Discar e acessar : Conexões assíncronas

Configuração de uma Interface T1 ou E1 para Chamadas Analógicas de Saída Usando o Comando modem dialout controller

19 Setembro 2015 - Tradução por Computador
Outras Versões: Versão em PDFpdf | Inglês (22 Agosto 2015) | Feedback


Índice


Introdução

Esta configuração de exemplo ilustra como configurar uma interface T1 ou E1 para chamadas analógicas de saída com o comando modem dialout controller

Antes de Começar

Convenções

Para obter mais informações sobre convenções de documento, consulte as Convenções de dicas técnicas Cisco.

Pré-requisitos

Não existem requisitos específicos para este documento.

Componentes Utilizados

As informações neste documento são baseadas nas versões de software e hardware abaixo.

  • Software Release 12.1(5)T de Cisco IOS�

  • Cisco AS5300 com duas PRIs E1

Nota: O comando modem dialout controller foi introduzido no software Cisco IOS Release 12.1(T). Recomendamos o software Cisco IOS Release 12.1(3)T ou mais novo para esta implementação. O comando modem dialout controller dá suporte a várias interfaces, a partir do software IOS Release 12.1(5)T. Por exemplo:

AS5300-3(config)#line 1 60
AS5300-3(config-line)#modem dialout controller t1 ?
	 <0-7>  List of controllers to dial out

AS5300-3(config-line)#modem dialout controller t1 0,1,3

As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. Todos os dispositivos utilizados neste documento foram iniciados com uma configuração (padrão) inicial. Se você estiver trabalhando em uma rede ativa, certifique-se de que entende o impacto potencial de qualquer comando antes de utilizá-lo.

Visão geral

Para que as chamadas analógicas de saída usem determinada linha T1/E1, use o comando modem dialout controller. Esse comando é configurado no modo de configuração de linha; assim, os modems ficam limitados à interface T1/E1 especificada para qualquer chamada analógica de saída. Você poderá então configurar os comandos necessários de roteamento de discagem por demanda (DDR, dial on demand routing) na interface assíncrona (ou group-async) correspondente aos modems.

Nesta configuração de exemplo, um servidor de acesso à rede (NAS, network access server) Cisco AS5300 tem duas Interfaces de acesso básico (PRIs, Primary Rate Interfaces), cada uma mapeada para um Serviço de identificação de número discado (DNIS, Dialed Number Identification Service) diferente. Se um cliente disca 8210, a telco comuta a chamada para E1 0, e uma chamada para 8211 é comutada para E1 1. Essa configuração também usa pooling de modem para alocar modems com base nas mensagens do número chamado (DNIS) entregues pelo switch telco durante a configuração de chamada. Dessa forma, as chamadas para determinado número serão "respondidas" apenas por um modem que seja membro de um conjunto de modems específico. Como cada T1/E1 também está limitada a determinado número chamado, correlacionamos efetivamente um conjunto de modems a uma T1/E1 específica para chamadas recebidas.

Para demonstrar o cenário de discagem, o cliente solicita um retorno do servidor de acesso. O retorno é configurado localmente no servidor de acesso, mas os atributos do retorno também podem ser obtidos de um servidor de autenticação, autorização e auditoria (AAA, authentication, authorization, and accounting) RADIUS/TACACS+. Para uma chamada recebida em um número específico, a chamada é comutada para a T1 apropriada e respondida por um membro do conjunto de modems. Depois que o retorno é negociado, o servidor de acesso desconecta a chamada e um retorno é iniciado no mesmo modem. A discagem então é feita usando a interface T1 ou E1 especificada no comando modem dialout controller. Neste exemplo, a discagem é configurada para estar na mesma T1/E1 que a chamada recebida.

Configurar

Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.

Nota: Para encontrar a informação adicional nos comandos usados neste documento, use a ferramenta de pesquisa do comando IOS (clientes registrados somente).

Diagrama de Rede

Este documento utiliza a instalação de rede mostrada no diagrama abaixo.

/image/gif/paws/9499/modemdialoutcontroller.gif

Configurações

Este documento utiliza as configurações mostradas abaixo.

