Cisco IOS Command Reference for Cisco Aironet Access Points for Cisco IOS Releases 15.2(4)JA
Appendix A - List of Supported Cisco IOS Commands
Downloads: This chapterpdf (PDF - 174.0KB) The complete bookPDF (PDF - 4.75MB) | Feedback

List of Supported Cisco IOS Commands

Table Of Contents

List of Supported Cisco IOS Commands

A

B

C

D

E

F

G

H

I

L

M

N

P

R

S

T

U

V

W


List of Supported Cisco IOS Commands


This appendix lists the Cisco IOS commands that access points and bridges support. Cisco IOS commands that are not in this list have not been tested on access points and bridges and might not be supported.

You can find descriptions and usage instructions for the rest of the commands in this list in the Cisco IOS Release 12.3 Master Indexes. Click this URL to browse to the master indexes:

http://www.cisco.com/en/US/docs/ios/mcl/123mcl/TD-Book-Wrapper.html

A

aaa accounting

aaa accounting delay-start

aaa accounting update

aaa authentication

aaa authentication login

aaa authentication login default local cache

aaa authorization exec default local cache

aaa cache profile

aaa pod server

aaa new-model

aaa pod server access-class


Note The access-class command is supported only on access points that have a console port.


access-list

accounting (SSID configuration mode)

admission-control (QOS Class interface configuration mode)


Note This command is not supported on repeaters.


admit-traffic (QOS Class interface configuration mode)


Note This command is not supported on repeaters.


anonymous-id (dot1x credentials configuration mode)

antenna

ampdu

archive download-sw

archive upload

arp

authentication (local server configuration mode)

authentication client

authentication key-management

authentication key-management wpa version 2 dot11r

authentication network-eap (SSID configuration mode)

authentication open (SSID configuration mode)

authentication shared (SSID configuration mode)

B

beacon

beacon privacy guest-mode

bgp-policy

boot buffersize

boot ios-break

boot mode-button

boot upgrade

bridge


Note The bridge 1 protocol ieee command is not supported on access points and bridges. You cannot disable this command unless you reboot the unit.


bridge aging-time

bridge forward-time

bridge hello-time

bridge max-age

bridge priority

bridge protocol ieee

bridge-group block-unknown-source

bridge-group input-address-list

bridge-group input-pattern-list

bridge-group input-type-list

bridge-group output-address-list

bridge-group output-pattern-list

bridge-group output-type-list

bridge-group path-cost

bridge-group port-protected

bridge-group priority

bridge-group spanning-disabled

bridge-group subscriber-loop-control

bridge-group source-learning

bridge-group unicast-flooding

broadcast-key

C

cache authentication profile

cache authorization profile

cache expiry

cca

cd

cdp enable

cdp holdtime

cdp run

cdp timer

channel

channel-match (LBS configuration mode)

class-map

clear access-list counters

clear cdp counters

clear cdp table

clear dot11 aaa authentication mac-authen filter-cache

clear dot11 cckm-statistics

clear dot11 client

clear dot11 hold-list

clear dot11 next-aps

clear dot11 statistics

clear dot11 ids mfp client statistics

clear eap sessions

clear iapp rogue-ap-list

clear iapp statistics

clear ip igmp snooping membership

clear logging

clear vlan

clear wlccp wds

clear wlccp wds recovery statistics

clock timezone

clock summer-time

concatenation

configure terminal

copy

copy run scp://url

countermeasure tkip hold-time

crypto key generate rsa

crypto pki authenticate

crypto pki enroll

crypto pki import

crypto pki trustpoint

cw-max (QOS Class interface configuration mode)

cw-min (QOS Class interface configuration mode)

D

databits


Note The databits command is supported only on access points that have a console port.


debug aaa pod

debug cdp adjacency

debug cdp events

debug cdp packets

debug dot11

debug dot11 aaa

debug dot11 cac


Note This command is not supported on repeaters.


