Cisco Unity Express 2.3 CLI Administrator Guide
Configuring Message Notification
Downloads: This chapterpdf (PDF - 397.0KB) The complete bookPDF (PDF - 3.45MB) | Feedback

Configuring Message Notification

Table Of Contents

Configuring Message Notification

Overview of Message Notification

Notification Profile

Message Notification Settings

System-Wide Message Notification Settings

Subscriber and Device-Specific Settings

Options and Settings

Sending and Receiving Message Notifications

Notifications to Phone Devices

Notifications to Numeric Pagers

Notifications to E-mail Inboxes

Notifications to Text Pagers

Configuring System-Wide Settings

Required Data for This Procedure

Examples

Enabling Message Notification for a Subscriber or Group

Configuring Message Notification for Devices

Configuring Message Notification for Phone Devices

Prerequisites

Required Data for This Procedure

Examples

Configuring Message Notification for a Numeric Pager

Prerequisites

Required Data for This Procedure

Examples

Configuring Message Notification for E-mail

Prerequisites

Required Data for This Procedure

Examples

Configuring Message Notification for a Text Pager

Prerequisites

Required Data for This Procedure

Examples


Configuring Message Notification


Last Updated: July 25, 2006

This chapter describes the procedures for implementing the Cisco Unity Express message notification feature and includes the following sections:

Overview of Message Notification

Message Notification Settings

Sending and Receiving Message Notifications

Configuring System-Wide Settings

Enabling Message Notification for a Subscriber or Group

Configuring Message Notification for Devices

To configure this feature from the GUI, use the Voice Mail > Message Notification option.

Overview of Message Notification

Cisco Unity Express 2.3 provides several options for notifying subscribers of new messages in their voice mailboxes.

The system generates notifications for all types of messages, including nondelivery receipts (NDRs), when the messages arrive in a subscriber's mailbox. Delayed delivery receipts (DDRs), broadcast messages, and existing messages marked as new do not generate notifications.

The system generates a notification when a new voice-mail message arrives in a subscriber's mailbox. These notifications can be sent to the following devices:

Cell phone

Home phone

Work phone

Numeric pager

Text pager

E-mail inbox

Each device has a configurable schedule during which notifications can be received. For phone devices (work phone, home phone, and cell phone), the subscriber has the option to disable notification or to log in to the mailbox during the notification call.

A notification profile contains the configuration settings for each subscriber or group. See "Notification Profile" for more information about the notification profile.

Configuring the message notification features requires setting several system-wide parameters. See "System-Wide Message Notification Settings" for the procedure to set these parameters.

Sending and receiving message notifications differs by device type. See "Sending and Receiving Message Notifications" for a description of these processes.

After configuring the system-wide parameters, configure the parameters for the subscribers and groups who will have access to the message notification feature. See "Configuring Message Notification for Devices" for these procedures.

Notification Profile

Cisco Unity Express 2.3 provides a default notification profile for each subscriber and group that has a voice mailbox. The notification profile contains configuration information for message notification, such as a device type, phone number or e-mail address, notification preference, and notification schedule. Each subscriber or group can have one or more of the supported devices configured in the notification profile. After the profile information is configured, the subscriber or group will receive message notifications.

The default profile name is vm-notif-profile. This name cannot be changed or deleted.

Message Notification Settings

Configuring Message Notification requires the following procedures:

Configuring system-wide settings

Configuring subscriber- and device-specific settings

System-Wide Message Notification Settings

Message notifications for the whole system use the following settings:

Enabling the feature—Message notification is disabled by default for all subscribers and groups. Enable the feature on a system-wide basis or for specific subscribers or groups. The feature is available for all subscribers and groups who have a mailbox.

The first time the administrator enables the feature system-wide, the feature remains disabled for all subscribers and groups. If specific subscribers or groups are to have access to message notification, the administrator can enable the feature for those subscribers or groups on an individual basis.

If the feature is disabled on a system-wide basis, the feature becomes disabled for all subscribers and groups. However, the system does not delete the device settings for the subscribers and groups. When the feature is enabled again, the system restores the settings for the subscribers and groups as they were before the system-wide disabling.

If the feature is enabled system-wide and the administrator adds a new subscriber or group, the feature is disabled for that subscriber or group.

If no SMTP server is configured when the feature is enabled system-wide, the system generates a warning message indicating that e-mail and text pager notifications will not work.

Notification preference—The administrator can set the type of messages for which notifications will be sent: all messages or urgent messages. Urgent is the default. The administrator can change the preference for specific subscribers or groups to a value other than the system-wide setting.

If the system-wide preference is set to "all," the administrator can set the preference for a specific subscriber or group to either "all" or "urgent." If the system-wide preference is set to "urgent," the preference for a specific subscriber or group is only "urgent."

If the administrator changes the system-wide preference from "all" to "urgent," the system changes the preference to "urgent" for all subscribers and groups.

If the administrator changes the system-wide preference from "urgent" to "all," the system does not change the preference for those subscribers or groups who were configured on an individual basis.

Voice message attachments—This setting permits a voice message to be attached to a notification sent to an e-mail inbox. Notification attachments are disabled by default so that voice messages are not attached to the notification e-mail. The administrator can change this setting for specific subscribers or groups to a value other than the system-wide setting.

If attachments are enabled system-wide, you can change the setting for a specific subscriber or group to enabled or disabled. If attachments are disabled system-wide, the attachments setting for a specific subscriber or group also is disabled.

The system never attaches a private message to notification e-mails, regardless of this setting.

If the administrator changes this system-wide setting from enabled to disabled, the system changes the setting to disabled for all subscribers and groups.

If the administrator changes this system-wide setting from disabled to enabled, the system does not change the preference for those subscribers or groups who were configured on an individual basis.

Connection timeout—This variable specifies the number of seconds a notification call will attempt to connect before the system disconnects the call and treats the call as failed. This option is available only to phone devices and numeric pagers. The range of values is 12 seconds to 96 seconds. The default value is 48 seconds.

Logging into voice mail during an outcall—This variable permits the subscriber to log in to voice mail when answering a notification call. This option is available only for phone devices.

If the option is enabled, the system provides the subscriber with an option to log in to voice mail to retrieve the message. If the option is disabled, the system plays a notification prompt three times before disconnecting the notification call. The system default is disabled.

Restriction table—The restriction table controls the phone numbers that subscribers can use to send message notifications. These restrictions are available only for phone devices and numeric pagers.

