WAN : Protocole point à point (PPP)

Délais d'inactivité par utilisateur PPP

17 décembre 2015 - Traduction automatique
Autres versions: PDFpdf | Anglais (22 août 2015) | Commentaires


Contenu


Introduction

Ce conseil technique explique comment implémenter des délais d'attente de par-utilisateur sur des serveurs d'accès Cisco. Pour que les délais d'attente de par-utilisateur fonctionnent correctement, vous devez exécuter la version 11.3(8)T ou ultérieures de Cisco IOS. Si vous exécutez une version antérieure de Cisco IOS, les temporisateurs pourraient seulement fonctionner en certaines configurations de base, telles qu'async seulement sans des Profils virtuels.

Ce document couvre la configuration du serveur d'accès à distance (NAS) et du serveur d'Authentification, autorisation et comptabilité (AAA). Il également fournit l'exposition et met au point la sortie de commande ainsi vous pouvez confirmer si vos périphériques fonctionnent correctement, et ainsi vous pouvez mettre au point tous les problèmes.

Conditions préalables

Conditions requises

Aucune spécification déterminée n'est requise pour ce document.

Composants utilisés

Les informations contenues dans ce document sont basées sur les versions de matériel et de logiciel suivantes :

  • Version 11.3(8)T ou ultérieures de Cisco IOS

Les informations contenues dans ce document ont été créées à partir des périphériques d'un environnement de laboratoire spécifique. Tous les périphériques utilisés dans ce document ont démarré avec une configuration effacée (par défaut). Si votre réseau est opérationnel, assurez-vous que vous comprenez l'effet potentiel de toute commande.

Conventions

Pour plus d'informations sur les conventions utilisées dans ce document, reportez-vous aux Conventions relatives aux conseils techniques Cisco.

Détails techniques

Avant de discuter les délais d'attente de par-utilisateur, qui apportent d'autres variables comme la configuration d'AAA et les serveurs RADIUS/TACACS+, nous examinerons comment configurer un serveur d'accès pour des réparer-délais d'attente, qui est des délais d'attente que sont appliqués sur une base globale et sont appliqués à chacun qui se connecte.

Les commandes Cisco IOS principales sont dialer idle-timeout et timeout absolute. Chacun de ceux là sont des commandes de configuration d'interface. Nous discuterons également une troisième commande, le ppp timeout idle, qui est utilisé sur des interfaces de vaccess.

<x> de dialer idle-timeout

Cette commande peut être configurée sur tous les interface et contrôles numéroteur-capables combien de temps la connexion peut être de veille (en quelques secondes) avant qu'elle soit terminée. Répertoriés ci-dessous sont quatre vous dirige devraient noter au sujet de cette commande :

  1. Cette commande peut seulement être appliquée aux interfaces qui sont numéroteur-capables. Par défaut que toutes les interfaces RNIS (BRI et PRI) soyez numéroteur-capable, ainsi ajoutant cette commande n'est pas un problème. Les interfaces asynchrones (interfaces asynchrones du groupe y compris) ne sont pas numéroteur-capables par défaut, vous doivent les faire ainsi en présentant l'intrabande de commande dialer. Seulement après écrire l'ordre de dialer in-band sur l'interface asynchrone pouvez vous configurer le dialer idle-timeout. Note

    Remarque: Le vtemplate (et donc les interfaces de vaccess) ne sont pas numéroteur-capables (ils sont point par point seulement) et ne peuvent pas utiliser ainsi cette commande.

  2. Sur une interface numéroteur-capable (c'est-à-dire, le RNIS ou async avec le dialer in-band), le par défaut est le dialer idle-timeout 120 (secondes). C'est généralement trop court dans un environnement ISP, ainsi vous devriez presque toujours augmenter ceci.

  3. Le dialer idle-timeout par défaut est seulement remis à l'état initial sur le trafic sortant (le trafic vers l'utilisateur) qui apparie le dialer-list (c'est-à-dire, il est considéré intéressant). Il est possible de le remettre à l'état initial pour le trafic intéressant d'arrivée aussi bien en ajoutant l'un ou l'autre de mot clé à la fin de la commande (c'est-à-dire, dialer idle-timeout 600 l'un ou l'autre).

  4. Le trafic considéré « intéressant » est défini par la commande de <n> de dialer-list, où le <n> apparie le nombre dans votre appel de procédure de <n> de dialer-group.

<y> de <x> de timeout absolute

Cette commande peut être configurée sur n'importe quelle interface WAN, y compris des interfaces asynchrones, des interfaces RNIS, des interfaces de numérotation, et des interfaces de vtemplate. Il contrôle combien de temps la connexion peut être en hausse avant qu'elle soit terminée. Notez que la syntaxe est <y> de <x> où le <x> a lieu en quelques minutes et le <y> a lieu en quelques secondes.

<x> de ppp timeout idle

Cette commande peut seulement être configurée sur des interfaces de vtemplate (et est même masqué dans le programme d'analyse syntaxique), et des contrôles combien de temps la connexion peut être de veille (en quelques secondes) avant qu'elle soit terminée. Sa fonction est très semblable à celle de la commande de dialer idle-timeout sur des interfaces de numérotation, seulement le ppp timeout idle est pour des interfaces vtemplate/vaccess. Puisqu'il est utilisé spécifiquement sur des interfaces vtemplate/vaccess, cette commande est appropriée pour des configurations de virtuel-profil (où une interface de vaccess est toujours créée pour un utilisateur), et des passerelles domestiques de Réseau privé virtuel à accès commuté (VPDN) (où les interfaces projetées est toujours terminées sur une interface de vaccess). À la différence de la commande de dialer idle-timeout, il n'y a aucun concept du trafic intéressant, et tout le trafic d'utilisateur remettra à l'état initial ainsi le temporisateur de veille. Les paquets du trafic de non-utilisateur tel que le Keepalives du Link Control Protocol (LCP) et de négociation de protocole de contrôle de réseau (NCP) ne remettent pas à l'état initial le temporisateur.

Configurez

Cette section vous fournit des informations pour configurer les fonctionnalités décrites dans ce document.

Remarque: Pour obtenir des informations supplémentaires sur les commandes utilisées dans ce document, utilisez l'Outil de recherche de commande (clients enregistrés seulement).

Ce document utilise les configurations suivantes :

Configuration de base (Profils virtuels non activés)

Pour apprendre des buts, nous assumerons une configuration de base telle que celle ci-dessous. La caractéristique de Profils virtuels n'est pas activée.

Configuration de base
!
version 11.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname access-3
!
aaa new-model
aaa authentication login default tacacs+ local
aaa authentication login console none
aaa authentication login use-radius local radius
aaa authentication enable default enable
aaa authentication ppp default if-needed local tacacs+
aaa authentication ppp use-radius if-needed local radius
aaa authentication arap default local
aaa authorization exec default tacacs+ local
aaa authorization exec console none
aaa authorization exec use-radius local radius if-authenticated
aaa authorization network default local tacacs+ if-authenticated
aaa authorization network use-radius local radius if-authenticated
aaa accounting exec default stop-only tacacs+
aaa accounting network default stop-only tacacs+
aaa accounting system default start-stop tacacs+
enable secret 5 $1$oMKx$kPcop1zxkpxa8fkxXBWp21
!
modem call-record terse
modem buffer-size 250
no ip finger
!
isdn switch-type primary-5ess
clock timezone PST -8
clock summer-time PDT recurring
!

controller T1 0
 framing esf
 clock source line primary
 linecode b8zs
 pri-group timeslots 1-24

<output omitted>

!
interface Loopback0
 ip address 10.1.1.1 255.255.255.0
 no ip directed-broadcast
!
interface Ethernet0
 ip address 172.16.1.1 255.255.255.0
 no ip directed-broadcast
!
interface Virtual-Template1
 ip unnumbered Loopback0
 no ip directed-broadcast
 no keepalive
 peer default ip address pool default
 ppp authentication chap pap use-radius
 ppp multilink
!
interface Serial0:23
 ip unnumbered Loopback0
 no ip directed-broadcast
 encapsulation ppp
 no logging event link-status
 no keepalive
 dialer-group 1
 autodetect encapsulation ppp v120
 isdn switch-type primary-5ess
 isdn incoming-voice modem
 peer default ip address pool default
 no fair-queue
 no cdp enable
 ppp max-bad-auth 3
 ppp authentication chap pap use-radius
 ppp multilink
!

<output omitted>

!
interface Group-Async1
 ip unnumbered Loopback0
 no ip directed-broadcast
 encapsulation ppp
 no logging event link-status
 async mode interactive
 peer default ip address pool default
 no fair-queue
 no cdp enable
 ppp max-bad-auth 3
 ppp authentication chap pap use-radius
 ppp multilink
 group-range 1 96
 hold-queue 10 in
!
ip local pool default 10.1.1.2 10.1.1.200
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.1.254
!
no logging console
dialer-list 1 protocol ip permit
tacacs-server host 172.16.1.201
tacacs-server key cisco
radius-server host 172.16.1.202 auth-port 1645 acct-port 1646 key cisco
!
line con 0
 exec-timeout 0 0
 authorization exec console
 login authentication console
 transport input none
line 1 96
 autoselect during-login
 autoselect ppp
 modem Dialin
 escape-character BREAK
 authorization exec use-radius
 login authentication use-radius
line aux 0
line vty 0 4
 exec-timeout 60 0
!
end

Délais d'attente globaux

Pour l'exemple suivant, nous imposerons un délai d'attente d'inactif de 30 minutes (1800 secondes) et une temporisation absolue de trois heures (de 180 minutes) pour des utilisateurs. La modification de configuration de delta qui activera des délais d'attente globaux de ppp sera comme suit :

interface Serial0:23
 dialer idle-timeout 1800
 timeout absolute 180
!

<output omitted>

!
interface Group=Async1
 dialer in-band
 dialer idle-timeout 1800
 dialer-group 1
 timeout absolute 180

Si vous n'avez pas un dialer-list 1, vous devrez définir un. Le plus simple serait autorisation d'IP de protocole du dialer-list 1.

Si vous utilisiez des Profils virtuels, votre configuration peut être plus facile parce que vous pouvez juste mettre le délai d'attente sur l'interface de modèle virtuel, comme affiché ci-dessous :

interface Virtual-Template1
 ppp timeout idle 1800
 timeout absolute 180

Délais d'attente de Par-utilisateur - Configuration du serveur d'AAA

Maintenant que nous avons travaillé aux délais d'attente globaux, nous étendrons cette connaissance aux délais d'attente de par-utilisateur. Vos valeurs de temporisateur de par-utilisateur seront livré vers le bas pendant l'autorisation de réseau, ainsi vous devez avoir la commande d'aaa authorization network configurée à Qu'est ce que méthode vous utilisez, qui est RAYON ou TACACS+. Notez également que les temporisateurs de par-utilisateur ignoreront toujours toutes les valeurs globales qui sont préconfigurées sur le NAS. La manière que le travail de temporisateurs de par-utilisateur est que quand le serveur d'accès reçoit le délai d'attente attribue pendant la phase d'autorisation de réseau, ce traduira ces attributs en ensemble de commandes de configuration qui seront sélectionnées dans l'interface à laquelle l'utilisateur sera connecté. Ces commandes de configuration qui sont sélectionnées dans l'interface par un processus en arrière-plan sont provisoires ; ils sont retirés quand les débranchements d'utilisateur.

Répertoriés ci-dessous sont plusieurs profils utilisateurs d'échantillon sur le serveur :

Profils RADIUS

timeout-absolute-ppp Password = "cisco"
        Service-Type = Framed,
        Framed-Protocol = PPP,
        Framed-IP-Address = 255.255.255.254,
        Session-Timeout = 600

timeout-idle-ppp Password = "cisco"
        Service-Type = Framed,
        Framed-Protocol = PPP
        Framed-IP-Address = 255.255.255.254,
        Idle-Timeout = 300

timeout-both-ppp Password = "cisco"
        Service-Type = Framed,
        Framed-Protocol = PPP,
        Framed-IP-Address = 255.255.255.254,
        Session-Timeout = 600,
        Idle-Timeout = 300

Remarque: Votre syntaxe peut varier selon la façon dont votre dictionnaire est installé.

Profils TACACS+

user = timeout-absolute-ppp { 
        chap = cleartext cisco 
        service = ppp protocol = lcp { 
                timeout = 10 
        } 
        service = ppp protocol = ip { 
                addr-pool = "default" 
        } 
} 

user = timeout-idle-ppp { 
        chap = cleartext cisco 
        service = ppp protocol = lcp { 
                idletime = 5 
        } 
        service = ppp protocol = ip { 
                addr-pool = "default" 
        } 
} 

user = timeout-both-ppp { 
        chap = cleartext cisco 
        service = ppp protocol = lcp { 
                timeout = 10 
                idletime = 5 
        } 
        service = ppp protocol = multilink { } 
        service = ppp protocol = ip { 
                addr-pool = "default" 
        } 
}

Délais d'attente de Par-utilisateur - Configuration de NAS

Si vous êtes faire seulement async (aucun RNIS), et pas utilisant des Profils virtuels, tant que vous avez le dialer in-band configuré sur (ou le group-async) les interfaces async, les temporisateurs de par-utilisateur devraient fonctionner. Le processus en arrière-plan insérera les temporisateurs sur l'interface asynchrone, utilisant les commandes de dialer idle-timeout et de timeout absolute avec les valeurs passées dedans de RADIUS/TACACS+, et les enlève quand les débranchements d'utilisateur.

Si vous êtes faire seulement async (aucun RNIS), et utilisez des Profils virtuels, vous n'avez pas besoin de dialer in-band configuré sur (ou de group-async) l'interface async. Il devrait juste fonctionner. Le processus en arrière-plan insérera les temporisateurs sur les vaccess se connectent par interface, utilisant les commandes de ppp timeout idle et de timeout absolute aux valeurs passées dedans de RADIUS/TACACS+, et les enlèvent quand les débranchements d'utilisateur.

