PIX/ASA 7.x PIX para PIX IPsec dinâmico para estático com NAT e exemplo de configuração de cliente VPN

Opções de download

  • PDF     (162.9 KB)
    Ver no Adobe Reader em vários dispositivos
  • ePub     (102.5 KB)
    Ver em vários aplicativos no iPhone, iPad, Android, Sony Reader ou Windows Phone
  • Mobi (Kindle)     (129.5 KB)
    Ver no dispositivo Kindle ou no aplicativo Kindle em vários dispositivos
Atualizado:3 de maio de 2007
ID do documento:63876

Linguagem imparcial

O conjunto de documentação deste produto faz o possível para usar uma linguagem imparcial. Para os fins deste conjunto de documentação, a imparcialidade é definida como uma linguagem que não implica em discriminação baseada em idade, deficiência, gênero, identidade racial, identidade étnica, orientação sexual, status socioeconômico e interseccionalidade. Pode haver exceções na documentação devido à linguagem codificada nas interfaces de usuário do software do produto, linguagem usada com base na documentação de RFP ou linguagem usada por um produto de terceiros referenciado. Saiba mais sobre como a Cisco está usando a linguagem inclusiva.

Sobre esta tradução

A Cisco traduziu este documento com a ajuda de tecnologias de tradução automática e humana para oferecer conteúdo de suporte aos seus usuários no seu próprio idioma, independentemente da localização. Observe que mesmo a melhor tradução automática não será tão precisa quanto as realizadas por um tradutor profissional. A Cisco Systems, Inc. não se responsabiliza pela precisão destas traduções e recomenda que o documento original em inglês (link fornecido) seja sempre consultado.

Introduction

Na maioria dos casos, um PIX remoto que se conecta a um PIX central não usa a tradução de endereço de rede (NAT). Em vez disso, o PIX remoto usa um endereço IP estático externo. Por exemplo, quando um PIX central que executa a versão 7.x ou posterior se conecta a um PIX remoto que usa NAT, ele se torna igual a um home office pequeno como um PIX 501 ou 506 conectado a um cabo ou modem DSL usando Dynamic Host Control Protocol (DHCP). O PIX 7.x ou posterior e o Cisco Adaptive Security Device Manager (ASDM) não são executados em um PIX 501 ou 506. Consequentemente, para este exemplo, presume-se que o PIX remoto com DHCP e NAT é um PIX 501 ou 506 que executa o código do 6.x. Essa configuração permite que o PIX central aceite conexões IPSec dinâmicas. O PIX remoto usa o NAT para juntar-se aos dispositivos confidencialmente endereçados atrás dele à rede confidencialmente endereçada atrás do PIX central. O PIX remoto pode iniciar conexões ao PIX central (ele conhece o ponto de extremidade), mas o PIX central não pode iniciar conexões ao PIX remoto (ele não conhece o ponto de extremidade).

Nesse exemplo de configuração, Tiger é o PIX remoto, e Lion é o PIX central. Como o endereço IP do Tiger é desconhecido, você deve configurar o Lion para aceitar dinamicamente conexões de qualquer lugar, conhecendo a chave pré-compartilhada do curinga. O Tiger sabe qual tráfego deve ser criptografado (porque é especificado pela lista de acesso) e onde o endpoint Lion está localizado. O Tiger deve iniciar a conexão. Ambos os lados executam NAT e nat 0 para ignorar NAT para tráfego IPsec.

Além disso, o usuário remoto nessa configuração se conecta ao PIX central (Lion) usando o Cisco VPN Client 4.x. O usuário remoto não pode se conectar ao PIX remoto (Tigre), pois ambos os lados atribuíram endereços IP dinamicamente e não sabem para onde enviar a solicitação.

Consulte Configurando PIX para PIX Dynamic-to-Static IPsec com NAT e Cisco VPN Client para saber mais sobre o mesmo cenário no PIX 6.x com Cisco VPN Client 3.x.

Prerequisites

Requirements

Não existem requisitos específicos para este documento.

Componentes Utilizados

As informações neste documento são baseadas nestas versões de software e hardware:

  • Software Cisco PIX Firewall versão 7.x e posterior (PIX central)

  • Software Cisco PIX Firewall versão 6.3.4 (PIX remoto)

  • Cisco VPN Client versão 4.x

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Consulte as Convenções de Dicas Técnicas da Cisco para obter mais informações sobre convenções de documentos.

Configurar

Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.

Nota: Use a Command Lookup Tool (somente clientes registrados) para obter mais informações sobre os comandos usados nesta seção.

