Cisco Wireless LAN Controller System Message Guide
PKTDEBUG through SIM
Downloads: This chapterpdf (PDF - 335.0KB) The complete bookPDF (PDF - 15.88MB) | Feedback

PKTDEBUG Messages

Table Of Contents

PKTDEBUG Messages

PMALLOC Messages

POE Messages

POLICY Messages

POWER Messages

PPTP Messages

RBCP Messages

RFID Messages

RRM Messages

SIM Messages


PKTDEBUG Messages

This section contains packet debugging (PKTDEBUG) messages.

Error Message    %PKTDEBUG-6-MSGTAG001: Starting packet log 

Explanation    The packet logging service was enabled.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PKTDEBUG-6-MSGTAG002: Stopping packet log 

Explanation    The packet logging service was disabled.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PKTDEBUG-6-MSGTAG003: Packet log displayed [int] of [int] packets 

Explanation    The packet logging service displayed the requested number of packets and will now terminate.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PKTDEBUG-2-MSGTAG009: Failed to create PKTDEBUG socket rx task.. 

Explanation    PKTDEBUG task failed to start correctly.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PKTDEBUG-2-MSGTAG010: Unable to open PKTDEBUG socket 

Explanation    PKTDEBUG task failed to start correctly.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PKTDEBUG-3-MSGTAG012: select from PKTDEBUG socket failed with error 
[dec] 

Explanation    PKTDEBUG task is experiencing problems while processing packets.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PKTDEBUG-3-MSGTAG014: read from dtl PKTDEBUG socket failed. 

Explanation    PKTDEBUG task is experiencing problems while processing packets.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

PMALLOC Messages

This section contains memory pool (PMALLOC) messages.

Error Message    %PMALLOC-0-ALLOC_POOL_FAILED: Out of memory! Unable to allocate a 
chunk for pool [dec]!. 

Explanation    Out of memory! Unable to allocate a chunk for a pool!.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PMALLOC-0-INVALID_POOL_INFO: Invalid poolinfo. Last entry in the 
poolinfo must be zero.. 

Explanation    Invalid poolinfo. Last entry in the poolinfo must be zero..

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PMALLOC-7-MEM_ALLOC_DETAIL: Allocating [dec] bytes into [dec] byte 
pool. 

Explanation    The memory allocation details are displayed.

Recommended Action    No action is required.

Error Message    %PMALLOC-0-MEM_ALLOC_FAILED: Out of memory.Unable to allocate [dec] 
bytes!. 

Explanation    Unable to allocate specific number of bytes.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PMALLOC-7-MEM_ALLOC_RAWPOOL: Allocating [dec] bytes into RAW pool. 

Explanation    The memory allocation details are displayed.

Recommended Action    No action is required.

Error Message    %PMALLOC-0-MEM_THRESHOLD_REACHED: Memory threshold reached. Not 
allocating memory. 

Explanation    Memory threshold reached. Not allocating memory.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

POE Messages

This section contains Power over Ethernet (POE) messages.

Error Message    %POE-3-PORT_RESYNC: poePortResync returned FAILURE.  

Explanation    poePortResync returned FAILURE. Inconsistency in internal data structures

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %POE-0-RESET_FAIL: Unable to reset the Power Supply for [dec] times. 
Will try to reset for another [dec] times. 

Explanation    Failure to reset POE device. Will try to reset again. It is a fatal Error if the POE device cannot be reset after a maximum number of retries.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

POLICY Messages

This section contains policy (POLICY) messages.

Error Message    %POLICY-6-TRANSPORT_MODE_UPGRADE: Switch Transport Mode Upgraded to 
Layer 3 during Configuration 

Explanation    The configuration was upgraded from Layer 2 to Layer 3 transport mode. Layer 2 is no longer supported. The possible reason for this change is an image upgrade from software release 4.2.x.x.

Recommended Action    No action is required.

POWER Messages

This section contains power (POWER) messages.

Error Message    %POWER-3-FAN_FAIL: [chars] 

Explanation    The specified fan is not functioning properly and has failed

Recommended Action    No action is required.

Error Message    %POWER-6-FAN_OK: [chars] 

Explanation    The specified fan is functioning normally and is OK.

Recommended Action    No action is required.

Error Message    %POWER-6-PS_DETECT: [chars] 

Explanation    Indicates whether the Power Supply is Present or Not.

Recommended Action    No action is required.

