排除Nexus 7000系列交换机上的硬件转发问题
下载选项
已更新: 2016 年 10 月 6 日
文档 ID:200300
非歧视性语言
此产品的文档集力求使用非歧视性语言。在本文档集中，非歧视性语言是指不隐含针对年龄、残障、性别、种族身份、族群身份、性取向、社会经济地位和交叉性的歧视的语言。由于产品软件的用户界面中使用的硬编码语言、基于 RFP 文档使用的语言或引用的第三方产品使用的语言，文档中可能无法确保完全使用非歧视性语言。 深入了解思科如何使用包容性语言。
关于此翻译
思科采用人工翻译与机器翻译相结合的方式将此文档翻译成不同语言，希望全球的用户都能通过各自的语言得到支持性的内容。 请注意：即使是最好的机器翻译，其准确度也不及专业翻译人员的水平。 Cisco Systems, Inc. 对于翻译的准确性不承担任何责任，并建议您总是参考英文原始文档（已提供链接）。
简介
本文档介绍如何对Cisco Nexus 7000系列交换机的F3系列模块上的硬件转发问题进行故障排除。
先决条件
要求
思科建议您先熟悉Cisco Nexus操作系统(NX-OS)和基本Nexus架构，然后再继续了解本文档中介绍的信息。
使用的组件
本文档中的信息基于以下软件和硬件版本：
- Cisco Nexus 7000系列交换机(N7K)
- 思科N7K F3系列模块（N7K-F312FQ-25,12端口10/40千兆以太网模块）
- Cisco NX-OS版本6.2.8a及更高版本
本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始（默认）配置。如果您的网络处于活动状态，请确保您了解所有命令的潜在影响。
背景信息
本文档主要介绍一些内置工具，当您已用尽转发表或控制平面的软件部分时，这些工具用于硬件故障排除。嵌入式逻辑分析器模块(ELAM)是一种专用集成电路(ASIC)，用于捕获单个数据包并显示转发后入口数据包在数据总线(DBUS)和结果总线(RBUS)上的显示方式。
ASIC嵌入到转发管道中，它可以实时捕获数据包，而不会中断性能或控制平面资源。这有助于回答以下问题：
- 数据包是否到达转发引擎(FE)?
- 数据包在哪个端口和VLAN上接收？
- 数据包如何显示(第2层(L2)或第4层(L4)数据)?
- 数据包如何更改，以及它在何处发送？
ELAM是功能强大、精细且非侵入性的工具，在硬件交换平台上工作的思科技术支持中心(TAC)工程师最常使用。但是，必须知道ELAM工具一次只捕获一个数据包。即，触发ELAM后收到的第一个数据包。
故障排除
本节介绍如何排除F3系列模块上的ELAM在不涉及使用分支电缆的部署以及使用分支电缆的部署中的故障。
排除F3系列模块上的ELAM故障，无分支电缆
以下是本节中用于示例的拓扑：
+-------------+ +-------------+ +------------+
| | | | | |
| | | | | |
| | e3/3-4 e3/1-2 | | e3/5 e3/7 | |
| N7K2 +-------------------+ N7K1 +---------------------+ N7K3 |
| +-------------------+ | .1 L3 .3 | |
| | Po1(Trunk) | | 192.168.13.0/24 | |
| | | | | |
+-------------+ +-------------+ +------------+
Vlan 10 SVI Vlan10 SVI
IP add 192.168.12.2/24 IP add 192.168.12.1/24
以下是有关此拓扑的一些说明：
- N7K运行NX-OS版本6.2.8a。
- 从N7K2 VLAN 10接口向远程IP地址192.168.12.1发送ping。
- ELAM捕获N7K1上的数据包。
- 使用N7K-F312FQ-25，该模块是插入插槽3的12端口10/40千兆以太网模块。
在对系统进行故障排除之前，您应确认基本连接：
N7K2# ping 192.168.13.3
PING 192.168.13.3 (192.168.13.3): 56 data bytes
64 bytes from 192.168.13.3: icmp_seq=0 ttl=253 time=1.513 ms
64 bytes from 192.168.13.3: icmp_seq=1 ttl=253 time=1.062 ms
64 bytes from 192.168.13.3: icmp_seq=2 ttl=253 time=0.822 ms
64 bytes from 192.168.13.3: icmp_seq=3 ttl=253 time=0.830 ms
64 bytes from 192.168.13.3: icmp_seq=4 ttl=253 time=0.845 ms
--- 192.168.13.3 ping statistics ---
5 packets transmitted, 5 packets received, 0.00% packet loss
round-trip min/avg/max = 0.822/1.014/1.513 ms
N7K2# show ip route 192.168.13.3
IP Route Table for VRF "default"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
'%<string>' in via output denotes VRF <string>
192.168.13.0/24, ubest/mbest: 1/0
*via 192.168.12.1, [1/0], 01:20:36, static
!--- The next command verifies the Address Resolution Protocol (ARP) for the next hop.
N7K2# show ip arp 192.168.12.1
----SNIP----
IP ARP Table
Total number of entries: 1
Address Age MAC Address Interface
192.168.12.1 00:10:29 e4c7.2210.a142 Vlan10
您还应验证Supervisor引擎(Sup)上的介质访问控制(MAC)地址学习和下一跳的模块：
N7K2# show mac address-table address e4c7.2210.a142
!--- This command output shows the MAC learning on the Sup (software).
Legend:
* - primary entry, G - Gateway MAC, (R) - Routed MAC, O - Overlay MAC
age - seconds since last seen,+ - primary entry using vPC Peer-Link,
(T) - True, (F) - False
VLAN MAC Address Type age Secure NTFY Ports/SWID.SSID.LID
---------+-----------------+--------+---------+------+----+------------------
* 10 e4c7.2210.a142 dynamic 120 F F Po1
此输出显示模块/硬件上的MAC学习；但是，为了了解接口，必须转换索引：
N7K2# show hardware mac address-table 3 address e4c7.2210.a142
FE | Valid| PI| BD | MAC | Index | Stat| SW | Modi| Age| Tmr| GM| Sec|
| | | | | | ic | | fied|Byte| Sel| | ure|
---|------|---|------|---------------|-------|-----|-----|-----|----|----|---|----|
1 1 1 41 e4c7.2210.a142 0x00a2a 0 0x089 1 185 1 0 0
| TR| NT| RM| RMA| Cap| Fld|Always| PV | RD| NN| UC|PI_E8| VIF | SWID| SSWID| LID |
| AP| FY| | |ture| | Learn| | | | | | | | | |
|---|---|---|----|----|----|------|----|---|---|---|-----|-----|-----|------|-------|
0 0 0 0 0 0 0 0x00 0 0 1 0 0x000 0x000 0x000 0x00a2a
N7K2# show system internal pixm info ltl 0x00a2a
!--- This is the index that was received in the previous output.
---SNIP---
PC_TYPE PORT LTL RES_ID LTL_FLAG CB_FLAG MEMB_CNT
------------------------------------------------------------------------------
Normal Po1 0x0a2a 0x16000000 0x00000000 0x00000002 2
Member rbh rbh_cnt
Eth3/4 0x000000f0 0x04
Eth3/3 0x0000000f 0x04
---SNIP---
输入以下命令以获取虚拟设备环境(VDC)编号(在本例中为3)，并直接检查模块上的MAC:
N7K2# show vdc
---SNIP---
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ---
3 N7K2 active e4:c7:22:10:a1:43 Ethernet f3
module-3#attach module 3
module-3# vdc 3
!--- This data is obtained from the previous command output.
module-3# show mac address-table address e4c7.2210.a142
Legend:
* - primary entry, G - Gateway MAC, (R) - Routed MAC, (d) - dec
Age - seconds since last seen,,+ - primary entry using vPC Peer-Link
(T) - True, (F) - False, h - hex, d - decimal
VDC = 3
FE VLAN/BD MAC Address Type Age Secure NTFY Ports/SWID.SSID.LID(d)
-----+------+-------------+--------+------+------+------+-----------------------
* 1 10 e4c7.2210.a142 dynamic 360 F F Po1
确定端口通道1上用于从N7K2转发Sup上流量的链路，以及当端口通道1从N7K1到N7K2使用时用于从N7K3发送应答的链路：
N7K2# show port-channel load-balance forwarding-path interface port-channel 1 src-ip
192.168.12.2 dst-ip 192.168.13.3 module 3
Module 3: Missing params will be substituted by 0's.
