Voz : CAS Digital

Configuração de E1 R2 Signaling e Troubleshooting

19 Setembro 2015 - Tradução por Computador
Outras Versões: Versão em PDFpdf | Tradução Manual (7 Abril 2008) | Inglês (22 Agosto 2015) | Feedback


Índice


Introdução

Este documento oferece as entradas do comando progressive que são necessárias para implantar a sinalização E1R2. Este documento também oferece informações de troubleshooting com comandos debug.

Nota: Antes que você use este documento, recomenda-se que você lê primeiramente a teoria de sinalização do E1 R2.

Pré-requisitos

Requisitos

Antes que você tente esta configuração, assegure-se de que você encontre estas condições prévias:

  • A sinalização R2 aplica-se ao E1 somente.

  • A sinalização R2 não é apoiada no roteador de Cisco MC3810.

  • A fim executar a sinalização R2 em Cisco 2600/3600 Series Router, este hardware é exigido:

    VWIC-1MFT-E1 ou VWIC-2MFT-E1 ou VWIC-2MFT-E1-DI junto com um destes módulos da densidade da Voz: NM-HDV (módulo de red de voz de gran densidad) ou NM-HD-2VE (módulo de rede de voz/fax das Comunicações IP 2-slot).

  • Defina o comando ds0-group (ou o CAS-grupo, com base na versão de Cisco IOS�) nos controladores E1 (Roteadores do AS5x00, do Cisco 2600/3600).

  • Use o comando cas-custom a fim personalizar as variações do E1 R2 para países diferentes ou regiões.

Componentes Utilizados

A informação neste documento é baseada nesta versão de software e hardware:

  • Cisco AS5300 com Cisco IOS Software Release 12.0.7T

Nota: A sinalização do E1 R2 foi introduzida aos Cisco 2600/3600 Series Router nos Cisco IOS Software Releases 12.1.2XH e 12.1(3)T.

As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. Todos os dispositivos utilizados neste documento foram iniciados com uma configuração (padrão) inicial. Se a sua rede estiver ativa, certifique-se de que entende o impacto potencial de qualquer comando.

Convenções

Para obter mais informações sobre convenções de documento, consulte as Convenções de dicas técnicas Cisco.

Configurar

Esta seção apresenta-o com a informação que você pode se usar a fim configurar o E1 R2.

Nota: A fim encontrar a informação adicional nos comandos que este documento se usa, refere-se a ferramenta de consulta de comandos (clientes registrados somente).

AS5300: Cisco IOS - Voice Feature Card (VFC) Software Compatibility

Antes que você execute o E1 R2 que sinaliza em um Cisco AS5300 Router, assegure-se de que sua versão de Cisco IOS Software esteja compatível com o Cisco VCWare no módulo E1. A fim verificar a compatibilidade de Cisco IOS Software, refira a matriz de compatibilidade do Cisco VCWare para o Cisco AS5300. Se as versões são incompatíveis, os módulos do processador do sinal digital (DSP) na placa de voz não carregam e o processamento de sinal de voz não ocorre.

Tipicamente, se a versão do Cisco VCWare é incompatível com o Cisco IOS Software, você pode inscrever o comando show vfc slot_number interface a fim ver este segundo as indicações deste exemplo.

eefje#show vfc 1 interface 
Rx: in ptr 18, outptr 0 
Tx: in ptr 14  outptr  14 
0 in hw queue, 0 queue head , 0 queue tail
Hardware is VFC out-of-band channel 
Interface : state RESET DSP instance (0x61048284)
dsp_number 0, Channel ID 0 
TX outstanding 0, max TX outstanding 0 
Received 18 packets, 1087 bytes, 0 giant packets
0 drops, 0 no buffers, 0 input errors 
121 bytes output, 14 frames output 
0 bounce errors 0 

DSP module 1 is not installed 
DSP module 2 is not installed 
DSP module 3 is not installed 
DSP module 4 is not installed 
DSP module 5 is not installed

Nas primeiras saídas de exemplo do comando show vfc slot_number interface, o número do módulo DSP não é indicações instaladas mostra que as versões são incompatíveis para esse número de módulo.

Este segundo grupo de saída é um exemplo dos módulos DSP que têm a versão correta do Cisco VCWare carregada:

eefje#show vfc 1 interface
Rx: in ptr 24, outptr 0 
TX: in ptr 15  outptr  15 
0 in hw queue, 0 queue head , 0 queue tail 
Hardware is VFC out-of-band channel 
Interface : state RESET DSP instance (0x618C6088)
dsp_number 0, Channel ID 0 
TX outstanding 0, max TX outstanding 0
Received 283288 packets, 15864278 bytes, 0 giant packets 
0 drops, 0 no buffers, 0 input errors 
1416459 bytes output,  141647 frames output 
0 bounce errors 0 

Slot 1, DSPM 1 (C542), DSP 1, Channel 1 
State RESET, DSP instance (0x61914BDC) 
TX outstanding 0, max TX outstanding 8 
Received 0 packets, 0 bytes, 0 giant packets 
0 drops, 0 no buffers, 0 input errors 
0 bytes output,  0 frames output 
0 bounce errors 0 

Slot 1, DSPM 1 (C542), DSP 2, Channel 1
State RESET, DSP instance (0x6191510C) 
TX outstanding 0, max TX outstanding 8 
Received 0 packets, 0 bytes, 0 giant packets 
0 drops, 0 no buffers, 0 input errors
0 bytes output,  0 frames output
0 bounce errors 0

A fim verificar a versão instalada do Cisco VCWare, inscreva o comando show vfc slot_number version vcware, segundo as indicações deste exemplo:

eefje#show vfc 1 version vcware
Voice Feature Card in Slot 1: 

VCware Version : 4.10 
ROM Monitor Version : 1.2
DSPware Version : 
Technology :  C542

Nota: Certifique-se que a versão de tecnologia do Cisco VCWare (c549 ou c542) combina a tecnologia de DSP instalada VFC (DSPM-542: suporte de voz de densidade única ou DSPM-549: suporte de voz de alta densidade).

Configurar o E1 R2

Termine estas etapas a fim configurar o E1 R2:

  1. Estabelecer o controlador E1 que conecta à private automatic branch exchange (posto privado de comutação automática) (PBX) ou ao interruptor.

    Assegure-se de que a moldação e a codificação de linha do E1 estejam ajustadas corretamente.

  2. Para o E1 que molda, escolha o CRC ou o NON-CRC.

  3. Para a codificação de linha E1, escolha o HDB3 ou o AMI.

  4. Para o origem do relógio E1, escolha interno ou a linha. Lembre-se de que PBXs diferentes possuem requisitos diferentes na fonte de tempo.

  5. Configurar o sinal de linha.

  6. Configurar a sinalização entre registros.

  7. Personalize a configuração com o comando cas-custom.

Configurar o sinal de linha

Use esta sequência de comandos a fim definir seu sinal de linha.

 eefje(config)#controller E1 0
 eefje(config-controller)#ds0-group 1 timeslots 1-15 type ?
...
r2-analog        R2 ITU Q411
r2-digital       R2 ITU Q421
r2-pulse         R2 ITU Supplement 7
...

Esta é a sequência de comandos para o Cisco IOS Software Release 11.3.

 eefje(config)#controller E1 0
 eefje(config-controller)#cas-group 1 timeslot 1-15 type ?
...

Nota: Se você promove do Cisco IOS Software Release 11.3 a 12.0, o comando new substitui velho automaticamente.

Configurar a sinalização entre registros

Este exemplo da sequência de comandos ilustra como configurar os tipos diferentes de sinalização entre registros:

 eefje(config)#controller E1 0
 eefje(config-controller)#ds0-group 1 timeslots 1-15 type r2-digital ?
dtmf               DTMF tone signaling
r2-compelled       R2 Compelled Register Signaling
r2-non-compelled   R2 Non Compelled Register Signaling
r2-semi-compelled  R2 Semi Compelled Register Signaling

A implementação Cisco da sinalização R2 tem o apoio do Dialed Number Identification Service (DNIS) permitido à revelia. Se você permite a opção da identificação de número automática (ANI), a reunião de informação DNIS está executada ainda. A especificação da opção ANI não desabilita a coleção DNIS. O DNIS é o número que é chamado. O ANI é o número do chamador. Por exemplo, se você configura um roteador chamado A para chamar um roteador chamado B, a seguir o número DNIS é atribuído ao roteador B e o número ANI é atribuído ao roteador que o A. ANI é similar ao ID de chamada.

