Substituição do switch spine Nexus 9236C - CPAR
Contents
Introduction
Este documento descreve as etapas necessárias para substituir um switch spine com falha (Nexus 9236C) em uma configuração Ultra-M.
Este procedimento se aplica a um ambiente Openstack por meio da versão NEWTON, onde o ESC não gerencia o Cisco Prime Access Registrar (CPAR) e o CPAR é instalado diretamente na VM implantada no Openstack.
Informações de Apoio
O Ultra-M é uma solução de núcleo de pacotes móveis virtualizados, pré-embalada e validada, projetada para simplificar a implantação de VNFs. Os servidores que fazem parte da configuração Ultra-M estão conectados a três tipos diferentes de switches:
- Catalyst Switch
- Switch Folha
- Switch spine
Esta imagem mostra a topologia de rede de uma configuração Ultra-M:
Este documento destina-se ao pessoal da Cisco que conhece a configuração do Cisco Ultra-M e as operações do Switch Catalyst.
Abreviaturas
| VNF | Função de rede virtual |
| SPINE | Switch Nexus 9236C como spine |
| MOP | Método de Procedimento |
| LAN | Rede local |
| FTP | Protocolo de transferência de arquivo |
| TFTP | Protocolo trivial file transfer |
| CIMC | Controlador de gerenciamento integrado da Cisco |
Fluxo de trabalho do MoP
Esta imagem mostra o fluxo de trabalho de alto nível do Procedimento de substituição.
Switch spine na configuração UltraM
Pré-requisito
Faça um backup do arquivo de configuração do switch Spine por FTP/TFTP antes que ele continue com a substituição do switch.
AL03-N9236c-POD2-spine1# copy running-config sftp:
Enter destination filename: [AL03-N9236c-POD2-spine1-running-config] backup-spine-cfg-2
Enter vrf (If no input, current vrf 'default' is considered): management
Enter hostname for the sftp server: 10.1.1.1
Enter username: root
The authenticity of host '10.1.1.1 (10.1.1.1)' can't be established.
ECDSA key fingerprint is SHA256:dnHSXQ6fyYX5v8DU87oqVkCoA8CSPW7CpT+o2qilNI4.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added '10.1.1.1' (ECDSA) to the list of known hosts.
root@10.1.1.1's password:
Connected to 10.1.1.1.
sftp> put /var/tmp/vsh/backup-spine-cfg-2 backup-spine-cfg-2
Uploading /var/tmp/vsh/backup-spine-cfg-2 to /root/backup-spine-cfg-2
/var/tmp/vsh/backup-spine-cfg-2 0% 0 0.0KB/s --:-- ETA /var/tmp/vsh/backup-spine-cfg-2 100% 11KB 11.2KB/s 00:00
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.
Verificações de integridade
Etapa 1. Verifique a versão atual do software que é executado no switch e anote-a.
AL03-N9236c-POD2-spine1# show ver
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2018, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source. This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0 or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.
Software
BIOS: version 07.59
NXOS: version 7.0(3)I7(3)
BIOS compile time: 08/26/2016
NXOS image file is: bootflash:///nxos.7.0.3.I7.3.bin
NXOS compile time: 2/12/2018 13:00:00 [02/12/2018 19:13:48]
Hardware
cisco Nexus9000 C9236C chassis
Intel(R) Xeon(R) CPU @ 1.80GHz with 16400560 kB of memory.
Processor Board ID FDO211613CA
Device name: AL03-N9236c-POD2-spine1
bootflash: 53298520 kB
Kernel uptime is 134 day(s), 14 hour(s), 48 minute(s), 25 second(s)
Last reset at 705173 usecs after Fri Mar 2 17:56:31 2018
Reason: Reset due to upgrade
System version: 7.0(3)I5(2)
Service:
plugin
--More-- Core Plugin, Ethernet Plugin
Active Package(s):
Etapa 2. Verifique o uso da licença atual.
