Cisco Unity Express Networking with DNS-based Addressing

Available Languages

Download Options

  • PDF     (385.2 KB)
    View with Adobe Reader on a variety of devices
Updated:August 3, 2007

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Cisco Unity Express Networking with DNS-based Addressing

Table Of Contents

Cisco Unity Express Networking with DNS-based Addressing

Introduction

Prerequisites

Requirements

Components Used

Related Products

Document Conventions

Configure

Network Diagram and Environment Description

Configurations

Site 2 Configuration (Cisco 3725/Cisco CME Router)

Site 3 Configuration (Cisco 2691/Cisco CME router)

Site 4 Configuration (Cisco 3725 SRST router)

Site 6 Configuration (Cisco 3745 SRST router)

Verify

Verify DNS Server Connectivity

Verify Site-to-Site Connectivity

Verify Networking Configuration

Verify Message Send VPIM Activity

Troubleshoot

Troubleshooting Commands


Cisco Unity Express Networking with DNS-based Addressing

This document consists of the following sections:

•Introduction

•Prerequisites

•Configure

•Verify

•Troubleshoot

Introduction

This document provides a configuration example for Cisco Unity Express voice mail Voice Profile for Internet Mail (VPIM) networking between four sites. Two of the sites are Cisco Cisco CallManager Express (CME) sites, while the other two are under control of a central Cisco CallManager. Your network may be exclusively Cisco CME or exclusively Cisco CallManager. To model your network after this configuration, refer to the examples that match your intended deployment. The configuration scenario enables voice mail networking between all four sites. The configuration has the following characteristics:

•Meshed network—All sites can send and receive voice messages from all other sites. Up to 500 Cisco Unity Express sites can be meshed in a network.

•VPIM networking between the sites uses Domain Name System (DNS) addressing. You can also use direct IP addressing to set up these configurations, but that is not shown in this configuration example.

•The network defines both a four-digit and ten-digit fixed-length dialing plan. For example, IP phones at Site 2 are assigned 2001 or 2xx.yyy.2001 and 2002 or 2xx.yyy.2002; IP phones at Site 3 are are assigned 3001 or 3xx.yyy.3001 and 3002 or 3xx.yyy.3002. Refer to the "Document Conventions" section for more details about numbering and addressing used in this publication IP phones at the same site can reach each other by dialing either the four-digit or ten-digit number. Calls between IP Phones at different sites require dialing the 10-digit number. These requirements are not limitations of the products or the architecture, they are applied here to simplify the network configuration example.

•Voice mail networking between the sites is configured to use 10-digit extension addressing.

•Network location IDs for the sites are the same as the site number. For example, Site 2's location ID is 2, while Site 3's location ID is 3.

•There is no PSTN connectivity shown in the configurations of the four sites as this has no relevance to the Cisco Unity Express networking configuration. Real offices networked together include this additional component.

Prerequisites

The following sections provide information important to understand this configuration example. Read these sections before you continue with the configuration example:

•Requirements

•Components Used

•Related Products

•Document Conventions

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on these software and hardware versions:

•At Site 2, a Cisco 3725 router running Cisco CME and Cisco Unity Express

•At Site 3, a Cisco 2691 router running Cisco CME and Cisco Unity Express

•At Site 4, a Cisco 3725 router running Cisco Secure Survivable Remote Site Telephony (SRST) and Cisco Unity Express

•At Site 6, a Cisco 3725 router running Cisco SRST and Cisco Unity Express

•Cisco IOS Release 12.3(11)T

•Cisco CME 3.2

•Cisco Unity Express 2.0

•IP Voice Cisco IOS feature set

All sites are Ethernet connected to the IP network. All sites have two Cisco 7960 IP Phones. For the Cisco CME sites (Sites 2 and 3), the IP phones and dial plan is under control of Cisco CME. For the other two sites (Sites 4 and 6), the IP phones and dial plan are under control of a central Cisco CallManager and the routers are configured for SRST operation.

The information presented in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Related Products

This configuration can also be used with the following hardware and software:

•Cisco 2800 series routers

•Cisco 3800 series routers

•For Cisco 2800 series routers, Cisco IOS Release 12.3(8)T4 or later releases. For Cisco 3800 series routers, Cisco IOS Release 12.3(11)T and later releases.

Document Conventions

Where applicable, this document uses the conventions in Table 1.

Table 1 Cisco Unity Express Configuration Example Document Conventions

Convention
Description

boldfaced text

Boldfaced text is used for:

•Key and button names. (Example: Click OK.)

•Information that you enter. (Example: Enter Administrator in the User Name box.)

< > (angle brackets)

Angle brackets are used around parameters for which you supply a value. (Example: In the Command Prompt window, enter ping <IP address>.)

- (hyphen)

Hyphens separate keys that must be pressed simultaneously. (Example: Press Ctrl-Alt-Delete.)

> (right angle bracket)

A right angle bracket is used to separate selections that you make:

•On menus. (Example: On the Windows Start menu, click Settings > Control Panel > Phone and Modem Options.)

•In the navigation bar of the Cisco Unity Administrator. (Example: Go to the System > Configuration > Settings page.)

The letter a used in the high-order address range for an IP V4-formatted address.

Example: a.23.10.224

Represents a public Class A Internet address or network. Used for illustrative purposes only in order to prevent the use of public numbers.

The letters x and y used within phone numbers

Example: 2xx.yyy.1234

Represents the area code and prefix for a telephone number. Used for illustrative purposes only in order to prevent the use of public numbers.


The document also uses the following general conventions:

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the document.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Configure

In this section, you are presented with the information to configure the features described in this document.

Configuration tips:

•Make sure you can ping between sites before making calls.

•Make sure that you can make calls between sites before attempting Cisco Unity Express networking.

•Make sure you can ping between the Cisco Unity Express nodes at each site.

Network Diagram and Environment Description

This document uses the network setup shown Figure 1.

Figure 1 Network Diagram (DNS-based Addressing)

The Site 2 location uses a Cisco 3725 router with these characteristics:

•IP network access via IP address a.3.235.1

•Cisco CME configuration with 2 IP Phones, with 4-digit extensions 2001 and 2002

•Cisco CME configuration with 2 IP Phones, with 10-digit extensions 2xx.yyy.2001 and 2xx.yyy.2002

•PSTN area code 2xx

•NM-CUE

•Cisco Unity Express IP address a.3.235.128

•Network location ID 2

•Cisco Unity Express DNS domain name is ch2.cue.cisco.com

The Site 3 location uses a Cisco 2691 router with these characteristics:

•IP network access via IP address a.3.229.1

•Cisco CME configuration with 2 IP Phones, with 4-digit extensions 3001 and 3002

•Cisco CME configuration with 2 IP Phones, with 10-digit extensions 3xx.yyy.3001 and 3xx.yyy.3002

•PSTN area code 3xx

•NM-CUE

•Cisco Unity Express IP address a.3.229.128

•Network location ID 3

•Cisco Unity Express DNS domain name is ch3.cue.cisco.com

The Site 4 location uses a Cisco 3725 router with these characteristics:

•IP network access via IP address a.3.231.10

•Cisco CallManager/SRST configuration with 2 IP Phones, with 4-digit extensions 4001 and 4002

•Cisco CME configuration with 2 IP Phones, with 10-digit extensions 4xx.yyy.4001 and 4xx.yyy.4002

•PSTN area code 4xx

•NM-CUE

•Cisco Unity Express IP address a.3.231.128

•Network location ID 4

•Cisco Unity Express DNS domain name is ch4.cue.cisco.com

The Site 6 location uses a Cisco 3745 router with these characteristics:

•IP network access via IP address a.3.245.1

•Cisco CallManager/SRST configuration with 2 IP Phones, with 4-digit extensions 6001 and 6002

•Cisco CME configuration with 2 IP Phones, with 10-digit extensions 6xx.yyy.6001 and 6xx.yyy.6002

•PSTN area code 6xx

•NM-CUE

•Cisco Unity Express IP address a.3.245.128

•Network location ID 6

•Cisco Unity Express DNS domain name is ch6.cue.cisco.com

Configurations

This document uses the following configurations:

•Site 2 Configuration (Cisco 3725/Cisco CME Router))

•Site 3 Configuration (Cisco 2691/Cisco CME router)

•Site 4 Configuration (Cisco 3725 SRST router))

•Site 6 Configuration (Cisco 3745 SRST router))

Site 2 Configuration (Cisco 3725/Cisco CME Router)

Relevant extracts of the router's configuration are shown below: 

cme-3725# show running-config


Building configuration...


Current configuration : 8184 bytes

!

! Last configuration change at 11:01:46 PST Fri Nov 5 2004

! NVRAM config last updated at 08:29:05 PST Fri Nov 5 2004

!

version 12.3

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname cme-3725

!

boot-start-marker

boot system flash:c3725-ipvoice-mz.123-10.3.PI5

boot-end-marker

!

! Allow intersite H.323 calls to reach Cisco Unity Express

!         

voice service voip 

 allow-connections h323 to sip

!

!


! IP address of the router

!

interface FastEthernet0/0

 ip address a.3.235.1 255.255.0.0

 duplex auto

 speed auto

 no cdp enable

!

interface FastEthernet0/1

 ip address a.1.1.100 255.255.0.0

 speed auto

 half-duplex

 no cdp enable

!

! IP address of Cisco Unity Express

!

interface Service-Engine1/0

 ip unnumbered FastEthernet0/0

 service-module ip address a.3.235.128 255.255.0.0

 service-module ip default-gateway a.3.235.1

 hold-queue 60 out

!

ip classless

ip route a.3.235.128 255.255.255.255 Service-Engine1/0

!

! Dial-peer to allow calls to forward from Cisco CME to Cisco Unity Express

!

dial-peer voice 2100 voip

 destination-pattern 21..

 session protocol sipv2

 session target ipv4:a.3.235.128

 dtmf-relay sip-notify

 codec g711ulaw

 no vad

!

dial-peer voice 2101 voip

 description VM-AA-PSTN

 translation-profile outgoing to_cue

 destination-pattern 2xxyyy21..

 session protocol sipv2

 session target ipv4:a.3.235.128

 dtmf-relay sip-notify

 codec g711ulaw

 no vad

!

! Dial-peers to direct intersite calls

!

dial-peer voice 3000 voip

 destination-pattern 3xxyyy3...

 session target ipv4:a.3.229.1

 dtmf-relay h245-alphanumeric

 codec g711ulaw

 no vad   

!

dial-peer voice 4000 voip

 destination-pattern 4xxyyy4...

 session target ipv4:a.3.231.5

 dtmf-relay h245-alphanumeric

 codec g711ulaw

 no vad

!

dial-peer voice 6000 voip

 destination-pattern 6xxyyy6...

 session target ipv4:a.3.231.5

 dtmf-relay h245-alphanumeric

 codec g711ulaw

 no vad

!

!

telephony-service

 load 7960-7940 P00303020214

 max-ephones 50

 max-dn 120

 ip source-address a.1.1.100 port 2000

 time-format 24

 date-format dd-mm-yy

 auto assign 1 to 5

 timeouts interdigit 20

 timeouts ringing 120

 system message CME-3725

 create cnf-files version-stamp 7960 Sep 27 2004 12:31:02

 dialplan-pattern 1 2xxyyy2... extension-length 4 no-reg

 voicemail 2105

 max-conferences 8

 call-forward pattern .T

 moh music-on-hold.au

 web admin system name admin password cisco

 web admin customer name custlogin password custpswd

 dn-webedit 

 time-webedit 

 transfer-system full-consult

 transfer-pattern 3...

 transfer-pattern 2...

 directory last-name-first

!

!

! Extension definitions

!

ephone-dn  1  dual-line

 number 2001 secondary 2xxyyy2001

 label Alice

 description Alice Davidson

 name Alice Davidson

 call-forward max-length 4

 call-forward busy 2105

 call-forward noan 2105 timeout 10

!

!

ephone-dn  2  dual-line

 number 2002 secondary 2xxyyy2002

 label Aaron

 description Aaron Wilkins

 name Aaron Wilkins

 call-forward max-length 8

 call-forward busy 2105

 call-forward noan 2105 timeout 10

!

!

! Dial-peers for MWI

!

ephone-dn  51

 number 8000....

 mwi on   

!

!

ephone-dn  52

 number 8001....

 mwi off

!

!

!

! IP phone definitions

!

ephone  1

 ephone-template 1

 username "adavidson"

 mac-address 0003.6BAA.D1F8

 type 7960

 button  1:1

!

!         

!

ephone  2

 ephone-template 1

 username "awilkins"

 mac-address 0003.6BAA.D362

 type 7960

 button  1:2

Cisco Unity Express's configuration is shown below: 

cue-cme3725# show running-config


Generating configuration:


clock timezone America/Los_Angeles


hostname cue-cme3725


ip domain-name localdomain


! Definition of the DNS server

ip name-server a.3.180.50


ntp server a.3.135.1


software download server url "ftp://127.0.0.1/ftp" credentials hidden 
"6u/dKTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="


groupname Administrators create

groupname Broadcasters create

groupname Sales create


username adavidson create

username awilkins create

username acoley create

username awyant create

username amcdougal create

username admin create


groupname Sales phonenumberE164 "2xxyyy2050"

groupname Sales phonenumber "2050"


username adavidson phonenumberE164 "2xxyyy2001"

username awilkins phonenumberE164 "2xxyyy2002"

username acoley phonenumberE164 "2xxyyy2003"

username awyant phonenumberE164 "2xxyyy2004"

username amcdougal phonenumberE164 "2xxyyy2005"

username adavidson phonenumber "2001"

username awilkins phonenumber "2002"

username acoley phonenumber "2003"

username awyant phonenumber "2004"

username amcdougal phonenumber "2005"


groupname Administrators member admin

groupname Sales member acoley

groupname Sales member awilkins

groupname Administrators privilege superuser

groupname Administrators privilege ManagePrompts


backup server url "ftp://a.3.231.201/cme3725/" credentials hidden 
"1SDP4vScNKcZiym6dHQHfnl4zvlbuAn9Sd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="


