Release Notes for Cisco Aironet 350 and CB20A Client Adapter Install Wizard 1.4 for Windows

Table Of Contents

Release Notes for Cisco Aironet 350 and CB20A Client Adapter Install Wizard 1.4 for Windows

Contents

Introduction

System Requirements

Important Notes

Customized Installation Images (Notice to IT Professionals)

Firmware Is Upgraded Automatically

Reboot Required When Uninstalling ACU

Uninstalling Software Components

Inserting and Removing Client Adapters

New EAP-SIM Supplicant Available

Windows Wireless Network Connection Icon Shows Unavailable Connection (Windows XP Only)

Cisco Aironet Software Requires Completion of Encryption Authorization Form

Supporting Documentation

Installing or Upgrading Client Adapter Software

Finding Version Numbers

Finding the Install Wizard Version

Finding the Firmware and Driver Versions

Finding the ACU Version

Finding the ACM Version

Caveats

Open Caveats

Open Driver Caveats

Open ACU Caveats

Open ACM Caveats

Open Security Module Caveats

Other Open Caveats

Resolved Caveats

Resolved Install Wizard Caveats

Resolved Firmware Caveats

Resolved Driver Caveats

Resolved Security Module Caveats

Getting Bug Information on Cisco.com

Troubleshooting

Related Documentation

Obtaining Documentation

Cisco.com

Ordering Documentation

Documentation Feedback

Obtaining Technical Assistance

Cisco TAC Website

Opening a TAC Case

TAC Case Priority Definitions

Obtaining Additional Publications and Information

Release Notes for Cisco Aironet 350 and CB20A Client Adapter Install Wizard 1.4 for Windows

---

Contents

This document contains the following sections:

•Introduction

•System Requirements

•Important Notes

•Installing or Upgrading Client Adapter Software

•Finding Version Numbers

•Caveats

•Troubleshooting

•Related Documentation

•Obtaining Documentation

•Obtaining Technical Assistance

•Obtaining Additional Publications and Information

Introduction

This document describes system requirements, important notes, installation and upgrade procedures, and caveats for client adapter Install Wizard version 1.4 and the following software included in the Install Wizard file:

•Firmware version 5.41.00

•PC, LM, and PCI card driver version 8.5.26

•Mini PCI and PC-Cardbus card driver version 3.8.26

•Aironet Client Utility (ACU) version 6.3

•Aironet Client Monitor (ACM) version 2.3

•LEAP security module version 6.3.21

•EAP-FAST security module version 1.0

•PEAP security module version 1.2

•EAP-SIM security module version 1.0

---

Note Refer to the "New EAP-SIM Supplicant Available" section for information about a new EAP-SIM supplicant.

---

System Requirements

You need the following in order to install Install Wizard 1.4 and use its software components:

•One of the following Cisco Aironet client adapters:

–350 series PC, LM, PCI, or mini PCI card

–CB20A PC-Cardbus card

---

Note Install Wizard 1.4 and its software components are not supported for use with Cisco Aironet 340 series client adapters.

---

•A computer running the Windows 2000 or XP operating system

---

Note Install Wizard 1.4 and its software components are not supported for use with Windows 95, 98, 98 SE, NT, and Me.

---

---

Note All drivers and supporting software (Card and Socket Services) for the PC card slot or Cardbus slot must be loaded and configured.

---

•A display with a minimum resolution of 800 x 600 pixels

•35 MB of free hard disk space (minimum)

---

Note The Install Wizard terminates if you attempt to install it on a computer that has less than
35 MB of hard disk space.

---

•One of the following host supplicants if your wireless network uses host-based EAP authentication with WPA:

–Funk Odyssey Client supplicant version 2.2 (for Windows 2000)

–Windows XP Service Pack 1 and Microsoft supplicant Q815485 (for Windows XP)

---

Note Meetinghouse AEGIS Client supplicant version 2.1 or later is also supported for use with Windows 2000 and XP; however, it was not tested with this client adapter software release.