Error Message    %POWER-3-PS_FAIL: [chars] 

Explanation    The specified Power Supply has failed.

Recommended Action    No action is required.

Error Message    %POWER-6-PS_OK: [chars] 

Explanation    The specified power supply is functioning OK.

Recommended Action    No action is required.

PPTP Messages

This section contains Point-to-Point Tunneling Protocol (PPTP) messages.

Error Message    %PPTP-1-CONFIG_SAVE_ERROR: Error on call to osapiFsWrite routine on 
config file [chars]. 

Explanation    PPTP Configuration changes could not be saved.

Recommended Action    Please try to reconfigure PPTP parameters and save.

Error Message    %PPTP-1-LOCAL_IP_NOT_FOUND: unable to determine our own local IP 
address - pptp will be disabled. 

Explanation    unable to determine our own local IP address - pptp will be disabled.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PPTP-1-SOCKET_CONFIG_ERROR: unable to configure socket - pptp will be 
disabled... 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PPTP-1-SOCKET_CONFIG_RETRIEVE_ERROR: unable to retrieve socket 
configuration - pptp will be disabled... 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PPTP-1-SOCKET_OPEN_ERROR: Unable to open listener socket - pptp will 
be disabled... 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PPTP-1-SOCKET_SELECT_ERROR: select failed for no apparent reason - 
pptp will be disabled... 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PPTP-2-TASK_CREATE_ERROR: Failed to create pptp main task.. 

Explanation    The PPTP task failed to start correctly.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PPTP-2-TASK_INIT_ERROR1: Unable to open listener socket. 

Explanation    The PPTP task failed to start correctly.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PPTP-2-TASK_INIT_ERROR2: Unable to bind listener socket. 

Explanation    The PPTP task failed to start correctly.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PPTP-2-TASK_INIT_ERROR3: Unable to listen on listener socket. 

Explanation    The PPTP task failed to start correctly.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

RBCP Messages

This section contains Router Blade Control Protocol (RBCP) messages.

Error Message    %RBCP-0-MSGQ_CREAT_FAILED: Failed to create RBCP osapi Queue. 

Explanation    Failed to create RBCP osapi Queue.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RBCP-3-PDU_TRANSMIT_FAILED: Failed to transmit the RBCP 
register.Return code=[dec]. 

Explanation    Failed to transmit the RBCP register.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RBCP-0-PORT_NOT_UP: Port 1 not up. Cant plumb Code version. 

Explanation    Port 1 not up. Cant plumb Code version.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RBCP-0-PROD_VER_SET_FAILED: Driver api failed for the command 
[chars].Cant plumb Code version.Return Code=[dec]. 

Explanation    Driver api failed. Cant plumb Code version.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RBCP-0-RBCP_RECVQ_NULL: No RBCP Receive Queue available.Unable to 
receive RBCP messages 

Explanation    No RBCP Receive Queue available.Unable to receive RBCP messages

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RBCP-0-RBCP_REGISTRATION_FAILED: RBCP registration failed.Return 
Code=[dec]. 

Explanation    RBCP registration failed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RBCP-3-RBCP_TX_FAILED: Failed to generate a  RBCP platform 
response.Return code=[dec]. 

Explanation    Failed to generate a RBCP platform response.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RBCP-0-TASK_CREAT_FAILED: Failed to create RBCP receive task. 

Explanation    Failed to create RBCP receive task.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

RFID Messages

This section contains radio frequency identification (RFID) messages.

Error Message    %RFID-3-BAD_RSSI_EXPIRY: Illegal rfid expiry value [int]-- defaulting. 

Explanation    Illegal rfid expiry value -- defaulting.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-BAD_RSSI_HALFLIFE: Illegal rfid rssi half life value [int]-- 
defaulting. 

Explanation    Illegal rfid rssi half life value -- defaulting.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-BAD_TIMEOUT: Illegal rfid timeout value [int]-- defaulting. 

Explanation    Illegal rfid timeout value -- defaulting.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-BLUESOFT_FAIL: Unable to register for bluesoft tag data - error 
[dec]  

Explanation    Unable to register for bluesoft tag data

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-CISCO_FAIL: Unable to register for Cisco tag data - error [dec]  

Explanation    Unable to register for Cisco tag data

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-CONFIG_WRITE_FAIL: Unable to write rfid configuration file. 