ccn application autoattendant

 description "autoattendant"

 enabled

 maxsessions 8

 script "aa.aef"

 parameter "MaxRetry" "3"

 parameter "operExtn" "0"

 parameter "welcomePrompt" "AAWelcome.wav"

 end application


ccn application ciscomwiapplication

 description "ciscomwiapplication"

 enabled

 maxsessions 8

 script "setmwi.aef"

 parameter "strMWI_OFF_DN" "8001"

 parameter "strMWI_ON_DN" "8000"

 parameter "CallControlGroupID" "0"

 end application


ccn application custom-aa

 description "custom-aa"

 enabled

 maxsessions 8

 script "s1_main-officehours.aef"

 parameter "MainOperExt" "2001"

 end application


ccn application promptmgmt

 description "promptmgmt"

 enabled

 maxsessions 1

 script "promptmgmt.aef"

 end application


ccn application voicemail

 description "voicemail"

 enabled

 maxsessions 8

 script "voicebrowser.aef"

 parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"

 parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"

 end application


ccn engine

 end engine


ccn subsystem jtapi

 ccm-manager address 

 end subsystem


ccn subsystem sip

 gateway address "a.3.235.1"

 end subsystem


ccn trigger sip phonenumber 2100

 application "custom-aa"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 2102

 application "autoattendant"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 2105

 application "voicemail"

 enabled

 idletimeout 5000

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 2106

 application "promptmgmt"

 enabled

 idletimeout 5000

 locale "en_US"

 maxsessions 1

 end trigger


! Definitions of the four networking sites


network location id 2

 abbreviation "S2"

 email domain ch2.cue.cisco.com

 name "site2-cme-3725"

 end location


network location id 3

 abbreviation "S3"

 email domain ch3.cue.cisco.com

 name "site3-cme-2691"

 end location


network location id 4

 abbreviation "S4"

 email domain ch4.cue.cisco.com

 name "site4-ccm-3725"

 end location


network location id 6

 abbreviation "S6"

 email domain ch6.cue.cisco.com

 name "site6-ccm-3745"

 end location


! Definition of this site's location ID


network local location id 2


voicemail default expiration time 30

voicemail default language en_US

voicemail default mailboxsize 5520

voicemail recording time 900

voicemail default messagesize 60

voicemail operator telephone 2001

voicemail capacity time 6000

voicemail mailbox owner "Sales" size 5520

 description "Sales mailbox"

 zerooutnumber "2100"

 end mailbox


voicemail mailbox owner "acoley" size 5520

 description "acoley mailbox"

 zerooutnumber "2100"

 end mailbox


voicemail mailbox owner "adavidson" size 5520

 description "adavidson mailbox"

 zerooutnumber "2100"

 end mailbox


voicemail mailbox owner "amcdougal" size 5520

 description "amcdougal mailbox"

 zerooutnumber "2100"

 end mailbox


voicemail mailbox owner "awilkins" size 5520

 description "awilkins mailbox"

 zerooutnumber "2100"

 end mailbox


voicemail mailbox owner "awyant" size 5520

 description "awyant mailbox"

 zerooutnumber "2100"

 end mailbox

Site 3 Configuration (Cisco 2691/Cisco CME router)

Relevant extracts of the router's configuration are shown below: 

cme-2691# show running-config


Building configuration...


Current configuration : 4868 bytes

!

! Last configuration change at 07:35:10 PST Fri Oct 22 2004

! NVRAM config last updated at 12:07:37 PST Fri Oct 22 2004

!

version 12.3

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname cme-2691

!

boot-start-marker

boot system flash:c2691-ipvoice-mz.123-10.3.PI5

boot-end-marker

!

! Allow intersite H.323 calls to reach Cisco Unity Express

!

voice service voip 

 allow-connections h323 to sip

!

! IP address of the router

!         

interface FastEthernet0/0

 ip address a.3.229.1 255.255.0.0

 no ip mroute-cache

 load-interval 30

 duplex auto

 speed auto

!

interface FastEthernet0/1

 ip address a.10.1.100 255.255.0.0

 no ip mroute-cache

 duplex auto

 speed auto

!

! IP address of Cisco Unity Express

!

interface Service-Engine1/0

 ip unnumbered FastEthernet0/0

 service-module ip address a.3.229.128 255.255.0.0

 service-module ip default-gateway a.3.229.1

!

ip classless

ip route a.3.229.128 255.255.255.255 Service-Engine1/0

!

ip http server

ip http path flash:

!

! Dial-peer to allow calls to forward from Cisco CME to Cisco Unity Express

!

dial-peer voice 3100 voip

 description VM-AA

 destination-pattern 31..

 session protocol sipv2

 session target ipv4:a.3.229.128

 dtmf-relay sip-notify

 codec g711ulaw

 no vad

¡

dial-peer voice 3101 voip

 description VM-AA-PSTN

 translation-profile outgoing to_cue

 destination-pattern 3xxyyy31..

 session protocol sipv2

 session target ipv4:a.3.229.128

 dtmf-relay sip-notify

 codec g711ulaw

 no vad

!

! Dial-peers to direct intersite calls

!

!

dial-peer voice 2001 voip

 destination-pattern 2xxyyy2...

 session target ipv4:a.3.235.1

 dtmf-relay h245-alphanumeric

 codec g711ulaw

 no vad

!

dial-peer voice 4001 voip

 destination-pattern 4xxyyy4...

 session target ipv4:a.3.231.5

 dtmf-relay h245-alphanumeric

 codec g711ulaw

 no vad

!

dial-peer voice 6001 voip

 destination-pattern 6xxyyy6...

 session target ipv4:a.3.231.5

 dtmf-relay h245-alphanumeric

 codec g711ulaw

 no vad   

!

telephony-service

 load 7960-7940 P00303020214

 max-ephones 48

 max-dn 192

 ip source-address a.10.1.100 port 2000

 system message CME-2691

 create cnf-files version-stamp 7960 Jul 15 2003 13:48:12

 dialplan-pattern 1 3xxyyy3... extension-length 4 no-reg

 voicemail 3105

 max-conferences 8

 call-forward pattern .T

 web admin system name admin password cisco

 dn-webedit 

 time-webedit 

 transfer-system full-consult

 transfer-pattern 3...

 transfer-pattern 2...

!

! Extension definitions

!

ephone-dn  1  dual-line

 number 3001 secondary 3xxyyy3001

 description 3xxyyy3001

 name User1

 call-forward busy 3105

 call-forward noan 3105 timeout 10

!

!

ephone-dn  2  dual-line

 number 3002 secondary 3xxyyy3002

 description 3xxyyy3002

 name User2

 call-forward busy 3105

 call-forward noan 3105 timeout 10

!

ephone-dn  2  dual-line

 number 3002

 description User2

 name User2

 call-forward busy 3105

 call-forward noan 3105 timeout 10

!

!

! Dial-peers for MWI

!

ephone-dn  51

 number 8000....

 mwi on

!

!

ephone-dn  52

 number 8001....

 mwi off

!

! IP phone definitions

!

ephone  1

 username "User1" password null

 mac-address 0009.B7F7.5793

 button  1:1

!

!

