Cisco Wireless LAN Controller System Message Guide
MIRROR through PEM
Downloads: This chapterpdf (PDF - 482.0KB) The complete bookPDF (PDF - 15.88MB) | Feedback

MIRROR Messages

Table Of Contents

MIRROR Messages

MM Messages

MMC Messages

NIM Messages

NULL Messages

OSAPI Messages

PEM Messages


MIRROR Messages

This section contains Mirror Module (MIRROR) messages.

Error Message    %MIRROR-3-ADD_NODE_FAILED: Unable to add the mac address 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] into AVL tree. 

Explanation    Unable to add a node into AVL tree.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-AVL_DELETE_FAILED: Unable to delete the mac address 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] from AVL tree. 

Explanation    Unable to delete node from AVL tree.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-AVL_INIT_FAILED: Unable to create AVLs for Mirror module. 

Explanation    Unable to create AVLs for Mirror module.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-DISABLE_MIRRORPORT_FAILED: Could not disable the existing 
mirror port [dec]. 

Explanation    Could not disable the existing mirror port.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-ENABLE_MIRRORPORT_FAILED: Could not set the port [dec] as 
mirror port.Return code:[dec] 

Explanation    Could not set a port as mirror port.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-INVALID_PORT: Port [dec] is invalid. 

Explanation    Port is invalid.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-MEM_ALLOC_FAILED: Could not allocate memory for [chars]. 

Explanation    Could not allocate memory for heap.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-NODE_NOT_FOUND: Unable to add the mac address 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] into AVL tree. 

Explanation    Unable to find node in AVL tree.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-RETRIEVE_FILE_FAILED: Failed to retrieve the configuration 
file [chars]. 

Explanation    Failed to retrieve the mirror configuration file.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-SEM_CREATE_FAILED: Unable to create semaphore for Mirror 
module. 

Explanation    Unable to create semaphore for Mirror module.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-STORE_FILE_FAILED: Failed to store the configuration file 
[chars] into NV Memory. 

Explanation    Failed to store the mirror configuration file into NV Memory.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-TOGGLE_AP_FAILED: Could not toggle the AP [chars]'s mirror 
mode.[chars]. 

Explanation    Could not toggle the AP mirror mode.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-TOGGLE_MIRRORMODE_FAILED: Could not toggle mirror mode for 
the MAC address [hex]:[hex]:[hex]:[hex]:[hex]:[hex] to [chars] state 

Explanation    Could not toggle client mirroring.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-TYPE_NOT_MATCH: Given mac's 
([hex]:[hex]:[hex]:[hex]:[hex]:[hex]) type [dec] doesn't match with type [dec] 
found in the AVL tree. 

Explanation    Given node type doesn't match with the node type found in the AVL tree.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-UPDATE_FAP_AVL_FAILED: Could not update dynamic Foreign AP 
client to MAC AVL.Mac address is [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Could not update dynamic Foreign AP client to MAC AVL.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MIRROR-3-UPDATE_FAP_NPU_FAILED: Could not update Foreign AP client's 
mirror status in NPU.Mac Address is [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Could not update Foreign AP client's mirror status in NPU.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

MM Messages

This section contains mobility member (MM) messages.

Error Message    %MM-3-ACLNAM_GET_FAILED: Unable to get acl name for intfAclId [dec] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-ANCHOR_ADD_FAILED: Failed to add wlanId in heartbeat list: IP: 
[dec].[dec].[dec].[dec], WLAN ID: [dec]. 

Explanation    Internal system error

Recommended Action    Re configure mobility anchor list for this WLAN.

Error Message    %MM-3-ANCHOR_DEL_FAILD: Failed to delete wlan ID in heartbeat list: 
IP: [dec].[dec].[dec].[dec], wlanid: [dec]. 

Explanation    Internal system error

Recommended Action    Re configure mobility anchor list for this WLAN.

Error Message    %MM-2-ANCHOR_NOT_DEFINED: Auto anchor required but no anchors defined. 
Wlan-Id:[dec],SSID:[chars]. 

Explanation    Auto anchor required but no anchors defined on the WLAN.

Recommended Action    If this message occurs, it implies that anchors need to be defined for the reported WLAN.

Error Message    %MM-6-ANCHOR_READY: WLAN [dec] is ready to service clients as an 
anchor, [int].[int].[int].[int] has come up  

Explanation    WLAN is ready to service clients as an anchor.

Recommended Action    No action is required.

Error Message    %MM-1-ANCHORS_DOWN:  All Export-Anchors are down on WLAN [dec]  

Explanation    All Export-Anchors are down on WLAN

Recommended Action    If this message occurs, it implies that there is loss of network connectivity between the WLC and the export anchors for this WLAN.It is recommended that the network and the status of the anchors be debugged for connectivity issues.

Error Message    %MM-1-ANCHOR_SEND_FAILED: Unable to send Anchor Close/Transfer message 
to [dec].[dec].[dec].[dec] due to memory allocation failure. 

Explanation    The system may be running low on memory.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-1-ANCHOR_UNAVAILABLE: All export anchors are down. Cannot anchor 
the client.[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    No export anchors are up to anchor the client.

Recommended Action    If this message occurs, it implies that there may be loss of network connectivity between the WLC and the export anchors for this WLAN.It is recommended that the network and the status of the anchors be debugged for connectivity issues.