---

•The Microsoft 802.1X supplicant, if your wireless network uses EAP-TLS, PEAP, or EAP-SIM authentication

•If your wireless network uses PEAP authentication with a One-Time Password (OTP) user database:

–SofToken version 1.3, 2.0, or later from Secure Computing; SecurID version 2.5 from RSA; or hardware token from OTP vendors

–Your software token PIN or hardware token password

•If your wireless network uses EAP-SIM authentication:

–PCSC-compliant smartcard reader installed in your computer's Type II or Type III PC card slot

–Gemplus SIM+ smartcard inserted in the reader

–The SIM card's PIN

---

Note The EAP-SIM supplicant included in the Install Wizard file supports only Gemplus SIM+ cards; however, an updated supplicant is available that supports standard GSM-SIM cards as well as more recent versions of the EAP-SIM protocol. The new supplicant is available for download from Cisco.com at the following URL:

http://www.cisco.com/cgi-bin/tablebuild.pl/access-registrar-encrypted

---

•The following information from your system administrator:

–The logical name for your workstation (also referred to as client name)

–The protocols necessary to bind to the client adapter

–The case-sensitive service set identifier (SSID) for your RF network

–If your computer is not connected to a DHCP server, the IP address, subnet mask, and default gateway address of your computer

–The wired equivalent privacy (WEP) keys of the access points with which your client adapter will communicate, if your wireless network uses static WEP for security

–The username and password for your network account

–Protected access credentials (PAC) file if your wireless network uses EAP-FAST authentication with manual PAC provisioning

•Access points to which your client adapter may attempt to authenticate must use the following firmware versions or later: 12.00T (340, 350, and 1200 series access points) or Cisco IOS Release 12.2(4)JA (1100 series access points).

---

Note To use WPA or fast roaming, access points must use Cisco IOS Release 12.2(11)JA or later. To use radio management (RM), access points must use Cisco IOS Release 12.2(13)JA or later.

---

•All necessary infrastructure devices such as access points, servers, gateways, and user databases must be properly configured for any authentication type you plan to enable on the client.

Important Notes

Customized Installation Images (Notice to IT Professionals)

---

Caution Use caution when bundling the client adapter software into a customized installation image. If the registry settings are modified, the software may not install and uninstall properly.

---

Firmware Is Upgraded Automatically

The Install Wizard automatically upgrades the client adapter firmware to the version included in the Install Wizard file.

---

Note Applications such as AirMagnet and Wild Packets may fail after the firmware is upgraded. To resolve this problem, use ACU to downgrade the firmware to the previous version. Older versions of client adapter firmware are available from the Software Center on Cisco.com.

---

Reboot Required When Uninstalling ACU

---

Caution When you uninstall ACU, make sure you reboot your computer when prompted. Otherwise, the system may be rendered unable to boot, displaying the message "The Logon User Interface DLL cswGina.dll failed to load. Contact your system administrator to replace the DLL or restore the original DLL."

---

Uninstalling Software Components

All profiles are deleted if you use the Uninstall All Components option on the Cisco Aironet Wireless LAN Client Adapter Installation Wizard screen to uninstall the client adapter software. Cisco recommends that you use the Profile Manager's export feature to save your profiles before uninstalling the software.

Inserting and Removing Client Adapters

The following rules apply when inserting and removing client adapters:

•If you start ACU while a client adapter of one radio type is inserted (such as a 350 series PC card) and then eject the card and replace it with a card of another radio type (such as a CB20A PC-Cardbus card), ACU displays "Your Wireless LAN Adapter is not inserted" until ACU is shut down and restarted.

•The profiles for PC-Cardbus cards are tied to the slot in which the card is inserted. Therefore, you must always insert your PC-Cardbus card into the same slot, create profiles for both slots, or export the profiles for one slot and import them for the other slot.

New EAP-SIM Supplicant Available

A new EAP-SIM supplicant is available for download from Cisco.com. This new supplicant is an upgrade to the one included in the Install Wizard file. It provides new features, supports more recent versions of the EAP-SIM draft standard, and can be used with standard GSM-SIM cards as well as Gemplus SIM+ smartcards.

The new supplicant overwrites any previous EAP-SIM supplicant settings. If you plan to install the Cisco Aironet Install Wizard file after the new supplicant is installed, either perform an express installation or make sure that the EAP-SIM option is not selected on the Custom Installation screen. Otherwise, the EAP-SIM supplicant included in the Install Wizard file overwrites the new supplicant's settings.