Customização de E1 R2 com o comando cas-custom

Os subcommands sob o comando cas-custom são usados a fim acomodar as variantes do país. São usados igualmente a fim personalizar parâmetros da sinalização associada a canal (CAS). Esta sequência de comandos ilustra como você pode ver todas as opções do comando cas-custom.

eefje(config)#controller E1 0
eefje(config-controller)#cas-custom 1
eefje(config-ctrl-cas)#?
CAS custom commands:
  ani-digits           Expected number of ANI digits
  ani-timeout          Timeout for ANI digits
  answer-guard-time    Wait Between Group-B Answer Signal And Line Answer
  answer-signal        Answer signal to be used
  caller-digits        Digits to be collected before requesting CallerID
  category             Category signal
  country              Country Name
  debounce-time        Debounce Timer
  default              Set a command to its defaults
  dnis-complete        Send I-15 after DNIS digits for dial-out
  dnis-digits          Expected number of DNIS digits
  exit                 Exit from cas custom mode
  groupa-callerid-end  Send Group-A Caller ID End
  invert-abcd          invert the ABCD bits before TX and after rx
  ka                   kA Signal
  kd                   KD Signal
  metering             R2 network is sending metering signal
  nc-congestion        Non Compelled Congestion signal
  no                   Negate a command or set its defaults
  proceed-to-send      Suppress proceed-to-send signal for pulsed line signaling
  release-ack          Send Release Acknowledgment to Clear Forward
  release-guard-time   Release Guard Timer
  request-category     DNIS Digits to be collected before requesting category
  seizure-ack-time     Seizure to Acknowledge timer
  unused-abcd          Unused ABCD bit values

Para obter mais informações sobre dos parâmetros de comando cas personalizado, refira a personalização e1 r2 com o comando cas-custom.

Diagrama de Rede

Este documento utiliza a seguinte configuração de rede.

/image/gif/paws/12154/e1_r2_sig_fig4.gif

Configurações

Com a finalidade deste documento, estas são as três configurações R2 diferentes que são mostradas através da relação E1:

As configurações foram alteradas a fim mostrar somente à informação que este documento discute.

eefje configurado para o digital non-compelled R2
hostname eefje
!
controller E1 0
 clock source line primary
 dso-group 1 timeslots 1-15 type r2-digital r2-non-compelled
 cas-custom 1

!--- For more information on these commands 
!--- refer to 
ds0-group
 and 
cas-custom.



!
voice-port 0:1
 cptone BE 

!--- The cptone command is country specific. For more 
!--- information on this command,  refer to 
cptone
.

!
dial-peer voice 123 pots
 destination-pattern 123
 direct-inward-dial
 port 0:1
 prefix 123
!
dial-peer voice 567 voip
 destination-pattern 567
 session target ipv4:2.0.0.2
!

eefje configurado para R2 Digital Semi-obrigada
hostname eefje
!
controller E1 0
 clock source line primary
 ds0-group 1 timeslots 1-15 type r2-digital r2-semi-compelled
 cas-custom 1

!--- For more information on these commands 
!---  refer to 
ds0-group
 and 
cas-custom
. 

!
voice-port 0:1
 cptone BE

!--- The cptone command is country specific. For more 
!--- information on this command,  refer to 
cptone
.

dial-peer voice 123 pots
 destination-pattern 123
 direct-inward-dial
 port 0:1
 prefix 123
!
dial-peer voice 567 voip
 destination-pattern 567
 session target ipv4:2.0.0.2
!

eefje configurado para R2 ANI obrigado Digitas
hostname eefje
! controller E1 0 clock source line primary ds0-group
1 timeslots 1-15 type r2-digital r2-compelled ani cas-custom 1

!--- For more information on these commands 
!---  refer to 
ds0-group
 and 
cas-custom
. 

voice-port 0:1 cptone BE

!--- The cptone command is country specific. For more 
!--- information on this command,  refer to 
cptone
.

dial-peer voice 123 pots destination-pattern 123 direct-inward-dial port
0:1 prefix 123
!
dial-peer voice 567 voip destination-pattern 567 session
target ipv4:2.0.0.2
!

Verificar

No momento, não há procedimento de verificação disponível para esta configuração.

Troubleshooting

Esta seção fornece informações que podem ser usadas para o troubleshooting da sua configuração.

Pesquise defeitos falhas do E1 R2

Esta é a informação de Troubleshooting relevante a esta configuração. Siga estas instruções a fim pesquisar defeitos sua configuração.

  1. Verifique que o controlador E1 0 está acima.

    Se está para baixo, verifique a moldação, codificação de linha, origem do relógio, alarma, substituem o cabo, assentam o cartão, e assim por diante. Use o documento da personalização e1 r2 com o comando cas-custom como uma referência.

  2. Se você usa um AS5300, certifique-se dos DSP estejam instalados corretamente com o comando show vfc slot number interface.

  3. Configurar o Direct Inward Dial (FEZ) no par do serviço de telefonia tradicional (POTS), de modo que os dígitos recebidos sejam usados para escolher um peer de saída.

  4. Especifique o cptone (o cptone é específico para seu país) nas portas de voz.

    Um comando cptonecountry deve ser configurado a fim combinar o comando cas-custom country. Os conjuntos de parâmetro do cptone os toms de progresso de chamada para um país particular, e ajustam mais importante a codificação ao a-law ou à u-lei, que depende do país. A codificação do padrão para os E.U. é u-lei.

  5. Disposições da linha de compatibilidade e da sinalização de registro à configuração de switch.

  6. Gire sobre algum do debuga mostrado neste documento e estudam as saídas.

  7. Verifique para ver se há uma comunicação entre o roteador e o PBX ou comute:

    • A linha está capturada?

    • O roteador recebe/envia dígitos?

    • Encontre que tomam partido espaços livres o atendimento.

    Se possível, use os Cisco IOS Software Release os mais atrasados disponíveis no cisco.com.

comandos debug e show

A Output Interpreter Tool (somente clientes registrados) oferece suporte a determinados comandos show, o que permite exibir uma análise da saída do comando show.

Nota: Antes que você emita comandos debug, refira a informação importante em comandos Debug.

Nota: Para o Cisco IOS Software Release 12.0, use estes debuga:

  • debugar o cas - Para o sinal de linha.

  • debug csm voice - Para a sinalização entre registros.

  • debugar a ordem tudo do vtsp para ter a saída de todas as mensagens (dígitos) trocadas entre o PBX e o roteador.

Para o Cisco IOS Software Release IO 11.3, use estes comandos:

  • modem-Mgmt csm debugar-RBS - Para o sinal de linha (você necessidade de especificar primeiramente o serviço interno no modo de configuração.).

  • debug csm voice - Para a sinalização entre registros.

  • debugar a ordem tudo do vtsp para ter a saída de todas as mensagens (dígitos) trocadas entre o PBX e o roteador.

Para as Plataformas AS5400 e AS5350, use estes debuga:

  • debugar o r2 do sigsm - Para a sinalização entre registros

  • debugar a ordem tudo do vtsp para ter a saída de todas as mensagens (dígitos) trocadas entre o PBX e o roteador.

Exemplo de debug

Desde que há três configurações diferentes mostradas previamente neste documento, estão aqui três diferentes debugam:

Digital non-compelled R2: Chamada recebida a 567

A fim compreender melhor este resultado do debug, refira a teoria de sinalização do E1 R2.

eefje#show debug 
CAS:
 Channel Associated Signaling debugging is on
CSM Voice:
Voice Call Switching Module debugging is on
Voice Telephony session debugging is on
Voice Telephony dsp debugging is on
Voice Telephony error debugging is on
eefje#
eefje#
eefje#
Jan 6 10:41:28.677: from NEAT(0): (0/0): Rx SEIZURE (ABCD=0001)
Jan 6 10:41:28.717: VDEV_ALLOCATE: failed to allocate a device
Jan 6 10:41:28.717: VDEV_ALLOCATE: 1/28 is allocated
Jan 6 10:41:28.721: csm_vtsp_init_tdm (voice_vdev=0x620BF874)
Jan 6 10:41:28.721: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 2, 
dspm 1, dsp 5, dsp_channel 1
Jan 6 10:41:28.721: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 5, 
channel 3, bank 1, bp_channel 4, BP_stream 255
Jan 6 10:41:28.721: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0018): EVENT_CALL_DIAL_IN 
at slot 2 and port 16
Jan 6 10:41:28.721: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 2,
 port 16
Jan 6 10:41:28.721: csm_vtsp_start_digit_collect (voice_vdev=0x620BF874)
Jan 6 10:41:28.721:  Enter csm_connect_pri_vdev function
Jan 6 10:41:28.721: csm_connect_pri_vdev:tdm_allocate_BP_ts()call. BP TS allocated
 at BP_stream0, BP_Ch28,vdev_common 0x6 20BF8E4
Jan 6 10:41:28.721: to NEAT:(cid0018) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan0
Jan 6 10:41:28.721: vtsp_do_call_setup_ind
Jan 6 10:41:28.721: vtsp_do_call_setup_ind: Call ID=65681, guid=61FAF610
Jan 6 10:41:28.721: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0, 
id1=0, id2=0, calling=, called=
Jan 6 10:41:28.721: vtsp_do_call_setup_ind: redirect DN = reason =
 0vtsp_open_voice_and_set_params
Jan 6 10:41:28.721: dsp_close_voice_channel: [0:1:0] packet_len=8 channel_id 
 =8529 packet_id=75
Jan 6 10:41:28.721: dsp_open_voice_channel_20: [0:1:0] packet_Len=16 channel_id 
 =8529 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0
 serial_port=0
Jan 6 10:41:28.721: dsp_encap_config_20: [0:1:0] packet_Len=24 channel_id=8529
 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0
Jan 6 10:41:28.721: dsp_set_playout: [0:1:0] packet_Len=18 channel_id=8529
 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300
Jan 6 10:41:28.721: dsp_echo_canceller_control: [0:1:0] packet_Len=10 
channel_id=8529 packet_id=66 flags=0x0
Jan 6 10:41:28.721: dsp_set_gains: [0:1:0] packet_Len=12 channel_id=8529 
packet_id=91 in_gain=0 out_gain=0
Jan 6 10:41:28.721: dsp_vad_enable: [0:1:0] packet_Len=10 channel_id=8529 
packet_id=78 thresh=-38
Jan 6 10:41:28.721: dsp_voice_mode: [0:1:0] packet_Len=24 channel_id=8529 
packet_id=73 coding_type=1 voice_field_size=80 V AD_flag=0 echo_length=64 
comfort_noise=1 inband_detect=1 digit_relay=2  
AGC_flag=0vtsp_do_r2_start_digit(): dsp_dtmf_mode()
 dsp_dtmf_mode(VTSP_TONE_R2_MF_FORWARD_MODE)
Jan 6 10:41:28.725: dsp_dtmf_mode: [0:1:0] packet_Len=10 channel_id=8529
 packet_id=65 dtmf_or_mf=1vtsp_do_r2_start_digit():fsm_push(vtsp_r2_state_table)
Jan 6 10:41:28.725: csm_vtsp_call_setup_resp (vdev_info=0x620BF874, 
vtsp_cdb=0x621C5F3C)
Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat 
BP_stream0,BP_Ch28
Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:dst_tdm_chnl call. BP TS allocatedat
 stream 5, chan 3,BP_stream 255, BP_ch 4
Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat
 stream 5, chan 3,BP_stream 0, BP_ch 28
Jan 6 10:41:28.725: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK
 (DNIS=, ANI=) at slot 2, port 16
Jan 6 10:41:28.725: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_IDLE R2
 Got Event R2_START
Jan 6 10:41:28.821: CSM_RX_CAS_EVENT_FROM_NEAT:(0018):EVENT_START_RX_TONE at slot 2
 and port 16
Jan 6 10:41:28.821: from NEAT(0): (0/0): TX SEIZURE_ACK (ABCD=1101)