Diagrama de Rede

Este documento utiliza a seguinte configuração de rede:

pix-dyntostat-ipsec-nat.gif

Configurações

Este documento utiliza as seguintes configurações:

Leão 
PIX Version 7.0(0)  
names 
! 
interface Ethernet0 
 nameif outside 
 security-level 0 
 ip address 172.18.124.166 255.255.255.0  
! 
interface Ethernet1 
 nameif inside 
 security-level 100 
 ip address 10.2.2.1 255.255.255.0  
! 
interface Ethernet2 
 shutdown 
 nameif intf2 
 security-level 4 
 no ip address 
! 
interface Ethernet3 
 shutdown 
 nameif intf3 
 security-level 6 
 no ip address 
! 
interface Ethernet4 
 shutdown 
 nameif intf4 
 security-level 8 
 no ip address 
! 
interface Ethernet5 
 shutdown 
 nameif intf5 
 security-level 10 
 no ip address 
! 
enable password 8Ry2YjIyt7RRXU24 encrypted 
passwd 2KFQnbNIdI.2KYOU encrypted 
hostname lion 
domain-name cisco.com 
boot system flash:/image.bin 
ftp mode passive 
access-list 100 extended permit ip 10.2.2.0 255.255.255.0 10.1.1.0 255.255.255.0  
access-list 100 extended permit ip 10.2.2.0 255.255.255.0 10.3.3.0 255.255.255.0  
pager lines 24 
mtu outside 1500 
mtu inside 1500 
mtu intf2 1500 
mtu intf3 1500 
mtu intf4 1500 
mtu intf5 1500 
ip local pool clientpool 10.3.3.1-10.3.3.10 
no failover 
monitor-interface outside 
monitor-interface inside 
monitor-interface intf2 
monitor-interface intf3 
monitor-interface intf4 
monitor-interface intf5 
asdm image flash:/asdm-501.bin 
asdm history enable 
arp timeout 14400 
nat-control 
global (outside) 1 interface 
nat (inside) 0 access-list 100 
nat (inside) 1 0.0.0.0 0.0.0.0 
route outside 0.0.0.0 0.0.0.0 172.18.124.1 1 
timeout xlate 3:00:00 
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 
timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00 
timeout uauth 0:05:00 absolute 
aaa-server TACACS+ protocol tacacs+ 
aaa-server RADIUS protocol radius 
group-policy unityclient internal 
group-policy unityclient attributes 
 wins-server value 10.1.1.3 
 dns-server value 10.1.1.3 
 vpn-idle-timeout 30 
 default-domain value cisco.com 
 user-authentication disable 
username cisco password 3USUcOPFUiMCO4Jk encrypted 
http server enable 
http 0.0.0.0 0.0.0.0 outside 
http 0.0.0.0 0.0.0.0 inside 
no snmp-server location 
no snmp-server contact 
snmp-server community public 
snmp-server enable traps snmp 
crypto ipsec transform-set myset esp-des esp-md5-hmac  
crypto dynamic-map cisco 1 set transform-set myset 
crypto map dyn-map 20 ipsec-isakmp dynamic cisco 
crypto map dyn-map interface outside 
isakmp enable outside 
isakmp policy 20 authentication pre-share 
isakmp policy 20 encryption des 
isakmp policy 20 hash md5 
isakmp policy 20 group 2 
isakmp policy 20 lifetime 3600 
isakmp policy 65535 authentication pre-share 
isakmp policy 65535 encryption 3des 
isakmp policy 65535 hash sha 
isakmp policy 65535 group 2 
isakmp policy 65535 lifetime 86400 
telnet timeout 5 
ssh timeout 5 
ssh version 1 
console timeout 0 
tunnel-group DefaultL2LGroup type ipsec-l2l
tunnel-group DefaultL2LGroup general-attributes
   authentication-server-group none
tunnel-group DefaultL2LGroup ipsec-attributes
   pre-shared-key * 
tunnel-group unityclient type ipsec-ra 
tunnel-group unityclient general-attributes 
 address-pool clientpool 
 authentication-server-group none 
 default-group-policy unityclient 
tunnel-group unityclient ipsec-attributes 
 pre-shared-key * 
! 
class-map inspection_default 
 match default-inspection-traffic 
! 
! 
policy-map global_policy 
 class inspection_default 
  inspect dns maximum-length 512  
  inspect ftp  
  inspect h323 h225  
  inspect h323 ras  
  inspect http  
  inspect netbios  
  inspect rsh  
  inspect rtsp  
  inspect skinny  
  inspect esmtp  
  inspect sqlnet  
  inspect sunrpc  
  inspect tftp  
  inspect sip  
  inspect xdmcp  
!  
service-policy global_policy global 
Cryptochecksum:4e20a2153437d60c7f01054808d41b42 
: end

