ri=0 ai=127
*Mar  1 00:56:53.567: ISDN Recvd L1 prim 3 dsl 0 state 3 ctrl_state 0
*Mar  1 00:56:53.571: ISDN BR0: L1 persistent Deactivated
*Mar  1 00:56:53.571: ISDN Recvd L1 prim 7 dsl 0 state 3 ctrl_state 0
*Mar  1 00:56:53.575: ISDN BR0: Recvd MPH_IIC_IND from L1
*Mar  1 00:56:53.575: ISDN Recvd L1 prim 7 dsl 0 state 3 ctrl_state 0
*Mar  1 00:56:53.579: ISDN BR0: Recvd MPH_IIC_IND from L1
*Mar  1 00:56:53.579: ISDN Recvd L1 prim 1 dsl 0 state 3 ctrl_state 0
*Mar  1 00:56:53.583: ISDN BR0: L1 is IF_ACTIVE
*Mar  1 00:56:53.583: ISDN BR0 EVENT: isdn_sw_cstate: State = 4,
 Old State = 6
*Mar  1 00:56:53.587: ISDN BR0: L2-TERM: ces/tei=1/0
 AWAIT_ESTABLISH->TERM_DOWN
*Mar  1 00:56:53.591: ISDN BR0: Incoming call id = 0x0010, dsl 0
*Mar  1 00:56:53.595: ISDN BR0: L2-TERM: ces/tei=1/0
 TERM_DOWN->AWAIT_ESTABLISH
00:56:53: %LINK-3-UPDOWN: Interface BRI0, changed state to up
*Mar  1 00:56:53.631: ISDN BR0 EVENT: isdn_sw_cstate: State = 4,
 Old State = 6
*Mar  1 00:56:53.655: ISDN BR0: TX -> IDREQ ri=48769 ai=127
00:56:54: %LINEPROTO-5-UPDOWN: 
Line protocol on Interface Serial0, changed state to down
*Mar  1 00:56:54.387: ISDN BR0: RX <- IDCKRQ ri=0 ai=127
*Mar  1 00:56:55.655: ISDN BR0: TX -> IDREQ ri=42642 ai=127
*Mar  1 00:56:55.699: ISDN BR0: RX <- IDASSN ri=42642 ai=68
*Mar  1 00:56:55.791: ISDN BR0: TX -> SABMEp c/r=0 sapi=0 tei=68
*Mar  1 00:56:55.823: ISDN BR0: RX <- UAf c/r=0 sapi=0 tei=68
00:56:55: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0,
TEI 68 changed to up
*Mar  1 00:56:55.831: ISDN BR0: L2-TERM: ces/tei=1/68 
AWAIT_ESTABLISH->ESTABLISHED

!--- Interesting traffic has not arrived yet from Host1, 
!--- but ISDN L1 and L2 are up now.

ROUTER1# show isdn stat
Global ISDN Switchtype = basic-5ess
ISDN BRI0 interface
        dsl 0, interface ISDN Switchtype = basic-5ess
    Layer 1 Status:
        ACTIVE
    Layer 2 Status:
        TEI = 68, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
        I_Queue_Len 0, UI_Queue_Len 0
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask:  0x80000003
    Number of L2 Discards = 0, L2 Session ID = 34
    Total Allocated ISDN CCBs = 0
ROUTER1#
*Mar  1 00:57:25.839: ISDN BR0: TX -> RRp sapi=0 tei=68 nr=0
*Mar  1 00:57:25.871: ISDN BR0: RX <- RRf sapi=0 tei=68 nr=0
ROUTER1#


!--- Interesting traffic arrives now, 
!--- which triggers ISDN Dialup (see below).