Error Message    %MM-1-APENTRY_ADD_FAILED: Unable to create ap-list entry for AP 
[hex]:[hex][hex]:[hex]:[hex][hex]  

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-APENTRY_DEL_FAILED: Could not delete an AP from the AP list. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-BUFF_ALLOC_FAILED: Could not allocate a system buffer. [chars]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-BUFF_DEALLOC_FAILED: Could not deallocate a system buffer. 
[chars]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-6-CCKM_CACHE_CREATE:  Creating CCKM cache on receiving message 
from mobility peer. 

Explanation    Internal system information

Recommended Action    No action is required.

Error Message    %MM-6-CCKM_NSK_SEND:  Sending CCKM NSK information in mobility group  

Explanation    Internal system information

Recommended Action    No action is required.

Error Message    MM-3-CLIENT_ADD_MSG_SEND_ERROR: Unable to send heartbeat list client 
add message to mobility task 

Explanation    An internal system error occurred.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-CLIENT_DELETE_MSG_SEND_ERROR: Unable to send heartbeat list 
client delete message to mobility task 

Explanation    An internal system error occurred.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-1-CLIENT_SHUNNED: Adding client 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] to exclusion list as a result of an IDS shun 
event for [int].[int].[int].[int] 

Explanation    Adding a client to exclusion list as a result of an IDS shun event.

Recommended Action    No action is required.

Error Message    %MM-3-EXPORTANCHOR_REQPROC_FAILED: Anchor Export Request from 
controller (IP: [dec].[dec].[dec].[dec]) ignored. WLAN:[dec]. ClientSec:[hex], 
WlanSec:[hex]. [chars]. 

Explanation    Anchor Export Request from controller is ignored.

Recommended Action    This message implies that the WLAN configuration needs change to alleviate the reported error.

Error Message    %MM-1-EXPORT_FOREIGN_DOWN: Export FOREIGN [int].[int].[int].[int] is 
detected as DOWN. Status:[dec].Cleaning up client entries. 

Explanation    Export FOREIGN is detected as DOWN. Cleaning up client entries.

Recommended Action    This is a mobility failover event that has occurred due to loss of connectivity between this WLC and one of its mobility peers. Please debug your network for connectivity issues and check the status of the down mobility peer.

Error Message    %MM-3-EXPORT_MSG_SEND_ERROR1: Unable to send WiredClientAnchorExport 
message to mobility task 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-EXPORT_MSG_SEND_ERROR2: Failed to send AnchorExport message, 
mobile [hex]:[hex]:[hex]:[hex]:[hex]:[hex] not found 

Explanation    Foreign did not send mobility message because mobile was not found

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-1-GUEST_LAN_ANCHORS_DOWN:  All Export-Anchors are down on Guest 
LAN [dec]  

Explanation    All Export-Anchors are down on Guest LAN

Recommended Action    If this message occurs, it implies that there is loss of network connectivity between the WLC and the export anchors for this guest LAN.It is recommended that the network and the status of the anchors be debugged for connectivity issues.

Error Message    %MM-4-HB_MEMBER_ADD_ERROR: Error adding Mobility member to heartbeat 
list (MAC:[hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP: [dec].[dec].[dec].[dec]). 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-4-HB_MEMBER_DELETE_ERROR: Error deleting Mobility member from 
heartbeat list (MAC:[hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP: 
[dec].[dec].[dec].[dec]). 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-6-HEARTBEAT_LIST_MEMBER_UPDATED: Updating Mobility member IP in 
heartbeat list(MAC: [hex]:[hex]:[hex]:[hex]:[hex]:[hex], oldIP: 
[dec].[dec].[dec].[dec], newIP: [dec].[dec].[dec].[dec]). 

Explanation    Internal system information

Recommended Action    No action is required.

Error Message    %MM-4-HEARTBEAT_LIST_MEMBER_UPDATE_ERROR: Error updating Mobility 
member IP in heartbeat list(MAC: [hex]:[hex]:[hex]:[hex]:[hex]:[hex], oldIP: 
[dec].[dec].[dec].[dec], newIP: [dec].[dec].[dec].[dec]). 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-2-INIT_FAILED: Error while initializing mobility manager: [chars]. 

Explanation    Error while initializing mobility manager.

Recommended Action    If this error is seen, it is recommended that the controller's mobility configuration be redone as it may have been lost.

Error Message    %MM-3-INTFCHANGE_REGISTER_FAILED: Failed to register callback for 
interface changes 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-INVALID_APLISTUPD_RECVD: Received invalid ap-list-update from 
[int].[int].[int].[int]. Entries:[dec], Expected:[dec]. [chars]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-INVALID_CIDSUPD_RECV: Received invalid cids-update from 
[int].[int].[int].[int]. Entries:[dec], Expected:[dec]. [chars]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-INVALID_NONCE_RECVD: Received an invalid Nonce-update from 
[int].[int].[int].[int]. [chars]. 

Explanation    An internal system error occurred.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-INVALID_PKT_RECVD: Received an invalid packet from 
[dec].[dec].[dec].[dec]. Source member:[dec].[dec].[dec].[dec]. [chars]. 

Explanation    Internal system error

Recommended Action    Please check mobility configuration to see if it needs correction.