The system provides a predefined table that can be modified by the administrator. The table applies to all subscribers and groups on the system. A typical use of this table is to prevent the use of long-distance or international numbers for message notifications.

The system checks the restriction table when the subscriber is assigning phone numbers to phone devices (such as a cell phone, home phone, or work phone), to a numeric pager, and before making an outcall. If a phone number is listed in the table as restricted, the system sends a message to the subscriber.

If a subscriber has a number configured for a device and the administrator later restricts that number system-wide, notification calls will not be made to that number. The administrator must remove the number for the individual subscriber.

Cisco Unity Express provides a default restriction table that defines two requirements:

Minimum and maximum number of digits, including access codes, allowed in a phone number. The minimum is 1 digit and the maximum is 30 digits. The default is 1 digit.

A maximum of 10 dial strings that represent the restricted numbers. Each string consists of a call pattern and a setting that specifies if a phone number matching the pattern is restricted or not.

Valid patterns can include digits 0 to 9, asterisk (*), and dot (.). The * indicates a match of zero or more digits. Each dot serves as a placeholder for 1 digit.

Valid setting values are allowed or disallowed.

When a subscriber tries to set up or change a phone number assigned to a device, the system verifies that the number has the allowed number of digits. If it does not, the subscriber receives a system message.

If the number of digits is acceptable, the system checks the number against the dial patterns in the restriction table, starting with the first pattern (preference 1). If the number does not match the first pattern, the system checks the next pattern in the table (preference 2), and so forth until a match is found. The system either permits or restricts the call as specified in the dial string.

The default restriction table permits all phone numbers to be used, as shown in Table 15.

Table 15 Default Restriction Table

Preference
Call Pattern
Allowed

1

*

Yes


You can change only the preference and permission of this pattern.

The restriction table can contain identical dial strings, which have the same call pattern and permission setting. This includes the default pattern. You can delete any of these dial strings if the table contains at least one default pattern.

Table 16 illustrates a restriction table with international numbers and restricted numbers.

Table 16 Restriction Table with International Numbers

Preference
Call Pattern
Allowed

1

9011*

No

2

91..........

No

3

*

Yes


Table 17 illustrates a restriction table that permits one number in an area code but restricts all other numbers in that area code.

Table 17 Restriction Table with Restricted Area Code

Preference
Call Pattern
Allowed

1

9011*

No

2

912225550150

Yes

3

91222.......

No

4

*

Yes


SMTP server setup—Sending notifications to a subscriber's e-mail or text messages to text pagers requires an SMTP server. The administrator must configure an external SMTP server address for Cisco Unity Express to use to send the text notifications. The SMTP server address can be the hostname or IP address. To use the hostname, verify that the DNS server is configured.

If the SMTP server requires a user ID and password for authentication, the administrator must configure the user ID and password on Cisco Unity Express software.

From address for outgoing e-mails—E-mail messages and notifications sent out by Cisco Unity Express display the address hostname@domain in the From field, where hostname is the hostname configured for Cisco Unity Express and domain is the domain name configured for Cisco Unity Express. The administrator can configure a more descriptive e-mail address to use in this field. Maximum length is 128 characters.

Subscriber and Device-Specific Settings

Subscribers are able to use the telephone user interface (TUI), graphical user interface (GUI), or VoiceView Express to specify the phone devices and numeric pagers to which message notifications will be sent. Subscribers can use only the GUI or VoiceView Express to configure e-mail inboxes or text pagers to receive notifications.

The administrator can use the GUI, VoiceView Express, or the CLI procedures in this section to configure any supported device to receive notifications.

The following settings are available for configuring message notification:

Phone number—The system dials this number when a mailbox receives a new message. The number consists only of digits 0 to 9; no other characters or pauses are permitted. Include any access codes as part of the phone number.

This setting is not available for e-mail inboxes and text pagers.

If the phone number is removed, the system disables the device.

The administrator configures a restriction table that controls what phone numbers are allowed for message notification. See "System-Wide Message Notification Settings" for information on restriction tables.

Extra digits—The system dials these digits after the phone number when the outgoing call is answered. The system treats these digits as DTMF digits from Cisco Unity Express to the called device.

The result of these digits depends on the called device. For example, the digits appear on the display of a numeric pager.

Extra digits can consist of digits 0 to 9, pound or hash (#), asterisk (*), and plus (+). The plus sign is used to insert a 1-second pause. The maximum number of extra digits is 64.

This setting is not available for e-mail inboxes or text pagers.

To—This setting is the e-mail address that receives the message notification. The maximum number of characters in the e-mail address is 129.

This setting is available only to e-mail inboxes and text pagers.

If the e-mail address is removed, the system disables the device.

Text—This is the content of the text message, which appears in the body of the e-mail or as a text page on the text pager. The maximum number of characters in the message is 128.

Attach to e-mail—If this setting is enabled, the system attaches a new voice message as a .wav file to the message notification e-mail. The .wav file format is G711 mu-law 8KHz 8-bit mono.

This setting is available only to e-mail inboxes.

The setting is disabled by default so that no voice messages are attached to message notifications.

The system never attaches a private message to notification e-mails, regardless of this setting.

The system-wide attachment setting takes precedence over the individual subscriber or group setting. If the administrator disables the e-mail attachment setting system-wide, then subscribers cannot enable the setting on their devices.

If the administrator changes this system-wide setting from disabled to enabled, the system does not change the preference for those subscribers or groups who were configured on an individual basis.

Enabling the device—The subscriber or administrator must enable the devices to receive message notifications. Phone devices and numeric pagers require a valid phone number to be enabled. E-mail inboxes and text pagers require a valid e-mail address to be enabled.

If the administrator changes the system-wide setting to disabled, the subscriber cannot enable any device. The subscriber can enable a device only if the system-wide setting is enabled.

Notification preference—The subscriber or administrator can set the type of messages for which notifications will be sent: all messages or urgent messages. Urgent is the default.

The system-wide attachment setting takes precedence over the individual subscriber or group setting. If the administrator changes the system-wide preference from "all" to "urgent," subscribers cannot enable the setting on their devices.

Notification schedule—The subscriber or administrator can set a schedule that activates the notification feature for a specific device. Time slots are available 24 hours a day for any day of the week in half-hour increments.

The default schedule is Monday through Friday, 8:00 am to 5:00 p.m.

If new messages arrive when the device is inactive, the system does not send a notification for them even if the messages are in a "new" state when the next active time slot occurs.