!--- Digit 5 is sent: Forward Signal Group I-5.

Jan 6 10:41:29.233: vtsp_process_dsp_message: 
MSG_TX_DTMF_DIGIT_BEGIN: digit=5,
 rtp_timestamp=0x0CA95D43 dc_digit_up
Jan 6 10:41:29.233: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (5)
Jan 6 10:41:29.233: CSM voice (2/16): Rcvd Digit detected(5)
Jan 6 10:41:29.233: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE: R2_IN_COLLECT_DNIS R2
 Got Event 5
Jan 6 10:41:29.365: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=5,
 duration=8321dc_digit
Jan 6 10:41:29.365: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (5)
Jan 6 10:41:29.365: CSM voice (2/16): Rcvd Digit detected(5)
Jan 6 10:41:29.365: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF

!--- Digit 6 is sent: Forward Signal Group I-6.

Jan 6 10:41:29.593: vtsp_process_dsp_message: 
MSG_TX_DTMF_DIGIT_BEGIN: digit=6,
 rtp_timestamp=0x0CA95D43 dc_digit_up
Jan 6 10:41:29.593: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (6)
Jan 6 10:41:29.593: CSM voice (2/16): Rcvd Digit detected(6)
Jan 6 10:41:29.593: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE: R2_IN_COLLECT_DNIS R2
 Got Event 6
Jan 6 10:41:29.725: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=6,
 duration=8321dc_digit
Jan 6 10:41:29.725: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (6)
Jan 6 10:41:29.725: CSM voice (2/16): Rcvd Digit detected(6)
Jan 6 10:41:29.725: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE: R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF

!--- Digit 7 is sent: Forward Signal Group I-7.

Jan 6 10:41:29.953: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: 
digit=7, rtp_timestamp=0x0CA95D43 dc_digit_up
Jan 6 10:41:29.953: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)
received digit (7)
Jan 6 10:41:29.953: CSM voice (2/16): Rcvd Digit detected(7)
Jan 6 10:41:29.953: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event 7
Jan 6 10:41:30.085: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: 
digit=7, duration=8321dc_digit
Jan 6 10:41:30.085: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C)received digit (7)
Jan 6 10:41:30.085: CSM voice (2/16): Rcvd Digit detected(7)
Jan 6 10:41:30.085: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE: R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF

!--- Timeout: 3 seconds (default timer - AS5300 assumes DNIS is finished).

Jan 6 10:41:32.953: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE: R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_TIMER

!--- Send digit 6: Backward Signal Group B-6  (subscriber's line free-charge).

Jan 6 10:41:32.953: vtsp_r2_generate_digits: vdev_common=0x620BF8E4, 
string=567dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 6#

Jan 6 10:41:32.953: dsp_dtmf_dialing: [0:1:0] packet_Len=36 channel_id=8529 
packet_id=90 string=6# digits=2, time_on=150, time_off=30
Jan 6 10:41:32.953:&   digit=e, components=2, freq_of_first=900, 
freq_of_second=780, amp_of_first=8192, amp_of_second=8192
Jan 6 10:41:32.953:    digit=o, components=2, freq_of_first=0,  
freq_of_second=0, amp_of_first=1, amp_of_second=1
Jan 6 10:41:33.313: vtsp_process_dsp_message: 
MSG_TX_DIALING_DONE dc_dialing_done()
Jan 6 10:41:33.313: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE:R2_IN_ANSWER_PULSE R2
 Got Event R2_DIGITS_GENR2_ALERTING
Jan 6 10:41:34.313: R2 Incoming Voice(2/16): DSX (E1 0:0): 
STATE: R2_IN_ANSWER_PULSE R2
 Got Event R2_TONE_TIMER
Jan 6 10:41:34.313:  R2_IN_IDLE:2 r2_in_connect called
Jan 6 10:41:34.313: CSM_PROC_IC1_COLLECT_ADDR_INFO: 
 CSM_EVENT_ADDR_INFO_COLLECTED (DNIS=567, ANI=) at slot 2, port 16
Jan 6 10:41:34.313: vtsp_tsp_call_accept_check (sdb=0x61B8F0E0, calling_number=
 called_number=567): peer_tag=0
Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device
Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem
Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device
Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem
Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device
Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem
Jan 6 10:41:34.313: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 2,
 port 16
Jan 6 10:41:34.313: vtsp_ic_switch : (voice_vdev= 0x620BF874)
Jan 6 10:41:34.313: vtsp_tsp_call_switch_ind (cdb=0x621C5F3C, tsp_info=0x620BF874,
 calling_number= called_number=567 redir ect_number=): 
peer_tag=123dc_switch: fsm_pop()
Jan 6 10:41:34.313: vtsp_do_call_setup_ind
Jan 6 10:41:34.313: vtsp_do_call_setup_ind: Call ID=65683, guid=61FAF610
Jan 6 10:41:34.313: vtsp_do_call_setup_ind: type=0, under_spec=0,
 name=ab^Lx, id0=1, id1=0, id2=0, calling=123, called=567
Jan 6 10:41:34.317: dsp_cp_tone_off: [] packet_Len=8 channel_id=8529 packet_id=71
Jan 6 10:41:34.317: dsp_idle_mode: [] packet_Len=8 channel_id=8529 packet_id=68
Jan 6 10:41:34.317: dsp_close_voice_channel: [] packet_Len=8 channel_id=8529 
packet_id=75
Jan 6 10:41:34.317: vtsp_timer_stop: 67475758
Jan 6 10:41:34.317: csm_vtsp_call_setup_resp (vdev_info=0x620BF874,
 vtsp_cdb=0x621C5F3C)
Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:vdev_common 
BP TS allocatedat BP_stream0,
 BP_Ch28
Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat
 stream 5, chan 3,BP_stream 0, BP_ch 28
Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat
 stream 5, chan 3,BP_stream 0, BP_ch 28vt sp_open_voice_and_set_params
Jan 6 10:41:34.317: dsp_close_voice_channel: [0:1 (54)] packet_Len=8 channel_id=8529
 packet_id=75
Jan 6 10:41:34.317: dsp_open_voice_channel_20: [0:1 (54)] packet_Len=16 
channel_id=8529
 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0 
serial_port=0
Jan 6 10:41:34.317: dsp_encap_config_20: [0:1 (54)] packet_Len=24 channel_id=8529
 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0
Jan 6 10:41:34.317: dsp_set_playout: [0:1 (54)] packet_Len=18 channel_id=8529
 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300
Jan 6 10:41:34.317: dsp_echo_canceller_control: [0:1 (54)] packet_Len=10 
channel_id=8529
 packet_id=66 flags=0x0
Jan 6 10:41:34.317: dsp_set_gains: [0:1 (54)] packet_Len=12 
channel_id=8529 packet_id=91
 in_gain=0 out_gain=0
Jan 6 10:41:34.317: dsp_vad_enable: [0:1 (54)] packet_Len=10 
channel_id=8529 packet_id=78
 thresh=-38act_proceeding
Jan 6 10:41:34.321: csm_vtsp_call_proceeding:DST_tdm_chnl call. 
BP TS allocatedstream 5,
 chan 3,BP_stream 0, BP_ch 28act_alert
Jan 6 10:41:34.345: vtsp_ring_noan_timer_start: 67475761
Jan 6 10:41:34.345: csm_vtsp_call_alert (vtsp_cdb=0x621C5F3C)act_bridge act_caps_ind
Jan 6 10:41:34.589: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20,
    FaxRate 2, FaxBytes 20 SignalType 0
    DtmfRelay 1, Modem 1act_caps_ack
Jan 6 10:41:34.589: dsp_idle_mode: [0:1 (54)] packet_Len=8 
channel_id=8529 packet_id=68
Jan 6 10:41:34.589: act_caps_ack: codec = 15, ret = 1
Jan 6 10:41:34.589: dsp_cp_tone_off: [0:1 (54)] packet_Len=8 channel_id=8529 
  packet_id=71 
Jan 6 10:41:34.589: dsp_idle_mode: [0:1 (54)] packet_Len=8 
channel_id=8529 packet_id=68 
Jan 6 10:41:34.589: dsp_encap_config_20: [0:1 (54)] packet_Len=24 channel_id=8529 
  packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 
Jan 6 10:41:34.589: dsp_voice_mode: [0:1 (54)] packet_Len=24 channel_id=8529 
 packet_id=73 coding_type=20 voice_field_size=20 VAD_flag=1 echo_length=64
 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect 
Jan 6 10:41:36.857: vtsp_ring_noan_timer_stop: 67476012 
Jan 6 10:41:36.857: dsp_cp_tone_off: [0:1 (54)] packet_Len=8 channel_id=8529 
  packet_id=71 
Jan 6 10:41:36.857: csm_vtsp_call_connect (vtsp_cdb=0x621C5F3C, 
voice_vdev=0x620BF874) 
Jan 6 10:41:36.857: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK 
  at slot 2, port 16 
Jan 6 10:41:36.917: CSM_RX_CAS_EVENT_FROM_NEAT:(0018):  EVENT_CHANNEL_CONNECTED 
  at slot 2 and port 16 
Jan 6 10:41:36.917: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED 
  at slot 2, port 16 
Jan 6 10:41:36.921: from NEAT(0): (0/0): TX ANSWERED(ABCD=0101)
eefje#

