Cisco Wireless LAN Controller System Message Guide 7.0.98.0
USMDB WCP WEB and WPS Messages
Downloads: This chapterpdf (PDF - 303.0KB) The complete bookPDF (PDF - 16.0MB) | Feedback

USMDB WCP WEB and WPS System Messages

Table Of Contents

USMDB WCP WEB and WPS System Messages

USMDB Messages

WCP Messages

WEB Messages

WPS Messages


USMDB WCP WEB and WPS System Messages


This chapter contains the following topics:

USMDB Messages

WCP Messages

WEB Messages

WPS Messages

USMDB Messages

This section contains usmDb API (USMDB) messages.

Error Message    %USMDB-3-MSGTAG001: usmDbAclSwapRuleIndex: The two indices, [dec], are 
the same. 

Explanation    usmDbAclSwapRuleIndex: The two indices, [dec], are the same.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG002: usmDbAclSwapRuleIndex: ACL [chars] or rule [dec] 
does not exist. 

Explanation    usmDbAclSwapRuleIndex: the ACL [chars] or rule [dec] does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG003: usmDbAclSwapRuleIndex: ACL [chars] or rule [dec] 
does not exist. 

Explanation    usmDbAclSwapRuleIndex: the ACL [chars] or rule [dec] does not exist.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG004: invalid arg(s) passed to usmDbCertsWebadminNameGet 

Explanation    invalid arg(s) passed to usmDbCertsWebadminNameGet

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG005: invalid arg(s) passed to usmDbCertsWebauthNameGet 

Explanation    invalid arg(s) passed to usmDbCertsWebauthNameGet

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG006: Cannot add Mobility Member, duplicate IP, Saved 
Member:[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 
Member:[hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP: [dec].[dec].[dec].[dec] 

Explanation    The system cannot add Mobility Member, duplicate IP, Saved Member:[hex]:[hex]:[hex]:[hex]:[hex]:[hex] Member:[hex]:[hex]:[hex]:[hex]:[hex]:[hex], IP: [dec].[dec].[dec].[dec]

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-6-MSGTAG007: Error on call to sysapiRegistryGet routine with 
keyUDI_PID. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keyUDI_PID.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-6-MSGTAG008: Error on call to sysapiRegistryGet routine with 
keyUDI_VID. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keyUDI_VID.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG009: Error on call to sysapiRegistryGet routine with 
keySLOT_DATA_STRUCT. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keySLOT_DATA_STRUCT.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG010: Error on call to sysapiRegistryGet routine with 
keyPORT_DATA_STRUCT. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keyPORT_DATA_STRUCT.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG011: Error on call to sysapiRegistryGet routine with 
keySLOT_DATA_STRUCT. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keySLOT_DATA_STRUCT.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG012: Error on call to sysapiRegistryGet routine with 
keyPORT_DATA_STRUCT. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keyPORT_DATA_STRUCT.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG013: Error on call to sysapiRegistryGet routine with 
keySLOT_DATA_STRUCT. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keySLOT_DATA_STRUCT.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG014: Error on call to sysapiRegistryGet routine with 
keyPORT_DATA_STRUCT. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keyPORT_DATA_STRUCT.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG015: Error on call to sysapiRegistryGet routine with 
keySLOT_DATA_STRUCT. 

Explanation    An error has occurred on a call to the sysapiRegistryGet routine with keySLOT_DATA_STRUCT.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG016: Failed to open [chars] 

Explanation    The system has failed to open [chars]

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG017: Couldn't create flash write semaphore. 

Explanation    The system could not create a flash write semaphore.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-6-MSGTAG018: Setting hardware time to [dec] [dec] [dec] 
[dec]:[dec]:[dec] 

Explanation    The system is setting the hardware time to [dec] [dec] [dec] [dec]:[dec]:[dec].

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG019: unabled to work out gmtime. 

