IP : Simple Network Management Protocol (SNMP)

Objetos MIB equivalentes para comandos show de VoIP

19 Setembro 2015 - Tradução por Computador
Outras Versões: Versão em PDFpdf | Inglês (22 Agosto 2015) | Feedback


Índice


Introdução

Este capas de documento que os objetos MIB equivalentes que fornecem as partes de informação contiveram na vária Voz sobre comandos de verificação IP (VoIP). Os aplicativos NMS e/ou os scripts podem potencialmente usar esta informação.

Pré-requisitos

Requisitos

Não existem requisitos específicos para este documento.

Componentes Utilizados

Este documento não é restringido às versões de software específicas. Contudo, escreve-se especificamente para um Cisco 3600 Series Router com um cartão NM-2V.

As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. Todos os dispositivos utilizados neste documento foram iniciados com uma configuração (padrão) inicial. Se a sua rede estiver ativa, certifique-se de que entende o impacto potencial de qualquer comando.

Convenções

Para obter mais informações sobre convenções de documento, consulte as Convenções de dicas técnicas Cisco.

Configuração

Esta saída mostra uma porção relevante da configuração que este documento se usa:

VoipRouter#show running-configuration
Building configuration...

Current configuration : 5412 bytes
!
version 12.3
...
!
snmp-server community public RO
!
...
!
voice-port 2/0/0
!
...
!
dial-peer voice 2000 pots
 destination-pattern 2000
 port 2/0/0
!
dial-peer voice 1000 voip
 destination-pattern 1000
 session target ipv4:172.16.99.22
!
...
end

Comandos de VoIP

Estas seções mostram os objetos MIB que correspondem à saída destes comandos de verificação de VoIP:

A informação que estes comandos de verificação de VoIP contêm pode ser extraída do IF-MIB, do CISCO-VOICE-IF-MIB, do CISCO-VOICE-ANALOG-IF-MIB, do CISCO-VOICE-DIAL-CONTROL-MIB, do DIAL-CONTROL-MIB, e do CISCO-DSP-MGMT-MIB.

Nota: Nestes exemplos, o trecho de telefonia é posicionado por 1102799 e o pé de H.323 é posicionado por 1102966.

mostre o sumário da porta de voz

Nota: O texto em negrito no comando show voice port summary é esboçado na seção equivalente dos objetos MIB.

VoipRouter#show voice port summary
                                      IN           OUT
PORT      CH   SIG-TYPE   ADMIN OPER  STATUS       STATUS   EC
========= == ============ ===== ====  ========     ======== ==
2/0/0(A1) --  fxs-ls(A2)  up(A3)up(A4) off-hook(A5) idle     y(A6) 
2/0/1     --  fxs-ls      up    dorm   on-hook      idle     y 

Objetos MIB equivalentes

A1  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

A2  —  CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.37 = INTEGER: fxsLoopStart(1)

A3  —  IF-MIB::ifAdminStatus.37 = INTEGER: up(1)

A4  —  IF-MIB::ifOperStatus.37 = INTEGER: up(1)

A5  —  CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.37 = INTEGER: offHook(2)

A6  —  CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.37 = INTEGER: true(1)

Nota: Nenhum objeto MIB mantém o valor contido na parcela CH do comando show voice port summary quando o cartão NM-2V é usado.

mostre o sumário da chamada de voz

Nota: O texto em negrito no comando show voice call summary é esboçado na seção equivalente dos objetos MIB.

VoipRouter#show voice call summary
PORT         CODEC      VAD   VTSP STATE            VPM STATE
============ ========   ===   ==================== ======================
2/0/0(B1)    g729r8(B2) y(B3) S_CONNECT             FXSLS_CONNECT            
2/0/1         -         -       -                   FXSLS_ONHOOK             

Objetos MIB equivalentes

B1  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

B2  —  CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCoderTypeRate.
       1102966.1 = INTEGER: ietfg729r8000(25)

B3  —  CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveVADEnable.
       1102966.1 = INTEGER: true(1)

Nota: Nenhum objeto MIB mantém o provedor de serviços de telefonia por voz (VTSP) e estados VPM individualmente. Use o callActiveCallState de DIAL-CONTROL-MIB pelo contrário.

mostre o sumário da voz do dial peer

Nota: O texto em negrito no comando show dial-peer voice summary é esboçado na seção equivalente dos objetos MIB.

