WAN : Point-to-Point Protocol (PPP)

Using PPP Half-Bridging to Connect Routed and Bridged Networks (Utilizando meia conexão por ponte PPP para conectar redes roteadas e conectadas por ponte)

19 Setembro 2015 - Tradução por Computador
Outras Versões: Versão em PDFpdf | Inglês (22 Agosto 2015) | Feedback


Índice


Introdução

Este documento fornece uma configuração de exemplo usando o PPP queconstrói uma ponte sobre para conectar roteado e redes interligada.

Pré-requisitos

Requisitos

Não existem requisitos específicos para este documento.

Componentes Utilizados

As informações neste documento são baseadas nestas versões de software e hardware:

  • Software Release 12.2(7b) de Cisco IOS�.

  • Dois Cisco 2500 Series Router. Cada um tem pelo menos uma relação do ISDN BRI.

As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. Todos os dispositivos utilizados neste documento foram iniciados com uma configuração (padrão) inicial. Se a sua rede estiver ativa, certifique-se de que entende o impacto potencial de qualquer comando.

Produtos Relacionados

Esta configuração também pode ser utilizada com estas versões de hardware e software:

  • Alguma interface serial, tal como a série, Basic Rate Interface (BRI), relação da taxa principal (PRI), e assim por diante.

  • Cisco IOS Software Release 11.2.

  • Algum Cisco IOS Software running do roteador como mencionado acima, e pelo menos uma porta ISDN-BRI. Contudo, os recursos de semiBridge podem ser usados em um roteador com uma interface serial.

Convenções

Para obter mais informações sobre convenções de documento, consulte as Convenções de dicas técnicas Cisco.

Informações de Apoio

A ponte envia pacotes de ponte para a meia-ponte PPP que os converte em pacotes roteados e os encaminha para outros processos do roteador. Igualmente, o semibridge PPP converte pacotes roteado aos pacotes do bridge Ethernet, e envia-os à ponte na mesma sub-rede de Ethernet.

Nota: Esta configuração não cobre um bridge direta em ambos os lados. Para tal configuração refira o documento do Bridging através de ISDN.

Esteja ciente que construir uma ponte sobre em uma conexão ISDN tende a manter muito a conexão ativa por períodos longos, se não permanentemente. Se o telco carrega para o ISDN baseado no tempo de conexão, este pode conduzir a uma conta muito grande. Consequentemente, esta encenação é recomendada para aquelas que têm linhas ISDN de uso ilimitado.

Nota: Uma relação não pode funcionar como um semibridge e uma ponte. O Cisco IOS Software apoia não mais de um semibridge PPP pela sub-rede de Ethernet.

Configurar

Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.

Nota: Para localizar informações adicionais sobre os comandos usados neste documento, utilize a Ferramenta Command Lookup (somente clientes registrados).

Diagrama de Rede

Este documento utiliza a seguinte configuração de rede:

/image/gif/paws/10381/ppp_half_bridging.gif

Configurações

Este documento utiliza as seguintes configurações:

  • Venus

    Este roteador é configurado como um bridge direta com Roteamento IP desabilitou. Os seletores do dispositivo quando todo o tráfego interligado chegar.

  • Saturn

    Este roteador foi configurado como um semibridge. Note que os comandos dialer string, dialer group, e dialer list não estão configurados neste lado. Assim este roteador nunca discará, mas aceitará chamadas recebidas. Isto impede que o roteador disque o roteador remoto. Nós giramos Roteamento IP sobre aqui. O software de Bridging completo não é configurado neste roteador. O semibridge PPP está sendo executado na interface BRI, assim que os comandos como a mostra constroem uma ponte sobre e a medir-árvore da mostra não rende nenhuma saída neste roteador.

