Switches : Switches Cisco Catalyst 6500 Series

Substitua um módulo falhado do supervisor redundante nos Catalyst 6500 Series Switch que executam Cactos (o híbrido)

14 Outubro 2016 - Tradução por Computador
Outras Versões: Versão em PDFpdf | Inglês (22 Agosto 2015) | Feedback


Índice


Introdução

Este documento mostra como substituir um módulo falhado do supervisor redundante nos Catalyst 6500 Series Switches. Este documento explica o procedimento para os módulos do supervisor que são executado no Hybrid OS.

Pré-requisitos

Requisitos

A Cisco recomenda que você tenha conhecimento destes tópicos:

Componentes Utilizados

As informações neste documento são baseadas nestas versões de software e hardware:

  • Cisco Catalyst 6500 Series Switch

  • Módulo do supervisor: WS-SUP32-GE-3B

  • Hybrid OS:

    • OS do catalizador (Cactos) 8.5(8)

    • ½ 12.2(18)SXF7 DO ¿  MSFC IOSïÂ

As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. Todos os dispositivos utilizados neste documento foram iniciados com uma configuração (padrão) inicial. Se a sua rede estiver ativa, certifique-se de que entende o impacto potencial de qualquer comando.

Produtos Relacionados

Este documento pode igualmente ser usado com estes versão de hardware e software:

  • Supervisor 720 que executa o Hybrid OS

  • Supervisor 2 que executa o Hybrid OS

Convenções

Consulte as Convenções de Dicas Técnicas da Cisco para obter mais informações sobre convenções de documentos.

Informações de Apoio

Estes são alguns dos pontos importantes relativos aos módulos do supervisor redundante:

  • No motor do supervisor em standby, a porta de Console é inativa, o status de módulo mostra como o “apoio”, e o estado para as portas de uplink é mostrado normalmente.

  • A fim permitir que você controle o booting de cada Supervisor Engine separadamente, os registros de configuração não são sincronizados entre os motores do supervisor.

  • Se as versões de software dos dois motores do supervisor são diferentes, ou se a configuração de NVRAM dos dois motores do supervisor é diferente, o motor do supervisor ativo transfere automaticamente suas imagem do software e configuração ao motor do supervisor em standby.

  • Os motores do supervisor usam duas imagens flash: a imagem de boot e a imagem de tempo de execução. O nome de arquivo da imagem de boot, que é especificado no variável de ambiente da BOTA, é armazenado no NVRAM. A imagem de tempo de execução é a imagem de boot que o monitor de ROM se usa para carreg o Supervisor Engine. Após as inicializações de sistema, a imagem de tempo de execução reside no ram dinâmica (DRAM).

  • Os Engine de Redundant Supervisor devem ser do mesmo tipo com a mesma placa de recurso modelo. O WS-X6K-SUP1-2GE e o WS-X6K-SUP1A-2GE, que são ambos sem cartões de recursos de política (PFC), são compatíveis para a Redundância. Para os motores do supervisor com PFC, os PFC devem ser idênticos para a Redundância (dois PFC, dois PFC2, dois PFC3A, dois PFC3B, ou dois PFC3BXL).

Procedimento passo a passo para substituir o módulo do supervisor - O mesmo Hybrid OS

Esta seção fornece o procedimento passo a passo para substituir o módulo do supervisor 32 em um Catalyst 6500 Series Switch. Este exemplo usa um Cisco Catalyst 6509 Switch, que tenha dois módulos do supervisor no entalhe 5 e 6. O módulo do supervisor no entalhe 6 falhou. Supõe-se que o módulo do supervisor falhado no entalhe 6 está removido do chassi. Você pode ver o procedimento para adicionar o módulo do supervisor novo no entalhe 6.

Se você tem um Cisco Catalyst 6500 Series Switch adicional, você pode conectar o supervisor novo no interruptor e promover ou degradar o Hybrid OS ao mesmo nível que o supervisor no entalhe 5 do switch de produção. Se você tem o mesmo Hybrid OS no módulo do supervisor novo, você não precisa de configurar qualquer coisa no módulo do supervisor novo. Quando você adicionar o módulo do supervisor no entalhe 6, do supervisor ativo do motor os synchs automaticamente a configuração. Esta seção mostra o processo passo a passo e a lista de verificação durante a substituição do supervisor.

Este é o procedimento passo a passo para substituir o módulo do supervisor 32 em um Catalyst 6500 Series Switch:

  1. Adicionar o módulo do supervisor no entalhe 6.

    Se você tem a conexão de console ao supervisor no entalhe 6, você deve ver esta saída:

    
    !--- Supervisor module at slot 6
    
    System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2004 by cisco Systems, Inc.
    Cat6k-Sup32 platform with 524288 Kbytes of main memory
    
    Autoboot executing command: "boot bootdisk:cat6000-sup32pfc3k8.8-5-8.bin"
    Self decompressing the image : ############################################
    ###########################################################################
    ###########################################################################
    ###########################################################################
    ###########################################################################
    ###########################################################################
    ###########################################################################
    ###########################################################################
    ###########################################################################
    ###########################################################################
    ###########################################################################
    ##################################################### [OK]
    
    
    System Power On Diagnostics
    DRAM Size ..........................512 MB
    Testing DRAM .......................Passed
    Verifying Text Segment .............Passed
    NVRAM Size .........................2048 KB
    Level2 Cache .......................Present
    Level3 Cache .......................Absent
    System Power On Diagnostics Complete
    
    Currently running ROMMON from S (Gold) region
    Boot image: bootdisk:cat6000-sup32pfc3k8.8-5-8.bin
    
    
    Firmware compiled 01-Dec-06 12:57 by integ Build [100]
    
    
    This module is now in standby mode.
    Console is disabled for standby supervisor.
    