AL03-N9236c-POD2-spine1# show license uasgesage
Feature Ins Lic Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
N9K_LIC_1G No - Unused -
VPN_FABRIC No - Unused -
FCOE_NPV_PKG No - Unused -
SECURITY_PKG No 0 Unused -
N9K_UPG_EX_10G No - Unused -
TP_SERVICES_PKG No - Unused -
NXOS_ADVANTAGE_GF No - Unused -
NXOS_ADVANTAGE_M4 No - Unused -
NXOS_ADVANTAGE_XF No - Unused -
NXOS_ESSENTIALS_GF No - Unused -
NXOS_ESSENTIALS_M4 No - Unused -
NXOS_ESSENTIALS_XF No - Unused -
SAN_ENTERPRISE_PKG No - Unused -
PORT_ACTIVATION_PKG No 0 Unused -
NETWORK_SERVICES_PKG No - Unused -
NXOS_ADVANTAGE_M8-16 No - Unused -
NXOS_ESSENTIALS_M8-16 No - Unused -
FC_PORT_ACTIVATION_PKG No 0 Unused -
LAN_ENTERPRISE_SERVICES_PKG Yes - In use Never -
--------------------------------------------------------------------------------
Etapa 3. Certifique-se de que os cabos físicos conectados ao canal da porta do switch, à Vlan e também ao status da porta estejam corretos como esperado.
AL03-N9236c-POD2-spine1# show interface status | grep connected
mgmt0 -- connected routed full 100 --
Eth1/1 Connected to leaf1 connected trunk full 100G QSFP-100G-AOC5M
Eth1/2 Connected to leaf1 connected trunk full 100G QSFP-100G-AOC5M
Eth1/4 Connected to leaf2 connected trunk full 100G QSFP-100G-AOC5M
Eth1/5 Connected to leaf2 connected trunk full 100G QSFP-100G-AOC5M
Eth1/7 Connected to Leaf3 connected trunk full 100G QSFP-100G-AOC5M
Eth1/8 Connected to Leaf3 connected trunk full 100G QSFP-100G-AOC5M
Eth1/10 connect leaf4 connected trunk full 100G QSFP-100G-AOC5M
Eth1/11 connect leaf4 connected trunk full 100G QSFP-100G-AOC5M
Eth1/21/1 Connected to NMNET connected 101 full 10G QSFP-40G-SR4
Eth1/29 Connected to AL04- connected trunk full 100G QSFP-100G-AOC5M
Eth1/30 Connected to AL04- connected trunk full 100G QSFP-100G-AOC5M
Eth1/36/1 connected to ARG | connected routed full 10G QSFP-40G-SR4
Eth1/36/2 connected to ARG | disabled routed auto auto QSFP-40G-SR4
Eth1/36/3 connected to ARG | disabled routed auto auto QSFP-40G-SR4
Eth1/36/4 connected to ARG | disabled routed auto auto QSFP-40G-SR4
Po10 -- connected routed full 10G --
Po10.3101 -- connected routed full 10G --
Po10.3109 -- connected routed full 10G --
Po18 -- connected trunk full 100G --
Po21 -- connected trunk full 100G --
Po22 -- connected trunk full 100G --
Po25 -- connected trunk full 100G --
Po26 -- connected trunk full 100G --
Lo1 -- connected routed auto auto --
Vlan101 -- connected routed auto auto --
Vlan1025 vPCRF 1 and vPCRF connected routed auto auto --
Vlan1026 Replication for vP connected routed auto auto --
Vlan1031 External Traffic v connected routed auto auto --
Vlan1032 External External connected routed auto auto --
Vlan1033 External Traffic connected routed auto auto --
Vlan1034 External Traffic v connected routed auto auto --
Vlan1035 External Traffic v connected routed auto auto --
Vlan1036 External Traffic v connected routed auto auto --
Vlan1041 External Traffic A connected routed auto auto --
Vlan1042 External Traffic A connected routed auto auto --
Vlan1043 External Traffic A connected routed auto auto --
Vlan2601 Global Interchassi connected routed auto auto --
Vlan2602 NMNET Interchassis connected routed auto auto --
Etapa 4. Verifique se os vizinhos BGP estão ativados.