Configuração do Servidor de Acesso
Current configuration:

!
version 12.1
service timestamps debug datetime msec
service timestamps log uptime msec
no service password-encryption
!
hostname lala
!
logging rate-limit console 10 except errors
!
username testuser callback-dialstring 6036 password 0 test

!-- Access server calls back testuser at phone number 6036
!-- The callback parameters can also be configured on a RADIUS/TACACS+ server.

!
spe 1/0 1/9
firmware location system:/ucode/mica_port_firmware
spe 2/0 2/23
firmware location system:/ucode/microcom_firmware
!
resource-pool disable
!
modem-pool ModemPool8210

!-- Modem pool for calls to a specific phone number

pool-range 1-40

!-- The range of the modems in the pool
!-- Modems 1 through 40 are included in this pool

called-number 8210 max-conn 40

!-- Specifies the DNIS to be used for this modem pool
!-- Incoming calls for phone number 8210 are assigned to this
 pool
!
modem-pool ModemPool8211
pool-range 41-60,61-84

!-- The range of the modems in the pool
!-- Modems 41 through 84 are included in this pool

called-number 8211 max-conn 44

!-- Incoming calls for phone number 8211 are assigned to this pool

!
ip subnet-zero
no ip finger
!
isdn switch-type primary-net5
chat-script mod ABORT ERROR ABORT BUSY "" "AT" OK "ATDT \T" TIMEOUT 30 CONNECT \c

!-- Chat script for dialout

!
controller E1 0

!-- DNIS number for this E1 is 8210

clock source line primary
pri-group timeslots 1-31
!
controller E1 1

!-- DNIS number for this E1 is 8211

clock source line secondary 1
pri-group timeslots 1-31
!
controller E1 2
!
controller E1 3
!
!
interface Ethernet0
ip address 10.200.20.22 255.255.255.0
!
interface Serial0:15

!-- D-channel for E1 0
!-- DNIS number for this PRI is 8210

description PRI 8210
no ip address
encapsulation ppp
isdn switch-type primary-net5
isdn incoming-voice modem

!-- All incoming voice calls on this E1 are sent to the modems

!
interface Serial1:15

!-- D-channel for E1 1
!-- DNIS number for this PRI is 8211

description PRI 8211
no ip address
encapsulation ppp
isdn switch-type primary-net5
isdn incoming-voice modem

!-- All incoming voice calls on this E1 are sent to the modems

!
interface Group-Async1
ip unnumbered Ethernet0
encapsulation ppp
async mode interactive
peer default ip address pool dialup

!-- Assign IP address for incoming calls (with DNIS 8210) from pool dialup

ppp callback accept

!-- Permit PPP Callback

ppp authentication chap
group-range 1 40

!-- Interface includes modems 1 through 40 that are also in ModemPool8210

!
interface Group-Async2
ip unnumbered Ethernet0
encapsulation ppp
async mode interactive
peer default ip address pool dialup2

!-- Assign IP address for incoming calls (with DNIS 8211) from pool dialup2

ppp callback accept

!-- Here we accept the callback

ppp authentication chap
group-range 41 84

!-- Interface includes modems 41 through 84 that are also in ModemPool8211

!
ip local pool dialup 192.168.100.1 192.168.100.15
ip local pool dialup2 192.168.200.32 192.168.200.126

!-- Define the IP address ranges for the 2 pools

ip classless
no ip http server
!
line con 0
exec-timeout 0 0
transport input none
line 1 40

!-- Line configuration for modems 1-40
!-- These modems are in pool ModemPool8210

autoselect during-login
autoselect ppp
script callback mod

!-- Invoke chat script mod for the callback

login local
modem InOut

!-- Set the modems for dialin and dialout

modem dialout controller e1 0

!-- Outgoing call on these modems use e1 0

line 41 84

!-- Line configuration for modems 41-84
!-- These modems are in pool ModemPool8210

autoselect during-login
autoselect ppp
script callback mod

!-- Invoke chat script mod for the callback

login local
modem InOut
modem dialout controller e1 1

!-- Outgoing call on these modems use e1 1

line aux 0
line vty 0 4
!
end

Verificar

No momento, não há procedimento de verificação disponível para esta configuração.