R2 Digital Semi-obrigada: Chamada recebida a 567

A fim compreender melhor este resultado do debug, refira a teoria de sinalização do E1 R2.

eefje#show debug 
CAS:
 Channel Associated Signaling debugging is on
CSM Voice:
Voice Call Switching Module debugging is on 
Voice Telephony session debugging is on
Voice Telephony dsp debugging is on
Voice Telephony error debugging is on
eefje#
eefje#
eefje#
Jan  6 09:53:42.389: from NEAT(0): (0/2): Rx SEIZURE(ABCD=0001)
Jan 6 09:53:42.433: VDEV_ALLOCATE: failed to allocate a device
Jan 6 09:53:42.433: VDEV_ALLOCATE: 1/27 is allocated
Jan 6 09:53:42.433: csm_vtsp_init_tdm (voice_vdev=0x620BF320)
Jan 6 09:53:42.433: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 2, dspm 1,
 dsp 4, dsp_channel 4
Jan 6 09:53:42.433: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 7, channel 0,
 bank 4, BP_channel 3, BP_stream 255
Jan 6 09:53:42.433: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0017): EVENT_CALL_DIAL_IN
 at slot 2 and port 15
Jan 6 09:53:42.433: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT
 at slot 2, port 15
Jan 6 09:53:42.433: csm_vtsp_start_digit_collect (voice_vdev=0x620BF320)
Jan 6 09:53:42.433:  Enter csm_connect_pri_vdev function
Jan 6 09:53:42.433: csm_connect_pri_vdev:tdm_allocate_BP_Ts()call. BP TS allocated
 at BP_stream0, BP_Ch27,vdev_common 0x6 20BF390
Jan 6 09:53:42.433: to NEAT:(cid0017) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan2
Jan 6 09:53:42.433: vtsp_do_call_setup_ind
Jan 6 09:53:42.433: vtsp_do_call_setup_ind: Call ID=65675, guid=61FAF610
Jan 6 09:53:42.433: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0,
 id1=0, id2=0, calling=, called=
Jan 6 09:53:42.433: vtsp_do_call_setup_ind: redirect DN = reason =
 0vtsp_open_voice_and_set_params
Jan 6 09:53:42.433: dsp_close_voice_channel: [0:1:2] packet_Len=8 channel_id=8516
 packet_id=75
Jan 6 09:53:42.433: dsp_open_voice_channel_20: [0:1:2] packet_Len=16 
channel_id=8516
 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 
time_slot=1 serial_port=1
Jan 6 09:53:42.433: dsp_encap_config_20: [0:1:2] packet_Len=24 channel_id=8516
 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0
Jan 6 09:53:42.433: dsp_set_playout: [0:1:2] packet_Len=18 channel_id=8516 
 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300
Jan 6 09:53:42.433: dsp_echo_canceller_control: [0:1:2] 
packet_Len=10 channel_id=8516
 packet_id=66 flags=0x0
Jan 6 09:53:42.437: dsp_set_gains:[0:1:2] packet_Len=12 
channel_id=8516 packet_id=91
 in_gain=0 out_gain=0
Jan 6 09:53:42.437: dsp_vad_enable: [0:1:2] packet_Len=10 channel_id=8516
 packet_id=78 thresh=-38
Jan 6 09:53:42.437: dsp_voice_mode: [0:1:2] packet_Len=24 channel_id=8516
 packet_id=73 coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64
 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0vtsp_do_r2_start_digit():
 dsp_dtmf_mode() dsp_dtmf_mode(VTSP_TONE_R2_MF_FORWARD_MODE)
Jan 6 09:53:42.437: dsp_dtmf_mode: [0:1:2] packet_Len=10 channel_id=8516
 packet_id=65 dtmf_or_mf=1vtsp_do_r2_start_digit(): fsm_push(vtsp_r2_state_table)
Jan 6 09:53:42.437: csm_vtsp_call_setup_resp (vdev_info=0x620BF320, 
vtsp_cdb=0x621C5F3C)
Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:vdev_common BP 
TS allocatedat BP_stream0,
 BP_Ch27
Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat
 stream 7, chan 0,BP_stream 255, BP_ch 3
Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat
 stream 7, chan 0,BP_stream 0, BP_ch 27
Jan 6 09:53:42.437: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK
 (DNIS=, ANI=) at slot 2, port 15
Jan 6 09:53:42.437: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_IDLE R2
 Got Event R2_START
Jan 6 09:53:42.533: CSM_RX_CAS_EVENT_FROM_NEAT:(0017):EVENT_START_RX_TONE
 at slot 2 and port 15
Jan 6 09:53:42.533: from NEAT(0): (0/2): TX SEIZURE_ACK (ABCD=1101)

!--- Digit 5 is sent: Forward Signal Group I-5.

Jan 6 09:53:42.641: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:
 digit=5, rtp_timestamp=0x9330B42B dc_digit_up
Jan 6 09:53:42.641: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (5)
Jan 6 09:53:42.641: CSM voice (2/15): Rcvd Digit detected(5)
Jan 6 09:53:42.641: R2 Incoming Voice(2/15): DSX (E1 0:2): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event 5

!--- Digit 1 sent (pulse): Backward Signal Group A-1  (Send next digit) 
!--- "#" this indicates that it is a pulse). 

Jan 6 09:53:42.641: vtsp_r2_generate_digits: vdev_common=0x620BF390, 
string=5dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:42.641: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516
 packet_id=90 string=1# digits=2, time_on=150, time_off=30
Jan 6 09:53:42.641:    digit=`, components=2, freq_of_first=1020, 
freq_of_second=1140,
 amp_of_first=8192, amp_of_second=8192
Jan 6 09:53:42.641:    digit=o, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1
Jan 6 09:53:42.741: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=5,
 duration=8291dc_digit
Jan 6 09:53:42.741: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (5)
Jan 6 09:53:42.741: CSM voice (2/15): Rcvd Digit detected(5)
Jan 6 09:53:42.741: R2 Incoming Voice(2/15): DSX (E1 0:2): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF

!--- Digit 6 is sent: Forward Signal Group I.

Jan 6 09:53:42.881: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:
digit=6, rtp_timestamp=0x9330B42B dc_digit_up
Jan 6 09:53:42.881: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)received digit (6)
Jan 6 09:53:42.881: CSM voice (2/15): Rcvd Digit detected(6)
Jan 6 09:53:42.881: R2 Incoming Voice(2/15): DSX (E1 0:2):
 STATE:R2_IN_COLLECT_DNIS R2
 Got Event 6

!--- Digit 1 sent (pulse): Backward Signal Group A-1. (Send next digit.)

Jan 6 09:53:42.881: vtsp_r2_generate_digits: vdev_common=0x620BF390, 
string=56dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:42.881: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516
 packet_id=90 string=1# digits=2, time_on=150, time_off=30
Jan 6 09:53:42.881:    digit=`, components=2, freq_of_first=1020, 
freq_of_second=1140,
 amp_of_first=8192, amp_of_second=8192
Jan 6 09:53:42.881:    digit=o, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1
Jan 6 09:53:42.981: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=6,
 duration=8291dc_digit
Jan 6 09:53:42.981: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (6)
Jan 6 09:53:42.981: CSM voice (2/15): Rcvd Digit detected(6)
Jan 6 09:53:42.981: R2 Incoming Voice(2/15): DSX (E1 0:2): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF

!--- Digit 7 is sent: Forward Signal Group I-7.