Explanation    The system is unable to work out gmtime.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG020: usmDbTimeGet:Buffer supplied too small [dec]<27 
bytes 

Explanation    usmDbTimeGet:Buffer supplied too small [dec]<27 bytes

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG021: usmDbWcpGet6kTableChecksum(): Non-Doberman 
platform. 

Explanation    usmDbWcpGet6kTableChecksum(): Non-Doberman platform.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG022: usmDbWcpGetControllerSlotPort(): Non-Doberman 
platform. 

Explanation    usmDbWcpGetControllerSlotPort(): Non-Doberman platform.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG023: usmDbWcpGetPeersPortAndIp(): Non-Doberman 
platform. 

Explanation    usmDbWcpGetPeersPortAndIp(): Non-Doberman platform.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG024: usmDbWcpControllerExists(): Non-Doberman 
platform. 

Explanation    usmDbWcpControllerExists(): Non-Doberman platform.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG025: usmDbWcpGetNextController(): Non-Doberman 
platform. 

Explanation    usmDbWcpGetNextController(): Non-Doberman platform.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG026: usmDbWcpGetControllerIPAddress(): Non-Doberman 
platform. 

Explanation    usmDbWcpGetControllerIPAddress(): Non-Doberman platform.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG027: usmDbWcpGetParentRouterName(): Non-Doberman 
platform. 

Explanation    usmDbWcpGetParentRouterName(): Non-Doberman platform.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-4-MSGTAG028: LAG in transition.switch reboot DUE..!!! 

Explanation    LAG is in transition. A switch reboot is due.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %USMDB-3-MSGTAG029: License operation failed with rc : [chars]..!!!  

Explanation    A license operation has failed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    USMDB-0-MSGTAG030: Upgraded ER image required to show version. For 
information regarding Emergency image Version,Please refer Controller documents.

Explanation    An upgraded ER image is required to see the version of the image. For information regarding Emergency image Version, see the Controller documentation.

Recommended Action    .Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    USMDB-0-MSGTAG031: %s: Null pointer passed in.

Explanation    The null pointer has been passed to a function.

Recommended Action    .Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    USMDB-0-MSGTAG032: %s: Buffer for feature name is not big enough.

Explanation    The buffer for the feature name is not big enough.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    USMDB-0-MSGTAG033: AP software being upgraded.

Explanation    The access point software is being upgraded.

Recommended Action    None.

Error Message    USMDB-0-MSGTAG034: usmDbMmMwarAdd: Mobility anchorMac: 
%02x:%02x:%02x:%02x:%02x:%02x:IP: %d.%d.%d.%d lost while updating the group name.

Explanation    usmDbMmMwarAdd: Mobility anchorMac: %02x:%02x:%02x:%02x:%02x:%02x:IP: %d.%d.%d.%d has been lost while updating the group name.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

WCP Messages

This section contains Wireless Control Protocol (WCP) messages.

Error Message    %WCP-3-BUFF_ALLOC_FAILED: Out of System buffers. 

Explanation    The system is out of system buffers.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-BUFF_INVALID: The message buffer received for processing is 
invalid. 

Explanation    The message buffer received for processing is invalid.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-BUFF_LEN_LOW: The length of the buffer [dec] bytes,is not enough 
to hold the data of size [dec] bytes. 

Explanation    The length of the buffer is not enough to hold the data.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-0-CREAT_MUTEX_FAILED: Failed to Create SNMP mutex for WCP task. 

Explanation    The system has failed to create an SNMP mutex for the WCP task.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-0-CREAT_TASK_FAILED: Failed to Create WCP Task. 

Explanation    The system has failed to create the WCP task.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-DISABLE_VAP_FAILED: Failed to disable the Wlans associated with 
the interface [chars]. 

Explanation    The system has failed to disable the WLANS associated with the interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-GET_ADMINSTATE_ERR: Failed to get the admin state for the 
interface [dec]. 