Troubleshooting

Esta seção fornece informações que podem ser usadas para o troubleshooting da sua configuração.

Comandos para Troubleshooting

Os determinados comandos de exibição são apoiados pela ferramenta Output Interpreter (clientes registrados somente), que permite que você ver uma análise do emissor de comando de execução.

Nota: Antes de emitir comandos debug, consulte Informações importantes sobre comandos debug.

  • debug isdn q931 - Mostra as configurações de chamada e o desligamento da conexão de rede ISDN (camada 3) entre o roteador e o Switch ISDN.

  • debug ppp negotiation - Mostra informações sobre trocas e sobre o tráfego Point-to-Point Protocol (PPP) durante a negociação dos componentes PPP, incluindo o Link Control Protocol (LCP), a autenticação e o Network Control Protocol (NCP). Uma negociação PPP bem-sucedida abre primeiramente o estado LCP; em seguida, efetua a autenticação e, finalmente, negocia o NCP (geralmente o IP Control Protocol - IPCP).

  • debug ppp authentication – Exibe mensagens de protocolo de autenticação PPP, incluindo intercâmbios de pacote de Protocolo de Autenticação de Desafio (CHAP) e intercâmbios de Protocolo de Autenticação de Senha (PAP).

  • debug chat - Para monitorar a execução do script de bate-papo quando a discagem do serviço telefônico comum (POTS, plain old telephone service)/assíncrono é iniciada. Um script de bate-papo é um conjunto de pares de strings expect-send que definem o reconhecimento entre os dispositivos do equipamento de terminal de dados (DTE, data terminal equipment) e do equipamento de comunicação de dados (DCE, data communications equipment).

  • debug callback - Mostra eventos de retorno quando o roteador está usando um modem e um script de bate-papo a ser retornado por uma linha do terminal.

  • debug dialer - Mostra informações de debugação dos pacotes recebidos na interface do discador.

  • debug modem csm (não mostrado aqui) - Mostra informações de debugação na máquina de estado de chamada usada para conectar chamadas no modem. Mostra como a chamada do modem é tratada pelo processo de gerenciamento do modem interno.

Exemplo de debug

Abaixo está a saída obtida com os comandos debug mostrados acima.

A saída mostra o cliente efetuando uma chamada para 8210. A chamada é comutada para E1 0 e atendida pelo modem 14 (Async 14), que é membro do conjunto ModemPool8210. A chamada estabelece a conexão, o PPP (e o retorno) é negociado, o cliente é autenticado e o AS5300 desconecta a chamada preparando o retorno. O roteador inicia então o retorno usando o mesmo modem (Async 14). Com o comando modem dialout controller, a chamada usa E1 0 e a discagem é efetuada.

Nota: Algumas das linhas mais longas de debugação foram quebradas para impressão adequada. As linhas que começam sem carimbo de hora/data são do final da linha anterior.

*Jan  1 05:00:43.018: ISDN Se0:15: RX <-  SETUP pd = 8  callref = 0x266A
!-- Incoming Call on E1 0
*Jan  1 05:00:43.018:         Sending Complete
*Jan  1 05:00:43.018:         Bearer Capability i = 0x9090A3
*Jan  1 05:00:43.018:         Channel ID i = 0xA18398
*Jan  1 05:00:43.022:         Progress Ind i = 0x8183 
- Origination address is non-ISDN
*Jan  1 05:00:43.022:         Calling Party Number i = 0xA1, '6036',Plan:ISDN, 
Type:National
*Jan  1 05:00:43.022:         Called Party Number i = 0x81, '210', Plan:ISDN, 
Type:Unknown

