Cisco Unity Express 2.2 System Monitoring Guide
Command Reference
Downloads: This chapterpdf (PDF - 364.0KB) | Feedback

Command Reference

Table Of Contents

Command Reference

notification security login password

notification security login user

notification security pin password

notification security pin reset

notification security pin uid

show notification configuration

show snmp configuration

snmp-server community

snmp-server contact

snmp-server enable cueShutdownRequest

snmp-server enable traps

snmp-server host

snmp-server location

trace management

trace snmp


Command Reference


notification security login password

notification security login user

notification security pin password

notification security pin reset

notification security pin uid

show notification configuration

show snmp configuration

snmp-server community

snmp-server contact

snmp-server enable cueShutdownRequest

snmp-server enable traps

snmp-server host

snmp-server location

trace management

trace snmp

notification security login password

To set the number of password failures before a notification is sent to the SNMP host, use the notification security login password command in Cisco Unity Express configuration mode. Use the no form of this command to set the threshold to the default.

notification security login password threshold

no notification security login password

Syntax Description

threshold

Number of login password failures in a 5 minute interval. Default is 30. Valid values are 0 to 999.


Defaults

30 failures

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

Use the notification security login password command to set the number of failures for login passwords in a 5-minute interval to threshold. If the number of failures exceeds this value, the system sends a notification to the SNMP host.

Examples

The following example sets the number of password errors to 3:

se-10-0-0-0# config t
se-10-0-0-0(config)# notification security login password 3
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     12    (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       3     (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

The following example resets the login threshold:

se-10-0-0-0# config t
se-10-0-0-0(config)# no notification security login password
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

Related Commands

Command
Description

notification security login user

Sets the threshold for SNMP login user failures.

notification security pin password

Sets the threshold for SNMP PIN password failures.

notification security pin reset

Sets the threshold for SNMP PIN password resets.

notification security pin uid

Sets the threshold for SNMP PIN user ID failures.

show notification configuration

Displays configured notification thresholds.


notification security login user

To set the number of login failures before a notification is sent to the SNMP host, use the notification security login user command in Cisco Unity Express configuration mode. Use the no form of this command to set the threshold to the default.

notification security login user threshold

no notification security login user

Syntax Description

threshold

Number of login failures in a 5 minute interval. Default is 30. Valid values are 0 to 999.


Defaults

30 failures

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

Use the notification security login user command to set the number of failures for login names in a 5-minute interval to threshold. If the number of failures exceeds this value, the system sends a notification to the SNMP host.

Examples

The following example sets the number of login user ID failures to 5:

se-10-0-0-0> enable
se-10-0-0-0# config t
se-10-0-0-0(config)# notification security login user 5
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         5     (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

The following example resets the login user ID threshold:

se-10-0-0-0# config t
se-10-0-0-0(config)# no notification security login user
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

Related Commands

Command
Description

notification security login password

Sets the threshold for SNMP login password failures.

notification security pin password

Sets the threshold for SNMP PIN password failures.

notification security pin reset

Sets the threshold for SNMP PIN password resets.

notification security pin uid

Sets the threshold for SNMP PIN user ID failures.

show notification configuration

Displays configured notification thresholds.


notification security pin password

To set the number of PIN password failures before a notification is sent to the SNMP host, use the notification security pin password command in Cisco Unity Express configuration mode. Use the no form of this command to set the threshold to the default.

notification security pin password threshold

no notification security pin password

Syntax Description

threshold

Number of PIN password failures in a 5 minute interval. Default is 30. Valid values are 0 to 999.


Defaults

30 failures

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

Use the notification security pin password command to set the number of PIN password failures in a 5-minute interval to threshold. If the number of failures exceeds this value, the system sends a notification to the SNMP host.

Examples

The following example sets the number of PIN password failures to 5:

se-10-0-0-0> enable
se-10-0-0-0# config t
se-10-0-0-0(config)# notification security pin password 5
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     5     (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

The following example resets the PIN password threshold:

se-10-0-0-0# config t
se-10-0-0-0(config)# no notification security pin password
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

Related Commands

Command
Description

notification security login password

Sets the threshold for SNMP login password failures.

notification security login user

Sets the threshold for SNMP login user failures.

notification security pin reset

Sets the threshold for SNMP PIN password resets.

notification security pin uid

Sets the threshold for SNMP PIN user ID failures.

show notification configuration

Displays configured notification thresholds.


notification security pin reset

To set the number of PIN resets before a notification is sent to the SNMP host, use the notification security pin reset command in Cisco Unity Express configuration mode. Use the no form of this command to set the threshold to the default.

notification security pin reset threshold

no notification security pin reset

Syntax Description

threshold

Number of PIN resets in a 5 minute interval. Default is 5. Valid values are 0 to 999.