Explanation    Unable to write rfid configuration file.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-CREATE_DB_FAIL: Unable to create rfid database  

Explanation    Unable to create rfid database

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-CREATE_Q_FAIL: Unable to create rfid interface  

Explanation    Unable to create rfid internal queue interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-DEL_FAIL: Error! Can not delete entry from rfid Table  

Explanation    Error! Can not delete entry from rfid Table

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-DUP_ENTRY: Duplicate entry found on rfid tree. 

Explanation    Duplicate entry found on rfid tree.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-NO_CFG_FILE: Error retrieving file [chars]. 

Explanation    Error retrieving file .

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-NO_LOAD_CFG: Unable to load rfid configuration  

Explanation    Unable to load rfid configuration

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-NOTIFICATION_TIMER_NOT_CREATED: [chars] Could not create 
Rfid-Locp Notification timer...  

Explanation    Could not create Rfid-Locp Notification timer...

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-TCB_FAIL: rfid rx task did not receive a task control block 
--exiting 

Explanation    rfid rx task did not receive a task control block --exiting

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RFID-3-TIMER_FAIL: unable to create rfid task timer  

Explanation    unable to create rfid task timer

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

RRM Messages

This section contains Radio Resource Management (RRM) messages.

Error Message    %RRM-3-AP_DB_ERR1: Unable to find AP 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] entry in the database, could not process 
[chars]  

Explanation    The operation being performed for the AP failed because the internal entry for the AP was not found. It is possible that the AP has been removed from the controller.

Recommended Action    Use the 'show ap summary' command to determine if the AP is still joined to the controller. If it is not, the message may be ignored. If it is still joined, restart the AP to ensure that it has the latest configuration and contact technical assistance if the problem recurs.

Error Message    %RRM-3-AP_DB_ERR2: Invalid slot number [dec] for  AP 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] could not process [chars]  

Explanation    AP included wrong slot number

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-3-FAILEDCOVERAGEPROFILE: [chars]: Coverage profile violation on 
[chars] AP[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] 

Explanation    Coverage profile violation

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-3-FAILEDINTPROFILE: [chars]: Interference profile violation on 
[chars] AP[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] 

Explanation    Interference profile violation

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-3-FAILEDLOADPROFILE: [chars]: Load profile violation on [chars] 
AP [hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] 

Explanation    Load profile violation

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-3-FAILEDNOISEPROFILE: [chars]: Noise profile violation on [chars] 
AP [hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] 

Explanation    Noise profile violation

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-3-FAILEDRMCLIDB_ADD: Adding to CCX RM Client Database failed 
for[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Adding to CCX RM Client Database failed

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-0-FAILEDTIMERCREATE: RRM failed to create timer 

Explanation    Failed to create timer

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-6-GETRFDOMAINNAME: [chars]: Read RF domain name as [chars] 

Explanation    Get RF domain name

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-3-INVALIDRFDOMAINNAME: [chars]: Could not read valid RF domain 
name 

Explanation    Invalid RF domain name

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-3-MSGTAG021: [chars]: Unable to queue enchanced coverage data 
from AP [chars] on [chars] 

Explanation    [chars]: Unable to queue enchanced coverage data from AP [chars] on [chars].

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-6-PASSEDCOVERAGEPROFILE: [chars]: Coverage profile recovery on 
[chars] AP[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] 

Explanation    Coverage profile recovery

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-6-PASSEDINTPROFILE: [chars]: Interference profile recovery on 
[chars] AP[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] 

Explanation    Interference profile recovery

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-6-PASSEDLOADPROFILE: [chars]: Load profile recovery on [chars] AP 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] 

Explanation    Load profile recovery

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-6-PASSEDNOISEPROFILE: [chars]: Noise profile recovery on [chars] 
AP [hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] 

Explanation    Noise profile recovery

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-3-REACHEDMAXCLIENTS: Reached max Rm clients. 
dropping[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Reached max Rm clients

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-3-RRM_LOGMSG: RRM LOG: [chars] 

Explanation    RRM LOG.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %RRM-6-SETCHANNEL: set channel on cell 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] to [dec] to reduce co-channel 
interference from [dec] to [dec] 

Explanation    Set channel to reduce co-channel interference

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-6-SETRFDOMAINNAME: [chars]: Change RF domain name to [chars] 

Explanation    Set RF domain name

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-6-SETTXPOWER: [chars]: Set transmit power on [chars] AP 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] to [int] 

Explanation    Set transmit power

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-6-UPDATECHANNEL: [chars]: Set channel on [chars] AP 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] to [dec] by configuration change 

Explanation    Channel configuration change

Recommended Action    This is a debug message only. No action is required.