!-- The called number (DNIS) for the incoming call is (8)210

*Jan  1 05:00:43.022:         Locking Shift to Codeset 6
*Jan  1 05:00:43.022:         Codeset 6 IE 0x28  i = 'Analog', 0x20, '36'
*Jan  1 05:00:43.026: ISDN Se0:15: TX ->  CALL_PROC pd = 8  callref =0xA66A
*Jan  1 05:00:43.026:         Channel ID i = 0xA98398
*Jan  1 05:00:43.030: ISDN Se0:15: TX ->  ALERTING pd = 8  callref = 0xA66A
*Jan  1 05:00:43.082: ISDN Se0:15: TX ->  CONNECT pd = 8  callref = 0xA66A
*Jan  1 05:00:43.146: ISDN Se0:15: RX <-  CONNECT_ACK pd = 8  callref =0x266A
*Jan  1 05:00:43.146: ISDN Se0:15: CALL_PROGRESS: CALL_CONNECTED call id0x63, 
bchan 23, dsl 0
*Jan  1 05:00:45: %ISDN-6-CONNECT: Interface Serial0:23 is now 
connected to 6036

!-- Call is connected

*Jan  1 05:01:11.158: As14 LCP: I CONFREQ [Closed] id 1 len 50

!-- PPP negotiation begins. Note that the call is on 
!-- Async 14, which is a member of the pool ModemPool8210

*Jan  1 05:01:11.158: As14 LCP:    ACCM 0x00000000 (0x020600000000)
*Jan  1 05:01:11.158: As14 LCP:    MagicNumber 0x75D617D5 (0x050675D617D5)
*Jan  1 05:01:11.158: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:11.158: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:11.158: As14 LCP:    Callback 6  (0x0D0306)
*Jan  1 05:01:11.158: As14 LCP:    MRRU 1614 (0x1104064E)
*Jan  1 05:01:11.158: As14 LCP:    EndpointDisc 1 Local
*Jan  1 05:01:11.158: As14 LCP:     (0x13170177DE54DA55A24ADD8043063898)
*Jan  1 05:01:11.158: As14 LCP:     (0x1C049700000000)
*Jan  1 05:01:11.158: As14 LCP: Lower layer not up, Fast Starting
*Jan  1 05:01:11.158: As14 PPP: Treating connection as a dedicated line
*Jan  1 05:01:11.158: As14 PPP: Phase is ESTABLISHING, Active Open 
[0 sess,1 load]
*Jan  1 05:01:11.158: As14 LCP: O CONFREQ [Closed] id 1 len 25
*Jan  1 05:01:11.158: As14 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Jan  1 05:01:11.158: As14 LCP:    AuthProto CHAP (0x0305C22305)
*Jan  1 05:01:11.158: As14 LCP:    MagicNumber 0x118F14E6 (0x0506118F14E6)
*Jan  1 05:01:11.158: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:11.158: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:11.158: As14 LCP: O CONFREJ [REQsent] id 1 len 31
*Jan  1 05:01:11.158: As14 LCP:    MRRU 1614 (0x1104064E)
*Jan  1 05:01:11.158: As14 LCP:    EndpointDisc 1 Local
*Jan  1 05:01:11.158: As14 LCP:     (0x13170177DE54DA55A24ADD8043063898)
*Jan  1 05:01:11.162: As14 LCP:     (0x1C049700000000)
*Jan  1 05:01:13: %LINK-3-UPDOWN: Interface Async14, changed state to up

!-- Interface Async 14 is up

*Jan  1 05:01:11.302: As14 LCP: I CONFACK [REQsent] id 1 len 25
*Jan  1 05:01:11.302: As14 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Jan  1 05:01:11.302: As14 LCP:    AuthProto CHAP (0x0305C22305)
*Jan  1 05:01:11.302: As14 LCP:    MagicNumber 0x118F14E6 (0x0506118F14E6)
*Jan  1 05:01:11.302: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:11.302: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:11.302: As14 LCP: I CONFREQ [ACKrcvd] id 2 len 23
*Jan  1 05:01:11.302: As14 LCP:    ACCM 0x00000000 (0x020600000000)
*Jan  1 05:01:11.302: As14 LCP:    MagicNumber 0x75D617D5 (0x050675D617D5)
*Jan  1 05:01:11.302: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:11.302: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:11.302: As14 LCP:    Callback 6  (0x0D0306)
*Jan  1 05:01:11.302: As14 LCP: O CONFACK [ACKrcvd] id 2 len 23
*Jan  1 05:01:11.302: As14 LCP:    ACCM 0x00000000 (0x020600000000)
*Jan  1 05:01:11.302: As14 LCP:    MagicNumber 0x75D617D5 (0x050675D617D5)
*Jan  1 05:01:11.302: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:11.302: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:11.302: As14 LCP:    Callback 6  (0x0D0306)