Defaults

5 attempts

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

Use the notification security pin reset command to set the number of PIN password resets in a 5-minute interval to the threshold value. If the number of resets exceeds this value, the system sends a notification to the SNMP host.

Examples

The following example sets the number of PIN resets to 15:

se-10-0-0-0> enable
se-10-0-0-0# config t
se-10-0-0-0(config)# notification security pin reset 15
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          15    (resets within a 5 minute interval)

The following example resets the PIN reset threshold:

se-10-0-0-0# config t
se-10-0-0-0(config)# no notification security pin reset
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

Related Commands

Command
Description

notification security login password

Sets the threshold for SNMP login password failures.

notification security login user

Sets the threshold for SNMP login user failures.

notification security pin password

Sets the threshold for SNMP PIN password failures.

notification security pin uid

Sets the threshold for SNMP PIN user ID failures.

show notification configuration

Displays configured notification thresholds.


notification security pin uid

To set the number of PIN user ID failures before a notification is sent to the SNMP host, use the notification security pin uid command in Cisco Unity Express configuration mode. Use the no form of this command to set the threshold to the default.

notification security login user threshold

no notification security login user

Syntax Description

threshold

Number of PIN user ID failures in a 5 minute interval. Default is 30. Valid values are 0 to 999.


Defaults

30 failures

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

Use the notification security pin uid command to set the number of failures for PIN user IDs to threshold. If the number of failures exceeds this value, the system sends a notification to the SNMP host.

Examples

The following example sets the number of PIN user ID failures to8:

se-10-0-0-0> enable
se-10-0-0-0# config t
se-10-0-0-0(config)# notification security pin uid 8
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            8     (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

The following example resets the PIN user ID threshold:

se-10-0-0-0# config t
se-10-0-0-0(config)# no notification security pin uid
se-10-0-0-0(config)# end
se-10-0-0-0 #
se-10-0-0-0 #show notification configuration

Login user threshold:         30    (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            30    (errors within a 5 minute interval)
PIN password threshold:       30    (errors within a 5 minute interval)
PIN reset threshold:          5     (resets within a 5 minute interval)

Related Commands

Command
Description

notification security login password

Sets the threshold for SNMP login password failures.

notification security login user

Sets the threshold for SNMP login user failures.

notification security pin password

Sets the threshold for SNMP PIN password failures.

notification security pin reset

Sets the threshold for SNMP PIN password resets.

show notification configuration

Displays configured notification thresholds.


show notification configuration

To display the configured thresholds for SNMP notifications, use the show notification configuration command in Cisco Unity Express EXEC mode.

show notification configuration

Syntax Description

This command has no arguments or keywords.

Command Modes

Cisco Unity Express EXEC

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Examples

The following example shows output from the show notification configuration command:

se-10-0-0-0# show notification configuration

Login user threshold:         10    (errors within a 5 minute interval)
Login password threshold:     30    (errors within a 5 minute interval)
PIN uid threshold:            12    (errors within a 5 minute interval)
PIN password threshold:       8     (errors within a 5 minute interval)
PIN reset threshold:          3     (resets within a 5 minute interval)

Related Commands

Command
Description

notification security login password

Sets the threshold for SNMP login password failures.

notification security login user

Sets the threshold for SNMP login user failures.

notification security pin password

Sets the threshold for SNMP PIN password failures.

notification security pin reset

Sets the threshold for SNMP PIN password resets.

notification security pin uid

Sets the threshold for SNMP PIN user ID failures.

show snmp configuration

Displays the configured SNMP information.


show snmp configuration

To display the SNMP configuration parameters, use the show snmp configuration command in Cisco Unity Express EXEC mode.

show snmp configuration

Syntax Description

This command has no arguments or keywords.