debug dot11 dot11radio

debug dot11 ft

debug dot11 ft-scan

debug dot11 ids

debug dot11 ids mfp

debug eap

debug iapp

debug interface fastethernet

debug ip http authentication

debug ip http ssi

debug ip http tokens

debug ip http transactions

debug ip http url

debug ip igmp snooping

debug radius local-server

debug vlan packets

debug wlccp ap

debug wlccp ap mn---tbd

debug wlccp ap rm enhanced-neighbor-list

debug wlccp packet

debug wlccp rmlib

debug wlccp wds

delete

description (dot1x credentials configuration mode)

dfs band

dir

disable

disconnect

distance

dot11 aaa authentication attributes service

dot11 aaa authentication mac-authen filter-cache

dot11 aaa csid

dot11 activity-timeout

dot11 adjacent-ap age-timeout

dot11 antenna-alignment

dot11 arp-cache

dot11 association mac-list

dot11 auto-immune

dot11 band-select parameters

dot11 carrier busy

dot11 dot11r pre-authentication

dot11 dot11r re-association timer

dot11 extension aironet

dot11 extension power native

dot11 guest username

dot11 holdoff-time

dot11 ids eap attempts

dot11 ids mfp

dot11 igmp snooping-helper

dot11 lbs

dot11 linktest

dot11 location isocc

dot11 mbssid

dot11 meter

dot11 network-map

dot11 phone

dot11 priority-map avvid

dot11 qos class

dot11 ssid

dot11 ssid band-select

dot11 update-group-key

dot11 vlan-name

dot11 wpa handshake init-delay

dot11 wpa handshake timeout

dot1x credentials

dot1x eap profile (configuration interface mode)

dot1x eap profile (SSID configuration mode)

dot1x timeout reauth-period

dot1x timeout supp-response

duplex

E

eap profile

eapfast authority

eapfast pac expiry

eapfast server-key

enable

encapsulation dot1q

encryption

encryption key

encryption mode ciphers

encryption mode wep

end

erase

exception core-file

exception crashinfo buffersize

exception crashinfo file

exception dump

exception flash

exception memory

exec-timeout

exit

F

fair-queue

fixed-slot (QOS Class interface configuration mode)

format

fragment-threshold

full-duplex

G

group (local server configuration mode)

guard-interval

guest-mode (SSID configuration mode)

H

half-duplex

help

hold-queue

holdoff-time

hostname

I

iapp path destination

iapp path destination source

iapp standby mac-address

iapp standby poll-frequency

iapp standby primary-shutdown

iapp standby timeout

ids mfp client

information-element ssidl (SSID configuration mode)

infrastructure-client

infrastructure-ssid (SSID configuration mode)

interface

interface dot11 (LBS configuration mode)

interface dot11radio

interface fastethernet


Caution Access points and bridges do not support the interface loopback command. Configuring a loopback interface might generate an IAPP GENINFO storm on your network.

interface virtual-dot11Radio

ip access-group

ip access-list

ip address

ip address dhcp

ip admission web_passthrough

ip default-gateway

ip dhcp-server

ip domain-lookup

ip http authentication

ip http help-path

ip http path

ip http port

ip http server

ip igmp snooping vlan

ip name-server

ip redirection

ip telnet

ipv6 access-list

ipv6 address autoconfig

ipv6 address dhcp rapid-commit

ipv6 address ipv6-address link-local

ipv6 nd autoconfig

ipv6 nd cache

ipv6 nd dad

ipv6 nd na glean

ipv6 nd ns-interval

ipv6 nd reachable-time

ipv6 traffic-filter

L

l2-filter bridge-group-acl

l2-filter-block-arp

led display

led flash

length


Note The length command is supported only on access points that have a console port.


line

logging

logging buffered

logging snmp-trap

logging console

logging history

logging history size

logging facility

logging monitor

logging on

logging rate-limit

logging trap

login

logout


Note The loopback command is not supported on access points and bridges.