Options and Settings

Table 18 lists the settings and options available for configuring the message notification feature and whether the setting or option defines a condition for the entire system or for individual subscribers or groups. Additionally, the table indicates the interface where the settings or options can be configured.

Table 18 Message Notification Settings 

Setting or Option
Interface
System-Wide
CLI
GUI
TUI
VoiceView

Enabling notification

x

x

   

Notification preference

x

x

   

Voice message attachment

x

x

   

Connection timeout

x

x

   

Mailbox login during outcall

x

x

   

Restriction table

x

x

   

SMTP server setup

x

x

   

From-address

x

x

   
User or Group
       

Phone number

x

x

x

x

Extra digits

x

x

x

x

To

x

x

 

x

Text

x

x

 

x

Voice-mail attachment to e-mail

x

x

 

x

Enabling the device

x

x

x1

x

Notification preference

x

x

x1

x

Notification schedule

x

x

x1

x

1 Except for e-mail inboxes and text pagers.


Sending and Receiving Message Notifications

When a subscriber or GDM receives a new voice message, the system checks if message notification is enabled for that mailbox. If notification is disabled, the system does not generate any notifications.

If notification is enabled, the system checks for an enabled device and the notification schedule for that device. If the system finds an enabled device with permission to receive the notification at the time the message is received, the system sends the notification to the device. For a general delivery mailbox (GDM), the system notifies only the devices that are enabled rather than all members of the group.

Handling of the message notification depends on the device type, as described in the following sections:

Notifications to Phone Devices

Notifications to Numeric Pagers

Notifications to E-mail Inboxes

Notifications to Text Pagers

Notifications to Phone Devices

To notify a phone device, the Cisco Unity Express system calls the configured phone number.

After the subscriber answers the call, the system sends any configured extra digits. The subscriber is presented with the option to log in to the mailbox using the mailbox ID and PIN (if this option is enabled) or disable notification to the device being called.

If the subscriber does not answer the call after the configured number of seconds, or if the device is busy, the system disconnects the call and does not retry calling the subscriber.

The recipient can turn off message notification for a phone device during the notification. If the recipient does that, the system leaves a message in the recipient's mailbox stating that notification is turned off for that device.

The administrator should be aware of notification loops. For example, subscriber A configures notifications to subscriber B, subscriber B configures notifications to subscriber C, and subscriber C configures notifications to subscriber A. The notifications could fill up the subscribers' mailboxes. In such a case, the administrator should disable notification for one of the subscribers. This will stop the loop. The administrator can reenable notification for that subscriber.

Notifications to Numeric Pagers

To notify a numeric pager, the Cisco Unity Express system calls the configured phone number.

If the pager answers the call, the system sends any configured extra digits and disconnects the call. The extra digits appear on the pager display.

If the device does not answer the call after the configured number of seconds (connection timeout) or is busy, the system disconnects the call and does not retry calling the device.

Notifications to E-mail Inboxes

The system sends an e-mail message to the configured e-mail address for each new message received.


Note If no STMP server is configured, the system does not send e-mail notifications.


The subject of the e-mail message is "Message Notification." The body of the e-mail message contains the message type, extension or user ID, message sender, and the message text configured by the sender. Following is a sample e-mail message:

Message Type: Urgent
Message for: userA
Message from: userB
Meeting scheduled at 2:00 pm today in conference room 3

If the option to attach a voice message is enabled, the system attaches the message as a .wav file. The .wav file format is G711 mu-law 8KHz 8-bit mono. The filename has the format VM_yyyy.mm.dd_hh.mm.ss.wav, where yyyy is the year, dd is the day, hh is the hour in 24-hour format, mm is the minutes, and ss is the seconds.

If the system cannot deliver the e-mail, the system does not generate a message delivery failure notification.

Notifications to Text Pagers

The system sends an e-mail message to the configured e-mail address and creates one text page for each new message received.


Note If no STMP server is configured, the system does not send text pager notifications.


The subject of the e-mail message is "Message Notification." The body of the e-mail message contains the message type, extension or user ID, message sender, and the message text configured by the message recipient during notification setup. This text will be the same for all messages received by this subscriber.

Following is a sample e-mail message:

Message Type: Urgent
Message for: userA
Message from: userB
New voicemail for number 1122

If the system cannot deliver the e-mail, the system does not generate a message delivery failure notification.

Configuring System-Wide Settings

Follow this procedure to set the system-wide message notification settings.

Required Data for This Procedure

User IDs or group names if a subset of subscribers or groups will have access to message notification

Notification preference

Number of seconds for the connection timeout

If you want to add phone numbers to the restriction table:

Minimum and maximum number of digits in a dial-string

At least one dial-string pattern

SMTP server hostname and authentication values (user ID and password or credential string)

From-address for outgoing e-mails

SUMMARY STEPS

1. config t

2. voicemail notification enable

If an SMTP server is not available, a message appears warning the administrator that e-mail and text pager notifications will not work.

3. (Optional) voicemail notification preference {all | urgent}

4. (Optional) voicemail notification email attach

5. (Optional) voicemail notification connect-timeout seconds

6. (Optional) voicemail notification allow-login

7. (Optional) restriction msg-notification min-digits minimum-digits

8. (Optional) restriction msg-notification max-digits maximum-digits

9. (Optional) restriction msg-notification dial-string preference preference-number pattern pattern-string {allowed | disallowed} [insert]

10. smtp server address {hostname | ip-address} authentication {none | username userid password password | credentials credential-string}

11. voicemail configuration outgoing-email from-address email-address

12. end

13. show voicemail notification

14. show voicemail notification restriction-table

15. show smtp server

16. show voicemail configuration

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

config t

Example:

se-10-0-0-0# config t

Enters configuration mode.

Step 2 

voicemail notification enable

Example:

se-10-0-0-0(config)# voicemail notification enable

Enables voice message notification on a system-wide basis. This command must be executed before enabling the feature for any subscribers or groups.

Step 3 

voicemail notification preference {all | urgent}

Example:

se-10-0-0-0(config)# voicemail notification preference all

se-10-0-0-0(config)# voicemail notification preference urgent

(Optional) Specifies the type of messages that generate notifications.

all—All messages generate notifications.

urgent—Only urgent messages generate notifications. The system-wide default is urgent.