!-- Callback is negotiated

*Jan  1 05:01:11.302: As14 LCP: State is Open
*Jan  1 05:01:11.302: As14 PPP: Phase is AUTHENTICATING, by this end 
[0 sess, 1 load]
*Jan  1 05:01:11.302: As14 CHAP: O CHALLENGE id 1 len 25 from "lala"
*Jan  1 05:01:11.446: As14 LCP: I IDENTIFY [Open] id 3 len 18 magic 
0x75D617D5 MSRASV5.00
*Jan  1 05:01:11.462: As14 LCP: I IDENTIFY [Open] id 4 len 28 magic 
0x75D617D5 MSRAS-1-TESTPC-W2K
*Jan  1 05:01:11.462: As14 CHAP: I RESPONSE id 1 len 29 from "testuser"
*Jan  1 05:01:11.462: As14 CHAP: O SUCCESS id 1 len 4

!-- CHAP authentication is successful

*Jan  1 05:01:11.462: As14 MCB: User testuser  Callback Number - Server 6036

!-- Number to be used for callback, configured locally in the username 
!-- command. The callback information can be off loaded to an AAA server.

*Jan  1 05:01:11.462: Async14 PPP: O MCB Request(1) id 1 len 7
*Jan  1 05:01:11.462: Async14 MCB: O  1  1  0  7  3  3  0
*Jan  1 05:01:11.462: As14 MCB: O Request Id 1 Callback Type 
Server-Num delay 0
*Jan  1 05:01:11.462: As14 PPP: Phase is CBCP [0 sess, 1 load]
*Jan  1 05:01:11.606: Async14 PPP: I MCB Response(2) id 1 len 7
*Jan  1 05:01:11.606: Async14 MCB: I  2  1  0  7  3  3  C
*Jan  1 05:01:11.606: As14 MCB: Received response
*Jan  1 05:01:11.606: As14 MCB: Response CBK-Server-Num 3 3 12
*Jan  1 05:01:11.606: Async14 PPP: O MCB Ack(3) id 2 len 7
*Jan  1 05:01:11.606: Async14 MCB: O  3  2  0  7  3  3  C
*Jan  1 05:01:11.606: As14 MCB: O Ack Id 2 Callback Type Server-Num delay 12
*Jan  1 05:01:11.606: As14 MCB: Negotiated MCB with peer
*Jan  1 05:01:11.734: As14 LCP: I TERMREQ [Open] id 5 len 16 
(0x75D617D5003CCD7400000000)
*Jan  1 05:01:11.734: As14 LCP: O TERMACK [Open] id 5 len 4
*Jan  1 05:01:11.734: As14 MCB: Peer terminating the link
*Jan  1 05:01:11.734: As14 MCB: Link terminated by peer, Callback Needed
*Jan  1 05:01:11.734: As14 MCB: Initiate Callback for testuser at 6036 
using Async
*Jan  1 05:01:11.734: As14 MCB: Async-callback in progress
*Jan  1 05:01:11.734: As14 PPP: Phase is TERMINATING [0 sess, 1 load]
*Jan  1 05:01:11.734: TTY14 Callback PPP process creation
*Jan  1 05:01:11.734: TTY14: Callback script exists 
- no script creation necessary
*Jan  1 05:01:11.734: TTY14 Callback process initiated, user: 
testuser dialstring 6036
*Jan  1 05:01:14: %ISDN-6-DISCONNECT: Interface Serial0:23  disconnected 
from 6036, call lasted 29 seconds