M

match (class-map configuration)

max-associations (SSID configuration mode)

mbssid

mbssid (SSID configuration mode)

method (eap profile configuration mode)

method (LBS configuration mode)

mobile station

mobility network-id

monitor


Note The monitor command is supported only on access points that have a console port.


more

multicast address (LBS configuration mode)

N

nas (local server configuration mode)

P

packet max-retries

packet retries

packet speed

packet timeout

packet-type (LBS configuration mode)

parent

parent timeout

parity


Note The parity command is supported only on access points that have a console port.


password (dot1x credentials configuration mode)

payload-encapsulation

pki-trustpoint (dot1x credentials configuration mode)

ping

policy-map

power client

power inline negotiation

power local

preamble-short

privilege


Note The privilege command is supported only on access points that have a console port.


probe-response gratuitous

pwd

R

radius server

radius local-server pac-generate

radius-server attribute

radius-server deadtime

radius-server host

radius-server local

radius-server retransmit

radius-server timeout

radius-server vsa send accounting

reload

routing dynamic

rts

S

server-address (LBS configuration mode)

service-policy output

service sequence-number

service timestamps

session-timeout


Note The session-timeout command is supported only on access points that have a console port.


short-slot-time

show access-lists

show boot

show boot mode-button

show bridge

show bridge group

show buffers

show cdp

show cdp entry

show cdp interface

show cdp neighbors

show cdp traffic

show clock

show controllers dot11radio

show controllers fastethernet

show debugging

show dhcp server

show dot11 aaa authentication mac-authen filter-cache

show dot11 adjacent-ap

show dot11 associations

show dot11 bssid

show dot11 cac


Note This command is not supported on repeaters.


show dot11 carrier busy

show dot11 directed-roam

show dot11 ids eap

show dot11 ids mfp

show dot11 neighbor-ap

show dot11 network-map

show dot11 statistics client-traffic

show dot11 traffic-streams

show dot11 vlan-name

show dot1x

show dot1x credentials

show eap registrations

show eap sessions

show environment

show file information

show file systems

show flash

show history

show hosts

show html users

show iapp rogue-ap-list

show iapp standby-parms

show iapp statistics

show interfaces dot11radio

show interfaces dot11radio aaa

show interfaces dot11radio statistics

show interfaces fastethernet

show ip access-list


Note The show ip local command is not supported on access points and bridges.


show ip igmp snooping groups

show ip igmp snooping vlan

show led flash

show line

show logging

show memory

show power-injector

show privilege

show processes

show queueing

show radius

show radius local-server statistics

show registry

show running-config

show running-config ssid

show sessions

show smf

show snmp

show snmp engineID

show snmp group

show snmp user

show spanning-tree

show specrum recover | status

show stacks

show startup-config

show subsys

show tech-support

show terminal

show users

show version

show vlan

show wlccp

show wlccp ap mn

show wlccp ap rm enhanced-neighbor-list

shutdown

snmp ifindex

snmp-server

snmp-server chassis-id

snmp-server community

snmp-server contact

snmp-server enable traps

snmp-server enable traps envmon temperature

snmp-server group

snmp-server host

snmp-server location

snmp-server system-shutdown

snmp-server user

snmp-server view

snmp trap link-status

speed (Ethernet interface)

speed (radio interface)

speed (serial line interface)


Note The speed (serial line interface) command is supported only on access points that have a console port.


speed ofdm

ssid

station-role

station-role install

stopbit


Note The stop bit command is supported only on access points that have a console port.


T

terminal-type


Note The terminal-type command is supported only on access points that have a console port.


test fastethernet

test led

timeout (serial line interface)


Note The timeout (serial line interface) command is supported only on access points that have a console port.


traffic-class

traffic-stream


Note This command is not supported on repeaters.


transmit-op (QOS Class interface configuration mode)

U

undebug

user (local server configuration mode)

username (dot1x credentials configuration mode)

username privilege password

V

verify

vlan (SSID configuration mode)

W

web-auth

width

wlccp ap eap profile

wlccp ap username

wlccp authentication-server

wlccp wds aaa authentication mac-authen filter-cache

wlccp wds mode wds-only

wlccp wds priority

wlccp wnm ip address

workgroup-bridge client-vlan

workgroup-bridge timeouts assoc-response

workgroup-bridge timeouts auth-response

workgroup-bridge timeouts client-add

workgroup-bridge timeouts eap-timeout

workgroup-bridge timeouts iapp-refresh

workgroup-bridge unified-vlan-client

world-mode

wpa-psk

write memory

write terminal