Explanation    The system has failed to get the admin state for a specified interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-GET_GATEWAY_FAILED: Failed to get the gateway for the interface 
[chars]. 

Explanation    The system has failed to get the gateway for an interface.

Explanation    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-GET_IPADDR_FAILED: Failed to get the IP address for the 
interface [chars]. 

Explanation    The system has failed to get the IP address for an interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-GET_MASK_FAILED: Failed to get the net mask for the interface 
[chars]. 

Explanation    The system has failed to get the netmask for an interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-GET_VLAN_FAILED: Failed to get the vlan id for the interface 
[chars]. 

Explanation    The system has failed to get the VLAN ID for an interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-INTERNAL_INTF_NUM_ERR: Failed to get the first available 
internal interface number. 

Explanation    The system has failed to get the first available internal interface number.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-INVALID_REQ_TYPE: Controller got request for invalid TLV type 
[chars]. 

Explanation    The controller received a request for an invalid TLV type.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-INVALID_SLOT_PORT: The next valid slot and port cannot be 
retrieved for the slot [dec] and port [dec] 

Explanation    The next valid slot and port cannot be retrieved.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-IOCTL_FAILED: The ioctl system call failed for the option 
[chars]. 

Explanation    The ioctl system call has failed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-KEEPALIVE_LOST: Lost keepalives from [chars]. 

Explanation    The system has lost keepalives. The expected event on a socket did not occur.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-MGMT_GATEWAY_ILLEGAL: Management interface gateway [chars] is 
illegal. 

Explanation    The management interface gateway is illegal.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-MGMT_IP_ILLEGAL: Management interface IP address [chars] is 
illegal. 

Explanation    The management interface IP address is illegal.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-MGMT_NETMASK_ILLEGAL: Management interface netmask [chars] is 
illegal. 

Explanation    The management interface netmask is illegal.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-MSG_LEN_ZERO: The message received for processing has zero 
length. 

Explanation    The message received for processing has a zero length.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-MSG_TYPE_UNKNOWN: Unknown message type [dec] received for 
processing. 

Explanation    An unknown message type has been received for processing by the WCP task.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-PDU_TRANSMIT_FAILED: Failed to transmit the PDU for the command 
[chars].Return code:[dec]. 

Explanation    The system has failed to transmit the WCP PDU to the SCP.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-SEM_TAKE_FAILED: Could not take a semaphore lock on the global 
snmp structure. 

Explanation    The system could not take a semaphore lock on the global snmp structure.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-SET_IPADDR_FAILED: Failed to set IP address for the interface 
[chars]. 

Explanation    The system has failed to set the IP address for an interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-SET_VLAN_FAILED: Failed to set vlan ID for the interface 
[chars]. 

Explanation    The system has failed to set the VLAN ID for an interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-SOCK_CREAT_FAILED: Failed to create a datagram socket. 

Explanation    The system has failed to create a datagram socket.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-SOCK_OPT_FAILED: Failed to set the socket option [chars]. 

Explanation    The system has failed to set the socket option.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-SOCK_RECV_FAILED: Failed to receive a packet from ip address 
[chars]: port [dec]. 

Explanation    The system has failed to receive a packet on a socket.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-3-SOURCE_INVALID: The message buffer received for processing is 
from an invalid source. 

Explanation    The message buffer received for processing is from an invalid source.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WCP-7-WCP_PORT_BOUND: WCP task is bound to port number [dec]. 

Explanation    The port number to which the WCP task is bound to is displayed.

Recommended Action    No action is required.

Error Message    %WCP-7-WCP_PROCESS_ERROR: wcp process error: The function [chars] 
failed. 

Explanation    A WCP process error has occurred.

Recommended Action    No action is required.

WEB Messages

This section contains web (WEB) messages.

Error Message    %WEB-3-FORM_SUBMIT_FAILED: Form submission failed for file:[chars]. No 
action taken. 