VoipRouter#show dial-peer voice summary
dial-peer hunt 0
             AD                                        PRE  PASS
TAG      TYPE     MIN     OPER    PREFIX DEST-PATTERN  FER  THRU SESS-TARGET   PORT
2000(C1) pots(C2)  up(C3)  up(C4) 9(C5)   2000(C6)     0(C7)                2/0/0(C8)
1000     voip      up      up             1000         0    syst ipv4:172.16.99.22(C9)   

Objetos MIB equivalentes

C1  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.2000 = INTEGER: 90

    —  DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.2000.90 = INTEGER: 37
C2  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.2000 = INTEGER: voice(1)

C3  —  IF-MIB::ifAdminStatus.37 = INTEGER: up(1)

C4  —  IF-MIB::ifOperStatus.37 = INTEGER: up(1)

C5  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDialDigitsPrefix.90 = STRING: 9

C6  —  DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.2000.90 = STRING: 2000

C7  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.90 = INTEGER: 0

C8  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

C9  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionTarget.91 = 
       STRING: ipv4:172.16.99.22

Nota: Nenhum objeto MIB mantém o valor contido na PASSAGEM do modem ATRAVÉS da parcela do método do comando show dial-peer summary.

show call ative voice brief

Nota: O texto em negrito no comando show call ative voice brief é esboçado na seção equivalente dos objetos MIB.

VoIPRouter#show call active voice brief 
   
<ID>:<start>hs.<index> +<connect> pid:<peer_id> <dir> <addr> <state>  
  dur hh:mm:ss tx:<packets>/<bytes> rx:<packets>/<bytes>  
 IP <ip>:<udp> rtt:<time>ms pl:<play>/<gap>ms lost:<lost>/<early>/<late>  
  delay:<last>/<min>/<max>ms <codec>  
  MODEMPASS <method> buf:<fills>/<drains> loss <overall%>  
<multipkt>/<corrected>  
   last <buf event time>s dur:<Min>/<Max>s  
 FR <protocol> [int dlci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>  
  sig:<on/off> <codec> (payload size)  
ATM <protocol> [int vpi/vci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>  
  sig:<on/off> <codec> (payload size)  
 Tele <int>:tx:<tot>/<v>/<fax>ms <codec> noise:<l> acom:<l> i/o:<l>/<l>  
dBm  
MODEMRELAY info:<rcvd>/<sent>/<resent> xid:<rcvd>/<sent>  
total:<rcvd>/<sent>/<drops>  
 Proxy <ip>:<audio udp>,<video udp>,<tcp0>,<tcp1>,<tcp2>,<tcp3> endpt: 
<type>/<manf>  
 bw:<req>/<act> codec:<audio>/<video>  
  tx:<audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120  
pkts>/<t120 bytes>  
 rx:<audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120  
pkts>/<t120 bytes>  
Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 1
MGCP call-legs: 0
Total call-legs: 2
11D9 : 1102799(D1)hs.1 +1324 pid:2000(D2) Answer(D3) 2000(D4) active(D5)
 dur 1d19h(D6) tx:7875641(D7)/157512782(D8) rx:7875955(D9)/157519081(D10)
 Tele 2/0/0(D11):1: tx:157515460(D12)/157514630(D13)/0ms g729r8(D14)
 noise:-56(D15) acom:5(D16)  i/0:-40(D17)/-46(D18) dBm

11D9 : 1102966hs.1 +1157 pid:1000 Originate 1000 active
 dur 1d19h tx:7875388/157507741 rx:7875641/157512782
 IP 172.16.99.22(D19):19066(D20) rtt:6ms(D21) pl:157496940(D22)/4770ms(D23)
 lost:52(D24)/1(D25)/325(D26) delay:67(D27)/55(D28)/132ms(D29) g729r8

Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 1
MGCP call-legs: 0
Total call-legs: 2

Objetos MIB equivalentes

D1  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveConnectionId.1102799.1
       = Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC

D2  —  DIAL-CONTROL-MIB::callActivePeerId.1102799.1 = INTEGER: 2000

D3  —  DIAL-CONTROL-MIB::callActiveCallOrigin.1102799.1 = INTEGER: answer(2)

D4  —  DIAL-CONTROL-MIB::callActivePeerAddress.1102799.1 = STRING: 2000

D5  —  DIAL-CONTROL-MIB::callActiveCallState.1102799.1 = INTEGER: active(4)

D6  —  DIAL-CONTROL-MIB::callActiveConnectTime.1102799.1 = Timeticks: 
       (1104123) 3:04:01.23
    —  DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16590203) 1 days, 
       22:05:02.03

D7  —  DIAL-CONTROL-MIB::callActiveTransmitPackets.1102799.1 = Gauge32: 7875641

D8  —  DIAL-CONTROL-MIB::callActiveTransmitBytes.1102799.1 = Gauge32: 157512782

D9  —  DIAL-CONTROL-MIB::callActiveReceivePackets.1102799.1 = Gauge32: 7875955

D10 —  DIAL-CONTROL-MIB::callActiveReceiveBytes.1102799.1 = Gauge32: 157519081

D11 —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

D12 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveTxDuration.
       1102799.1 = Gauge32: 157515460 milliseconds

D13 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveVoiceTxDuration.
       1102799.1 = Gauge32: 157514630 milliseconds

D14 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveCoderTypeRate.
       1102799.1 = INTEGER: ietfg729r8000(25)

D15 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveNoiseLevel.
       1102799.1 = INTEGER: -56 dBm

D16 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveACOMLevel.
       1102799.1 =  INTEGER: 5 dB

D17 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveInSignalLevel.
       1102799.1 = INTEGER: -40 dBm

D18 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveOutSignalLevel.
       1102799.1 = INTEGER: -46 dBm

D19 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteIPAddress.
       1102966.1 = IpAddress: 172.16.99.22

D20 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteUDPPort.
       1102966.1 = INTEGER: 19066

D21 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRoundTripDelay.
       1102966.1 = Gauge32: 6 milliseconds

D22 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveOnTimeRvPlayout.
       1102966.1 = Gauge32: 157496940 milliseconds

D23 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithSilence.
       1102966.1 = Gauge32: 1090 milliseconds
    —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithPrediction.
       1102966.1 = Gauge32: 3680 milliseconds
    —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithInterpolation.
       1102966.1 = Gauge32: 0 milliseconds

D24 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLostPackets.
       1102966.1 = Gauge32: 52 packets

D25 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEarlyPackets.
       1102966.1 = Gauge32: 1 packets

D26 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLatePackets.
       1102966.1 = Gauge32: 325 packets

D27 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveReceiveDelay.
       1102966.1 = Gauge32: 67

D28 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLoWaterPlayoutDelay.
       1102966.1 = Gauge32: 55 milliseconds

D29 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveHiWaterPlayoutDelay.
       1102966.1 = Gauge32: 132 milliseconds

Nota: O valor de GapFill do comando show call ative voice brief é obtido quando você adiciona o cvVoIPCallActiveGapFillWithSilence, o cvVoIPCallActiveGapFillWithPrediction, e o cvVoIPCallActiveGapFillWithInterpolation dos objetos SNMP.