Tigre 
PIX Version 6.3(4) 
interface ethernet0 auto 
interface ethernet1 auto 
interface ethernet2 auto shutdown 
interface ethernet3 auto shutdown 
interface ethernet4 auto shutdown 
interface ethernet5 auto shutdown 
nameif ethernet0 outside security0 
nameif ethernet1 inside security100 
nameif ethernet2 intf2 security4 
nameif ethernet3 intf3 security6 
nameif ethernet4 intf4 security8 
nameif ethernet5 intf5 security10 
enable password 8Ry2YjIyt7RRXU24 encrypted 
passwd 2KFQnbNIdI.2KYOU encrypted 
hostname tiger 
domain-name cisco.com 
fixup protocol dns maximum-length 512 
fixup protocol ftp 21 
fixup protocol h323 h225 1720 
fixup protocol h323 ras 1718-1719 
fixup protocol http 80 
fixup protocol rsh 514 
fixup protocol rtsp 554 
fixup protocol sip 5060 
fixup protocol sip udp 5060 
fixup protocol skinny 2000 
fixup protocol smtp 25 
fixup protocol sqlnet 1521 
fixup protocol tftp 69 
names 
access-list 101 permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0  
pager lines 24 
mtu outside 1500 
mtu inside 1500 
mtu intf2 1500 
mtu intf3 1500 
mtu intf4 1500 
mtu intf5 1500

!--- This command configures the outside interface !--- as a DHCP client and it is assumed that the IP address !--- 172.18.124.167 is assigned by the DHCP server.

ip address outside dhcp 
ip address inside 10.1.1.1 255.255.255.0 
no ip address intf2 
no ip address intf3 
no ip address intf4 
no ip address intf5 
ip audit info action alarm 
ip audit attack action alarm 
no failover 
failover timeout 0:00:00 
failover poll 15 
no failover ip address outside 
no failover ip address inside 
no failover ip address intf2 
no failover ip address intf3 
no failover ip address intf4 
no failover ip address intf5 
pdm history enable 
arp timeout 14400 
nat (inside) 0 access-list 101 
route outside 0.0.0.0 0.0.0.0 172.18.124.1 1 
timeout xlate 3:00:00 
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 
timeout uauth 0:05:00 absolute 
aaa-server TACACS+ protocol tacacs+  
aaa-server TACACS+ max-failed-attempts 3  
aaa-server TACACS+ deadtime 10  
aaa-server RADIUS protocol radius  
aaa-server RADIUS max-failed-attempts 3  
aaa-server RADIUS deadtime 10  
aaa-server LOCAL protocol local  
no snmp-server location 
no snmp-server contact 
snmp-server community public 
no snmp-server enable traps 
floodguard enable 
sysopt connection permit-ipsec 
crypto ipsec transform-set myset esp-des esp-md5-hmac  
crypto map newmap 10 ipsec-isakmp 
crypto map newmap 10 match address 101 
crypto map newmap 10 set peer 172.18.124.166 
crypto map newmap 10 set transform-set myset 
crypto map newmap interface outside 
isakmp enable outside 
isakmp key ******** address 172.18.124.166 netmask 255.255.255.255  
isakmp policy 10 authentication pre-share 
isakmp policy 10 encryption des 
isakmp policy 10 hash md5 
isakmp policy 10 group 2 
isakmp policy 10 lifetime 3600 
telnet timeout 5 
ssh timeout 5 
console timeout 0 
terminal width 80 
Cryptochecksum:906331b1b1ca162ea53e951588efb070 
: end

Verificar

Use esta seção para confirmar se a sua configuração funciona corretamente.

A Output Interpreter Tool ( somente clientes registrados) (OIT) oferece suporte a determinados comandos show. Use a OIT para exibir uma análise da saída do comando show.

Observação: você deve executar os comandos clear no modo de configuração.

  • clear crypto ipsec sa — Redefine as associações IPsec após tentativas falhadas de negociar um túnel VPN.

  • clear crypto isakmp sa — Redefine as associações de segurança ISAKMP (Internet Security Association and Key Management Protocol) após tentativas de negociação de um túnel VPN com falha.

  • show crypto engine ipsec — Exibe as sessões criptografadas.

Troubleshoot

Chaves pré-compartilhadas idênticas

Se o túnel IPsec LAN a LAN (L2L) não estiver estabelecido, verifique se a chave pré-compartilhada para o DefaultRAGroup e a chave pré-compartilhada para o DefaultL2LGroup são iguais. Se for esse o caso, o PIX/ASA termina primeiro o túnel no DefaultRAGroup e o túnel L2L provavelmente falhará. Certifique-se de que as chaves pré-compartilhadas para os dois grupos de túnel padrão sejam diferentes.