Venus
Venus#show running-config
!
version 12.2
!
hostname Venus
!
username Saturn password 0 same 

!--- Required for PPP CHAP authentication during dialup

ip subnet-zero
no ip routing 

!--- Turn off routing

no ip domain-lookup
!
isdn switch-type basic-5ess

!--- The ISDN switchtype for this circuit. Obtain this information from the 
!--- Telco. This ISDN switch type is USA specific and could be changed          
!--- depending on the country and TELCO requirements

!
interface Ethernet0
ip address 10.1.1.2 255.0.0.0 

!--- This is for management purpose only

no ip route-cache
no ip mroute-cache
bridge-group 1

!--- Assign this interface to Bridge Group 1
!--- Frames are bridged only among interfaces in the same group
!--- Note: the dialer1 interface is also in this bridge-group 1

interface BRI0
no ip address
no ip route-cache
no ip mroute-cache
dialer pool-member 1  

!--- Dialer profiles configured with same dialer pool #
!--- (in this case, dialer1) will bind to this interface

isdn switch-type basic-5ess

!--- Check with your Telco for the correct values

!
interface Dialer1 

!--- Configure the Dialer profile

description ISDN to Saturn
ip address 10.1.1.2 255.0.0.0
encapsulation ppp
dialer pool 1

!--- Use physical interfaces configured with same pool # 
!--- (in this case, bri0) during dialup

dialer remote-name Saturn 

!--- Specifies remote CHAP name

dialer string 5552000 

!--- Specifies the number to dial when interesting traffic arrives

dialer-group 1 

!--- Defines the interesting traffic as configured in the dialer-list

ppp authentication chap 

!--- Use CHAP as the authentication method

bridge-group 1 

!--- Assign this interface to Bridge Group 1.
!--- Frames are bridged only among interfaces in the same group.
!--- Note: the Ethernet interface 0 is also in this bridge-group 1


ip default-gateway 10.1.1.3      

!--- All default traffic from Venus should go through Saturn

dialer-list 1 protocol bridge permit 

!--- Defines the interesting traffic. In this case, all bridged traffic

bridge 1 protocol ieee

!--- Define the type of Spanning-Tree Protocol used for the interface in
!--- bridge-group 1. Here we use the IEEE spanning tree protocol. The IEEE 802.1D
!--- Spanning-Tree Protocol is the preferred way of running the bridge.

!

Saturn
Saturn#show running-config
!
version 12.2
!
hostname Saturn
!
username Venus password 0 same 

!--- Required for PPP CHAP authentication during dialup

ip subnet-zero
no ip domain-lookup
!
isdn switch-type basic-5ess

!--- The ISDN switchtype for this circuit. Obtain this information from the 
!--- Telco. This ISDN switch type is USA specific and could be changed          
!--- depending on the country and Telco requirements

!
interface Ethernet0
ip address 192.168.1.1 255.255.0.0
!
interface BRI0
no ip address
no ip mroute-cache
dialer pool-member 1

!--- Dialer profiles configured with same dialer pool #
!--- (in this case, dialer1) will bind to this interface

isdn switch-type basic-5ess
!
interface Dialer1 

!--- Configure the Dialer profile

description ISDN to Venus
ip address 10.1.1.3 255.0.0.0 

!--- IP address is required to route the bridged traffic from Venus
!--- This ip address MUST be in the same subnet as the remote bridge network

encapsulation ppp 
dialer pool 1

!--- Use physical interfaces configured with same pool # 
!--- (in this case, bri0) during dialup

dialer remote-name Venus
pulse-time 0
ppp bridge ip 

!--- Configures half bridge 

ppp authentication chap                                                          

!--- Use CHAP as the authentication method

!

Verificar

Esta seção fornece informações que você pode usar para confirmar se sua configuração está funcionando adequadamente.

A Output Interpreter Tool (somente clientes registrados) oferece suporte a determinados comandos show, o que permite exibir uma análise da saída do comando show.

  • status de ISDN da mostra — indica o estado L1, L2, e L3 das interfaces.

  • discador da mostra — indica o estado do discador, e o status individual dos canais ISDN.

  • ponte da mostra — classes dos indicadores de entradas no Bridge Forwarding Database, no modo de exec privilegiado.