Error Message    %MM-3-INVALID_PMKDEL_RECVD: Received PMK-delete from 
[int].[int].[int].[int] with no StationAddress TLV. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-INVALID_PMKUPD_RECVD: Received an invalid PMK-update from 
[int].[int].[int].[int]. [chars]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-4-INVALID_ROAMRESP_RECVD: Received Roam response from 
[int].[int].[int].[int] with no PMK-R1 TLV 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-INVALID_WEPDEL_RECVD: Received WEP-Key-delete from 
[int].[int].[int].[int] with no Station Address TLV 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-INVALID_WEPUPD_RECVD: Received an invalid WEP-Key-update from 
[int].[int].[int].[int]. [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-1-IPSECPAYLOAD_BUILD_FAILED: Unable to build IPSec export data. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-0-LISTEN_TASK_EXITED: mmListen task did not receive a task control 
block --exiting 

Explanation    Internal system error

Recommended Action    The mobility services failed to start correctly. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-LOCMARK_FAILED: Unable to mark the mobility location of client 
to unknown. 

Explanation    Unable to mark the mobility location of client to unknown.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-MEM_ALLOC_ERROR1: No memory to send WiredClientAnchorExport 
message to mobility task for WGB [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    The system may be running low on memory.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-6-MEMBER_ADDED: Adding Mobility member (Index:[dec], 
MAC:[hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP: [dec].[dec].[dec].[dec]) in [chars]. 

Explanation    Internal system information

Recommended Action    No action is required.

Error Message    %MM-3-MEMBER_ADD_FAILED: Could not add Mobility Member. Reason: 
[chars], Member-Count:[dec],MAC: [hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP: 
[dec].[dec].[dec].[dec]. 

Explanation    Could not add Mobility Member for the given reason.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-6-MEMBER_DELETED: Deleting Mobility member (Index:[dec], 
MAC:[hex]:[hex]:[hex]:[hex]:[hex]:[hex]) from [chars]. 

Explanation    Internal system information

Recommended Action    No action is required.

Error Message    %MM-3-MEMBER_DEL_FAILED: Could not delete Mobility Member. 
Member=Count:[dec], MAC:[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Mobility Member deletion from the list failed.

Recommended Action    Please check if the mobility member to be deleted exists.

Error Message    %MM-4-MEMBER_DOWN: [chars] path to mobility member 
[int].[int].[int].[int] is DOWN. 

Explanation    A path to mobility member is DOWN.

Recommended Action    If this message occurs, it implies that there is loss of network connectivity between the WLC and one of its mobility peers.It is recommended that the network and the status of the peers be debugged for connectivity issues.

Error Message    %MM-6-MEMBER_UP: [chars] path to mobility member 
[int].[int].[int].[int] is UP. 

Explanation    A path to mobility member is UP.

Recommended Action    No action is required.

Error Message    %MM-6-MEMBER_UPDATED: Updating Mobility member (Index:[dec], 
MAC:[hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP: [dec].[dec].[dec].[dec]) in [chars]. 

Explanation    Internal system information

Recommended Action    No action is required.

Error Message    %MM-3-MM_ACL: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-0-MOBILITY_TASK_EXITED: mmMobility task did not receive a task 
control block --exiting 

Explanation    Internal system error

Recommended Action    The mobility services failed to start correctly. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    MM-0-MOBILITY_TASK_FAILED_TO_START: [chars] task could not be started. 
The system will be rebooted  

Explanation    Internal system error

Recommended Action    The mobility services failed to start correctly. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-1-MOBILITYUSER_STATECREATE_FAILED: Unable to create mobility state 
for user [chars]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-MSG_PROC_FAILED: Unable to process the received mobility 
message. [chars]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-0-MULTICAST_GROUP_IP_SET_ERROR: Error in [chars] while setting 
local moblity group multicast IP Address [dec].[dec].[dec].[dec]. Please disable 
mobility multicast-mode if this error continues. 

Explanation    Mobility is unable to use multicast for messaging.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-MULTICAST_GROUP_SEND_ERROR: Unable to send multicast mobility 
message. 

Explanation    Mobility is unable to use multicast for messaging.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-NO_APLIST_TLV: Received invalid ap-list-update from 
[int].[int].[int].[int] with no ap-list TLV. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-PEER_PING_FAILED: Mobility ping to [int].[int].[int].[int] 
rejected. [chars]. 

Explanation    Mobility ping rejected.

Recommended Action    Please check the mping command issued.

Error Message    %MM-4-PING_FAILED: [chars] ping request to [int].[int].[int].[int] 
failed rc=[dec] 

Explanation    A ping request is failed.

Recommended Action    If this message occurs repetitively, it implies that there may be loss of network connectivity between the WLC and another mobility list member.It is recommended that the network and the status of the member be debugged for connectivity issues.

Error Message    %MM-6-PING_RECEIVER_ENTRY_DELETED: Deleted ping receiver 
entry([dec].[dec].[dec].[dec]) from hearbeat list for WLAN([dec]). 

Explanation    Internal system information

Recommended Action    No action is required.

Error Message    %MM-3-PING_RESPONSE_DROPPED: Drop mobility ping reply from 
[int].[int].[int].[int]. Expected reply from [int].[int].[int].[int]. [chars]. 

Explanation    Mobility ping response dropped.

Recommended Action    No action is required.

Error Message    %MM-3-PING_SEND_FAILED: Failed to send a ping [chars] packet to 
[int].[int].[int].[int]. 

Explanation    Failed to send a ping.