Load-balance Algorithm: src-dst ip
RBH: 0xd2 Outgoing port id: Ethernet3/3
N7K1# show port-channel load-balance forwarding-path interface port-channel 1 src-ip
192.168.13.3 dst-ip 192.168.12.2 module 3
Module 3: Missing params will be substituted by 0's.
Load-balance Algorithm: src-dst ip
RBH: 0xd2 Outgoing port id: Ethernet3/1
从N7K2（IP地址192.168.12.2）发送ping命令，并在N7K1上沿入口方向捕获数据包，以确认数据包被转发到N7K3（IP地址192.168.13.3）。
在发送ping之前，您应该了解硬件累积。完成以下步骤以了解累积：
- 附加模块：
N7K1# attach module 3
Attaching to module 3 ...
To exit type 'exit', to abort type '$.' - 确定侧翼实例。侧翼是F3系列模块的片上交换(SOC)ASIC。每个侧面模块映射到模块上的两个外部端口（信息会按模块类型更改，并特定于N7K-F312FQ-25）。
模块上有12个端口，每个ASIC映射到前面板上的两个端口，这意味着模块上有6(0-5)个侧面实例（实例计数为零）。注意：在开始之前，请确保您具有网络管理权限。
捕获通过N7K1上的端口通道1从N7K2到达的数据包时，请查找映射到每个实例的端口（e3/1和e3/2）：
module-3# show hardware internal dev-port-map
--------------------------------------------------------------
CARD_TYPE: 12 port 40G
>Front Panel ports:12
--------------------------------------------------------------
Device name Dev role Abbr num_inst:
--------------------------------------------------------------
> Flanker Eth Mac Driver DEV_ETHERNET_MAC MAC_0 6
> Flanker Fwd Driver DEV_LAYER_2_LOOKUP L2LKP 6
!--- Check for the L2LKP number for ports 1 and 2.
> Flanker Xbar Driver DEV_XBAR_INTF XBAR_INTF 6
> Flanker Queue Driver DEV_QUEUEING QUEUE 6
> Sacramento Xbar ASIC DEV_SWITCH_FABRIC SWICHF 1
> Flanker L3 Driver DEV_LAYER_3_LOOKUP L3LKP 6
> EDC DEV_PHY PHYS 2
+-----------------------------------------------------------------------+
+----------------+++FRONT PANEL PORT TO ASIC INSTANCE MAP+++------------+
+-----------------------------------------------------------------------+
FP port | PHYS | MAC_0 | L2LKP | L3LKP | QUEUE |SWICHF
1 0 0 0 0 0
!--- The L2KLP for both ports is 0, so both belong to instance 0.
2 0 0 0 0 0
3 1 1 1 1 0
4 1 1 1 1 0
5 0 2 2 2 2 0
6 0 2 2 2 2 0
7 1 3 3 3 3 0
8 1 3 3 3 3 0
9 4 4 4 4 0
10 4 4 4 4 0
11 5 5 5 5 0
12 5 5 5 5 0
+-----------------------------------------------------------------------+
+-----------------------------------------------------------------------+ - 选择实例，设置触发器，然后开始捕获。但是，必须了解ELAM触发器可以使用许多选项：
module-3# elam asic flanker instance 0
如果要将DBUS包括在捕获中（交换机接收的数据包），这两个选项非常重要。 这是未经查找的原始数据包。RBUS显示DBUS硬件中的查找结果。要获得完整的ELAM和分析，必须同时捕获RBUS和DBUS。
module-3(fln-elam)# layer2
module-3(fln-l2-elam)# trigger ?
dbus Pre L2 BUS
rbus Post L2 BUS
-----SNIP-----
下一个输出显示可使用DBUS选项捕获的数据包的类型。在本示例中，选择Internet协议版本4(IPv4)数据包：
module-3(fln-l2-elam)# trigger dbus ?
以下是一些可供您选择使用的其他选项：
arp ARP Frame Format
fc Fc hdr Frame Format
ipv4 IPV4 Frame Format
ipv6 IPV6 Frame Format
mpls MPLS
other L2 hdr Frame Format
pup PUP Frame Format
rarp RARP Frame Format
valid On valid packet
module-3(fln-l2-elam)# trigger dbus ipv4 ?
在本示例中，if句柄用于为捕获选择条件。下一个输出中显示的大多数选项都基于L2、L3和L4报头。源IP地址和目的IP地址也用于捕获。
egress Egress packets
!--- Capture packets in egress (outbound from the port).
if If Trigger Condition
ingress Ingress packets
!--- Capture packets in ingress (inbound to the port).
multicast Multicast packet
multicast-replication Multicast replication
module-3(fln-l2-elam)# trigger dbus ipv4 ingress if ?