Command Modes

Cisco Unity Express EXEC

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Examples

The following example shows output from the show snmp configuration command:

se-10-0-0-0# show snmp configuration

Contact:              Dial 71111 for system operator
Location:             Bldg A NYC
Community 1 RO:       nycaccess
Community 2 RO:       iminhere
Community 3 RO:       123abc
Community 1 RW:       admin_main
Community 2 RW:       myaccess
Traps:                enabled
Host Community 2:     172.16.16.224 bigtraps
cueShutdownRequest    enabled
se-10-0-0-0# 

Related Commands

Command
Description

show snmp configuration

Displays the SNMP configuration.

snmp-server contact

Specifies SNMP contact information.

snmp-server enable traps

Enables SNMP traps.

snmp-server host

Specifies up to 5 SNMP hosts.

snmp-server location

Specifies SNMP host location information.


snmp-server community

To enable SNMP and set the community string, use the snmp-server community command in Cisco Unity Express configuration mode. To remove the community string, use the no form of this command.

snmp-server community community-string {ro| rw}

no snmp-server community community-string {ro| rw}

Syntax Description

community-string

String that acts as a password and permits access to the SNMP protocol. Maximum length is 15 alphanumeric characters, including letters A to Z, letters a to z, digits 0 to 9, underscore (_), and hyphen (-). The password does not have to begin with a letter.

ro

Specifies read-only access.

rw

Specifies read-write access.


Defaults

No community strings are defined.

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

The system supports a maximum of 5 read-only community strings and 5 read-write community strings.

The no snmp-server community command disables SNMP.

Examples

The following example enables SNMP and defines two read-only and four read-write community strings.

se-10-0-0-0# config t
se-10-0-0-0(config)# snmp-server community nycaccess ro
se-10-0-0-0(config)# snmp-server community sjca_access ro
se-10-0-0-0(config)# snmp-server community nycadmin rw
se-10-0-0-0(config)# snmp-server community sj_admin rw
se-10-0-0-0(config)# snmp-server community texas_admin rw
se-10-0-0-0(config)# snmp-server community admin_main% rw
se-10-0-0-0(config)# end






The following example removes two strings:

se-10-0-0-0# config t
se-10-0-0-0(config)# no snmp-server community sjca_access ro
se-10-0-0-0(config)# no snmp-server community sj_admin rw
se-10-0-0-0(config)# end

Related Commands

Command
Description

show snmp configuration

Displays the SNMP configuration.

snmp-server contact

Specifies SNMP contact information.

snmp-server enable traps

Enables SNMP traps.

snmp-server host

Specifies up to 5 SNMP hosts.

snmp-server location

Specifies SNMP host location information.


snmp-server contact

To enter contact information for the SNMP host, which is then stored in the CISCO-UNITY-EXPRESS-MID, use the snmp-server contact command in Cisco Unity Express configuration mode. To remove the sysContact string, use the no form of this command.

snmp-server contact "contact-string"

no snmp-server contact "contact-string"

Syntax Description

"contact-string"

String that describes the system contact information. Maximum length is 31 alphanumeric characters.


Defaults

No contact string is defined.

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

This command is optional.

The string must be entered within double quotes (" ").

The contact-string value sets the sysContact string in the CISCO-UNITY-EXPRESS-MIB.

Examples

The following example defines the sysContact string.

se-10-0-0-0# config t
se-10-0-0-0(config)# snmp-server contact "Dial System Operator at ext 75555"
se-10-0-0-0(config)# end

Related Commands

Command
Description

show snmp configuration

Displays the SNMP configuration.

snmp-server community

Enables SNMP and sets community strings.

snmp-server enable traps

Enables SNMP traps.

snmp-server host

Specifies up to 5 SNMP hosts.

snmp-server location

Specifies SNMP host location information.


snmp-server enable cueShutdownRequest

To enable SNMP shutdown requests, use the snmp-server enable cueShutdownRequest command in Cisco Unity Express configuration mode. To disable the shutdown requests, use the no form of this command.

snmp-server enable cueShutdownRequest

no snmp-server enable cueShutdownRequest

Syntax Description

This command has no arguments or keywords.

Defaults

System shutdown is disabled.