Step 4 

voicemail notification email attach

Example:

se-10-0-0-0(config)# voicemail notification email attach

(Optional) Enables subscribers to attach voice messages to outgoing notification e-mails. The system-wide default is disabled.

Step 5 

voicemail notification connect-timeout seconds

Example:

se-10-0-0-0(config)# voicemail notification connect-timeout 60

(Optional) Specifies the number of seconds after which an outgoing message notification call is disconnected and considered a failed call. Valid values are 12 to 96. The default is 48.

This value applies only to phone devices and numeric pagers.

Step 6 

voicemail notification allow-login

Example:

se-10-0-0-0(config)# voicemail notification allow-login

(Optional) Enables a subscriber to log in to voice mail during an outgoing notification call. The default is disabled.

If enabled, the system provides the subscriber with an option to log into voice mail to retrieve the message.

Step 7 

restriction msg-notification min-digits minimum-digits

Example:

se-10-0-0-0(config)# restriction msg-notification min-digits 5

(Optional) Specifies the minimum number of digits for a notification phone number. Valid values are 1 to 30. The default is 1.

This value applies only to phone devices and numeric pagers.

Step 8 

restriction msg-notification max-digits maximum-digits

Example:

se-10-0-0-0(config)# restriction msg-notification max-digits 12

(Optional) Specifies the maximum number of digits for a restricted number. Valid values are 1 to 30. The default is 1. A system message appears if max-digits is a smaller value than min-digits.

This value applies only to phone devices and numeric pagers.

Step 9 

restriction msg-notification dial-string preference preference-number pattern pattern-string {allowed | disallowed} [insert]

Example:

se-10-0-0-0(config)# restriction msg-notification dial-string preference 2 pattern 91222* disallowed

se-10-0-0-0(config)# restriction msg-notification dial-string preference 2 pattern 91800* allowed insert

(Optional) Specifies the dial string that the system uses to verify a phone number assigned to a phone device or numeric pager. Use this command to add a new dial string to the restriction table or to modify an existing dial string.

preference-number—Order of this string in the restriction table. The system searches the strings in order of preference, starting with 1. Valid values are 1 to 10.

The default pattern * has preference 1 by default. The administrator can modify this setting.

pattern-string—Call pattern to be matched. Valid characters are digits 0 to 9, asterisk (*), or dot (.). The table accepts duplicate call patterns.

The default pattern * cannot be deleted or modified.

allowed—Permits phone numbers with this pattern to be assigned to message notification devices.

The default pattern * is allowed by default. The administrator can modify this setting.

disallowed—Prevents phone numbers with this pattern to be assigned to message notification devices.

insert—(Optional) Inserts the dial string in the proper place in the table. The system increases the preference number of existing strings appropriately. The system displays a system message if the preference number is less than 1 or greater than 10.

If insert is not used, the system replaces any existing dial string with the given preference with this new dial string. The system displays a system message if no existing dial string has the given preference.

Step 10 

smtp server address {hostname | ip-address} authentication {none | username userid password password | credentials credential-string}

Example:

se-10-0-0-0(config)# smtp server address 10.10.5.5 authentication none

se-10-0-0-0(config)# smtp server address authentication mainsmtp username server1 password pwd123

se-10-0-0-0(config)# smtp server address 172.16.1.1 
authentication credentials 3CmyKjEFhzkjd8QxCVjv552jZsjjzh3
bSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfG
WTYHfmPSd8ZZNgd

Configures an SMTP server, which is required for sending e-mail and text notifications.

hostname—Hostname of the SMTP server.

ip-address—IP address of the SMTP server.

none—Indicates that the SMTP server does not require authentication.

userid—Authentication user ID of the SMTP server.

password—Authentication password of the SMTP server.

credential-string—Authentication credential string for the SMTP server. Copy and paste this string from the running or startup configuration.

Step 11 

voicemail configuration outgoing-email from-address email-address

Example:

se-10-0-0-0(config)# voicemail configuration outgoing-email from-address companyname@mycompany.com

Configures an address to use in the From field of outgoing Cisco Unity Express e-mail messages.

email-address—Name and domain name. Maximum length is 128 characters

Step 12 

end

Exits configuration mode.

Step 13 

show voicemail notification

Example:
se-10-0-0-0# show voicemail notification

Displays the configured message notification settings.

Step 14 

show voicemail notification restriction-table

Example:

se-10-0-0-0# show voicemail notification restriction-table

Displays the configured restriction table.

Step 15 

show smtp server

Example:

se-10-0-0-0# show smtp server

Displays the SMTP server settings.

Step 16 

show voicemail configuration

Example:

se-10-0-0-0# show voicemail configuration

Displays the From address for outgoing e-mail messages.

Examples

The following is sample output for the show voicemail notification command.

se-10-0-0-0# show voicemail notification

Message Notification:          enabled
Notification Preference:       all
Connection Timeout:            60 seconds
Login to VoiceMail allowed:    no
Attach voice message:          yes

The following is sample output for the show voicemail notification restriction-table command.

se-10-0-0-0# show voicemail notification restriction-table

Restriction table:           msg-notification
Minimum digits allowed:      5
Maximum digits allowed:      18
Dial-Strings:
     Preference      Call Pattern     Allowed
      1             91222*            Yes
      2             *                 No

The following is sample output for the show smtp server command.

se-10-0-0-0# show smtp server

SMTP Server: 172.16.1.1
Authentication: Required
Username: smtp123

The following is sample output for the show voicemail configuration command:

se-10-0-0-0# show voicemail configuration

Outgoing Email From-Address:      companyname@mycompany.com

Enabling Message Notification for a Subscriber or Group

Before configuring message notification on a device for a subscriber or group, enable the message notification capability for the subscriber or group.

Starting in Cisco Unity Express configuration mode, use the following command to enable message notification:

voicemail notification owner owner-id enable

where owner-id is the username of the subscriber or groupname of the group that requires the message notification capability.

The following example enables message notification for the subscriber user5 and the group sales:


se-10-0-0-0# config t

se-10-0-0-0(config)# voicemail notification owner user5 enable

se-10-0-0-0(config)# voicemail notification owner sales enable

se-10-0-0-0(config)# end

se-10-0-0-0# 


Now configure message notification on one or more devices for the subscriber or group.

Configuring Message Notification for Devices

The following procedures configure the devices for message notification:

Configuring Message Notification for Phone Devices

Configuring Message Notification for a Numeric Pager

Configuring Message Notification for E-mail

Configuring Message Notification for a Text Pager

Configuring Message Notification for Phone Devices

Use this procedure to configure message notification for a subscriber or group phone device.