mostre o DSP de voz

VoIPRouter#show voice dsp
 
DSP  DSP             DSPWARE CURR  BOOT                         PAK     TX/RX
TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
C549 009 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     05     0         0/36
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     06     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     07     0          0/0
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     08     0          0/0
C549 010 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     09     0          0/0
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     10     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     11     0          0/0
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     12     0          0/0
C549 011 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     13     0          0/0
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     14     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     15     0          0/0
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     16     0          0/0
C549 012 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     17     0          0/0
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     18     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     19     0          0/0
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     20     0          0/0
C549 013 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     21     0          0/0
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     22     0          0/0
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     23     0         0/12
         04 g729r8    4.1.31 busy  idle         0 1/0:0     24     0    176/56702
C549 014 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     01     0         0/27
         02 {medium}  4.1.31 IDLE  idle         0 1/0:0     02     0         0/12
         03 {medium}  4.1.31 IDLE  idle         0 1/0:0     03     0         0/12
         04 {medium}  4.1.31 IDLE  idle         0 1/0:0     04     0         0/12

Estão aqui alguns objetos MIB úteis que fornecem a informação sobre a chamada ativa nas saídas de exemplo do comando show voice dsp:

CISCO-DSP-MGMT-MIB::cdspCardIndex.7 = INTEGER: 2
OLD-CISCO-CHASSIS-MIB::cardType.2 = INTEGER: hdv(516)
OLD-CISCO-CHASSIS-MIB::cardDescr.2 = STRING: "High Density Voice"
ENTITY-MIB::entPhysicalDescr.7 = STRING: High Density Voice
ENTITY-MIB::entPhysicalDescr.22 = STRING: DSP (C549)
CISCO-DSP-MGMT-MIB::cdspCardState.7 = INTEGER: normal(1)
CISCO-DSP-MGMT-MIB::cdspCardMaxChanPerDSP.7 = Gauge32: 4 channels
CISCO-DSP-MGMT-MIB::cdspTotalChannels.22 = Gauge32: 4 channels
CISCO-DSP-MGMT-MIB::cdspActiveChannels.21 = Gauge32: 1 channels

Nota: O MIB que contém a informação para o DSP de voz da mostra é CISCO-DSP-MGMT-MIB. Contudo, devido à identificação de bug Cisco CSCeb62542 para o cartão NM-2V, os DSP no NM-2V não são mostrados no ENTITY-MIB. Desde que cdspCardStatusTable é dependente do entPhysicalIndex do ENTITY-MIB, cdspCardStatusTable não é povoado para o cartão NM-2V.

Apêndice

Esta saída mostra o snmpwalk completo do ciscoVoiceAnalogIfMIB do CISCO-VOICE-ANALOG-IF-MIB na altura dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 CISCO-VOICE-ANALOG-IF-MIB:ciscoVoiceAnalogIfMIB
CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgImpedance.37 = INTEGER: ohms600Real(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgImpedance.38 = INTEGER: ohms600Real(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgIntegratedDSP.37 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgIntegratedDSP.38 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusInfoType.37 = INTEGER: voice(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusInfoType.38 = INTEGER: none(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfMaintenanceMode.37 = INTEGER: none(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfMaintenanceMode.38 = INTEGER: none(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusSignalErrors.37 = Counter32: 0
CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusSignalErrors.38 = Counter32: 0
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.37 = INTEGER: fxsLoopStart(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.38 = INTEGER: fxsLoopStart(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingFrequency.37 = INTEGER: ringFrequency25(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingFrequency.38 = INTEGER: ringFrequency25(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.37 = INTEGER: offHook(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.38 = INTEGER: onHook(1)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingActive.37 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingActive.38 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingGround.37 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingGround.38 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTipGround.37 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTipGround.38 = INTEGER: false(2)
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingDigitDuration.37 = 
INTEGER: 100 milliseconds
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingDigitDuration.38 = 
INTEGER: 100 milliseconds
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingInterDigitDuration.37 = 
INTEGER: 100 milliseconds
CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingInterDigitDuration.38 = 
INTEGER: 100 milliseconds