Comandos para Troubleshooting

A Output Interpreter Tool ( somente clientes registrados) (OIT) oferece suporte a determinados comandos show. Use a OIT para exibir uma análise da saída do comando show.

Nota:Consulte Informações Importantes sobre Comandos de Depuração antes de usar comandos debug.

  • debug crypto ipsec —Usado para ver se um cliente negocia a parte IPsec da conexão VPN.

  • debug crypto isakmp [level] —Usado para ver se os peers negociam a parte ISAKMP da VPN.

Exemplos bons de saída de depuração

Estes são exemplos de uma boa saída do comando debug:

PIX Central (7.0.0) 

lion(config)# 2nd try, on central PIX from remote PIXApr 05 16:48:31 [IKEv1 DEBUG]:
 IP = 172.18.124.167, processing SA payload 
Apr 05 16:48:31 [IKEv1 DEBUG]: IP = 172.18.124.167, Oakley proposal is acceptable 
Apr 05 16:48:31 [IKEv1 DEBUG]: IP = 172.18.124.167, processing IKE SA 
Apr 05 16:48:31 [IKEv1 DEBUG]: IP = 172.18.124.167, IKE SA Proposal # 1, Transform
 # 1 acceptable  Matches global IKE entry # 3 
Apr 05 16:48:31 [IKEv1 DEBUG]: IP = 172.18.124.167, constructing ISA_SA for isakmp 
Apr 05 16:48:31 [IKEv1 DEBUG]: IP = 172.18.124.167, constructing Fragmentation VID
 + extended capabilities payload 
Apr 05 16:48:31 [IKEv1]: IP = 172.18.124.167, IKE DECODE SENDING Message (msgid=0)
 with payloads : HDR + SA (1) + VENDOR (13) + NONE (0) total length : 104 
Apr 05 16:48:32 [IKEv1]: IP = 172.18.124.167, IKE DECODE RECEIVED Message (msgid=0)
 with payloads : HDR + KE (4) + NONCE (10) + VENDOR (13) + VENDOR (13) +VENDOR (13)
 + VENDOR (13) + NONE (0) total length : 256 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, processing ke payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, processing ISA_KE 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, processing nonce payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, processing VID payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, Received xauth V6 VID 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, processing VID payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, Received DPD VID 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, processing VID payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, Received Cisco Unity client VID 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, processing VID payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, Processing IOS/PIX Vendor ID 
payload (version: 1.0.0, capabilities: 00000025) 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, constructing ke payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, constructing nonce payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, constructing Cisco Unity VID payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, constructing xauth V6 VID payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, Send IOS VID 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, Constructing ASA spoofing IOS
 Vendor ID payload (version: 1.0.0, capabilities: 20000001) 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, constructing VID payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, Send Altiga/Cisco VPN3000/Cisco
 ASA GW VID 
Apr 05 16:48:32 [IKEv1]: IP = 172.18.124.167, Connection landed on tunnel_group
 DefaultL2LGroup
Apr 05 16:48:32 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Generating keys for Responder... 
Apr 05 16:48:32 [IKEv1]: IP = 172.18.124.167, IKE DECODE SENDING Message
 (msgid=0) with payloads : HDR + KE (4) + NONCE (10) + VENDOR (13) + VENDOR (13)
 + VENDOR (13) + VENDOR (13) + NONE (0) total length : 256 
Apr 05 16:48:32 [IKEv1]: IP = 172.18.124.167, IKE DECODE RECEIVED Message (msg 
id=0) with payloads : HDR + ID (5) + HASH (8) + NONE (0) total length : 71 
Apr 05 16:48:32 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Processing ID 
Apr 05 16:48:32 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 processing hash 
Apr 05 16:48:32 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 computing hash 
Apr 05 16:48:32 [IKEv1]: IP = 172.18.124.167, Connection landed on tunnel_group
 DefaultL2LGroup 
Apr 05 16:48:32 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 constructing ID 
Apr 05 16:48:32 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 construct hash payload 
Apr 05 16:48:32 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 computing hash 
Apr 05 16:48:32 [IKEv1 DEBUG]: IP = 172.18.124.167, Constructing IOS keep
 alive payload: proposal=32767/32767 sec. 
Apr 05 16:48:32 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 constructing dpd vid payload 
Apr 05 16:48:32 [IKEv1]: IP = 172.18.124.167, IKE DECODE SENDING Message
 (msgid=0) with payloads : HDR + ID (5) + HASH (8) + IOS KEEPALIVE (14) 
+ VENDOR (13) + NONE (0) total length : 102 
Apr 05 16:48:33 [IKEv1]: IP = 172.18.124.167, IKE DECODE RECEIVED Message