此输出显示最终触发器选项：
<CR>
acos Acos
block-capture Capture l2 blocks
bpdu Bpdu
bundle-port Bundle-port
ccc Ccc
copp Copp
da-type Da-type
de-cfi De cfi
destination-index Destination-index
destination-ipv4-address destination ipv4 address
destination-mac-address Destination-mac-address
destination-vif Destination-vif
df df
dfst Dfst
dft Dft
disable-index-learn Disable-index-learn
disable-new-learn Disable-new-learn
dont-forward Dont-forward
dont-learn Dont-learn
dtag-ftag Dtag-ftag
dtag-ttl Dtag-ttl
dti-type-vpnid Dti type vpnid
error Error
erspan-kpa-valid Erspan kpa valid
ff Ff
frag frag
header-type Header type
ib-length-bundle Ib length bundle
ids-check-fail Ids-check-fail
ignore-acli Ignore-acli
ignore-aclo Ignore-aclo
ignore-qosi Ignore-qosi
ignore-qoso Ignore-qoso
inband-flow-creation-deletion Inband-flow-creation-deletion
index-direct Index-direct
inner-cos Inner-cos
inner-de-valid Inner de valid
inner-drop-eligibility Inner-drop-eligibility
ip-da-multicast Ip-da-multicast
ip-multicast Ip-multicast
ip-multicast-control Ip-multicast-control
ipv6 Ipv6
l2 L2
l2-frame-type L2-frame-type
l2-length-check L2 length check
l2lu-mode L2lu-mode
l3-packet-length l3 packet length
l4-protocol l4 protocol
label-count Label count
last-ethertype Last-ethertype
lbl0-eos Lbl0 eos
lbl0-exp Lbl0 exp
lbl0-lbl Lbl0 lbl
lbl0-ttl Lbl0 ttl
lbl0-valid Lbl0 valid
lbl1-exp Lbl1 exp
lbl1-ttl Lbl1 ttl
mac-in-mac-valid Mac-in-mac-valid
mc Mc
md-acos Md acos
md-destination-table-index Md destination table index
md-fwd-only Md fwd only
md-lif Md lif
md-mark-enable Md mark enable
md-multicast-bridge-disable Md multicast bridge disable
md-preserve-acos Md preserve acos
md-qos-group-id Md qos group id
md-replication-packet Md replication packet
md-router-mac Md router mac
md-ttl-err Md-ttl-err
md-version Md version
mf mf
mim-destination-mac-address Mim-destination-mac-address
mim-source-mac-address Mim-source-mac-address
mlh-type Mlh-type
no-stats No-stats
notify-index-learn Notify-index-learn
notify-new-learn Notify-new-learn
null-label-exp Null label exp
null-label-ttl Null label ttl
null-label-valid Null label valid
option option
outer-cos Outer-cos
outer-drop-eligibility Outer-drop-eligibility
ovl-mlh-bndl Ovl mlh bndl
ovl-ulh-bndl Ovl ulh bndl
ovl-ulh-bndl-1 Ovl-ulh-bndl-1
ovl-ulh-bndl-2 Ovl-ulh-bndl-2
packet-length Packet-length
packet-type Packet type
pdt-tag-gt-2 Pdt-tag-gt-2
pdt-tag0 Pdt-tag0
pdt-tag1 Pdt-tag1
pdt-valid Pdt-valid
pdt-value Pdt-value
port-id Port-id
rbh Rbh
rdt Rdt
recir-shim-vxlan-src-peer-id Recir shim vxlan src peer id
recirc-acos Recirc acos
recirc-bypass-ife Recirc bypass ife
recirc-bypass-l2 Recirc bypass l2
recirc-destination-table-index Recirc destination table index
recirc-forward-only Recirc forward only
recirc-l2-tunnel-encap Recirc l2 tunnel encap
recirc-lif Recirc lif
recirc-ls-hash Recirc ls hash
recirc-mark-enable Recirc mark enable
recirc-multicast-bridge-disable Recirc multicast bridge disable
recirc-preserve-acos Recirc preserve acos
recirc-preserve-ls-hash Recirc preserve ls hash
recirc-preserve-rbh Recirc preserve rbh
recirc-qos-group-id Recirc qos group id
recirc-replication-packet Recirc replication packet
recirc-router-mac Recirc router mac
recirc-ttl-err Recirc ttl err
recirc-valid Recirc-valid
recirc-version Recirc version
redirect Redirect
repl-bypass-ife Repl bypass ife
repl-bypass-l2 Repl bypass l2
repl-disable-local-bridge Repl disable local bridge
repl-fwd-only Repl fwd only
repl-l2-tunnel-encap Repl l2 tunnel encap
repl-l2-tunnel-info Repl l2 tunnel info
repl-lif Repl lif
repl-mark-enable Repl mark enable
repl-met-lif Repl met lif
repl-ml3 Repl ml3
repl-preserve-acos Repl preserve acos
repl-preserve-rbh Repl preserve rbh
repl-qos-group-id Repl qos group id
repl-replication-packet Repl replication packet
repl-router-mac Repl router mac
repl-ttl-err Repl ttl err
repl-version Repl version
rf Rf
second-inner-cos Second inner cos
segment-id Segment id
segment-id-valid Segment id valid
sequence-number Sequence-number
sg-tag Sg-tag
shim-valid Shim valid
source-index Source-index
source-ipv4-address source ipv4 address
source-mac-address Source-mac-address
source-vif Source-vif
status-ce-1q Status-ce-1q
status-is-1q Status-is-1q
sup-eid Sup-eid
tos tos
traceroute Traceroute
trig Any of previous elam triggered
trill-encap Trill-encap
ttl ttl
tunnel-bundle Tunnel bundle
tunnel-type Tunnel type
ulh-type Ulh-type
valid VALID
vl Vl
vlan Vlan
vn-p Vn p
vn-valid Vn-valid
vqi Vqi
vqi-valid Vqi-valid
vsl-num Vsl-num
module-3# elam asic flanker instance 0
module-3(fln-elam)# layer2
module-3(fln-l2-elam)# trigger dbus ipv4 ingress if source-ipv4-address 192.168.12.2
destination-ipv4-address 192.168.13.3
module-3(fln-l2-elam)# trigger rbus ingress if trig注意：RBUS配置通常不复杂且保持简单。
- 要检查触发器，请输入status命令，启动捕获进程，并启动从N7K2到N7K3（192.168.12.1到192.168.13.3）的ping:
module-3(fln-l2-elam)# stat
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 ingress if
source-ipv4-address 192.168.12.2 destination-ipv4-address 192.168.13.3
L2 DBUS: Configured
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus ingress if trig
L2 RBUS: Configured
module-3(fln-l2-elam)# start
module-3(fln-l2-elam)# status
!--- The status shows as Armed because the process has begun.
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 ingress if
source-ipv4-address 192.168.12.2 destination-ipv4-address 192.168.13.1
L2 DBUS: Armed
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus ingress if trig
L2 RBUS: Armed
module-3(fln-l2-elam)#
module-3(fln-l2-elam)# status
!--- If the packet is captured, the status shows Triggered.
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 ingress if
source-ipv4-address 192.168.12.2 destination-ipv4-address 192.168.13.3
L2 DBUS: Triggered
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus ingress if trig
L2 RBUS: Triggered
module-3(fln-l2-elam)# - 如果状态显示Triggered，则验证RBUS和DBUS是否具有相同的序列号，以确认它们是否用于同一数据包。在本例中，使用0x55，但显示序列号的列不同：
module-3(fln-l2-elam)# show dbus | in seq
sequence-number : 0x6b vl : 0x0
!--- The sequence number is the same (0x6b).
module-3(fln-l2-elam)# show rbus | in seq
l2-rbus-trigger : 0x1 sequence-number : 0x6b - 输入show dbus和show rbus命令以验证DBUS和RBUS。在DBUS命令输出中查找源索引，在RBUS命令输出中查找目标索引：
module-3(fln-l2-elam)# show dbus
cp = 0x1007db4c, buf = 0x1007db4c, end = 0x10089e9c
--------------------------------------------------------------------
Flanker Instance 00 - Capture Buffer On L2 DBUS:
Status(0x0102), TriggerWord(0x000), SampleStored(0x005),CaptureBufferPointer(0x005)
is_l2_egress: 0x0000, data_size: 0x023
[000]: 5902a000 08010000 00000000 0cc01400 00145800 00000000 01800100 00000000
00000000 00000000 003931c8 842850b9 31c88428 50c00000 01ac0000 00000000 00000000
00000000 00000000 00000000 00000005 80005000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00605406 01605406 8180008f f0054608 00000000
Printing packet 0
--------------------------------------------------------------------
L2 DBUS PRS MLH IPV4
--------------------------------------------------------------------
label-count : 0x0 mc : 0x0
null-label-valid : 0x0 null-label-exp : 0x0
null-label-ttl : 0x0 lbl0-vld : 0x0
lbl0-eos : 0x0 lbl0-lbl : 0x0
lbl0-exp : 0x0 lbl0-ttl : 0x0
lbl1-exp : 0x0 lbl1-ttl : 0x0
ipv4 : 0x0 ipv6 : 0x0
l4-protocol : 0x1 df : 0x0
mf : 0x0 frag : 0x0
ttl : 0xff l3-packet-length : 0x54
option : 0x0 tos : 0x0
sup-eid : 0x0 header-type : 0x1
error : 0x0 redirect : 0x0
port-id : 0x0 last-ethertype : 0x800
l2-frame-type : 0x0 da-type : 0x0
packet-type : 0x0 l2-length-check : 0x0
ip-da-multicast : 0x0 ip-multicast : 0x0
ip-multicast-control: 0x0 ids-check-fail : 0x0
traceroute : 0x0 outer-cos : 0x0
inner-cos : 0x0 vqi-valid : 0x0
vqi : 0x0 packet-length : 0x66
vlan : 0xa destination-index : 0x0
source-index : 0xa2c bundle-port : 0x0
acos : 0x0 outer-drop-eligibility: 0x0
inner-drop-eligibility: 0x0 sg-tag : 0x0
rbh : 0x0 vsl-num : 0x0
inband-flow-creation-deletion: 0x0 ignore-qoso : 0x0
ignore-qosi : 0x0 ignore-aclo : 0x0
ignore-acli : 0x0 index-direct : 0x0
no-stats : 0x0 dont-forward : 0x0
notify-index-learn : 0x1 notify-new-learn : 0x1
disable-new-learn : 0x0 disable-index-learn : 0x0
dont-learn : 0x0 bpdu : 0x0
ff : 0x0 rf : 0x0
ccc : 0x0 l2 : 0x0
rdt : 0x0 dft : 0x0
dfst : 0x0 status-ce-1q : 0x0
status-is-1q : 0x1 trill-encap : 0x0
mim-valid : 0x0 dtag-ttl : 0x0
dtag-ftag : 0x0 valid : 0x1
erspan-kpa-valid : 0x0 recir-shim-vxlan-src-peer-id: 0x0
vn-valid : 0x0 source-vif : 0x0
destination-vif : 0x0 vn-p : 0x0
sequence-number : 0x6b vl : 0x0
inner-de-valid : 0x0 de-cfi : 0x0
second-inner-cos : 0x0 tunnel-type : 0x0
shim-valid : 0x0
segment-id-valid : 0x0 copp : 0x0
dti-type-vpnid : 0x0 segment-id : 0x0
ib-length-bundle : 0x58000 mlh-type : 0x5
ulh-type : 0x6
source-ipv4-address: 192.168.12.2
destination-ipv4-address: 192.168.13.3
mim-destination-mac-address : 0000.0000.0000
mim-source-mac-address : 0000.0000.0000
destination-mac-address : e4c7.2210.a142
source-mac-address : e4c7.2210.a143
module-3(fln-l2-elam)# show rbus
cp = 0x100a2548, buf = 0x100a2548, end = 0x100ae898
--------------------------------------------------------------------
Flanker Instance 00 - Capture Buffer On L2 RBUS:
Status(0x0102), TriggerWord(0x000), SampleStored(0x005),CaptureBufferPointer(0x005)
is_l2_egress: 0x0000, data_size: 0x018
[000]: 0059d930 0000000c c0000000 03580000 00000000 00000000 0000001f 57b00021
fdfc0000 00000000 02000000 14001402 8b000105 00000000 68200000 00000000 00000000
00000400 00008000 005b0000 00fe0e4c 7220850a 210000a0 000000b6
Printing packet 0
--------------------------------------------------------------------
L2 RBUS INGRESS CONTENT
--------------------------------------------------------------------
pad : 0x16764 valid : 0x1
l2-rbus-trigger : 0x1 sequence-number : 0x6b
rit-ipv4-id : 0x0 ipv4-tunnel-encap : 0x0
rit-mpls-rw : 0x0 ml2-ptr : 0x0
ml3-ptr : 0x0 mark : 0x0
result-cap3 : 0x0 di1-v5-delta-length : 0x0
di1-v5-delta-length-plus: 0x0 di1-v4-delta-length : 0x0
di1-v4-delta-length-plus: 0x0 di2-delta-length : 0x0
di2-delta-length-plus: 0x0 ml2-delta-length : 0x0
ml2-delta-length-plus: 0x0 ml3-delta-length : 0x0
ml3-delta-length-plus: 0x0 s-vector : 0x0
lcpu-ff-valid : 0x0 sup-di-vqi : 0x0
erspan-term-index-dir: 0x0 erspan-buffer-check : 0x0
l2-tunnel-decapped : 0x0 l3-delta-length : 0x0
rit-crc16-valid : 0x1 rit-crc16 : 0xf57b
vntag-p : 0x0 frr-recirc : 0x0
ingress-lif : 0x1 earl-proxy-vld : 0x0
md-di-vld : 0x0 rc : 0x0
segment-id-valid : 0x0 ttl-out : 0xfe
ttl-mid : 0xfe tos-out : 0x0
tos-in : 0x0 orig-vlan1 : 0x0
vlan1 : 0x0 source-peer-id : 0x0
final-ignore-qoso : 0x0 port-id : 0x0
cr-type : 0x1 pup-packet : 0x0
bpdu : 0x0 vdc : 0x0
traceroute : 0x0 de : 0x0
cos : 0x0 inner-drop-eligibility: 0x0
inner-cos : 0x0 acos : 0x0
di-ltl-index : 0x50 l3-multicast-di : 0x50
source-index : 0xa2c vlan : 0x0
index-direct : 0x0 di1-valid : 0x1
vqi : 0x50 di2-valid : 0x0
v5-fpoe-idx : 0x0 di2-fpoe-idx : 0x0
l3-multicast-v5 : 0x0 dft : 0x0
dfst : 0x0 l3-learning-ff : 0x0
result-rbh : 0xd0 di2-cr-type : 0x0
result-2 : 0x1 dtag-ftag : 0x0
dtag-ttl : 0x20 mac-in-mac-op : 0x0
dvif : 0x0 result-cap1 : 0x0
result-cap2 : 0x0 erspan-term : 0x0
erspan-decap : 0x0 dont-learn : 0x0
routed-frame : 0x1 copy-cause : 0x0
l2-copy-cause : 0x0 l3-rit-ptr : 0x5b
sg-tag : 0x0 trill-nh-id : 0x0
ttl-in : 0xfe fc-up : 0x0
up-did : 0x0 did : 0xe4c722
up-sid : 0x0 sid : 0x10a144
shim-l2-tunnel-encap: 0x0 shim-ls-hash : 0x8
shim-rc : 0x0 shim-lif : 0x1
shim-replication-pkt: 0x0 shim-router-mac : 0x1
shim-mark-enable : 0x0 shim-qos-group-id : 0x0
shim-destination-table-index: 0x5b shim-acos-preserve : 0x0
mim-destination-mac-address : 0000.0000.0000
mim-source-mac-address : 0000.0000.0000 - 在Sup:
N7K1# show system internal pixm info ltl 0xa2c
此输出确认数据包是在端口通道1(Po1)上接收并通过Eth3/5转发的。
PC_TYPE PORT LTL RES_ID LTL_FLAG CB_FLAG MEMB_CNT
------------------------------------------------------------------------------
Normal Po1 0x0a2c 0x16000000 0x00000000 0x00000002 2
Member rbh rbh_cnt
Eth3/2 0x000000f0 0x04
Eth3/1 0x0000000f 0x04
CBL Check States: Ingress: Enabled; Egress: Enabled
VLAN| BD| BD-St | CBL St & Direction:
--------------------------------------------------
1 | 0x15 | INCLUDE_IF_IN_BD | FORWARDING (Both)
10 | 0x19 | INCLUDE_IF_IN_BD | FORWARDING (Both)
Member info
------------------
Type LTL
---------------------------------
PORT_CHANNEL Po1
FLOOD_W_FPOE 0x8019
FLOOD_W_FPOE 0x8015
N7K1# show system internal pixm info ltl 0x50
0x0050 is in DCE/FC pool
Member info
------------------
Type LTL
---------------------------------
PHY_PORT Eth3/5 - 验证模块上的本地目标逻辑(LTL)以获取正确的编程：
module-3# show system internal pixmc info ltl-cb ltl 0xa2c
ltl |ltl_type|if_index|lc_type| vdc |v4_fpoe|v5_fpoe| base_fpoe_idx | flag
0x0a2c | 4 | Po1 | 2 | 2 | 0x00 | 0x00 | 0x0000 | 0x0
, local ports:
VDCs the entry is part of:
LTL HW programming info
.......................