Esta saída mostra o snmpwalk completo do ciscoVoiceInterfaceMIB do CISCO-VOICE-IF-MIB na altura dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 CISCO-VOICE-IF-MIB:ciscoVoiceInterfaceMIB
CISCO-VOICE-IF-MIB::cvIfCfgNoiseRegEnable.37 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgNoiseRegEnable.38 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgNonLinearProcEnable.37 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgNonLinearProcEnable.38 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgMusicOnHoldThreshold.37 = INTEGER: -38 dBm
CISCO-VOICE-IF-MIB::cvIfCfgMusicOnHoldThreshold.38 = INTEGER: -38 dBm
CISCO-VOICE-IF-MIB::cvIfCfgInGain.37 = INTEGER: 0 dB
CISCO-VOICE-IF-MIB::cvIfCfgInGain.38 = INTEGER: 0 dB
CISCO-VOICE-IF-MIB::cvIfCfgOutAttn.37 = INTEGER: 3 dB
CISCO-VOICE-IF-MIB::cvIfCfgOutAttn.38 = INTEGER: 3 dB
CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.37 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.38 = INTEGER: true(1)
CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelCoverage.37 = INTEGER: 4
CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelCoverage.38 = INTEGER: 4
CISCO-VOICE-IF-MIB::cvIfCfgConnectionMode.37 = INTEGER: normal(1)
CISCO-VOICE-IF-MIB::cvIfCfgConnectionMode.38 = INTEGER: normal(1)
CISCO-VOICE-IF-MIB::cvIfCfgConnectionNumber.37 = STRING: 
CISCO-VOICE-IF-MIB::cvIfCfgConnectionNumber.38 = STRING: 
CISCO-VOICE-IF-MIB::cvIfCfgInitialDigitTimeOut.37 = INTEGER: 10 seconds
CISCO-VOICE-IF-MIB::cvIfCfgInitialDigitTimeOut.38 = INTEGER: 10 seconds
CISCO-VOICE-IF-MIB::cvIfCfgInterDigitTimeOut.37 = INTEGER: 10 seconds
CISCO-VOICE-IF-MIB::cvIfCfgInterDigitTimeOut.38 = INTEGER: 10 seconds
CISCO-VOICE-IF-MIB::cvIfCfgRegionalTone.37 = STRING: "US"
CISCO-VOICE-IF-MIB::cvIfCfgRegionalTone.38 = STRING: "US"
CISCO-VOICE-IF-MIB::cvIfCfgEntry.13.37 = INTEGER: 1
CISCO-VOICE-IF-MIB::cvIfCfgEntry.13.38 = INTEGER: 1
CISCO-VOICE-IF-MIB::cvIfCfgEntry.14.37 = INTEGER: 1
CISCO-VOICE-IF-MIB::cvIfCfgEntry.14.38 = INTEGER: 1