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

Enabling shutdown requests allows the Cisco Unity Express module to be gracefully halted. For example, suppose an uninterruptible power supply (UPS) sends a power out alert to the Cisco Unity Express management application. The management application would send an SNMP shutdown request to bring down the Cisco Unity Express module while power is still supplied from the UPS.

For security reasons, the shutdown capability is disabled by default.

To reset the Cisco Unity Express module, use the service-module service-engine slot/port reset command on the router housing the module.

Examples

The following example enables the system shutdown capability.

se-10-0-0-0# config t
se-10-0-0-0(config)# snmp-server enable cueShutdownRequest
se-10-0-0-0(config)# end

Related Commands

Command
Description

show snmp configuration

Displays the SNMP configuration.

snmp-server community

Enables SNMP and sets community strings.

snmp-server contact

Specifies SNMP contact information.

snmp-server host

Specifies up to 5 SNMP hosts.

snmp-server location

Specifies SNMP host location information.


snmp-server enable traps

To enable SNMP traps, use the snmp-server enable traps command in Cisco Unity Express configuration mode. To disable the SNMP traps, use the no form of this command.

snmp-server enable traps

no snmp-server enable traps

Syntax Description

This command has no arguments or keywords.

Defaults

System traps are disabled.

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

The snmp-server enable traps command configures the Cisco Unity Express module to send all types of SNMP notifications to all enabled SNMP hosts. If you do not enter an snmp-server enable traps command, no notifications are sent.

Use the snmp-server enable traps command in conjunction with the snmp-server host command, which specifies a maximum of 5 hosts that receive the SNMP notifications. If no host is defined, the system discards the notifications.

Examples

The following example enables SNMP traps and specifies the SNMP host.

se-10-0-0-0# config t
se-10-0-0-0(config)# snmp-server enable traps
se-10-0-0-0(config)# snmp-server host 172.19.162.40 snmpadmin
se-10-0-0-0(config)# end

Related Commands

Command
Description

show snmp configuration

Displays the SNMP configuration.

snmp-server community

Enables SNMP and sets community strings.

snmp-server contact

Specifies SNMP contact information.

snmp-server host

Specifies up to 5 SNMP hosts.

snmp-server location

Specifies SNMP host location information.


snmp-server host

To specify at least one server to receive SNMP notifications, use the snmp-server host command in Cisco Unity Express configuration mode. To remove the specified host, use the no form of this command.

snmp-server host host-ipaddress community-string

no snmp-server host host-ipaddress

Syntax Description

host-ipaddress

IP address of the host receiving the SNMP notifications. A maximum of 5 hosts can be specified.

community-string

Password string sent with the notification operation. This string was set with the snmp-server community command.


Defaults

No host is enabled.

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

Use the snmp-server host command at least once to enable a host to receive all SNMP notifications. If no host is specified, the system discards the notifications.

Use separate snmp-server host commands for each host that receives SNMP notifications. If you issue a subsequent snmp-server host command for an existing host, the second command overwrites the first command.

No host is considered a primary host. The system sends the SNMP notifications to all enabled hosts.

Use the snmp-server host command in conjunction with the snmp-server enable traps command, which enables SNMP traps and sends the notifications to all hosts.

Examples

The following example enables SNMP traps and specifies two SNMP hosts.

se-10-0-0-0# config t
se-10-0-0-0(config)# snmp-server enable traps
se-10-0-0-0(config)# snmp-server host 172.16.40.103 sjca_access
se-10-0-0-0(config)# snmp-server host 172.16.10.5 nycaccess
se-10-0-0-0(config)# end


Related Commands

Command
Description

show snmp configuration

Displays the SNMP configuration.

snmp-server community

Enables SNMP and sets community strings.

snmp-server contact

Specifies SNMP contact information.

snmp-server enable traps

Enables SNMP traps.

snmp-server location

Specifies SNMP host location information.


snmp-server location

To enter a location description for the SNMP host, use the snmp-server location command in Cisco Unity Express configuration mode. To remove the sysLocation string, use the no form of this command.

snmp-server location "location-string"

no snmp-server location "location-string"

Syntax Description

"location-string"

String that describes the system location information. Maximum length is 31 alphanumeric characters.


Defaults

No location is defined.

Command Modes

Cisco Unity Express configuration

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

This command is optional.

The string must be entered within double quotes (" ").