Si vous avez les utilisateurs RNIS et vous le besoin de faire des temporisateurs de par-utilisateur, vous pouvez devoir utiliser des Profils virtuels. La raison est parce que le processus en arrière-plan que nous avons discuté préalablement ne fonctionne pas pour des interfaces RNIS ; c'est-à-dire, vous ne pouvez pas configurer le canal B auquel l'utilisateur est connecté. La seule chose que vous pouvez configurer est le canal D qui affecte chacun. Cependant si un utilisateur négocie le multilink sur une session, le serveur d'accès créera automatiquement une interface d'accès virtuel qui agit en tant qu'interface de paquet pour l'utilisateur. Le processus en arrière-plan travaille aux interfaces d'accès virtuel, mais cela ne fonctionne pas sur un appel de non-Multilien le RNIS où il n'y a aucune interface d'accès virtuel. Ainsi, si vous aurez des utilisateurs simples de canal B qui ne négocient pas le multilink et vous voulez installer des délais d'attente de par-utilisateur pour eux, vous devez activer des Profils virtuels. Activant des Profils virtuels force une création d'une interface de vaccess pour tous les utilisateurs (pas simplement les utilisateurs de multilink) et le processus en arrière-plan peut avec succès insérer les commandes de ppp timeout idle et de timeout absolute. Si vous choisissez de ne pas activer des Profils virtuels, les utilisateurs asynchrones et les utilisateurs RNIS de multilink pourront avoir des délais d'attente de par-utilisateur appliqués à eux. Mais, les utilisateurs RNIS de non-Multilien ne peuvent pas avoir des délais d'attente de par-utilisateur appliqués à eux. Seulement les délais d'attente globaux statiquement configurés sur l'interface (le cas échéant) s'appliqueront. Si vous essayez de s'appliquer des délais d'attente de par-utilisateur à un utilisateur RNIS de non-Multilien et ne faites pas activer des Profils virtuels, la connexion utilisateur échouera autorisation parce que le serveur d'accès ne pouvait pas traiter les attributs obligatoires de délai d'attente de par-utilisateur.

Supplémentaire, une caractéristique a été ajoutée au Cisco IOS 11.3(8.1)T et aux versions ultérieures qui permet des délais d'attente de par-utilisateur à appliquer aux utilisateurs RNIS de non-Multilien. Il essentiellement saute le mode de configuration de processus en arrière-plan qui est habituellement utilisé et place les temporisateurs directement sur le canal B sans utiliser l'interface de ligne de commande.

Pour récapituler cette installation compliquée, voici deux vous ordonne peut suivre :

  • Sinon utilisant des Profils virtuels, configurez le dialer in-band sur les interfaces asynchrones et le Cisco IOS 11.3(8.1)T de passage ou plus tard. Si vous êtes le Cisco IOS courant 11.3(8)T, prenez garde que les utilisateurs RNIS de non-Multilien ne peuvent pas avoir des délais d'attente de par-utilisateur appliqués à eux, autrement ils ne se connecteront pas.

  • Si utilisant des Profils virtuels, le Cisco IOS 11.3(8)T ou plus tard fonctionnera bien.

Vérifiez

Aucune procédure de vérification n'est disponible pour cette configuration.

Dépannez

Cette section fournit des informations que vous pouvez utiliser pour dépanner votre configuration. Aux fins du débogage, six exemples de sortie d'appel sont inclus. Pour brancher directement à une section particulière, sélectionnez un des liens ci-dessous :

Certaines commandes show sont prises en charge par l'Output Interpreter Tool (clients enregistrés uniquement), qui vous permet de voir une analyse de la sortie de la commande show.

Remarque: Avant d'émettre des commandes de débogage, référez-vous aux informations importantes sur des commandes de debug.

Remarque:  Pour voir les mêmes commandes et sortie qui sont présentées ci-dessous, vous devez être Cisco IOS courant version 11.3AA ou version 12.0T.

Appel asynchrone avec des Profils virtuels - La connexion ne tourne pas au ralenti

Est ci-dessous un appel asynchrone avec des Profils virtuels. Le profil installe une seconde temporisation absolue 90 et un seconde délai d'attente 60 de veille. Dans cet exemple, nous ne permettrons pas l'inactif de connexion. Voyez les commentaires dans la sortie ci-dessous pour plus de détails. Des commentaires sont mis en valeur et en texte en italiques.


!--- ISDN setup message comes in.

*Mar  4 19:21:47.772: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x09
*Mar  4 19:21:47.772:         Bearer Capability i = 0x9090A2
*Mar  4 19:21:47.772:         Channel ID i = 0xA98393
*Mar  4 19:21:47.772:         Called Party Number i = 0xC1, '4085703932'
*Mar  4 19:21:47.776: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0x8009
*Mar  4 19:21:47.776:         Channel ID i = 0xA98393
*Mar  4 19:21:47.776: ISDN Se0:23: TX ->  ALERTING pd = 8  callref = 0x8009

!--- Modem is allocated.

*Mar  4 19:21:47.776: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x3D, ces=0x1
   bchan=0x12, event=0x1, cause=0x0

*Mar  4 19:21:47.776: VDEV_ALLOCATE: slot 1 and port 28 is allocated.

*Mar  4 19:21:47.776: EVENT_FROM_ISDN:(003D): DEV_INCALL at slot 1 and port 28

*Mar  4 19:21:47.776: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 1, port 28
*Mar  4 19:21:47.776: Mica Modem(1/28): Configure(0x1 = 0x0) 
*Mar  4 19:21:47.776: Mica Modem(1/28): Configure(0x23 = 0x0) 
*Mar  4 19:21:47.776: Mica Modem(1/28): Call Setup
*Mar  4 19:21:47.932: Mica Modem(1/28): State Transition to Call Setup

!--- Modem goes offhook.

*Mar  4 19:21:47.932: Mica Modem(1/28): Went offhook
*Mar  4 19:21:47.932: CSM_PROC_IC1_RING: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 28
*Mar  4 19:21:47.932: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0x8009
*Mar  4 19:21:47.996: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x09

!--- DS0 is cut-through.

*Mar  4 19:21:47.996: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x3D, ces=0x1
   bchan=0x12, event=0x4, cause=0x0

*Mar  4 19:21:47.996: EVENT_FROM_ISDN:(003D): DEV_CONNECTED at slot 1 and port 28

*Mar  4 19:21:47.996: CSM_PROC_IC4_WAIT_FOR_CARRIER: CSM_EVENT_ISDN_CONNECTED 
at slot 1, port 28

!--- Modem training starts.

*Mar  4 19:21:47.996: Mica Modem(1/28): Link Initiate
*Mar  4 19:21:49.140: Mica Modem(1/28): State Transition to Connect
*Mar  4 19:21:54.276: Mica Modem(1/28): State Transition to Link
*Mar  4 19:22:05.828: Mica Modem(1/28): State Transition to Trainup
*Mar  4 19:22:09.028: Mica Modem(1/28): State Transition to EC Negotiating
*Mar  4 19:22:09.568: Mica Modem(1/28): State Transition to Steady State

!--- Modem training completes.

*Mar  4 19:22:10.128: AAA: parse NAME=tty53 idb TYPE=10 tty=53
*Mar  4 19:22:10.128: AAA: NAME=tty53 flags=0x11 TYPE=4 shelf=0 slot=0 adapter=0 port=53 
channel=0
*Mar  4 19:22:10.128: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:22:10.128: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 adapter=0 
port=0 channel=18

!--- PPP begins negotiation.

*Mar  4 19:22:11.332: As53 LCP: Lower layer not up, Fast Starting
*Mar  4 19:22:11.332: As53 PPP: Treating connection as a dedicated line
*Mar  4 19:22:11.332: As53 AAA/AUTHOR/FSM: (0): LCP succeeds trivially

!--- LCP negotiation completes, authentication begins.

*Mar  4 19:22:13.556: As53 PPP: Phase is AUTHENTICATING, by this end
*Mar  4 19:22:13.556: As53 CHAP: O CHALLENGE id 1 len 26 from "STACK"
*Mar  4 19:22:16.016: As53 AUTH: Started process 0 pid 45
*Mar  4 19:22:16.016: As53 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:22:16.208: As53 PPP: Phase is AUTHENTICATING, by this end
*Mar  4 19:22:16.208: As53 CHAP: O CHALLENGE id 2 len 26 from "STACK"

!--- CHAP response received from client.

*Mar  4 19:22:16.304: As53 CHAP: I RESPONSE id 2 len 30 from "timeout"
*Mar  4 19:22:16.304: AAA: parse NAME=Async53 idb TYPE=10 tty=53
*Mar  4 19:22:16.304: AAA: NAME=Async53 flags=0x11 TYPE=4 shelf=0 slot=0 
adapter=0 port=53 channel=0
*Mar  4 19:22:16.304: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:22:16.304: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 
adapter=0 port=0 channel=18

!--- Send RADIUS query.

*Mar  4 19:22:16.304: RADIUS: ustruct sharecount=1
*Mar  4 19:22:16.304: RADIUS: Initial Transmit Async53 id 0 172.16.24.117:1645, 
Access-Request, len 92
*Mar  4 19:22:16.304:         Attribute 4 6 AC101874
*Mar  4 19:22:16.304:         Attribute 5 6 00000035
*Mar  4 19:22:16.304:         Attribute 61 6 00000000
*Mar  4 19:22:16.304:         Attribute 1 11 74696D65
*Mar  4 19:22:16.304:         Attribute 30 12 34303835
*Mar  4 19:22:16.304:         Attribute 3 19 0283D0F9
*Mar  4 19:22:16.308:         Attribute 6 6 00000002
*Mar  4 19:22:16.308:         Attribute 7 6 00000001

!--- Received RADIUS response, note attribute 27 (Session-Timeout -> absolute timeout) 
!--- is 0x5A (90) and attribute 28 (Idle-Timeout) is 0x3C (60).

*Mar  4 19:22:16.316: RADIUS: Received from id 0 172.16.24.117:1645, 
Access-Accept, len 50
*Mar  4 19:22:16.316:         Attribute 6 6 00000002
*Mar  4 19:22:16.320:         Attribute 7 6 00000001
*Mar  4 19:22:16.320:         Attribute 8 6 FFFFFFFE
*Mar  4 19:22:16.320:         Attribute 27 6 0000005A
*Mar  4 19:22:16.320:         Attribute 28 6 0000003C

!--- Start LCP authorization.

*Mar  4 19:22:16.320: As53 AAA/AUTHOR/LCP: Authorize LCP
*Mar  4 19:22:16.320: AAA/AUTHOR/LCP As53 (3506139973): Port='Async53' list='' 
service=NET
*Mar  4 19:22:16.320: AAA/AUTHOR/LCP: As53 (3506139973) send AV service=ppp
*Mar  4 19:22:16.320: AAA/AUTHOR/LCP: As53 (3506139973) send AV protocol=lcp
*Mar  4 19:22:16.320: AAA/AUTHOR/LCP (3506139973) found list "default"
*Mar  4 19:22:16.320: AAA/AUTHOR/LCP: As53 (3506139973) METHOD=RADIUS
*Mar  4 19:22:16.320: AAA/AUTHOR (3506139973): Post authorization status = PASS_REPL

!--- Gleaned per-user timeouts from user profile.

*Mar  4 19:22:16.320: As53 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar  4 19:22:16.320: As53 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar  4 19:22:16.320: As53 AAA/AUTHOR/LCP: Processing AV idletime=60

!--- Translate AAA attributes to interface configuration commands. 
!--- Since we are using virtual-profiles, we will use the "ppp timeout idle" 
!--- command instead of the "dialer in-band" command. Note that 90 second absolute timeout 
!--- translates to the command "timeout absolute 1 30" (1 minute and 30 seconds).

*Mar  4 19:22:16.320: AAA/AUTHOR/LCP As53: Per-user interface config created:
timeout absolute 1 30
ppp timeout idle 60


!--- PPP authentication succeeds.

*Mar  4 19:22:16.320: As53 CHAP: O SUCCESS id 2 len 4
*Mar  4 19:22:16.320: AAA/ACCT/NET/START User timeout, Port Async53, List ""
*Mar  4 19:22:16.320: AAA/ACCT/NET: Found list "default"

!--- Create new vaccess interface.

*Mar  4 19:22:16.416: VTEMPLATE: No unused vaccess, create new vaccess
*Mar  4 19:22:16.416: Vi1 VTEMPLATE: Set default settings with no ip address, encap ppp
*Mar  4 19:22:16.440: Vi1 VTEMPLATE: Hardware address 00e0.1e81.636c
*Mar  4 19:22:16.440: Vi1 VTEMPLATE: Has a new cloneblk vtemplate, now it has vtemplate
*Mar  4 19:22:16.440: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar  4 19:22:16.440: Vi1 VTEMPLATE: Clone from Virtual-Template1
interface Virtual-Access1
default ip address
no ip address
encap ppp
ip unnumbered Loopback0
ip access-group 199 in
ip helper-address 172.16.24.118
no ip directed-broadcast
ip accounting output-packets
ip nat inside
no keepalive
peer default ip address pool default
compress mppc
ppp callback accept
ppp authentication chap pap ms-chap
ppp multilink
multilink max-links 2
end

*Mar  4 19:22:16.504: Vi1 CCP: Re-Syncing history using legacy method

!--- Now add the per-user timeouts we constructed for this user.

*Mar  4 19:22:16.520: Vi1 VTEMPLATE: Has a new cloneblk AAA, now it has vtemplate/AAA
*Mar  4 19:22:16.520: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar  4 19:22:16.520: Vi1 VTEMPLATE: Clone from AAA
interface Virtual-Access1
timeout absolute 1 30
ppp timeout idle 60
end


!--- LCP layer is finished, negotiate the appropriate NCPs.