You can access the latest EAP-SIM supplicant at the following URL:

http://www.cisco.com/cgi-bin/tablebuild.pl/access-registrar-encrypted

Windows Wireless Network Connection Icon Shows Unavailable Connection (Windows XP Only)

If your computer is running Windows XP and you configured your client adapter using ACU, the Windows Wireless Network Connection icon in the Windows system tray may be marked with a red X and show an unavailable connection even though a wireless connection exists. This condition is caused by a conflict between ACU and Windows XP's wireless network settings. Simply ignore the Windows icon and use the ACM icon to check the status of your client adapter's wireless connection.

Cisco Aironet Software Requires Completion of Encryption Authorization Form

In order to access Cisco Aironet software from the Software Center on Cisco.com, you must fill out a form to receive authorization to download encrypted software. Registered Cisco.com users are required to fill out the form only once, but public users must do so once each session, each time software is downloaded. A form is automatically created for public users. The form for registered Cisco.com users is at the following URL:

http://www.cisco.com/cgi-bin/Software/Crypto/crypto_main.pl

Supporting Documentation

The Cisco Aironet 340, 350, and CB20A Wireless LAN Client Adapters Installation and Configuration Guide for Windows (part number OL-1394-08) provides detailed installation, configuration, and troubleshooting information for Install Wizard 1.4 and its software components.

---

Note Install Wizard 1.4 and its software components are not supported for use with Cisco Aironet 340 series client adapters.

---

Installing or Upgrading Client Adapter Software

Follow these steps to use Install Wizard 1.4 to install or upgrade client adapter software on a computer running Windows 2000 or XP.

---

Note Install Wizard 1.4 and its software components are not supported for use with Windows 95, 98, 98 SE, NT, and Me.

---

---

Note You do not need to uninstall any previous versions of Cisco Aironet client adapter software (firmware, drivers, or utilities) or previous versions of the Install Wizard prior to installing Install Wizard 1.4.

---

---

Step 1 Use your computer's web browser to access the following URL:

http://www.cisco.com/public/sw-center/sw-wireless.shtml

Step 2 Choose Option #2: Aironet Wireless Software Display Tables.

---

Note You can download software from the Software Selector tool instead of the display tables. To do so, choose Option #1: Aironet Wireless Software Selector, follow the instructions on the screen, and go to Step 6.

---

Step 3 Click Cisco Aironet Wireless LAN Client Adapters.

Step 4 Under Aironet Client Adapter Installation Wizard (For Windows), click 802.11a/b (CB20A, 350 Series, 340 Series).

Step 5 Click the Install Wizard 1.4 file.

Step 6 Complete the encryption authorization form; then read and accept the terms and conditions of the Software License Agreement.

Step 7 Click the file again to download it.

Step 8 Save the file to your computer's hard drive.

Step 9 Insert the client adapter into your computer if it is not already inserted.

---

Caution Do not eject your client adapter at any time during the installation process, including during the reboot.

---

Step 10 If a driver is not currently installed for your client adapter, the Found New Hardware Wizard screen appears. Click Cancel.

Step 11 Find the Install Wizard file using Windows Explorer, double-click it, and extract its files to a folder.

---

Note To extract the files, click Browse on the WinZip Self-Extractor screen, choose the folder in which you want the files to be placed, and click OK and Unzip. After the files are extracted, click OK to close the screen.

---

Step 12 Close Windows Explorer. The Cisco Aironet Wireless LAN Client Adapter Installation Wizard screen appears (see Figure 1).

Figure 1 Cisco Aironet Wireless LAN Client Adapter Installation Wizard Screen

Step 13 Choose one of the following options and click Next:

---

Note To ensure compatibility among software components, Cisco recommends that you perform an express installation. If you perform a custom installation, Cisco recommends that you install all components.

---

•Express Installation/Upgrade (recommended)—Silently installs the client adapter firmware, drivers, client utilities, and security modules using the default values listed in Table 1.

•Custom Installation/Upgrade—Enables you to specify which software components are installed and to change the default values of certain parameters.

Step 14 If a message appears indicating that you may be required to restart your computer at the end of the installation process, click OK.

---

Note If you click Cancel, the installation process terminates.

---

Step 15 If you chose an express installation, go to Step 17. If you chose a custom installation, the Custom Installation screen appears (see Figure 2).

Figure 2 Custom Installation Screen

Step 16 Follow these steps to make selections on this screen.

a. Make sure that a check mark appears beside every software component that you want to install. For every component that is checked, the Install Wizard installs its version of that component. Every component that is not checked remains as it currently is on your system.