Recommended Action    Please check mobility configuration to see if it needs correction. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-4-PKT_DROPPED: Mobility packet dropped. [chars]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.e

Error Message    %MM-4-PMKCACHE_ADD_FAILED: Failed to create PMK/CCKM cache entry for 
station [hex]:[hex]:[hex]:[hex]:[hex]:[hex] with update from controller 
[int].[int].[int].[int] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-4-PMKCACHE_DEL_FAILED: Failed to delete PMK cache entry for 
station [hex]:[hex]:[hex]:[hex]:[hex]:[hex] with request from controller 
[int].[int].[int].[int] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-SEND_FAILED: Unable to send [chars] to [dec].[dec].[dec].[dec] 

Explanation    Unable to send a mobility packet.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-SOCK_OPER_FAILED: Failed to [chars] a socket. 

Explanation    A socket operation is failed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-6-SOCK_SET_ADDRESS_OPTION: Setting membership for interface IP 
[dec].[dec].[dec].[dec] and multicast group [dec].[dec].[dec].[dec] on the 
mobility sockets. 

Explanation    Multicast group membership was set on the socket.

Recommended Action    No action is required.

Error Message    %MM-3-SOCK_SET_ADDRESS_OPTION_FAILED: Failed to [chars] address 
[dec].[dec].[dec].[dec] to the socket options. 

Explanation    A socket operation has failed. Multicast mode will not work for mobility.

Recommended Action    Set the local group multicast address again. If this same message appears, disable multicast mode for mobility. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-1-SSHRULE_CREATE_FAILED: Failed to [chars] the SSH Rule for 
[int].[int].[int].[int]. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-1-USER_NOT_ALLOWED: Unable to allow user [chars] into the system. 
[chars]. 

Explanation    Unable to allow the user into the system for the reported reason.

Recommended Action    No action is required.

Error Message    %MM-4-WEPCACHE_ADD_FAILED: Failed to create WEP-Key cache entry for 
station [hex]:[hex]:[hex]:[hex]:[hex]:[hex] with update from controller 
[int].[int].[int].[int] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-4-WEPCACHE_DEL_FAILED: Failed to delete WEP cache entry for 
station [hex]:[hex]:[hex]:[hex]:[hex]:[hex] with request from controller 
[int].[int].[int].[int] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MM-3-WGB_ANCHOREXP: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

MMC Messages

This section contains Mobility Management Connection (MMC) messages.

Error Message    %MMC-2-BUFFPOOL_ALLOCATE_FAILED: Failed to allocate a pool of size 
[dec] bytes from a buffer pool(Id=[dec]). 

Explanation    The MMC module has failed to allocate some memory required by it. The traceback along with this message will suggest why it was needed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MMC-3-GMACREG_WRITE_FAILED: Setting Network processor register 
failed. This could be temporary problem 

Explanation    The MMC module has failed to set the control register of the Network processor. This can be a temporary problem.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MMC-6-LINKSTATUS_CHECK_FAILED: Checking the link status of a 
particular port failed. 

Explanation    The MMC module has failed to read the link status register of the Network processor.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MMC-0-NPU_INVALID_FRAME: NPU Frame block invalid 

Explanation    The MMC module has received an invalid frame from the Network Processor.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MMC-6-NPUMSG_READ_FAILED: Reading CPU messages from NPU failed. 

Explanation    The MMC module has failed to read the message queue object which contains any message sent by the Network processor.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %MMC-0-NPU_OPER_FAILED: NPU Operational verification failed. 

Explanation    The MMC module has failed to verify whether the Network Processor is operational or not.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

NIM Messages

This section contains Networks-in-Motion (NIM) messages.

Error Message    %NIM-4-ADDR_TYPE_INVALID: Address type [dec] is not valid for 
interface [dec]. 

Explanation    Address type is not valid. It is neither Burned in Address nor Locally Administered Address

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-ADMIN_STATE_INVALID: Admin State [dec] is not valid for 
interface [dec]. 

Explanation    Admin State is not valid.The state is neither ENABLE nor DISABLE

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-CANT_DISABLE_MCAST: Cannot disable multicast state for 
interface [int] when LAG is enabled 

Explanation    Cannot disable multicast state when LAG is enabled

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-CHECK_SUM_ERR: Checksum Error on config file [chars]. 

Explanation    Checksum Error on the config file

Recommended Action    No action is required.

Error Message    %NIM-3-COMPONENT_ALREADY_REGISTERED: Component [dec] already 
registered. 

Explanation    Component already registered. A component which is already registered with a state change function is trying to register again

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-CREAT_CPUINTF_FAIL: CPU INTF Create error: Ran out of CPU 
Interface internal numbers. 

Explanation    NIM Create error: Ran out of CPU Interface internal numbers.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-CREAT_LAGINTF_FAIL: LAG interface Create error:Ran out of LAG 
Interface internal numbers. 

Explanation    LAG interface Create error:Ran out of LAG Interface internal numbers.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-CREAT_LOGICALINTF_FAIL: Logical interface create error:Ran out 
of Logical Interface internal numbers. 

Explanation    Logical interface create error:Ran out of Logical Interface internal numbers.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-CREAT_PHYINTF_FAIL: PHY interface Create error: Ran out of 
Physical Interface internal numbers. 

Explanation    PHY interface Create error: Ran out of Physical Interface internal numbers.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-0-CREAT_TASK_FAIL: Failed to create the task [chars] 

Explanation    Failed to create the task

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-CREAT_VLANINTF_FAIL: Logical Vlan interface Create error:Ran 
out of Logical Interface internal numbers. 

Explanation    Logical Vlan interface Create error:Ran out of Logical Interface internal numbers.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-FS_WRITE_FAIL: Writing data to the config file [chars] failed. 