*Mar  1 00:57:32.519: BR0 DDR: Dialing cause bridge (0xFFFF)
*Mar  1 00:57:32.519: BR0 DDR: Attempting to dial 5552000
*Mar  1 00:57:32.523: ISDN BR0: Outgoing call id = 0x800E, dsl 0
*Mar  1 00:57:32.527: ISDN BR0: Event: Call to 5552000 at 64 Kb/s
*Mar  1 00:57:32.527: ISDN BR0: process_bri_call(): call id 0x800E, 
called_number 5552000, speed 64, call type DATA
*Mar  1 00:57:32.531: CCBRI_Go Fr Host InPkgInfo (Len=22) :
*Mar  1 00:57:32.535: 1 0 1 80 E 0 4 2 88 90 18 
1 83 2C 7 35 35 35 32 30 30 30
*Mar  1 00:57:32.543:
*Mar  1 00:57:32.547: CC_CHAN_GetIdleChanbri: dsl 0
*Mar  1 00:57:32.547:     Found idle channel B1
*Mar  1 00:57:32.563: ISDN BR0: TX -> INFOc sapi=0 tei=68 ns=0 nr=0 
i=0x08010E05040288901801832C0735353532303030
*Mar  1 00:57:32.583:     SETUP pd = 8  callref = 0x0E
*Mar  1 00:57:32.591:         Bearer Capability i = 0x8890
*Mar  1 00:57:32.599:         Channel ID i = 0x83
*Mar  1 00:57:32.603:         Keypad Facility i = '5552000'
*Mar  1 00:57:32.867: ISDN BR0: RX <- INFOc sapi=0 tei=68 ns=0 nr=1 
i=0x08018E02180189
*Mar  1 00:57:32.875:     CALL_PROC pd = 8  callref = 0x8E
*Mar  1 00:57:32.883:         Channel ID i = 0x89
*Mar  1 00:57:32.899: ISDN BR0: TX -> RRr sapi=0 tei=68 nr=1
*Mar  1 00:57:32.907: CCBRI_Go Fr L3 pkt (Len=7) :
*Mar  1 00:57:32.907: 2 1 E 98 18 1 89
*Mar  1 00:57:32.911:
*Mar  1 00:57:32.915: ISDN BR0: LIF_EVENT: ces/callid 1/0x800E
 HOST_PROCEEDING
*Mar  1 00:57:32.919: ISDN BR0: HOST_PROCEEDING
*Mar  1 00:57:32.919: ISDN BR0: HOST_MORE_INFO
*Mar  1 00:57:33.159: ISDN BR0: RX <- INFOc sapi=0 tei=68 ns=1
 nr=1 i=0x08018E07
*Mar  1 00:57:33.167:     CONNECT pd = 8  callref = 0x8E
*Mar  1 00:57:33.183: ISDN BR0: TX -> RRr sapi=0 tei=68 nr=2
*Mar  1 00:57:33.191: CCBRI_Go Fr L3 pkt (Len=4) :
*Mar  1 00:57:33.191: 7 1 E 91
*Mar  1 00:57:33.195:
*Mar  1 00:57:33.199: ISDN BR0: LIF_EVENT: ces/callid 1/0x800E
 HOST_CONNECT
00:57:33: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
*Mar  1 00:57:33.215: ISDN: get_isdn_service_state(): 
idb 0x19F4D8 bchan 2 is_isdn 1 Not a Pri
*Mar  1 00:57:33.215: BR0:1 PPP: Treating connection as a callout
*Mar  1 00:57:33.219: BR0:1 PPP: Phase is ESTABLISHING,
 Active Open [0 sess, 1 load]
*Mar  1 00:57:33.223: BR0:1 LCP: O CONFREQ [Closed] id 27 len 15
*Mar  1 00:57:33.227: BR0:1 LCP:    AuthProto CHAP
 (0x0305C22305)
*Mar  1 00:57:33.231: BR0:1 LCP:    MagicNumber 0x6091A5F6
 (0x05066091A5F6)
*Mar  1 00:57:33.235: ISDN BR0: Event: Connected to 5552000
 on B1 at 64 Kb/s
*Mar  1 00:57:33.247: ISDN BR0: TX -> INFOc sapi=0 tei=68 ns=1 nr=2
 i=0x08010E0F
*Mar  1 00:57:33.251:     CONNECT_ACK pd = 8  callref = 0x0E
*Mar  1 00:57:33.267: BR0:1 LCP: I CONFREQ [REQsent] id 4 len 15
*Mar  1 00:57:33.271: BR0:1 LCP:    AuthProto CHAP
 (0x0305C22305)
*Mar  1 00:57:33.275: BR0:1 LCP:    MagicNumber 0x6062D6EA
 (0x05066062D6EA)
*Mar  1 00:57:33.279: BR0:1 LCP: O CONFACK [REQsent] id 4 len 15
*Mar  1 00:57:33.283: BR0:1 LCP:    AuthProto CHAP
 (0x0305C22305)
*Mar  1 00:57:33.287: BR0:1 LCP:    MagicNumber 0x6062D6EA
 (0x05066062D6EA)
*Mar  1 00:57:33.291: BR0:1 LCP: I CONFACK [ACKsent] id 27 len 15
*Mar  1 00:57:33.291: BR0:1 LCP:    AuthProto CHAP
 (0x0305C22305)
*Mar  1 00:57:33.295: BR0:1 LCP:    MagicNumber 0x6091A5F6
 (0x05066091A5F6)
*Mar  1 00:57:33.299: BR0:1 LCP: State is Open
*Mar  1 00:57:33.303: BR0:1 PPP: Phase is AUTHENTICATING,
 by both [0 sess, 1 load]
*Mar  1 00:57:33.307: BR0:1 CHAP: O CHALLENGE id 14
 len 28 from "ROUTER1"
*Mar  1 00:57:33.319: BR0:1 CHAP: I CHALLENGE id 4
 len 28 from "ROUTER2"
*Mar  1 00:57:33.327: BR0:1 CHAP: O RESPONSE id 4
 len 28 from "ROUTER1"
*Mar  1 00:57:33.335: ISDN BR0: RX <- RRr sapi=0
 tei=68 nr=2
*Mar  1 00:57:33.351: BR0:1 CHAP: I SUCCESS id 4
 len 4
*Mar  1 00:57:33.367: BR0:1 CHAP: I RESPONSE id 14
 len 28 from "ROUTER2"
*Mar  1 00:57:33.371: BR0:1 CHAP: O SUCCESS id 14
 len 4
*Mar  1 00:57:33.375: BR0:1 PPP: Phase is UP [0 sess, 0 load]
*Mar  1 00:57:33.379: BR0:1 BNCP: O CONFREQ [Closed] id 14
 len 4
*Mar  1 00:57:33.387: BR0:1 CDPCP: O CONFREQ [Closed] id 14
 len 4
*Mar  1 00:57:33.395: BR0:1 BNCP: I CONFREQ [REQsent] id 4
 len 4
*Mar  1 00:57:33.399: BR0:1 BNCP: O CONFACK [REQsent] id 4
 len 4
*Mar  1 00:57:33.403: BR0:1 IPCP: I CONFREQ [Not negotiated] id 4
 len 10
*Mar  1 00:57:33.407: BR0:1 IPCP:    Address 172.16.53.17
 (0x0306AC103511)
*Mar  1 00:57:33.415: BR0:1 LCP: O PROTREJ [Open] id 28
 len 16 protocol IPCP 
(0x80210104000A0306AC103511)
*Mar  1 00:57:33.419: BR0:1 CDPCP: I CONFREQ [REQsent] id 4
 len 4
*Mar  1 00:57:33.423: BR0:1 CDPCP: O CONFACK [REQsent] id 4
 len 4
*Mar  1 00:57:33.427: BR0:1 BNCP: I CONFACK [ACKsent] id 14
 len 4
*Mar  1 00:57:33.431: BR0:1 BNCP: State is Open
*Mar  1 00:57:33.435: BR0:1 CDPCP: I CONFACK [ACKsent] id 14
 len 4
*Mar  1 00:57:33.439: BR0:1 CDPCP: State is Open
*Mar  1 00:57:33.443: BR0:1 DDR: dialer protocol up
00:57:34: %LINEPROTO-5-UPDOWN: 
Line protocol on Interface BRI0:1, changed state to up
00:57:39: %ISDN-6-CONNECT: Interface BRI0:1 is now connected
 to 5552000 ROUTER2
ROUTER1#