Explanation    A form submit action has failed on the HTML file.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-INVALID_ACCESS_LEVEL: Access level is invalid for SNMPv3 user 
[chars]. 

Explanation    The access level is invalid for this SNMPv3 user.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-INVALID_AP_KEY: Invalid AP Hash Key Provided 

Explanation    The system detects an invalid AP hash key.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-INVALID_AUTH_PROTO: Invalid authentication protocol for SNMPv3 
user [chars]. 

Explanation    The authentication protocol is invalid for the SNMPv3 user.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-INVALID_NLS_TOKEN: NLS String [[dec]] Not Found. 

Explanation    The NLS string has not been found.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-INVALID_PRIV_PROTO: Unknown privacy protocol for SNMPv3 user 
[chars]. 

Explanation    The system has detected an unknown privacy protocol for the SNMPv3 user.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-INVALID_TFTP_DNLDCODE: TFTP download failed with unknown 
failure code. 

Explanation    A TFTP download has failed. The failure code is unknown.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-INVALID_USERNAME: EwsContext cachedUsername is empty! 

Explanation    The cached username is empty.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-LOCAL_AUTH_FAILED: # (prty_order_local_auth.html) Form 
Submission Failed. NoAction Taken.. 

Explanation    # (prty_order_local_auth.html) form submission has failed.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    WEB-0-LOCAL_AUTH_PRTY_ORDER_SET_FAILED: Form Submission Failed.

Explanation    A form submission has failed. The system is not able to set the priority order for the local authentication.

Recommended Action    None.

Error Message    WEB-0-FILE_TRANSFER_FAILED: The file transfer failed with unknown 
failure code.

Explanation    A file transfer has failed. The code for the failure is unknown.

Recommended Action    None.

Error Message    WEB-0-PRTY_ORDER_NET_FAILED: Form Submission Failed.

Explanation    A form submission has failed. An authentication priority has failed for the local net user.

Recommended Action    None.

Error Message    %WEB-3-NLS_LIST_NOT_FOUND: NLS List [[chars]] not found. 

Explanation    The NLS List has not been found.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-NLS_STR_NOT_FOUND: NLS String [[dec]] Not Found for Key: 
[chars] 

Explanation    The NLS string has not been found.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-PARTY_ORDER_NET_FAILED: # (prty_order_net.html) Form 
Submission Failed. No ActionTaken.. 

Explanation    # (prty_order_net.html) The form submission has failed.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-USDB_SAVE_FAILED: The Local Users Database could not be saved 
to flash. 

Explanation    The local users database could not be saved to the flash.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WEB-3-USER_NOT_PRIVILEDGED: Form Submission Failed. The user doesn't 
have the right privileges. 

Explanation    The form submission has failed. The user does not have the correct privileges.

Recommended Action    If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

WPS Messages

This section contains wireless protection policy (WPS) messages.

Error Message    %WPS-6-CONVERT_OLD_SIG_TO_NEW: Old version of signature configuration 
file detected. 

Explanation    An old version of the signature configuration file has been detected. Convert it to the new format.

Recommended Action    This is a debug message only. No action is required.

Error Message    %WPS-3-ERR_OPEN_SIG: Error opening new sig file 

Explanation    An error has occurred while opening a new signature file

Recommended Action    Make sure the signature file is downloaded properly.

Error Message    %WPS-3-ERROR_MASK_NON_HEX: mask string [chars] has non-Hex digits 

Explanation    A mask string has the non-Hex digits.

Recommended Action    Specify a mask string that has Hex digits.

Error Message    %WPS-3-ERROR_PARSE_CST_SIG: Error parsing custom sig file. 

Explanation    An error has occurred while parsing the custom signature file.

Recommended Action    Redownload a new custom signature file to the system.

Error Message    %WPS-3-ERROR_PARSE_SIG_LINE: Error parsing at line [dec] of new sig 
file 

Explanation    An error has occurred while parsing at the line of a new signature file.