    Esta saída mostra o console do supervisor ativo no entalhe 5:

    Access2> (enable)
    Access2> (enable)
    Access2> (enable) 2007 May 22 19:17:48 %SYS-5-MOD_INSERT:Module 
    6 has been inserted
    
    Access2> (enable)
    Access2> (enable)
    Access2> (enable) 
    %SYS-5-SUP_MODSBY:Module 6 is in standby mode
    
    %SYS-5-SUP_IMGSYNC:File synchronization process will start in 120 seconds
    
    %DIAG-6-RUN_MINIMUM:Module 6: Running Minimal Diagnostics...
    
    %DIAG-6-DIAG_OK:Module 6: Passed Online Diagnostics
    
    %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/1 is not supported
    
    %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/2 is not supported
    
    %SYS-5-PORT_SSUPOK:Ports on standby supervisor (module 6) are up
    
    %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 6
    
    %DIAG-6-RUN_MINIMUM:Module 16: Running Minimal Diagnostics...
    
    %DIAG-6-DIAG_OK:Module 16: Passed Online Diagnostics
    
    %SYS-5-MOD_OK:Module 16(WS-F6K-MSFC2A,SAL1018LQ3C) is online
    
    %MGMT-5-SYS_CONFIG_START_MOD_FAIL:Unable to start system configuration 
    for module 6
    
    %MGMT-5-SYS_CONFIG_START_MOD_FAIL:Unable to start system configuration for 
    module 16
    
    %SYS-5-SUP_IMGSYNCSTART:Active supervisor is synchronizing bootdisk:
    cat6000-sup32pfc3k8.8-5-8.bin
    
    %SYS-5-SUP_IMGSYNCFINISH:Active supervisor has synchronized bootdisk:
    cat6000-sup32pfc3k8.8-5-8.bin
    
    Access2> (enable)
  2. Verifique o estado da redundância de supervisor:

    Access2> (enable) show system highavailability
    Highavailability: enabled
    Highavailability versioning: disabled
    Highavailability Operational-status: ON
    Access2> (enable)
  3. Verifique o estado da redundância de MSFC:

    Access2> (enable) session 15
    Trying Router-15...
    Connected to Router-15.
    Escape character is '^]'.
    
    LAB-Router>enable
    LAB-Router#show redundancy
    Redundant System Information :
    ------------------------------
           Available system uptime = 10 minutes
    Switchovers system experienced = 0
                  Standby failures = 0
            Last switchover reason = unsupported
    
                     Hardware Mode = Duplex
        Configured Redundancy Mode = Stateful SwitchOver - SSO
         Operating Redundancy Mode = Stateful SwitchOver - SSO
                  Maintenance Mode = Disabled
                    Communications = Up
    
    Current Processor Information :
    -------------------------------
                   Active Location = slot 5
            Current Software state = ACTIVE
           Uptime in current state = 10 minutes
                     Image Version = Cisco Internetwork Operating System Software
    IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), 
    Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by cisco Systems, Inc.
    Compiled Thu 23-Nov-06 01:03 by kellythw
                              BOOT =
                       CONFIG_FILE =
                           BOOTLDR =
            Configuration register = 0x2102
    
    Peer Processor Information :
    ----------------------------
                  Standby Location = slot 6
            Current Software state = STANDBY HOT
           Uptime in current state = 2 minutes
                     Image Version = Cisco Internetwork Operating System Software
    IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), 
    Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by cisco Systems, Inc.
    Compiled Thu 23-Nov-06 01:03 by kellythw
                              BOOT =
                       CONFIG_FILE =
                           BOOTLDR =
            Configuration register = 0x2102
    
    
    LAB-Router#
  4. Force o failover de supervisor e teste-o:

    
    !--- Supervisor in slot 5
    
    Access2> (enable) switch supervisor
    This command will force a switch-over to the standby Supervisor module.
    Do you want to continue (y/n) [n]? y
    2007 May 21 20:40:37 %SYS-5-MOD_RESET:Module 5 reset from Console//
    Access2> (enable)
    System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2004 by cisco Systems, Inc.
    Cat6k-Sup32 platform with 262144 Kbytes of main memory
    
    Autoboot executing command: "boot bootdisk:cat6000-sup32pfc3k8.8-5-8.bin"
    Self decompressing the image : ##############################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    ##################################################### [OK]
    