ROUTER1# show isdn status
Global ISDN Switchtype = basic-5ess
ISDN BRI0 interface
        dsl 0, interface ISDN Switchtype = basic-5ess
    Layer 1 Status:
        ACTIVE
    Layer 2 Status:
        TEI = 68, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
        I_Queue_Len 0, UI_Queue_Len 0
    Layer 3 Status:
        1 Active Layer 3 Call(s)
        CCB:callid=800E, sapi=0, ces=1, B-chan=1, calltype=DATA
    Active dsl 0 CCBs = 1
    The Free Channel Mask:  0x80000002
    Number of L2 Discards = 0, L2 Session ID = 34
    Total Allocated ISDN CCBs = 1
*Mar  1 00:58:03.343: ISDN BR0: TX -> RRp sapi=0 tei=68 nr=2
*Mar  1 00:58:03.379: ISDN BR0: RX <- RRf sapi=0 tei=68 nr=2pann
ROUTER1# show spanning-tree

 Bridge group 1 is executing the ieee compatible Spanning Tree protocol
   Bridge Identifier has priority 32768, address 0060.5cf4.a9a8
   Configured hello time 2, max age 20, forward delay 15
   Current root has priority 32768, address 0060.5cf4.a955
   Root port is 3 (BRI0), cost of root path is 15625
   Topology change flag set, detected flag not set
   Number of topology changes 10 last change occurred 00:01:15 ago
   from Serial0
   Times: hold 1, topology change 35, notification 2
   hello 2, max age 20, forward delay 15
   Timers: hello 0, topology change 0, notification 0, aging 15

 Port 2 (Ethernet0) of Bridge group 1 is forwarding
   Port path cost 100, Port priority 128, Port Identifier 128.2.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.2, designated path cost 15625
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   BPDU: sent 751, received 0

 Port 3 (BRI0) of Bridge group 1 is forwarding    

!---  BRI Interface forwards the bridged traffic now.