Prerequisites

Enable the message notification capability for the subscriber or group. See "Enabling Message Notification for a Subscriber or Group".

Required Data for This Procedure

Phone number

Extra digits, if any

Notification preference

Days and times when notification is active

SUMMARY STEPS

1. username username profile vm-notif-profile {cell-phone | home-phone | work-phone} phonenumber phonenumber

or

groupname groupname profile vm-notif-profile {cell-phone | home-phone | work-phone} phonenumber phonenumber

2. (Optional) username username profile vm-notif-profile {cell-phone | home-phone | work-phone} extra-digits digits

or

(Optional) groupname groupname profile vm-notif-profile {cell-phone | home-phone | work-phone} extra-digits digits

3. username username profile vm-notif-profile {cell-phone | home-phone | work-phone} enable

or

groupname groupname profile vm-notif-profile {cell-phone | home-phone | work-phone} enable

4. username username profile vm-notif-profile {cell-phone | home-phone | work-phone} preference {all | urgent}

or

groupname groupname profile vm-notif-profile {cell-phone | home-phone | work-phone} preference {all | urgent}

5. username username profile vm-notif-profile {cell-phone | home-phone | work-phone} schedule day day-of-week active from hh:mm to hh:mm

or

groupname groupname profile vm-notif-profile {cell-phone | home-phone | work-phone} schedule day day-of-week active from hh:mm to hh:mm

6. show voicemail notification owner owner-id profile

7. show voicemail notification owner owner-id {cell-phone | home-phone | work-phone}

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

username username profile vm-notif-profile {cell-phone | home-phone | work-phone} phonenumber phonenumber

or

groupname groupname profile vm-notif-profile {cell-phone | home-phone | work-phone} phonenumber phonenumber

Example:

se-10-0-0-0# username user3 profile vm-notif-profile cell-phone phonenumber 912225550150

se-10-0-0-0# username user4 profile vm-notif-profile home-phone phonenumber 912225550160

se-10-0-0-0# groupname sales profile vm-notif-profile work-phone phonenumber 912225550165

Specifies the phone number that the system dials when sending a message notification to the phone device.

username—User ID

groupname—Group ID

phonenumber—Phone number of the device. Include any access codes in the phone number. Valid characters are digits 0 to 9.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Phone number is restricted.

Step 2 

username username profile vm-notif-profile {cell-phone | home-phone | work-phone} extra-digits digits

or

groupname grouprname profile vm-notif-profile {cell-phone | home-phone | work-phone} extra-digits digits

Example:

se-10-0-0-0# username user3 profile vm-notif-profile cell-phone extra-digits 1234

se-10-0-0-0# groupname sales profile vm-notif-profile work-phone extra-digits 7675

(Optional) Enter any extra digits that should be dialed after the outgoing call is answered.

Valid values include digits 0 to 9, pound or hash (#), asterisk (*), or plus (+). The plus sign adds a 1-second pause in the number. The maximum number of digits allowed is 64.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Extra digits contain more than 64 digits.

Extra digits contain an unacceptable character.

Step 3 

username username profile vm-notif-profile {cell-phone | home-phone | work-phone} enable

or

groupname grouprname profile vm-notif-profile {cell-phone | home-phone | work-phone} enable

Example:

se-10-0-0-0# username user3 profile vm-notif-profile cell-phone enable

se-10-0-0-0# username user4 profile vm-notif-profile home-phone enable

se-10-0-0-0# groupname sales profile vm-notif-profile work-phone enable

Enables the device to receive message notifications.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Phone device does not have an assigned phone number.

Message notification is disabled system-wide.

Step 4 

username username profile vm-notif-profile {cell-phone | home-phone | work-phone} preference {all | urgent}

or

groupname groupname profile vm-notif-profile {cell-phone | home-phone | work-phone} preference {all | urgent}

Example:

se-10-0-0-0# username user3 profile vm-notif-profile cell-phone all

se-10-0-0-0# username user4 profile vm-notif-profile home-phone preference urgent

se-10-0-0-0# groupname sales profile vm-notif-profile work-phone preference all

Specifies the type of messages that generate notifications.

all—All messages generate notifications.

urgent—Only urgent messages generate notifications. The default is urgent.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

System-wide preference is set to urgent and this command tries to set the preference to all.

Step 5 

username username profile vm-notif-profile {cell-phone | home-phone | work-phone} schedule day day-of-week active from hh:mm to hh:mm

or

groupname groupname profile vm-notif-profile {cell-phone | home-phone | work-phone} schedule day day-of-week active from hh:mm to hh:mm

Example:

se-10-0-0-0# username user3 profile vm-notif-profile cell-phone schedule day 2 active from 08:00 to 11:30

se-10-0-0-0# username user3 profile vm-notif-profile cell-phone schedule day 2 active from 13:00 to 17:30

se-10-0-0-0# username user3 profile vm-notif-profile cell-phone schedule day 3 active from 08:00 to 15:00

se-10-0-0-0# username user3 profile vm-notif-profile cell-phone schedule day 6 active from 09:00 to 13:30

se-10-0-0-0# username user4 profile vm-notif-profile home-phone schedule day 2 active from 08:00 to 12:00

se-10-0-0-0# groupname sales profile vm-notif-profile work-phone schedule day 3 active from 08:00 to 18:00

se-10-0-0-0# groupname sales profile vm-notif-profile work-phone schedule day 5 active from 08:00 to 20:00

Specifies the days and times when message notification is active for this device. This operation changes only the specified time slots; the other time slots are not changed.

day-of-week—Valid values are 1 to 7, where 1 is Sunday, 2 is Monday, and so forth.

hh—Valid values are 00 to 24. Use the 24-hour clock for start and end times.

mm—Valid values are 00 or 30.

Repeat this step for each day of the week and time block that message notification is active.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Start time is later than end time.

Step 6 

show voicemail notification owner owner-id profile

Example:

se-10-0-0-0# show voicemail notification owner user3 profile

Displays the status of message notification for the subscriber or group.

Step 7 

show voicemail notification owner owner-id {cell-phone | home-phone | work-phone}

Example:

se-10-0-0-0# show notification owner user3 cell-phone

Displays the settings for the subscriber or group device.