    
    System Power On Diagnostics
    DRAM Size ..........................256 MB
    Testing DRAM .......................Passed
    Verifying Text Segment .............Passed
    NVRAM Size .........................2048 KB
    Level2 Cache .......................Present
    Level3 Cache .......................Absent
    System Power On Diagnostics Complete
    
    Currently running ROMMON from S (Gold) region
    Boot image: bootdisk:cat6000-sup32pfc3k8.8-5-8.bin
    
    
    Firmware compiled 01-Dec-06 12:57 by integ Build [100]
    
    This module is now in standby mode.
    Console is disabled for standby supervisor
    
  5. O console no supervisor 6 e verifica o supervisor e a configuração de MSFC.

Procedimento passo a passo para substituir o módulo do supervisor - Hybrid OS diferente

Esta seção explica o procedimento passo a passo para substituir o módulo do supervisor 32 em um Catalyst 6500 Series Switch. Este exemplo usa um Cisco Catalyst 6509 Switch que tenha dois módulos do supervisor no entalhe 5 e 6. O módulo do supervisor no entalhe 6 falhou. Supõe-se que o módulo do supervisor falhado no entalhe 6 está removido do chassi. Você pode ver o procedimento para adicionar o módulo do supervisor novo no entalhe 6.

Se você não tem uma opção para promover o Hybrid OS novo do supervisor à mesma versão que o supervisor ativo, você pode executar este procedimento para adicionar o módulo do supervisor e para sincronizar o Hybrid OS e a configuração de switch. A maioria do procedimento é automatizado. Este documento mostra o processo passo a passo e a lista de verificação a ser executados durante a substituição do supervisor.

Verifique antes que você adicione o módulo do supervisor novo

Esta seção mostra-lhe a saída da mostra do interruptor sem o supervisor no entalhe 6.

  1. Módulo show output:

    Access2> (enable) show module
    Mod Slot Ports Module-Type               Model               Sub Status
    --- ---- ----- ------------------------- ------------------- --- --------
    1   1    0     1000BaseX Ethernet                            no  power-down
    2   2    48    10/100BaseTX Ethernet     WS-X6248-RJ-45      no  ok
    3   3    48    10/100BaseTX Ethernet     WS-X6348-RJ-45      yes ok
    4   4    48    10/100BaseTX Ethernet     WS-X6348-RJ-45      yes ok
    5   5    9     1000BaseX Supervisor      WS-SUP32-GE-3B      yes ok
    15  5    1     Multilayer Switch Feature WS-F6K-MSFC2A       no  ok
    7   7    5     Communication Media Mod.  WS-SVC-CMM          no  ok
    8   8    0     FXS                                           no  power-down
    9   9    0     10/100BaseTX Ethernet                         no  power-down
    
    
    !--- Output suppressed
    
    
    Mod Sub-Type                Sub-Model           Sub-Serial  Sub-Hw Sub-Sw
    --- ----------------------- ------------------- ----------- ------ ------
    3   Inline Power Module     WS-F6K-VPWR                     1.0    1.1(1)
    4   Inline Power Module     WS-F6K-VPWR                     1.0    1.1(1)
    5   L3 Switching Engine III WS-F6K-PFC3B        SAL1012GREU 2.1
    Access2> (enable)
  2. Saídas de versão da mostra:

    Access2> (enable) show version
    WS-C6509 Software, Version NmpSW: 8.5(8)
    Copyright (c) 1995-2006 by Cisco Systems
    NMP S/W compiled on Dec  1 2006, 23:03:43
    
    System Bootstrap Version: 12.2
    System Boot Image File is 'bootdisk:cat6000-sup32pfc3k8.8-5-8.bin'
    System Configuration register is 0x2102
    
    Hardware Version: 2.0  Model: WS-C6509  Serial #: SCA034500F5
    
    PS1  Module: WS-CAC-6000W    Serial #: AZS10130G7T
    
    Mod Port Model               Serial #    Versions
    --- ---- ------------------- ----------- --------------------------------------
    2   48   WS-X6248-RJ-45      SAD03431007 Hw : 1.1
                                             Fw : 4.2(0.24)VAI78
                                             Sw : 8.5(8)
    3   48   WS-X6348-RJ-45      SAD04150A2T Hw : 1.1
                                             Fw : 5.3(1)
                                             Sw : 8.5(8)
             WS-F6K-VPWR                     Hw : 1.0
                                             Sw : 1.1(1)
    4   48   WS-X6348-RJ-45      SAD05070CNX Hw : 2.0
                                             Fw : 5.4(2)
                                             Sw : 8.5(8)
             WS-F6K-VPWR                     Hw : 1.0
                                             Sw : 1.1(1)
    5   9    WS-SUP32-GE-3B      SAL1010F8KG Hw : 4.2
                                             Fw : 12.2
                                             Fw1: 8.5(8)
                                             Sw : 8.5(8)
                                             Sw1: 8.5(8)
             WS-F6K-PFC3B        SAL1012GREU Hw : 2.1
                                             Sw :
    7   5    WS-SVC-CMM          SAD100707YJ Hw : 2.8
                                             Fw : 12.4(7a),
                                             Sw : 12.4(7a),
    15  1    WS-F6K-MSFC2A       SAL1012GG1X Hw : 3.0
                                             Fw : 12.2(18)SXF7
                                             Sw : 12.2(18)SXF7
    