AL03-N9236c-POD2-spine1# show ip bgp summary vrf all
BGP summary information for VRF NMNET, address family IPv4 Unicast
BGP router identifier 10.225.247.201, local AS number 65361
BGP table version is 2, IPv4 Unicast config peers 2, capable peers 1
0 network entries and 0 paths using 0 bytes of memory
BGP attribute entries [0/0], BGP AS path entries [0/0]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.100.6 4 65361 193834 193833 2 0 0 19w1d 0
10.250.180.185 4 65137 0 0 0 0 0 19w1d Idle
BGP summary information for VRF default, address family IPv4 Unicast
BGP router identifier 10.0.200.1, local AS number 65361
BGP table version is 161, IPv4 Unicast config peers 2, capable peers 2
18 network entries and 29 paths using 5700 bytes of memory
BGP attribute entries [3/480], BGP AS path entries [1/6]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.100.2 4 65361 3868481 3868419 161 0 0 19w1d 12
10.163.140.225 4 65137 3868521 3868365 161 0 0 19w1d 5
AL03-N9236c-POD2-spine1# show ipv6 bgp summary vrf all
Etapa 5. Verifique se o estado dos vizinhos BFD está ativo.
AL03-N9236c-POD2-spine1# show bfd neighbors vrf all
OurAddr NeighAddr LD/RD RH/RS Holdown(mult) State Int Vrf
10.163.140.226 10.163.140.225 1090519042/1090519042 Up 107(3) Up Po10.3101 default
AL03-N9236c-POD2-spine1# show bfd ipv6 neighbor vrf all
Procedimento de substituição de switch
Etapa 1. Instale o novo switch no rack e conecte os cabos ao switch conforme observado. As etapas para a instalação do switch podem ser encontradas neste link: Guia de instalação de hardware do switch do modo Spine Nexus 236C NX-OS
Etapa 2. Verifique a versão do software do switch Nexus Spine e atualize/rebaixe para a versão do software conforme o link especificado: Guia de upgrade e downgrade do software Cisco Nexus 9000 Series NX-OS, versão 7.x
Etapa 3. Transfira o backup de configuração para o novo switch e copie essa configuração para a configuração de inicialização.
server-backup$ sftp admin@10.1.1.1
The authenticity of host '10.1.1.1 (10.1.1.1)' can't be established.
RSA key fingerprint is SHA256:fnbUmd2mL5yE94zxrRoKAlvYfQbheXJfQox7m3XfpIU.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added '10.1.1.1' (RSA) to the list of known hosts.
User Access Verification
Password:
Password:
Connected to 10.1.1.1.
sftp> ls
20170607_193430_poap_15489_1.log 20170607_193430_poap_15489_2.log 20170607_193430_poap_15489_init.log backup-spine-cfg-2 backup-spine.cfg
backup_run_02152018 bios_daemon.dbg cfg-july25th cfg-july25th-spine1 flash:
flash:cfg-aug8th-ybattina-afterNSO flash:cfg-jul28th home l3-cfg-aug10th license_FDO211406K1_16.lic
lost+found nxos.7.0.3.I4.4.bin nxos.7.0.3.I5.2.bin nxos.7.0.3.I7.3.bin platform-sdk.cmd
scripts spine-config-bkp starat virtual-instance vlan.dat 100% 33KB 21.7KB/s 00:01
sftp> put backup-spine-cfg-2
Uploading backup-spine-cfg-2 to /backup-spine-cfg-2
backup-spine-cfg-2 100% 33KB 23.5KB/s 00:01
sftp> bye
AL03-N9236c-POD2-spine1# copy bootflash:///backup-spine-cfg-2 startup-config
Copy progress 100% 33KB
Copy complete, now saving to disk (please wait)...
Copy complete.
Etapa 4. Recarregue o switch após carregar a configuração de backup.
AL03-N9236c-POD2-spine1#reload
Verificação do switch spine substituído
Depois que o switch estiver disponível para acesso, execute as verificações de integridade por meio desses comandos no switch spine para verificar se o switch substituído está disponível no estado esperado.
AL03-N9236c-POD2-spine1# show port-channel summary
AL03-N9236c-POD2-spine1# show ip bgp summary vrf all
AL03-N9236c-POD2-spine1# show ipv6 bgp summary vrf all
AL03-N9236c-POD2-spine1# show bfd neighbor vrf all
AL03-N9236c-POD2-spine1# show bfd ipv6 neighbor vrf all
FeedbackContate a Cisco
- Abrir um caso de suporte
- (É necessário um Contrato de Serviço da Cisco)