Quick Start Guide: 1000BASE-SX, 1000BASE-LX and 1000BASE-T SFP Modules for Cisco 4400 Series Wireless LAN Controllers
Installation
Downloads: This chapterpdf (PDF - 1.27MB) | Feedback

Installation

Table Of Contents

Installation

Safety Warning

Class 1 Laser Product

Installing an SFP Module

Laser Radiation

Removing an SFP Module


Installation


This document provides a brief description about the different SFP modules and how to install these modules in a Cisco 4400 Series Wireless LAN Controller to provide Gigabit Ethernet connectivity.

The following SFP modules can be installed:

1000BASE-SX SFP modules that provide a 1000 Mbps wired connection to a network through an 850nM (SX) fiber-optic link using an LC physical connector.

1000BASE-LX SFP modules that provide a 1000 Mbps wired connection to a network through a 1300nM (LX/LH) fiber-optic link using an LC physical connector.

1000BASE-T SFP modules that provide a 1000 Mbps wired connection to a network through a copper link using an RJ-45 physical connector.

Figure 1 SFP Modules

Safety Warning


Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.


Class 1 Laser Product

Warning


Class 1 laser product. Statement 1008

Waarschuwing

Klasse-1 laser produkt.

Varoitus

Luokan 1 lasertuote.

Attention

Produit laser de classe 1.

Warnung

Laserprodukt der Klasse 1.

Avvertenza

Prodotto laser di Classe 1.

Advarsel

Laserprodukt av klasse 1.

Aviso

Produto laser de classe 1.

¡Advertencia!

Producto láser Clase I.

Varning!

Laserprodukt av klass 1.

Aviso

Produto a laser de classe 1.

Advarsel

Klasse 1 laserprodukt.



Installing an SFP Module

To install a 1000BASE-SX, 1000BASE-LX, or 1000BASE-T SFP module into the front panel of a Cisco 4400 Series Wireless LAN Controller, perform these steps:


Step 1 Disconnect all cables from the Cisco 4400 Series Wireless LAN Controller.

Step 2 Find the slots for the SFP modules on the front panel of the Cisco 4400 Series Wireless LAN Controller.

Figure 2 Cisco 4400 Series Wireless LAN Controller Models


Note Do not remove the rubber protectors on the end of the 1000BASE-SX or 1000BASE-LX modules until they are installed and ready for cable connection and use.


Step 3 Insert the SFP module into the slot with the printed label facing up.

Step 4 Gently but firmly press the SFP module into the slot until it is firmly seated in the module electrical connector.

Step 5 Connect all the cables and restore power to restart the Cisco 4400 Series Wireless LAN Controller.

Laser Radiation

Warning


Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051

Waarschuwing

Losgekoppelde of losgeraakte glasvezels of aansluitingen kunnen onzichtbare laserstraling produceren. Kijk niet rechtstreeks in de straling en gebruik geen optische instrumenten rond deze glasvezels of aansluitingen.

Varoitus

Irrotetuista kuiduista tai liittimistä voi tulla näkymätöntä lasersäteilyä. Älä tuijota säteitä tai katso niitä suoraan optisilla välineillä.

Attention

Les fibres ou connecteurs débranchés risquent d'émettre des rayonnements laser invisibles à l'œil. Ne regardez jamais directement les faisceaux laser à l'œil nu, ni d'ailleurs avec des instruments optiques.

Warnung

Unterbrochene Fasern oder Steckerverbindungenkönnen unsichtbare Laserstrahlung abgeben. Blicken Sie weder mit bloßem Auge noch mit optischen Instrumenten direkt in Laserstrahlen.

Avvertenza

Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono mai essere osservati direttamente o attraverso strumenti ottici.

Advarsel

Det kan forekomme usynlig laserstråling fra fiber eller kontakter som er frakoblet. Stirr ikke direkte inn i strålene eller se på dem direkte gjennom et optisk instrument.

Aviso

Radiação laser invisível pode ser emitida de conectores ou fibras desconectadas. Não olhe diretamente para os feixes ou com instrumentos ópticos.

¡Advertencia!

Es posible que las fibras desconectadas emitan radiación láser invisible. No fije la vista en los rayos ni examine éstos con instrumentos ópticos.

Varning!

Osynlig laserstrålning kan avges från frånkopplade fibrer eller kontaktdon. Rikta inte blicken in i strålar och titta aldrig direkt på dem med hjälp av optiska instrument.

Aviso

Radiação laser invisível pode ser emitida a partir de fibras ou conectores desconectados. Não fixe o olhar nos feixes e nem olhe diretamente com instrumentos ópticos.

Advarsel

Usynlig laserstråling kan forekomme fra brugte fibre eller stik. Stir ikke ind i stråler eller direkte med optiske instrumenter.



You have installed the SFP module in the Cisco 4400 Series Wireless LAN Controller.


Removing an SFP Module

To remove the SFP module from the front panel of a Cisco 4400 Series Wireless LAN Controller, perform these steps:


Step 1 Remove the power cord from the Cisco 4400 Series Wireless LAN Controller.

Step 2 Remove the cable connected to the SFP module, if any.

Step 3 Pull the bail towards you to release the SFP module.

Step 4 Replace the rubber optical protector on the 1000BASE-SX or 1000BASE-LX module by pressing it into the end of the SFP module.

Step 5 Pull the SFP module out of the Cisco 4400 Series Wireless LAN Controller.

Step 6 Plug the power cord back and restore power to restart the Cisco 4400 Series Wireless LAN Controller.

You have removed the SFP module from the Cisco 4400 Series Wireless LAN Controller.