           DRAM                    FLASH                   NVRAM
    Module Total   Used    Free    Total   Used    Free    Total Used  Free
    ------ ------- ------- ------- ------- ------- ------- ----- ----- -----
    5      262144K 124421K 137723K 249772K   9796K 239976K 2048K  366K 1682K
    
    Uptime is 0 day, 0 hour, 3 minutes
    Access2> (enable)
  3. Variável de inicialização:

    
    !--- Current working directory
    
    Access2> (enable) pwd
    bootdisk
    
    
    !--- Files in the bootdisk
    
    Access2> (enable) dir
          2   -rw-  10029260    Dec 13 2006 15:37:08 cat6000-sup32pfc3k8.8-5-8.bin
    
    245735424 bytes available (10031104 bytes used)
    
    
    !--- Boot variable
    
    Access2> (enable) show boot
    BOOT variable = bootdisk:cat6000-sup32pfc3k8.8-5-8.bin,1;
    CONFIG_FILE variable = bootflash:switch.cfg
    
    Configuration register is 0x2102
    ignore-config: disabled
    auto-config: non-recurring, overwrite, sync disabled
    ROMMON console baud: 9600
    boot: image specified by the boot system commands
    
    Image auto sync is enabled
    Image auto sync timer is 120 seconds
    Access2> (enable)

Adicionar o módulo do supervisor novo

O módulo do supervisor é introduzido no entalhe 6. As saídas do console dos módulos do active e do supervisor em standby quando você adiciona o módulo novo do supervisor em standby no interruptor são mostradas aqui:

  1. Introduza o módulo do supervisor novo no entalhe 6.

    Você pode ver este mensagem de registro no módulo de supervisor ativo:

    Access2> (enable) 2007 May 21 20:21:14 %SYS-5-MOD_INSERT:Module 6 has been 
    inserted

    Se você consolou no supervisor em standby em 6, você pode ver este processo de boot:

    System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2004 by cisco Systems, Inc.
    Cat6k-Sup32 platform with 524288 Kbytes of main memory
    
    Autoboot executing command: "boot bootdisk:cat6000-sup32pfc3k8.8-4-5.bin"
    Self decompressing the image : ##############################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    #############################################################################
    ######################################################################## [OK]
    
    
    System Power On Diagnostics
    DRAM Size ..........................512 MB
    Testing DRAM .......................Passed
    Verifying Text Segment .............Passed
    NVRAM Size .........................2048 KB
    Level2 Cache .......................Present
    Level3 Cache .......................Absent
    System Power On Diagnostics Complete
    
    Currently running ROMMON from S (Gold) region
    Boot image: bootdisk:cat6000-sup32pfc3k8.8-4-5.bin
    
    
    Firmware compiled 02-Aug-05 16:08 by integ Build [100]
    
    
    This module is now in standby mode.
    Console is disabled for standby supervisor
    
  2. Você pode verificar o status de redundância do módulo de supervisor ativo no entalhe 5.

    Access2> (enable) 2007 May 21 20:23:09 %SYS-5-SUP_MODSBY:Module 6 is in standby
    mode
    2007 May 21 20:23:11 %SYS-5-SUP_IMGSYNCSTART:Active supervisor is synchronizing
    bootdisk:cat6000-sup32pfc3k8.8-5-8.bin
    
    Access2> (enable) show system highavailability
    Highavailability: enabled
    Highavailability versioning: disabled
    Highavailability Operational-status: OFF(standby-supervisor-image-incompatible)
    

    O módulo de supervisor ativo copia o Cactos no módulo do supervisor em standby. Igualmente configura o variável de inicialização do motor do supervisor em standby ao Cactos novo.

    Access2> (enable)
    2007 May 21 20:24:23 %SYS-5-SUP_IMGSYNCFINISH:Active superviso
    r has synchronized bootdisk:cat6000-sup32pfc3k8.8-5-8.bin

    Depois que a imagem de cactos é copiada ao supervisor em standby, os reloads do módulo em standby 6 automaticamente com a imagem nova.

    This module is now in standby mode.
    Console is disabled for standby supervisor
    
    System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2004 by cisco Systems, Inc.
    Cat6k-Sup32 platform with 524288 Kbytes of main memory
    
    Autoboot executing command: "boot bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin"
    Self decompressing the image : #################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ##################################################### [OK]
    
    
    System Power On Diagnostics
    DRAM Size ..........................512 MB
    Testing DRAM .......................Passed
    Verifying Text Segment .............Passed
    NVRAM Size .........................2048 KB
    Level2 Cache .......................Present
    Level3 Cache .......................Absent
    System Power On Diagnostics Complete
    
    Currently running ROMMON from S (Gold) region
    Boot image: bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin
    
    
    Firmware compiled 01-Dec-06 12:57 by integ Build [100]
    
    This module is now in standby mode.
    Console is disabled for standby supervisor
  3. Uma vez que o módulo em standby está acima, você pode verificar o status de redundância do módulo de supervisor ativo.