The location-string value sets the sysLocation string in the CISCO-UNITY-EXPRESS-MIB.

Examples

The following example specifies the sysLocation string.

se-10-0-0-0# config t
se-10-0-0-0(config)# snmp-server location "Main St, San Jose CA"
se-10-0-0-0(config)# end

Related Commands

Command
Description

show snmp configuration

Displays the SNMP configuration.

snmp-server community

Enables SNMP and sets community strings.

snmp-server contact

Specifies SNMP contact information.

snmp-server enable traps

Enables SNMP traps.

snmp-server host

Specifies up to 5 SNMP hosts.


trace management

To enable tracing of management data requests, use the show management agent command in Cisco Unity Express EXEC mode.

trace management {agent all | agent debug | all}

Syntax Description

agent all

Enables tracing of all management data requests.

agent debug

Enables debugging of management data requests.

all

Enables tracing of all activity.


Command ModesT

Cisco Unity Express EXEC

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

As with any trace command, executing the trace management command will slow the system to some degree.

In Cisco Unity Express 2.2, the output for this command is the same for all the keywords. Use trace management all to view the management activity.

Examples

The following is sample output for the trace management command:

se-10-0-0-0# trace management agent all 
se-10-0-0-0# show trace buffer tail 

087 06/03 18:18:42.523 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.JTAPI.getJTAPConnectionStatus out 
087 06/03 18:18:42.523 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.VoiceConnectivity.getUpdateStatus in 
087 06/03 18:18:42.523 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.VoiceConnectviity.update in 
087 06/03 18:18:42.524 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.VoiceConnectivity.udpateTables in 
087 06/03 18:18:42.525 mgmt agnt 1 com.cisco.aesop.mgmt.SysdbUtil.get(/sw/protorbcp,device) 
087 06/03 18:18:42.526 mgmt agnt 1 com.cisco.aesop.mgmt.SysdbUtil.get(/hw/eth/eh0,ip,addrdefault) 
087 06/03 18:18:42.529 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.JTAPIUtil.gettapiPortStatus in 
087 06/03 18:18:42.574 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.JTAPIUtil.gettapiPortStatus {3504={id=3, 
implid=3504, state=IDLE}, 3503={id=0, implid=3503,tate=IDLE}, 3502={id=1, implid=3502, state=IDLE}, 3500={id=2, 
implid=3500, stat=IDLE}} 
087 06/03 18:18:42.574 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.JTAPIUtil.gettapiPortStatus out 
087 06/03 18:18:42.576 mgmt agnt 1 
com.cisco.aesop.mgmt.SysdbUtil.get(/sw/apps/f/ccnapps/configurations/craAesop/ccnwfapp,wfjtapi,ciscoccnatcallmanage
r) 
087 06/03 18:18:42.581 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.JTAPIUtil.getctiveCCM in 
087 06/03 18:18:42.581 mgmt agnt 1 com.cisco.aesop.mgmt.SysdbUtil.get(/sw/limit,global,applicationMode) 
087 06/03 18:18:42.602 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.JTAPIUtil.getctiveCCM out 
087 06/03 18:18:42.604 mgmt agnt 1 
com.cisco.aesop.mgmt.SysdbUtil.get(/sw/apps/f/ccnapps/configurations/craAesop/ccnwfapp,wfsip,providerHostname) 
087 06/03 18:18:42.607 mgmt agnt 1 
com.cisco.aesop.mgmt.SysdbUtil.get(/sw/apps/f/ccnapps/configurations/craAesop/ccnwfapp,wfsip,providerHostname) 
087 06/03 18:18:42.610 mgmt agnt 1 
com.cisco.aesop.mgmt.SysdbUtil.get(/sw/apps/f/ccnapps/configurations/craAesop/ccnwfapp,wfsip,providerPortnumber) 
087 06/03 18:18:42.614 mgmt agnt 1 com.cisco.aesop.mgmt.SysdbUtil.get(/sw/limit,global,applicationMode) 
087 06/03 18:18:42.615 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.VoiceConnectivity.udpateTables out 
087 06/03 18:18:42.615 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.VoiceConnectivity.update out 
087 06/03 18:18:42.616 mgmt agnt 1 com.cisco.aesop.mgmt.voicemail.VoiceConnectivity.getUpdateStatus out