  • relação da mostra — indica o estado de várias relações, incluindo a série e as interfaces BRI.

  • a mostra arp — verifica o mapeamento ARP. O ARP é um protocolo usado para traçar o endereço da camada 2 (MAC address) a um endereço da camada 3 (endereço IP de Um ou Mais Servidores Cisco ICM NT).

  • medir-árvore da mostra — indica a topologia de Spanning Tree conhecida ao roteador.

Comandos show em Venus após discagem para Saturn

Venus#show isdn status
Global ISDN Switchtype = basic-5ess
ISDN BRI0 interface
        dsl 0, interface ISDN Switchtype = basic-5ess
    Layer 1 Status:
        ACTIVE
    Layer 2 Status:
        TEI = 107, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
        1 Active Layer 3 Call(s)
        CCB:callid=800E, sapi=0, ces=1, B-chan=2, calltype=DATA    
Active dsl 0 CCBs = 1
    The Free Channel Mask:
  0x80000001
    Number of L2 Discards = 0, L2 Session ID = 17
    Total Allocated ISDN CCBs = 1
Venus#show dialer
BRI0 - dialer type = ISDN

Dial String Successes Failures Last DNIS Last status
   0 incoming call(s) have been screened.
   0 incoming call(s) rejected for callback.

BRI0:1 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is idle

BRI0:2 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up
   Dial reason: bridge (0x0800)
   Interface bound to profile Di1
   Time until disconnect 90 secs
   Current call connected 00:00:31

Di1 - dialer type = DIALER PROFILE
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up
   Number of active calls = 1
   Dial String Successes Failures Last DNIS	 Last status
   5552000   5   1   00:00:34  Successful Default

Venus#show interface bri0:2
   BRI0:2 is up, line protocol is up
   Hardware is BRI
   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   Keepalive set (10 sec)
   Time to interface disconnect: idle 00:01:18
   Interface is bound to Di1 (Encapsulation PPP)
   LCP Open
   Closed: IPCP
   Open: BRIDGECP, CDPCP                     
   
!--- Bridge Control Protocol is open

   Last input 00:00:42, output 00:00:00, output hang never
   Last clearing of "show interface" counters never
   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
   Queueing strategy: fifo
   Output queue :0/40 (size/max)
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
   161 packets input, 9796 bytes, 0 no buffer
   Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
   0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
   328 packets output, 16659 bytes, 0 underruns
   0 output errors, 0 collisions, 7 interface resets
   0 output buffer failures, 0 output buffers swapped out
   16 carrier transitions
Venus#show bridge
Total of 300 station blocks, 298 free
   Codes: P - permanent, S - self

Bridge Group 1:

 Address Action Interface Age RX count TX count
   00d0.58ad.ae13 forward Ethernet0 0 74 58
   0060.5cf4.a955 forward Dialer1 0 58 72

Venus#show arp
   Protocol Address Age (min) Hardware Addr Type Interface
   Internet 10.1.1.2 - 0060.5cf4.a9a8 ARPA Ethernet0
   Internet 10.1.1.3 0 0060.5cf4.a955 ARPA Dialer1

Venus#show spanning-tree
 
Bridge group 1 is executing the ieee compatible Spanning Tree protocol
   Bridge Identifier has priority 32768, address 0060.5cf4.a9a8
   Configured hello time 2, max age 20, forward delay 15
   Current root has priority 32768, address 0009.7c2e.ba00
   Root port is 2 (Ethernet0), cost of root path is 100
   Topology change flag not set, detected flag not set
   Number of topology changes 1 last change occurred 22:09:28 ago
   from Ethernet0
   Times: hold 1, topology change 35, notification 2
   hello 2, max age 20, forward delay 15
   Timers: hello 0, topology change 0, notification 0, aging 300
 