*Mar  4 19:22:16.532: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
*Mar  4 19:22:16.536: Vi1 PPP: Treating connection as a dedicated line
*Mar  4 19:22:16.536: Vi1 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:22:16.536: Vi1 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM Vi1 (1906691625): Port='Async53' list='' service=NET
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (1906691625) send AV service=ppp
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (1906691625) send AV protocol=ip
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM (1906691625) found list "default"
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (1906691625) METHOD=RADIUS
*Mar  4 19:22:16.536: RADIUS: Using NAS default peer
*Mar  4 19:22:16.536: RADIUS: Authorize IP address 0.0.0.0
*Mar  4 19:22:16.536: AAA/AUTHOR (1906691625): Post authorization status = PASS_REPL
*Mar  4 19:22:16.536: Vi1 AAA/AUTHOR/FSM: We can start IPCP
*Mar  4 19:22:16.536: Vi1 AAA/AUTHOR/FSM: (0): Can we start CCP?
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM Vi1 (282953275): Port='Async53' list='' service=NET
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (282953275) send AV service=ppp
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (282953275) send AV protocol=ccp
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM (282953275) found list "default"
*Mar  4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (282953275) METHOD=RADIUS
*Mar  4 19:22:16.540: AAA/AUTHOR (282953275): Post authorization status = PASS_REPL
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/FSM: We can start CCP
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 0.0.0.0
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 0.0.0.0
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar  4 19:22:16.540: Vi1 AAA/AUTHOR/FSM: Succeeded
*Mar  4 19:22:16.656: Vi1 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar  4 19:22:16.656: Vi1 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar  4 19:22:16.656: Vi1 AAA/AUTHOR/FSM: Succeeded
*Mar  4 19:22:17.536: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, 
changed state to up
*Mar  4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 10.1.1.3
*Mar  4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar  4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 10.1.1.3
*Mar  4 19:22:19.608: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 10.1.1.3
*Mar  4 19:22:19.608: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:22:19.608: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar  4 19:22:19.608: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:22:19.612: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 10.1.1.3
*Mar  4 19:22:19.704: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 10.1.1.3, we want 10.1.1.3
*Mar  4 19:22:19.704: AAA/AUTHOR/IPCP Vi1 (785695075): Port='Async53' list='' service=NET
*Mar  4 19:22:19.708: AAA/AUTHOR/IPCP: Vi1 (785695075) send AV service=ppp
*Mar  4 19:22:19.708: AAA/AUTHOR/IPCP: Vi1 (785695075) send AV protocol=ip
*Mar  4 19:22:19.708: AAA/AUTHOR/IPCP: Vi1 (785695075) send AV addr*10.1.1.3
*Mar  4 19:22:19.708: AAA/AUTHOR/IPCP (785695075) found list "default"
*Mar  4 19:22:19.708: AAA/AUTHOR/IPCP: Vi1 (785695075) METHOD=RADIUS
*Mar  4 19:22:19.708: RADIUS: Using NAS default peer
*Mar  4 19:22:19.708: RADIUS: Authorize IP address 10.1.1.3
*Mar  4 19:22:19.708: AAA/AUTHOR (785695075): Post authorization status = PASS_REPL
*Mar  4 19:22:19.708: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:22:19.708: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.3
*Mar  4 19:22:19.708: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:22:19.708: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 10.1.1.3, we want 10.1.1.3
*Mar  4 19:22:19.708: Vi1 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar  4 19:22:19.708: Vi1 AAA/PER-USER: processing author params.


!--- PPP negotiation finished, user is connected.



!--- User is connected on line 53, async interface 53 and vaccess 1. The "show caller" 
!--- command shows active time and idle time for this user in Cisco IOS 11.3(8.1)AA or later.

access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time
  tty 53       timeout          Async         00:00:20  00:00:02  
  As53         timeout          PPP           00:00:13  00:00:02  
  Vi1          timeout          PPP   VDP     00:00:13  00:00:11  

!--- The "show caller timeout" command shows the installed absolute and idle timeout as well 
!--- as how much time before the user is disconnected by any timeouts. Note the timeouts 
!--- only show up on the vaccess interface.

 access-3#show caller timeouts
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  tty 53       timeout          -         -         -         
  As53         timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:43  

!--- The "show caller user" command gives more detailed information about the user as well as 
!--- providing a breakdown of the active and idle time, absolute and idle timeout, 
!--- and time to disconnect for both idle and absolute timeout.

access-3#show caller user timeout

  User: timeout, line tty 53, service Async
        Active time 00:00:31, Idle time 00:00:12
  Timeouts:            Absolute  Idle      Idle
                                 Session   Exec
      Limits:          -         -         00:10:00  
      Disconnect in:   -         -         -         
  TTY: Line 53, running PPP on As53
  Location: MICA V.90 modems
  Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
  Status: Ready, Active, No Exit Banner, Async Interface Active
          HW PPP Support Active
  Capabilities: No Flush-at-Activation, Hardware Flowcontrol In
                Hardware Flowcontrol Out, Modem Callout, Modem RI is CD
                Line usable as async interface, ARAP Permitted
                Integrated Modem
  Modem State: Ready

  User: timeout, line As53, service PPP
        Active time 00:00:23, Idle time 00:00:12
  Timeouts:            Absolute  Idle
      Limits:          -         -         
      Disconnect in:   -         -         
  PPP: LCP Open, multilink Closed, CHAP (<- AAA)
  IP: Local 10.1.1.1
  Counts: 35 packets input, 820 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          22 packets output, 517 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

  User: timeout, line Vi1, service PPP VDP
        Active time 00:00:24, Idle time 00:00:22
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:01:05  00:00:37  
  PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP, CCP
       Idle timer 60 secs, idle 22 secs
  IP: Local 10.1.1.1, remote 10.1.1.3
      Access list (I/O) is 199/not set
  Counts: 24 packets input, 542 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          19 packets output, 167 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  tty 53       timeout          -         -         -         
  As53         timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:35  
access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time
  tty 53       timeout          Async         00:00:45  00:00:27  
  As53         timeout          PPP           00:00:38  00:00:27  
  Vi1          timeout          PPP   VDP     00:00:38  00:00:36

!--- User has been idle for 36 seconds and will be disconnected in 24 seconds. Let's
!--- ping the user to see what happens.

access-3#ping 10.1.1.3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 92/108/132 ms

!--- Now the idle timer has been reset, so we won't disconnect the user for another 
!--- 58 seconds.

access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  tty 53       timeout          -         -         -         
  As53         timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:58

!--- Ping again to reset the idle timer.

access-3#ping 10.1.1.3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 96/98/108 ms

!--- But note, the disconnect timer did not go back to 1 minute. The reason is because the
!--- absolute timer is going to start soon.

access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  tty 53       timeout          -         -         -         
  As53         timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:24  
access-3#show caller user timeout

  User: timeout, line tty 53, service Async
        Active time 00:01:23, Idle time 00:00:11
  Timeouts:            Absolute  Idle      Idle
                                 Session   Exec
      Limits:          -         -         00:10:00  
      Disconnect in:   -         -         -         
  TTY: Line 53, running PPP on As53
  Location: MICA V.90 modems
  Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
  Status: Ready, Active, No Exit Banner, Async Interface Active
          HW PPP Support Active
  Capabilities: No Flush-at-Activation, Hardware Flowcontrol In
                Hardware Flowcontrol Out, Modem Callout, Modem RI is CD
                Line usable as async interface, ARAP Permitted
                Integrated Modem
  Modem State: Ready

  User: timeout, line As53, service PPP
        Active time 00:01:15, Idle time 00:00:11
  Timeouts:            Absolute  Idle
      Limits:          -         -         
      Disconnect in:   -         -         
  PPP: LCP Open, multilink Closed, CHAP (<- AAA)
  IP: Local 10.1.1.1
  Counts: 45 packets input, 1161 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          32 packets output, 897 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

  User: timeout, line Vi1, service PPP VDP
        Active time 00:01:16, Idle time 00:00:12
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:00:13  00:00:47  
  PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP, CCP
       Idle timer 60 secs, idle 12 secs
  IP: Local 10.1.1.1, remote 10.1.1.3
      Access list (I/O) is 199/not set
  Counts: 34 packets input, 883 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          39 packets output, 547 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

!--- User is disconnected.
*Mar  4 19:23:47.536: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
*Mar  4 19:23:47.536: Vi1 VTEMPLATE: Free vaccess
*Mar  4 19:23:47.540: As53 AAA/ACCT: non-ISDN xmit 50000 recv 28800 hwidb 613307E0 ttynum 53
!--- Send accounting stop record, includes disc-cause 5 (session-timeout) and 
!--- disc-cause-ext 1100 (session-timeout).
*Mar  4 19:23:47.540: AAA/ACCT/NET/STOP User timeout, Port Async53:
         task_id=9 timezone=PST service=ppp protocol=ip addr=10.1.1.3 disc-cause=5 
disc-cause-ext=1100 
pre-bytes-in=184 pre-bytes-out=330 pre-paks-in=7 pre-paks-out=11 bytes_in=950 
bytes_out=567 paks_in=37 
paks_out=21 pre-session-time=5 elapsed_time=91 nas-rx-speed=28800 nas-tx-speed=50000 
*Mar  4 19:23:47.540: Vi1 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar  4 19:23:47.540: Vi1 AAA/AUTHOR/PER-USER: Event LCP_DOWN
!--- Modem hangs up.
*Mar  4 19:23:47.580: Mica Modem(1/28): State Transition to Terminating
*Mar  4 19:23:47.640: Mica Modem(1/28): State Transition to Idle
*Mar  4 19:23:47.640: Mica Modem(1/28): Went onhook
*Mar  4 19:23:47.640: CSM_PROC_IC5_OC6_CONNECTED: CSM_EVENT_MODEM_ONHOOK at slot 1, port 28
*Mar  4 19:23:47.640: VDEV_DEALLOCATE: slot 1 and port 28 is deallocated

*Mar  4 19:23:47.640: ISDN Se0:23: Event: Hangup call to call id 0x3D 

!--- ISDN call is terminated.

*Mar  4 19:23:47.640: ISDN Se0:23: TX ->  DISCONNECT pd = 8  callref = 0x8009
*Mar  4 19:23:47.640:         Cause i = 0x8090 - Normal call clearing 
*Mar  4 19:23:47.688: ISDN Se0:23: RX <-  RELEASE pd = 8  callref = 0x09
*Mar  4 19:23:47.696: ISDN Se0:23: TX ->  RELEASE_COMP pd = 8  callref = 0x8009
*Mar  4 19:23:47.744: TAC+: (866083896): received acct response status = SUCCESS

!--- Per-user timeouts are taken off the vaccess interface.

*Mar  4 19:23:48.140: VTEMPLATE: Clean up dirty vaccess queue, size 1
*Mar  4 19:23:48.140: Vi1 VTEMPLATE: Found a dirty vaccess clone with vtemplate/AAA
*Mar  4 19:23:48.140: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar  4 19:23:48.140: Vi1 VTEMPLATE: Unclone to-be-freed command#2
interface Virtual-Access1
default ppp timeout idle 60
default timeout absolute 1 30
end


!--- vaccess interface is cleaned up.

*Mar  4 19:23:48.160: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar  4 19:23:48.176: Vi1 VTEMPLATE: Remove cloneblk AAA with vtemplate/AAA
*Mar  4 19:23:48.180: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar  4 19:23:48.180: Vi1 VTEMPLATE: Unclone to-be-freed command#15
interface Virtual-Access1
default multilink max-links 2
default ppp multilink
default ppp authentication chap pap ms-chap
default ppp callback accept
default compress mppc
default peer default ip address pool default
default keepalive
default ip nat inside
default ip accounting output-packets
default ip directed-broadcast
default ip helper-address 172.16.24.118
default ip access-group 199 in
default ip unnumbered Loopback0
default encap ppp
default ip address
end

*Mar  4 19:23:48.264: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar  4 19:23:48.284: Vi1 VTEMPLATE: Remove cloneblk vtemplate with vtemplate/AAA
*Mar  4 19:23:48.284: Vi1 VTEMPLATE: Add vaccess to recycle queue, queue SIZE=1

!--- Here is the call record for the user. Note the disconnect reason is Session-Timeout
!--- (absolute timeout).

*Mar  4 19:23:48.300: %CALLRECORD-3-MICA_TERSE_CALL_REC: DS0 slot/contr/chan=2/0/18, 
slot/port=1/28, call_id=3D, userid=timeout, ip=10.1.1.3, calling=(n/a), called=4085703932, 
std=K56Flx, prot=LAP-M, comp=V.42bis both, init-rx/tx b-rate=28800/50000, finl-rx/tx 
b-rate=28800/50000, rbs=0, d-pad=6 dB, retr=0, sq=3, snr=32, rx/tx chars=1274/1477, bad=4, 
rx/tx ec=45/61, bad=3, time=118, finl-state=Steady, disc(radius)=Session Timeout/Session Timeout, 
disc(modem)=DF03 Tx (host to line) data flushing - OK/Requested by host/DTR dropped
*Mar  4 19:23:48.536: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, 
changed state to down
*Mar  4 19:23:49.536: As53 AAA/AUTHOR/PER-USER: Event LCP_DOWN

Appel asynchrone avec des Profils virtuels - La connexion tourne au ralenti

Est ci-dessous un appel asynchrone avec des Profils virtuels. Il a le même nom d'utilisateur que l'exemple ci-dessus. Le profil installe une seconde temporisation absolue 90 et un seconde délai d'attente 60 de veille. Dans cet exemple, nous permettrons l'inactif de connexion. Il n'y a aucun commentaire ci-dessous, mais l'importante sortie a été mise en valeur.

*Mar  4 19:24:38.768: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x0A
*Mar  4 19:24:38.768:         Bearer Capability i = 0x9090A2
*Mar  4 19:24:38.768:         Channel ID i = 0xA98393
*Mar  4 19:24:38.768:         Called Party Number i = 0xC1, '4085703932'
*Mar  4 19:24:38.772: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0x800A
*Mar  4 19:24:38.772:         Channel ID i = 0xA98393
*Mar  4 19:24:38.772: ISDN Se0:23: TX ->  ALERTING pd = 8  callref = 0x800A
*Mar  4 19:24:38.772: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x3E, ces=0x1
   bchan=0x12, event=0x1, cause=0x0

*Mar  4 19:24:38.772: VDEV_ALLOCATE: slot 1 and port 29 is allocated.