----------------------------------------------------
|Index | ec |drop|span_vec|SOM|ucr_fab|
|--------------------------------------------------
|[ a2c]| 1| 0| 0| 0| 0|
| RBH | VQI | PS(INST:LPOE)
|----------------------------------
0, 40 0 : 1
1, 40 0 : 1
2, 40 0 : 1
3, 40 0 : 1
4, 44 0 : 10
5, 44 0 : 10
6, 44 0 : 10
7, 44 0 : 10
8, 0 0 : 1
9, 0 0 : 1
a, 0 0 : 1
b, 0 0 : 1
c, 0 0 : 10
d, 0 0 : 10
e, 0 0 : 10
f, 0 0 : 10
module-3# show system internal pixmc info ltl-cb ltl 0x50
ltl |ltl_type|if_index|lc_type| vdc |v4_fpoe | v5_fpoe| base_fpoe_idx | flag
0x0050 | 5 |Eth3/5 | 2 | 2 | 0x00 | 0x00 | 0x0000 | 0x0
, local ports:
VDCs the entry is part of:
LTL HW programming info
.......................
----------------------------------------------------
|Index | ec |drop|span_vec|SOM|ucr_fab|
|--------------------------------------------------
|[ 50]| 1| 0| 0| 0| 0|
| RBH | VQI | PS
|----------------------------
ALL RBH| 50 | 2 : 1 - 在出口时捕获ELAM数据包。要捕获数据包，请从IP地址192.168.13.3发送ping应答到192.168.12.2。必须在端口通道1接口(e3/1-2)上使用egress关键字设置捕获。 如前所述，接口属于实例0。
N7K1# att mo 3
如图所示，源索引和目标索引都是DBUS的一部分（与入口捕获中显示的不同）。
Attaching to module 3 ...
To exit type 'exit', to abort type '$.'
module-3# el asic flanker instance 0
module-3(fln-elam)# layer2
module-3(fln-l2-elam)# trigger dbus ipv4 egress if source-ipv4-address 192.168.13.3
destination-ipv4-address 192.168.12.2
module-3(fln-l2-elam)# trigger rbus egress if trig
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.13.3 destination-ipv4-address 192.168.12.2
L2 DBUS: Configured
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Configured
module-3(fln-l2-elam)# start
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.13.3 destination-ipv4-address 192.168.12.2
L2 DBUS: Armed
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Armed
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 0: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.13.3 destination-ipv4-address 192.168.12.2
L2 DBUS: Triggered
ELAM Slot 3 instance 0: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Triggered
module-3(fln-l2-elam)#
module-3(fln-l2-elam)# show dbus | in seq
sequence-number : 0x8d vl : 0x3
!--- The sequence number is the same.
module-3(fln-l2-elam)# show rbus | in seq
vl : 0x0 sequence-number : 0x8d
module-3(fln-l2-elam)# show dbus
cp = 0x1007db4c, buf = 0x1007db4c, end = 0x10089e9c
--------------------------------------------------------------------
Flanker Instance 00 - Capture Buffer On L2 DBUS:
Status(0x0102), TriggerWord(0x000), SampleStored(0x005),CaptureBufferPointer(0x005)
is_l2_egress: 0x0000, data_size: 0x023
[000]: 48c22000 08210000 40020800 0cc01414 5800a000 00001a40 01030000 00000000
00000000 00000000 003931c8 842850f9 31c88428 50800000 02358000 00000000 00000000
00000000 00000000 00000000 00000000 00005000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00605406 81e05406 0100008f e0054600 00000000
Printing packet 0
--------------------------------------------------------------------
L2 DBUS PRS MLH IPV4
--------------------------------------------------------------------
label-count : 0x0 mc : 0x0
null-label-valid : 0x0 null-label-exp : 0x0
null-label-ttl : 0x0 lbl0-vld : 0x0
lbl0-eos : 0x0 lbl0-lbl : 0x0
lbl0-exp : 0x0 lbl0-ttl : 0x0
lbl1-exp : 0x0 lbl1-ttl : 0x0
ipv4 : 0x0 ipv6 : 0x0
l4-protocol : 0x1 df : 0x0
mf : 0x0 frag : 0x0
ttl : 0xfe l3-packet-length : 0x54
option : 0x0 tos : 0x0
sup-eid : 0x0 header-type : 0x1
error : 0x0 redirect : 0x0
port-id : 0x1 last-ethertype : 0x800
l2-frame-type : 0x0 da-type : 0x0
packet-type : 0x1 l2-length-check : 0x0
ip-da-multicast : 0x0 ip-multicast : 0x0
ip-multicast-control: 0x0 ids-check-fail : 0x0
traceroute : 0x0 outer-cos : 0x0
inner-cos : 0x0 vqi-valid : 0x1
vqi : 0x40 packet-length : 0x66
vlan : 0xa destination-index : 0xa2c
source-index : 0x50 bundle-port : 0x0
acos : 0x0 outer-drop-eligibility: 0x0
inner-drop-eligibility: 0x0 sg-tag : 0x0
rbh : 0xd2 vsl-num : 0x0
inband-flow-creation-deletion: 0x0 ignore-qoso : 0x0
ignore-qosi : 0x0 ignore-aclo : 0x0
ignore-acli : 0x0 index-direct : 0x0
no-stats : 0x0 dont-forward : 0x0
notify-index-learn : 0x1 notify-new-learn : 0x0
disable-new-learn : 0x0 disable-index-learn : 0x0
dont-learn : 0x0 bpdu : 0x0
ff : 0x0 rf : 0x1
ccc : 0x4 l2 : 0x0
rdt : 0x0 dft : 0x0
dfst : 0x0 status-ce-1q : 0x0
status-is-1q : 0x0 trill-encap : 0x0
mim-valid : 0x0 dtag-ttl : 0x0
dtag-ftag : 0x0 valid : 0x1
erspan-kpa-valid : 0x0 recir-shim-vxlan-src-peer-id: 0x0
vn-valid : 0x0 source-vif : 0x0
destination-vif : 0x0 vn-p : 0x0
sequence-number : 0x8d vl : 0x3
inner-de-valid : 0x0 de-cfi : 0x0
second-inner-cos : 0x0 tunnel-type : 0x0
shim-valid : 0x0
segment-id-valid : 0x0 copp : 0x0
dti-type-vpnid : 0x0 segment-id : 0x0
ib-length-bundle : 0x0 mlh-type : 0x5
ulh-type : 0x6
source-ipv4-address: 192.168.13.3
destination-ipv4-address: 192.168.12.2
mim-destination-mac-address : 0000.0000.0000
mim-source-mac-address : 0000.0000.0000
destination-mac-address : e4c7.2210.a143
source-mac-address : e4c7.2210.a142
module-3(fln-l2-elam)# show rbus
源IP地址和目的IP地址正确，在入口ELAM数据包捕获后解码；但是，与入口ELAM相比，方向肯定相反，因为返回流量被捕获。
cp = 0x100a2548, buf = 0x100a2548, end = 0x100ae898
--------------------------------------------------------------------
Flanker Instance 00 - Capture Buffer On L2 RBUS:
Status(0x1102), TriggerWord(0x000), SampleStored(0x008),CaptureBufferPointer(0x000)
is_l2_egress: 0x0001, data_size: 0x018
[000]: 0048ea00 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 0c000000 00000000 04014008 00005000 00000000
00000726 3910850a 1b931c88 42850800 00000000 00000000 0000008d
Printing packet 0
--------------------------------------------------------------------
L2 RBUS EGRESS CONTENT
--------------------------------------------------------------------
pad : 0x0 valid : 0x1
trig : 0x1 reserved : 0x0
vn-tag-p : 0x0 cbl-vlan-valid : 0x0
vft-hop-count : 0x0 vft-vsan : 0x0
vft-up : 0x0 vft-valid : 0x0
copp : 0x0 segment-id-valid : 0x0
segment-id-23 : 0x0 vsl-num : 0x0
inner-cos : 0x0 inner-drop-eligibility: 0x0
cos : 0x0 drop-eligibility : 0x0
dce-mode : 0x0 flood-to-bd : 0x0
pt-bit-en : 0x1 cpu-port : 0x0
vlan-id : 0xa ip-tos : 0x0
result-rbh : 0x1 met-ptr : 0x2000
packet-type : 0x1 sg-tag : 0x0
dtag-ftag : 0x0 vdc : 0x0
vn-tag-src-vif : 0x0 vn-tag-dst-vif : 0x0
vn-tag-l : 0x0 dc3-tr : 0x0
vl : 0x0 sequence-number : 0x8d
destination-mac-valid: 0x0
source-mac-valid: 0x0
mim-destination-mac-address : 0000.0000.0000
destination-mac-address : e4c7.2210.a143
source-mac-address : e4c7.2210.a142
mim-source-mac-address : 0000.0000.0000 - 检查N7K1上端口通道1模块3的基于颜色的逻辑(CBL)，以确定VLAN 10是否通过它转发流量。CBL是基于每个物理接口的逻辑，因此您应输入N7K1上端口通道1的成员接口编号，而不是端口通道编号。在下一个输出中，您可以看到VLAN 10按预期转发它。
CBL用于确定硬件中端口的生成树协议(STP)状态。当您检查SP上VLAN的STP时，接口可能显示转发，但模块会阻止流量。注意：必须分别检查两个成员接口（e3/1和e3/2）的CBL。
module-3# show hardware internal mac port 1 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-9,11-4031,4036-4095 |
| Forwarding State | 1,10,4032-4035 |
| Blocked State | |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-9,11-4031,4036-4095 |
| Forwarding State | 1,10,4032-4035 |
| Blocked State | |
| Learning State | |
--------------------------------------------------------------------------------注意：以前的命令用于端口通道1(模块3在e3/1上)。
module-3# show hardware internal mac port 2 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-9,11-4031,4036-4095 |
| Forwarding State | 1,10,4032-4035 |
| Blocked State | |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-9,11-4031,4036-4095 |
| Forwarding State | 1,10,4032-4035 |
| Blocked State | |
| Learning State | |
--------------------------------------------------------------------------------注意：同样，此命令会检查端口通道2(e3/2)的CBL。
使用分支电缆对F3系列模块上的ELAM进行故障排除
连接分支电缆时F3系列模块的ELAM程序与常规模块端口上的ELAM程序无异。但是，在尝试将索引转换为前面板编号时，端口索引管理器(PIXM)的验证有一些变化，在这种情况下，接口会从分支电缆接收。
以下是本节中用于示例的拓扑：
+------------+ BreakOut Cable +-----------+
| | e3/8/1-4 te1/1| |
| | +-----------+ |
| |e3/8 | 1/2 | 4500-X |
| N7K3 +----------------------+ |
| | Po2 | 1/3 | |
| | +-----------+ |
| | | 1/4 | |
+------------+ +-----------+-----------+
Vlan20 SVI Vlan20 SVI
IP add 192.168.20.3 IP add 192.168.20.1
在本例中，分支电缆连接到以太网接口3/8，这将40 Gb端口分为四个10 Gb端口。本部分提供了所需的配置以供参考。
N7K3(config)# interface breakout module 3 port 8 map 10g-4x
N7K3(config)# show interface brief
---SNIP---
---------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch #
---------------------------------------------------------------
Eth3/7 -- eth routed up none 40G(D) --
Eth3/8/1 1 eth trunk up none 10G(D) 2
!--- From 3/8/1 to 3/8/4.
Eth3/8/2 1 eth trunk up none 10G(D) 2
Eth3/8/3 1 eth trunk up none 10G(D) 2
Eth3/8/4 1 eth trunk up none 10G(D) 2
在上一输出中，您可以看到以太网接口3/7仍是一个40 Gb端口；但是，以太网接口3/8现在分为四个万兆端口，可单独配置：
N7K3# show run interface e3/8/1 - 4
!Command: show running-config interface Ethernet3/8/1-4
!Time: Mon May 4 01:46:28 2015
version 6.2(8a)
interface Ethernet3/8/1
switchport
switchport mode trunk
switchport trunk allowed vlan 10,20
no shutdown
interface Ethernet3/8/2
switchport
switchport mode trunk
switchport trunk allowed vlan 30,40
no shutdown
interface Ethernet3/8/3
switchport
switchport mode trunk
switchport trunk allowed vlan 50
no shutdown
interface Ethernet3/8/4
switchport
switchport mode trunk
no shutdown
从N7K3交换虚拟接口(SVI)20 IP地址(192.168.20.3)开始数据包捕获到4500 SVI 20 IP地址(192.168.20.1)。 数据包将在N7K3上从4500出口捕获，应答从4500发送到N7K3。
如上节所述，您必须了解flanker实例才能应用触发器。此输出显示模块3的附件：
N7K3# attach module 3
Attaching to module 3 ...
To exit type 'exit', to abort type '$.'
module-3# show hardware internal dev
dev-port-map dev-version
module-3# show hardware internal dev-port-map
--------------------------------------------------------------
CARD_TYPE: 12 port 40G
>Front Panel ports:12
--------------------------------------------------------------
Device name Dev role Abbr num_inst:
--------------------------------------------------------------
> Flanker Eth Mac Driver DEV_ETHERNET_MAC MAC_0 6
> Flanker Fwd Driver DEV_LAYER_2_LOOKUP L2LKP 6
> Flanker Xbar Driver DEV_XBAR_INTF XBAR_INTF 6
> Flanker Queue Driver DEV_QUEUEING QUEUE 6
> Sacramento Xbar ASIC DEV_SWITCH_FABRIC SWICHF 1
> Flanker L3 Driver DEV_LAYER_3_LOOKUP L3LKP 6
> EDC DEV_PHY PHYS 2
+-----------------------------------------------------------------------+
+----------------+++FRONT PANEL PORT TO ASIC INSTANCE MAP+++------------+
+-----------------------------------------------------------------------+
FP port | PHYS | MAC_0 | L2LKP | L3LKP | QUEUE |SWICHF
1 0 0 0 0 0
2 0 0 0 0 0
3 1 1 1 1 0
4 1 1 1 1 0
5 0 2 2 2 2 0
6 0 2 2 2 2 0
7 1 3 3 3 3 0
8 1 3 3 3 3 0
!--- The port 8 L2LKP column shows a value of 3.