Error Message    %RRM-6-UPDATETXPOWER: [chars]: Set transmit power on [chars] AP 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex]::[dec] to [int] 

Explanation    Transmit power configuration change

Recommended Action    This is a debug message only. No action is required.

SIM Messages

This section contains subscriber identity module (SIM) messages.

Error Message    %SIM-7-ADDR_CHANGE_DTL: Address changed to dtl successfully. 
[int].[int].[int].[int] ==> [int].[int].[int].[int] (rc [dec]) 

Explanation    Address changed to dtl successfully

Recommended Action    No action is required.

Error Message    %SIM-3-ADDR_INFO_FAIL: Unable to retrieve client Ip info. Ip Addr: 
[int].[int].[int].[int] 

Explanation    Unable to retrieve client Ip info

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-4-ADD_VLAN_NPU_FAIL: Failed to add/remove/update vlan information 
into NPU.vlan [int], intf [int] 

Explanation    Failed to add/remove/update vlan information into NPU

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-APMGR_CONF_FAIL: Failed to configure AP-Manager. Cannot 
configure AP-Manager When LinkAggregation is enabled  

Explanation    Failed to configure AP-Manager. Cannot configure AP-Manager When LinkAggregation is enabled

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-APPLY_CONFIG_FAIL: Unable to apply SIM Configuration data 

Explanation    Unable to apply SIM Configuration data

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-ARP_SND_FAIL: Unable to send ARP Request. Local MAC: 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex].Ip Addr: [int].[int].[int].[int]Interface # 
[dec]. Vlan Id: [dec] 

Explanation    Unable to send ARP Request.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-CREATE_AP_INTERFACE_FAIL: Unable to create AP manager interface 

Explanation    Unable to create AP manager interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-CREATE_INTF_FAIL: Unable to create the [chars] interface 

Explanation    Unable to create an interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-0-CREATE_TASK_FAIL: Failed to Create Transfer Task. The cli, web 
or snmp may not be initialized 

Explanation    Failed to Create Transfer Task. The cli, web or snmp may not be initialized

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-CREATE_VLAN_FAIL: Unable to create VLAN Interface [chars] 

Explanation    Unable to create a VLAN Interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-DEL_INTF_APGROUPMAP_FAIL: AP Group vlan is mapped to this 
Interface.  

Explanation    AP Group vlan is mapped to this Interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-DEL_INTF_FAIL: Unable to delete interface [chars] form AVL 
Tree. Internal System Error 

Explanation    Unable to delete an interface from AVL Tree. Internal System Error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-DEL_INTF_WLANMAP_FAIL: A Wireless LAN is assigned to this 
Interface.  

Explanation    A Wireless LAN is assigned to this Interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-DHCP_CONF_FAIL: Unable to set service port protocol.DHCP server 
failed to be configured 

Explanation    Unable to set service port protocol.DHCP server failed to be configured

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-DS_CONF_FAIL: Failed to configure the Distribution system 
Interface.Old Port: [dec]. New Port: [dec] 

Explanation    Failed to configure the Distribution system Interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-DS_DEL_FAIL: Failed to delete the distribution system interface 
[chars]. Port # [dec] 

Explanation    Failed to delete a distribution system interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-ENTRY_CREATE_FAIL: Failed to create a Qos profile. Profile 
Name: [chars] 

Explanation    Failed to create a Qos profile.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-FILE_OPEN_FAIL: Unable to open file <[chars]>: [dec]:[chars]. 

Explanation    Unable to open a file

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-FILE_READ_FAIL: Failed to read config file [chars]. 

Explanation    Failed to read config file.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-FILE_WRITE_FAIL: Failed to Write to config file [chars]. 

Explanation    Failed to Write to config file.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-FLASH_READ_FAIL: Error loading '[chars]' file from flash 

Explanation    Error loading file from flash

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-7-GUEST_VLAN_ENABLE_FAIL: Guest VLAN enable failed since either 
IP or DHCP configuration could not be cleared for interface [chars]. 

Explanation    The enabling of guest VLAN functionality failed because either the IP or the DHCP configuration could not be cleared for the interface.

Recommended Action    No action is required.

Error Message    %SIM-3-INTF_DTL_FAIL: Failed to set the Interface in the device 
transformation layer.Interface Name: [chars]Failed to resolve Gateway MAC 

Explanation    Failed to set the Interface in the device transformation layer.Failed to resolve Gateway MAC

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-6-INTF_FIND_FAIL: Could not find interface [chars]. 