Jan 6 09:53:43.121: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:
 digit=7, rtp_timestamp=0x9330B42B dc_digit_up
Jan 6 09:53:43.121: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)received digit (7)
Jan 6 09:53:43.121: CSM voice (2/15): Rcvd Digit detected(7)
Jan 6 09:53:43.121: R2 Incoming Voice(2/15): DSX (E1 0:2): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event 7

!--- Send digit 1 (pulse): Backward Signal Group A-1.

Jan 6 09:53:43.121: vtsp_r2_generate_digits: vdev_common=0x620BF390, 
string=567dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:43.121: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516
 packet_id=90 string=1# digits=2, time_on=150, time_off=30
Jan 6 09:53:43.121:    digit=`, components=2, freq_of_first=1020, 
freq_of_second=1140,
 amp_of_first=8192, amp_of_second=8192
Jan 6 09:53:43.121:    digit=o, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1
Jan 6 09:53:43.221: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7,
 duration=8291dc_digit
Jan 6 09:53:43.221: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (7)
Jan 6 09:53:43.221: CSM voice (2/15): Rcvd Digit detected(7)
Jan 6 09:53:43.221: R2 Incoming Voice(2/15): DSX (E1 0:2): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF
Jan 6 09:53:43.489: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()

!--- Timeout is 3 seconds.

Jan 6 09:53:46.121: R2 Incoming Voice(2/15): DSX (E1 0:2): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_TIMER

!--- Digit 3 sent(pulse): Backward Signal Group A-3.
!--- (Address-complete, changeover to reception of Group-B signals).

Jan 6 09:53:46.121: vtsp_r2_generate_digits: vdev_common=0x620BF390,
 string=567dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 3#
Jan 6 09:53:46.121: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516
 packet_id=90 string=3# digits=2, time_on=150, time_off=30
Jan 6 09:53:46.121:    digit=b, components=2, freq_of_first=1020, 
freq_of_second=900,
 amp_of_first=8192, amp_of_second=8192
Jan 6 09:53:46.121:    digit=o, components=2, freq_of_first=0,
freq_of_second=0, amp_of_first=1, amp_of_second=1

!--- Digit 1 is sent: Forward Signal Group II-1 
!--- (subscriber without priority).

Jan 6 09:53:46.361: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:
digit=1, rtp_timestamp=0x9330B42B dc_digit_up
Jan 6 09:53:46.361: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)
received digit (1)
Jan 6 09:53:46.361: CSM voice (2/15): Rcvd Digit detected(1)
Jan 6 09:53:46.361: R2 Incoming Voice(2/15): DSX (E1 0:2): 
STATE:R2_IN_CATEGORY R2
 Got Event 1
Jan 6 09:53:46.361:  r2_comp_category:R2_ALERTING

!--- Digit 6 sent (pulse): Backward Signal Group B-6 
!--- (the subscriber line free of charge).

Jan 6 09:53:46.361: vtsp_r2_generate_digits: vdev_common=0x620BF390, 
string=567dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 6#

Jan  6 09:53:46.361: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516
 packet_id=90 string=6# digits=2, time_on=150, time_off=30
Jan 6 09:53:46.361:    digit=e, components=2, freq_of_first=900, 
freq_of_second=780,
 amp_of_first=8192, amp_of_second=8192
Jan 6 09:53:46.361:    digit=o, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1
Jan 6 09:53:46.461: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=1,
 duration=8291dc_digit
Jan 6 09:53:46.461: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C)received digit (1)
Jan 6 09:53:46.461: CSM voice (2/15): Rcvd Digit detected(1)
Jan 6 09:53:46.461: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COMPLETE R2
 Got Event R2_TONE_OFF
Jan 6 09:53:46.729: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()
Jan 6 09:53:47.461: R2 Incoming Voice(2/15): DSX (E1 0:2): 
STATE:R2_IN_WAIT_GUARD R2
 Got Event R2_TONE_TIMER
Jan 6 09:53:47.461:  R2_IN_IDLE:2 r2_in_connect called
Jan 6 09:53:47.461: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_ADDR_INFO_COLLECTED
(DNIS=567, ANI=) at slot 2, port 15
Jan 6 09:53:47.461: vtsp_tsp_call_accept_check (sdb=0x61B8F0E0,calling_number=
 called_number=567): peer_tag=0
Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device
Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem
Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device
Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem
Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device
Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem
Jan 6 09:53:47.461: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 2,
 port 15
Jan 6 09:53:47.461: vtsp_IC_switch : (voice_vdev= 0x620BF320)
Jan 6 09:53:47.461: vtsp_tsp_call_switch_ind (cdb=0x621C5F3C,tsp_info=0x620BF320,
 calling_number= called_number=567 redirect_number=): 
peer_tag=123dc_switch: fsm_pop()
Jan 6 09:53:47.461: vtsp_do_call_setup_ind
Jan 6 09:53:47.461: vtsp_do_call_setup_ind: Call ID=65677, guid=61FAF610
Jan 6 09:53:47.461: vtsp_do_call_setup_ind: type=0, under_spec=0, name=AB^Lo, id0=3,
 id1=0, id2=0, calling=123, called=567
Jan 6 09:53:47.465: dsp_cp_tone_off: [] packet_Len=8 channel_id=8516 packet_id=71
Jan 6 09:53:47.465: dsp_idle_mode: [] packet_Len=8 channel_id=8516 packet_id=68
Jan 6 09:53:47.465: dsp_close_voice_channel: [] packet_Len=8 channel_id=8516 
packet_id=75
Jan 6 09:53:47.465: vtsp_timer_stop: 67189073
Jan 6 09:53:47.465: csm_vtsp_call_setup_resp (vdev_info=0x620BF320,
 vtsp_cdb=0x621C5F3C)
Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:vdev_common 
BP TS allocatedat BP_stream0,
 BP_Ch27
Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat
 stream 7, chan 0,BP_stream 0, BP_ch 27
Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat
 stream 7, chan 0,BP_stream 0, BP_ch 27vtsp_open_voice_and_set_params
Jan 6 09:53:47.465: dsp_close_voice_channel: [0:1 (52)] packet_Len=8 channel_id=8516
 packet_id=75
Jan 6 09:53:47.465: dsp_open_voice_channel_20: [0:1 (52)] 
packet_Len=16 channel_id=8516
 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 
time_slot=1 serial_port=1
Jan 6 09:53:47.465: dsp_encap_config_20: [0:1 (52)] packet_Len=24 
channel_id=8516
 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0
Jan 6 09:53:47.465: dsp_set_playout: [0:1 (52)] packet_Len=18 channel_id=8516
 packet_id=76 mode=1 initial=60 min=4 max=200  fax_nom=300
Jan& 6 09:53:47.465: dsp_echo_canceller_control: [0:1 (52)] packet_Len=10 
channel_id=8516
 packet_id=66 flags=0x0
Jan 6 09:53:47.465: dsp_set_gains: [0:1 (52)] packet_Len=12 channel_id=8516
 packet_id=91 in_gain=0 out_gain=0
Jan 6 09:53:47.465: dsp_vad_enable: [0:1 (52)] packet_Len=10 channel_id=8516
 packet_id=78 thresh=-38act_proceeding
Jan 6 09:53:47.469: csm_vtsp_call_proceeding:DST_tdm_chnl call. BP TS 
allocatedstream 7,
 chan 0,BP_stream 0, BP_ch 27act_alert
Jan 6 09:53:47.493: vtsp_ring_noan_timer_start: 67189076
Jan 6 09:53:47.493: csm_vtsp_call_alert (vtsp_cdb=0x621C5F3C)
act_bridge act_caps_ind
Jan 6 09:53:47.737: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20,
 FaxRate 2, FaxBytes 20 SignalType 0
 DtmfRelay 1, Modem 1act_caps_ack
Jan 6 09:53:47.737: dsp_idle_mode: [0:1 (52)] packet_Len=8 channel_id=8516 
packet_id=68
Jan 6 09:53:47.737: act_caps_ack: codec = 15, ret = 1
Jan 6 09:53:47.737: dsp_cp_tone_off: [0:1 (52)] packet_Len=8 channel_id=8516 
 packet_id=71 
Jan 6 09:53:47.737: dsp_idle_mode: [0:1 (52)] packet_Len=8 channel_id=8516 
 packet_id=68 
Jan 6 09:53:47.737: dsp_encap_config_20: [0:1 (52)] packet_Len=24 channel_id=8516 
 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 
Jan 6 09:53:47.737: dsp_voice_mode: [0:1 (52)] packet_Len=24 channel_id=8516 
 packet_id=73 coding_type=20 voice_field_size= 20 VAD_flag=1 echo_length=64
 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect 
Jan 6 09:53:49.461: vtsp_ring_noan_timer_stop: 67189273 
Jan 6 09:53:49.461: dsp_cp_tone_off: [0:1 (52)] packet_Len=8 channel_id=8516 
  packet_id=71 
Jan 6 09:53:49.461: csm_vtsp_call_connect (vtsp_cdb=0x621C5F3C, 
voice_vdev=0x620BF320) 
Jan 6 09:53:49.461: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK 
  at slot 2, port 15 
Jan 6 09:53:49.617: CSM_RX_CAS_EVENT_FROM_NEAT:(0017):  EVENT_CHANNEL_CONNECTED 
  at slot 2 and port 15
Jan 6 09:53:49.617: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED 
  at slot 2, port 15 
Jan 6 09:53:49.621: from NEAT(0): (0/2): TX ANSWERED(ABCD=0101)
eefje#
eefje#