 (msgid=ba80c56e) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0)
 total length : 76 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 processing hash 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Processing Notify payload 
Apr 05 16:48:33 [IKEv1]: Received unexpected event EV_ACTIVATE_NEW_SA in
 state MM_TM_INIT_MODECFG_H 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Delay Quick Mode processing, Cert/Trans Exch/RM DSID in progress 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Resume Quick Mode processing, Cert/Trans Exch/RM DSID completed 
Apr 05 16:48:33 [IKEv1]: Group = DefaultL2LGroup, IP = 172.18.124.167, PHASE 1COMPLETED 
Apr 05 16:48:33 [IKEv1]: IP = 172.18.124.167, Keep-alive type for this connection: DPD 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Starting phase 1 rekey timer: 3420000 (ms) 
Apr 05 16:48:33 [IKEv1]: IP = 172.18.124.167, IKE DECODE RECEIVED Message
 (msgid=20c2120e) with payloads : HDR + HASH (8) + SA (1) + NONCE (10) + ID
 (5) + ID (5) + NONE (0) total length : 164 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 processing hash 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 processing SA payload 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 processing nonce payload 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Processing ID 
Apr 05 16:48:33 [IKEv1]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Received remote IP Proxy Subnet data in ID Payload:   Address 10.1.1.0,
 Mask 255.255.255.0, Protocol 0, Port 0 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Processing ID 
Apr 05 16:48:33 [IKEv1]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Received local IP Proxy Subnet data in ID Payload:   Address 10.2.2.0,
 Mask 255.255.255.0, Protocol 0, Port 0 
Apr 05 16:48:33 [IKEv1]: QM IsRekeyed old sa not found by addr 
Apr 05 16:48:33 [IKEv1]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 IKE Remote Peer configured for SA: cisco 
Apr 05 16:48:33 [IKEv1]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 processing IPSEC SA 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 IPSec SA Proposal # 1, Transform # 1 acceptable  Matches global IPSec SA entry # 1 
Apr 05 16:48:33 [IKEv1]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 IKE: requesting SPI! 
Apr 05 16:48:33 [IKEv1 DEBUG]: IKE got SPI from key engine: SPI = 0xd5243861 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 oakley constucting quick mode 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 constructing blank hash 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 constructing ISA_SA for ipsec 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 constructing ipsec nonce payload 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 constructing proxy ID 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Transmitting Proxy Id: 
  Remote subnet: 10.1.1.0  Mask 255.255.255.0 Protocol 0  Port 0 
  Local subnet:  10.2.2.0  mask 255.255.255.0 Protocol 0  Port 0 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 constructing qm hash 
Apr 05 16:48:33 [IKEv1]: IP = 172.18.124.167, IKE DECODE SENDING Message
 (msgid=20c2120e) with payloads : HDR + HASH (8) + SA (1) + NONCE (10) +
 ID (5) + ID (5) + NONE (0) total length : 164 
Apr 05 16:48:33 [IKEv1]: IP = 172.18.124.167, IKE DECODE RECEIVED Message
 (msgid=20c2120e) with payloads : HDR + HASH (8) + NONE (0) total length : 48 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 processing hash 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 loading all IPSEC SAs 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Generating Quick Mode Key! 
Apr 05 16:48:33 [IKEv1 DEBUG]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Generating Quick Mode Key! 
Apr 05 16:48:33 [IKEv1]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 Security negotiation complete for User (DefaultL2LGroup)  Responder,
 Inbound SPI = 0xd5243861, Outbound SPI = 0x7bb11ead 
Apr 05 16:48:33 [IKEv1 DEBUG]: IKE got a KEY_ADD msg for SA: SPI = 0x7bb11ead 
Apr 05 16:48:33 [IKEv1 DEBUG]: pitcher: rcv KEY_UPDATE, spi 0xd5243861 
Apr 05 16:48:33 [IKEv1]: Group = DefaultL2LGroup, IP = 172.18.124.167,
 PHASE 2 COMPLETED (msgid=20c2120e)

NAT dinâmico de PIX remoto (6.3.4) 

tiger(config)# 
ISAKMP (0): beginning Main Mode exchange 

crypto_isakmp_process_block:src:172.18.124.166, dest:172.18.124.167 spt:500
 dpt:500 OAK_MM exchange 
ISAKMP (0): processing SA payload. message ID = 0 

ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy 
ISAKMP:      encryption DES-CBC 
ISAKMP:      hash MD5 
ISAKMP:      default group 2 
ISAKMP:      auth pre-share 
ISAKMP:      life type in seconds 
ISAKMP:      life duration (basic) of 3600 
ISAKMP (0): atts are acceptable. Next payload is 0 
ISAKMP (0): processing vendor id payload 