*Mar  4 19:24:38.772: EVENT_FROM_ISDN:(003E): DEV_INCALL at slot 1 and port 29

*Mar  4 19:24:38.772: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 1, port 29
*Mar  4 19:24:38.772: Mica Modem(1/29): Configure(0x1 = 0x0) 
*Mar  4 19:24:38.772: Mica Modem(1/29): Configure(0x23 = 0x0) 
*Mar  4 19:24:38.772: Mica Modem(1/29): Call Setup
*Mar  4 19:24:38.908: Mica Modem(1/29): State Transition to Call Setup
*Mar  4 19:24:38.908: Mica Modem(1/29): Went offhook
*Mar  4 19:24:38.908: CSM_PROC_IC1_RING: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 29
*Mar  4 19:24:38.912: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0x800A
*Mar  4 19:24:38.972: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x0A
*Mar  4 19:24:38.976: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x3E, ces=0x1
   bchan=0x12, event=0x4, cause=0x0

*Mar  4 19:24:38.976: EVENT_FROM_ISDN:(003E): DEV_CONNECTED at slot 1 and port 29

*Mar  4 19:24:38.976: CSM_PROC_IC4_WAIT_FOR_CARRIER: CSM_EVENT_ISDN_CONNECTED at 
slot 1, port 29
*Mar  4 19:24:38.976: Mica Modem(1/29): Link Initiate
*Mar  4 19:24:40.060: Mica Modem(1/29): State Transition to Connect
*Mar  4 19:24:45.256: Mica Modem(1/29): State Transition to Link
*Mar  4 19:24:56.796: Mica Modem(1/29): State Transition to Trainup
*Mar  4 19:24:59.996: Mica Modem(1/29): State Transition to EC Negotiating
*Mar  4 19:25:00.532: Mica Modem(1/29): State Transition to Steady State
*Mar  4 19:25:01.340: AAA: parse NAME=tty54 idb TYPE=10 tty=54
*Mar  4 19:25:01.340: AAA: NAME=tty54 flags=0x11 TYPE=4 shelf=0 slot=0 
adapter=0 port=54 channel=0
*Mar  4 19:25:01.340: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:25:01.340: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 
adapter=0 port=0 channel=18
*Mar  4 19:25:02.544: As54 LCP: Lower layer not up, Fast Starting
*Mar  4 19:25:02.544: As54 PPP: Treating connection as a dedicated line
*Mar  4 19:25:02.544: As54 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:25:04.744: As54 PPP: Phase is AUTHENTICATING, by this end
*Mar  4 19:25:04.744: As54 CHAP: O CHALLENGE id 1 len 26 from "STACK"
*Mar  4 19:25:06.628: As54 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:25:06.820: As54 PPP: Phase is AUTHENTICATING, by this end
*Mar  4 19:25:06.820: As54 CHAP: O CHALLENGE id 2 len 26 from "STACK"
*Mar  4 19:25:06.916: As54 CHAP: I RESPONSE id 2 len 30 from "timeout"
*Mar  4 19:25:06.916: AAA: parse NAME=Async54 idb TYPE=10 tty=54
*Mar  4 19:25:06.916: AAA: NAME=Async54 flags=0x11 TYPE=4 shelf=0 slot=0 
adapter=0 port=54 channel=0
*Mar  4 19:25:06.916: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:25:06.916: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 
adapter=0 port=0 channel=18
*Mar  4 19:25:06.916: RADIUS: ustruct sharecount=1
*Mar  4 19:25:06.916: RADIUS: Initial Transmit Async54 id 1 172.16.24.117:1645, 
Access-Request, len 92
*Mar  4 19:25:06.916:         Attribute 4 6 AC101874
*Mar  4 19:25:06.916:         Attribute 5 6 00000036
*Mar  4 19:25:06.916:         Attribute 61 6 00000000
*Mar  4 19:25:06.916:         Attribute 1 11 74696D65
*Mar  4 19:25:06.916:         Attribute 30 12 34303835
*Mar  4 19:25:06.916:         Attribute 3 19 024525C7
*Mar  4 19:25:06.916:         Attribute 6 6 00000002
*Mar  4 19:25:06.916:         Attribute 7 6 00000001
*Mar  4 19:25:06.924: RADIUS: Received from id 1 172.16.24.117:1645, 
Access-Accept, len 50
*Mar  4 19:25:06.924:         Attribute 6 6 00000002
*Mar  4 19:25:06.924:         Attribute 7 6 00000001
*Mar  4 19:25:06.924:         Attribute 8 6 FFFFFFFE
*Mar  4 19:25:06.924:         Attribute 27 6 0000005A
*Mar  4 19:25:06.928:         Attribute 28 6 0000003C
*Mar  4 19:25:06.928: As54 AAA/AUTHOR/LCP: Authorize LCP
*Mar  4 19:25:06.928: AAA/AUTHOR/LCP As54 (2013841092): Port='Async54' list='' service=NET
*Mar  4 19:25:06.928: AAA/AUTHOR/LCP: As54 (2013841092) send AV service=ppp
*Mar  4 19:25:06.928: AAA/AUTHOR/LCP: As54 (2013841092) send AV protocol=lcp
*Mar  4 19:25:06.928: AAA/AUTHOR/LCP (2013841092) found list "default"
*Mar  4 19:25:06.928: AAA/AUTHOR/LCP: As54 (2013841092) METHOD=RADIUS
*Mar  4 19:25:06.928: AAA/AUTHOR (2013841092): Post authorization status = PASS_REPL
*Mar  4 19:25:06.928: As54 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar  4 19:25:06.928: As54 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar  4 19:25:06.928: As54 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar  4 19:25:06.928: AAA/AUTHOR/LCP As54: Per-user interface config created:
timeout absolute 1 30
ppp timeout idle 60

*Mar  4 19:25:06.928: As54 CHAP: O SUCCESS id 2 len 4
*Mar  4 19:25:06.928: AAA/ACCT/NET/START User timeout, Port Async54, List ""
*Mar  4 19:25:06.928: AAA/ACCT/NET: Found list "default"
*Mar  4 19:25:07.028: Vi1 VTEMPLATE: Reuse Vi1, recycle queue size 0
*Mar  4 19:25:07.028: Vi1 VTEMPLATE: Hardware address 00e0.1e81.636c
*Mar  4 19:25:07.028: Vi1 VTEMPLATE: Has a new cloneblk vtemplate, now it has vtemplate
*Mar  4 19:25:07.028: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar  4 19:25:07.028: Vi1 VTEMPLATE: Clone from Virtual-Template1
interface Virtual-Access1
default ip address
no ip address
encap ppp
ip unnumbered Loopback0
ip access-group 199 in
ip helper-address 172.16.24.118
no ip directed-broadcast
ip accounting output-packets
ip nat inside
no keepalive
peer default ip address pool default
compress mppc
ppp callback accept
ppp authentication chap pap ms-chap
ppp multilink
multilink max-links 2
end

*Mar  4 19:25:07.092: Vi1 CCP: Re-Syncing history using legacy method
*Mar  4 19:25:07.108: Vi1 VTEMPLATE: Has a new cloneblk AAA, now it has vtemplate/AAA
*Mar  4 19:25:07.108: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar  4 19:25:07.108: Vi1 VTEMPLATE: Clone from AAA
interface Virtual-Access1
timeout absolute 1 30
ppp timeout idle 60
end

*Mar  4 19:25:07.120: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
*Mar  4 19:25:07.124: Vi1 PPP: Treating connection as a dedicated line
*Mar  4 19:25:07.124: Vi1 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:25:07.124: Vi1 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar  4 19:25:07.124: AAA/AUTHOR/FSM Vi1 (3979277251): Port='Async54' list='' service=NET
*Mar  4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (3979277251) send AV service=ppp
*Mar  4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (3979277251) send AV protocol=ip
*Mar  4 19:25:07.124: AAA/AUTHOR/FSM (3979277251) found list "default"
*Mar  4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (3979277251) METHOD=RADIUS
*Mar  4 19:25:07.124: RADIUS: Using NAS default peer
*Mar  4 19:25:07.124: RADIUS: Authorize IP address 0.0.0.0
*Mar  4 19:25:07.124: AAA/AUTHOR (3979277251): Post authorization status = PASS_REPL
*Mar  4 19:25:07.124: Vi1 AAA/AUTHOR/FSM: We can start IPCP
*Mar  4 19:25:07.124: Vi1 AAA/AUTHOR/FSM: (0): Can we start CCP?
*Mar  4 19:25:07.124: AAA/AUTHOR/FSM Vi1 (1524934880): Port='Async54' list='' service=NET
*Mar  4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (1524934880) send AV service=ppp
*Mar  4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (1524934880) send AV protocol=ccp
*Mar  4 19:25:07.128: AAA/AUTHOR/FSM (1524934880) found list "default"
*Mar  4 19:25:07.128: AAA/AUTHOR/FSM: Vi1 (1524934880) METHOD=RADIUS
*Mar  4 19:25:07.128: AAA/AUTHOR (1524934880): Post authorization status = PASS_REPL
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/FSM: We can start CCP
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 0.0.0.0
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 0.0.0.0
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar  4 19:25:07.128: Vi1 AAA/AUTHOR/FSM: Succeeded
*Mar  4 19:25:07.236: Vi1 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar  4 19:25:07.236: Vi1 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar  4 19:25:07.236: Vi1 AAA/AUTHOR/FSM: Succeeded
*Mar  4 19:25:08.120: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, 
changed state to up
*Mar  4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 10.1.1.3
*Mar  4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar  4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 10.1.1.3
*Mar  4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 10.1.1.3
*Mar  4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar  4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 10.1.1.3
*Mar  4 19:25:10.316: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 10.1.1.3, we want 10.1.1.3
*Mar  4 19:25:10.316: AAA/AUTHOR/IPCP Vi1 (2714455877): Port='Async54' list='' service=NET
*Mar  4 19:25:10.316: AAA/AUTHOR/IPCP: Vi1 (2714455877) send AV service=ppp
*Mar  4 19:25:10.316: AAA/AUTHOR/IPCP: Vi1 (2714455877) send AV protocol=ip
*Mar  4 19:25:10.316: AAA/AUTHOR/IPCP: Vi1 (2714455877) send AV addr*10.1.1.3


*Mar  4 19:25:10.316: AAA/AUTHOR/IPCP (2714455877) found list "default"
*Mar  4 19:25:10.316: AAA/AUTHOR/IPCP: Vi1 (2714455877) METHOD=RADIUS
*Mar  4 19:25:10.316: RADIUS: Using NAS default peer
*Mar  4 19:25:10.320: RADIUS: Authorize IP address 10.1.1.3
*Mar  4 19:25:10.320: AAA/AUTHOR (2714455877): Post authorization status = PASS_REPL
*Mar  4 19:25:10.320: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:25:10.320: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.3
*Mar  4 19:25:10.320: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:25:10.320: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 10.1.1.3, we want 10.1.1.3
*Mar  4 19:25:10.320: Vi1 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar  4 19:25:10.320: Vi1 AAA/PER-USER: processing author params.

access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time
  tty 54       timeout          Async         00:00:17  00:00:01  
  As54         timeout          PPP           00:00:10  00:00:01  
  Vi1          timeout          PPP   VDP     00:00:10  00:00:08  
access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time
  tty 54       timeout          Async         00:00:27  00:00:11  
  As54         timeout          PPP           00:00:20  00:00:11  
  Vi1          timeout          PPP   VDP     00:00:20  00:00:18  
access-3#show caller user timeout

  User: timeout, line tty 54, service Async
        Active time 00:00:49, Idle time 00:00:34
  Timeouts:            Absolute  Idle      Idle
                                 Session   Exec
      Limits:          -         -         00:10:00  
      Disconnect in:   -         -         -         
  TTY: Line 54, running PPP on As54
  Location: MICA V.90 modems
  Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
  Status: Ready, Active, No Exit Banner, Async Interface Active
          HW PPP Support Active
  Capabilities: No Flush-at-Activation, Hardware Flowcontrol In
                Hardware Flowcontrol Out, Modem Callout, Modem RI is CD
                Line usable as async interface, ARAP Permitted
                Integrated Modem
  Modem State: Ready

  User: timeout, line As54, service PPP
        Active time 00:00:43, Idle time 00:00:34
  Timeouts:            Absolute  Idle
      Limits:          -         -         
      Disconnect in:   -         -         
  PPP: LCP Open, multilink Closed, CHAP (<- AAA)
  IP: Local 10.1.1.1
  Counts: 35 packets input, 824 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          22 packets output, 517 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

  User: timeout, line Vi1, service PPP VDP
        Active time 00:00:43, Idle time 00:00:41
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:00:45  00:00:18  
  PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP, CCP
       Idle timer 60 secs, idle 41 secs
  IP: Local 10.1.1.1, remote 10.1.1.3
      Access list (I/O) is 199/not set
  Counts: 24 packets input, 546 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          19 packets output, 167 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

access-3#show caller timeouts
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  tty 54       timeout          -         -         -         
  As54         timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:05  

*Mar  4 19:26:10.320: Vi1 PPP: Idle timeout, dropping connection
*Mar  4 19:26:10.320: As54 AAA/ACCT: non-ISDN xmit 50000 recv 28800 hwidb 613360C8 ttynum 54
*Mar  4 19:26:10.320: AAA/ACCT/NET/STOP User timeout, Port Async54:
         task_id=10 timezone=PST service=ppp protocol=ip addr=10.1.1.3 disc-cause=4 
disc-cause-ext=1021 pre-bytes-in=184 pre-bytes-out=330 pre-paks-in=7 pre-paks-out=11 
bytes_in=613 bytes_out=187 paks_in=27 paks_out=11 pre-session-time=4 elapsed_time=63 
nas-rx-speed=28800 nas-tx-speed=50000 
*Mar  4 19:26:10.320: Vi1 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar  4 19:26:10.324: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
*Mar  4 19:26:10.324: Vi1 VTEMPLATE: Free vaccess
*Mar  4 19:26:10.328: Vi1 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:26:10.376: Mica Modem(1/29): State Transition to Terminating
*Mar  4 19:26:10.436: Mica Modem(1/29): State Transition to Idle
*Mar  4 19:26:10.436: Mica Modem(1/29): Went onhook
*Mar  4 19:26:10.436: CSM_PROC_IC5_OC6_CONNECTED: CSM_EVENT_MODEM_ONHOOK at slot 1, 
port 29
*Mar  4 19:26:10.440: VDEV_DEALLOCATE: slot 1 and port 29 is deallocated