R2 ANI obrigado Digitas: Chamada recebida a 567

A fim compreender melhor este resultado do debug, refira a teoria de sinalização do E1 R2.

eefje#debug csm voice 
Voice Call Switching Module debugging is on 
eefje#debug cas
Channel Associated Signaling debugging is on 
Jan 7 10:00:02.907: from NEAT(0): debug-cas is on 
Jan 7 10:00:02.907: from NEAT(0): special debug-cas is offg vtsp all 
Voice telephony call control all debugging is on
eefje# 
eefje#
Jan 7 10:00:23.883: from NEAT(0): (0/8): Rx SEIZURE (ABCD=0001) 
Jan 7 10:00:23.927: VDEV_ALLOCATE: failed to allocate a device 
Jan 7 10:00:23.927: VDEV_ALLOCATE: 1/2 is allocated 
Jan 7 10:00:23.927: csm_vtsp_init_tdm (voice_vdev=0x61F19688) 
Jan 7 10:00:23.927: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 1, 
dspm 3, dsp 4,
 dsp_channel 1 
Jan 7 10:00:23.927: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 5, 
channel 13,
 bank 0, BP_channel 15, BP_stream 255 
Jan 7 10:00:23.927: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0007): 
EVENT_CALL_DIAL_IN at slot 1
 and port 60 
Jan 7 10:00:23.927: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 1, port 60 
Jan 7 10:00:23.927: csm_vtsp_start_digit_collect (voice_vdev=0x61F19688) 
Jan 7 10:00:23.927:  Enter csm_connect_pri_vdev function 
Jan 7 10:00:23.927: csm_connect_pri_vdev:tdm_allocate_BP_Ts() call. BP 
TS allocated at BP_stream0, BP_Ch8,vdev_common 0x6205E5F8 
Jan 7 10:00:23.927: to NEAT:(cid0007) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan8 
Jan 7 10:00:23.927: vtsp_do_call_setup_ind 
Jan 7 10:00:23.927: vtsp_do_call_setup_ind: Call ID=65579, guid=62031A88 
Jan 7 10:00:23.927: vtsp_do_call_setup_ind: type=0, under_spec=0, 
name=, id0=0, id1=0,id2=0, calling=, called= 
Jan 7 10:00:23.927: vtsp_do_call_setup_ind: redirect DN =  reason = 
 0vtsp_do_r2_start_digit(): fsm_push(vtsp_r2_state_table)

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp (vdev_info=0x61F19688, 
vtsp_cdb=0x61B5BFF8)
Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:vdev_common 
BP TS allocatedat BP_stream0,
 BP_Ch8 
Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:DST_tdm_chnl call. 
BP TS allocatedat stream
 5, chan 13,BP_stream 255, BP_ch 15 
Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:DST_tdm_chnl call. 
BP TS allocatedat stream
 5, chan 13,BP_stream 0, BP_ch 8 
Jan 7 10:00:23.927: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK 
(DNIS=, ANI=) at slot 1, port 60 

Jan 7 10:00:23.931: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE: R2_IN_IDLE 
R2 Got Event R2_START 
Jan 7 10:00:24.027: CSM_RX_CAS_EVENT_FROM_NEAT:(0007):  EVENT_START_RX_TONE 
at slot 1 and port 60 
Jan 7 10:00:24.027: from NEAT(0): (0/8): TX SEIZURE_ACK 
(ABCD=1101)dc_init_dsp
 vtsp_open_voice_and_set_params 
Jan 7 10:00:24.151: dsp_close_voice_channel: [0:1:8] packet_Len=8 channel_id=4929 
 packet_id=75 
Jan 7 10:00:24.151: dsp_open_voice_channel_20: [0:1:8] packet_Len=16 
channel_id=4929 
 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 
time_slot=0 serial_port=0 
Jan 7 10:00:24.151: dsp_encap_config_20: [0:1:8] packet_Len=24 channel_id=4929 
 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 
Jan 7 10:00:24.151: dsp_set_playout: [0:1:8] packet_Len=18 channel_id=4929 
 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300 
Jan 7 10:00:24.151: dsp_echo_canceller_control: [0:1:8] 
packet_Len=10 channel_id=4929
 packet_id=66 flags=0x0
Jan 7 10:00:24.151: dsp_set_gains: [0:1:8] packet_Len=12 
channel_id=4929 packet_id=91
 in_gain=0 out_gain=0 
Jan 7 10:00:24.151: dsp_vad_enable: [0:1:8] packet_Len=10 
channel_id=4929 packet_id=78
 thresh=-38
Jan 7 10:00:24.151: dsp_voice_mode: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=73
 coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64 
comfort_noise=1 
inband_detect=1 digit_relay=2 AGC_flag=0dsp_dtmf_mode
(VTSP_TONE_R2_MF_FORWARD_MODE) 

Jan 7 10:00:24.151: dsp_dtmf_mode: [0:1:8] packet_Len=10 channel_id=4929 
packet_id=65dtmf_or_mf=1

!--- Digit 5 is sent: Forward Signal Group I-5 (First DNIS digit).

Jan 7 10:00:24.203: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=5,
 rtp_timestamp=0x04030000 dc_digit_up
Jan 7 10:00:24.203: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)received digit (5)
Jan 7 10:00:24.203: CSM voice (1/60): Rcvd Digit detected(5)
Jan 7 10:00:24.203: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_PRE_CALLERID R2
 Got Event 5

!--- Send Backward Signal Group A-5 (caller category request).

Jan 7 10:00:24.203: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5
Jan 7 10:00:24.203: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929packet_id=90
 string=5 digits=1, time_on=65435, time_off=30
Jan 7 10:00:24.203:    digit=, components=2, freq_of_first=1020, 
freq_of_second=780,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:24.303: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=5,
 duration=30dc_digit
Jan 7 10:00:24.303: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (5)
Jan 7 10:00:24.303: CSM voice (1/60): Rcvd Digit detected(5)
Jan 7 10:00:24.303: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID R2
 Got Event R2_TONE_OFF

Jan 7 10:00:24.303: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
string=5dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #
Jan 7 10:00:24.303: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929
 packet_id=90 string=# digits=1, time_on=150, time_off=30
Jan 7 10:00:24.303:    digit=, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1

!--- Caller Category Forward Signal Group II-1 is sent.

Jan 7 10:00:24.403: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,
 rtp_timestamp=0x001E0010 dc_digit_up
Jan 7 10:00:24.403: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)received 
digit (1)
Jan 7 10:00:24.403: CSM voice (1/60): Rcvd Digit detected(1)
Jan 7 10:00:24.403: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2
 Got Event 1

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.403: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
string=5dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5
Jan 7 10:00:24.403: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=5 digits=1, time_on=65435, time_off=30
Jan 7 10:00:24.403:    digit=, components=2, freq_of_first=1020, freq_of_second=780,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:24.503: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,
 duration=30dc_digit
Jan 7 10:00:24.503: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1)
Jan 7 10:00:24.503: CSM voice (1/60): Rcvd Digit detected(1)
Jan 7 10:00:24.503: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID R2
 Got Event R2_TONE_OFF
Jan 7 10:00:24.503: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
string=5dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #
Jan 7 10:00:24.503: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=# digits=1, time_on=150, time_off=30
Jan 7 10:00:24.503:    digit=, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1

!--- First ANI digit is sent: Forward Signal Group I-1.

Jan  7 10:00:24.603: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:
digit=1, rtp_timestamp=0x001E0010 dc_digit_up
Jan 7 10:00:24.603: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (1)
Jan 7 10:00:24.603: CSM voice (1/60): Rcvd Digit detected(1)
Jan 7 10:00:24.603: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID R2
 Got Event 1

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.603: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.603: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=5 digits=1, time_on=65435, time_off=30
Jan 7 10:00:24.603:    digit=, components=2, freq_of_first=1020, 
freq_of_second=780,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:24.703: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,
 duration=30dc_digit
Jan 7 10:00:24.703: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1)
Jan 7 10:00:24.703: CSM voice (1/60): Rcvd Digit detected(1)
Jan 7 10:00:24.703: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID R2
 Got Event R2_TONE_OFF
Jan 7 10:00:24.703: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #
Jan 7 10:00:24.703: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=# digits=1, time_on=150, time_off=30
Jan 7 10:00:24.703:    digit=, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1

!--- Second ANI digit is sent: Forward Signal Group I-2.