!-- Call is disconnected

*Jan  1 05:01:12.386: ISDN Se0:15: TX ->  DISCONNECT pd = 8  
callref = 0xA66A
*Jan  1 05:01:12.386:         Cause i = 0x809F - Normal, unspecified
*Jan  1 05:01:12.450: ISDN Se0:15: RX <-  RELEASE pd = 8  callref = 0x266A
*Jan  1 05:01:12.450: ISDN Se0:15: TX ->  RELEASE_COMP pd = 8  
callref = 0xA66A
*Jan  1 05:01:13.734: As14 LCP: TIMEout: State TERMsent
*Jan  1 05:01:13.734: As14 LCP: State is Closed
*Jan  1 05:01:13.734: As14 PPP: Phase is DOWN [0 sess, 1 load]
*Jan  1 05:01:13.734: As14 PPP: Phase is ESTABLISHING, Passive Open 
[0 sess, 1 load]
*Jan  1 05:01:13.734: As14 LCP: State is Listen
*Jan  1 05:01:16: %LINK-5-CHANGED: Interface Async14, changed state to reset
*Jan  1 05:01:14.734: As14 LCP: State is Closed
*Jan  1 05:01:14.734: As14 PPP: Phase is DOWN [0 sess, 1 load]
*Jan  1 05:01:17.734: As14 IPCP: Remove route to 192.168.100.13
*Jan  1 05:01:17.734: TTY14 Callback forced wait = 4 seconds
*Jan  1 05:01:21: %LINK-3-UPDOWN: Interface Async14, changed state to down
*Jan  1 05:01:19.734: As14 LCP: State is Closed
*Jan  1 05:01:21.766: CHAT14: Matched chat script mod to string mod
*Jan  1 05:01:21.766: CHAT14: Asserting DTR
*Jan  1 05:01:21.766: CHAT14: Chat script mod started

!-- Callback chatscript mod is started

*Jan  1 05:01:21.766: CHAT14: Sending string: ATZ
*Jan  1 05:01:21.766: CHAT14: Expecting string: OK
*Jan  1 05:01:21.814: CHAT14: Completed match for expect: OK
*Jan  1 05:01:21.814: CHAT14: Sending string: ATDT \T<6036>

!-- Dial 6036 per the callback configuration

*Jan  1 05:01:21.814: CHAT14: Expecting string: CONNECT
*Jan  1 05:01:21.902: ISDN Se0:15: TX ->  SETUP pd = 8  callref = 0x0008

!-- The outgoing call uses E1 0 as per the modem dialout controller 
!-- command for modem 14.

*Jan  1 05:01:21.902:         Bearer Capability i = 0x8090A3
*Jan  1 05:01:21.902:         Channel ID i = 0xA9839F
*Jan  1 05:01:21.902:         Progress Ind i = 0x8183 
- Origination address is non-ISDN
*Jan  1 05:01:21.902:         Calling Party Number i = 0x80, '6036',
Plan:Unknown, Type:Unknown
*Jan  1 05:01:21.902:         Called Party Number i = 0x80, '6036',
Plan:Unknown, Type:Unknown
*Jan  1 05:01:21.946: ISDN Se0:15: RX <-  CALL_PROC pd = 8  
callref = 0x8008
*Jan  1 05:01:21.946:         Channel ID i = 0xA9839F
*Jan  1 05:01:21.974: ISDN Se0:15: RX <-  ALERTING pd = 8  callref = 0x8008
*Jan  1 05:01:28.958: ISDN Se0:15: RX <-  CONNECT pd = 8  callref = 0x8008
*Jan  1 05:01:28.962:         Progress Ind i = 0x8182 
- Destination address is non-ISDN
*Jan  1 05:01:28.962:         Connected Number i = 0xA136303336
*Jan  1 05:01:28.962:         Locking Shift to Codeset 6
*Jan  1 05:01:28.962:         Codeset 6 IE 0x28  i = 'Analog', 0x20, '36'
*Jan  1 05:01:31: %ISDN-6-CONNECT: 
Interface Serial0:30 is now connected to 6036
*Jan  1 05:01:28.966: ISDN Se0:15: TX ->  CONNECT_ACK pd = 8  
callref =0x0008
*Jan  1 05:01:41.562: CHAT14: Completed match for expect: CONNECT
*Jan  1 05:01:41.566: CHAT14: Sending string: \c
*Jan  1 05:01:41.566: CHAT14: Chat script mod finished, status = Success
*Jan  1 05:01:41.598: TTY14: Callback starting PPP directly with 
Invalid auth info
*Jan  1 05:01:41.642: As14 LCP: I CONFREQ [Closed] id 0 len 47

