Exemple de configuration de la formation en ligne du multiplexeur d'accès DSL Huawei MA5600
Contenu
Introduction
Ce document décrit les étapes de configuration minimale requises sur le multiplexeur d'accès DSL (Digital Subscriber Line Access Multiplexer) Huawei MA5600 afin de permettre à la ligne d'abonné numérique à très haut débit (VDSL) de se former sur l'équipement client Cisco (CPE).
Conditions préalables
Conditions requises
Cisco vous recommande de respecter ces exigences avant de tenter cette configuration :
- Câble étroitement connecté sur le port VDSL du CPE et sur le port approprié du panneau de brassage du DSLAM
- Le CPE et la carte de ligne DSLAM doivent être opérationnels
Components Used
Les informations de ce document sont basées sur un routeur Cisco 887VA qui agit comme un CPE et un multiplexeur DSLAM Huwei 5600. Cependant, ce document n'est pas limité à des versions de logiciels et de matériels spécifiques.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Fond
Ce document vise à aider les ingénieurs à configurer Cisco CPE et un multiplexeur d'accès DSL Huawei dans des environnements dos à dos/labo et à comprendre les profils de base de l'extrémité bureau central (CO) de la DSL.
Configuration
Complétez ces sections afin de configurer votre équipement :
- Configuration du profil de ligne
- Configuration du profil de canal
- Configuration du modèle de ligne (combinaison du profil de ligne et du profil de canal)
- Appliquer le modèle de ligne sur le port DSLAM respectif où CPE est connecté
Configuration du profil de ligne
- Vérifiez les profils de ligne déjà créés.
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 4 - Configurez le profil de ligne.
MA5600#config
MA5600(config)#vdsl line-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl line-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Transmission mode:
> 0: Custom
> 1: All (G992.1~5,T1.413,G993.2)
> 2: Full rate(G992.1/3/5,T1.413,G993.2)
> 3: G.DMT (G992.1/3/5,G993.2)
> 4: G.HS (G992.1~5,G993.2)
> 5: ADSL (G.992.1~5,T1.413)
> 6: VDSL (G993.2)
> Please select (0~6) [1]:6 >>>>>>>>>>>>>>>>>> Selecting Transmission Mode as VDSL
> Bit swap downstream 1-disable 2-enable (1~2) [2]:1
> Bit swap upstream 1-disable 2-enable (1~2) [2]:1
> Please select the form of transmit rate adaptation downstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Please select the form of transmit rate adaptation upstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Will you set SNR margin parameters? (y/n) [n]:
> Will you set DPBO parameters? (y/n)[n]:
> Will you set UPBO parameters? (y/n)[n]:
> Will you set RFI notch configuration parameter? (y/n) [n]:
> Will you set VDSL tone blackout configuration parameter? (y/n) [n]:
> Will you set mode-specific parameters? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
Configuration du profil de canal
- Vérifiez les profils de canal déjà créés.
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 2 - Configurez le profil de canal.
MA5600(config)#vdsl channel-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl channel-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Data path mode 1-ATM, 2-PTM, 3-Both (1~3) [3]:2 >>>>>>>>>>>>>>>>>>>>>> PTM Mode
> Will you set the minimum impulse noise protection? (y/n) [n]:
> Will you set interleaving delay parameters? (y/n) [n]:
> Will you set parameters for rate? (y/n) [n]:
> Will you set rate thresholds? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------>
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
Configuration du modèle de ligne
- Vérifiez les modèles de ligne déjà créés.
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
------------------------------------------------------------------------------
Total: 5 - Configurez le modèle de ligne.
MA5600(config)#vdsl line-template add 61
Start adding template
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the template (y/n) [n]:y
> Please input template name:ZONE_TEST
> Please set the line-profile index (1~128) [1]:61 >>>>>>>>>>>>>>>>Line Profile
we added above
> Will you set channel configuration parameters? (y/n) [n]:y
> Please set the channel number (1~2) [1]:
> Channel1 configuration parameters:
> Please set the channel-profile index (1~128) [1]:61 >>>>>> Channel Profile
we added above
Add template 61 successfully
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
Appliquer le modèle de ligne au port DSLAM
Dans ce cas, le CPE était connecté au port 0 du logement 5 du multiplexeur DSLAM Huawei.
MA5600(config)#display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1
-------------------------------------------------------------------------
0 H563ADGE Failed
1 H565ADBF Normal >>>>>>>>>ADBF - Here 'A' means that this card supports ADSL
2 ADG Failed
3 H569SHEB Failed
4
5 H565VDBD Normal >>>> >>>>VDBD - Here 'V' means that this card supports VDSL
6
7 H561SCU Standby_normal O2FM >>>>>>>>>>>>>>>>>>>>>> Processor Cards
8 H561SCU Active_normal O2GS O2GS >>>>>>>>>>>>> Processor Cards
9
10
11 H565VDBD Failed
12 H569SHEB Failed
13
14 H561SHEA Failed
15
-------------------------------------------------------------------------
MA5600(config)#interface vdsl 0/5 (Board/ slot)
Check the port status: Status is deactivated and currently assigned to
Line Template 1 (default)
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Deactivated Disable 1 1
-----------------------------------------------------------------
Attribuer le modèle de ligne (61) au port (0/5/0)
MA5600(config-if-vdsl-0/5)#activate 0 template-index 61
>>>>>>>> We are already in board 0 slot 5, hence need to activate port 0 with
Line Template 61
MA5600(config-if-vdsl-0/5)#display port state 0
---------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activating Disable 61 1 >>>>>Check the status
---------------------------------------------------------------
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activated Disable 61 1 >>Status is activated
---------------------------------------------------------------
Vérification
Utilisez cette section afin de vérifier votre configuration.
L'Outil d'interprétation de sortie (clients enregistrés seulement) prend en charge certaines commandes d'affichage. Utilisez l'Outil d'interprétation de sortie afin de visualiser une analyse de commande d'affichage de sortie .
Vérification sur DSLAM
Vérifier les profils de ligne créés
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
Vérifier les profils de canaux créés
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
Vérifier les modèles de ligne créés
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
Vérifier l'état du port DSLAM
Pour cela, vous devez être en mode de configuration d’interface du multiplexeur DSLAM.
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Activated Disable 61 1
-----------------------------------------------------------------
Vérification sur CPE
Entrez la commande show controller vdsl 0 sur le CPE afin de vérifier l'état du contrôleur.
/snip
C887VA-M#show controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0x939B
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FTX162580HZ 887VA-M 15.2(4)M
Serial Number Far:
Modem Version Near: 15.2(4)M
Modem Version Far: 0x939b
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 12a
TC Mode: PTM
Dépannage
Il n'existe actuellement aucune information de dépannage spécifique pour cette configuration.
Informations connexes
Historique de révision
| Révision | Date de publication | Commentaires |
|---|---|---|
1.0 |
01-Dec-2014 |
Première publication |
CommentairesContacter Cisco
- Ouvrir un dossier d’assistance
- (Un contrat de service de Cisco est requis)