*Mar  4 19:26:10.440: ISDN Se0:23: Event: Hangup call to call id 0x3E 
*Mar  4 19:26:10.440: ISDN Se0:23: TX ->  DISCONNECT pd = 8  callref = 0x800A
*Mar  4 19:26:10.440:         Cause i = 0x8090 - Normal call clearing 
*Mar  4 19:26:10.488: ISDN Se0:23: RX <-  RELEASE pd = 8  callref = 0x0A
*Mar  4 19:26:10.496: ISDN Se0:23: TX ->  RELEASE_COMP pd = 8  callref = 0x800A
*Mar  4 19:26:10.528: TAC+: (2047544826): received acct response status = SUCCESS
*Mar  4 19:26:11.180: VTEMPLATE: Clean up dirty vaccess queue, size 1
*Mar  4 19:26:11.180: Vi1 VTEMPLATE: Found a dirty vaccess clone with vtemplate/AAA
*Mar  4 19:26:11.180: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar  4 19:26:11.180: Vi1 VTEMPLATE: Unclone to-be-freed command#2
interface Virtual-Access1
default ppp timeout idle 60
default timeout absolute 1 30
end

*Mar  4 19:26:11.200: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar  4 19:26:11.216: Vi1 VTEMPLATE: Remove cloneblk AAA with vtemplate/AAA
*Mar  4 19:26:11.216: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar  4 19:26:11.216: Vi1 VTEMPLATE: Unclone to-be-freed command#15
interface Virtual-Access1
default multilink max-links 2
default ppp multilink
default ppp authentication chap pap ms-chap
default ppp callback accept
default compress mppc
default peer default ip address pool default
default keepalive
default ip nat inside
default ip accounting output-packets
default ip directed-broadcast
default ip helper-address 172.16.24.118
default ip access-group 199 in
default ip unnumbered Loopback0
default encap ppp
default ip address
end

*Mar  4 19:26:11.304: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar  4 19:26:11.324: Vi1 VTEMPLATE: Remove cloneblk vtemplate with vtemplate/AAA
*Mar  4 19:26:11.324: Vi1 VTEMPLATE: Add vaccess to recycle queue, queue SIZE=1
*Mar  4 19:26:11.324: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, 
changed state to down
*Mar  4 19:26:11.460: Mica Modem(1/29): State Transition to Terminating
*Mar  4 19:26:11.520: Mica Modem(1/29): State Transition to Idle
*Mar  4 19:26:12.200: %CALLRECORD-3-MICA_TERSE_CALL_REC: DS0 slot/contr/chan=2/0/18, 
slot/port=1/29, call_id=3E, userid=timeout, ip=10.1.1.3, calling=(n/a), called=4085703932, 
std=K56Flx, prot=LAP-M, comp=V.42bis both, init-rx/tx b-rate=28800/50000, finl-rx/tx 
b-rate=28800/50000, rbs=0, d-pad=6 dB, retr=0, sq=3, snr=34, rx/tx chars=918/1138, bad=5, 
rx/tx ec=35/47, bad=0, time=90, finl-state=Steady, disc(radius)=Idle Timeout/Idle Timeout, 
disc(modem)=DF03 Tx (host to line) data flushing - OK/Requested by host/DTR dropped
*Mar  4 19:26:12.320: As54 AAA/AUTHOR/PER-USER: Event LCP_DOWN

Appel asynchrone sans Profils virtuels

Est ci-dessous un appel asynchrone sans Profils virtuels activés. Notez que la commande de dialer idle-timeout est utilisée au lieu de la commande de ppp timeout idle puisque nous n'utilisons pas des Profils virtuels et il n'y a aucune interface de vaccess. Vous nous verrez également ne créer la commande de délai d'attente de par-utilisateur et, en même temps, l'aucune version des commandes. Les commandes de temporisateur de par-utilisateur sont installées immédiatement, alors que l'aucune version des commandes ne sont mises en file d'attente à l'interface à traiter quand les débranchements d'utilisateur.

*Mar  4 19:30:28.420: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x06
*Mar  4 19:30:28.420:         Bearer Capability i = 0x9090A2
*Mar  4 19:30:28.420:         Channel ID i = 0xA98393
*Mar  4 19:30:28.420:         Called Party Number i = 0xC1, '4085703932'
*Mar  4 19:30:28.420: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0x8006
*Mar  4 19:30:28.420:         Channel ID i = 0xA98393
*Mar  4 19:30:28.424: ISDN Se0:23: TX ->  ALERTING pd = 8  callref = 0x8006
*Mar  4 19:30:28.424: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x40, ces=0x1
   bchan=0x12, event=0x1, cause=0x0

*Mar  4 19:30:28.424: VDEV_ALLOCATE: slot 1 and port 2 is allocated.

*Mar  4 19:30:28.424: EVENT_FROM_ISDN:(0040): DEV_INCALL at slot 1 and port 2

*Mar  4 19:30:28.424: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 1, port 2
*Mar  4 19:30:28.424: Mica Modem(1/2): Configure(0x1 = 0x0) 
*Mar  4 19:30:28.424: Mica Modem(1/2): Configure(0x23 = 0x0) 
*Mar  4 19:30:28.424: Mica Modem(1/2): Call Setup
*Mar  4 19:30:28.552: Mica Modem(1/2): State Transition to Call Setup
*Mar  4 19:30:28.552: Mica Modem(1/2): Went offhook
*Mar  4 19:30:28.552: CSM_PROC_IC1_RING: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 2
*Mar  4 19:30:28.552: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0x8006
*Mar  4 19:30:28.604: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x06
*Mar  4 19:30:28.604: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x40, ces=0x1
   bchan=0x12, event=0x4, cause=0x0

*Mar  4 19:30:28.604: EVENT_FROM_ISDN:(0040): DEV_CONNECTED at slot 1 and port 2

*Mar  4 19:30:28.604: CSM_PROC_IC4_WAIT_FOR_CARRIER: CSM_EVENT_ISDN_CONNECTED 
at slot 1, port 2
*Mar  4 19:30:28.604: Mica Modem(1/2): Link Initiate
*Mar  4 19:30:29.692: Mica Modem(1/2): State Transition to Connect
*Mar  4 19:30:34.888: Mica Modem(1/2): State Transition to Link
*Mar  4 19:30:46.408: Mica Modem(1/2): State Transition to Trainup
*Mar  4 19:30:49.612: Mica Modem(1/2): State Transition to EC Negotiating
*Mar  4 19:30:50.156: Mica Modem(1/2): State Transition to Steady State
*Mar  4 19:30:50.592: AAA: parse NAME=tty27 idb TYPE=10 tty=27
*Mar  4 19:30:50.592: AAA: NAME=tty27 flags=0x11 TYPE=4 shelf=0 slot=0 
adapter=0 port=27 channel=0
*Mar  4 19:30:50.592: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:30:50.592: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 
adapter=0 port=0 channel=18
*Mar  4 19:30:51.792: As27 LCP: Lower layer not up, Fast Starting
*Mar  4 19:30:51.792: As27 PPP: Treating connection as a callin
*Mar  4 19:30:51.792: As27 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:30:57.468: As27 PPP: Phase is AUTHENTICATING, by this end
*Mar  4 19:30:57.468: As27 CHAP: O CHALLENGE id 1 len 26 from "STACK"
*Mar  4 19:30:57.564: As27 CHAP: I RESPONSE id 1 len 30 from "timeout"
*Mar  4 19:30:57.564: AAA: parse NAME=Async27 idb TYPE=10 tty=27
*Mar  4 19:30:57.564: AAA: NAME=Async27 flags=0x11 TYPE=4 shelf=0 slot=0 
adapter=0 port=27 channel=0
*Mar  4 19:30:57.564: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:30:57.564: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 
adapter=0 port=0 channel=18
*Mar  4 19:30:57.564: RADIUS: ustruct sharecount=1
*Mar  4 19:30:57.564: RADIUS: Initial Transmit Async27 id 3 172.16.24.117:1645, 
Access-Request, len 92
*Mar  4 19:30:57.564:         Attribute 4 6 AC101874
*Mar  4 19:30:57.564:         Attribute 5 6 0000001B
*Mar  4 19:30:57.564:         Attribute 61 6 00000000
*Mar  4 19:30:57.564:         Attribute 1 11 74696D65
*Mar  4 19:30:57.564:         Attribute 30 12 34303835
*Mar  4 19:30:57.564:         Attribute 3 19 01E5C3F6
*Mar  4 19:30:57.564:         Attribute 6 6 00000002
*Mar  4 19:30:57.564:         Attribute 7 6 00000001
*Mar  4 19:30:57.572: RADIUS: Received from id 3 172.16.24.117:1645, 
Access-Accept, len 50
*Mar  4 19:30:57.572:         Attribute 6 6 00000002
*Mar  4 19:30:57.572:         Attribute 7 6 00000001
*Mar  4 19:30:57.572:         Attribute 8 6 FFFFFFFE
*Mar  4 19:30:57.572:         Attribute 27 6 0000005A
*Mar  4 19:30:57.572:         Attribute 28 6 0000003C
*Mar  4 19:30:57.572: As27 AAA/AUTHOR/LCP: Authorize LCP
*Mar  4 19:30:57.572: AAA/AUTHOR/LCP As27 (1969884263): Port='Async27' list='' 
service=NET
*Mar  4 19:30:57.572: AAA/AUTHOR/LCP: As27 (1969884263) send AV service=ppp
*Mar  4 19:30:57.572: AAA/AUTHOR/LCP: As27 (1969884263) send AV protocol=lcp
*Mar  4 19:30:57.572: AAA/AUTHOR/LCP (1969884263) found list "default"
*Mar  4 19:30:57.572: AAA/AUTHOR/LCP: As27 (1969884263) METHOD=RADIUS
*Mar  4 19:30:57.572: AAA/AUTHOR (1969884263): Post authorization status = PASS_REPL
*Mar  4 19:30:57.572: As27 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar  4 19:30:57.572: As27 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar  4 19:30:57.572: As27 AAA/AUTHOR: Parse 'interface Async27'
*Mar  4 19:30:57.576: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar  4 19:30:57.576: As27 AAA/AUTHOR: Parse 'timeout absolute 1 30'
*Mar  4 19:30:57.580: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar  4 19:30:57.580: As27 AAA/AUTHOR: enqueue peruser LCP txt=interface Async27
no timeout absolute

*Mar  4 19:30:57.580: As27 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar  4 19:30:57.580: As27 AAA/AUTHOR: Parse 'interface Async27'
*Mar  4 19:30:57.584: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar  4 19:30:57.584: As27 AAA/AUTHOR: Parse 'dialer idle-timeout 60'
*Mar  4 19:30:57.588: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar  4 19:30:57.588: As27 AAA/AUTHOR: enqueue peruser LCP txt=interface Async27
no dialer idle-timeout

*Mar  4 19:30:57.588: As27 CHAP: O SUCCESS id 1 len 4
*Mar  4 19:30:57.588: AAA/ACCT/NET/START User timeout, Port Async27, List ""
*Mar  4 19:30:57.588: AAA/ACCT/NET: Found list "default"
*Mar  4 19:30:57.692: As27 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar  4 19:30:57.692: AAA/AUTHOR/FSM As27 (2088523207): Port='Async27' list='' 
service=NET
*Mar  4 19:30:57.692: AAA/AUTHOR/FSM: As27 (2088523207) send AV service=ppp
*Mar  4 19:30:57.692: AAA/AUTHOR/FSM: As27 (2088523207) send AV protocol=ip
*Mar  4 19:30:57.692: AAA/AUTHOR/FSM (2088523207) found list "default"
*Mar  4 19:30:57.692: AAA/AUTHOR/FSM: As27 (2088523207) METHOD=RADIUS
*Mar  4 19:30:57.692: RADIUS: Using NAS default peer
*Mar  4 19:30:57.692: RADIUS: Authorize IP address 10.1.1.6
*Mar  4 19:30:57.692: AAA/AUTHOR (2088523207): Post authorization status = PASS_REPL
*Mar  4 19:30:57.692: As27 AAA/AUTHOR/FSM: We can start IPCP
*Mar  4 19:30:57.784: As27 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 10.1.1.6
*Mar  4 19:30:57.788: As27 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:30:57.788: As27 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.6
*Mar  4 19:30:57.788: As27 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:30:57.788: As27 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 10.1.1.6
*Mar  4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 10.1.1.6
*Mar  4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.6
*Mar  4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 10.1.1.6
*Mar  4 19:31:00.884: As27 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 10.1.1.6
*Mar  4 19:31:00.884: As27 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:31:00.884: As27 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.6
*Mar  4 19:31:00.884: As27 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:31:00.888: As27 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 10.1.1.6
*Mar  4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Start.  Her address 10.1.1.6, we want 10.1.1.6
*Mar  4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.6
*Mar  4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Done.  Her address 10.1.1.6, we want 10.1.1.6
*Mar  4 19:31:00.984: As27 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar  4 19:31:00.984: As27 AAA/PER-USER: processing author params.

access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time
  tty 27       timeout          Async         00:00:23  00:00:04  
  As27         timeout          PPP           00:00:22  00:00:20  
access-3#show caller user timeout

  User: timeout, line tty 27, service Async
        Active time 00:00:28, Idle time 00:00:08
  Timeouts:            Absolute  Idle      Idle
                                 Session   Exec
      Limits:          -         -         00:10:00  
      Disconnect in:   -         -         -         
  TTY: Line 27, running PPP on As27
  Location: MICA V.90 modems
  Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
  Status: Ready, Active, No Exit Banner, Async Interface Active
          HW PPP Support Active
  Capabilities: No Flush-at-Activation, Hardware Flowcontrol In
                Hardware Flowcontrol Out, Modem Callout, Modem RI is CD
                Line usable as async interface, ARAP Permitted
                Integrated Modem
  Modem State: Ready