!

ephone  2

 username "User2" password null

 mac-address 0002.FD06.D959

 button  1:2


Cisco Unity Express's configuration is shown below: 


cue-nm-2691# show running-config


Generating configuration:



clock timezone America/Los_Angeles


hostname cue-nm-2691


ip domain-name localdomain


! Definition of the DNS server

ip name-server a.3.180.50


ntp server a.3.229.1


software download server url "ftp://127.0.0.1/ftp" credentials hidden 
"6u/dKTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="


groupname Administrators create

groupname customer-service create


username admin create

username User1 create

username User2 create

username User3 create

username User4 create

username User5 create

username User6 create


groupname customer-service phonenumberE164 "4xxyyy3050"

groupname customer-service phonenumber "3050"


username User1 phonenumberE164 "3xxyyy3001"

username User2 phonenumberE164 "3xxyyy3002"

username User1 phonenumber "3001"

username User2 phonenumber "3002"

username User3 phonenumber "3003"

username User4 phonenumber "3004"

username User5 phonenumber "3005"

username User6 phonenumber "3006"


groupname Administrators member admin

groupname customer-service member User2

groupname customer-service member User3

groupname Administrators privilege superuser

groupname Administrators privilege ManagePrompts


backup server url "ftp://a.3.231.201/cme2691_4nov04/" credentials hidden 
"xxOaioWv/uC5WSZLs/L2XY/frZzvmJ2MSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="


ccn application autoattendant

 description "autoattendant"

 enabled

 maxsessions 8

 script "aa.aef"

 parameter "MaxRetry" "3"

 parameter "operExtn" "0"

 parameter "welcomePrompt" "AAgreeting.wav"

 end application


ccn application ciscomwiapplication

 description "ciscomwiapplication"

 enabled

 maxsessions 8

 script "setmwi.aef"

 parameter "strMWI_OFF_DN" "8001"

 parameter "strMWI_ON_DN" "8000"

 parameter "CallControlGroupID" "0"

 end application


ccn application promptmgmt

 description "promptmgmt"

 enabled

 maxsessions 1

 script "promptmgmt.aef"

 end application


ccn application voicemail

 description "voicemail"

 enabled

 maxsessions 8

 script "voicebrowser.aef"

 parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"

 parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"

 end application


ccn engine

 end engine


ccn subsystem jtapi

 ccm-manager address 

 end subsystem


ccn subsystem sip

 gateway address "a.3.229.1"

 end subsystem


ccn trigger sip phonenumber 3100

 application "autoattendant"

 enabled

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 3105

 application "voicemail"

 enabled

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 3106

 application "promptmgmt"

 enabled

 maxsessions 1

 end trigger


! Definitions of the four networking sites


network location id 2

 abbreviation "S2"

 email domain ch2.cue.cisco.com

 name "site2-cme-3725"

 end location


network location id 3

 abbreviation "S3"

 email domain ch3.cue.cisco.com

 name "site3-cme-2691"

 end location


network location id 4

 abbreviation "S4"

 email domain ch4.cue.cisco.com

 name "site4-ccm-3725"

 end location


network location id 6

 abbreviation "S6"

 email domain ch6.cue.cisco.com

 name "site6-ccm-3745"

 end location


! Definition of this site's location ID


network local location id 3


voicemail default expiration time 60

voicemail default language en_US

voicemail default mailboxsize 5520

voicemail recording time 900

voicemail default messagesize 60

voicemail operator telephone 0

voicemail capacity time 6000

voicemail mailbox owner "User1" size 5520

 end mailbox


voicemail mailbox owner "User2" size 5520

 end mailbox


voicemail mailbox owner "User3" size 5520

 end mailbox


voicemail mailbox owner "User4" size 5520

 end mailbox


voicemail mailbox owner "User5" size 5520

 end mailbox


voicemail mailbox owner "User6" size 5520

 end mailbox


voicemail mailbox owner "customer-service" size 5520

 description "customer-service mailbox"

 zerooutnumber "3101"

 end mailbox


end

cue-nm-2691#

Site 4 Configuration (Cisco 3725 SRST router)

Relevant extracts of the router's configuration are shown below: 

ccm_3725# show running-config


Building configuration...


Current configuration : 2278 bytes

!

! Last configuration change at 07:11:44 PST Wed Nov 10 2004

! NVRAM config last updated at 07:11:52 PST Wed Nov 10 2004

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname ccm_3725

!

boot-start-marker

boot system flash:c3725-ipvoice-mz.123-10.3.PI5

boot-end-marker

!

! Allow intersite H.323 calls to reach Cisco Unity Express during SRST

!

voice service voip 

 allow-connections h323 to sip

!


! IP address of the router

!

interface FastEthernet0/0

 ip address a.3.231.10 255.255.0.0

 speed auto

 half-duplex

!

interface FastEthernet0/1

 no ip address

 shutdown

 duplex auto

 speed auto

!

! IP address of Cisco Unity Express

!

interface Service-Engine1/0

 ip unnumbered FastEthernet0/0

 service-module ip address a.3.231.128 255.255.0.0

 service-module ip default-gateway a.3.231.10

!

ip classless

ip route a.3.231.128 255.255.255.255 Service-Engine1/0

!

ip http server

ip http path flash:

!

! Dial-peer to allow calls to forward from Cisco SRST to Cisco Unity Express

!

dial-peer voice 4100 voip

 destination-pattern 41..

 session protocol sipv2

 session target ipv4:a.3.231.128

 dtmf-relay sip-notify

 codec g711ulaw

 no vad

!

! SRST definition to ensure Cisco Unity Express and IP Phone operation during Cisco 
CallManager unavailability

!

call-manager-fallback

 max-conferences 8

 ip source-address a.3.231.5 port 2000

 max-ephones 24

 max-dn 48

 voicemail 4105

 call-forward busy 4105

 call-forward noan 4105 timeout 7


Cisco Unity Express's configuration is shown below: 

cue-ccm3725# show running-config


Generating configuration:


clock timezone America/Adak


hostname cue-ccm3725


ip domain-name localdomain


! Definition of the DNS server

ip name-server a.3.180.50



ntp server a.3.231.10


software download server url "ftp://127.0.0.1/ftp" credentials hidden 
"6u/dKTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="


groupname Administrators create


username admin create

username Bob create

username anders create

username zacks create

username Bob phonenumberE164 "4xxyyy4002"

username anders phonenumberE164 "4xxyyy4001"

username Bob phonenumber "4002"

username anders phonenumber "4001"


groupname Administrators member admin

groupname Administrators member anders

groupname Administrators privilege superuser

groupname Administrators privilege ManagePrompts


backup server url "ftp://a.3.231.244/ccm3725_8nov/" credentials hidden 
"GixGRq8cUmFqrOHVxftjAknfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="


ccn application abccorp

 description "abccorp"

 enabled

 maxsessions 8

 script "sample_aa.aef"

 parameter "prompt_ABCWelcome" "prompt_ABCWelcome.wav"

 parameter "extn_Operator" "4002"

 parameter "extn_Sales" "4002"

 parameter "prompt_Operator" "prompt_Operator.wav"

 parameter "extn_UserEntered" "2002"