Jan 7 10:00:24.803: vtsp_process_dsp_message: 
MSG_TX_DTMF_DIGIT_BEGIN:digit=2,
 rtp_timestamp=0x001E0010 dc_digit_up
Jan 7 10:00:24.803: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) 
received digit (2)
Jan 7 10:00:24.803: CSM voice (1/60): Rcvd Digit detected(2)
Jan 7 10:00:24.803: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID R2
 Got Event 2

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.803: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.803: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929packet_id=90
 string=5 digits=1, time_on=65435, time_off=30
Jan 7 10:00:24.803:    digit=, components=2, freq_of_first=1020, 
freq_of_second=780,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:24.903: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=2,
 duration=30dc_digit
Jan 7 10:00:24.903: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (2)
Jan 7 10:00:24.903: CSM voice (1/60): Rcvd Digit detected(2)
Jan 7 10:00:24.903: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID
 R2 Got Event R2_TONE_OFF
Jan 7 10:00:24.903: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #
Jan 7 10:00:24.903: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=# digits=1, time_on=150, time_off=30
Jan 7 10:00:24.903:    digit=, components=2, freq_of_first=0, 
freq_of_second=0,
 amp_of_first=1, amp_of_second=1

!--- Third ANI digit is sent: Forward Signal Group I-3.

Jan 7 10:00:25.003: vtsp_process_dsp_message: 
MSG_TX_DTMF_DIGIT_BEGIN: digit=3,
 rtp_timestamp=0x001E0010 dc_digit_up
Jan 7 10:00:25.003: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) 
received digit (3)
Jan 7 10:00:25.003: CSM voice (1/60): Rcvd Digit detected(3)
Jan 7 10:00:25.003: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID R2
 Got Event 3

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:25.003: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5
 
Jan 7 10:00:25.003: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=5 digits=1, time_on=65435, time_off=30
Jan 7 10:00:25.003:    digit=, components=2, freq_of_first=1020, 
freq_of_second=780,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:25.103: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=3,
 duration=30dc_digit
Jan 7 10:00:25.103: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (3)
Jan 7 10:00:25.103: CSM voice (1/60): Rcvd Digit detected(3)
Jan 7 10:00:25.103: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID R2
 Got Event R2_TONE_OFF
Jan 7 10:00:25.103: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #
Jan 7 10:00:25.103: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=# digits=1, time_on=150, time_off=30
Jan 7 10:00:25.103:    digit=, components=2, freq_of_first=0, 
freq_of_second=0,
 amp_of_first=1, amp_of_second=1

!--- Digit 15 is sent: Forward Signal Group I-15 (end of ANI digit).

Jan 7 10:00:25.203: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: 
digit=15,
 rtp_timestamp=0x001E0010 dc_digit_up
Jan 7 10:00:25.203: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) 
received digit (*)
Jan 7 10:00:25.203: CSM voice (1/60): Rcvd Digit detected(*)
Jan 7 10:00:25.203: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CALLERID R2
 Got Event 15

!--- Send Backward Signal Group A-1 (next DNIS digit).

Jan 7 10:00:25.203: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1
Jan 7 10:00:25.203: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=1 digits=1, time_on=65435, time_off=30
Jan 7 10:00:25.203:    digit=, components=2, freq_of_first=1020, 
freq_of_second=1140,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:25.303: vtsp_process_dsp_message: 
MSG_TX_DTMF_DIGIT_OFF: digit=15,
 duration=30dc_digit
Jan 7 10:00:25.303: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (*)
Jan 7 10:00:25.303: CSM voice (1/60): Rcvd Digit detected(*)
Jan 7 10:00:25.303: R2 Incoming Voice(1/60): DSX (E1 0:8):
 STATE:R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF
Jan 7 10:00:25.303: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
 string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #
Jan 7 10:00:25.303: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929
 packet_id=90 string=# digits=1, time_on=150, time_off=30
Jan 7 10:00:25.303:    digit=, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1

!--- Second DNIS digit is sent: Forward Signal Group I-6.

Jan  7 10:00:25.391: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=6,
 rtp_timestamp=0x001E0010 dc_digit_up
Jan 7 10:00:25.391: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) 
received digit (6)
Jan 7 10:00:25.391: CSM voice (1/60): Rcvd Digit detected(6)
Jan 7 10:00:25.391: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_COLLECT_DNIS
 R2 Got Event 6

!--- Send Backward Signal Group A-1.

Jan 7 10:00:25.391: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
string=56dc_dial()
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1

Jan 7 10:00:25.391: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=1 digits=1, time_on=65435, time_off=30
Jan 7 10:00:25.391:    digit=, components=2, freq_of_first=1020, 
freq_of_second=1140,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:25.491: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=6,
 duration=30dc_digit
Jan 7 10:00:25.491: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (6)
Jan 7 10:00:25.491: CSM voice (1/60): Rcvd Digit detected(6)
Jan 7 10:00:25.491: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE: R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF
Jan 7 10:00:25.491: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
string=56dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #
Jan 7 10:00:25.491: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=# digits=1, time_on=150, time_off=30
Jan 7 10:00:25.491:    digit=, components=2, freq_of_first=0, 
freq_of_second=0,
 amp_of_first=1, amp_of_second=1

!--- Third DNIS digit is sent: Forward Signal Group I-7.

Jan 7 10:00:25.583: vtsp_process_dsp_message: 
MSG_TX_DTMF_DIGIT_BEGIN: digit=7,
 rtp_timestamp=0x001E0010 dc_digit_up
Jan 7 10:00:25.583: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) 
received digit (7)
Jan 7 10:00:25.583: CSM voice (1/60): Rcvd Digit detected(7)
Jan 7 10:00:25.583: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event 7

!--- Send Backward Signal Group A-1.

Jan 7 10:00:25.583: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
 string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1

Jan 7 10:00:25.583: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=1 digits=1, time_on=65435, time_off=30
Jan 7 10:00:25.583:    digit=, components=2, freq_of_first=1020, 
freq_of_second=1140,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:25.683: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7,
 duration=30dc_digit
Jan 7 10:00:25.683: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) 
received digit (7)
Jan 7 10:00:25.683: CSM voice (1/60): Rcvd Digit detected(7)
Jan 7 10:00:25.683: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_OFF
Jan 7 10:00:25.683: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
 string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #
Jan 7 10:00:25.683: dsp_dtmf_dialing: [0:1:8] packet_Len=24 
channel_id=4929 packet_id=90
 string=# digits=1, time_on=150, time_off=30
Jan 7 10:00:25.683:    digit=, components=2, freq_of_first=0, 
freq_of_second=0,
 amp_of_first=1, amp_of_second=1
Jan 7 10:00:25.835: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()

!--- Timeout is 3 seconds.

Jan 7 10:00:28.583: R2 Incoming Voice(1/60): DSX (E1 0:8):
 STATE:R2_IN_COLLECT_DNIS R2
 Got Event R2_TONE_TIMER

!--- Send Backward Signal Group A-3: address-complete, changeover 
!--- to reception of group-B signal.

Jan 7 10:00:28.583: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,
 string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 3#
Jan 7 10:00:28.583: dsp_dtmf_dialing: [0:1:8] packet_Len=36 
channel_id=4929 packet_id=90
 string=3# digits=2, time_on=150, time_off=30
Jan 7 10:00:28.583:    digit=, components=2, freq_of_first=1020, 
freq_of_second=900,
 amp_of_first=8192, amp_of_second=8192
Jan 7 10:00:28.583:    digit=, components=2, freq_of_first=0, freq_of_second=0,
 amp_of_first=1, amp_of_second=1

!--- Forward Signal Group II-1 is sent: subscriber without priority.