Esta saída mostra o snmpwalk completo do ciscoVoiceDialControlMIB do CISCO-VOICE-DIAL-CONTROL-MIB na altura dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 CISCO-VOICE-DIAL-CONTROL-MIB:ciscoVoiceDialControlMIB
CISCO-VOICE-DIAL-CONTROL-MIB::cvGeneralPoorQoVNotificationEnable.0 = INTEGER: true(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.1000 = INTEGER: 91
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.2000 = INTEGER: 90
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.1000 = INTEGER: voip(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.2000 = INTEGER: voice(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgRowStatus.1000 = INTEGER: active(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgRowStatus.2000 = INTEGER: active(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgEntry.5.1000 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgEntry.5.2000 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgSessionTarget.90 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDialDigitsPrefix.90 = STRING: 9
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDIDCallEnable.90 = INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgCasGroup.90 = INTEGER: -1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgRegisterE164.90 = INTEGER: true(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgForwardDigits.90 = INTEGER: -1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgEntry.7.90 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionProtocol.91 = INTEGER: cisco(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgDesiredQoS.91 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgMinAcceptableQoS.91 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionTarget.91 = 
STRING: ipv4:172.16.99.22
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgCoderRate.91 = 
INTEGER: g729IETFr8000(16)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgFaxRate.91 = INTEGER: voiceRate(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgVADEnable.91 = INTEGER: true(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgExpectFactor.91 = 
INTEGER: 0 equipment impairment factor (eif)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgIcpif.91 = 
INTEGER: 20 equipment impairment factor (eif)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgPoorQoVNotificationEnable.91 = 
INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgUDPChecksumEnable.91 = INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgIPPrecedence.91 = INTEGER: 0
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgTechPrefix.91 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgDigitRelay.91 = Hex-STRING: 00 
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgCoderBytes.91 = INTEGER: 20 bytes
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgFaxBytes.91 = INTEGER: 20 bytes
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgInBandSignaling.91 = INTEGER: cas(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgEntry.23.91 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgIncomingDnisDigits.90 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgIncomingDnisDigits.91 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgMaxConnections.90 = 
INTEGER: -1 connections
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgMaxConnections.91 = 
INTEGER: -1 connections
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgApplicationName.90 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgApplicationName.91 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.90 = INTEGER: 0
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.91 = INTEGER: 0
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgHuntStop.90 = INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgHuntStop.91 = INTEGER: false(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.6.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.6.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.7.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.7.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.8.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.8.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.9.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.9.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.10.90 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.10.91 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveConnectionId.1102799.1 = 
Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveTxDuration.1102799.1 = 
Gauge32: 157515460 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveVoiceTxDuration.1102799.1 = 
Gauge32: 157514630 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveFaxTxDuration.1102799.1 = 
Gauge32: 0 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveCoderTypeRate.1102799.1 = 
INTEGER: ietfg729r8000(25)
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveNoiseLevel.1102799.1 = INTEGER: -56 dBm
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveACOMLevel.1102799.1 = INTEGER: 5 dB
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveOutSignalLevel.1102799.1 = 
INTEGER: -46 dBm
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveInSignalLevel.1102799.1 = 
INTEGER: -40 dBm
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveERLLevel.1102799.1 = INTEGER: 5 dB
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveSessionTarget.1102799.1 = STRING: 
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveImgPageCount.1102799.1 = Gauge32: 0 pages
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.13.1102799.1 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.14.1102799.1 = INTEGER: 2
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.15.1102799.1 = INTEGER: 19971
CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.17.1102799.1 = INTEGER: 5
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveConnectionId.1102966.1 = 
Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteIPAddress.1102966.1 = 
IpAddress: 172.16.99.22
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteUDPPort.1102966.1 = 
INTEGER: 19066
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRoundTripDelay.1102966.1 = 
Gauge32: 6 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSelectedQoS.1102966.1 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSessionProtocol.1102966.1 = 
INTEGER: cisco(2)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSessionTarget.1102966.1 = 
STRING: ipv4:172.16.99.22
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveOnTimeRvPlayout.1102966.1 = 
Gauge32: 157496940 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithSilence.1102966.1 = 
Gauge32: 1090 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithPrediction.1102966.1 = 
Gauge32: 3680 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithInterpolation.1102966.1 = 
Gauge32: 0 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithRedundancy.1102966.1 = 
Gauge32: 0 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveHiWaterPlayoutDelay.1102966.1 = 
Gauge32: 132 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLoWaterPlayoutDelay.1102966.1 = 
Gauge32: 55 milliseconds
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveReceiveDelay.1102966.1 = 
Gauge32: 67
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveVADEnable.1102966.1 = 
INTEGER: true(1)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveCoderTypeRate.1102966.1 = 
INTEGER: ietfg729r8000(25)
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLostPackets.1102966.1 = 
Gauge32: 52 packets
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEarlyPackets.1102966.1 = 
Gauge32: 1 packets
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLatePackets.1102966.1 = 
Gauge32: 325 packets
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.21.1102966.1 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.22.1102966.1 = ""
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.23.1102966.1 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.24.1102966.1 = 
STRING: "172.16.99.22"
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.25.1102966.1 = INTEGER: 1720
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.26.1102966.1 = INTEGER: 1
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.27.1102966.1 = 
STRING: "172.16.99.22"
CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.28.1102966.1 = INTEGER: 19066