Port 2 (Ethernet0) of Bridge group 1 is forwarding
   Port path cost 100, Port priority 128, Port Identifier 128.2.
   Designated root has priority 32768, address 0009.7c2e.ba00
   Designated bridge has priority 32768, address 0009.7c2e.ba00
   Designated port id is 128.13, designated path cost 0
   Timers: message age 2, forward delay 0, hold 0
   Number of transitions to forwarding state: 1
   BPDU: sent 1, received 39911

 Port 8 (Dialer1) of Bridge group 1 is forwarding
   Port path cost 17857, Port priority 128, Port Identifier 128.8.
   Designated root has priority 32768, address 0009.7c2e.ba00
   Designated bridge has priority 32768, address 0060.5cf4.a9a8
   Designated port id is 128.8, designated path cost 100
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 1
   BPDU: sent 39879, received 0

Comandos show em discagens Saturn After Venus

Saturn#show dialer
BRI0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
   0 incoming call(s) have been screened.

   0 incoming call(s) rejected for callback.

BRI0:1 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is idle

BRI0:2 - dialer type = ISDN
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up
   Interface bound to profile Di1
   Time until disconnect 45 secs
   Connected to <unknown phone number> (Venus)

Di1 - dialer type = DIALER PROFILE
   Idle timer (120 secs), Fast idle timer (20 secs)
   Wait for carrier (30 secs), Re-enable (15 secs)
   Dialer state is data link layer up   Number of active calls = 1

Dial String Successes Failures Last DNIS Last status

Saturn#show isdn status
   Global ISDN Switchtype = basic-5ess
   ISDN BRI0 interface
   dsl 0, interface ISDN Switchtype = basic-5ess
   Layer 1 Status:
   ACTIVE
   Layer 2 Status:
   TEI = 105, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
   I_Queue_Len 0, UI_Queue_Len 0
   Layer 3 Status:
   1 Active Layer 3 Call(s)
   CCB:callid=2B, sapi=0, ces=1, B-chan=2, calltype=DATA
   Active dsl 0 CCBs = 1
   The Free Channel Mask: 0x80000001
   Number of L2 Discards = 0, L2 Session ID = 37
   Total Allocated ISDN CCBs = 1

Saturn#show arp
   Protocol Address Age (min) Hardware Addr Type Interface
   Internet 10.1.1.2 27 0060.5cf4.a9a8 ARPA Dialer1
   Internet 10.1.1.1 63 00d0.58ad.ae13 ARPA Dialer1
   Internet 192.168.1.1 - 0060.5cf4.a955 ARPA Ethernet0
   Internet 192.168.1.2 53 0000.0c76.2882 ARPA Ethernet0

Saturn#show spanning-tree
No spanning tree instances exist. 

!--- This router does not run full bridge, 
!--- so spanning tree does not run on this router


Saturn#show ip route
   Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
   D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
   N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
   E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
   i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
   * - candidate default, U - per-user static route, o - ODR
   P - periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, Dialer1 
C 192.168.0.0/16 is directly connected, Ethernet0

Troubleshooting

Esta seção fornece informações que podem ser usadas para o troubleshooting da sua configuração.

Troubleshooting de Recursos

Os procedimentos de Troubleshooting para chamadas ISDN entrantes e que parte são explicados na tecnologia dialup: Documento das técnicas de Troubleshooting. A informação adicional em como pesquisar defeitos edições da camada de ISDN 1, da camada 2 e da camada 3 é dada em usar o comando show isdn status para o Troubleshooting de BRI e pesquisar defeitos o ISDN BRI mergulham 3 usando o comando debug isdn q931.

Comandos para Troubleshooting

A Output Interpreter Tool (somente clientes registrados) oferece suporte a determinados comandos show, o que permite exibir uma análise da saída do comando show.

Nota: Antes de emitir comandos de depuração, consulte as informações importantes sobre eles.

  • debug dialer — indica quando o tráfego interessante esteve detectado, e quando discar está iniciado.

  • debug isdn event — indica a atividade de ISDN que ocorre no lado do usuário da interface, e é similar debugar o q931 de ISDN.

