DEVICE=A:\DOS\HIMEM.SYS
DEVICE=A:\DOS\EMM386.EXE X=D000-DFFF FRAME=NONE
DEVICEHIGH=A:\IBMDSS14.SYS
DEVICEHIGH=A:\IBMDOSCS.SYS
DEVICEHIGH=A:\DICRMU01.SYS /MA-D000-D7FF /SH=1 /IX=5,10,11,15
DEVICE=A:\NET\IFSHLP.SYS
DEVICE=A:\DOS\RAMDRIVE.SYS 2048 /e
DEVICE=A:\DOS\ANSI.SYS
DOS=HIGH,UMB
FILES=40
BUFFERS=30
LASTDRIVE=Z
SHELL=COMMAND.COM /e:512 /p

Les fichiers IBMDSS14.SYS, IBMDOSCS.SYS et DICRMU01.SYS sont des fichiers PCMCIA Card et Socket Services pour l'exemple d'ordinateur portable IBM modèle. Remplacer les fichiers appropriés par le fabricant de l'ordinateur portable, le cas échéant.

Personnalisez le fichier cscpkt.ini inclus en fonction des besoins individuels :

[CSCPKT]
        ;Initialization file for Infrastructure operating mode

        ; NOTE: The following are some keyword parameters that may
        ;be modified.  Any commented or omitted keyword parameter
        ;assumes the factory default.  For most situations the
        ;factory defaults will be appropriate.  In situations where
        ;the factory default needs to be modified, uncomment or add the
        ;keyword parameter line and set the appropriate keyword value.

        SSID="network_ssid"     ;Must match Access Point setting
        ;FragThreshold=2312     ;Packet size to start fragmenting
        ;RTSThreshold=2312      ;Packet size to start sending RTS/CTS
        ;DataRate1=0x02         ;(1)   Mbps supported data bit rate
        ;DataRate2=0x04         ;(2)   Mbps supported data bit rate
        ;DataRate3=0x0B         ;(5.5) Mbps supported data bit rate
        ;DataRate4=0x16         ;(11)  Mbps supported data bit rate
        ;RefreshInterval=10000  ;Inactivity time to check association
        ;PowerSaveMode="CAM"    ;Constant Awake Mode
        ;MaxPowerSave="OFF"     ;Maximum power save mode
        NodeName="CiscoPC"      ;Descriptive station name
        AuthType="WEPOPEN"      ;WEP with open authentication

        ;The adapter needs 32 16-bit I/O ports, and 1 non-sharable IRQ.
        ;The following lines should be uncommented and the appropriate
        ;values set in the following scenarios:
        ; 1) PCMCIA mode: Override the I/O port base and/or IRQ
        ;                 assigned by PCMCIA card services.
        ; 2) PCMCIA mode: PCMCIA card services is not being used.
        ; 3) ISA mode: Override the I/O port base and/or IRQ assigned
        ;              by Plug and Play.
        ; 4) ISA mode: Non-Plug and Play operation.
        
        ;PortBase=0x140
        ;IRQ=5

        ;If the PCMCIA interface is being used without PCMCIA card services,
        ;uncomment the following lines and set the appropriate values.

        Memory=0xD000
        Socket=0

        ;If the PCMCIA interface is not being used, set the appropriate
        ;value of "ISA" or "PCI".

        BusType="PCMCIA"

Démarrez l'ordinateur pour charger le fichier config.sys ci-dessus.

Émettez la commande suivante :

a:>wepdos -365 -tx1 12345678901234567890123456

setting key 1 to 12345678901234567890123456
setting transmit key index to 1

Émettez la commande suivante :

a:>cscpkt 0x65

Cisco Wireless Packet Driver , version 2.04
(c) Copyright 2000 Cisco System , Inc.
All rights Reserved
Card recognized as a radio in socket 00
Driver Resources --> IO ports 0400-043F IRQ :03
350 series Firmware 4.25.30
Mac Address 00:09:7c:31:87:32