Recommended Action    Ensure the signature line has the proper syntax.

Error Message    %WPS-3-ERROR_PARSE_STD_SIG_FILE: Error parsing standard sig file. 

Explanation    An error has occurred while parsing a standard signature file.

Recommended Action    Redownload a new standard signature file to the system.

Error Message    %WPS-3-ERROR_PATTERN_NON_HEX: pattern string [chars] has non-Hex 
digits 

Explanation    A pattern string has the non-Hex digits.

Recommended Action    Specify a pattern string with Hex digits.

Error Message    %WPS-3-ERROR_RETRIEVE_FILE: Error reading file [chars] from flash 

Explanation    An error has occurred while retrieving a file from the flash.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-3-ERROR_SEND_SIG_ADD: Error sending sig Add message to LWAPP 

Explanation    An error has occurred while sending a signature, add the message to the LWAPP.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-3-ERROR_SEND_SIG_DISABLE_MSG: Error sending sig disable message 
to LWAPP 

Explanation    An error has occurred while sending a signature disable message to the LWAPP.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-3-ERROR_SEND_SIG_ENABLE_MSG: Error sending sig enable message to 
LWAPP 

Explanation    An error has occurred while sending a signature enable message to the LWAPP.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-3-ERR_PARSE_REV: Error parsing revision number 

Explanation    An error has occurred while parsing a signature revision number.

Recommended Action    Make sure that the revision number is 1.

Error Message    %WPS-3-ERR_RD_LN: Error reading line [dec] from new sig file 

Explanation    An error has occurred while reading a line from the new signature file.

Recommended Action    Ensure the signature line has the proper syntax.

Error Message    %WPS-3-ERR_READ_SIG_REV: Error reading sig revision number 

Explanation    An error has occurred while reading the signature revision number.

Recommended Action    Specify the evision number at the first line of the signature file.

Error Message    %WPS-3-FAIL_MERGE_SIG: unable to merge rev [chars] sig with existing 
sig 

Explanation    The system is unable to merge signatures with existing signatures.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-3-FAIL_NOTIFY_LWAPP_SIG_FILE: Unable to notify LWAPP of new sig 
file 

Explanation    The system is unable to notify the LWAPP of a new signature file.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-6-IDS_TOKEN_INTERVAL_DEF: Sig Interval set to default 

Explanation    The signature interval has been set to the default.

Recommended Action    No action is required.

Error Message    %WPS-3-INVALID_SIG_TOKEN: Invalid sig token [chars] 

Explanation    The system detects an invalid signature token.

Recommended Action    Correct the signature token that is invalid.

Error Message    %WPS-3-INV_VER: Error invalid version [chars] 

Explanation    The error signature version is invalid.

Recommended Action    Ensure that the revision number is 1.

Error Message    %WPS-4-MFP_INVALID_EVENT_TYPE: MFP Ignoring invalid event type ([int]) 
from [hex]:[hex]:[hex]:[hex]:[hex]:[hex]  

Explanation    MFP ignores the invalid event type.

Recommended Action    This is a debug message only. No action is required.

Error Message    %WPS-3-MFP_LINK_MISSING: MFP Missing link at the [chars] of table 

Explanation    MFP is missing a link in the table.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-0-MFP_STAT_NO_QUEUE: MFP Stats task has no queue 

Explanation    The MFP statistics task has no queue.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-3-MFP_UNLINK_ERR: MFP Can't unlink entry from table 

Explanation    MFP cannot unlink an entry from the table.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %WPS-3-MISSING_SIG_TOKEN: Missing token, the symbol parsed=[chars] 

Explanation    A signature token is missing.

Recommended Action    Correct the signature token that is missing.

Error Message    %WPS-3-NO_SIG_REV: Sig file does not have revision number 

Explanation    The signature file does not have a revision number.

Recommended Action    Specify the revision number at the first line of the signature file, which has to be a of value 1.