---

Note Click the + sign beside the Security Modules option to reveal the available security components.

---

---

Note Some components are dependent on others. Therefore, when you select or deselect these components, the settings of other components may change. A dependency notice appears when this occurs.

---

b. Click the + sign beside each component to view additional parameters. The current value of each parameter appears in the Value field.

c. To change the value of any parameter, click its current value in the Value field. A screen appears that lets you change the existing value.

d. Enter or select a new value and click OK. Table 1 describes each component and its parameters and lists any default value.

Table 1 Software Components and Their Parameters 

Component or Parameter	Description
Firmware	Installs the firmware version included in the Install Wizard file. Default: Checked
Disable Firmware Checking	The Disable Firmware Checking parameter affects the firmware that is bundled with the driver, not the firmware that is included in the Install Wizard. It controls whether the driver (whenever it loads) installs the firmware with which it is bundled. Note The driver loads each time you insert a client adapter or reboot your computer. Options: Yes or No Default: Yes
	Disable Firmware Checking	Description
	Yes	Prevents the driver from installing the firmware with which it is bundled, enabling the client adapter to retain its current firmware version.
	No	Causes the driver to install the firmware with which it is bundled if that firmware is newer than the firmware that is currently installed in the client adapter.
	Note The Disable Firmware Checking parameter is functionally equivalent to the Automatically Load New Firmware When NDIS Driver Is Updated parameter on the ACU Preferences screen. The parameter that is set last is the one that governs how the driver behaves.
Drivers	Installs the driver version included in the Install Wizard file. Default: Checked
Set Quiet Mode?	Specifies whether the client becomes quiet (to passively scan or listen) when its associated access point is turned off. In quiet mode, the client generates radio frequency energy only in direct response to an access point transmission. When the access point is turned back on, it starts sending beacons, which the client hears and can now respond to. This parameter applies to individual cards rather than profiles. It can be set differently for different cards and remains in effect across ACU sessions and computer reboots. Options: Yes or No Default: No Note You can also change the quiet mode setting in ACU by choosing the Turn Quiet Mode On/Off option from the Commands drop-down menu.
Aironet Client Utility	Installs the ACU version included in the Install Wizard file. Default: Checked
Installation Path	Determines the path where the ACU software will be installed. You can change the default by entering a new path. Default: C:\Program Files\Cisco Systems\Aironet Client Utility
Program Folder	Determines the program folder where the ACU software will be installed. You can change the default by entering a new folder name. Default: Cisco Systems
Place Icon on Desktop	Causes the installation program to add an ACU icon to your computer's desktop to provide quick access to the utility. Options: Yes or No Default: Yes
Allow Non-Administrator Users to Save Settings to the Registry	Enables users without administrative rights to modify profiles in ACU and save them to the registry. Options: Yes or No Default: Yes
Aironet Client Monitor	Installs the ACM version included in the Install Wizard file. Default: Checked
Installation Path	Determines the path where the ACM software will be installed. You can change the default by entering a new path. Default: C:\Program Files\Cisco Systems\Aironet Client Monitor
Program Folder	Determines the program folder where the ACM software will be installed. You can change the default by entering a new folder name. Default: Cisco Systems
Auto Start	Determines whether ACM starts automatically every time Windows boots. Options: Yes or No Default: Yes Note If you choose No, you can later activate ACM by using Windows Explorer to find the path where the ACM software is installed and double-clicking ACUMon.exe.
Start After Install	Determines whether ACM starts automatically after ACM is installed. Options: Yes or No Default: Yes Note If you choose No, you can later activate ACM by using Windows Explorer to find the path where the ACM software is installed and double-clicking ACUMon.exe.
Program Feature Overrides	Determines which ACM components are enabled. If any components are not selected now and you later want to use them, you must run this installation program again and enable them. Components: See the table below Options per component: Enable or Disable Default per component: Enable
	Component	Description
	About Box (Help)	Displays the ACM version number and enables you to access the online help.
	Exit Program	Closes ACM for all client adapters.
	Launch Aironet Client Utility	Activates ACU, if it is installed.
	Troubleshooting	Activates the troubleshooting utility, which enables you to identify and resolve configuration and association problems with your client adapter.