Related Commands

Command
Description

notification security login password

Sets the threshold for SNMP login password failures.

notification security login user

Sets the threshold for SNMP login user failures.

notification security pin password

Sets the threshold for SNMP PIN password failures.

notification security pin reset

Sets the threshold for SNMP PIN password resets.

notification security pin uid

Sets the threshold for SNMP PIN user ID failures.

show notification configuration

Displays configured notification thresholds.


trace snmp

To enable tracing of SNMP activity, use the trace snmp agent command in Cisco Unity Express EXEC mode.

trace snmp {agent all | agent debug | all}

Syntax Description

agent all

Enables tracing of all SNMP data requests.

agent debug

Enables debugging of SNMP data requests.

all

Enables tracing of all activity.


Command ModesT

Cisco Unity Express EXEC

Command History

Cisco Unity Express Release
Modification

2.2

This command was introduced on the Cisco Unity Express NM-CUE, AIM-CUE, and NM-CUE-EC.


Usage Guidelines

As with any trace command, executing the trace snmp command will slow the system to some degree.

In Cisco Unity Express 2.2, the output for this command is the same for all the keywords. Use trace snmp all to view the SNMP activity.

Examples

The following is sample output for the trace snmp command:

e-10-0-0-0# trace snmp agent all 
se-10-0-0-0# show trace buffer tail 

4280 06/03 18:10:31.035 snmp agnt 1 
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxP
ercentTimeUsed,0) = cueMboxPercentTimeUsed 
4280 06/03 18:10:31.100 snmp agnt 1 
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfMessages,1) 
4280 06/03 18:10:31.100 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.MBeanUtil.invoke(Voicemail:name=Stats,MboxStatsTableValue,<parms>,<signature>) 
4280 06/03 18:10:31.109 snmp agnt 1 
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfMessages,1) = cueMboxNumberOfMessages 
4280 06/03 18:10:31.171 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfMessages,0) 
4280 06/03 18:10:31.171 snmp agnt 1 
com.cisco.aesop.mgmt.snmp.MBeanUtil.invoke(Voicemail:name=Stats,MboxStatsTableValue,<parms>,<signature>) 
4280 06/03 18:10:31.180 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfMessages,0) = cueMboxNumberOfMessages 
4280 06/03 18:10:31.241 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfNewMessages,1) 
4280 06/03 18:10:31.241 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.MBeanUtil.invoke(Voicemail:name=Stats,MboxStatsTableValue,<parms>,<signature>) 
4280 06/03 18:10:31.250 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfNewMessages,1) = cueMboxNumberOfNewMessages 
4280 06/03 18:10:31.313 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfNewMessages,0) 
4280 06/03 18:10:31.313 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.MBeanUtil.invoke(Voicemail:name=Stats,MboxStatsTableValue,<parms>,<signature>) 
4280 06/03 18:10:31.322 snmp agnt 1 
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfNewMessages,0) = cueMboxNumberOfNewMessages 
4280 06/03 18:10:31.384 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfSavedMessages,1) 
4280 06/03 18:10:31.385 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.MBeanUtil.invoke(Voicemail:name=Stats,MboxStatsTableValue,<parms>,<signature>) 
4280 06/03 18:10:31.393 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfSavedMessages,1) =cueMboxNumberOfSavedMessages 
4280 06/03 18:10:31.454 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfSavedMessages,0) 
4280 06/03 18:10:31.455 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.MBeanUtil.invoke(Voicemail:name=Stats,MboxStatsTableValue,<parms>,<signature>) 
4280 06/03 18:10:31.463 snmp agnt 1  
com.cisco.aesop.mgmt.snmp.SnmpNative.SnmpTableGetLong(CISCO-UNITY-EXPRESS-MIB,cueMboxTable,cueMboxN
umberOfSavedMessages,0) =cueMboxNumberOfSavedMessages 

Related Commands

Command
Description

show snmp configuration

Displays the SNMP configuration.

snmp-server community

Enables SNMP and sets community strings.

snmp-server contact

Specifies SNMP contact information.

snmp-server enable traps

Enables SNMP traps.

snmp-server host

Specifies up to 5 SNMP hosts.

snmp-server location

Specifies SNMP host location information.