Explanation    Writing data to the user config file failed

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-INIT_TASK_FAIL: Task initialization failure. Waiting on handle 
[chars] failed 

Explanation    Task initializing failed for NIM component.Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-INVALID_CREAT_REQUEST: Invalid [chars] Create Request. 

Explanation    Invalid Interface Create Request.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-6-LAA_ADDR_INVALID: Locally administered address is not valid for 
interface [dec]. 

Explanation    Locally administered address is not valid. LSB of first byte not zero.

Recommended Action    No action is required.

Error Message    %NIM-4-LAG_IN_TRANSITION: LAG in transition. switch reboot DUE..!!! 

Explanation    LAG in transition. switch reboot DUE..!!!

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-LOAD_PORTINFO_FAIL: Loading port info for port number [dec] 
failed. Ran out of Physical Interface internal numbers. 

Explanation    Loading Multicast appliance mode port configuration failed. Ran out of Physical Interface internal numbers

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-4-MCAST_NOT_SET: Multicast appliance flag not set for interface 
[int]([int],[int],[int]) when LAG enabled. 

Explanation    Multicast appliance flag not set,when LAG enabled.

Recommended Action    No action is required.

Error Message    %NIM-6-MCAST_STATE_CHANGED: LAG Enabled - changed multicast state of 
interface [int] to ENABLED 

Explanation    LAG Enabled - changed multicast state to ENABLED

Recommended Action    No action is required.

Error Message    %NIM-3-MCAST_STATE_UNKNOWN: interface [int] has invalid 
mcastApplianceState [dec] 

Explanation    The multicast appliance state is invalid

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-0-MSGQ_CREATE_FAIL: Unable to create msg queue for nimTask. 

Explanation    Unable to create msg queue for nimTask.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-MSGQ_SEND_FAIL: Failed to send message to the Queue [chars] 

Explanation    Failed to send the interface change notification message to the message queue

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-4-NAME_TYPE_INVALID: Name Type [dec] is not valid for interface 
[dec]. 

Explanation    Interface Name Type is not valid.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-4-POE_STATE_INVALID: PoE State [dec] is not valid for the 
interface [dec]. 

Explanation    PoE State is not valid.The state is neither ENABLE nor DISABLE

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-PORTS_ALREADY_SET: All ports have been already configured 

Explanation    All ports have been already configured with an internal interface number. could not find a port to set multicast mode

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-PORT_TYPE_UNKNOWN: Unsupported port type [dec] to find for 
interface [dec]. 

Explanation    Unsupported port type for the specified interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-PROBED_INTF_NOTEXIST: Probed interface [dec] not present. 

Explanation    Probed interface not present.Mirroring failed

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-PROBING_INTF_NOTEXIST: Probing interface [dec] not present. 

Explanation    Probing interface not present.Mirroring failed

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-REGID_INVALID: Registrar ID [dec] grater than the last 
component id 

Explanation    Registrar ID invalid.It is greater than the last valid component's ID.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-0-REGISTRY_GET_FAIL: Unable to pull value from the registry for 
the key [chars] 

Explanation    Unable to pull value from the registry

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-SET_AUTONEG_FAIL: Error in setting the AutoNeg status for the 
interface with internal interface number [dec]. 

Explanation    Error while setting the status for Auto Negotiation.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-SET_INTFSPEED_FAIL: Error while setting the speed mode for the 
interface with internal interface number [dec]. 

Explanation    Error in setting the speed mode for the interface. The speed and the interface type are not compatible

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-SET_MCASTSTATE_FAIL: Error while setting MCAST appliance state 
for the interface with internal interface number [dec]. 

Explanation    Error while setting MCAST appliance state for an interface

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-SET_MTUSIZE_FAIL: Error while setting MTU size for the 
interface with the internal interface number [dec]. 

Explanation    Error while setting MTU size for the interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-6-STACKINTF_NOT_SUPPORTED: Creating Stack Interface currently not 
supported. 

Explanation    Creating Stack Interface currently not supported.

Recommended Action    No action is required.

Error Message    %NIM-6-SW_VER_ERR: Software Version Error on config file [chars]. 

Explanation    Software Version Error on config file.

Recommended Action    No action is required.

Error Message    %NIM-3-SYSINTF_TYPE_UNKNOWN: Unknown system interface type [dec]. 

Explanation    Unknown system interface type.Could not find next valid interface's internal interface number.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-4-TRAP_STATE_INVALID: Trap State [dec] is not valid for interface 
[dec]. 

Explanation    Trap State is not valid. It is neither ENABLE or DISABLE

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-UNKNOWN_INTF_TYPE: Unknown Interface type requested. 

Explanation    Create interface error. Unknown Interface type requested.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-USP_PORT_ERR: Error in USP and/or port registry data. 

Explanation    Error in USP and/or port registry data.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %NIM-3-USP_SLOT_ERR: Error in USP and/or SYSTEM_SLOTS registry data. 

Explanation    Error in USP and/or SYSTEM_SLOTS registry data.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

NULL Messages

This section contains NULL subsystem (NULL) messages.

Error Message    %NULL-0-SOCKET_CREATE_FAILED: Socket creation failed 

Explanation    The NULL module has failed to create a particular socket. The traceback along with this message will suggest as to which socket it was.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

OSAPI Messages

This section contains operating system API (OSAPI) messages.