ISAKMP (0): SA is doing pre-shared key authentication using id type
 ID_FQDN return status is IKMP_NO_ERROR 
crypto_isakmp_process_block:src:172.18.124.166, dest:172.18.124.167
 spt:500 dpt:500 OAK_MM exchange 
ISAKMP (0): processing KE payload. message ID = 0 
ISAKMP (0): processing NONCE payload. message ID = 0 
ISAKMP (0): processing vendor id payload 
ISAKMP (0): processing vendor id payload 
ISAKMP (0): received xauth v6 vendor id 
ISAKMP (0): processing vendor id payload 
ISAKMP (0): speaking to another IOS box! 
ISAKMP (0): processing vendor id payload 
ISAKMP (0): speaking to a VPN3000 concentrator 
ISAKMP (0): ID payload 
        next-payload : 8 
        type         : 2 
        protocol     : 17 
        port         : 500 
        length       : 19 
ISAKMP (0): Total payload length: 23 
return status is IKMP_NO_ERROR 
crypto_isakmp_process_block:src:172.18.124.166, dest:172.18.124.167 spt:500 dpt:500 
OAK_MM exchange 
ISAKMP (0): processing ID payload. message ID = 0 
ISAKMP (0): processing HASH payload. message ID = 0 
ISAKMP (0): processing vendor id payload 

ISAKMP (0): remote peer supports dead peer detection 

ISAKMP (0): SA has been authenticated 

ISAKMP (0): beginning Quick Mode exchange, M-ID of 549589518:20c2120eIPSEC(key_engine):
 got a queue event... 
IPSEC(spi_response): getting spi 0x7bb11ead(2075205293) for SA 
        from  172.18.124.166 to  172.18.124.167 for prot 3 

return status is IKMP_NO_ERROR 
ISAKMP (0): sending INITIAL_CONTACT notify 
ISAKMP (0): sending NOTIFY message 24578 protocol 1 
VPN Peer: ISAKMP: Added new peer: ip:172.18.124.166/500 Total VPN Peers:1 
VPN Peer: ISAKMP: Peer ip:172.18.124.166/500 Ref cnt incremented to:1 Total VPN Peers:1 
crypto_isakmp_process_block:src:172.18.124.166, dest:172.18.124.167 spt:500 dpt:500 
OAK_QM exchange 
oakley_process_quick_mode: 
OAK_QM_IDLE 
ISAKMP (0): processing SA payload. message ID = 549589518 

ISAKMP : Checking IPSec proposal 1 

ISAKMP: transform 1, ESP_DES 
ISAKMP:   attributes in transform: 
ISAKMP:      SA life type in seconds 
ISAKMP:      SA life duration (basic) of 28800 
ISAKMP:      SA life type in kilobytes 
ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0 
ISAKMP:      encaps is 1 
ISAKMP:      authenticator is HMAC-MD5 
ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): proposal part #1, 
  (key eng. msg.) dest= 172.18.124.166, src= 172.18.124.167, 
    dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), 
    src_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
    protocol= ESP, transform= esp-des esp-md5-hmac , 
    lifedur= 0s and 0kb, 
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4 

ISAKMP (0): processing NONCE payload. message ID = 549589518 

ISAKMP (0): processing ID payload. message ID = 549589518 
ISAKMP (0): processing ID payload. message ID = 549589518 
ISAKMP (0): Creating IPSec SAs 
        inbound SA from  172.18.124.166 to  172.18.124.167 (proxy 10.2.2.0 to 10.1.1.0) 
        has spi 2075205293 and conn_id 1 and flags 4 
        lifetime of 28800 seconds 
        lifetime of 4608000 kilobytes 
        outbound SA from  172.18.124.167 to  172.18.124.166 (proxy 10.1.1.0 to 10.2.2.0) 
        has spi 3575920737 and conn_id 2 and flags 4 
        lifetime of 28800 seconds 
        lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event... 
IPSEC(initialize_sas): , 
  (key eng. msg.) dest= 172.18.124.167, src= 172.18.124.166, 
    dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
    src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), 
    protocol= ESP, transform= esp-des esp-md5-hmac , 
    lifedur= 28800s and 4608000kb, 
    spi= 0x7bb11ead(2075205293), conn_id= 1, keysize= 0, flags= 0x4IPSEC(initialize_sas): , 
  (key eng. msg.) src= 172.18.124.167, dest= 172.18.124.166, 
    src_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
    dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), 
    protocol= ESP, transform= esp-des esp-md5-hmac , 
    lifedur= 28800s and 4608000kb, 
    spi= 0xd5243861(3575920737), conn_id= 2, keysize= 0, flags= 0x4 

