Cisco Wireless LAN Controller System Message Guide 7.0.98.0
IPSTAT L7API L7COMM and LAG Messages
Downloads: This chapterpdf (PDF - 123.0KB) The complete bookPDF (PDF - 16.0MB) | Feedback

IPSTAT L7API L7COMM and LAG System Messages

Table Of Contents

IPSTAT L7API L7COMM and LAG System Messages

IPSTAT Messages

L7API Messages

L7COMM Messages

LAG Messages


IPSTAT L7API L7COMM and LAG System Messages


This chapter contains the following topics:

IPSTAT Messages

L7API Messages

L7COMM Messages

LAG Messages

IPSTAT Messages

This section contains IP statistics (IPSTAT) messages.

Error Message    %IPSTAT-3-STATS_CREATE_FAIL: ipStatsCreate: Could not create [chars] 
counters for interface [dec]. 

Explanation    The system could not create statistical counters. Internal System Error

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

L7API Messages

This section contains L7API subsystem (L7API) messages.

Error Message    %L7API-0-SYS_INIT_FAIL: SystemInitStatus is corrupt [hex] 

Explanation    The SystemInitStatus is corrupt.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

L7COMM Messages

This section contains L7COMM subsystem (L7COMM) messages.

Error Message    %L7COMM-3-ACL_NAME_TOO_LONG: aclName too long 

Explanation    The aclName is too long.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %L7COMM-3-VLAN_NAME_TOO_LONG: vlanIfName too long 

Explanation    The vlanIfName is too long.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

LAG Messages

This section contains Link Aggregation (LAG) messages.

Error Message    %LAG-0-TASK_CREATE_FAIL: Could not create Lag Task. Lag not 
initialized 

Explanation    The system could not create LAG task. The LAG is not initialized.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-0-QUEUE_CREATE_FAIL: Unable to create msg queue for Lag Task. Lag 
initialization failed. 

Explanation    The system is unable to create a message queue for the LAG task. LAG initialization has failed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-CMD_WAIT_FAIL: Lag command failed to complete for Interface: 
[dec]. 

Explanation    The LAG command has failed to complete for an interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-CONFIG_INIT_FAIL: Failed to apply component startup 
configuration for Lag. 

Explanation    The system has failed to apply the component startup configuration for LAG.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-CREATE_NEW_FAIL: Could not create LAG from NV config data entry. 

Explanation    The system could not create the LAG from the NV configuration data entry.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-CRTLBLK_GET_FAIL: Cannot create LAG '[chars]'. Exceeded Maximum 
number of LAG interfaces possible. 

Explanation    Cannot create the LAG. The maximum number of LAG interfaces have been exceeded.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-FILE_WRITE_FAIL: Failed to write to configuration  file 
[chars]. 

Explanation    The system has failed to write to the configuration file.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-INIT_FAIL: Failed to initialize Link Aggregation. 

Explanation    The system has failed to initialize Link Aggregation.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-INTF_FIND_FAIL: Interface [dec] not found in LAG [dec] member 
list. 

Explanation    The interface has not been found in the LAG member list.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-INVALID_COMMAND: Invalid command received. 

Explanation    An invalid command has been received.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-INVALID_CONFIG_PARAMS: Cannot create LAG '[chars]'. Invalid 
configuration parameters. 

Explanation    Cannot create the LAG because of invalid configuration parameters.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-MODIFY_FAIL: Failed to modify LAG [chars]. Invalid 
configuration parameters. Try configuring without any members or all members must 
be full-duplex and have same speed. Interface: [dec] 

Explanation    The system has failed to modify the LAG because of invalid configuration parameters. Try configuring without any members or all members must be full-duplex and have the same speed.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-MODIFY_INTERNAL_ERR: Failed to modify LAG [chars]. Internal 
system error. Interface: [dec] 

Explanation    The system has failed to modify the LAG because of internal system error.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-MSG_SND_FAIL: Failed to send message to Lag for a state change 
request. Interface: [dec] 

Explanation    The system has failed to send a message to the LAG for a state change request.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-NIM_INFOGET_FAIL: Could not get NIM information for LAG 
interface [dec]. Failed to initialize LAG. 

Explanation    The system could not get NIM information for a LAG interface. The system has failed to initialize the LAG.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-NV_READ_FAIL: Error retrieving file [chars] from flash 

Explanation    An error occurred while retrieving the file from the flash memory.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-REG_CALBAK_FAIL: Unable to register for interface state 
changeLAG not initialized. 

Explanation    The system is unable to register for an interface state change. The LAG is not initialized.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-4-INCOMPATIBLE_PORT_SPEED: All members of lag must have same 
speed. Interface [dec] has speed different from all other members of Lag. Removing 
from Lag. 

Explanation    All members of the LAG must have the same speed. One of the members of the LAG has a different speed different than all other members. The system is removing that interface from the port bundle.

Recommended Action    No action is required.

Error Message    %LAG-4-INTF_SPEED_UPDATED: Speed of interface [dec] updated with the 
speed of all other members of Lag. 

Explanation    The speed of the interface has been updated with the speed of all other members of the LAG.

Recommended Action    No action is required.

Error Message    %LAG-3-STAT_INIT_FAIL: Failed to initialize statistical counters for 
interface. Interface: [dec]  

Explanation    The system has failed to initialize statistical counters for an interface.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %LAG-3-TASK_SYNC_FAIL: Could not synchronize the Lag TASK. Lag not 
initialized. 

Explanation    The system could not synchronize the Lag TASK. Lag not initialized.

Recommended Action    Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.