Error Message    %OSAPI-5-CLEAN_TASK: Reaper cleaning up exited task '[chars]' 
([address]) 

Explanation    Reaper cleaning up exited task

Recommended Action    No action is required.

Error Message    OSAPI-3-CLOSE_FAILED: Failed to close file  

Explanation    System was unable to close a file.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-COLLECT_TASK_METRICS_FAILED: Unable to gather task metrics. 
[chars]. 

Explanation    Unable to gather task metrics.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-CPU_OVERLOAD: Warning! Task [dec] ([chars]) is taking [dec]% 
([dec]% user [dec]%system)of the cpu!. 

Explanation    Warning! A Task is overloading the CPU. Try Killing the Task!

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-5-FILE_CLOSE_FAILED: Failed to close the file descriptor: 
[dec]. 

Explanation    The system could not close a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-FILE_CREATE_FAILED: Failed to create the file : [chars]. 
[chars]. 

Explanation    The system could not create a file or directory. There may be several reasons behind it, including that the system has run out of disk space.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-5-FILE_DEL_FAILED: Failed to delete the file : [chars]. 
[chars]. 

Explanation    The system could not delete a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-6-FILE_DOES_NOT_EXIST: File : [chars] does not exist. 

Explanation    The system could not find the file or directory. There may be several reasons behind it, including that certain functionality has never been configured on the system.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-FILE_MOVE_FAILED: Failed to move the file [chars] to [chars]. 

Explanation    The system could not move or rename a file or directory. There may be several reasons behind it, including that the source path provided does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-FILE_OPEN_FAILED: Failed to open the file : [chars]. 

Explanation    The system could not open a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-5-FILE_READ_FAILED: Failed to read [dec] bytes from the file : 
[chars] (FileDesc:[dec]). [chars]. 

Explanation    The system could not read from a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-5-FILE_READNOCLOSE_FAILED: Failed to read [dec] bytes 
(FileDesc:[dec]). [chars]. 

Explanation    The system could not read from a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-FILE_TRANSFER_ABORTED: Aborting file transfer. [chars]. 

Explanation    Aborting file transfer.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-FILE_WRITE_FAILED: Failed to write [dec] bytes to the file : 
[chars] (FileDesc:[dec]). [chars]. 

Explanation    The system could not write to a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-FILE_WRITENOCLOSE_FAILED: Failed to write [dec] bytes 
(FileDesc:[dec]). [chars]. 

Explanation    The system could not write to a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-GW_ADD_FAILED: Unable to add the gateway [chars]. System 
command returned failure. Error code:[dec] 

Explanation    Unable to add a gateway. System command returned failure.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-INTF_IOCTL_FAILED: The I/O control operation ([chars]) has 
failed on the interface [chars].IpAddr:[int].[int].[int].[int] Errorcode:[dec] 

Explanation    The I/O control operation has failed on the interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-INVALID_PING_RESPONSE: Ping response from 
[int].[int].[int].[int] is invalid. [chars]. 

Explanation    Ping response is invalid.

Recommended Action    This is a debug message only. No action is required.

Error Message    %OSAPI-0-INVALID_TIMERCB: Invalid timer control block. TcbPtr=[hex]. 

Explanation    Invalid timer control block, a software timer object failed

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-INVALID_TIMER_HANDLE: Task is using invalid timer handle 
[int]/[int] 

Explanation    Task is using invalid timer handle.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    OSAPI-3-IOCTL_FAILED: ioctl ([chars]) failed for interface [chars].  

Explanation    System was unable to complete the specified ioctl operation.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-KTHREAD_STRUCT_ALLOC_FAILED: We failed to create a struct for 
/proc/[chars]/status 

Explanation    Failed to create structure for storing Kthread information.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-KTHREAD_TABLE_FULL:  Need a bigger osapi_kthread_tbl to store 
kthread [chars] pid=[dec]. 

Explanation    Need a bigger osapi_kthread_tbl to store a kthread.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-LINK_ERROR: Error condition detected on link [chars] (rxp 
[int] rxe [int]; previously rxp [int] rxe [int]  

Explanation    Link error detected on the specified link.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-MEM_ALLOC_FAILED: Failed to allocate memory for [dec] bytes. 

Explanation    Failed to allocate some memory. System might be out of buffers. This may be temporary

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-MSGQ_CREATE_FAILED: Failed to create the message queue 
object: [chars]. [chars]. 

Explanation    Failed to create a message queue object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-5-MSGQ_DEL_FAILED: Failed to delete the message queue object: 
[chars]. [chars]. 

Explanation    Failed to delete a message queue object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-MSGQ_RECV_FAILED: Failed to receive a message from the 
message queue object: [chars]. [chars]. 

Explanation    Failed to receive a message from a message queue object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-MSGQ_SEND_FAILED: Failed to send a message to the message 
queue object: [chars]. [chars]. 

Explanation    Failed to send a message to a message queue object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-MUTEX_CREATE_FAILED: Failed to create a mutual exclusion 
object. [chars]. 

Explanation    Failed to create a mutual exclusion object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-5-MUTEX_DEL_FAILED: Failed to delete a mutual exclusion object. 
[chars]. 

Explanation    Failed to delete a mutual exclusion object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-MUTEX_LOCK_FAILED: Failed to acquire a mutual exclusion 
object. [chars]. 

Explanation    Failed to acquire a mutual exclusion object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-1-MUTEX_PRIO_CLEAR: == Unlock assert == ([chars]) prio=[dec] 
root=[hex] word[[dec]]=[hex].  