  • debugar o q931 de ISDN — fornece a informação sobre a configuração de chamada e desconexão das conexões de rede ISDN (camada 3), entre o roteador local (lado do usuário) e a rede.

  • debugar isdn q921 — indica os procedimentos de acesso da camada de link de dados (camada 2) que estão ocorrendo no roteador no canal D (LAPD) de sua interface.

  • debugar a negociação ppp — executa a negociação de opções de PPP e os parâmetros do protocolo network control (NCP).

  • debugar a autenticação de PPP — permite a troca de pacotes do protocolo challenge authentication (RACHADURA) e do protocolo password authentication (PAP).

Comandos Debug em Venus quando o tráfego interessante chegar

Venus#
*Mar  1 22:00:14.838: BR0 DDR: rotor dialout [priority]
*Mar  1 22:00:14.838: BR0 DDR: Dialing cause bridge (0x0800)
*Mar  1 22:00:14.842: BR0 DDR: Attempting to dial 5552000
*Mar  1 22:00:14.846: ISDN BR0: Outgoing call id = 0x8006, dsl 0
*Mar  1 22:00:14.846: ISDN BR0: Event: Call to 5552000 at 64 Kb/s
*Mar  1 22:00:14.850: ISDN BR0: process_bri_call(): call id 0x8006, 
called_number 5552000, speed 64, call type DATA
*Mar  1 22:00:14.854: CCBRI_Go Fr Host InPkgInfo (Len=22) :
*Mar  1 22:00:14.858: 1 0 1 80 6 0 4 2 88 90 18 1 83 2C 7 35 35 35 32 30 30 30
*Mar  1 22:00:14.866:
*Mar  1 22:00:14.870: CC_CHAN_GetIdleChanbri: dsl 0
*Mar  1 22:00:14.870:     Found idle channel B1
*Mar  1 22:00:14.886: ISDN BR0: TX -> INFOc sapi=0 tei=106 ns=0 nr=0 
i=0x08010605040288901801832C0735353532303030
*Mar  1 22:00:14.906:     SETUP pd = 8  callref = 0x06
*Mar  1 22:00:14.914:         Bearer Capability i = 0x8890
*Mar  1 22:00:14.918:         Channel ID i = 0x83
*Mar  1 22:00:14.92Venus#6:         Keypad Facility i = '5552000'
*Mar  1 22:00:15.190: ISDN BR0: RX <- INFOc sapi=0 tei=106 ns=0 nr=1 
i=0x0801860218018A
*Mar  1 22:00:15.198:     CALL_PROC pd = 8  callref = 0x86
*Mar  1 22:00:15.206:         Channel ID i = 0x8A
*Mar  1 22:00:15.222: ISDN BR0: TX -> RRr sapi=0 tei=106 nr=1
*Mar  1 22:00:15.230: CCBRI_Go Fr L3 pkt (Len=7) :
*Mar  1 22:00:15.230: 2 1 6 98 18 1 8A
*Mar  1 22:00:15.234:
*Mar  1 22:00:15.238: ISDN BR0: LIF_EVENT: ces/callid 1/0x8006 
HOST_PROCEEDING
*Mar  1 22:00:15.238: ISDN BR0: HOST_PROCEEDING
*Mar  1 22:00:15.242: ISDN BR0: HOST_MORE_INFO
*Mar  1 22:00:15.658: ISDN BR0: RX <- INFOc sapi=0 tei=106 ns=1 
nr=1 i=0x08018607
*Mar  1 22:00:15.666:     CONNECT pd = 8  callref = 0x86
*Mar  1 22:00:15.678: ISDN BR0: TX -> RRr sapi=0 tei=106 nr=2
*Mar  1 22:00:15.686: CCBRI_Go Fr L3 pkt (Len=4) :