  User: timeout, line As27, service PPP
        Active time 00:00:27, Idle time 00:00:25
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:01:09  00:00:34  
  PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP
  Dialer: Connected, inbound
          Idle timer 60 secs, idle 25 secs
          Type is IN-BAND ASYNC, group Async27
  IP: Local 10.1.1.1, remote 10.1.1.6
  Counts: 31 packets input, 1642 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          15 packets output, 347 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

access-3#show caller timeouts
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  tty 27       timeout          -         -         -         
  As27         timeout          00:01:30  00:01:00  00:00:22  
access-3#show caller timeouts
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  tty 27       timeout          -         -         -         
  As27         timeout          00:01:30  00:01:00  00:00:07  
access-3#
*Mar  4 19:31:53.824: Mica Modem(1/2): State Transition to Terminating
*Mar  4 19:31:53.884: Mica Modem(1/2): State Transition to Idle
*Mar  4 19:31:53.884: Mica Modem(1/2): Went onhook
*Mar  4 19:31:53.884: CSM_PROC_IC5_OC6_CONNECTED: CSM_EVENT_MODEM_ONHOOK at slot 1, port 2
*Mar  4 19:31:53.884: VDEV_DEALLOCATE: slot 1 and port 2 is deallocated

*Mar  4 19:31:53.888: ISDN Se0:23: Event: Hangup call to call id 0x40 
*Mar  4 19:31:53.888: ISDN Se0:23: TX ->  DISCONNECT pd = 8  callref = 0x8006
*Mar  4 19:31:53.888:         Cause i = 0x8090 - Normal call clearing 
*Mar  4 19:31:53.940: ISDN Se0:23: RX <-  RELEASE pd = 8  callref = 0x06
*Mar  4 19:31:53.952: ISDN Se0:23: TX ->  RELEASE_COMP pd = 8  callref = 0x8006
*Mar  4 19:31:55.792: As27 AAA/ACCT: non-ISDN xmit 50000 recv 28800 hwidb 611CEBC0 ttynum 27
*Mar  4 19:31:55.792: AAA/ACCT/NET/STOP User timeout, Port Async27:
         task_id=12 timezone=PST service=ppp protocol=ip addr=10.1.1.6 disc-cause=4 
disc-cause-ext=1021 pre-bytes-in=135 pre-bytes-out=176 pre-paks-in=5 pre-paks-out=6 
bytes_in=1480 bytes_out=171 paks_in=25 paks_out=9 pre-session-time=6 elapsed_time=58 
nas-rx-speed=28800 nas-tx-speed=50000 
*Mar  4 19:31:55.792: As27 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar  4 19:31:55.792: As27 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:31:55.792: As27 AAA/AUTHOR: down_event: peruser LCP txt=interface Async27
no timeout absolute

*Mar  4 19:31:55.796: As27 AAA/AUTHOR: Parse 'interface Async27'
*Mar  4 19:31:55.800: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar  4 19:31:55.800: As27 AAA/AUTHOR: Parse 'no timeout absolute'
*Mar  4 19:31:55.804: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar  4 19:31:55.804: As27 AAA/AUTHOR: free peruser LCP txt=interface Async27
no timeout absolute

*Mar  4 19:31:55.804: As27 AAA/AUTHOR: down_event: peruser LCP txt=interface Async27
no dialer idle-timeout

*Mar  4 19:31:55.804: As27 AAA/AUTHOR: Parse 'interface Async27'
*Mar  4 19:31:55.808: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar  4 19:31:55.808: As27 AAA/AUTHOR: Parse 'no dialer idle-timeout'
*Mar  4 19:31:55.812: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar  4 19:31:55.812: As27 AAA/AUTHOR: free peruser LCP txt=interface Async27
no dialer idle-timeout

*Mar  4 19:31:56.016: TAC+: (3633056702): received acct response status = SUCCESS
*Mar  4 19:32:00.308: %CALLRECORD-3-MICA_TERSE_CALL_REC: DS0 slot/contr/chan=2/0/18, 
slot/port=1/2, call_id=40, userid=timeout, ip=10.1.1.6, calling=(n/a), called=4085703932, 
std=K56Flx, prot=LAP-M, comp=V.42bis both, init-rx/tx b-rate=28800/50000, finl-rx/tx 
b-rate=28800/50000, rbs=0, d-pad=6 dB, retr=0, sq=3, snr=28, rx/tx chars=1727/995, bad=2, 
rx/tx ec=31/36, bad=0, time=84, finl-state=Steady, disc(radius)=Idle Timeout/Idle Timeout, 
disc(modem)=DF03 Tx (host to line) data flushing - OK/Requested by host/DTR dropped

Appel du canal unique le RNIS de Multilien sans Profils virtuels

Est ci-dessous un appel du multilink le RNIS sans Profils virtuels activés. Puisqu'un appel multiliaison crée les vaccess relient, les temporisateurs peuvent être installés facilement.

*Mar  4 19:41:12.208: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x08
*Mar  4 19:41:12.212:         Bearer Capability i = 0x8890
*Mar  4 19:41:12.212:         Channel ID i = 0xA98393
*Mar  4 19:41:12.212:         Calling Party Number i = '!', 0x80, '4085551200'
*Mar  4 19:41:12.212:         Called Party Number i = 0xA1, '4085703930'
*Mar  4 19:41:12.212: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0x8008
*Mar  4 19:41:12.212:         Channel ID i = 0xA98393
*Mar  4 19:41:12.224: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0x8008
*Mar  4 19:41:12.224:         Channel ID i = 0xA98393
*Mar  4 19:41:12.296: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x08
*Mar  4 19:41:12.536: Se0:18 PPP: Treating connection as a callin
*Mar  4 19:41:12.536: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:41:14.536: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:41:14.552: Se0:18 PPP: Phase is AUTHENTICATING, by this end
*Mar  4 19:41:14.552: Se0:18 CHAP: O CHALLENGE id 1 len 26 from "STACK"
*Mar  4 19:41:14.584: Se0:18 CHAP: I RESPONSE id 1 len 30 from "timeout"
*Mar  4 19:41:14.964: Se0:18 CHAP: I RESPONSE id 1 len 30 from "timeout"
*Mar  4 19:41:14.964: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:41:14.964: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 
adapter=0 port=0 channel=18
*Mar  4 19:41:14.964: AAA: parse NAME= idb TYPE=-1 tty=-1
*Mar  4 19:41:14.964: RADIUS: ustruct sharecount=1
*Mar  4 19:41:14.964: RADIUS: Initial Transmit Serial0:18 id 4 172.16.24.117:1645, 
Access-Request, len 104
*Mar  4 19:41:14.964:         Attribute 4 6 AC101874
*Mar  4 19:41:14.964:         Attribute 5 6 00004E32
*Mar  4 19:41:14.964:         Attribute 61 6 00000002
*Mar  4 19:41:14.964:         Attribute 1 11 74696D65
*Mar  4 19:41:14.964:         Attribute 30 12 34303835
*Mar  4 19:41:14.964:         Attribute 31 12 34303835
*Mar  4 19:41:14.964:         Attribute 3 19 012C4E14
*Mar  4 19:41:14.964:         Attribute 6 6 00000002
*Mar  4 19:41:14.964:         Attribute 7 6 00000001
*Mar  4 19:41:14.972: RADIUS: Received from id 4 172.16.24.117:1645, Access-Accept, len 50
*Mar  4 19:41:14.972:         Attribute 6 6 00000002
*Mar  4 19:41:14.972:         Attribute 7 6 00000001
*Mar  4 19:41:14.972:         Attribute 8 6 FFFFFFFE
*Mar  4 19:41:14.972:         Attribute 27 6 0000005A
*Mar  4 19:41:14.972:         Attribute 28 6 0000003C
*Mar  4 19:41:14.976: Se0:18 AAA/AUTHOR/LCP: Authorize LCP
*Mar  4 19:41:14.976: AAA/AUTHOR/LCP Se0:18 (4039479425): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:41:14.976: AAA/AUTHOR/LCP: Se0:18 (4039479425) send AV service=ppp
*Mar  4 19:41:14.976: AAA/AUTHOR/LCP: Se0:18 (4039479425) send AV protocol=lcp
*Mar  4 19:41:14.976: AAA/AUTHOR/LCP (4039479425) found list "default"
*Mar  4 19:41:14.976: AAA/AUTHOR/LCP: Se0:18 (4039479425) METHOD=RADIUS
*Mar  4 19:41:14.976: AAA/AUTHOR (4039479425): Post authorization status = PASS_REPL
*Mar  4 19:41:14.976: Se0:18 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar  4 19:41:14.976: Se0:18 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar  4 19:41:14.976: Se0:18 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar  4 19:41:14.976: AAA/AUTHOR/LCP Se0:18: Per-user interface config created:
timeout absolute 1 30
ppp timeout idle 60

*Mar  4 19:41:14.976: Se0:18 CHAP: O SUCCESS id 1 len 4
*Mar  4 19:41:14.976: AAA/ACCT/NET/START User timeout, Port Serial0:18, List ""
*Mar  4 19:41:14.976: AAA/ACCT/NET: Found list "default"
*Mar  4 19:41:14.976: AAA/AUTHOR/MLP Se0:18 (1966034416): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:41:14.976: AAA/AUTHOR/MLP: Se0:18 (1966034416) send AV service=ppp
*Mar  4 19:41:14.976: AAA/AUTHOR/MLP: Se0:18 (1966034416) send AV protocol=multilink
*Mar  4 19:41:14.976: AAA/AUTHOR/MLP (1966034416) found list "default"
*Mar  4 19:41:14.976: AAA/AUTHOR/MLP: Se0:18 (1966034416) METHOD=RADIUS
*Mar  4 19:41:14.976: AAA/AUTHOR (1966034416): Post authorization status = PASS_REPL
*Mar  4 19:41:14.976: Vi1 VTEMPLATE: Reuse Vi1, recycle queue size 0
*Mar  4 19:41:14.980: Vi1 VTEMPLATE: Hardware address 00e0.1e81.636c
*Mar  4 19:41:14.980: Vi1 VTEMPLATE: Has a new cloneblk dialer, now it has dialer
*Mar  4 19:41:14.980: Vi1 VTEMPLATE: Has a new cloneblk AAA, now it has dialer/AAA
*Mar  4 19:41:14.980: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar  4 19:41:14.980: Vi1 VTEMPLATE: Clone from AAA
interface Virtual-Access1
timeout absolute 1 30
ppp timeout idle 60
end

*Mar  4 19:41:14.996: Vi1 PPP: Treating connection as a callin
*Mar  4 19:41:14.996: AAA/AUTHOR/MLP Vi1: Processing AV service=ppp
*Mar  4 19:41:15.000: Vi1 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM Vi1 (921779905): Port='Serial0:18' list='' service=NET
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (921779905) send AV service=ppp
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (921779905) send AV protocol=ip
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM (921779905) found list "default"
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (921779905) METHOD=RADIUS
*Mar  4 19:41:15.000: RADIUS: Using NAS default peer
*Mar  4 19:41:15.000: RADIUS: Authorize IP address 0.0.0.0
*Mar  4 19:41:15.000: AAA/AUTHOR (921779905): Post authorization status = PASS_REPL
*Mar  4 19:41:15.000: Vi1 AAA/AUTHOR/FSM: We can start IPCP
*Mar  4 19:41:15.000: Vi1 AAA/AUTHOR/FSM: (0): Can we start CDPCP?
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM Vi1 (3065122210): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (3065122210) send AV service=ppp
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (3065122210) send AV protocol=cdp
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM (3065122210) found list "default"
*Mar  4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (3065122210) METHOD=RADIUS
*Mar  4 19:41:15.000: AAA/AUTHOR (3065122210): Post authorization status = PASS_REPL
*Mar  4 19:41:15.000: Vi1 AAA/AUTHOR/FSM: We can start CDPCP

access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time
  Se0:18       timeout          PPP           00:00:19  00:00:00  
  Vi1          timeout          PPP   Bundle  00:00:19  00:00:20  
access-3#show caller user timeout

  User: timeout, line Se0:18, service PPP
        Active time 00:00:25, Idle time 00:00:00
  Timeouts:            Absolute  Idle
      Limits:          -         -         
      Disconnect in:   -         -         
  PPP: LCP Open, multilink Open, CHAP (<- AAA)
  Dialer: Connected to 4085551200, inbound
          Type is ISDN, group Serial0:23
  IP: Local 10.1.1.1
      Access list (I/O) is 199/not set
  Bundle: Member of timeout/timeout, last input 00:00:00
  Counts: 13 packets input, 279 bytes, 0 no buffer
          11 input errors, 2 CRC, 3 frame, 0 overrun
          23 packets output, 431 bytes, 0 underruns
          0 output errors, 0 collisions, 40 interface resets

  User: timeout, line Vi1, service PPP Bundle
        Active time 00:00:25, Idle time 00:00:26
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:01:04  00:00:33  
  PPP: LCP Open, multilink Open
       Idle timer 60 secs, idle 26 secs
  Dialer: Connected to 4085551200, inbound
          Type is IN-BAND SYNC, group Serial0:23
  IP: Local 10.1.1.1
      Access list (I/O) is 199/not set
  Bundle: First link of timeout/timeout, 1 link, last input 00:00:27
  Counts: 0 packets input, 0 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          13 packets output, 236 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:30  
access-3#
*Mar  4 19:42:14.996: Vi1 PPP: Idle timeout, dropping connection
*Mar  4 19:42:14.996: Vi1 VTEMPLATE: Free vaccess
*Mar  4 19:42:14.996: Se0:18 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:42:15.000: Vi1 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:42:15.004: Se0:18 AAA/ACCT: ISDN xmit 64000 recv 64000 hwidb 612048BC
*Mar  4 19:42:15.004: AAA/ACCT/NET/STOP User timeout, Port Serial0:18:
         task_id=13 timezone=PST service=ppp mlp-links-max=1 mlp-links-current=1 
mlp-sess-id=0 disc-cause=18 disc-cause-ext=1046 pre-bytes-in=125 pre-bytes-out=99 
pre-paks-in=4 pre-paks-out=4 bytes_in=228 bytes_out=436 paks_in=15 paks_out=26 
pre-session-time=3 elapsed_time=60 nas-rx-speed=64000 nas-tx-speed=64000 
*Mar  4 19:42:15.008: ISDN Se0:23: TX ->  DISCONNECT pd = 8  callref = 0x8008
*Mar  4 19:42:15.008:         Cause i = 0x8090 - Normal call clearing 
*Mar  4 19:42:15.060: ISDN Se0:23: RX <-  RELEASE pd = 8  callref = 0x08
*Mar  4 19:42:15.072: ISDN Se0:23: TX ->  RELEASE_COMP pd = 8  callref = 0x8008
*Mar  4 19:42:15.212: TAC+: (2571416724): received acct response status = SUCCESS
*Mar  4 19:42:15.500: VTEMPLATE: Clean up dirty vaccess queue, size 1
*Mar  4 19:42:15.500: Vi1 VTEMPLATE: Found a dirty vaccess clone with dialer/AAA
*Mar  4 19:42:15.500: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar  4 19:42:15.500: Vi1 VTEMPLATE: Unclone to-be-freed command#2
interface Virtual-Access1
default ppp timeout idle 60
default timeout absolute 1 30
end

*Mar  4 19:42:15.516: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar  4 19:42:15.536: Vi1 VTEMPLATE: Remove cloneblk AAA with dialer/AAA
*Mar  4 19:42:15.536: Vi1 VTEMPLATE: Remove cloneblk dialer with dialer/AAA
*Mar  4 19:42:15.536: Vi1 VTEMPLATE: Add vaccess to recycle queue, queue SIZE=1

Appel du canal unique le RNIS de Non-Multilien sans Profils virtuels

Est ci-dessous un appel du canal unique le RNIS de non-Multilien sans Profils virtuels activés. Dans cet exemple, nous sommes le Cisco IOS courant 11.3(8.2)AA ainsi ces temporisateurs peuvent être installés correctement. Cependant, notez qu'aucune commande de configuration n'a été créée d'entraîner ceci ; les temporisateurs ont été placés intérieurement dans le code.