 parameter "prompt_Support" "prompt_support.wav"

 parameter "prompt_Hours" "prompt_Hours.wav"

 parameter "extn_Support" "91877yyy2121"

 parameter "prompt_Extension" "prompt_Extension.wav"

 parameter "prompt_Sales" "prompt_Sales.wav"

 end application


ccn application autoattendant

 description "autoattendant"

 enabled

 maxsessions 8

 script "aa.aef"

 parameter "MaxRetry" "3"

 parameter "operExtn" "0"

 parameter "welcomePrompt" "AAWelcome.wav"

 end application


ccn application ciscomwiapplication

 description "ciscomwiapplication"

 enabled

 maxsessions 8

 script "setmwi.aef"

 parameter "strMWI_OFF_DN" "8001"

 parameter "strMWI_ON_DN" "8000"

 parameter "CallControlGroupID" "0"

 end application


ccn application promptmgmt

 description "promptmgmt"

 enabled

 maxsessions 1

 script "promptmgmt.aef"

 end application


ccn application voicemail

 description "voicemail"

 enabled

 maxsessions 8

 script "voicebrowser.aef"

 parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"

 parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"

 end application


ccn engine

 end engine


ccn subsystem jtapi

 ctiport 4901 4902 4903 4904 

 ccm-manager address a.3.231.5 

 ccm-manager credentials hidden 
"QiUfMZRFsRBqrOHVxftjAknfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="

 end subsystem


ccn subsystem sip

 gateway address "a.3.231.10"

 end subsystem


ccn trigger jtapi phonenumber 4100

 application "autoattendant"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger jtapi phonenumber 4101

 application "abccorp"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger jtapi phonenumber 4105

 application "voicemail"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger jtapi phonenumber 4106

 application "promptmgmt"

 enabled

 locale "en_US"

 maxsessions 1

 end trigger


ccn trigger sip phonenumber 4100

 application "autoattendant"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 4101

 application "abccorp"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 4105

 application "voicemail"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 4106

 application "promptmgmt"

 enabled

 locale "en_US"

 maxsessions 1

 end trigger


! Definitions of the four networking sites


network location id 2

 abbreviation "S2"

 email domain ch2.cue.cisco.com

 name "site2-cme-3725"

 end location


network location id 3

 abbreviation "S3"

 email domain ch3.cue.cisco.com

 name "site3-cme-2691"

 end location


network location id 4

 abbreviation "S4"

 email domain ch4.cue.cisco.com

 name "site4-ccm-3725"

 end location


network location id 6

 abbreviation "S6"

 email domain ch6.cue.cisco.com

 name "site6-ccm-3745"

 end location


! Definition of this site's location ID


network local location id 4


voicemail default expiration time 30

voicemail default language en_US

voicemail default mailboxsize 3000

voicemail recording time 900

voicemail default messagesize 60

voicemail operator telephone 0

voicemail capacity time 6000

voicemail mailbox owner "Bob" size 3000

 end mailbox


voicemail mailbox owner "anders" size 3000

 end mailbox


voicemail mailbox owner "zacks" size 3000

 end mailbox


end

Site 6 Configuration (Cisco 3745 SRST router)

Relevant extracts of the router's configuration are shown below: 

Relevant extracts of the router's configuration are shown below:

ccm_3745# show running-config


Building configuration...


Current configuration : 3295 bytes

!

! Last configuration change at 02:46:54 UTC Fri Apr 12 2002

! NVRAM config last updated at 17:20:53 UTC Thu Apr 11 2002

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname ccm_3745

!

boot-start-marker

boot system flash:c3745-ipvoice-mz.123-10.3.PI5

boot-end-marker

!

!

! Allow intersite H.323 calls to reach Cisco Unity Express during SRST

!

voice service voip 

 allow-connections h323 to sip

!


! IP address of the router

!

interface FastEthernet0/0

 ip address a.3.245.1 255.255.0.0

 speed auto

 half-duplex

 no mop enabled

!

interface FastEthernet0/1

 ip address 172.19.153.31 255.255.0.0

 duplex auto

 speed auto

!

! IP address of Cisco Unity Express

!

interface Service-Engine1/0

 ip unnumbered FastEthernet0/0

 service-module ip address a.3.245.128 255.255.0.0

 service-module ip default-gateway a.3.245.1

!

!

ip classless

ip route a.3.245.128 255.255.255.255 Service-Engine1/0

!

ip http server

ip http path flash:

!

!

! Dial-peer to allow calls to forward from Cisco SRST to Cisco Unity Express

!

dial-peer voice 6100 voip

 destination-pattern 61..

 session protocol sipv2

 session target ipv4:a.3.245.128

 dtmf-relay sip-notify

 codec g711ulaw

 no vad

!

! SRST definition to ensure Cisco Unity Express and IP Phone operation during Cisco 
CallManager unavailability

!

call-manager-fallback

 max-conferences 8

 ip source-address a.3.231.5 port 2000

 max-ephones 24

 max-dn 48

 voicemail 6105

 call-forward busy 6105


Cisco Unity Express's configuration is shown below: 

cue-ccm3745# show running-config


Generating configuration:



clock timezone America/Los_Angeles


hostname cue-ccm3745


ip domain-name localdomain


! Definition of the DNS server

ip name-server a.3.180.50


ntp server a.3.233.100


software download server url "ftp://127.0.0.1/ftp" credentials hidden 
"6u/dKTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="


groupname Administrators create

groupname Broadcasters create


username admin create

username Yvon create

username Zack create

username Yvon phonenumberE164 "6xxyyy6001"

username Zack phonenumberE164 "6xxyyy6002"

username Yvon phonenumber "6001"

username Zack phonenumber "6002"


groupname Administrators member admin

groupname Administrators member Yvon

groupname Administrators privilege superuser

groupname Administrators privilege ManagePrompts


backup server url "ftp://a.3.231.243/ccm3745_5nov/" credentials hidden 
"GixGRq8cUmFqrOHVxftjAknfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="


ccn application autoattendant

 description "autoattendant"

 enabled

 maxsessions 8

 script "aa.aef"

 parameter "MaxRetry" "3"

 parameter "operExtn" "0"

 parameter "welcomePrompt" "AAWelcome.wav"

 end application


ccn application ciscomwiapplication

 description "ciscomwiapplication"

 enabled

 maxsessions 8

 script "setmwi.aef"

 parameter "strMWI_OFF_DN" "8001"

 parameter "strMWI_ON_DN" "8000"

 parameter "CallControlGroupID" "0"

 end application


ccn application promptmgmt

 description "promptmgmt"

 enabled

 maxsessions 1

 script "promptmgmt.aef"

 end application


ccn application voicemail

 description "voicemail"

 enabled

 maxsessions 8

 script "voicebrowser.aef"

 parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"

 parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"

 end application


ccn engine

 end engine


ccn subsystem jtapi

 ctiport 6901 6902 6903 6904 

 ccm-manager address a.3.231.5 

 ccm-manager credentials hidden 
"1anJW38IVSZld67dzhL9pEnfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAA
AA="

 end subsystem


ccn subsystem sip

 gateway address "a.3.45.1"