*Mar  1 22:00:15.690: 7 1 6 91
*Mar  1 22:00:15.690:
*Mar  1 22:00:15.694: ISDN BR0: LIF_EVENT: ces/callid 1/0x8006 HOST_CONNECT
22:00:15: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
*Mar  1 22:00:15.702: BR0:2 PPP: Phase is DOWN, Setup [0 sess, 0 load]
*Mar  1 22:00:15.706: BR0:2 PPP: No remote authentication for call-out
*Mar  1 22:00:15.710: BR0:2 PPP: Phase is ESTABLISHING [0 sess, 0 load]
*Mar  1 22:00:15.710: BR0:2 PPP: Treating connection as a callout
*Mar  1 22:00:15.714: BR0:2 PPP: No remote authentication for call-out
*Mar  1 22:00:15.718: BR0:2 LCP: O CONFREQ [Closed] id 1 len 10
*Mar  1 22:00:15.722: BR0:2 LCP:    MagicNumber 0x6515B12A (0x05066515B12A)
*Mar  1 22:00:15.722: BR0:2: interface must be fifo queue, force fifo
22:00:15: %DIALER-6-BIND: Interface BR0:2 bound to profile Di1
*Mar  1 22:00:15.742: ISDN: get_isdn_service_state(): idb 0x1A2DBC bchan 3 
is_isdn 1 Not a Pri
*Mar  1 22:00:15.746: BR0:2 PPP: Treating connection as a callout
*Mar  1 22:00:15.746: ISDN BR0: Event: Connected to 5552000 on B2 at 64 Kb/s
*Mar  1 22:00:15.762: ISDN BR0: TX -> INFOc sapi=0 tei=106 ns=1 nr=2 i=0x0801060F
*Mar  1 22:00:15.766:     CONNECT_ACK pd = 8  callref = 0x06
*Mar  1 22:00:15.774: BR0:2 LCP: I CONFREQ [REQsent] id 1 len 15
*Mar  1 22:00:15.778: BR0:2 LCP:    AuthProto CHAP (0x0305C22305)
*Mar  1 22:00:15.782: BR0:2 LCP:    MagicNumber 0x788C6F8F (0x0506788C6F8F)
*Mar  1 22:00:15.786: BR0:2 LCP: O CONFACK [REQsent] id 1 len 15
*Mar  1 22:00:15.790: BR0:2 LCP:    AuthProto CHAP (0x0305C22305)
*Mar  1 22:00:15.790: BR0:2 LCP:    MagicNumber 0x788C6F8F (0x0506788C6F8F)
*Mar  1 22:00:15.798: BR0:2 LCP: I CONFACK [ACKsent] id 1 len 10
*Mar  1 22:00:15.798: BR0:2 LCP:    MagicNumber 0x6515B12A (0x05066515B12A)
*Mar  1 22:00:15.802: BR0:2 LCP: State is Open
*Mar  1 22:00:15.806: BR0:2 PPP: Phase is AUTHENTICATING, by the peer 
[0 sess, 1 load]
*Mar  1 22:00:15.870: ISDN BR0: RX <- RRr sapi=0 tei=106 nr=2
*Mar  1 22:00:15.882: BR0:2 CHAP: I CHALLENGE id 31 len 27 from "Saturn"
*Mar  1 22:00:15.890: BR0:2 CHAP: O RESPONSE id 31 len 26 from "Venus"
*Mar  1 22:00:15.914: BR0:2 CHAP: I SUCCESS id 31 len 4
*Mar  1 22:00:15.918: BR0:2 PPP: Phase is UP [0 sess, 1 load]
*Mar  1 22:00:15.922: BR0:2 BNCP: O CONFREQ [Closed] id 1 len 4
*Mar  1 22:00:15.926: BR0:2 IPCP: O CONFREQ [Closed] id 1 len 10
*Mar  1 22:00:15.930: BR0:2 IPCP:    Address 10.1.1.2 (0x03060A010102)
*Mar  1 22:00:15.934: BR0:2 CDPCP: O CONFREQ [Closed] id 1 len 4
*Mar  1 22:00:15.942: BR0:2 BNCP: I CONFREQ [REQsent] id 1 len 4