Error Message    %WPS-3-NO_VALUE_SIG_TOKEN: No value specified for token [chars] 

Explanation    No value is specified for the signature token.

Recommended Action    Specify the value for the token.

Error Message    %WPS-3-READ_SIG_FILE_FAIL: Error reading line [dec] of new signature 
file 

Explanation    The system cannot read a new signature file.

Recommended Action    Check the signature file on the line to ensure it has the proper syntax.

Error Message    %WPS-4-SIG_ALARM_OFF: AP [hex]:[hex]:[hex]:[hex]:[hex]:[hex] : Alarm 
OFF, [chars] sig [chars], track=[chars] preced=[dec] hits=[dec] slot=[dec] 
channel=[dec] 

Explanation    The signature alarm is off.

Recommended Action    This is a debug message only. No action is required.

Error Message    %WPS-4-SIG_ALARM_OFF_CONT: ...continue, source mac= 
[hex]:[hex]:[hex]:[hex]:[hex]:[hex] 

Explanation    ...continue. The signature alarm is off.

Recommended Action    This is a debug message only. No action is required.

Error Message    %WPS-3-SIG_PTRN_DEL_NUM_INV: illegal number of pattern delimiters 
[chars]. 

Explanation    The number of pattern delimiters is invalid.

Recommended Action    The maximal delimiter number is 3.

Error Message    %WPS-3-SIG_PTRN_INV: invalid pattern [chars] in Version 1 signature. 

Explanation    The signature pattern is invalid.

Recommended Action    Correct the signature pattern.

Error Message    %WPS-3-SIG_PTRN_INV_OFF: invalid offset [chars] in Version 1 signature 

Explanation    The signature pattern offset is invalid.

Recommended Action    Specify the correct pattern offset.

Error Message    %WPS-3-SIG_PTRN_INV_OFF_MAX: offset [chars] in Version 1 signature too 
big; max value = [dec] 

Explanation    The signature pattern offset value is invalid.

Recommended Action    Specify the correct pattern offset value.

Error Message    %WPS-3-SIG_PTRN_INV_OFF_STRT_D: invalid pattern offset Start value 
[dec] in Version 1 signature 

Explanation    The signature pattern offset start is invalid.

Recommended Action    Specify the correct offset start value.

Error Message    %WPS-3-SIG_PTRN_INV_OFF_STRT_S: invalid pattern offset Start value 
[chars] in Version 1 signature 

Explanation    The signature pattern offset start is invalid.

Recommended Action    Specify the correct offset start value.

Error Message    %WPS-3-SIG_PTRN_LEN_OVER: pattern string cannot specify more than 
[dec] octets in Version 1 signatures 

Explanation    The pattern string length is too big.

Recommended Action    Specify the correct pattern string.

Error Message    %WPS-3-SIG_PTRN_MASK_EQ: pattern string and mask must be of equal 
length in Version 1 signatures 

Explanation    The pattern string and mask must have an equal length.

Recommended Action    Make sure that the pattern string and mask have an equal length.

Error Message    %WPS-3-SIG_PTRN_MASK_EVEN: pattern string and mask must have an even 
number of bytes in Version 1 signatures 

Explanation    The pattern string and mask must have an even number of bytes.

Recommended Action    Make sure that the pattern string and mask have an even number of bytes.

Error Message    %WPS-3-SIG_PTRN_MASK_NULL: pattern string and mask have no any bytes 
specified 

Explanation    The pattern string and mask do not have any bytes specified.

Recommended Action    Specify the pattern and mask.

Error Message    %WPS-3-SIG_PTRN_MASK_STR_INV: [chars] string [chars] has non-Hex 
digits 

Explanation    The signature pattern or mask string is invalid. It has non-Hex digits.

Recommended Action    Make sure that the signature pattern or mask string has Hex digits.