Examples

The following is sample output for the show voicemail notification owner command.

se-10-0-0-0# show voicemail notification owner user3 profile

Message notification:     enabled
Profile:                  vm-notif-profile

The following is sample output for the show voicemail notification owner cell-phone command.

se-10-0-0-0# show voicemail notification owner user3 cell-phone

Profile:        vm-notif-profile
Device:         cell-phone
Enabled:        yes
Preference:     all
Phone/Email:    912225550150
Extra Digits:   1234
Schedule (active hours):
    Sunday       Inactive all day
    Monday       08:00 to 11:30, 13:00 to 17:30
    Tuesday      08:00 to 15:00
    Wednesday    Inactive all day
    Thursday     Inactive all day
    Friday       09:00 to 13:30
    Saturday     Inactive all day

Configuring Message Notification for a Numeric Pager

Use this procedure to configure message notification for a subscriber or group numeric pager.

Prerequisites

Enable the message notification capability for the subscriber or group. See "Enabling Message Notification for a Subscriber or Group".

Required Data for This Procedure

Phone number

Extra digits, if any

Notification preference

Days and times when notification is active

SUMMARY STEPS

1. username username profile vm-notif-profile num-pager phonenumber phonenumber

or

groupname groupname profile vm-notif-profile num-pager phonenumber phonenumber

2. (Optional) username username profile vm-notif-profile num-pager extra-digits digits

or

(Optional) groupname groupname profile vm-notif-profile num-pager extra-digits digits

3. username username profile vm-notif-profile num-pager enable

or

groupname groupname profile vm-notif-profile num-pager enable

4. username username profile vm-notif-profile num-pager preference {all | urgent}

or

groupname groupname profile vm-notif-profile num-pager preference {all | urgent}

5. username username profile vm-notif-profile num-pager schedule day day-of-week active from hh:mm to hh:mm

or

groupname groupname profile vm-notif-profile num-pager schedule day day-of-week active from hh:mm to hh:mm

6. show voicemail notification owner owner-id profile

7. show voicemail notification owner owner-id num-pager

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

username username profile vm-notif-profile num-pager phonenumber phonenumber

or

groupname groupname profile vm-notif-profile num-pager phonenumber phonenumber

Example:

se-10-0-0-0# username user5 profile vm-notif-profile num-pager phonenumber 912225550150

se-10-0-0-0# groupname techs profile vm-notif-profile num-pager phonenumber 912225550180

Specifies the phone number that the system dials when sending a message notification to the numeric pager.

username—User ID

groupname—Group ID

phonenumber—Phone number of the device. Include any access codes in the phone number. Valid characters are digits 0 to 9.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Phone number is restricted.

Step 2 

username username profile vm-notif-profile num-pager extra-digits digits

or

groupname groupname profile vm-notif-profile num-pager extra-digits digits

Example:

se-10-0-0-0# username user5 profile vm-notif-profile num-pager extra-digits 1234

se-10-0-0-0# groupname techs profile vm-notif-profile num-pager extra-digits 8282

(Optional) Enter any extra digits that should be dialed after the outgoing call is answered.

Valid values include digits 0 to 9, pound or hash (#), asterisk (*), or plus (+). The plus sign adds a 1-second pause in the number. The maximum number of digits allowed is 64.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Extra digits contain more than 64 digits.

Extra digits contain an unacceptable character.

Step 3 

username username profile vm-notif-profile num-pager enable

or

groupname groupname profile vm-notif-profile num-pager enable

Example:

se-10-0-0-0# username user5 profile vm-notif-profile num-pager enable

se-10-0-0-0# groupname techs profile vm-notif-profile num-pager enable


Enables the device to receive message notifications.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Numeric pager does not have an assigned phone number.

Message notification is disabled system-wide.

Step 4 

username username profile vm-notif-profile num-pager preference {all | urgent}

or

groupname groupname profile vm-notif-profile num-pager preference {all | urgent}

Example:

se-10-0-0-0# username user5 profile vm-notif-profile num-pager all

se-10-0-0-0# groupname techs profile vm-notif-profile num-pager urgent

Specifies the type of messages that generate notifications.

all—All messages generate notifications.

urgent—Only urgent messages generate notifications. The default is urgent.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

System-wide preference is set to urgent and this command tries to set the preference to all.

Step 5 

username username profile vm-notif-profile num-pager schedule day day-of-week active from hh:mm to hh:mm

or

groupname groupname profile vm-notif-profile num-pager schedule day day-of-week active from hh:mm to hh:mm

Example:

se-10-0-0-0# username user5 profile vm-notif-profile num-pager schedule day 2 active from 08:00 to 11:30

se-10-0-0-0# username user5 profile vm-notif-profile num-pager schedule day 2 active from 13:00 to 17:30

se-10-0-0-0# username user5 profile vm-notif-profile num-pager schedule day 3 active from 08:00 to 15:00

se-10-0-0-0# username user5 profile vm-notif-profile num-pager schedule day 6 active from 09:00 to 13:30

se-10-0-0-0# groupname techs profile vm-notif-profile num-pager schedule day 2 active from 08:00 to 17:00

se-10-0-0-0# groupname techs profile vm-notif-profile num-pager schedule day 4 active from 08:00 to 12:00

se-10-0-0-0# groupname techs profile vm-notif-profile num-pager schedule day 4 active from 13:30 to 20:00

se-10-0-0-0# groupname techs profile vm-notif-profile num-pager schedule day 6 active from 08:00 to 15:00

Specifies the days and times when message notification is active for this device. This operation changes only the specified time slots; the other time slots are not changed.

day-of-week—Valid values are 1 to 7, where 1 is Sunday, 2 is Monday, and so forth.

hh—Valid values are 00 to 24. Use the 24-hour clock for start and end times.

mm—Valid values are 00 or 30.

Repeat this step for each day of the week and time block that message notification is active.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Start time is later than end time.

Step 6 

show voicemail notification owner owner-id profile

Example:

se-10-0-0-0# show voicemail notification owner user5 profile

Displays the status of message notification for the subscriber or group.

Step 7 

show voicemail notification owner owner-id num-pager

Example:

se-10-0-0-0# show notification owner techs num-pager

Displays the settings for the subscriber or group device.