!-- PPP negotiation begins

*Jan  1 05:01:41.646: As14 LCP:    ACCM 0x00000000 (0x020600000000)
*Jan  1 05:01:41.646: As14 LCP:    MagicNumber 0x143F35CB (0x0506143F35CB)
*Jan  1 05:01:41.646: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:41.646: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:41.646: As14 LCP:    MRRU 1614 (0x1104064E)
*Jan  1 05:01:41.646: As14 LCP:    EndpointDisc 1 Local
*Jan  1 05:01:41.646: As14 LCP:     (0x13170177DE54DA55A24ADD8043063898)
*Jan  1 05:01:41.646: As14 LCP:     (0x1C049700000000)
*Jan  1 05:01:41.646: As14 LCP: Lower layer not up, Fast Starting
*Jan  1 05:01:41.646: As14 PPP: Treating connection as a callout
*Jan  1 05:01:41.646: As14 PPP: Phase is ESTABLISHING, Active Open 
[0 sess,1 load]
*Jan  1 05:01:41.646: As14 LCP: O CONFREQ [Closed] id 2 len 25
*Jan  1 05:01:41.646: As14 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Jan  1 05:01:41.646: As14 LCP:    AuthProto CHAP (0x0305C22305)
*Jan  1 05:01:41.646: As14 LCP:    MagicNumber 0x118F8C01 (0x0506118F8C01)
*Jan  1 05:01:41.646: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:41.646: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:41.646: As14 LCP: O CONFREJ [REQsent] id 0 len 31
*Jan  1 05:01:41.646: As14 LCP:    MRRU 1614 (0x1104064E)
*Jan  1 05:01:41.646: As14 LCP:    EndpointDisc 1 Local
*Jan  1 05:01:41.646: As14 LCP:     (0x13170177DE54DA55A24ADD8043063898)
*Jan  1 05:01:41.646: As14 LCP:     (0x1C049700000000)
*Jan  1 05:01:43: %LINK-3-UPDOWN: Interface Async14, changed state to up
*Jan  1 05:01:41.810: As14 LCP: I CONFACK [REQsent] id 2 len 25
*Jan  1 05:01:41.810: As14 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Jan  1 05:01:41.810: As14 LCP:    AuthProto CHAP (0x0305C22305)
*Jan  1 05:01:41.810: As14 LCP:    MagicNumber 0x118F8C01 (0x0506118F8C01)
*Jan  1 05:01:41.810: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:41.810: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:41.842: As14 LCP: I CONFREQ [ACKrcvd] id 1 len 20
*Jan  1 05:01:41.842: As14 LCP:    ACCM 0x00000000 (0x020600000000)
*Jan  1 05:01:41.842: As14 LCP:    MagicNumber 0x143F35CB (0x0506143F35CB)
*Jan  1 05:01:41.842: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:41.842: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:41.842: As14 LCP: O CONFACK [ACKrcvd] id 1 len 20
*Jan  1 05:01:41.842: As14 LCP:    ACCM 0x00000000 (0x020600000000)
*Jan  1 05:01:41.842: As14 LCP:    MagicNumber 0x143F35CB (0x0506143F35CB)
*Jan  1 05:01:41.842: As14 LCP:    PFC (0x0702)
*Jan  1 05:01:41.842: As14 LCP:    ACFC (0x0802)
*Jan  1 05:01:41.842: As14 LCP: State is Open
*Jan  1 05:01:41.842: As14 PPP: Phase is AUTHENTICATING, by this end 
[0 sess, 1 load]
*Jan  1 05:01:41.842: As14 CHAP: O CHALLENGE id 2 len 25 from "lala"
*Jan  1 05:01:42.002: As14 LCP: I IDENTIFY [Open] id 2 len 18 magic 
0x143F35CB MSRASV5.00
*Jan  1 05:01:42.018: As14 LCP: I IDENTIFY [Open] id 3 len 28 magic 
0x143F35CB MSRAS-1-TESTPC-W2K
*Jan  1 05:01:42.034: As14 CHAP: I RESPONSE id 2 len 29 from "testuser"
*Jan  1 05:01:42.034: As14 CHAP: O SUCCESS id 2 len 4