    Access2> (enable) 2007 May 21 20:26:22 %SYS-5-SUP_MODSBY:Module 6 is in standby
    mode
    2007 May 21 20:26:23 %SYS-5-SUP_IMGSYNC:File synchronization process will start
    in 120 seconds
    2007 May 21 20:27:08 %SYS-1-SYS_LCPERR1:Module 16: RP requested reset of peer RP
    : MSFC on module 16 will be reset
    2007 May 21 20:27:24 %DIAG-6-RUN_MINIMUM:Module 6: Running Minimal Diagnostics..
    .
    2007 May 21 20:27:24 %DIAG-6-DIAG_OK:Module 6: Passed Online Diagnostics
    2007 May 21 20:27:25 %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/1 is not
    supported
    2007 May 21 20:27:25 %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/2 is not
    supported
    2007 May 21 20:27:25 %SYS-5-PORT_SSUPOK:Ports on standby supervisor (module 6) a
    re up
    2007 May 21 20:27:25 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module
     6
    2007 May 21 20:28:24 %SYS-5-SUP_IMGSYNCSTART:Active supervisor
     is synchronizing bootdisk:cat6000-sup32pfc3k8.8-5-8.bin
    2007 May 21 20:28:25 %SYS-5-SUP_IMGSYNCFINISH:Active supervisor has synchronized
     bootdisk:cat6000-sup32pfc3k8.8-5-8.bin
    
    Access2> (enable)
    Access2> (enable) dir
          2   -rw-  10029260    Dec 13 2006 15:37:08 cat6000-sup32pfc3k8.8-5-8.bin
    
    245735424 bytes available (10031104 bytes used)
    Access2> (enable) dir 6/
          2   -rw-   9356096    May 11 2006 19:04:09 cat6000-sup32pfc3k8.8-4-5.bin
       2287   -rw-  10029260    May 21 2007 20:24:10 RTSYNC_cat6000-sup32pfc3k8.8-5-
    8.bin
    
    !--- You can see the copied CatOS name starts with RTSYNC_
    
    236900352 bytes available (19390464 bytes used)
    
    Access2> (enable) show system highavailability
    Highavailability: enabled
    Highavailability versioning: disabled
    Highavailability Operational-status: ON
    

Verifique o módulo do supervisor depois que você adiciona o módulo do supervisor novo

Execute estas etapas:

  1. Módulo show output:

    Access2> (enable) show module
    Mod Slot Ports Module-Type               Model               Sub Status
    --- ---- ----- ------------------------- ------------------- --- --------
    1   1    0     1000BaseX Ethernet                            no  power-down
    2   2    48    10/100BaseTX Ethernet     WS-X6248-RJ-45      no  ok
    3   3    48    10/100BaseTX Ethernet     WS-X6348-RJ-45      yes ok
    4   4    48    10/100BaseTX Ethernet     WS-X6348-RJ-45      yes ok
    5   5    9     1000BaseX Supervisor      WS-SUP32-GE-3B      yes ok
    15  5    1     Multilayer Switch Feature WS-F6K-MSFC2A       no  ok
    6   6    9     1000BaseX Supervisor      WS-SUP32-GE-3B      yes standby
    7   7    5     Communication Media Mod.  WS-SVC-CMM          no  ok
    8   8    0     FXS                                           no  power-down
    9   9    0     10/100BaseTX Ethernet                         no  power-down
    
    
    !--- Output suppressed
    
    
    Mod Sub-Type                Sub-Model           Sub-Serial  Sub-Hw Sub-Sw
    --- ----------------------- ------------------- ----------- ------ ------
    3   Inline Power Module     WS-F6K-VPWR                     1.0    1.1(1)
    4   Inline Power Module     WS-F6K-VPWR                     1.0    1.1(1)
    5   L3 Switching Engine III WS-F6K-PFC3B        SAL1012GREU 2.1
    6   L3 Switching Engine III WS-F6K-PFC3B        SAL1017L9WJ 2.1
    
  2. Verifique a Redundância-história:

    Access2> (enable) show system redundancy-history
       Maximum entries of switchover history table = 10
       System cold start due to switchover failure = 4
       Standby available time (secs*100)          = 33291
    
       Redundant History Switchover Table:

Verifique o MSFC IO

O Cactos é copiado automaticamente durante o processo da SINCRONIZAÇÃO. Contudo, os IO no MSFC não são copiados automaticamente.

  1. Verifique os IO e a Redundância do MSFC:

    
    !--- 1. Connect to MSFC
    
    Access2> (enable) session 15
    Trying Router-15...
    Connected to Router-15.
    Escape character is '^]'.
    