 end subsystem


ccn trigger jtapi phonenumber 6100

 application "autoattendant"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger jtapi phonenumber 6105

 application "voicemail"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger jtapi phonenumber 6106

 application "promptmgmt"

 enabled

 locale "en_US"

 maxsessions 1

 end trigger


ccn trigger sip phonenumber 6100

 application "autoattendant"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 6105

 application "voicemail"

 enabled

 locale "en_US"

 maxsessions 8

 end trigger


ccn trigger sip phonenumber 6106

 application "promptmgmt"

 enabled

 locale "en_US"

 maxsessions 1

 end trigger


! Definitions of the four networking sites


network location id 2

 abbreviation "S2"

 email domain ch2.cue.cisco.com

 name "site2-cme-3725"

 end location


network location id 3

 abbreviation "S3"

 email domain ch3.cue.cisco.com

 name "site3-cme-2691"

 end location


network location id 4

 abbreviation "S4"

 email domain ch4.cue.cisco.com

 name "site4-ccm-3725"

 end location


network location id 6

 abbreviation "S6"

 email domain ch6.cue.cisco.com

 name "site6-ccm-3745"

 end location


! Definition of this site's location ID


network local location id 6


voicemail default expiration time 30

voicemail default language en_US

voicemail default mailboxsize 3000

voicemail recording time 900

voicemail default messagesize 60

voicemail operator telephone 0

voicemail capacity time 6000

voicemail mailbox owner "Yvon" size 3000

 end mailbox


voicemail mailbox owner "Zack" size 3000

 end mailbox


end

Verify

This section provides information you can use to confirm your configuration is working properly. The verification process includes:

•Verify DNS Server Connectivity)

•Verify Site-to-Site Connectivity)

•Verify Networking Configuration)

•Verify Message Send VPIM Activity)

Verify DNS Server Connectivity

This section provides instructions for verifying that your configuration works properly. Verify that you can ping between all the Cisco Unity Express locations and the DNS server.

The following is an output example for the ping command, performed on the Cisco Unity Express command-line interface (CLI) of the Site 2 system to the DNS server. Repeat this command on each Cisco Unity Express site. 

cue-cme3725# ping a.3.180.50


PING a.3.180.50 (a.3.180.50) 56(84) bytes of data.

64 bytes from a.3.180.50: icmp_seq=1 ttl=125 time=2.86 ms

64 bytes from a.3.180.50: icmp_seq=2 ttl=125 time=0.957 ms

64 bytes from a.3.180.50: icmp_seq=3 ttl=125 time=0.905 ms

64 bytes from a.3.180.50: icmp_seq=4 ttl=125 time=0.744 ms

64 bytes from a.3.180.50: icmp_seq=5 ttl=125 time=0.872 ms


--- a.3.180.50 ping statistics ---

5 packets transmitted, 5 received, 0% packet loss, time 10ms

rtt min/avg/max/mdev = 0.744/1.268/2.865/0.802 ms, ipg/ewma 2.504/2.036 ms

Verify Site-to-Site Connectivity

This section provides instructions for verifying that your configuration works properly. Verify that you can ping between all the Cisco Unity Express locations at the various sites.

The following is an output example for the ping command, performed on the Cisco Unity Express CLI of the Site 2 system to the Site 3 Cisco Unity Express. 

cue-cme3725# ping a.3.229.128


PING a.3.229.128 (a.3.229.128) 56(84) bytes of data.

64 bytes from a.3.229.128: icmp_seq=1 ttl=62 time=1.22 ms

64 bytes from a.3.229.128: icmp_seq=2 ttl=62 time=0.271 ms

64 bytes from a.3.229.128: icmp_seq=3 ttl=62 time=0.263 ms

64 bytes from a.3.229.128: icmp_seq=4 ttl=62 time=0.262 ms

64 bytes from a.3.229.128: icmp_seq=5 ttl=62 time=0.263 ms


--- a.3.229.128 ping statistics ---

5 packets transmitted, 5 received, 0% packet loss, time 4ms

rtt min/avg/max/mdev = 0.262/0.456/1.224/0.384 ms, ipg/ewma 1.094/0.827 ms

The following is an output example for the ping command, performed on the Cisco Unity Express CLI of the Site 2 system to the Site 4 Cisco Unity Express. 

cue-cme3725# ping a.3.231.128


PING a.3.231.128 (a.3.231.128) 56(84) bytes of data.

64 bytes from a.3.231.128: icmp_seq=1 ttl=62 time=1.03 ms

64 bytes from a.3.231.128: icmp_seq=2 ttl=62 time=0.262 ms

64 bytes from a.3.231.128: icmp_seq=3 ttl=62 time=0.257 ms

64 bytes from a.3.231.128: icmp_seq=4 ttl=62 time=0.256 ms

64 bytes from a.3.231.128: icmp_seq=5 ttl=62 time=0.257 ms


--- a.3.231.128 ping statistics ---

5 packets transmitted, 5 received, 0% packet loss, time 4ms

rtt min/avg/max/mdev = 0.256/0.412/1.032/0.310 ms, ipg/ewma 1.048/0.711 ms

The following is an output example for the ping command, performed on the Cisco Unity Express CLI of the Site 2 system to the Site 4 Cisco Unity Express. 

cue-cme3725# ping a.3.231.128


PING a.3.231.128 (a.3.231.128) 56(84) bytes of data.

64 bytes from a.3.231.128: icmp_seq=1 ttl=62 time=1.03 ms

64 bytes from a.3.231.128: icmp_seq=2 ttl=62 time=0.262 ms

64 bytes from a.3.231.128: icmp_seq=3 ttl=62 time=0.257 ms

64 bytes from a.3.231.128: icmp_seq=4 ttl=62 time=0.256 ms

64 bytes from a.3.231.128: icmp_seq=5 ttl=62 time=0.257 ms


--- a.3.231.128 ping statistics ---

5 packets transmitted, 5 received, 0% packet loss, time 4ms

rtt min/avg/max/mdev = 0.256/0.412/1.032/0.310 ms, ipg/ewma 1.048/0.711 ms

Verify Networking Configuration

This section provides instructions for verifying that your configuration works properly. Certain show commands are supported by the Output Interpreter Tool (registered customers only), which allows you to view an analysis of show command output. In summary, use these commands:

•show network locations

•show network detail location id <location-id>

•show network detail local location

The following is an output example for the show network locations command, performed on the Cisco Unity Express CLI of the Site 2 system. 

cue-cme3725# show network locations 


ID        NAME                               ABBREV DOMAIN

2         'site2-cme-3725'                   S2     ch2.cue.cisco.com

3         'site3-cme-2691'                   S3     ch3.cue.cisco.com

4         'site4-ccm-3725'                   S4     ch4.cue.cisco.com

6         'site6-ccm-3745'                   S6     ch6.cue.cisco.com


Local location id: 2

The following is an output example for the show network detail location id 4 command, performed on the Cisco Unity Express CLI of the Site 2 system. 

cue-cme3725# show network detail location id 4


Name:                                   site4-ccm-3725

Abbreviation:                           S4

Email domain:                           ch4.cue.cisco.com

Minimum extension length:               2

Maximum extension length:               15

Phone prefix:                           

VPIM encoding:                          dynamic

Send spoken name:                       enabled

Sent msg count:                         0

Received msg count:                     0

The following is an output example for the show network detail local command, performed on the Cisco Unity Express CLI of the Site 2 system. 

cue-cme3725# show network detail local


Location Id:                            2

Name:                                   site2-cme-3725

Abbreviation:                           S2

Email domain:                           ch2.cue.cisco.com

Minimum extension length:               2

Maximum extension length:               15

Phone prefix:                           

VPIM encoding:                          dynamic

Send spoken name:                       enabled

Verify Message Send VPIM Activity

This section provides instructions for verifying that your configuration works properly.