Explanation    Mutex clear lock failure.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-1-MUTEX_PRIO_SET: ** Lock assert ** ([chars]) prio=[dec] 
root=[hex] [chars]  

Explanation    Mutex lock priority violation.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-1-MUTEX_PRIO_SET2: ** Lock assert ** ([chars]) prio=[dec] 
root=[hex] word[[dec]]=[hex].  

Explanation    Mutex lock priority violation 2.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-5-MUTEX_UNLOCK_FAILED: Failed to release a mutual exclusion 
object. [chars]. 

Explanation    Failed to release a mutual exclusion object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-OPEN_FAILED: Failed to open file [chars]  

Explanation    System was unable to open a file with the given name.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-PATH_BUILD_FAILED: Failed to build the path string for 
[chars] 

Explanation    Failed to build a path string.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-PING_OPER_FAILED: Unable to start ICMP ping to host [chars]. 
[chars] 

Explanation    Unable to start ICMP ping to host.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-RAD_SW_UPGRADE: System has been upgrading Radio SW for more 
than 30 minutes.  

Explanation    APs have been downloading software for the last 30 minutes. Either the network is congested or there is a mismatch between the AP image and the Controller image.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-REAPER_START_FAILED: Unable to start the Osapi Reaper. 
[chars]. 

Explanation    Unable to start an Osapi Reaper.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-REAPWATCHER_START_FAILED: Unable to start the Osapi Reaper 
Watcher. [chars]. 

Explanation    Unable to start an Osapi Reaper Watcher.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-ROUTE_ADD_FAILED: Unable to add the route (Dest:[chars], 
NetMask:[chars], NextHop:[chars]). System command returned failure. 
Errorcode:[dec] 

Explanation    Unable to add a route. System command returned failure.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-ROUTE_DEL_FAILED: Unable to delete the route (Dest:[chars], 
NetMask:[chars], NextHop:[chars]). System command returned failure. 
Errorcode:[dec] 

Explanation    Unable to delete a route. System command returned failure.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-ROUTE_INFO_GET_FAILED: Unable to retrieve routing information 

Explanation    Unable to retrieve routing information.Unable to access /proc/net/route

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-SOCKET_FAILED: Failed to open socket.  

Explanation    System was unable to open a socket.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-SOCK_OPER_FAILED: The [chars] operation has failed on the 
socket descriptor [dec]. Errorcode:[dec] 

Explanation    An operation has failed on a socket descriptor.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Recommended Action   

Error Message    %OSAPI-3-SYSINFO_FAILED: The system API sysinfo() returned failure. 
Error: [chars]. 

Explanation    The system API returned a failure.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-TASK_ADD_LOCKED: Exceeded maximum task count [int] (max 
[int]) 

Explanation    Exceeded maximum number of tasks that can be created

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-TASK_CREATE_FAILED: Failed to create the task object: 
[chars]. [chars]. 

Explanation    Failed to create a task object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-TASK_GETTIME_FAILED: Failed to retrieve statistics 
(/proc/<pid>/stats) for task '[chars]' 

Explanation    Failed to retrieve statistics (/proc/<pid>/stats) for a task

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-TASK_HUNG: Error! Hung task detected ([chars])! (user [dec]% 
system [dec]%)Reset!. 

Explanation    Error! Hung task detected. Reset!.Try Killing the Task!

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-TASK_INVALID_ADDRESS: Invalid task [address] ([address] < msg 
< [address]) (1) 

Explanation    Detected a possible corrupted task

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-TASKLIST_CORRUPTED: Task list corruption detected!!!. 

Explanation    Task list corruption detected.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-TASK_RMV_LOCKED: Failed to delete a task 
osapiTaskFreeList.head [address], count [int] 

Explanation    Failed to delete a task

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-TASK_SET_TICKLE: Task [chars] requesting [dec] second timer. 
Minimum is 20. Setting to 20. 

Explanation    Requested timer less than minimum time allowed. Minimum is 20. Setting to 20.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-TIMERCB_ALLOC_FAILED: Unable to allocate timer control block. 

Explanation    Unable to allocate memory for a software timer control block.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-TIMERCB_FREELIST_CORRUPTED: Timer control block free list is 
corrupted. Head=[hex],Count=[dec],Mempool Size=[dec]. 

Explanation    Timer control block free list is corrupted.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-0-TIMER_CREATE_FAILED: Failed to create a timer. 

Explanation    The system could not create a software timer object.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-TIMERTCB_NOT_ALLOCATED: Timer [int]/[int] ('[chars]') 
already destroyed. 

Explanation    A software timer object is already destroyed and cannot be used

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-TIMERTCB_REALLOCATED: Timer [int]/[int] ('[chars]') found to 
be destroyed/reallocated. 

Explanation    Timer found to be destroyed/reallocated.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-4-TIME_SHIFT_DETECTED: Detected [chars] time shift. Last: 
[dec].[dec]. --> Now:[dec].[dec]. 

Explanation    Detected a time shift.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

PEM Messages

This section contains Power Entry Module (PEM) messages.