    LAB-Router>enable
    
    
    !--- 2. Verify the IOS file in the bootflash
    
    LAB-Router#dir
    Directory of bootflash:/
    
        1  -rwx    17966324  Dec 13 2006 15:12:29 +00:00  c6msfc2a-adventerprisek9_w
    an-mz.122-18.SXF7.bin
    
    65536000 bytes total (47569548 bytes free)
    
    
    !--- 3. Show version output
    
    LAB-Router#show version
    Cisco Internetwork Operating System Software
    IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7,
     RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by cisco Systems, Inc.
    Compiled Thu 23-Nov-06 01:03 by kellythw
    Image text-base: 0x40101040, data-base: 0x42638000
    
    ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1)
    BOOTLDR: MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7,
     RELEASE SOFTWARE (fc1)
    
    LAB-Router uptime is 26 minutes
    System returned to ROM by power-on
    System image file is "bootflash:c6msfc2a-adventerprisek9_wan-mz.122-18.SXF7.bin"
    
    
    !--- 4. MSFC redundancy status
    
    LAB-Router#show redundancy
    Redundant System Information :
    ------------------------------
           Available system uptime = 4 minutes
    Switchovers system experienced = 0
                  Standby failures = 0
            Last switchover reason = unsupported
    
                     Hardware Mode = Duplex
        Configured Redundancy Mode = Stateful SwitchOver - SSO
         Operating Redundancy Mode = Route Processor Redundancy
    
    !--- It is running in the RPR mode because the standby MSFC 
    !--- is running different version of IOS.
    
                  Maintenance Mode = Disabled
                    Communications = Up
    
    Current Processor Information :
    -------------------------------
                   Active Location = slot 5
            Current Software state = ACTIVE
           Uptime in current state = 4 minutes
                     Image Version = Cisco Internetwork Operating System Software
    IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), 
    Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by cisco Systems, Inc.
    Compiled Thu 23-Nov-06 01:03 by kellythw
                              BOOT =
                       CONFIG_FILE =
                           BOOTLDR =
            Configuration register = 0x2102
    
    Peer Processor Information :
    ----------------------------
                  Standby Location = slot 6
            Current Software state = STANDBY COLD
           Uptime in current state = 2 minutes
                     Image Version = Cisco Internetwork Operating System Software
    IOS (tm) MSFC2A Software (C6MSFC2A-IPBASE_WAN-M), 
    Version 12.2(18)SXF4, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by cisco Systems, Inc.
    Compiled Thu 23-Mar-06 14:53 by tinhuang
                              BOOT =
                       CONFIG_FILE =
                           BOOTLDR =
            Configuration register = 0x2102
    
    !--- Note that the boot variable is blank. The MSFC boots the 
    !--- first IOS image in the bootflash:
    
    LAB-Router#
    
    LAB-Router#exit
    Access2> (enable)
  2. Promova os IO no MSFC à espera.

    1. Copie a imagem IOS ao MSFC à espera:

      LAB-Router#copy c6msfc2a-adventerprisek9_wan-mz.122-18.SXF7.bin slavebootflash:/
      Destination filename [c6msfc2a-adventerprisek9_wan-mz.122-18.SXF7.bin]?
      Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
      CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
      CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
      CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
      17966324 bytes copied in 44.180 secs (406662 bytes/sec)
      LAB-Router#
      
      
      !--- Delete the old IOS image. Because the boot variable is blank 
      !--- and the MSFC boots the first IOS image in the bootflash:
      
      
      LAB-Router#cd slavebootflash:
      
      LAB-Router#delete c6msfc2a-ipbase_wan-mz.122-18.SXF4.bin
      Delete filename [c6msfc2a-ipbase_wan-mz.122-18.SXF4.bin]?
      Delete slavebootflash:c6msfc2a-ipbase_wan-mz.122-18.SXF4.bin? [confirm]
      LAB-Router#
    2. Recarregue o módulo do supervisor em standby:

      LAB-Router#exit
      
      Access2> (enable) reset 6
      This command will reset module 6.
      Do you want to continue (y/n) [n]? y
      2007 May 21 21:14:03 %SYS-5-MOD_RESET:Module 6 reset from Console//
      Resetting module 6...
      
      
      Access2> (enable) show system highavailability
      Highavailability: enabled
      Highavailability versioning: disabled
      Highavailability Operational-status: OFF(standby-supervisor-not-present)
      Access2> (enable)
      
      2007 May 21 21:16:01 %SYS-5-SUP_MODSBY:Module 6 is in standby
      mode
      2007 May 21 21:16:02 %SYS-5-SUP_IMGSYNC:File synchronization 
      process will start
      in 120 seconds
      2007 May 21 21:16:03 %DIAG-6-RUN_MINIMUM:Module 6: Running Minimal 
      Diagnostics..
      .
      2007 May 21 21:16:05 %DIAG-6-DIAG_OK:Module 6: Passed Online Diagnostics
      2007 May 21 21:16:06 %SYS-3-TRANSCEIVER_NOTSUPP: 
      Transceiver on port 6/1 is not supported
      2007 May 21 21:16:06 %SYS-3-TRANSCEIVER_NOTSUPP: 
      Transceiver on port 6/2 is not supported
      2007 May 21 21:16:06 %SYS-5-PORT_SSUPOK:Ports on standby supervisor 
      (module 6) are up
      2007 May 21 21:16:07 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in 
      sync for Module
       6
      2007 May 21 21:16:49 %SYS-1-SYS_LCPERR1:Module 16: RP requeste
      d reset of peer RP: MSFC on module 16 will be reset
      
      Access2> (enable) show system highavailability
      Highavailability: enabled
      Highavailability versioning: disabled
      Highavailability Operational-status: ON
      Access2> (enable)
  3. Verifique o MSFC IO após a elevação:

    Access2> (enable) session 15
    Trying Router-15...
    Connected to Router-15.
    Escape character is '^]'.
    