	Preferences	Enables you to determine when ACM runs and to select the options that appear on the ACM pop-up menu.
	Turn Radio On/Off	Turns the client adapter's radio on or off.
	Reauthenticate	Forces your client adapter to try to reauthenticate using the username and password of the current profile.
	Select Profile	Enables you to select the active profile for your client adapter.
	Auto Profile Selection	Causes the client adapter's driver to automatically select a profile from the list of profiles that were set up in ACU to be included in auto profile selection.
	Other Configuration Application	Enables an application other than ACU to configure the client adapter.
	Show Connection Status	Provides information on the current status of your client adapter.
Menu Options (Defaults)	Determines which options are displayed on the ACM pop-up menu. Menu options: About Box (Help), Exit Program, Launch Aironet Client Utility, Troubleshooting, Turn Radio On/Off, Reauthenticate, Select Profile, Show Connection Status Options per menu option: Show or Hide Default per menu option: Show
Security Modules
LEAP	Installs the LEAP supplicant included in the Install Wizard file. Installing the LEAP supplicant enables you to create a profile in ACU that uses LEAP authentication. If this option is not selected now and you later want to create a profile that uses LEAP, you must run this installation program again and choose this option. Default: Checked Note If you choose LEAP on a Windows XP device, Windows XP's fast user switching feature is disabled.
Allow Saved LEAP User Name and Password	Enables you to create a profile in ACU that uses a saved (rather than temporary) username and password for LEAP authentication. When such a profile is selected, the saved username and password are used to start the LEAP authentication process, and you are not prompted to enter them. Options: Yes or No Default: Yes
EAP-SIM	Installs the EAP-SIM supplicant included in the Install Wizard file. Installing the EAP-SIM supplicant enables the client to support EAP-SIM authentication. If this option is not selected now and you later want to use EAP-SIM, you must run this installation program again and choose this option. Default: Unchecked Note To enable EAP-SIM authentication, your computer must run Windows 2000 with the Microsoft 802.1X supplicant installed or Windows XP. Note If you installed the new EAP-SIM supplicant from Cisco.com (see the "New EAP-SIM Supplicant Available" section), make sure the EAP-SIM option is not selected. Otherwise, the EAP-SIM supplicant included in the Install Wizard file overwrites the new supplicant's settings.
PEAP	Installs the PEAP supplicant included in the Install Wizard file. Installing the PEAP supplicant enables the client to support PEAP authentication. If this option is not selected now and you later want to use PEAP, you must run this installation program again and choose this option. Default: Unchecked Note To enable Cisco PEAP authentication, your computer must run Windows 2000 with the Microsoft 802.1X supplicant installed or Windows XP. Note Service Pack 1 for Windows XP and the Microsoft 802.1X supplicant for Windows 2000 include Microsoft's PEAP supplicant, which supports a Windows username and password only and does not interoperate with Cisco's PEAP supplicant. To use Cisco's PEAP supplicant, install the Install Wizard file after Windows XP Service Pack 1 or the Microsoft 802.1X supplicant for Windows 2000. Otherwise, Cisco's PEAP supplicant is overwritten by Microsoft's PEAP supplicant.
EAP-FAST	Installs the EAP-FAST supplicant included in the Install Wizard file. Installing the EAP-FAST supplicant enables you to create a profile in ACU that uses EAP-FAST authentication. If this option is not selected now and you later want to create a profile that uses EAP-FAST, you must run this installation program again and choose this option. Default: Checked Note The EAP-FAST supplicant is installed and can be enabled only on computers running Windows 2000 or XP. Note If you choose EAP-FAST on a Windows XP device, Windows XP's fast user switching feature is disabled.
Allow Saved EAP-FAST User Name and Password	Enables you to create a profile in ACU that uses a saved (rather than temporary) username and password for EAP-FAST authentication. When such a profile is used, the saved username and password are used to start the EAP-FAST authentication process, and you are not prompted to enter them. Options: Yes or No Default: Yes Note This parameter is applicable only to client adapters that are installed in computers running Windows 2000 or XP.
Allow Auto-Provisioning?	Enables a protected access credentials (PAC) file to be obtained automatically as needed (for instance, when a PAC expires, when the client adapter accesses a different server, when the EAP-FAST username cannot be matched to a previously provisioned PAC, etc.). Options: Yes or No Default: Yes Note This parameter is applicable only to client adapters that are installed in computers running Windows 2000 or XP.

e. When you are finished making selections, click Next.