Error Message    %PEM-1-ADDNPURULE1: Unable to push temporary Fast Path rule for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] on AP [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-ADDNPURULE2: Unable to plumb temporary rule for 
mobile[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-ADDNPURULE3: [chars] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-ADDSTA: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-ADDVPN: Unable to create IPsec rule for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex]. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-ADDVPN2: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-2-ADDVPN3: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-4-ADDVPN4: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-ADDWEBRULE1: Unable to add web rule for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] on AP [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-ADDWEBRULE2: Unable to create web rule for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex]. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-AEPIINIT: Bypassing AEPI process for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    AEPI is not enabled, hence bypassed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-APPLYPOL: pemLogInWebAuthUser: Failed to apply RADIUS policy. 

Explanation    AAA override is not enabled or there is a WLAN misconfiguration.

Recommended Action    Check the WLAN configuration.

Error Message    %PEM-3-BADWLANID1: Ignoring zero WLAN ID on AP 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    No action is required.

Error Message    %PEM-3-BADWLANID2: PEM state [dec], APF state [dec], MM state [dec] 
for mobile [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    No action is required.

Error Message    %PEM-3-CFGSAVE: Error on call to osapiFsWrite routine on config file 
[chars]. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-4-CHANGENACSTATE: Client [hex]:[hex]:[hex]:[hex]:[hex]:[hex] not 
found while changing NAC state   

Explanation    Chnaging NAC state for client failed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-0-CREATETASK: Failed to create PEM receive task. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-DELIKE: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-DELMMVPN: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-DELMSRULE1: Unable to delete policy rule [dec] for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    No action is required.

Error Message    %PEM-1-DELMSRULE2: Unable to delete policy rule for 
mobile[hex]:[hex]:[hex]:[hex]:[hex]:[hex]  

Explanation    Internal system error

Recommended Action    No action is required.

Error Message    %PEM-3-DELMSRULE3: [chars] 

Explanation    Internal system error

Recommended Action    No action is required.

Error Message    %PEM-3-DELSTA: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-DELSTA2: [chars] 

Explanation    We attempted to delete a client that does not exist. Perhaps it has already been deleted.

Recommended Action    No action is required.

Error Message    %PEM-2-DELVPN1: [chars] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-DELVPN2: [chars] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-4-DELVPN3: [chars] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-2-DELVPN4: [chars] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-DOT1XINIT1: Unable to initialize 802.1X for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] on AP [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-DOT1XINIT2: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-GETPOL: Unable to retrieve encrypt policy for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Unable to retrieve encryption policy for mobile

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-GLOBALSTAT_GET_FAILED: Unable to get the web-customizations 
global status for WLAN ID [dec]. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-6-GUESTIN: Guest user logged in with user account ([chars]) MAC 
address [hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP address [int].[int].[int].[int]. 

Explanation    Guest user logged in.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-6-GUESTOUT: Guest user logged out with user account ([chars]) MAC 
address [hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP address [int].[int].[int].[int]. 

Explanation    Guest user logged out.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-IMPORTSA: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-INVRULE: [chars] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-MGMTINTF: Can not get management interface. 

Explanation    The management interface cannot be found. It needs to be configured.

Recommended Action    Configure the management interface.

Error Message    %PEM-3-MSGQ: pemSysInit: couldn't create PEM message queue. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-MSGTAG050: [chars]: Unable to register L2TP session 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-NOOVERRIDE: Failed to apply RADIUS over-ride policy for station 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    AAA over-ride is disabled or the WLAN is misconfigured.

Recommended Action    Check your WLAN configuration.

Error Message    %PEM-0-NOQ: PEM: no message queue, exiting. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-4-NORCV: PEMRECV: MessageReceive() failed. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-PLUMB: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-PLUMBIP: Unable to add IP address learning SCB to NPU for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-PORTCHANGE: simMsPortChange Error in queuing pem message 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-REDIRRULE: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-SERVTYPE: Rejecting web-auth login for user '[chars]' with 
invalid Service-Type [dec] 

Explanation    Invalid AAA service type

Recommended Action    No action is required.

Error Message    %PEM-1-SETNAME: Unable to allow user [chars] into the system - perhaps 
the user is already logged onto the system? 

Explanation    This user name might have reached its maximum number of allowed sessions. This number is configurable.

Recommended Action    Check the configured number of allowed sessions for this user. It may be 0, or the user has already reached the maximum number of allowed sessions. If the latter, disconnect one of the sessions.

Error Message    %PEM-1-SNIFFAP: Unable to add sniffer AP fast path rule for AP 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    No action is required.

Error Message    %PEM-1-SPAMADDSTA: Unable to create SPAM Mobile State. 

Explanation    Internal system error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-4-TXIAPPTBL: Unable to send IAPP AssocTableReq for mobile 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Internal system error

Recommended Action    No action is required.

Error Message    %PEM-3-TXXID: pemSend802_2XIDFrame: Out of system buffers. 

Explanation    The system ran out of memory.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-TXXID2: pemPortChangeHandler: Could not send XID frame 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-TXXID3: pemDispatcPortChange: Could not update NPU 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-TXXID4: [chars] 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-3-UNKNOWNMSG: PEMRECV: Received unsupported message type [dec]. 

Explanation    Internal system error

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-WEBAUTHFAIL: Web authentication failure for station 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Web authentication failed.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %PEM-1-WEBAUTHOFF: Unable to enforce web auth policy due to invalid 
state for mobile [hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    Web-authentication is not configured

Recommended Action    Configure web-auth.

Error Message    %PEM-3-WEBEVENT: Bad return from ProcessWebEvent. 

Explanation    Internal system error

Recommended Action    No action is required.

Error Message    %PEM-2-XXX: [chars] 

Explanation    An internal system error occurred.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.