Error Message    %WPS-3-SIG_PTRN_MISSING: invalid pattern [chars] in Version 1 
signature: missing [chars]. 

Explanation    The signature pattern is invalid.

Recommended Action    Correct the signature pattern.

Error Message    %WPS-3-SIG_PTRN_PARSE_FAIL: Error parsing pattern [chars] in Version 
1 signature 

Explanation    An error has occurred while parsing the token pattern.

Recommended Action    Specify the correct pattern.

Error Message    %WPS-3-SIG_STR_INV: [chars] string must begin with '0x' in Version 1 
signatures 

Explanation    The signature pattern is invalid.

Recommended Action    Specify the correct signature pattern.

Error Message    %WPS-3-SIG_TOKEN_DUP: Sig [chars] must be unique, the '[chars]' 
repeats 

Explanation    The signature token is not unique.

Recommended Action    Specify a unique signature token.

Error Message    %WPS-3-SIG_TOKEN_DUP_PRECED: Sig precedence must be unique, the [dec] 
repeats 

Explanation    The signature token precedence is not unique.

Recommended Action    Specify a unique precedence ID.

Error Message    %WPS-3-SIG_TOKEN_NUM_INV: Version 1 sig cannot have more than [dec] 
tokens per line 

Explanation    Version 1 signatures cannot have more than 15 tokens per line

Recommended Action    Specify a signature that has less than 15 tokens.

Error Message    %WPS-3-SIG_TOKEN_WRONG_SIGID: Sig Id   [dec] is not valid  

Explanation    The signature token SigId is not valid.

Recommended Action    Specify a valid SigId.

Error Message    %WPS-3-SIG_VER_UNSUP: Signature version number [chars] is unsupported 

Explanation    The signature version number is unsupported.

Recommended Action    Make sure that the revision number is 1.

Error Message    %WPS-3-TOKEN_MISSING_INVALID: Missing or invalid '[chars]' token in 
Version 1 sig 

Explanation    There is a missing or invalid token in the Version 1 signature.

Recommended Action    Correct the invalid token.

Error Message    %WPS-3-TOKEN_PARSE_FAIL: Error processing '[chars]' token in Version 
1 signature 

Explanation    The signature token processing has failed.

Recommended Action    Correct the token.

Error Message    %WPS-3-TYPE_TOKEN_INV_GT: In Version 1 signatures, '[chars]' can not 
have a value greater than [dec] 

Explanation    The signature token value is invalid.

Recommended Action    Specify the correct value for the token.

Error Message    %WPS-3-TYPE_TOKEN_INV_VAL1: In Version 1 signatures, '[chars]' can 
only have value [chars] 

Explanation    The signature token value is invalid.

Recommended Action    Specify the correct value for the token.

Error Message    %WPS-3-TYPE_TOKEN_INV_VAL2: In Version 1 signatures, '[chars]' can 
only have value [chars] or [chars] 

Explanation    The signature token value is invalid.

Recommended Action    Specify the correct value for the token.

Error Message    %WPS-3-TYPE_TOKEN_INV_VAL3: In Version 1 signatures, '[chars]' can 
only have value [chars], [chars], or [chars] 

Explanation    The signature token value is invalid.

Recommended Action    Specify the correct value for the token.

Error Message    %WPS-4-UNSUPPORT_SIG_VER: Unsupported sig version on line [dec], 
ignoring signature 

Explanation    There is an unsupported signature version. The system is ignoring the signature.

Recommended Action    Make sure that the revision number is 1.

Error Message    %WPS-3-VER_NOT_FOUND: Error version number not found 

Explanation    The signature version number has not been found.

Recommended Action    Specify a revision number that has a value of 1.

Error Message    %WPS-3-VER_NUM_MISSING_INVALID: Error at line [dec] of new signature 
file: version number is missing or invalid 

Explanation    The version number is missing or invalid.

Recommended Action    Specify the revision number at the first line of the signature file, which has to be a value of 1.