Esta saída mostra o snmpwalk completo do ciscoVoiceCommonDialControlMIB do CISCO-VOICE-DIAL-CONTROL-MIB na altura dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 CISCO-VOICE-COMMON-DIAL-CONTROL-MIB:
ciscoVoiceCommonDialControlMIB
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveConnectionId.
1102966.1 = Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveVADEnable.
1102966.1 = INTEGER: true(1)
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCoderTypeRate.
1102966.1 = INTEGER: ietfg729r8000(25)
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCodecBytes.
1102966.1 = INTEGER: 20
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveInBandSignaling.
1102966.1 = INTEGER: cas(1)
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveEntry.6.
1102966.1 = ""
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveEntry.7.
1102966.1 = INTEGER: 2

Esta saída mostra o snmpwalk completo do dialControlMib de DIAL-CONTROL-MIB na altura dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 DIAL-CONTROL-MIB:dialControlMib
DIAL-CONTROL-MIB::dialCtlAcceptMode.0 = INTEGER: acceptAll(2)
DIAL-CONTROL-MIB::dialCtlTrapEnable.0 = INTEGER: enabled(1)
DIAL-CONTROL-MIB::dialCtlPeerCfgIfType.1000.91 = INTEGER: voiceOverIp(104)
DIAL-CONTROL-MIB::dialCtlPeerCfgIfType.2000.90 = INTEGER: voiceFXS(102)
DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.2000.90 = INTEGER: 37
DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.1000.91 = STRING: 1000
DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.2000.90 = STRING: 2000
DIAL-CONTROL-MIB::dialCtlPeerCfgAnswerAddress.1000.91 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerCfgAnswerAddress.2000.90 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerCfgSubAddress.1000.91 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerCfgSubAddress.2000.90 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerCfgSpeed.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgSpeed.2000.90 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgInfoType.1000.91 = INTEGER: speech(2)
DIAL-CONTROL-MIB::dialCtlPeerCfgInfoType.2000.90 = INTEGER: speech(2)
DIAL-CONTROL-MIB::dialCtlPeerCfgPermission.1000.91 = INTEGER: both(3)
DIAL-CONTROL-MIB::dialCtlPeerCfgPermission.2000.90 = INTEGER: both(3)
DIAL-CONTROL-MIB::dialCtlPeerCfgInactivityTimer.1000.91 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgInactivityTimer.2000.90 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgMinDuration.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgMinDuration.2000.90 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgMaxDuration.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgMaxDuration.2000.90 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgCarrierDelay.1000.91 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgCarrierDelay.2000.90 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgCallRetries.1000.91 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgCallRetries.2000.90 = INTEGER: 0
DIAL-CONTROL-MIB::dialCtlPeerCfgRetryDelay.1000.91 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgRetryDelay.2000.90 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgFailureDelay.1000.91 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgFailureDelay.2000.90 = INTEGER: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerCfgTrapEnable.1000.91 = INTEGER: disabled(2)
DIAL-CONTROL-MIB::dialCtlPeerCfgTrapEnable.2000.90 = INTEGER: disabled(2)
DIAL-CONTROL-MIB::dialCtlPeerCfgStatus.1000.91 = INTEGER: active(1)
DIAL-CONTROL-MIB::dialCtlPeerCfgStatus.2000.90 = INTEGER: active(1)