   Port path cost 15625, Port priority 128, Port Identifier 128.3.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a955
   Designated port id is 128.3, designated path cost 0
   Timers: message age 2, forward delay 0, hold 0
   Number of transitions to forwarding state: 3
   BPDU: sent 1014, received 608

 Port 6 (Serial0) of Bridge group 1 is down
   Port path cost 647, Port priority 128, Port Identifier 128.6.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.6, designated path cost 15625
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 1
   BPDU: sent 15, received 27

ROUTER1#
   *Mar 1 00:58:33.387: ISDN BR0: TX -> RRp sapi=0 tei=68 nr=2
   *Mar 1 00:58:33.423: ISDN BR0: RX <- RRf sapi=0 tei=68 nr=2

la sortie de débogage sur ROUTER1 quand Serial0 revient de nouveau et RNIS relâche l'appel

00:58:37: %LINK-3-UPDOWN: Interface Serial0, changed state to up
   *Mar 1 00:58:37.671: BR0:1 DDR: disconnecting call
   *Mar 1 00:58:37.675: BR0:2 DDR: disconnecting call
   *Mar 1 00:58:37.675: ISDN BR0: Event: Hangup call to call id 0x800E
   *Mar 1 00:58:37.679: ISDN BR0: process_disconnect(): call id 0x800E,
    call type is DATA, b_idb 0x19F4D8, ces 1, cause Normal call
   clearing(0x10)
   00:58:37: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from
   5552000 ROUTER2, call lasted 64 seconds
   *Mar 1 00:58:37.691: ISDN: get_isdn_service_state(): idb 0x19F4D8
    bchan 2 is_isdn 1 Not a Pri
   *Mar 1 00:58:37.695: CCBRI_Go Fr Host InPkgInfo (Len=13) :
   *Mar 1 00:58:37.699: 5 0 1 80 E 3 8 1 90 8 2 80 90
   *Mar 1 00:58:37.703:
   *Mar 1 00:58:37.719: ISDN BR0: TX -> INFOc sapi=0 tei=68 ns=2 nr=2 
    i=0x08010E4508028090
   *Mar 1 00:58:37.727: DISCONNECT pd = 8 callref = 0x0E
   *Mar 1 00:58:37.735: Cause i = 0x8090 - Normal call clearing
   *Mar 1 00:58:37.743: ISDN BR0 EVENT: isdn_sw_cs!!!!!!!!!!!!!!!!!!!tate:
    State = 6, Old State = 4
   00:58:37: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
   *Mar 1 00:58:37.751: BR0:1 BNCP: State is Closed
   *Mar 1 00:58:37.755: BR0:1 CDPCP: State is Closed
   *Mar 1 00:58:37.755: BR0:1 PPP: Phase is TERMINATING [0 sess, 1 load]
   *Mar 1 00:58:37.759: BR0:1 LCP: State is Closed
   *Mar 1 00:58:37.763: BR0:1 PPP: Phase is DOWN [0 sess, 1 load]
   *Mar 1 00:58:37.763: BR0:1 DDR: disconnecting call
   *Mar 1 00:58:37.775: ISDN Recvd L1 prim 3 dsl 0 state 1 ctrl_state 0
   *Mar 1 00:58:37.779: ISDN BR0: Physical layer is IF_DOWN
   *Mar 1 00:58:37.783: ISDN BR0: Shutting down ME
   00:58:37: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0,
    TEI 68 changed to down
   *Mar 1 00:58:37.791: ISDN BR0: L2-TERM: ces/tei=1/68
    ESTABLISHED->TERM_DOWN
   *Mar 1 00:58:37.795: ISDN BR0: LIF_EVENT: ces/callid 1/0x800E
    HOST_DISCONNECT_ACK
   *Mar 1 00:58:37.803: ISDN: get_isdn_service_state(): idb 0x19F4D8
    bchan 2 is_isdn 1 Not a Pri
   *Mar 1 00:58:37.807: ISDN BR0: HOST_DISCONNECT_ACK: call type is DATA
   00:58:37: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
   *Mar 1 00:58:37.815: BR0:1 LCP: State is Closed
   *Mar 1 00:58:37.815: BR0:1 DDR: disconnecting call
   *Mar 1 00:58:37.819: ISDN BR0: Shutting down ISDN Layer 3
   00:58:37: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0,
    TEI 68 changed to down
   00:58:37: %LINK-5-CHANGED: Interface BRI0, changed state to standby mode
   *Mar 1 00:58:37.847: ISDN BR0 EVENT: isdn_sw_cstate: State = 6,
   Old State = 4
   00:58:37: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
   *Mar 1 00:58:37.855: BR0:2 LCP: State is Closed
   *Mar 1 00:58:37.855: BR0:2 DDR: disconnecting call
   *Mar 1 00:58:37.895: ISDN BR0: Incoming call id = 0x0011, dsl 0
   *Mar 1 00:58:37.895: ISDN BR0: L2-TERM: ces/tei=1/0
    TERM_DOWN->AWAIT_ESTABLISH
   *Mar 1 00:58:37.935: ISDN BR0: Activating
   00:58:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
   changed state to up
   00:58:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1,
   changed state to down
   *Mar 1 00:58:39.939: ISDN BR0: Could not bring up interface
   *Mar 1 00:58:39.943: ISDN BR0: Shutting down ISDN Layer 3
   *Mar 1 00:58:39.963: ISDN BR0: Activating
   *Mar 1 00:58:41.943: ISDN BR0: Could not bring up interface
   *Mar 1 00:58:41.947: ISDN BR0: Shutting down ISDN Layer 3
   *Mar 1 00:58:41.947: ISDN BR0: Activating
   ROUTER1#
   