9 4 4 4 4 0
10 4 4 4 4 0
11 5 5 5 5 0
12 5 5 5 5 0
+-----------------------------------------------------------------------+
+-----------------------------------------------------------------------+
在此输出中，端口8位于Flanker实例3上。现在您知道该实例，可以通过源和目标IP地址放置触发器。由于您将捕获从N7K3到4500的ping请求，因此它将是出口ELAM。
module-3# elam asic flanker instance 3
module-3(fln-elam)# layer2
module-3(fln-l2-elam)# trigger dbus ipv4 egress if source-ipv4-address 192.168.20.3
destination-ipv4-address 192.168.20.1
module-3(fln-l2-elam)# trigger rbus egress if trig
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 3: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.20.3 destination-ipv4-address 192.168.20.1
L2 DBUS: Configured
ELAM Slot 3 instance 3: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Configured
module-3(fln-l2-elam)# start
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 3: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.20.3 destination-ipv4-address 192.168.20.1
L2 DBUS: Armed
ELAM Slot 3 instance 3: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Armed
从N7K3向4500发起ping:
N7K3# ping 192.168.20.1
PING 192.168.20.1 (192.168.20.1): 56 data bytes
36 bytes from 192.168.20.3: Destination Host Unreachable
Request 0 timed out
64 bytes from 192.168.20.1: icmp_seq=1 ttl=254 time=6.49 ms
64 bytes from 192.168.20.1: icmp_seq=2 ttl=254 time=6.518 ms
64 bytes from 192.168.20.1: icmp_seq=3 ttl=254 time=7.936 ms
64 bytes from 192.168.20.1: icmp_seq=4 ttl=254 time=7.945 ms
--- 192.168.20.1 ping statistics ---
5 packets transmitted, 4 packets received, 20.00% packet loss
round-trip min/avg/max = 6.49/7.222/7.945 ms
以下是ELAM状态：
module-3(fln-l2-elam)# status
ELAM Slot 3 instance 3: L2 DBUS Configuration: trigger dbus ipv4 egress if
source-ipv4-address 192.168.20.3 destination-ipv4-address 192.168.20.1
L2 DBUS: Triggered
ELAM Slot 3 instance 3: L2 RBUS Configuration: trigger rbus egress if trig
L2 RBUS: Triggered
验证序列号是否相同：
module-3(fln-l2-elam)# show dbus | in seq
sequence-number : 0x27 vl : 0x3
module-3(fln-l2-elam)# show rbus | in seq
vl : 0x0 sequence-number : 0x27
序列号相同。现在，您可以检查DBUS和RBUS信息：
module-3(fln-l2-elam)# show dbus
cp = 0x1011033c, buf = 0x1011033c, end = 0x1011c68c
--------------------------------------------------------------------
Flanker Instance 03 - Capture Buffer On L2 DBUS:
Status(0x0102), TriggerWord(0x000), SampleStored(0x004),CaptureBufferPointer(0x004)
is_l2_egress: 0x0000, data_size: 0x023
[000]: 4c1ea000 20a10000 40021040 0cc02801 04080000 00000000 08100000 00000000
00000000 00000000 003c1fc1 8732dff9 31c88428 51000000 009d8000 00000000 00000000
00000000 00000000 00000000 00000000 00005000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 0060540a 01e0540a 0080008f f0054608 00000000
Printing packet 0
--------------------------------------------------------------------
L2 DBUS PRS MLH IPV4
--------------------------------------------------------------------
label-count : 0x0 mc : 0x0
null-label-valid : 0x0 null-label-exp : 0x0
null-label-ttl : 0x0 lbl0-vld : 0x0
lbl0-eos : 0x0 lbl0-lbl : 0x0
lbl0-exp : 0x0 lbl0-ttl : 0x0
lbl1-exp : 0x0 lbl1-ttl : 0x0
ipv4 : 0x0 ipv6 : 0x0
l4-protocol : 0x1 df : 0x0
mf : 0x0 frag : 0x0
ttl : 0xff l3-packet-length : 0x54
option : 0x0 tos : 0x0
sup-eid : 0x1 header-type : 0x0
error : 0x0 redirect : 0x0
port-id : 0x5 last-ethertype : 0x800
l2-frame-type : 0x0 da-type : 0x0
packet-type : 0x1 l2-length-check : 0x0
ip-da-multicast : 0x0 ip-multicast : 0x0
ip-multicast-control: 0x0 ids-check-fail : 0x0
traceroute : 0x0 outer-cos : 0x0
inner-cos : 0x0 vqi-valid : 0x1
vqi : 0x82 packet-length : 0x66
vlan : 0x14 destination-index : 0x82
source-index : 0x400 bundle-port : 0x0
acos : 0x0 outer-drop-eligibility: 0x0
inner-drop-eligibility: 0x0 sg-tag : 0x0
rbh : 0x0 vsl-num : 0x0
inband-flow-creation-deletion: 0x0 ignore-qoso : 0x0
ignore-qosi : 0x0 ignore-aclo : 0x0
ignore-acli : 0x0 index-direct : 0x1
no-stats : 0x0 dont-forward : 0x0
notify-index-learn : 0x0 notify-new-learn : 0x0
disable-new-learn : 0x0 disable-index-learn : 0x0
dont-learn : 0x1 bpdu : 0x0
ff : 0x0 rf : 0x0
ccc : 0x0 l2 : 0x0
rdt : 0x0 dft : 0x0
dfst : 0x0 status-ce-1q : 0x0
status-is-1q : 0x0 trill-encap : 0x0
mim-valid : 0x0 dtag-ttl : 0x0
dtag-ftag : 0x0 valid : 0x1
erspan-kpa-valid : 0x0 recir-shim-vxlan-src-peer-id: 0x0
vn-valid : 0x0 source-vif : 0x0
destination-vif : 0x0 vn-p : 0x0
sequence-number : 0x27 vl : 0x3
inner-de-valid : 0x0 de-cfi : 0x0
second-inner-cos : 0x0 tunnel-type : 0x0
shim-valid : 0x0
segment-id-valid : 0x0 copp : 0x0
dti-type-vpnid : 0x0 segment-id : 0x0
ib-length-bundle : 0x0 mlh-type : 0x5
ulh-type : 0x6
source-ipv4-address: 192.168.20.3
destination-ipv4-address: 192.168.20.1
mim-destination-mac-address : 0000.0000.0000
mim-source-mac-address : 0000.0000.0000
destination-mac-address : f07f.061c.cb7f
source-mac-address : e4c7.2210.a144
module-3(fln-l2-elam)#
module-3(fln-l2-elam)#
module-3(fln-l2-elam)#
module-3(fln-l2-elam)# show rbus
cp = 0x10134d38, buf = 0x10134d38, end = 0x10141088
--------------------------------------------------------------------
Flanker Instance 03 - Capture Buffer On L2 RBUS:
Status(0x1102), TriggerWord(0x000), SampleStored(0x008),CaptureBufferPointer(0x000)
is_l2_egress: 0x0001, data_size: 0x018
[000]: 004c4780 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 0c001000 00000000 80028010 00009000 00000000
00000783 f830e65b fb931c88 42851000 00000000 00000000 00000027
Printing packet 0
--------------------------------------------------------------------
L2 RBUS EGRESS CONTENT
--------------------------------------------------------------------
pad : 0x0 valid : 0x1
trig : 0x1 reserved : 0x0
vn-tag-p : 0x1 cbl-vlan-valid : 0x0
vft-hop-count : 0x0 vft-vsan : 0x0
vft-up : 0x0 vft-valid : 0x0
copp : 0x0 segment-id-valid : 0x0
segment-id-23 : 0x0 vsl-num : 0x0
inner-cos : 0x0 inner-drop-eligibility: 0x0
cos : 0x0 drop-eligibility : 0x0
dce-mode : 0x0 flood-to-bd : 0x0
pt-bit-en : 0x20 cpu-port : 0x0
vlan-id : 0x14 ip-tos : 0x0
result-rbh : 0x2 met-ptr : 0x4000
packet-type : 0x1 sg-tag : 0x0
dtag-ftag : 0x0 vdc : 0x0
vn-tag-src-vif : 0x0 vn-tag-dst-vif : 0x0
vn-tag-l : 0x0 dc3-tr : 0x0
vl : 0x0 sequence-number : 0x27
destination-mac-valid: 0x0
source-mac-valid: 0x0
mim-destination-mac-address : 0000.0000.0000
destination-mac-address : f07f.061c.cb7f
source-mac-address : e4c7.2210.a144
mim-source-mac-address : 0000.0000.0000
将目标索引和源索引转换为前面板端口以确认流：
N7K3# show system internal pixm info ltl 0x400
0x0400 is in SUP In-band LTL range
此输出显示源索引。您知道这是正确的，因为从Sup到N7K3的ping操作。下一个输出显示出出口接口(e3/8/1)，它是N7K上允许VLAN 20的两个接口之一。另一个接口是e3/8/4，由于STP而在4500上被阻塞。
N7K3# show system internal pixm info ltl 0x82
0x0082 is in DCE/FC pool
Member info
------------------
Type LTL
---------------------------------
PHY_PORT Eth3/8/1
FLOOD_W_FPOE 0x8039
FLOOD_W_FPOE 0x803f
验证N7K上使用分支电缆创建的端口的电缆。要检查CBL，您必须拥有所有新形成端口的硬件端口号。
注意：交换机上不存在接口e3/8。仅显示新形成的端口。
N7K3# show interface e3/8
^
% Incomplete command at '^' marker.