Step 17 The installation process begins, and you are notified as each component is installed. Perform one of the following:

•If a message appears asking if you wish to reboot now, click Yes.

---

Note To ensure that your client adapter software is installed properly, Cisco recommends that you click Yes to reboot your computer now.

---

•If a message appears indicating that the system is about to reboot, click OK and allow your computer to restart.

•If the following message appears, click OK and then reboot your computer: "The installation will complete and applications will be installed when a wireless LAN client adapter is inserted. If an adapter is already inserted, remove and reinsert the adapter or reboot the machine."

The Found New Hardware screen appears. Depending on your computer's operating system, you may have to click Next. The driver and other software components are installed. Then an ACM icon appears in the Windows system tray (unless you changed the default value during installation). Perform one of the following:

–If a message appears asking if you wish to reboot now, click Yes.

---

Note To ensure that your client adapter software is installed properly, Cisco recommends that you click Yes to reboot your computer now.

---

–If a message appears indicating that the system is about to reboot, click OK and allow your computer to restart.

Step 18 If you want to install a second client adapter, allow your computer to reboot completely; then insert the second adapter into your computer. Depending on your computer's operating system, one of the following scenarios occurs:

•The Found New Hardware Wizard screen appears. Depending on your computer's operating system, you may have to click Next. The driver and other software components are installed, and another ACM icon appears in the Windows system tray. Click Yes or OK when a message appears about rebooting your computer.

---

Note To ensure that your client adapter software is installed properly, Cisco recommends that you reboot your computer now.

---

•The driver and other software components are installed, and another ACM icon appears in the Windows system tray. Click Yes or OK when a message appears about rebooting your computer.

---

Note To ensure that your client adapter software is installed properly, Cisco recommends that you reboot your computer now.

---

Step 19 If your network setup does not include a DHCP server and you plan to use TCP/IP, follow these steps for your operating system. If you have more than one client adapter installed, repeat this step for each adapter.

•Windows 2000—Double-click My Computer, Control Panel, and Network and Dial-up Connections. Right-click Local Area Connection x (where x represents the number of the connection). Click Properties, Internet Protocol (TCP/IP), and Properties. Click Use the following IP address and enter the IP address, subnet mask, and default gateway address of your computer (which can be obtained from your system administrator). Click OK. In the Local Area Connection Properties window, click OK.

•Windows XP—Right-click Wireless Network Connection and click Properties. Click Internet Protocol (TCP/IP) and click Properties. Choose Use the following IP address and enter the IP address, subnet mask, and default gateway address of your computer (which can be obtained from your system administrator). Click OK

Step 20 If you are prompted to restart your computer, click Yes. The installation is complete.

---

Finding Version Numbers

Follow the instructions in this section to find the version numbers of your client adapter's software components.

Finding the Install Wizard Version

Follow these steps to find the version of the Install Wizard that is currently installed for your client adapter.

---

Step 1 Open Windows Explorer.

Step 2 Find the Install Wizard files.

Step 3 Right-click the IWSetup.exe or Setup.exe file.

Step 4 Click Properties.

Step 5 Click the Version tab. The File version field shows the version of the currently installed Install Wizard file.

---

Finding the Firmware and Driver Versions

To find the firmware and driver versions that are currently installed for your client adapter, click the ACU Status icon. The Firmware Version field on the Status screen shows the current firmware version, and the NDIS Driver Version field shows the current driver version.

Finding the ACU Version

To find the version of ACU that is currently installed for your client adapter, click the ACU About icon. The About Aironet Client Utility screen shows the current ACU version.

Finding the ACM Version

To find the version of ACM that is currently installed for your client adapter, right-click the ACM icon and click the About option. The About screen shows the current ACM version.

Caveats

This section describes open and resolved caveats for the software components in this release.

Open Caveats

Open Driver Caveats

The following caveats are not resolved in PC, LM, and PCI card driver 8.5.26 and mini PCI and PC-Cardbus card driver 3.8.26.

•CSCec13533—Login delay using Microsoft WPA supplicant

When you activate a host-based EAP profile under Windows XP with Microsoft's WPA supplicant (Q815485) installed, it can take up to 90 seconds after login for the Windows desktop to appear and several minutes for the client to authenticate.

•CSCec33661—Some Dell laptops fail to obtain IP address

Some Dell laptops fail to obtain an IP address from the DHCP server after being undocked. To work around this issue, restart your computer.