Certain show commands are supported by the Output Interpreter Tool (registered customers only), which allows you to view an analysis of show command output.

Send a voice message from Site 2 addressed to one or more of the other sites. The moment you hit # to send the message, enter the show network queues command on the Cisco Unity Express system of the sending system. Keep repeating the display of this command until all the VPIM messages have been sent, or until the MWI lights of the destination phones are lit.

The following is an output example for the show network queues command, performed at the Site 2 Cisco Unity Express system after sending a message from Site 2 extension 2001 addressed to Site 3 extension 3xxyyy3001, Site 4 extension 4xxyyy4001, and Site 6 extension 6xxyyy6002. 

cue-cme3725# show network queues 


Running Job Queue

=================


ID    TYPE TIME       RETRY SENDER          RECIPIENT

33    VPIM 10:22:40   0     adavidson       3xxyyy3001@ch3.cue.cisco.com

34    VPIM 10:22:40   0     adavidson       4xxyyy4001@ch4.cue.cisco.com


Urgent Job Queue

=================


ID    TYPE TIME       RETRY SENDER          RECIPIENT

No entries


Normal Job Queue

=================


ID    TYPE TIME       RETRY SENDER          RECIPIENT

35    VPIM 10:22:40   0     adavidson       6xxyyy6002@ch6.cue.cisco.com

Troubleshoot

This section provides information you can use to confirm that your configuration is working properly.

Troubleshooting Commands

The following trace commands can be issued on the sending or receiving Cisco Unity Express system to monitor SMTP and VPIM activity between them.

•trace networking smtp all—Monitors SMTP events

•trace networking vpim all—Monitors VPIM events

•show trace buffer tail—Displays contents of the trace buffer on the screen

The following is an example of output for the trace commands for the sending site (Site 3) when sending a message from Site 3 extension 3001 to Site 2 extension 2xxyyy2002. 

cue-nm-2691# trace networking smtp all

cue-nm-2691# trace networking vpim all

cue-nm-2691# show trace buffer tail


Press <CTRL-C> to exit...

7751 10/26 14:20:59.146 netw smtp 5 221 closing channel

2833 10/26 16:00:55.154 netw smtp 2

2833 10/26 16:00:55.174 netw smtp 1

8386 10/26 16:00:55.193 netw smtp 3 ch2.cue.cisco.com

8386 10/26 16:00:55.204 netw smtp 4

8386 10/26 16:00:55.218 netw smtp 6 220 ch2.cue.cisco.com Simple Mail Transfer Service 
Ready

8386 10/26 16:00:55.218 netw smtp 5 EHLO

8386 10/26 16:00:55.223 netw smtp 6 250-ch2.cue.cisco.com (Cisco Unity Express)

8386 10/26 16:00:55.224 netw smtp 6 250-X-VPIM-Wave

8386 10/26 16:00:55.225 netw smtp 6 250-X-Broadcast

8386 10/26 16:00:55.227 netw smtp 6 250-DSN NOTIFY

8386 10/26 16:00:55.229 netw smtp 6 250 SIZE

2833 10/26 16:00:55.239 netw smtp 2

8387 10/26 16:00:55.269 netw smtp 3 ch3.cue.cisco.com

2834 10/26 16:00:55.272 netw smtp 2

2834 10/26 16:00:55.276 netw smtp 3 socket hostName: cue-nm-2691.localdomain, hostAddress: 
a.3.229.128

2834 10/26 16:00:55.307 netw smtp 3 Resolved to domain: ch3.cue.cisco.com

8387 10/26 16:00:55.309 netw smtp 4

8388 10/26 16:00:55.325 netw smtp 5 Initial connection message

2834 10/26 16:00:55.328 netw smtp 1

8387 10/26 16:00:55.329 netw smtp 6 220 ch3.cue.cisco.com Simple Mail Transfer Service 
Ready

8387 10/26 16:00:55.329 netw smtp 5 EHLO

8388 10/26 16:00:55.331 netw smtp 6 UNKNOWN: EHLO ch3.cue.cisco.com

8388 10/26 16:00:55.332 netw smtp 5 250-ch3.cue.cisco.com

8387 10/26 16:00:55.332 netw smtp 6 250-ch3.cue.cisco.com (Cisco Unity Express)

8387 10/26 16:00:55.332 netw smtp 6 250-X-VPIM-Wave

8387 10/26 16:00:55.334 netw smtp 6 250-X-Broadcast

8387 10/26 16:00:55.335 netw smtp 6 250-DSN NOTIFY

8387 10/26 16:00:55.336 netw smtp 6 250 SIZE

8386 10/26 16:00:55.724 netw smtp 5 MAIL FROM 3001@ch3.cue.cisco.com

8386 10/26 16:00:55.738 netw smtp 6 250 ok

8386 10/26 16:00:55.739 netw smtp 5 RCPT TO 2xxyyy2002@ch2.cue.cisco.com

8386 10/26 16:00:55.744 netw smtp 6 250 ok

8386 10/26 16:00:55.746 netw smtp 5 DATA

8386 10/26 16:00:55.750 netw smtp 6 354 Start mail input; end with <CRLF>.<CRLF>

8386 10/26 16:00:55.755 netw vpim 3 VPIM

8386 10/26 16:00:55.775 netw vpim 3 VPIM: To: <2xxyyy2002@ch2.cue.cisco.com>

8386 10/26 16:00:55.777 netw vpim 3 VPIM: From: User One<3001@ch3.cue.cisco.com>

8386 10/26 16:00:55.779 netw vpim 3 VPIM: Date: Tue, 26 Oct 2004 16:00:54 -0700 (PDT)

8386 10/26 16:00:55.779 netw vpim 3 VPIM: MIME-Version: 1.0 (Voice 2.0)

8386 10/26 16:00:55.779 netw vpim 3 VPIM: Content-Type: Multipart/Voice-Message; 
Version=2.0;

8386 10/26 16:00:55.780 netw vpim 3 VPIM:       Boundary="==VpimMsg==1098831655752"

8386 10/26 16:00:55.780 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit

8386 10/26 16:00:55.780 netw vpim 3 VPIM: Message-ID: <1098831654914_0@ch3.cue.cisco.com>

8386 10/26 16:00:55.780 netw vpim 3 VPIM: 

8386 10/26 16:00:55.781 netw vpim 3 VPIM: --==VpimMsg==1098831655752

8386 10/26 16:00:55.782 netw vpim 3 VPIM: Content-Type: text/directory; charset=us-ascii; 
profile=vCard