N7K3#
由于使用了分支电缆，并且交换机上不存在e3/8接口，因此用于获取硬件端口号的计算会发生变化。对于任何支持分支的模块，硬件端口编号都不同。您应首先检查端口是否支持分支：
N7K3# show int e3/7 capabilities
Ethernet3/7
Model: N7K-F312FQ-25
Type (SFP capable): QSFP-40G-CR4
Speed: 10000,40000
Duplex: full
---SNIP---
PFC capable: yes
Breakout capable: yes
如图所示，端口e3/7支持分支，这意味着其带宽可分为四个万兆端口。同样，其他具有100千兆端口的F3系列模块可分为10个每个10千兆端口或3个40千兆超订用端口。具体情况取决于模块。
由于本示例中的F3系列模块有40千兆端口，并且每个端口可分为四个端口，因此每个端口的硬件端口号是0-3、4-7、8-11...40-43、44-47（以零为基数）。如果第一个示例的端口上有分支电缆，则其硬件端口编号为0、1、2和3。如果没有分支电缆，则其硬件端口编号为0（1、2和3将不活动）。
由于父端口是e3/8，如果不使用分支电缆，则其硬件端口号为28；如果与分支电缆一起使用，则其硬件端口号为28、29、30和31。此命令输出显示活动硬件端口（基于零）：
N7K3# show system internal ifindex info mod 3
Init DB dump follows:
module_num_bitmask = 0x3ffff
Slot:3, Proc:1, breakout_factor:0, sw_card_id:0, active_cfg_ports:, broken_fp_po
rts:
Slot:3, Proc:2, breakout_factor:4, sw_card_id:155, active_cfg_ports:0,4,8,12,16,
20,24,28-32,36,40,44, broken_fp_ports:28
Lookup DB dump follows:
Slot:3, breakout_factor:4
损坏的端口硬件端口号为28，现在分为四个(28-32)。 现在，您可以连接模块3并检查硬件中的电缆：
N7K3# attach module 3
Attaching to module 3 ...
To exit type 'exit', to abort type '$.'
module-3#
F3系列模块希望端口号按照基于一的比例进行格式化。因此，您应输入29、30、31和32:
module-3# show hardware internal mac port ?
<1-96> Port number (1-based)
!--- This is context sensitive, so it helps to say the port number is 1-based.
以下是以太网接口3/8/1的运行配置，以便检查和确认VLAN转发状态：
interface Ethernet3/8/1
switchport
switchport mode trunk
switchport trunk allowed vlan 10,20
no shutdown
module-3# show hardware internal mac port 29 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-9,11-19,21-4031,4036-4095 |
| Forwarding State | 10,20,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-9,11-19,21-4031,4036-4095 |
| Forwarding State | 10,20,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
以下是以太网接口3/8/2的运行配置，以便检查和确认VLAN转发状态：
interface Ethernet3/8/2
switchport
switchport mode trunk
switchport trunk allowed vlan 30,40
no shutdown
module-3# show hardware internal mac port 30 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-29,31-39,41-4031,4036-4095 |
| Forwarding State | 30,40,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-29,31-39,41-4031,4036-4095 |
| Forwarding State | 30,40,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
以下是以太网接口3/8/3的运行配置，以便检查和确认VLAN转发状态：
interface Ethernet3/8/3
switchport
switchport mode trunk
switchport trunk allowed vlan 50
no shutdown
module-3# show hardware internal mac port 31 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-49,51-4031,4036-4095 |
| Forwarding State | 50,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-49,51-4031,4036-4095 |
| Forwarding State | 50,4032-4035 |
| Blocked State | 1 |
| Learning State | |
--------------------------------------------------------------------------------
以下是以太网接口3/8/4的运行配置，用于检查和确认VLAN转发状态（允许所有已配置的VLAN）：
interface Ethernet3/8/4
switchport
switchport mode trunk
no shutdown
module-3# show hardware internal mac port 32 table cbl vlan
--------------------------------------------------------------------------------
| INGRESS |
| Disabled State | 0,2-9,11-19,21-29,31-39,41-49,51-59,61-669,671-4031 |
| Disabled State | 4036-4095 |
| Forwarding State | 1,20,30,40,50,60,670,4032-4035 |
| Blocked State | 10 |
| Learning State | |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| EGRESS |
| Disabled State | 0,2-9,11-19,21-29,31-39,41-49,51-59,61-669,671-4031 |
| Disabled State | 4036-4095 |
| Forwarding State | 1,20,30,40,50,60,670,4032-4035 |
| Blocked State | 10 |
| Learning State | |
--------------------------------------------------------------------------------
CBL显示转发了正确的VLAN。
可以使用show hardware internal error module <module number>命令来获取硬件端口号。当您必须检查show interface x/y命令输出中未显示的任何内部丢弃时，此命令非常有用。示例如下：
N7K2# show hardware internal errors module 3
---SNIP---
Instance:1
Cntr Name Value Ports
----- ---- ----- -----
3836 igr rx pl: cbl drops 0000000000000001 10 -
4636 igr rx pl: cbl drops 0000000000000001 14 -
Instance:2
Cntr Name Value Ports
----- ---- ----- -----
423 igr in upm: pkts with symbol/sequence error rcvd 0000000000000478 18 -
455 igr in upm: pkts with symbol/sequence error rcvd 0000000000000478 17 -
487 igr in upm: pkts with symbol/sequence error rcvd 0000000000000478 19 -
519 igr in upm: pkts with symbol/sequence error rcvd 0000000000000478 20 -
Instance:3
Cntr Name Value Ports
----- ---- ----- -----
423 igr in upm: pkts with symbol/sequence error rcvd 0000000000000745 26 -
455 igr in upm: pkts with symbol/sequence error rcvd 0000000000000745 25 -
487 igr in upm: pkts with symbol/sequence error rcvd 0000000000000745 27 -
519 igr in upm: pkts with symbol/sequence error rcvd 0000000000000745 28 -
550 igr in upm: pkts rcvd, with RCODE violation 0000359810913821 30 -
551 igr in upm: pkts with symbol/sequence error rcvd 0000425092490108 30 -
552 igr in upm: pkts with error 0000000000176136 30 -
582 igr in upm: pkts rcvd, with RCODE violation 0000000000292641 29 -
583 igr in upm: pkts with symbol/sequence error rcvd 0000000000114014 29 -
614 igr in upm: pkts rcvd, with RCODE violation 0000133362265995 31 -
615 igr in upm: pkts with symbol/sequence error rcvd 0000146701474013 31 -
616 igr in upm: pkts with error 0000000000157479 31 -
646 igr in upm: pkts rcvd, with RCODE violation 0000000002160959 32 -
647 igr in upm: pkts with symbol/sequence error rcvd 0000000003722562 32 -
648 igr in upm: pkts with error 0000000000000002 32 -
由思科工程师提供
- Mohammed NijamuddinCisco TAC Engineer
反馈