Examples

The following is sample output for the show voicemail notification owner command.

se-10-0-0-0# show voicemail notification owner user5 profile

Message notification:     enabled
Profile:                  vm-notif-profile

The following is sample output for the show voicemail notification owner num-pager command.

se-10-0-0-0# show voicemail notification owner techs num-pager

Profile:        vm-notif-profile
Device:         num-pager
Enabled:        yes
Preference:     urgent
Phone/Email:    912225550180
Extra Digits:   8282
Schedule (active hours):
    Sunday       Inactive all day
    Monday       08:00 to 17:00
    Tuesday      Inactive all day
    Wednesday    08:00 to 12:00, 13:30 to 20:00
    Thursday     Inactive all day
    Friday       08:00 to 15:00
    Saturday     Inactive all day

Configuring Message Notification for E-mail

Use this procedure to configure message notification for a subscriber or group e-mail inbox.

Prerequisites

Enable the message notification capability for the subscriber or group. See "Enabling Message Notification for a Subscriber or Group".

Required Data for This Procedure

E-mail address

Status of attaching voice messages to e-mail notifications

Message text

Notification preference

Days and times when notification is active

SUMMARY STEPS

1. username username profile vm-notif-profile email address email-address

or

groupname groupname profile vm-notif-profile email address email-address

2. username username profile vm-notif-profile email enable

or

groupname groupname profile vm-notif-profile email enable

3. (Optional) username username profile vm-notif-profile email attach

or

(Optional) groupname groupname profile vm-notif-profile email attach

4. username username profile vm-notif-profile email preference {all | urgent}

or

groupname groupname profile vm-notif-profile email preference {all | urgent}

5. username username profile vm-notif-profile email schedule day day-of-week active from hh:mm to hh:mm

or

groupname groupname profile vm-notif-profile email schedule day day-of-week active from hh:mm to hh:mm

6. username username profile vm-notif-profile email text email-text

or

groupname grouprname profile vm-notif-profile email text email-text

7. show voicemail notification owner owner-id profile

8. show voicemail notification owner owner-id email

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

username username profile vm-notif-profile email address email-address

or

groupname groupname profile vm-notif-profile email address email-address

Example:

se-10-0-0-0# username user6 profile vm-notif-profile email address user6@company.com

se-10-0-0-0# groupname mgrs profile vm-notif-profile email address mgrs@company.com

Configures the subscriber or group e-mail address for receiving message notifications.

username—User ID

groupname—Group ID

email-address—E-mail address for the user. The maximum number of alphanumeric characters in the e-mail address is 129.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

E-mail address exceeds 129 characters.

Step 2 

username username profile vm-notif-profile email enable

or

groupname groupname profile vm-notif-profile email enable

Example:

se-10-0-0-0# username user6 profile vm-notif-profile email enable

se-10-0-0-0# groupname mgrs profile vm-notif-profile email enable


Enables the device to receive message notifications.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Message notification is disabled system-wide.

SMTP server is not configured.

Step 3 

username username profile vm-notif-profile email attach

or

groupname groupname profile vm-notif-profile email attach

Example:

se-10-0-0-0# username user6 profile vm-notif-profile email attach

se-10-0-0-0# groupname mgrs profile vm-notif-profile email attach

Enables voice messages to be attached to outgoing e-mail notifications.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

E-mail attachment is disabled system-wide and this command tries to enable it.

Step 4 

username username profile vm-notif-profile email text email-text

or

groupname groupname profile vm-notif-profile email text email-text

Example:

se-10-0-0-0# username user6 profile vm-notif-profile email text "Sales meeting scheduled for 05/26/06 2:00 pm main office room A"

se-10-0-0-0# groupname mgrs profile vm-notif-profile email text "1Q06 reports due Friday by noon"

Configures the text that is appended to the outgoing e-mail message.

email-text can contain all alphanumeric characters except question mark (?). The maximum number of characters in the message is 128. Enclose the message in double quotes (" ").

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Text message is greater than 128 characters.

Step 5 

username username profile vm-notif-profile email preference {all | urgent}

or

groupname grouprname profile vm-notif-profile email preference {all | urgent}

Example:

se-10-0-0-0# username user6 profile vm-notif-profile email preference urgent

se-10-0-0-0# groupname mgrs profile vm-notify-profile email preference all

Specifies the type of messages that generate notifications.

all—All messages generate notifications.

urgent—Only urgent messages generate notifications. The default is urgent.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

System-wide preference is set to urgent and this command tries to set the preference to all.

Step 6 

username username profile vm-notif-profile email schedule day day-of-week active from hh:mm to hh:mm

or

groupname groupname profile vm-notif-profile email schedule day day-of-week active from hh:mm to hh:mm

Example:

se-10-0-0-0# username user6 profile vm-notif-profile email schedule day 2 active from 08:00 to 11:30

se-10-0-0-0# username user6 profile vm-notif-profile email schedule day 2 active from 13:00 to 17:30

se-10-0-0-0# username user6 profile vm-notif-profile email schedule day 3 active from 08:00 to 15:00

se-10-0-0-0# username user6 profile vm-notif-profile email schedule day 6 active from 09:00 to 13:30

se-10-0-0-0# groupname mgrs profile vm-notif-profile email schedule day 2 active from 08:30 to 18:00

se-10-0-0-0# groupname mgrs profile vm-notif-profile email schedule day 3 active from 12:00 to 18:00

se-10-0-0-0# groupname mgrs profile vm-notif-profile email schedule day 4 active from 09:00 to 15:00

se-10-0-0-0# groupname mgrs profile vm-notif-profile email schedule day 5 active from 07:00 to 17:00

Specifies the days and times when message notification is active for this device. This operation changes only the specified time slots; the other time slots are not changed.

day-of-week—Valid values are 1 to 7, where 1 is Sunday, 2 is Monday, and so forth.

hh—Valid values are 00 to 24. Use the 24-hour clock for start and end times.

mm—Valid values are 00 or 30.

Repeat this step for each day of the week and time block that message notification is active.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Start time is later than end time.

Step 7 

show voicemail notification owner owner-id profile

Example:

se-10-0-0-0# show voicemail notification owner user6 profile

Displays the status of message notification for the subscriber or group.

Step 8 

show voicemail notification owner owner-id email

Example:

se-10-0-0-0# show notification owner mgrs email

Displays the settings for the subscriber or group device.