Jan 7 10:00:28.831: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,
 rtp_timestamp=0x001E0003 dc_digit_up
Jan 7 10:00:28.831: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) 
received digit (1)
Jan 7 10:00:28.831: CSM voice (1/60): Rcvd Digit detected(1)
Jan 7 10:00:28.831: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_CATEGORY R2
 Got Event 1
Jan 7 10:00:28.831: CSM_PROC_IC1_COLLECT_ADDR_INFO: 
CSM_EVENT_ADDR_INFO_COLLECTED
(DNIS=567, ANI=123) at slot 1, port 60
Jan 7 10:00:28.831: vtsp_tsp_call_accept_check (sdb=0x61DADEE0, 
calling_number=123
 called_number=567): peer_tag=0
Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device
Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate
 a non-idle modem
Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device
Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate 
a non-idle modem
Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device
Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate 
a non-idle modem
Jan 7 10:00:28.835: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK 
at slot 1,
 port 60
Jan 7 10:00:28.835: vtsp_IC_switch : (voice_vdev= 0x61F19688)
Jan 7 10:00:28.835: vtsp_tsp_call_switch_ind (cdb=0x61B5BFF8, 
tsp_info=0x61F19688,
 calling_number=123 called_number=567 redirect_number=):
peer_tag=123dc_switch: fsm_pop()
Jan 7 10:00:28.835: vtsp_do_call_setup_ind
Jan 7 10:00:28.835: vtsp_do_call_setup_ind: Call ID=65581, 
guid=62031A88
Jan 7 10:00:28.835: vtsp_do_call_setup_ind: type=0, under_spec=0, 
name=b`, id0=9,
 id1=0, id2=0, calling=123, called=567
Jan 7 10:00:28.835: dsp_cp_tone_off: [] packet_Len=8 channel_id=4929 
packet_id=71
Jan 7 10:00:28.835: dsp_idle_mode: [] packet_Len=8 channel_id=4929 
packet_id=68
Jan 7 10:00:28.835: dsp_close_voice_channel: [] packet_Len=8 
channel_id=4929 packet_id=75
Jan 7 10:00:28.835: vtsp_timer_stop: 7063006
Jan 7 10:00:28.839: csm_vtsp_call_setup_resp (vdev_info=0x61F19688, 
vtsp_cdb=0x61B5BFF8)
Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:vdev_common BP TS 
allocatedat BP_stream0,
 BP_Ch8
Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:DST_tdm_chnl call.
 BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch 8
Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:DST_tdm_chnl call.
 BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch 
8vtsp_open_voice_and_set_params
Jan 7 10:00:28.839: dsp_close_voice_channel: [0:1 (17)] 
packet_Len=8 channel_id=4929
 packet_id=75
Jan 7 10:00:28.839: dsp_open_voice_channel_20: [0:1 (17)] packet_Len=16 
channel_id=4929
 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 
time_slot=0 serial_port=0
Jan 7 10:00:28.839: dsp_encap_config_20: [0:1 (17)] packet_Len=24 
channel_id=4929
 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0t_vpxcc=0x0 
r_vpxcc=0x0
Jan 7 10:00:28.839: dsp_set_playout: [0:1 (17)] packet_Len=18 
channel_id=4929 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300
Jan 7 10:00:28.839: dsp_echo_canceller_control: [0:1 (17)] 
packet_Len=10 channel_id=4929
 packet_id=66 flags=0x0
Jan 7 10:00:28.839: dsp_set_gains: [0:1 (17)] packet_Len=12 
channel_id=4929 packet_id=91
 in_gain=0 out_gain=0
Jan 7 10:00:28.839: dsp_vad_enable: [0:1 (17)] packet_Len=10 
channel_id=4929 packet_id=78
 thresh=-38act_proceeding
Jan 7 10:00:28.839: csm_vtsp_call_proceeding:DST_tdm_chnl call. 
BP TS allocatedstream 5,
 chan 13,BP_stream 0, BP_ch 8act_alert
Jan 7 10:00:28.867: vtsp_ring_noan_timer_start: 7063009 
Jan 7 10:00:28.867: csm_vtsp_call_alert (vtsp_cdb=0x61B5BFF8)
Jan 7 10:00:28.867:  csm_vtsp_call_alert: CSM_EVENT_ALERTING_RECEIVED
Jan 7 10:00:28.867: CSM_IC5_WAIT_FOR_SWITCH_OVER:  at slot 1, port 60
Jan 7 10:00:28.867: CSM_EVENT_ALERTING_RECEIVED:
Jan 7 10:00:28.867:  calling alerting_start_event

!--- Note: For modems, Backward Signal 
!--- Group B-6 (subscriber's line free, charge)
!--- is sent immediately. 
!--- For voice, it is delayed until alerting is received.
!--- Notice that "R2_REJECT" is printed instead of R2_ALERTING.
!--- This printing issue is solved in Cisco IOS Software Release 12.1T.

Jan 7 10:00:28.867: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE:R2_IN_IDLE R2
 Got Event R2_REJECT
Jan 7 10:00:28.867:  R2_ALERTING: r2_comp_idle
Jan 7 10:00:28.867: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
string=567act_bridge
Jan 7 10:00:28.867: dsp_voice_mode: [0:1 (17)] packet_Len=24 
channel_id=4929 packet_id=73
 coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64 
comfort_noise=1
 inband_detect=1 digit_relay=2 AGC_flag=0dsp_dtmf_mode 
(VTSP_TONE_R2_MF_FORWARD_MODE)

!--- Answer signal (B-6) is sent after alerting is received. 
!--- Send Backward Signal Group B6 signal (Subscriber's line free, charge).

Jan 7 10:00:28.871: dsp_dtmf_mode: [0:1 (17)] packet_Len=10 
channel_id=4929 packet_id=65
 dtmf_or_mf=1vtsp_r2_dial vtsp_r2_dial(): fsm_push(vtsp_r2_state_table)
 dsp_dtmf_dialing(): dial_string = 6

Jan 7 10:00:28.871: dsp_dtmf_dialing: [0:1 (17)] packet_Len=24 
channel_id=4929 
 packet_id=90 string=6 digits=1, time_on=65435, time_off=30 
Jan 7 10:00:28.871:    digit=, components=2, freq_of_first=900, 
freq_of_second=780,
 amp_of_first=8192, amp_of_second=8192 
Jan 7 10:00:28.923: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,
 rtp_timestamp=0x001E0006 dc_digit_up 
Jan 7 10:00:28.923: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) 
received digit (1) 
Jan 7 10:00:28.923: CSM voice (1/60): Rcvd Digit detected(1) 
Jan 7 10:00:28.923: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE: R2_IN_COMPLETE
 R2 Got Event 1 
Jan 7 10:00:28.971: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,
 duration=30dc_digit 
Jan 7 10:00:28.971: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) 
received digit (1) 
Jan 7 10:00:28.971: CSM voice (1/60): Rcvd Digit detected(1)
Jan 7 10:00:28.971: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE: R2_IN_COMPLETE R2
 Got Event R2_TONE_OFF 
Jan 7 10:00:28.971: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, 
string=567dc_dial() 
 vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # 
Jan 7 10:00:28.971: dsp_dtmf_dialing: [0:1 (17)] packet_Len=24 
channel_id=4929 
 packet_id=90 string=# digits=1, time_on=150, time_off=30 
Jan 7 10:00:28.975:    digit=, components=2, freq_of_first=0, 
freq_of_second=0,
 amp_of_first=1, amp_of_second=1ds_dialing_defaultds_dialing_default 
Jan 7 10:00:29.127: vtsp_process_dsp_message: 
MSG_TX_DIALING_DONEdc_dialing_done() 
Jan 7 10:00:29.971: R2 Incoming Voice(1/60): DSX (E1 0:8): 
STATE: R2_IN_WAIT_GUARD R2
 Got Event R2_TONE_TIMER 
Jan 7 10:00:29.971:  R2_IN_IDLE:2 r2_in_connect called 
Jan 7 10:00:29.971: R2_IN_CONNECT: call end dial 
Jan 7 10:00:29.971:  pop the dial state machine 
Jan 7 10:00:29.971: vtsp_r2_end_dial: vdev_common=0x6205E5F8, 
string=567ds_end_dial(): 
 fsm_pop() act_caps_ind 
Jan 7 10:00:29.971: act_caps_ind:Encap 1, Vad 2, Codec 0x4, 
CodecBytes 20, FaxRate 2,
 FaxBytes 20 SignalType 0 DtmfRelay 1, Modem 1act_caps_ack 
Jan 7 10:00:29.971: dsp_idle_mode: [0:1 (17)] packet_Len=8 
channel_id=4929 packet_id=68 
Jan 7 10:00:29.971: act_caps_ack: codec = 15, ret = 1
Jan 7 10:00:29.971: dsp_cp_tone_off: [0:1 (17)] packet_Len=8 
channel_id=4929 packet_id=71 
Jan 7 10:00:29.971: dsp_idle_mode: [0:1 (17)] packet_Len=8 
channel_id=4929 packet_id=68 
Jan 7 10:00:29.971: dsp_encap_config_20: [0:1 (17)] packet_Len=24 
channel_id=4929 
 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 
r_vpxcc=0x0 
Jan 7 10:00:29.971: dsp_voice_mode: [0:1 (17)] packet_Len=24 
channel_id=4929 packet_id=73
 coding_type=19 voice_field_size=20 VAD_flag=1 echo_length=64 
comfort_noise=1
 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect 
Jan 7 10:00:30.255: vtsp_ring_noan_timer_stop: 7063148 
Jan 7 10:00:30.255: dsp_cp_tone_off: [0:1 (17)] packet_Len=8 
channel_id=4929 packet_id=71 
Jan 7 10:00:30.255: csm_vtsp_call_connect (vtsp_cdb=0x61B5BFF8, 
voice_vdev=0x61F19688) 
Jan 7 10:00:30.255: CSM_IC5_WAIT_FOR_SWITCH_OVER: 
CSM_EVENT_MODEM_OFFHOOK at slot 1,
 port 60 
Jan 7 10:00:30.607: CSM_RX_CAS_EVENT_FROM_NEAT:(0007):  
EVENT_CHANNEL_CONNECTED at slot 1
 and port 60 
Jan 7 10:00:30.607: CSM_PROC_IC6_WAIT_FOR_CONNECT: 
CSM_EVENT_DSX0_CONNECTED at slot 1,
 port 60 
Jan 7 10:00:30.607: from NEAT(0): (0/8): TX ANSWERED (ABCD=0101) 
eefje# 

Discussões relacionadas da comunidade de suporte da Cisco

A Comunidade de Suporte da Cisco é um fórum onde você pode perguntar e responder, oferecer sugestões e colaborar com colegas.


Informações Relacionadas


Document ID: 12154