Explanation    Could not find an interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-INTFGET_GIG_ETH_FAIL: Failed to get the Interface number of the 
Gigabit Ethernet Port 

Explanation    Failed to get the Interface number of the Gigabit Ethernet Port

Recommended Action    No action is required.

Error Message    %SIM-6-INTF_IN_USE: WLANs enabled for the interface. Disable all WLANs 
to configure port. Interface Name:[chars] 

Explanation    WLANs enabled for the interface. Disable all WLANs to configure port.

Recommended Action    No action is required.

Error Message    %SIM-3-INTF_PORTSET_FAIL: Failed to set the port number to [dec] for 
the interface name '[chars]' 

Explanation    Failed to set the port number for the interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-INVALID_BAUD_RATE: Invalid baudrate [dec].Setting to 
default:9600 baud. 

Explanation    Invalid baudrate, Possible Values are 1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200. Setting to default:9600 baud.

Recommended Action    No action is required.

Error Message    %SIM-3-INVALID_INTF: Cannot set the specified interface number 

Explanation    Cannot set the specified interface number

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-INVALID_PORT: Using invalid port number. Port out of range. Port 
# [int] 

Explanation    Using invalid port number. Port out of range.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-INVALID_PORT_NUM: Invalid Port # [dec] 

Explanation    Invalid Port Number

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-INVALID_VLANID: Using invalid VLAN ID.Vlan Id out of range. Vlan 
# [int] 

Explanation    Using invalid VLAN ID. Vlan Id out of range

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-6-LAG_ALREADY_CONF: Link Aggregation is already set to the same 
Configuration. 

Explanation    Link Aggregation is already set to the same Configuration.

Recommended Action    No action is required.

Error Message    %SIM-3-LAG_DSBL_PORT_ENBL: LAG disabled but Primary Port enabled 

Explanation    LAG disabled but Primary Port enabled

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-LAG_ENBL_PORT_DSBL: LAG enabled but Primary Port disabled 

Explanation    LAG enabled but Primary Port disabled

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-LAG_INIT_FAIL: Failed to initialize link aggregation. Error 
Code:[int] 

Explanation    Failed to initialize link aggregation

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-7-LAG_INTF_CREATED: LAG Interface (port [int]) created... 

Explanation    LAG Interface created...

Recommended Action    No action is required.

Error Message    %SIM-6-LAG_INTF_DEL: Link Aggregation Enabled.Dynamic Interface 
'[chars]' deleted 

Explanation    Link Aggregation Enabled. All Dynamic Interfaces deleted

Recommended Action    No action is required.

Error Message    %SIM-3-LAG_INTF_DEL_FAIL: Failed to delete interface '[chars]' 

Explanation    Failed to delete dynamic interface while enabling Link Aggregation

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-LAG_INTF_TO_PORT_MAP: Failed to map LAG interfaces to LAG 
ports. Error Code [int] 

Explanation    Failed to map LAG interfaces to LAG ports. Link Aggregation Malfunctioned.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-4-LAG_IN_TRANSITION: LAG in transition. switch reboot DUE..!!!  

Explanation    LAG in transition. switch reboot DUE..!!!

Recommended Action    No action is required.

Error Message    %SIM-3-LAG_PORTADD_FAIL: Failed to add port for LAG. Error code [int]. 
Port # [int] 

Explanation    Failed to add a Physical Port to link Aggregation

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-LAG_PORT_CHANGE_FAIL: Failed to change the Link Aggregation 
port status. Port # [dec] 

Explanation    Failed to change the Link Aggregation port status

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-6-LAG_WLAN_DISABLED: Link Aggregation Enabled. WLAN [int] 
disabled and set to interface [chars] 

Explanation    Link Aggregation Enabled. WLAN disabled and Re-Mapped.

Recommended Action    No action is required.

Error Message    %SIM-3-LVL7_TO_BAUD_FAIL: Invalid baud value [dec], returning baudrate 
of 9600. 

Explanation    Invalid baud value, returning baudrate of 9600.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-MACADDR_GET_FAIL: Interface [dec] source MAC address is not 
found. 