Examples

The following is sample output for the show voicemail notification owner command.

se-10-0-0-0# show voicemail notification owner mgrs profile

Message notification:     enabled
Profile:                  vm-notif-profile

The following is sample output for the show voicemail notification owner email command.

se-10-0-0-0# show voicemail notification owner user6 email

Profile:        vm-notif-profile
Device:         email
Enabled:        yes
Preference:     all
Email:          mgrs@company.com
Attach VM:      yes
Schedule (active hours):
    Sunday       Inactive all day
    Monday       08:00 to 11:30, 13:00 to 17:30
    Tuesday      08:00 to 15:00
    Wednesday    Inactive all day
    Thursday     Inactive all day
    Friday       09:00 to 13:30
    Saturday     Inactive all day

Configuring Message Notification for a Text Pager

Use this procedure to configure message notification for a subscriber or group text pager.

Prerequisites

Enable the message notification capability for the subscriber or group. See "Enabling Message Notification for a Subscriber or Group".

Required Data for This Procedure

E-mail address

Message text

Notification preference

Days and times when notification is active

SUMMARY STEPS

1. username username profile vm-notif-profile text-pager address email-address

or

groupname groupname profile vm-notif-profile text-pager address email-address

2. username username profile vm-notif-profile text-pager enable

or

groupname groupname profile vm-notif-profile text-pager enable

3. username username profile vm-notif-profile text-pager preference {all | urgent}

or

groupname groupname profile vm-notif-profile text-pager preference {all | urgent}

4. username username profile vm-notif-profile text-pager schedule day day-of-week active from hh:mm to hh:mm

or

groupname groupname profile vm-notif-profile text-pager schedule day day-of-week active from hh:mm to hh:mm

5. username username profile vm-notif-profile text-pager text email-text

or

groupname groupname profile vm-notif-profile text-pager text email-text

6. show voicemail notification owner owner-id profile

7. show voicemail notification owner owner-id text-pager

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

username username profile vm-notif-profile text-pager address email-address

or

groupname groupname profile vm-notif-profile text-pager address email-address

Example:

se-10-0-0-0# username user7 profile vm-notif-profile text-pager address user3@company.com

se-10-0-0-0# groupname pubrel profile vm-notif-profile text-pager address pubrel@mycompany.com

Configures the subscriber e-mail address for receiving message notifications.

username—User ID

groupname—Group ID

email-address—E-mail address for the subscriber. The maximum number of alphanumeric characters in the e-mail address is 129.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

E-mail address exceeds 129 characters.

Step 2 

username username profile vm-notif-profile text-pager enable

or

groupname groupname profile vm-notif-profile text-pager enable

Example:

se-10-0-0-0# username user7 profile vm-notif-profile text-pager enable

se-10-0-0-0# groupname pubrel profile vm-notif-profile text-pager enable

Enables the device to receive message notifications.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Message notification is disabled system-wide.

SMTP server is not configured.

Step 3 

username username profile vm-notif-profile text-pager text email-text

or

groupname groupname profile vm-notif-profile text-pager text email-text

Example:

se-10-0-0-0# username user7 profile vm-notif-profile text-pager text "Sales meeting scheduled for 05/26/06 2:00 pm main office room A"

se-10-0-0-0# groupname pubrel profile vm-notif-profile text-pager text "Account collaterals due tomorrow by 9 am"

Configures the text that is appended to the outgoing text pager message.

email-text can contain all alphanumeric characters except question mark (?). The maximum number of characters in the message is 128. Enclose the message in double quotes (" ").

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Text message is greater than 128 characters.

Step 4 

username username profile vm-notif-profile text-pager preference {all | urgent}

or

groupname groupname profile vm-notif-profile text-pager preference {all | urgent}

Example:

se-10-0-0-0# username user7 profile vm-notif-profile text-pager preference urgent

se-10-0-0-0# groupname pubrel profile vm-notif-profile text-pager preference all

Specifies the type of messages that generate notifications.

all—All messages generate notifications.

urgent—Only urgent messages generate notifications. The default is urgent.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

System-wide preference is set to urgent and this command tries to set the preference to all.

Step 5 

username username profile vm-notif-profile text-pager schedule day day-of-week active from hh:mm to hh:mm

or

groupname groupname profile vm-notif-profile text-pager schedule day day-of-week active from hh:mm to hh:mm

Example:

se-10-0-0-0# username user7 profile vm-notif-profile text-pager schedule day 2 active from 08:00 to 11:30

se-10-0-0-0# username user7 profile vm-notif-profile text-pager schedule day 2 active from 13:00 to 17:30

se-10-0-0-0# username user7 profile vm-notif-profile text-pager schedule day 3 active from 08:00 to 15:00

se-10-0-0-0# username user7 profile vm-notif-profile text-pager schedule day 6 active from 09:00 to 13:30

se-10-0-0-0# groupname pubrel profile vm-notif-profile text-pager schedule day 2 active 08:30 to 12:00

se-10-0-0-0# groupname pubrel profile vm-notif-profile text-pager schedule day 3 active 09:00 to 17:00

se-10-0-0-0# groupname pubrel profile vm-notif-profile text-pager schedule day 5 active 13:00 to 18:00


Specifies the days and times when message notification is active for this device. This operation changes only the specified time slots; the other time slots are not changed.

day-of-week—Valid values are 1 to 7, where 1 is Sunday, 2 is Monday, and so forth.

hh—Valid values are 00 to 24. Use the 24-hour clock for start and end times.

mm—Valid values are 00 or 30.

Repeat this step for each day of the week and time block that message notification is active.

System messages occur for the following conditions:

Username or groupname does not exist.

User or group does not have a mailbox.

Profile does not exist.

Start time is later than end time.

Step 6 

show voicemail notification owner owner-id profile

Example:

se-10-0-0-0# show voicemail notification owner user7 profile

Displays the status of message notification for the subscriber or group.

Step 7 

show voicemail notification owner owner-id text-pager

Example:

se-10-0-0-0# show notification owner pubrel text-pager

Displays the settings for the subscriber or group device.

Examples

The following is sample output for the show voicemail notification owner command.

se-10-0-0-0# show voicemail notification owner user7 profile
Message notification:     enabled
Profile:                  vm-notif-profile

The following is sample output for the show voicemail notification owner text-pager command.

se-10-0-0-0# show voicemail notification owner pubrel text-pager

Profile:        vm-notif-profile
Device:         text-pager
Enabled:        yes
Preference:     all
Email:          pubrel@company.com
Schedule (active hours):
    Sunday       Inactive all day
    Monday       08:30 to 12:00
    Tuesday      09:00 to 17:00
    Wednesday    Inactive all day
    Thursday     Inactive all day
    Friday       13:00 to 18:00
    Saturday     Inactive all day