•CSCec47650—Dell Inspiron 8000 shuts down when Windows 2000 3D screen saver used

The Dell Inspiron 8000 laptop may shut down upon entering screen saver mode when a 3D screen saver is used. To work around this issue, choose a non-3D screen saver.

Open ACU Caveats

The following caveats are not resolved in ACU 6.3.

•CSCec27947—ACU and ACM show broadcast SSID rather than associated SSID

On Windows XP devices, ACM and the ACU Status screen sometimes show the access point's broadcast SSID rather than the SSID to which the client adapter is associated.

•CSCec39505—ACU sometimes misreports signal strength for CB20A client adapters

The ACU Status screen sometimes misreports a signal strength of 100% for CB20A client adapters.

•CSCin58253—PEAP Login screen takes a long time to display for WPA clients

The PEAP login screen (Static Password or One Time Password) can take up to 3 minutes to display after you activate a profile that is configured for PEAP and WPA.

Open ACM Caveats

The following caveats are not resolved in ACM 2.3.

•CSCed45720—ACUMon.Exe error occurs if client adapter is not inserted during software upgrade

If the client adapter is not inserted when you attempt to upgrade to client adapter Install Wizard 1.4, the ACUMon.Exe error occurs. To work around this issue, simply insert your client adapter and continue the software upgrade process.

•CSCec06303—ACM icon disappears from system tray

The ACM icon may disappear from the Windows system tray while ACM is running.

Open Security Module Caveats

The following caveats are not resolved in EAP-FAST security module 1.0 and PEAP security module 1.2.

•CSCed90666—EAP-FAST may require multiple initial provisioning attempts

If you have a domain, rather than a local, account and do not have a pre-existing PAC, you are required to automatically provision a PAC twice.

•CSCin32330—Many PEAP login screens appear when computer is left idle

If you leave your computer idle while it is using PEAP authentication, you may receive three PEAP login screens upon resume. To resolve this problem, cancel the first two login screens and use the last one (which is on top) to log in.

Other Open Caveats

The following caveat is not resolved in Cisco IOS Release 12.2(13)JA and affects the behavior of Cisco Aironet client adapters running Install Wizard 1.4.

•CSCed54143—Session disconnects may occur during password changes when using PEAP-GTC

If you are using PEAP-GTC with a Cisco Secure ACS server and you are prompted to change your password, a message appears when you are done indicating that the password change was performed; however, the session may disconnect.

Resolved Caveats

Resolved Install Wizard Caveats

The following caveats are resolved in Install Wizard 1.4.

•CSCed14388—Install Wizard fails for non-English Windows operating systems

When you run Install Wizard 1.2 or 1.3 on a non-English-based Windows operating system, the following error message appears: "Administrator privileges are required to run the installation. Please log in as an administrator to run this installation. Select OK to exit."

•CSCed94476—Uninstalling ACU 6.x prevents changes to Windows font settings

When you uninstall ACU 6.x, the Install Wizard deletes the layout.inf file from the Windows\Inf directory (for example, C:\WINNT\Inf), which consequently prevents you from changing the size of Windows fonts. To work around this issue, copy the layout.inf file from another location on your computer (such as the directory containing your Windows installation files or service pack installation files), from your Windows installation disk, or from another computer running the same operating system with files of similar vintage, and paste it into your Windows\Inf directory.

---

Note You can use the Windows Search option to find the layout.inf file. Make sure you set the tool to show hidden files and folders. The layout.inf file will most likely be in the I386 subdirectory of the Windows installation files or service pack installation files.

---

Resolved Firmware Caveats

The following caveats are resolved in firmware 5.41.00.

•CSCed75714—WPA client may take up to 5 minutes to associate to 11g access point

The client adapter may take up to 5 minutes to associate to an 802.11g access point when the following settings are enabled: WPA or WPA-PSK, IP phone QOS element, and low power (less than 100 mW).

•CSCin51159—ACU Status screen and ACM Connection Status screen may display incorrect SSID

If your client adapter is configured with multiple profiles, the ACU Status screen and ACM Connection Status screen may incorrectly display the SSID of a profile that is not is use. However, the functionality of your client adapter is not affected.

Resolved Driver Caveats

The following caveat is resolved in PC, LM, and PCI card driver 8.5.26 and mini PCI and PC-Cardbus card driver 3.8.26.