DIAL-CONTROL-MIB::dialCtlPeerStatsConnectTime.1000.91 = Gauge32: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerStatsConnectTime.2000.90 = Gauge32: 0 seconds
DIAL-CONTROL-MIB::dialCtlPeerStatsChargedUnits.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsChargedUnits.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsSuccessCalls.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsSuccessCalls.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsFailCalls.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsFailCalls.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsAcceptCalls.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsAcceptCalls.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsRefuseCalls.1000.91 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsRefuseCalls.2000.90 = Gauge32: 0
DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectCause.1000.91 = ""
DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectCause.2000.90 = ""
DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectText.1000.91 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectText.2000.90 = STRING: 
DIAL-CONTROL-MIB::dialCtlPeerStatsLastSetupTime.1000.91 = Timeticks: 
(1102966) 3:03:49.66
DIAL-CONTROL-MIB::dialCtlPeerStatsLastSetupTime.2000.90 = Timeticks: 
(1102799) 3:03:47.99
DIAL-CONTROL-MIB::callActivePeerAddress.1102799.1 = STRING: 2000
DIAL-CONTROL-MIB::callActivePeerAddress.1102966.1 = STRING: 1000
DIAL-CONTROL-MIB::callActivePeerSubAddress.1102799.1 = STRING: 
DIAL-CONTROL-MIB::callActivePeerSubAddress.1102966.1 = STRING: 
DIAL-CONTROL-MIB::callActivePeerId.1102799.1 = INTEGER: 2000
DIAL-CONTROL-MIB::callActivePeerId.1102966.1 = INTEGER: 1000
DIAL-CONTROL-MIB::callActivePeerIfIndex.1102799.1 = INTEGER: 90
DIAL-CONTROL-MIB::callActivePeerIfIndex.1102966.1 = INTEGER: 91
DIAL-CONTROL-MIB::callActiveLogicalIfIndex.1102799.1 = INTEGER: 37
DIAL-CONTROL-MIB::callActiveLogicalIfIndex.1102966.1 = INTEGER: 0
DIAL-CONTROL-MIB::callActiveConnectTime.1102799.1 = Timeticks: 
(1104123) 3:04:01.23
DIAL-CONTROL-MIB::callActiveConnectTime.1102966.1 = Timeticks: 
(1104123) 3:04:01.23
DIAL-CONTROL-MIB::callActiveCallState.1102799.1 = INTEGER: active(4)
DIAL-CONTROL-MIB::callActiveCallState.1102966.1 = INTEGER: active(4)
DIAL-CONTROL-MIB::callActiveCallOrigin.1102799.1 = INTEGER: answer(2)
DIAL-CONTROL-MIB::callActiveCallOrigin.1102966.1 = INTEGER: originate(1)
DIAL-CONTROL-MIB::callActiveChargedUnits.1102799.1 = Gauge32: 0
DIAL-CONTROL-MIB::callActiveChargedUnits.1102966.1 = Gauge32: 0
DIAL-CONTROL-MIB::callActiveInfoType.1102799.1 = INTEGER: speech(2)
DIAL-CONTROL-MIB::callActiveInfoType.1102966.1 = INTEGER: speech(2)
DIAL-CONTROL-MIB::callActiveTransmitPackets.1102799.1 = Gauge32: 7875641
DIAL-CONTROL-MIB::callActiveTransmitPackets.1102966.1 = Gauge32: 7875388
DIAL-CONTROL-MIB::callActiveTransmitBytes.1102799.1 = Gauge32: 157512782
DIAL-CONTROL-MIB::callActiveTransmitBytes.1102966.1 = Gauge32: 157507741
DIAL-CONTROL-MIB::callActiveReceivePackets.1102799.1 = Gauge32: 7875955
DIAL-CONTROL-MIB::callActiveReceivePackets.1102966.1 = Gauge32: 7875641
DIAL-CONTROL-MIB::callActiveReceiveBytes.1102799.1 = Gauge32: 157519081
DIAL-CONTROL-MIB::callActiveReceiveBytes.1102966.1 = Gauge32: 157512782
DIAL-CONTROL-MIB::callHistoryTableMaxLength.0 = INTEGER: 50
DIAL-CONTROL-MIB::callHistoryRetainTimer.0 = INTEGER: 15 minutes

Discussões relacionadas da comunidade de suporte da Cisco

A Comunidade de Suporte da Cisco é um fórum onde você pode perguntar e responder, oferecer sugestões e colaborar com colegas.


Informações Relacionadas


Document ID: 63607