Explanation    Interface source MAC address is not found.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-MACADDR_READ_FAIL: Failed to retrieve MAC Address from registry 

Explanation    Failed to retrieve a MAC Address

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-MAXLEN_DESC_FAIL: Failed to read/write the profile description. 
Profile Too Big. Profile Name:[chars] 

Explanation    Failed to read/write the profile description. Profile Too Big.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-MEM_ALLOC_FAIL: Interface File migration failed - OUT OF 
MEMORY!!!. 

Explanation    Interface File migration failed - OUT OF MEMORY!!!.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-MIG_OLD_CFG: Interface File migration failed - OUT OF DATED CFG 
!!!. 

Explanation    Interface File migration failed - OUT OF DATED CFG !!!.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-MLTP_UNTG_INTF: Multiple untagged interfaces on same port not 
allowed 

Explanation    Multiple untagged interfaces on same port not allowed

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-NPU_IPADD_FAIL: Failed to add the Ip Address of a client in the 
NPU. IP: [int].[int].[int].[int].MAC: [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Failed to add Ip Address of a client in the NPU

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-4-NPU_IPDEL_FAIL: Failed to delete the Ip Address of a client from 
the NPU. IP: [int].[int].[int].[int]MAC: [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Failed to delete the Ip Address of a client form the NPU.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-7-PHASE2_LAG_INIT: Phase2 of LAG Initialization... 

Explanation    Phase2 of LAG Initialization...

Recommended Action    No action is required.

Error Message    %SIM-7-PHASE2_LAG_INIT_DONE: Phase2 of LAG Initialization...done. 

Explanation    Phase2 of LAG Initialization...done.

Recommended Action    No action is required.

Error Message    %SIM-7-PORT_CHANGED: interface '[chars]' port changed to 1 

Explanation    interface port changed to 1

Recommended Action    No action is required.

Error Message    %SIM-7-PORT_DEL_START:  Starting Port delete from NPU. vlan=[dec], 
intf ID=[dec] 

Explanation    Starting Port delete from NPU

Recommended Action    No action is required.

Error Message    %SIM-3-PORT_DOWN: Physical port [dec] is down!. 

Explanation    A Physical port is down!.

Recommended Action    No action is required.

Error Message    %SIM-6-PORT_FAIL: Port [[dec]] Out of Range for LAG. Valid Range is 
[dec] - [dec]  

Explanation    Requested Port Out of Range for LAG

Recommended Action    No action is required.

Error Message    %SIM-3-PORT_GETSTATE_FAIL: Unable to get link state for port [dec] of 
interface[chars]. 

Explanation    Unable to get link state for a port

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-7-PORT_NPU_ADD_START: Starting Port Add To NPU. vlan=[dec], 
port=[dec], portBitMap=[hex] 

Explanation    Starting Port Add To NPU.

Recommended Action    No action is required.

Error Message    %SIM-3-PORT_UP: Physical port [dec] is up!. 

Explanation    Physical port is up!.

Recommended Action    No action is required.

Error Message    %SIM-7-PORT_UPDATE_START: Vlan Port Update Start. oldPort:[dec] 
newPort:[dec] oldVlan:[dec] newVlan:[dec] vlanName:[chars] 

Explanation    VLAN Port Update Start

Recommended Action    No action is required.

Error Message    %SIM-3-QOS_ACIMAP_FAIL: Unable to set [chars] Adjacent Channel 
Interference (ACI) map 

Explanation    Unable to set Profile Adjacent Channel Interference (ACI) map

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_ACM_DOT1A_FAIL: Unable to set [chars] Admission Control 
(ACM) 

Explanation    Unable to set Admission Control (ACM)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_ACM_DOT1BG_FAIL: Unable to set [chars] Admission Control 
(ACM) 

Explanation    Unable to set Admission Control (ACM)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_AIFS_FAIL: Unable to set [chars] Arbitration Interframe 
Space (AIFS) 

Explanation    Unable to set Arbitration Interframe Space (AIFS)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_AVGBW_FAIL: Unable to set [chars] Profile Real-Time and 
Data Bandwidth Contract (Average) 

Explanation    Unable to set Profile Real-Time and Data Bandwidth Contract (Average)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_BURSTBW_FAIL: Unable to set [chars] Real-Time or Data 
Bandwidth Contract (Burst) 

Explanation    Unable to set Real-Time or Data Bandwidth Contract (Burst)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_CREATE_PROFILE: Unable to create [chars] QOS Profile 

Explanation    Unable to create QOS Profile

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_CWMAX_FAIL: Unable to set [chars] Maximum Contention Window 
(CwMax) 