*Mar  1 22:00:15.946: BR0:2 BNCP: O CONFACK [REQsent] id 1 len 4
*Mar  1 22:00:15.950: BR0:2 CDPCP: I CONFREQ [REQsent] id 1 len 4
*Mar  1 22:00:15.954: BR0:2 CDPCP: O CONFACK [REQsent] id 1 len 4
*Mar  1 22:00:15.958: BR0:2 BNCP: I CONFACK [ACKsent] id 1 len 4
*Mar  1 22:00:15.958: BR0:2 BNCP: State is Open
*Mar  1 22:00:15.966: BR0:2 LCP: I PROTREJ [Open] id 2 len 16 protocol IPCP 
(0x80210101000A03060A010102)
*Mar  1 22:00:15.970: BR0:2 IPCP: State is Closed
*Mar  1 22:00:15.974: BR0:2 CDPCP: I CONFACK [ACKsent] id 1 len 4
*Mar  1 22:00:15.978: BR0:2 CDPCP: State is Open
*Mar  1 22:00:15.978: BR0:2 DDR: dialer protocol up
22:00:16: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, 
changed state to up
22:00:21: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 5552000
Venus#
Saturn#
4d16h: ISDN BR0: RX <- UI c/r=1 sapi=0 tei=127 
i=0x080141050402889018018A7008C135353532303030
4d16h:     SETUP pd = 8  callref = 0x41
4d16h:         Bearer Capability i = 0x8890
4d16h:         Channel ID i = 0x8A
4d16h:         Called Party Number i = 0xC1, '5552000', Plan:ISDN, 
Type:Subscriber(local)
4d16h: CCBRI_Go Fr L3 pkt (Len=21) :
4d16h: 5 1 C1 90 4 2 88 90 18 1 8A 70 8 C1 35 35 35 32 30 30 30
4d16h:
4d16h: ISDN BR0: Incoming call id = 0x002B, dsl 0
4d16h: ISDN BR0: LIF_EVENT: ces/callid 1/0x2B HOST_INCOMING_CALL
4d16h: ISDN BR0: HOST_INCOMING_CALL: (non-POTS) DATA
4d16h: ISDN BR0: HOST_INCOMING_CALL: (1) call_type = DATA
4d16h: ISDN BR0: HOST_INCOMING_CALL: voice_answer_data = FALSE call type is DATA
4d16h: ISDN BR0: Event: Received a DATA call from <unknown> on B2 at 64 Kb/s
4d16h: ISDN BR0: Event: Accepting the call id 0x2B
4d16h: BR0:2 PPP: Phase is DOWN, Setup [0 sess, 1 load]
4d16h: BR0:2 PPP: Phase is ESTABLISHING [0 sess, 1 load]
4d16h: BR0:2: inteSarface must be fifo queue, force fifo
4d16h: %DIALER-6-BIND: Interface BR0:2 bound to profile Di1
4d16h: ISDN BR0: RM returned call_type 0 resource type 0 response 1
4d16h: CCBRI_Go Fr Host InPkgInfo (Len=9) :
4d16h: 7 0 1 0 2B 3 18 1 8A
4d16h:
4d16h: ISDN BR0: isdn_send_connect(): msg 4, call id 0x2B, ces 1 bchan 1, c
all type DATA
4d16h: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
4d16h: ISDN: get_isdn_service_state(): idb 0x1A2EAC bchan 3 is_isdn 1 Not a Pri
4d16h: BR0:2 PPP: Treating connection as a callin
4d16h: BR0:2 LCP: State is Listen
4d16h: CCBRI_Go Fr Host InPkgInfo (Len=6) :
4d16h: 4 0 1 0 2B 0
4d16h:
4d16h: ISDN BR0: TX -> INFOc sapi=0 tei=105 ns=7 nr=5 i=0x0801C10218018A
4d16h:     CALL_PROC pd = 8  callref = 0xC1
4d16h:         Channel ID i = 0x8A