VPN Peer: IPSEC: Peer ip:172.18.124.166/500 Ref cnt incremented to:2 Total VPN Peers:1 
VPN Peer: IPSEC: Peer ip:172.18.124.166/500 Ref cnt incremented to:3 Total VPN Peers:1
 return status is IKMP_NO_ERROR

VPN Client 4.0.5 no Central PIX 7.0 

lion(config)# Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing SA payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing ke payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing ISA_KE 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing nonce payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, Processing ID 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, Received xauth V6 VID 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, Received DPD VID 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, Received NAT-Traversal ver02 VID 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, Received Fragmentation VID 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, IKE Peer included IKE fragmentation
 capability flags:  Main Mode:        True  Aggressive Mode:  False 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, processing VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: IP = 64.102.51.191, Received Cisco Unity client VID 
Apr 05 16:49:56 [IKEv1]: IP = 64.102.51.191, Connection landed on tunnel_group unityclient 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, processing IKE SA 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, IKE SA Proposal # 1,
 Transform # 14 acceptable  Matches global IKE entry # 3 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, constructing ISA_SA
 for isakmp 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, 
 constructing ke payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, 
 constructing nonce payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Generating keys for Responder... 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing ID 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 construct hash payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 computing hash 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing Cisco Unity VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing xauth V6 VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing dpd vid payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing Fragmentation VID + extended capabilities payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Send Altiga/Cisco VPN3000/Cisco ASA GW VID 
Apr 05 16:49:56 [IKEv1]: IP = 64.102.51.191, IKE DECODE SENDING Message
 (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + 
 HASH (8) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR
 (13) + NONE (0) total length : 378 
Apr 05 16:49:56 [IKEv1]: IP = 64.102.51.191, IKE DECODE RECEIVED Message
 (msgid=0) with payloads : HDR + HASH (8) + NOTIFY (11) + VENDOR (13) +
 VENDOR (13) + NONE (0) total length : 116 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, processing hash 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, computing hash 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Processing Notify payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 processing VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Processing IOS/PIX Vendor ID payload (version: 1.0.0, capabilities: 00000408) 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 processing VID payload 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Received Cisco Unity client VID 
Apr 05 16:49:56 [IKEv1]: IP = 64.102.51.191, IKE DECODE RECEIVED Message
 (msgid=a0bb428) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0)
 total length: 196 
Apr 05 16:49:56 [IKEv1 DEBUG]: process_attr(): Enter! 
Apr 05 16:49:56 [IKEv1 DEBUG]: Processing cfg Request attributes 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for IPV4 address! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for IPV4 net mask! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for DNS server address! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for WINS server address! 
Apr 05 16:49:56 [IKEv1]: Group = unityclient, IP = 64.102.51.191, Received
 unsupported transaction mode attribute: 5 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for Banner! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for Save PW setting! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for Default Domain Name! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for Split Tunnel List! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for Split DNS! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for PFS setting! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for backup ip-sec peer list! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for Application Version! 
Apr 05 16:49:56 [IKEv1]: Group = unityclient, IP = 64.102.51.191, Client Type: WinNT
  Client Application Version: 4.0.5 (Rel) 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for FWTYPE! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for DHCP hostname
 for DDNS is: tthotus-xp! 
Apr 05 16:49:56 [IKEv1 DEBUG]: MODE_CFG: Received request for UDP Port! 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing blank hash 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing qm hash 
Apr 05 16:49:56 [IKEv1]: IP = 64.102.51.191, IKE DECODE SENDING Message
 (msgid=a0bb428) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0)
 total length : 157 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Delay Quick Mode processing, Cert/Trans Exch/RM DSID in progress 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Resume Quick Mode processing, Cert/Trans Exch/RM DSID completed 
Apr 05 16:49:56 [IKEv1]: Group = unityclient, IP = 64.102.51.191, PHASE 1 COMPLETED 
Apr 05 16:49:56 [IKEv1]: IP = 64.102.51.191, Keep-alive type for this connection: DPD 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Starting phase 1 rekey timer: 3420000 (ms) 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 sending notify message 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing blank hash 