*Mar  4 19:43:00.404: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x0E
*Mar  4 19:43:00.404:         Bearer Capability i = 0x8890
*Mar  4 19:43:00.404:         Channel ID i = 0xA98393
*Mar  4 19:43:00.404:         Calling Party Number i = '!', 0x80, '4085551200'
*Mar  4 19:43:00.404:         Called Party Number i = 0xA1, '4085703930'
*Mar  4 19:43:00.404: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0x800E
*Mar  4 19:43:00.408:         Channel ID i = 0xA98393
*Mar  4 19:43:00.416: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0x800E
*Mar  4 19:43:00.416:         Channel ID i = 0xA98393
*Mar  4 19:43:00.488: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x0E
*Mar  4 19:43:00.720: Se0:18 PPP: Treating connection as a callin
*Mar  4 19:43:00.720: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:43:02.744: Se0:18 PPP: Phase is AUTHENTICATING, by this end
*Mar  4 19:43:02.744: Se0:18 CHAP: O CHALLENGE id 2 len 26 from "STACK"
*Mar  4 19:43:02.776: Se0:18 CHAP: I RESPONSE id 2 len 30 from "timeout"
*Mar  4 19:43:02.776: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:43:02.776: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 
adapter=0 port=0 channel=18
*Mar  4 19:43:02.776: AAA: parse NAME= idb TYPE=-1 tty=-1
*Mar  4 19:43:02.780: RADIUS: ustruct sharecount=1
*Mar  4 19:43:02.780: RADIUS: Initial Transmit Serial0:18 id 5 172.16.24.117:1645, 
Access-Request, len 104
*Mar  4 19:43:02.780:         Attribute 4 6 AC101874
*Mar  4 19:43:02.780:         Attribute 5 6 00004E32
*Mar  4 19:43:02.780:         Attribute 61 6 00000002
*Mar  4 19:43:02.780:         Attribute 1 11 74696D65
*Mar  4 19:43:02.780:         Attribute 30 12 34303835
*Mar  4 19:43:02.780:         Attribute 31 12 34303835
*Mar  4 19:43:02.780:         Attribute 3 19 02AE5572
*Mar  4 19:43:02.780:         Attribute 6 6 00000002
*Mar  4 19:43:02.780:         Attribute 7 6 00000001
*Mar  4 19:43:02.784: RADIUS: Received from id 5 172.16.24.117:1645, Access-Accept, len 50
*Mar  4 19:43:02.784:         Attribute 6 6 00000002
*Mar  4 19:43:02.784:         Attribute 7 6 00000001
*Mar  4 19:43:02.784:         Attribute 8 6 FFFFFFFE
*Mar  4 19:43:02.784:         Attribute 27 6 0000005A
*Mar  4 19:43:02.784:         Attribute 28 6 0000003C
*Mar  4 19:43:02.788: Se0:18 AAA/AUTHOR/LCP: Authorize LCP
*Mar  4 19:43:02.788: AAA/AUTHOR/LCP Se0:18 (900316608): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:43:02.788: AAA/AUTHOR/LCP: Se0:18 (900316608) send AV service=ppp
*Mar  4 19:43:02.788: AAA/AUTHOR/LCP: Se0:18 (900316608) send AV protocol=lcp
*Mar  4 19:43:02.788: AAA/AUTHOR/LCP (900316608) found list "default"
*Mar  4 19:43:02.788: AAA/AUTHOR/LCP: Se0:18 (900316608) METHOD=RADIUS
*Mar  4 19:43:02.788: AAA/AUTHOR (900316608): Post authorization status = PASS_REPL
*Mar  4 19:43:02.788: Se0:18 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar  4 19:43:02.788: Se0:18 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar  4 19:43:02.788: Se0:18 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar  4 19:43:02.788: Se0:18 CHAP: O SUCCESS id 2 len 4
*Mar  4 19:43:02.788: AAA/ACCT/NET/START User timeout, Port Serial0:18, List ""
*Mar  4 19:43:02.788: AAA/ACCT/NET: Found list "default"
*Mar  4 19:43:02.788: Se0:18 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar  4 19:43:02.788: AAA/AUTHOR/FSM Se0:18 (3608739008): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:43:02.788: AAA/AUTHOR/FSM: Se0:18 (3608739008) send AV service=ppp
*Mar  4 19:43:02.788: AAA/AUTHOR/FSM: Se0:18 (3608739008) send AV protocol=ip
*Mar  4 19:43:02.788: AAA/AUTHOR/FSM (3608739008) found list "default"
*Mar  4 19:43:02.788: AAA/AUTHOR/FSM: Se0:18 (3608739008) METHOD=RADIUS
*Mar  4 19:43:02.788: RADIUS: Using NAS default peer
*Mar  4 19:43:02.788: RADIUS: Authorize IP address 0.0.0.0
*Mar  4 19:43:02.788: AAA/AUTHOR (3608739008): Post authorization status = PASS_REPL
*Mar  4 19:43:02.788: Se0:18 AAA/AUTHOR/FSM: We can start IPCP
*Mar  4 19:43:02.788: Se0:18 AAA/AUTHOR/FSM: (0): Can we start CDPCP?
*Mar  4 19:43:02.792: AAA/AUTHOR/FSM Se0:18 (3955392150): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:43:02.792: AAA/AUTHOR/FSM: Se0:18 (3955392150) send AV service=ppp
*Mar  4 19:43:02.792: AAA/AUTHOR/FSM: Se0:18 (3955392150) send AV protocol=cdp
*Mar  4 19:43:02.792: AAA/AUTHOR/FSM (3955392150) found list "default"
*Mar  4 19:43:02.792: AAA/AUTHOR/FSM: Se0:18 (3955392150) METHOD=RADIUS
*Mar  4 19:43:02.792: AAA/AUTHOR (3955392150): Post authorization status = PASS_REPL
*Mar  4 19:43:02.792: Se0:18 AAA/AUTHOR/FSM: We can start CDPCP
*Mar  4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 0.0.0.0
*Mar  4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar  4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 0.0.0.0
*Mar  4 19:43:02.808: Se0:18 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar  4 19:43:02.808: Se0:18 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar  4 19:43:02.808: Se0:18 AAA/AUTHOR/FSM: Succeeded
*Mar  4 19:43:02.816: Se0:18 AAA/AUTHOR/IPCP: Start.  Her address 10.1.1.3, we want 10.1.1.3
*Mar  4 19:43:02.816: AAA/AUTHOR/IPCP Se0:18 (2267743837): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:43:02.816: AAA/AUTHOR/IPCP: Se0:18 (2267743837) send AV service=ppp
*Mar  4 19:43:02.816: AAA/AUTHOR/IPCP: Se0:18 (2267743837) send AV protocol=ip
*Mar  4 19:43:02.816: AAA/AUTHOR/IPCP: Se0:18 (2267743837) send AV addr*10.1.1.3
*Mar  4 19:43:02.816: AAA/AUTHOR/IPCP (2267743837) found list "default"
*Mar  4 19:43:02.816: AAA/AUTHOR/IPCP: Se0:18 (2267743837) METHOD=RADIUS
*Mar  4 19:43:02.816: RADIUS: Using NAS default peer
*Mar  4 19:43:02.816: RADIUS: Authorize IP address 10.1.1.3
*Mar  4 19:43:02.816: AAA/AUTHOR (2267743837): Post authorization status = PASS_REPL
*Mar  4 19:43:02.816: Se0:18 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:43:02.820: Se0:18 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.3
*Mar  4 19:43:02.820: Se0:18 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:43:02.820: Se0:18 AAA/AUTHOR/IPCP: Done.  Her address 10.1.1.3, 
we want 10.1.1.3
*Mar  4 19:43:02.824: Se0:18 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar  4 19:43:02.824: Se0:18 AAA/PER-USER: processing author params.
access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time
  Se0:18       timeout          PPP           00:00:19  00:00:19  
access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          00:01:30  00:01:00  00:00:37  
access-3#ping 10.1.1.3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms
access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          00:01:30  00:01:00  00:00:57  
access-3#show caller user timeout

  User: timeout, line Se0:18, service PPP
        Active time 00:00:38, Idle time 00:00:10
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:00:51  00:00:49  
  PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP, CDPCP
  Dialer: Connected to 4085551200, inbound
          Idle timer 60 secs, idle 10 secs
          Type is ISDN, group Serial0:23
  IP: Local 10.1.1.1, remote 10.1.1.3
      Access list (I/O) is 199/not set
  Counts: 51 packets input, 2104 bytes, 0 no buffer
          11 input errors, 2 CRC, 3 frame, 0 overrun
          58 packets output, 2233 bytes, 0 underruns
          0 output errors, 0 collisions, 45 interface resets

access-3#show caller user timeout

  User: timeout, line Se0:18, service PPP
        Active time 00:00:45, Idle time 00:00:17
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:00:44  00:00:42  
  PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP, CDPCP
  Dialer: Connected to 4085551200, inbound
          Idle timer 60 secs, idle 17 secs
          Type is ISDN, group Serial0:23
  IP: Local 10.1.1.1, remote 10.1.1.3
      Access list (I/O) is 199/not set
  Counts: 52 packets input, 2120 bytes, 0 no buffer
          11 input errors, 2 CRC, 3 frame, 0 overrun
          59 packets output, 2249 bytes, 0 underruns
          0 output errors, 0 collisions, 45 interface resets

access-3#ping 10.1.1.3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/34/40 ms
access-3#show caller user timeout

  User: timeout, line Se0:18, service PPP
        Active time 00:01:02, Idle time 00:00:04
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:00:27  00:00:55  
  PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP, CDPCP
  Dialer: Connected to 4085551200, inbound
          Idle timer 60 secs, idle 4 secs
          Type is ISDN, group Serial0:23
  IP: Local 10.1.1.1, remote 10.1.1.3
      Access list (I/O) is 199/not set
  Counts: 60 packets input, 2688 bytes, 0 no buffer
          11 input errors, 2 CRC, 3 frame, 0 overrun
          67 packets output, 2817 bytes, 0 underruns
          0 output errors, 0 collisions, 45 interface resets

access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          00:01:30  00:01:00  00:00:21  
access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          00:01:30  00:01:00  00:00:07  
access-3#
*Mar  4 19:44:33.788: ISDN Se0:23: TX ->  DISCONNECT pd = 8  callref = 0x800E
*Mar  4 19:44:33.788:         Cause i = 0x8090 - Normal call clearing 
*Mar  4 19:44:33.840: ISDN Se0:23: RX <-  RELEASE pd = 8  callref = 0x0E
*Mar  4 19:44:33.852: Se0:18 AAA/ACCT: ISDN xmit 64000 recv 64000 hwidb 612048BC
*Mar  4 19:44:33.852: AAA/ACCT/NET/STOP User timeout, Port Serial0:18:
         task_id=14 timezone=PST service=ppp protocol=ip addr=10.1.1.3 disc-cause=5 
disc-cause-ext=1100 pre-bytes-in=101 pre-bytes-out=102 pre-paks-in=5 pre-paks-out=5 
bytes_in=2258 bytes_out=2276 paks_in=38 paks_out=38 pre-session-time=2 elapsed_time=91 
nas-rx-speed=64000 nas-tx-speed=64000 
*Mar  4 19:44:33.852: ISDN Se0:23: TX ->  RELEASE_COMP pd = 8  callref = 0x800E
*Mar  4 19:44:33.856: Se0:18 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar  4 19:44:33.856: Se0:18 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:44:34.060: TAC+: (3492368360): received acct response status = SUCCESS

Appel du canal unique le RNIS de Non-Multilien avec des Profils virtuels

Est ci-dessous le même utilisateur RNIS de canal unique de non-Multilien mais cette fois avec des Profils virtuels activés. Notez que l'interface de vaccess est créée quoique le multilink ne soit pas négocié et nous créons les commandes de configuration d'installer les temporisateurs.