•CSCed95974—Network traffic may be interrupted by Windows XP scan requests

If your client adapter is installed in a Windows XP computer but is configured using ACU, network traffic may be interrupted by scan requests from the Windows XP operating system. Drivers 8.5.26 and 3.8.26 resolve this issue by blocking Windows XP scan requests whenever the Use Another Application to Configure My Wireless Settings option is not selected on ACU's profile manager Select Profile screen.

Resolved Security Module Caveats

The following caveats are resolved in LEAP security module 6.3.21.

•CSCee21739—Cisco GINA fails to recognize when Novell Client software is uninstalled

If your computer has both LEAP and Novell Client software installed, you are prompted to enter separate LEAP credentials. This is the expected behavior. However, if you uninstall the Novell software, the Cisco GINA continues to prompt for a separate username and password rather than obtaining the credentials from the Windows login prompt.

•CSCed91193—EAP-FAST Authentication Status screen appears during LEAP authentication

If you select an EAP-FAST profile with an SSID that is not available and then select a LEAP profile whose SSID is available, the client adapter successfully LEAP authenticates. However, the Authentication Status screen shows EAP-FAST authenticated.

Getting Bug Information on Cisco.com

If you are a Cisco registered user, you can use the Cisco TAC Software Bug Toolkit, which consists of three tools (Bug Navigator, Bug Watcher, and Search by Bug ID Number) that help you to identify existing bugs (or caveats) in Cisco software products.

Access the TAC Software Bug Toolkit at the following URL:

http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl

Troubleshooting

For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at

http://www.cisco.com/en/US/support/index.html

Click Product Support > Wireless. Then choose your product and Troubleshooting to find information on the problem you are experiencing.

Related Documentation

For more information about Cisco Aironet 350 and CB20A client adapters for Windows, refer to the following documents:

•Cisco Aironet 340, 350, and CB20A Wireless LAN Client Adapters Installation and Configuration Guide for Windows, OL-1394-08

http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/350cards/windows/index.htm

•Release Notes for Cisco Aironet 350 and CB20A Client Adapter Firmware 5.41.00, OL-5986-01

http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/350cards/windows/firmrn/index.htm

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation on the World Wide Web at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

International Cisco websites can be accessed from this URL:

http://www.cisco.com/public/countries_languages.shtml

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:

http://www.cisco.com/en/US/partner/ordering/index.shtml

•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).

Documentation Feedback

You can submit e-mail comments about technical documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services, online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.

Cisco TAC Website

The Cisco TAC website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365 days a year. The Cisco TAC website is located at this URL:

http://www.cisco.com/tac

Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a login ID or password, register at this URL:

http://tools.cisco.com/RPF/register/register.do

Opening a TAC Case

Using the online TAC Case Open Tool is the fastest way to open P3 and P4 cases. (P3 and P4 cases are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Case Open Tool automatically recommends resources for an immediate solution. If your issue is not resolved using the recommended resources, your case will be assigned to a Cisco TAC engineer. The online TAC Case Open Tool is located at this URL:

http://www.cisco.com/tac/caseopen

For P1 or P2 cases (P1 and P2 cases are those in which your production network is down or severely degraded) or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly.

To open a case by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447

For a complete listing of Cisco TAC contacts, go to this URL:

http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

TAC Case Priority Definitions

To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.

Priority 1 (P1)—Your network is "down" or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Priority 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Priority 3 (P3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Priority 4 (P4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

•Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Go to this URL to visit the company store:

http://www.cisco.com/go/marketplace/

•The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:

http://cisco.com/univercd/cc/td/doc/pcat/

•Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press online at this URL:

http://www.ciscopress.com

•Packet magazine is the Cisco quarterly publication that provides the latest networking trends, technology breakthroughs, and Cisco products and solutions to help industry professionals get the most from their networking investment. Included are networking deployment and troubleshooting tips, configuration examples, customer case studies, tutorials and training, certification information, and links to numerous in-depth online resources. You can access Packet magazine at this URL:

http://www.cisco.com/packet

•iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet business strategies for executives. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

•Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

•Training—Cisco offers world-class networking training. Current offerings in network training are listed at this URL:

http://www.cisco.com/en/US/learning/index.html

This document is to be used in conjunction with the documents listed in the "Related Documentation" section.

CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0403R)

Copyright © 2004 Cisco Systems, Inc.
All rights reserved.