Explanation    Unable to set Maximum Contention Window (CwMax)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_CWMIN_FAIL: Unable to set [chars] Minimum Contention Window 
(CwMin) 

Explanation    Unable to set Minimum Contention Window (CwMin)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_DOT1P_FAIL: Unable to set [chars] 802.1P Tag 

Explanation    Unable to set 802.1P Tag

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_DSCP_FAIL: Unable to set [chars] Differentiated Service 
Code Point (DSCP) 

Explanation    Unable to set Differentiated Service Code Point (DSCP)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_INIT_FAIL: Error! Couldn't load qos configuration at 
initialization 

Explanation    Error! Couldn't load qos configuration at initialization

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-6-QOS_NAME_INVALID: Qos Profile Name Invalid. Profile Name Too 
Long or No Profile Name Given 

Explanation    Qos Profile Name Invalid. Profile Name Too Long or No Profile Name Given

Recommended Action    No action is required.

Error Message    %SIM-3-QOS_PROFILE_DESC_SET: Unable to set [chars] QOS Profile 
Description 

Explanation    Unable to set QOS Profile Description

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_QUEUE_DEPTH_FAIL: Unable to set [chars] Queue Depth 

Explanation    Unable to set Queue Depth

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_RF_USAGE_FAIL: Unable to set [chars] RF Usage 

Explanation    Unable to set RF Usage

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-6-QOS_SAME_PROFILE: QOS Profile Name [chars] already set. Cannot 
apply the same profile. 

Explanation    QOS Profile Already set. Cannot apply the same profile.

Recommended Action    No action is required.

Error Message    %SIM-3-QOS_TXOP_FAIL: Unable to set [chars] Transmission Opportunity 
(Txop) 

Explanation    Unable to set Transmission Opportunity (Txop)

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QOS_WIRED_PROTOCOL_FAIL: Unable to set [chars] Wired Protocol 

Explanation    Unable to set Wired Protocol

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-QVLAN_CREATE_FAILED: Attempt to create a new quarantine VLAN 
[chars] failed.  

Explanation    When a quarantine VLAN is assigned to an interface the system internally creates an interface .sys.quarantine-<port

Recommended Action    No action is required.

Error Message    %SIM-3-QVLAN_DEL_FAILED: Attempt to delete existing quarantine VLAN 
[chars] failed.  

Explanation    When the quarantine VLAN is changed on an interface, the system attepts to delete the old quarantine VLAN. This delete operation failed.

Recommended Action    No action is required.

Error Message    %SIM-3-QVLAN_EXISTS: Attempt to assigned quarantine VLAN [int] to 
interface [chars] failed. VLAN [int] already exists as interface [chars].  

Explanation    The quarantine VLAN must not be assigned to any other port/vlan combination.

Recommended Action    No action is required.

Error Message    %SIM-3-QVLAN_FIND2_FAILED: Unable to find quarantine vlan [int] in the 
interface db.  

Explanation    When a quarantine VLAN is assigned to an interface the system internally creates an interface .sys.quarantine-<port

Recommended Action    No action is required.

Error Message    %SIM-3-QVLAN_FIND_FAILED: Unable to find quarantine interface [chars] 
in the interface db.  

Explanation    When a quarantine VLAN is assigned to an interface the system internally creates an interface .sys.quarantine-<port

Recommended Action    No action is required.

Error Message    %SIM-3-QVLAN_PORT_SET_FAILED: Attempt to set port number [int] for the 
quarantine VLAN [chars] failed.  

Explanation    When a quarantine VLAN is assigned to an interface the system internally creates an interface .sys.quarantine-<port

Recommended Action    No action is required.

Error Message    %SIM-3-QVLAN_RECURSIVE: Quarantine VLAN cannot be configured on 
quarantine interface [chars].  

Explanation    This interface was automatically created by the system. Only limited configuration is supported on this interface.

Recommended Action    No action is required.

Error Message    %SIM-3-QVLAN_STATUS_DOWN: Quarantine VLAN for interface [chars] cannot 
be set because the interface is not fully configured.  

Explanation    Before the quarantine VLAN is configured on an interface, that interface must have its port and address information fully configured.

Recommended Action    No action is required.

Error Message    %SIM-3-ROUTE_ADD_FAIL: Failed to apply route configuration data;Route 
add failed.IP Address: [int].[int].[int].[int] 

Explanation    Failed to apply route configuration data;Route Add Failed!!