*Mar  4 19:45:00.480: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x0C
*Mar  4 19:45:00.480:         Bearer Capability i = 0x8890
*Mar  4 19:45:00.480:         Channel ID i = 0xA98393
*Mar  4 19:45:00.480:         Calling Party Number i = '!', 0x80, '4085551200'
*Mar  4 19:45:00.480:         Called Party Number i = 0xA1, '4085703930'
*Mar  4 19:45:00.480: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0x800C
*Mar  4 19:45:00.480:         Channel ID i = 0xA98393
*Mar  4 19:45:00.492: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0x800C
*Mar  4 19:45:00.492:         Channel ID i = 0xA98393
*Mar  4 19:45:00.564: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x0C
*Mar  4 19:45:00.804: Se0:18 PPP: Treating connection as a callin
*Mar  4 19:45:00.804: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:45:02.804: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:45:02.828: Se0:18 PPP: Phase is AUTHENTICATING, by this end
*Mar  4 19:45:02.828: Se0:18 CHAP: O CHALLENGE id 3 len 26 from "STACK"
*Mar  4 19:45:02.860: Se0:18 CHAP: I RESPONSE id 3 len 30 from "timeout"
*Mar  4 19:45:02.860: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar  4 19:45:02.860: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 
adapter=0 port=0 channel=18
*Mar  4 19:45:02.860: AAA: parse NAME= idb TYPE=-1 tty=-1
*Mar  4 19:45:02.860: RADIUS: ustruct sharecount=1
*Mar  4 19:45:02.860: RADIUS: Initial Transmit Serial0:18 id 6 172.16.24.117:1645, 
Access-Request, len 104
*Mar  4 19:45:02.860:         Attribute 4 6 AC101874
*Mar  4 19:45:02.860:         Attribute 5 6 00004E32
*Mar  4 19:45:02.860:         Attribute 61 6 00000002
*Mar  4 19:45:02.864:         Attribute 1 11 74696D65
*Mar  4 19:45:02.864:         Attribute 30 12 34303835
*Mar  4 19:45:02.864:         Attribute 31 12 34303835
*Mar  4 19:45:02.864:         Attribute 3 19 03D4E134
*Mar  4 19:45:02.864:         Attribute 6 6 00000002
*Mar  4 19:45:02.864:         Attribute 7 6 00000001
*Mar  4 19:45:02.868: RADIUS: Received from id 6 172.16.24.117:1645, Access-Accept, len 50
*Mar  4 19:45:02.868:         Attribute 6 6 00000002
*Mar  4 19:45:02.868:         Attribute 7 6 00000001
*Mar  4 19:45:02.868:         Attribute 8 6 FFFFFFFE
*Mar  4 19:45:02.868:         Attribute 27 6 0000005A
*Mar  4 19:45:02.868:         Attribute 28 6 0000003C
*Mar  4 19:45:02.868: Se0:18 AAA/AUTHOR/LCP: Authorize LCP
*Mar  4 19:45:02.868: AAA/AUTHOR/LCP Se0:18 (2825271150): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:45:02.868: AAA/AUTHOR/LCP: Se0:18 (2825271150) send AV service=ppp
*Mar  4 19:45:02.868: AAA/AUTHOR/LCP: Se0:18 (2825271150) send AV protocol=lcp
*Mar  4 19:45:02.868: AAA/AUTHOR/LCP (2825271150) found list "default"
*Mar  4 19:45:02.868: AAA/AUTHOR/LCP: Se0:18 (2825271150) METHOD=RADIUS
*Mar  4 19:45:02.872: AAA/AUTHOR (2825271150): Post authorization status = PASS_REPL
*Mar  4 19:45:02.872: Se0:18 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar  4 19:45:02.872: Se0:18 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar  4 19:45:02.872: Se0:18 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar  4 19:45:02.872: AAA/AUTHOR/LCP Se0:18: Per-user interface config created:
timeout absolute 1 30
ppp timeout idle 60

*Mar  4 19:45:02.872: Se0:18 CHAP: O SUCCESS id 3 len 4
*Mar  4 19:45:02.872: AAA/ACCT/NET/START User timeout, Port Serial0:18, List ""
*Mar  4 19:45:02.872: AAA/ACCT/NET: Found list "default"
*Mar  4 19:45:02.872: Vi1 VTEMPLATE: Reuse Vi1, recycle queue size 0
*Mar  4 19:45:02.872: Vi1 VTEMPLATE: Hardware address 00e0.1e81.636c
*Mar  4 19:45:02.872: Vi1 VTEMPLATE: Has a new cloneblk vtemplate, now it has vtemplate
*Mar  4 19:45:02.872: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar  4 19:45:02.872: Vi1 VTEMPLATE: Clone from Virtual-Template1
interface Virtual-Access1
default ip address
no ip address
encap ppp
ip unnumbered Loopback0
ip access-group 199 in
ip helper-address 172.16.24.118
no ip directed-broadcast
ip accounting output-packets
ip nat inside
no keepalive
peer default ip address pool default
compress mppc
ppp callback accept
ppp authentication chap pap ms-chap
ppp multilink
multilink max-links 2
end

  enabling payload compression on this interface.
*Mar  4 19:45:02.952: Vi1 VTEMPLATE: Has a new cloneblk AAA, now it has vtemplate/AAA
*Mar  4 19:45:02.952: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar  4 19:45:02.952: Vi1 VTEMPLATE: Clone from AAA
interface Virtual-Access1
timeout absolute 1 30
ppp timeout idle 60
end

*Mar  4 19:45:02.976: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
*Mar  4 19:45:02.976: Vi1 PPP: Treating connection as a dedicated line
*Mar  4 19:45:02.976: Vi1 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar  4 19:45:02.980: Vi1 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar  4 19:45:02.980: AAA/AUTHOR/FSM Vi1 (2657898442): Port='Serial0:18' list='' service=NET
*Mar  4 19:45:02.980: AAA/AUTHOR/FSM: Vi1 (2657898442) send AV service=ppp
*Mar  4 19:45:02.980: AAA/AUTHOR/FSM: Vi1 (2657898442) send AV protocol=ip
*Mar  4 19:45:02.980: AAA/AUTHOR/FSM (2657898442) found list "default"
*Mar  4 19:45:02.980: AAA/AUTHOR/FSM: Vi1 (2657898442) METHOD=RADIUS
*Mar  4 19:45:02.980: RADIUS: Using NAS default peer
*Mar  4 19:45:02.980: RADIUS: Authorize IP address 0.0.0.0
*Mar  4 19:45:02.980: AAA/AUTHOR (2657898442): Post authorization status = PASS_REPL
*Mar  4 19:45:02.980: Vi1 AAA/AUTHOR/FSM: We can start IPCP
*Mar  4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 0.0.0.0, we want 0.0.0.0
*Mar  4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar  4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 0.0.0.0, we want 0.0.0.0
*Mar  4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Start.  Her address 10.1.1.3, we want 10.1.1.3
*Mar  4 19:45:02.996: AAA/AUTHOR/IPCP Vi1 (1804338759): Port='Serial0:18' list='' 
service=NET
*Mar  4 19:45:02.996: AAA/AUTHOR/IPCP: Vi1 (1804338759) send AV service=ppp
*Mar  4 19:45:02.996: AAA/AUTHOR/IPCP: Vi1 (1804338759) send AV protocol=ip
*Mar  4 19:45:02.996: AAA/AUTHOR/IPCP: Vi1 (1804338759) send AV addr*10.1.1.3
*Mar  4 19:45:02.996: AAA/AUTHOR/IPCP (1804338759) found list "default"
*Mar  4 19:45:02.996: AAA/AUTHOR/IPCP: Vi1 (1804338759) METHOD=RADIUS
*Mar  4 19:45:02.996: RADIUS: Using NAS default peer
*Mar  4 19:45:02.996: RADIUS: Authorize IP address 10.1.1.3
*Mar  4 19:45:02.996: AAA/AUTHOR (1804338759): Post authorization status = PASS_REPL
*Mar  4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar  4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.3
*Mar  4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar  4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Done.  Her address 10.1.1.3, we want 10.1.1.3
*Mar  4 19:45:03.004: Vi1 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar  4 19:45:03.004: Vi1 AAA/PER-USER: processing author params.
*Mar  4 19:45:03.996: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, 
changed state to up
access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time

  Se0:18       timeout          PPP           00:00:11  00:00:10  
  Vi1          timeout          PPP   VDP     00:00:11  00:00:10  
access-3#show caller timeout

  User: timeout, line Se0:18, service PPP
        Active time 00:00:15, Idle time 00:00:15
  Timeouts:            Absolute  Idle
      Limits:          -         -         
      Disconnect in:   -         -         
  PPP: LCP Open, multilink Closed, CHAP (<- AAA)
  Dialer: Connected to 4085551200, inbound
          Idle timer 60 secs, idle 15 secs
          Type is ISDN, group Serial0:23
  IP: Local 10.1.1.1
      Access list (I/O) is 199/not set
  Counts: 81 packets input, 3291 bytes, 0 no buffer
          11 input errors, 2 CRC, 3 frame, 0 overrun
          87 packets output, 3419 bytes, 0 underruns
          0 output errors, 0 collisions, 47 interface resets

  User: timeout, line Vi1, service PPP VDP
        Active time 00:00:15, Idle time 00:00:15
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:01:13  00:00:44  
  PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP
       Idle timer 60 secs, idle 15 secs
  IP: Local 10.1.1.1, remote 10.1.1.3
      Access list (I/O) is 199/not set
  Counts: 7 packets input, 370 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          19 packets output, 404 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

access-3#show caller timeouts
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:40  
access-3#ping 10.1.1.3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms
access-3#show caller timeouts
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:58  
access-3#show caller user timeout

  User: timeout, line Se0:18, service PPP
        Active time 00:00:34, Idle time 00:00:09
  Timeouts:            Absolute  Idle
      Limits:          -         -         
      Disconnect in:   -         -         
  PPP: LCP Open, multilink Closed, CHAP (<- AAA)
  Dialer: Connected to 4085551200, inbound
          Idle timer 60 secs, idle 9 secs
          Type is ISDN, group Serial0:23
  IP: Local 10.1.1.1
      Access list (I/O) is 199/not set
  Counts: 88 packets input, 3843 bytes, 0 no buffer
          11 input errors, 2 CRC, 3 frame, 0 overrun
          94 packets output, 3971 bytes, 0 underruns
          0 output errors, 0 collisions, 47 interface resets

  User: timeout, line Vi1, service PPP VDP
        Active time 00:00:34, Idle time 00:00:09
  Timeouts:            Absolute  Idle
      Limits:          00:01:30  00:01:00  
      Disconnect in:   00:00:54  00:00:50  

  PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP
       Idle timer 60 secs, idle 9 secs
  IP: Local 10.1.1.1, remote 10.1.1.3
      Access list (I/O) is 199/not set
  Counts: 14 packets input, 922 bytes, 0 no buffer
          0 input errors, 0 CRC, 0 frame, 0 overrun
          33 packets output, 956 bytes, 0 underruns
          0 output errors, 0 collisions, 0 interface resets

access-3#show caller timeout
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:42  
access-3#show caller timeouts
                                  Session   Idle      Disconnect
  Line         User               Timeout   Timeout   User in
  Se0:18       timeout          -         -         -         
  Vi1          timeout          00:01:30  00:01:00  00:00:22  
access-3#show caller
                                                Active    Idle
  Line         User               Service       Time      Time
  Se0:18       timeout          PPP           00:01:22  00:00:57  
  Vi1          timeout          PPP   VDP     00:01:22  00:00:57  
access-3#
*Mar  4 19:46:28.996: Vi1 PPP: Idle timeout, dropping connection
*Mar  4 19:46:28.996: Se0:18 AAA/ACCT: ISDN xmit 64000 recv 64000 hwidb 612048BC
*Mar  4 19:46:28.996: AAA/ACCT/NET/STOP User timeout, Port Serial0:18:
         task_id=15 timezone=PST service=ppp protocol=ip addr=10.1.1.3 disc-cause=4 
disc-cause-ext=1021 pre-bytes-in=101 pre-bytes-out=102 pre-paks-in=5 pre-paks-out=5 
bytes_in=1024 bytes_out=1036 paks_in=21 paks_out=21 pre-session-time=2 elapsed_time=86 
nas-rx-speed=64000 nas-tx-speed=64000 
*Mar  4 19:46:29.000: ISDN Se0:23: TX ->  DISCONNECT pd = 8  callref = 0x800C
*Mar  4 19:46:29.000:         Cause i = 0x8090 - Normal call clearing 
*Mar  4 19:46:29.000: Vi1 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar  4 19:46:29.000: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
*Mar  4 19:46:29.004: Vi1 VTEMPLATE: Free vaccess
*Mar  4 19:46:29.004: Vi1 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:46:29.052: ISDN Se0:23: RX <-  RELEASE pd = 8  callref = 0x0C
*Mar  4 19:46:29.064: ISDN Se0:23: TX ->  RELEASE_COMP pd = 8  callref = 0x800C
*Mar  4 19:46:29.064: Se0:18 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar  4 19:46:29.208: TAC+: (3109010012): received acct response status = SUCCESS
*Mar  4 19:46:29.580: VTEMPLATE: Clean up dirty vaccess queue, size 1
*Mar  4 19:46:29.580: Vi1 VTEMPLATE: Found a dirty vaccess clone with vtemplate/AAA
*Mar  4 19:46:29.580: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar  4 19:46:29.580: Vi1 VTEMPLATE: Unclone to-be-freed command#2
interface Virtual-Access1
default ppp timeout idle 60
default timeout absolute 1 30
end

*Mar  4 19:46:29.596: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar  4 19:46:29.616: Vi1 VTEMPLATE: Remove cloneblk AAA with vtemplate/AAA
*Mar  4 19:46:29.616: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar  4 19:46:29.616: Vi1 VTEMPLATE: Unclone to-be-freed command#15
interface Virtual-Access1
default multilink max-links 2
default ppp multilink
default ppp authentication chap pap ms-chap
default ppp callback accept
default compress mppc
default peer default ip address pool default
default keepalive
default ip nat inside
default ip accounting output-packets
default ip directed-broadcast
default ip helper-address 172.16.24.118
default ip access-group 199 in
default ip unnumbered Loopback0
default encap ppp
default ip address
end

*Mar  4 19:46:29.704: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar  4 19:46:29.720: Vi1 VTEMPLATE: Remove cloneblk vtemplate with vtemplate/AAA
*Mar  4 19:46:29.720: Vi1 VTEMPLATE: Add vaccess to recycle queue, queue SIZE=1
*Mar  4 19:46:30.000: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, 
changed state to down

Conversations connexes de la communauté de soutien de Cisco

Le site Cisco Support Community est un forum où vous pouvez poser des questions, répondre à des questions, faire part de suggestions et collaborer avec vos pairs.


Informations connexes


Document ID: 10236