Apr 05 16:49:56 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing qm hash 
Apr 05 16:49:56 [IKEv1]: IP = 64.102.51.191, IKE DECODE SENDING Message
 (msgid=9be7674c) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE
 (0) total length : 84 
Apr 05 16:49:57 [IKEv1]: IP = 64.102.51.191, IKE DECODE RECEIVED Message
 (msgid=833e7945) with payloads : HDR + HASH (8) + SA (1) + NONCE (10)
 + ID (5) + ID (5) + NONE (0) total length : 1022 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, processing hash 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 processing SA payload 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 processing nonce payload 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, Processing ID 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191,
 Received remote Proxy Host data in ID Payload:  Address 10.3.3.1, Protocol 0, Port 0 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, Processing ID 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191,
 Received local IP Proxy Subnet data in ID Payload:   Address 0.0.0.0,
 Mask 0.0.0.0, Protocol 0, Port 0 
Apr 05 16:49:57 [IKEv1]: QM IsRekeyed old sa not found by addr 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191,
 IKE Remote Peer configured for SA: cisco 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191,
 processing IPSEC SA 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 IPSecSA Proposal # 14, Transform # 1 acceptable  Matches global IPSec SA entry # 1 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191, IKE: requesting SPI! 
Apr 05 16:49:57 [IKEv1 DEBUG]: IKE got SPI from key engine: SPI = 0x05953824 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 oakley constucting quick mode 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing blank hash 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing ISA_SA for ipsec 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191, 
 Overriding Initiator's IPSec rekeying duration from 2147483 to 28800 seconds 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing ipsec nonce payload 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing proxy ID 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Transmitting Proxy Id: 
  Remote host: 10.3.3.1  Protocol 0  Port 0 
  Local subnet:  0.0.0.0  mask 0.0.0.0 Protocol 0  Port 0 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Sending RESPONDER LIFETIME notification to Initiator 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing qm hash 
Apr 05 16:49:57 [IKEv1]: IP = 64.102.51.191, IKE DECODE SENDING Message
 (msgid=833e7945) with payloads : HDR + HASH (8) + SA (1) + NONCE (10)
 + ID (5) + ID (5) + NOTIFY (11) + NONE (0) total length : 176 
Apr 05 16:49:57 [IKEv1]: IP = 64.102.51.191, IKE DECODE RECEIVED Message
 (msgid=833e7945) with payloads : HDR + HASH (8) + NONE (0) total length : 48 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 processing hash 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 loading all IPSEC SAs 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Generating Quick Mode Key! 
Apr 05 16:49:57 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Generating Quick Mode Key! 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191,
 Security negotiation complete for User (unityclient)  Responder,
 Inbound SPI = 0x05953824, Outbound SPI = 0xd08c6486 
Apr 05 16:49:57 [IKEv1 DEBUG]: IKE got a KEY_ADD msg for SA: SPI = 0xd08c6486 
Apr 05 16:49:57 [IKEv1 DEBUG]: pitcher: rcv KEY_UPDATE, spi 0x5953824 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191,
 Adding static route for client address: 10.3.3.1 
Apr 05 16:49:57 [IKEv1]: Group = unityclient, IP = 64.102.51.191, PHASE 2 COMP 
LETED (msgid=833e7945) 
Apr 05 16:50:07 [IKEv1]: IP = 64.102.51.191, IKE DECODE RECEIVED Message
 (msgid=403ee701) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE
 (0) total length : 80 
Apr 05 16:50:07 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 processing hash 
Apr 05 16:50:07 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Processing Notify payload 
Apr 05 16:50:07 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Received keep-alive of type DPD R-U-THERE (seq number 0x4b55b6e4) 
Apr 05 16:50:07 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0x4b55b6e4) 
Apr 05 16:50:07 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing blank hash 
Apr 05 16:50:07 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing qm hash 
Apr 05 16:50:07 [IKEv1]: IP = 64.102.51.191, IKE DECODE SENDING Message
 (msgid=78998a29) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE
 (0) total length : 80 
Apr 05 16:50:17 [IKEv1]: IP = 64.102.51.191, IKE DECODE RECEIVED Message
 (msgid=dba719e9) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0)
 total length : 80 
Apr 05 16:50:17 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191, processing hash 
Apr 05 16:50:17 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Processing Notify payload 
Apr 05 16:50:17 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Received keep-alive of type DPD R-U-THERE (seq number 0x4b55b6e5) 
Apr 05 16:50:17 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0x4b55b6e5) 
Apr 05 16:50:17 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing blank hash 
Apr 05 16:50:17 [IKEv1 DEBUG]: Group = unityclient, IP = 64.102.51.191,
 constructing qm hash 
Apr 05 16:50:17 [IKEv1]: IP = 64.102.51.191, IKE DECODE SENDING Message
 (msgid=40456779) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE
 (0) total length : 80

Informações Relacionadas

Histórico de revisões

Revisão Data de publicação Comentários
1.0
03-May-2007
Versão inicial

Este documento lhe foi útil?

FeedbackFeedback

Contate a Cisco

Este documento se refere a estes produtos