   ROUTER1# show isdn status
   Global ISDN Switchtype = basic-5ess
   ISDN BRI0 interface
   dsl 0, interface ISDN Switchtype = basic-5ess
   Layer 1 Status:
   DEACTIVATED
   Layer 2 Status:
   Layer 2 NOT Activated         

!--- ISDN L1 and L2 are back to the deactivated state.

   Layer 3 Status:
   0 Active Layer 3 Call(s)
   Active dsl 0 CCBs = 0
   The Free Channel Mask: 0x80000003
   Number of L2 Discards = 0, L2 Session ID = 39
   Total Allocated ISDN CCBs = 0
   ROUTER1#
   *Mar 1 00:58:49.951: ISDN BR0: Could not bring up interface
   *Mar 1 00:58:49.951: ISDN BR0: Shutting down ISDN Layer 3
   ROUTER1#

ROUTER1# show spanning-tree

 Bridge group 1 is executing the ieee compatible Spanning Tree protocol
   Bridge Identifier has priority 32768, address 0060.5cf4.a9a8
   Configured hello time 2, max age 20, forward delay 15
   Current root has priority 32768, address 0060.5cf4.a955
   Root port is 6 (Serial0), cost of root path is 647
   Topology change flag not set, detected flag not set
   Number of topology changes 13 last change occurred 00:28:23 ago
   from Serial0
   Times: hold 1, topology change 35, notification 2
   hello 2, max age 20, forward delay 15
   Timers: hello 0, topology change 0, notification 0, aging 300

 Port 2 (Ethernet0) of Bridge group 1 is forwarding
   Port path cost 100, Port priority 128, Port Identifier 128.2.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.2, designated path cost 647
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   BPDU: sent 1633, received 0

 Port 3 (BRI0) of Bridge group 1 is down

!--- BRI0 is in the down state when Serial 0 is up.

   Port path cost 15625, Port priority 128, Port Identifier 128.3.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.3, designated path cost 647
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 3
   BPDU: sent 1014, received 622

 Port 6 (Serial0) of Bridge group 1 is forwarding 

!--- Serial0 forwards the bridged traffic now.

   Port path cost 647, Port priority 128, Port Identifier 128.6.
   Designated root has priority 32768, address 0060.5cf4.a955
   Designated bridge has priority 32768, address 0060.5cf4.a955
   Designated port id is 128.6, designated path cost 0
   Timers: message age 1, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   BPDU: sent 18, received 896
ROUTER1#

Conversations connexes de la communauté de soutien de Cisco

Le site Cisco Support Community est un forum où vous pouvez poser des questions, répondre à des questions, faire part de suggestions et collaborer avec vos pairs.


Informations connexes


Document ID: 10371