4d16h: ISDN BR0: RX <- RRr sapi=0 tei=105 nr=8
4d16h: ISDN BR0: TX -> INFOc sapi=0 tei=105 ns=8 nr=5 i=0x0801C107
4d16h:     CONNECT pd = 8  callref = 0xC1
4d16h: ISDN BR0: RX <- INFOc sapi=0 tei=105 ns=5 nr=9 i=0x0801410F
4d16h:     CONNECT_ACK pd = 8  callref = 0x41
4d16h: ISDN BR0: TX -> RRr sapi=0 tei=105 nr=6
4d16h: CCBRI_Go Fr L3 pkt (Len=4) :
4d16h: F 1 C1 92
4d16h:
4d16h: ISDN BR0: LIF_EVENT: ces/callid 1/0x2B HOST_CONNECT
4d16h: ISDN BR0: Event: Connected to <unknown> on B2 at 64 Kb/s
4d16h: BR0:2 LCP: I CONFREQ [Listen] id 1 len 10
4d16h: BR0:2 LCP:    MagicNumber 0x6515B12A (0x05066515B12A)
4d16h: BR0:2 LCP: O CONFREQ [Listen] id 1 len 15
4d16h: BR0:2 LCP:    AuthProto CHAP (0x0305C22305)
4d16h: BR0:2 LCP:    MagicNumber 0x788C6F8F (0x0506788C6F8F)
4d16h: BR0:2 LCP: O CONFACK [Listen] id 1 len 10
4d16h: BR0:2 LCP:    MagicNumber 0x6515B12A (0x05066515B12A)
4d16h: BR0:2 LCP: I CONFACK [ACKsent] id 1 len 15
4d16h: BR0:2 LCP:    AuthProto CHAP (0x0305C22305)
4d16h: BR0:2 LCP:    MagicNumber 0x788C6F8F (0x0506788C6F8F)
4d16h: BR0:2 LCP: State is Open
4d16h: BR0:2 PPP: Phase is AUTHENTICATING, by this end [0 sess, 0 load]
4d16h: BR0:2 CHAP: O CHALLENGE id 31 len 27 from "Saturn"
4d16h: BR0:2 CHAP: I RESPONSE id 31 len 26 from "Venus"
4d16h: BR0:2 CHAP: O SUCCESS id 31 len 4
4d16h: BR0:2 PPP: Phase is UP [0 sess, 0 load]
4d16h: BR0:2 BNCP: O CONFREQ [Closed] id 1 len 4
4d16h: BR0:2 CDPCP: O CONFREQ [Closed] id 1 len 4
4d16h: BR0:2 BNCP: I CONFREQ [REQsent] id 1 len 4
4d16h: BR0:2 BNCP: O CONFACK [REQsent] id 1 len 4: BR0:2 IPCP: I CONFREQ 
[Not negotiated] id 1 len 10
4d16h: BR0:2 IPCP:    Address 10.1.1.2 (0x03060A010102)
4d16h: BR0:2 LCP: O PROTREJ [Open] id 2 len 16 protocol IPCP 
(0x80210101000A03060A010102)
4d16h: BR0:2 CDPCP: I
4d16h CONFREQ [REQsent] id 1 len 4
4d16h: BR0:2 CDPCP: O CONFACK [REQsent] id 1 len 4
4d16h: BR0:2 BNCP: I CONFACK [ACKsent] id 1 len 4
4d16h: BR0:2 BNCP: State is Open
4d16h: BR0:2 CDPCP: I CONFACK [ACKsent] id 1 len 4
4d16h: BR0:2 CDPCP: State is Open
4d16h: BR0:2 DDR: dialer protocol up
4d16h: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, changed state to up
4d16h: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 
<unknown phone number> Venus   

!--- Unknown phone number because of no dialer string on Saturn

Saturn#

Discussões relacionadas da comunidade de suporte da Cisco

A Comunidade de Suporte da Cisco é um fórum onde você pode perguntar e responder, oferecer sugestões e colaborar com colegas.


Informações Relacionadas


Document ID: 10381