    LAB-Router>enable
    
    LAB-Router#show redundancy
    Redundant System Information :
    ------------------------------
           Available system uptime = 17 minutes
    Switchovers system experienced = 0
                  Standby failures = 1
            Last switchover reason = unsupported
    
                     Hardware Mode = Duplex
        Configured Redundancy Mode = Stateful SwitchOver - SSO
         Operating Redundancy Mode = Stateful SwitchOver - SSO
                  Maintenance Mode = Disabled
                    Communications = Up
    
    Current Processor Information :
    -------------------------------
                   Active Location = slot 5
            Current Software state = ACTIVE
           Uptime in current state = 17 minutes
                     Image Version = Cisco Internetwork Operating System Software
    IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), 
    Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by cisco Systems, Inc.
    Compiled Thu 23-Nov-06 01:03 by kellythw
                              BOOT =
                       CONFIG_FILE =
                           BOOTLDR =
            Configuration register = 0x2102
    
    Peer Processor Information :
    ----------------------------
                  Standby Location = slot 6
            Current Software state = STANDBY HOT
           Uptime in current state = 0 minutes
                     Image Version = Cisco Internetwork Operating System Software
    IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), 
    Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by cisco Systems, Inc.
    Compiled Thu 23-Nov-06 01:03 by kellythw
                              BOOT =
                       CONFIG_FILE =
                           BOOTLDR =
            Configuration register = 0x2102
    
    
    LAB-Router#

O Failover ao supervisor em standby e verifica

Agora, você pode Failover o módulo do supervisor ao módulo recentemente adicionado do supervisor em standby e para testá-lo.

  1. Failover o módulo do supervisor:

    Access2> (enable) switch supervisor
    This command will force a switch-over to the standby Supervisor module.
    Do you want to continue (y/n) [n]? y
    2007 May 21 20:40:37 %SYS-5-MOD_RESET:Module 5 reset from Console//
    Access2> (enable)
    System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2004 by cisco Systems, Inc.
    Cat6k-Sup32 platform with 262144 Kbytes of main memory
    
    Autoboot executing command: "boot bootdisk:cat6000-sup32pfc3k8.8-5-8.bin"
    Self decompressing the image : #################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ################################################################################
    ##################################################### [OK]
    
    
    System Power On Diagnostics
    DRAM Size ..........................256 MB
    Testing DRAM .......................Passed
    Verifying Text Segment .............Passed
    NVRAM Size .........................2048 KB
    Level2 Cache .......................Present
    Level3 Cache .......................Absent
    System Power On Diagnostics Complete
    
    Currently running ROMMON from S (Gold) region
    Boot image: bootdisk:cat6000-sup32pfc3k8.8-5-8.bin
    
    
    Firmware compiled 01-Dec-06 12:57 by integ Build [100]
    
    This module is now in standby mode.
    Console is disabled for standby supervisor
    
  2. Console no supervisor 6, que é o módulo ativo agora.

    1. Status de redundância:

      Access2> (enable) show system highavailability
      Highavailability: enabled
      Highavailability versioning: disabled
      Highavailability Operational-status: ON
      
      Access2> (enable) show system redundancy-history
         Maximum entries of switchover history table = 10
         System cold start due to switchover failure = 4
         Standby available time (secs*100)          = 98984
      
         Redundant History Switchover Table:
            Index: 1
            Previous active supervisor module: 5
            Current active supervisor module : 6
            Switchover reason                : user initiated
            Switchover time                  : Mon May 21 2007, 20:40:37
    2. Versão da mostra:

      Access2> (enable) show version
      WS-C6509 Software, Version NmpSW: 8.5(8)
      Copyright (c) 1995-2006 by Cisco Systems
      NMP S/W compiled on Dec  1 2006, 23:03:43
      
      System Bootstrap Version: 12.2
      System Boot Image File is 'bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin'
      System Configuration register is 0x2102
    3. Variável de inicialização:

      Access2> (enable) show boot
      BOOT variable = bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin,1;bootdisk:cat6000
      -sup32pfc3k8.8-4-5.bin,1;
      CONFIG_FILE variable = bootdisk:switch.cfg
      
      Configuration register is 0x2102
      ignore-config: disabled
      auto-config: non-recurring, overwrite, sync disabled
      ROMMON console baud: 9600
      boot: image specified by the boot system commands
      
      Image auto sync is enabled
      Image auto sync timer is 120 seconds
    4. Módulo show:

      Access2> (enable) show module
      Mod Slot Ports Module-Type               Model               Sub Status
      --- ---- ----- ------------------------- ------------------- --- --------
      1   1          Unknown Card                                  power-down
      2   2    48    10/100BaseTX Ethernet     WS-X6248-RJ-45      no  ok
      3   3    48    10/100BaseTX Ethernet     WS-X6348-RJ-45      yes ok
      4   4    48    10/100BaseTX Ethernet     WS-X6348-RJ-45      yes ok
      5   5    9     1000BaseX Supervisor      WS-SUP32-GE-3B      yes standby
      6   6    9     1000BaseX Supervisor      WS-SUP32-GE-3B      yes ok
      16  6    1     Multilayer Switch Feature WS-F6K-MSFC2A       no  ok
      7   7    5     Communication Media Mod.  WS-SVC-CMM          no  ok
      8   8    0     FXS                                           no  power-down
      9   9          Unknown Card                                  power-down
      
      
      !--- Output suppressed
      
      
      Mod Sub-Type                Sub-Model           Sub-Serial  Sub-Hw Sub-Sw
      --- ----------------------- ------------------- ----------- ------ ------
      3   Inline Power Module     WS-F6K-VPWR                     1.0    1.1(1)
      4   Inline Power Module     WS-F6K-VPWR                     1.0    1.1(1)
      5   L3 Switching Engine III WS-F6K-PFC3B        SAL1012GREU 2.1
      6   L3 Switching Engine III WS-F6K-PFC3B        SAL1017L9WJ 2.1
      Access2> (enable)
  3. Verifique o MSFC:

    Access2> (enable) session 16
    Trying Router-16...
    Connected to Router-16.
    Escape character is '^]'.
    
    LAB-Router>enable
    
    LAB-Router#show version
    Cisco Internetwork Operating System Software
    IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), 
    Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by cisco Systems, Inc.
    Compiled Thu 23-Nov-06 01:03 by kellythw
    Image text-base: 0x40101040, data-base: 0x42638000
    
    ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1)
    BOOTLDR: MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7,
     RELEASE SOFTWARE (fc1)
    
    LAB-Router uptime is 7 minutes
    System returned to ROM by Stateful Switchover
    System image file is "bootflash:c6msfc2a-adventerprisek9_wan-mz.122-18.SXF7.bin"
    
    
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    
    If you require further assistance please contact us by sending email to
    export@cisco.com.
    
    cisco MSFC2A (R7000) processor (revision MSFC2A) with 458752K/65536K bytes of me
    mory.
    Processor board ID MSFC2A
    R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache
    Last reset from power-on
    SuperLAT software (copyright 1990 by Meridian Technology Corp).
    X.25 software, Version 3.0.0.
    Bridging software.
    TN3270 Emulation software.
    29 Virtual Ethernet/IEEE 802.3 interfaces
    509K bytes of non-volatile configuration memory.
    
    65536K bytes of Flash internal SIMM (Sector size 512K).
    Configuration register is 0x2102

Rebatize o OS do catalizador

Você pode ver que o nome de Cactos no módulo do supervisor substituído começa com RTSYNC. Você pode deixar o sistema para ser executado enquanto é. Você pode igualmente mudar o nome de arquivo e mantê-lo como um nome padrão como mostrado aqui:

Access2> (enable) rename RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin 
cat6000-sup32pfc3k 8.8-5-8.bin
Access2> (enable) dir
    2287   -rw-  10029260    May 21 2007 21:40:01 cat6000-sup32pfc3k8.8-5-8.bin

236900352 bytes available (19390464 bytes used)
Access2> (enable)

Depois que você rebatiza o arquivo, você deve mudar o variável de inicialização.


!--- Verify boot variable

Access2> (enable) show boot
BOOT variable = bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin,1;bootdisk:cat6000
-sup32pfc3k8.8-4-5.bin,1;
CONFIG_FILE variable = bootdisk:switch.cfg

Configuration register is 0x2102
ignore-config: disabled
auto-config: non-recurring, overwrite, sync disabled
ROMMON console baud: 9600
boot: image specified by the boot system commands

Image auto sync is enabled
Image auto sync timer is 120 seconds


!--- Clear all the boot variables

Access2> (enable) clear boot system all
BOOT variable =
Access2> (enable) 2007 May 21 21:41:56 %SYS-5-SUP_IMGSYNC:File synchronization p
rocess will start in 120 seconds


!--- Configure the boot variable

Access2> (enable) set boot system flash bootdisk:cat6000-sup32pfc3k8.8-5-8.bin
BOOT variable = bootdisk:cat6000-sup32pfc3k8.8-5-8.bin,1;
Access2> (enable) 2007 May 21 21:42:14 %SYS-5-SUP_IMGSYNC:File synchronization p
rocess will start in 120 seconds


!--- Verify the boot variable

Access2> (enable) show boot
BOOT variable = bootdisk:cat6000-sup32pfc3k8.8-5-8.bin,1;
CONFIG_FILE variable = bootdisk:switch.cfg

Configuration register is 0x2102
ignore-config: disabled
auto-config: non-recurring, overwrite, sync disabled
ROMMON console baud: 9600
boot: image specified by the boot system commands

Image auto sync is enabled
Image auto sync timer is 120 seconds

Informações Relacionadas


Document ID: 91897