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-ROUTE_DEL_FAIL: Could not delete the route for the network 
[int].[int].[int].[int] 

Explanation    Could not delete the route for a network.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-SET_APMGR_ADDR_FAIL: Unable to set AP manager address. 
Subnet:[int].[int].[int].[int] Gateway:[int].[int].[int].[int] 

Explanation    Unable to set AP manager address.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-SET_APMGR_PORT_FAIL: Unable to set AP Manager interface port. 
Port # [dec] 

Explanation    Unable to set AP Manager interface port.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-SET_INTF_ADDR_FAIL: Unable to set service port interface 
address. Ip Address: [int].[int].[int].[int].Gateway: [int].[int].[int].[int] 

Explanation    Unable to set service port interface address.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-6-SET_P2P_BLOCK: Peer-to-Peer blocking check in forwarding path 
transitioned from [chars] to [chars]. 

Explanation    Peer to peer blocking check was enabled/disabled

Recommended Action    No action is required.

Error Message    %SIM-3-SET_VAP_INTF_FAIL: Unable to configure a Virtual Access Point 
Interface. Vap Id: [int] 

Explanation    Unable to configure a Virtual Access Point(VAP) Interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-SET_VLAN_ADDR_FAIL: Unable to set VLAN Interface Address. Ip 
Addr:[int].[int].[int].[int]. Gateway:[int].[int].[int].[int] 

Explanation    Unable to set VLAN Interface Address

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-7-START_CREATE_INTF: Started create interface. 
interfaceName:[chars], vlanId:[dec] 

Explanation    Started create Interface

Recommended Action    No action is required.

Error Message    %SIM-7-START_DEL_INTF: Started delete interface. 
InterfaceName:[chars] 

Explanation    Started delete interface

Recommended Action    No action is required.

Error Message    %SIM-7-STARTED_PORT_VLAN_SET: Started port and vlan set. interface 
'[chars]' priPort = [dec] backupPort = [dec] 

Explanation    Started port and vlan set

Recommended Action    No action is required.

Error Message    %SIM-7-STARTED_VLAN_SET: Started vlan set. intf name=[chars], 
vlanId:[dec], immediately:[dec] 

Explanation    Started vlan set.

Recommended Action    No action is required.

Error Message    %SIM-7-START_INTF_PORT_SET: Starting interface port set. interface 
'[chars]' priPort = [dec] 

Explanation    Starting interface port set.

Recommended Action    No action is required.

Error Message    %SIM-4-STP_DISABLE_FAIL: Failed to disable the STP sub-system for the 
switch. 

Explanation    Failed to disable the STP sub-system for the switch.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-STP_PORT_MODE_FAIL: Failed to set the port mode to off for STP. 

Explanation    Failed to set the port to off for STP.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-0-TIMER_CREATE_FAIL: Failed to create down timer for port [int] 

Explanation    Failed to create a software timer

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-0-TIMER_START_FAIL: Failed to start a software timer. 

Explanation    Failed to start a software timer.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-VLAN_ENTRY_FAIL: Failed to create VLAN interface [chars] 

Explanation    Failed to create VLAN interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-VLANID_NOT_CONF: A valid VLAN ID has to be configured first 
before the port set. Interface Name: [chars] 

Explanation    A valid VLAN ID has to be configured first before the port set

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-VLAN_INIT_FAIL: Error! Couldn't load interface configuration at 
initialization 

Explanation    Error! Couldn't load interface configuration at initialization

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-VLAN_INTFID_FAIL: Failed to assign Interface ID to Vlan - 
interface type: [dec]. 

Explanation    Failed to assign interface ID to vlan

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-VLAN_SAME_INTERFACE: Vlan Interface name [chars] already set. 
Cannot create the same interface 

Explanation    Vlan Interface already set. Cannot create the same interface

Recommended Action    No action is required.

Error Message    %SIM-3-VLAN_SAME_TAG: Interfaces configured with same Vlan Tag, but on 
different port - Not SupportedPort # [dec], Primary Port # [dec], Vlan Id [dec] 

Explanation    Interfaces configured with same Vlan Tag, but on different port - Not Supported

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-VLAN_UPDATE_FAIL: Failed to update the vlan port settings.Port 
# [int], vlan Id [int] 

Explanation    Failed to update the vlan port settings

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %SIM-3-WLAN_DISABLE_FAIL: Failed to disable WLAN [int] 

Explanation    Failed to disable WLAN.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/ . If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.