!-- PPP negotiation is successful

*Jan  1 05:01:42.034: As14 PPP: Phase is UP [0 sess, 1 load]
*Jan  1 05:01:42.034: As14 IPCP: O CONFREQ [Closed] id 1 len 10

!-- IPCP parameters are now negotiated

*Jan  1 05:01:42.034: As14 IPCP:    Address 10.200.20.22 (0x03060AC81416)
*Jan  1 05:01:42.194: As14 CCP: I CONFREQ [Not negotiated] id 4 len 10
*Jan  1 05:01:42.194: As14 CCP:    MS-PPC supported bits 0x00000001 
(0x120600000001)
*Jan  1 05:01:42.194: As14 LCP: O PROTREJ [Open] id 3 len 16 protocol CCP 
(0x80FD0104000A120600000001)
*Jan  1 05:01:42.210: As14 IPCP: I CONFREQ [REQsent] id 5 len 40
*Jan  1 05:01:42.210: As14 IPCP:    CompressType VJ 15 slots CompressSlotID
(0x0206002D0F01)
*Jan  1 05:01:42.210: As14 IPCP:    Address 0.0.0.0 (0x030600000000)
*Jan  1 05:01:42.210: As14 IPCP:    PrimaryDNS 0.0.0.0 (0x810600000000)
*Jan  1 05:01:42.210: As14 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
*Jan  1 05:01:42.210: As14 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
*Jan  1 05:01:42.210: As14 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
*Jan  1 05:01:42.210: As14 IPCP: O CONFREJ [REQsent] id 5 len 34
*Jan  1 05:01:42.210: As14 IPCP:    CompressType VJ 15 slots CompressSlotID
(0x0206002D0F01)
*Jan  1 05:01:42.210: As14 IPCP:    PrimaryDNS 0.0.0.0 (0x810600000000)
*Jan  1 05:01:42.210: As14 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
*Jan  1 05:01:42.210: As14 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
*Jan  1 05:01:42.210: As14 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
*Jan  1 05:01:42.214: As14 IPCP: I CONFACK [REQsent] id 1 len 10
*Jan  1 05:01:42.214: As14 IPCP:    Address 10.200.20.22 (0x03060AC81416)
*Jan  1 05:01:42.386: As14 IPCP: I CONFREQ [ACKrcvd] id 6 len 10
*Jan  1 05:01:42.386: As14 IPCP:    Address 0.0.0.0 (0x030600000000)
*Jan  1 05:01:42.386: As14 IPCP: O CONFNAK [ACKrcvd] id 6 len 10
*Jan  1 05:01:42.386: As14 IPCP:    Address 192.168.100.13 (0x0306C0A8640D)
*Jan  1 05:01:42.546: As14 IPCP: I CONFREQ [ACKrcvd] id 7 len 10
*Jan  1 05:01:42.546: As14 IPCP:    Address 192.168.100.13 (0x0306C0A8640D)
*Jan  1 05:01:42.546: As14 IPCP: O CONFACK [ACKrcvd] id 7 len 10
*Jan  1 05:01:42.546: As14 IPCP:    Address 192.168.100.13 (0x0306C0A8640D)
*Jan  1 05:01:42.546: As14 IPCP: State is Open
*Jan  1 05:01:42.550: As14 IPCP: Install route to 192.168.100.13
*Jan  1 05:01:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface Async14, 
changed state to up

!-- Callback connection is up, PPP negotiation is complete 
!-- and a route is installed.

Discussões relacionadas da comunidade de suporte da Cisco

A Comunidade de Suporte da Cisco é um fórum onde você pode perguntar e responder, oferecer sugestões e colaborar com colegas.


Informações Relacionadas


Document ID: 9499