8386 10/26 16:00:55.782 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit

8386 10/26 16:00:55.782 netw vpim 3 VPIM: Content-Disposition: attachment; filename="User 
One.vcf"

8386 10/26 16:00:55.782 netw vpim 3 VPIM: 

8386 10/26 16:00:55.783 netw vpim 3 VPIM: BEGIN:vCard

8386 10/26 16:00:55.783 netw vpim 3 VPIM: FN:User One

8386 10/26 16:00:55.783 netw vpim 3 VPIM: 
EMAIL;TYPE=INTERNET;TYPE=VPIM:3001@ch3.cue.cisco.com

8386 10/26 16:00:55.783 netw vpim 3 VPIM: TEL:3001

8386 10/26 16:00:55.784 netw vpim 3 VPIM: VERSION: 3.0

8386 10/26 16:00:55.784 netw vpim 3 VPIM: END:vCard

8386 10/26 16:00:55.784 netw vpim 3 VPIM: 

8387 10/26 16:00:55.843 netw smtp 5 MAIL FROM 3001@ch3.cue.cisco.com

8388 10/26 16:00:55.848 netw smtp 6 EHLO : MAIL FROM: <3001@ch3.cue.cisco.com>

8388 10/26 16:00:55.852 netw smtp 5 250 ok

8387 10/26 16:00:55.852 netw smtp 6 250 ok

8387 10/26 16:00:55.854 netw smtp 5 RCPT TO 3xxyyy3002@ch3.cue.cisco.com

8388 10/26 16:00:55.856 netw smtp 6 MAIL FROM:: RCPT TO: <3xxyyy3002@ch3.cue.cisco.com>

8388 10/26 16:00:55.856 netw smtp 5 250 ok

8387 10/26 16:00:55.856 netw smtp 6 250 ok

8387 10/26 16:00:55.858 netw smtp 5 DATA

8388 10/26 16:00:55.860 netw smtp 6 RCPT TO:: DATA

8388 10/26 16:00:55.860 netw smtp 5 354 Start data

8387 10/26 16:00:55.861 netw smtp 6 354 Start mail input; end with <CRLF>.<CRLF>

8387 10/26 16:00:55.865 netw vpim 3 VPIM

8387 10/26 16:00:55.884 netw vpim 3 VPIM: To: <3xxyyy3002@ch3.cue.cisco.com>

8387 10/26 16:00:55.885 netw vpim 3 VPIM: From: User One<3001@ch3.cue.cisco.com>

8387 10/26 16:00:55.887 netw vpim 3 VPIM: Date: Tue, 26 Oct 2004 16:00:54 -0700 (PDT)

8387 10/26 16:00:55.888 netw vpim 3 VPIM: MIME-Version: 1.0 (Voice 2.0)

8387 10/26 16:00:55.888 netw vpim 3 VPIM: Content-Type: Multipart/Voice-Message; 
Version=2.0;

8387 10/26 16:00:55.888 netw vpim 3 VPIM:       Boundary="==VpimMsg==1098831655863"

8387 10/26 16:00:55.888 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit

8387 10/26 16:00:55.889 netw vpim 3 VPIM: Message-ID: <1098831654914_0@ch3.cue.cisco.com>

8387 10/26 16:00:55.889 netw vpim 3 VPIM: 

8387 10/26 16:00:55.890 netw vpim 3 VPIM: --==VpimMsg==1098831655863

8387 10/26 16:00:55.890 netw vpim 3 VPIM: Content-Type: text/directory; charset=us-ascii; 
profile=vCard

8387 10/26 16:00:55.890 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit

8387 10/26 16:00:55.891 netw vpim 3 VPIM: Content-Disposition: attachment; filename="User 
One.vcf"

8387 10/26 16:00:55.891 netw vpim 3 VPIM: 

8387 10/26 16:00:55.891 netw vpim 3 VPIM: BEGIN:vCard

8387 10/26 16:00:55.891 netw vpim 3 VPIM: FN:User One

8387 10/26 16:00:55.891 netw vpim 3 VPIM: 
EMAIL;TYPE=INTERNET;TYPE=VPIM:3001@ch3.cue.cisco.com

8387 10/26 16:00:55.892 netw vpim 3 VPIM: TEL:3001

8387 10/26 16:00:55.892 netw vpim 3 VPIM: VERSION: 3.0

8387 10/26 16:00:55.892 netw vpim 3 VPIM: END:vCard

8387 10/26 16:00:55.892 netw vpim 3 VPIM: 

8386 10/26 16:00:55.901 netw vpim 3 VPIM: --==VpimMsg==1098831655752

8386 10/26 16:00:55.902 netw vpim 3 VPIM: Content-Type: Audio/x-wav

8386 10/26 16:00:55.906 netw vpim 3 VPIM: Content-Transfer-Encoding: Base64

8386 10/26 16:00:55.906 netw vpim 3 VPIM: Content-Disposition: inline; 
voice=Originator-Spoken-Name

8386 10/26 16:00:55.910 netw vpim 3 VPIM: 

8388 10/26 16:00:55.938 netw vpim 4 VPIM: To: <3xxyyy3002@ch3.cue.cisco.com>

8388 10/26 16:00:55.939 netw vpim 4 VPIM: From: User One<3001@ch3.cue.cisco.com>

8388 10/26 16:00:55.941 netw vpim 4 VPIM: Date: Tue, 26 Oct 2004 16:00:54 -0700 (PDT)

8388 10/26 16:00:55.943 netw vpim 4 VPIM: MIME-Version: 1.0 (Voice 2.0)

8388 10/26 16:00:55.945 netw vpim 4 VPIM: Content-Type: Multipart/Voice-Message; 
Version=2.0;Boundary="==VpimMsg==1098831655863"

8388 10/26 16:00:55.946 netw vpim 4 VPIM: Content-Transfer-Encoding: 7bit

8388 10/26 16:00:55.948 netw vpim 4 VPIM: Message-ID: <1098831654914_0@ch3.cue.cisco.com>

8388 10/26 16:00:55.949 netw vpim 4 VPIM: 

8388 10/26 16:00:55.951 netw vpim 4 VPIM: --==VpimMsg==1098831655863

8387 10/26 16:00:55.967 netw vpim 3 VPIM: --==VpimMsg==1098831655863

8387 10/26 16:00:55.967 netw vpim 3 VPIM: Content-Type: Audio/x-wav

8387 10/26 16:00:55.968 netw vpim 3 VPIM: Content-Transfer-Encoding: Base64

8387 10/26 16:00:55.968 netw vpim 3 VPIM: Content-Disposition: inline; 
voice=Originator-Spoken-Name

8387 10/26 16:00:55.968 netw vpim 3 VPIM: 

8388 10/26 16:00:55.983 netw vpim 1 Message

8388 10/26 16:00:55.986 netw vpim 4 VPIM: Content-Type: text/directory; charset=us-ascii; 
profile=vCard

8388 10/26 16:00:55.987 netw vpim 4 vCard: Content-Transfer-Encoding: 7bit

8388 10/26 16:00:55.988 netw vpim 4 vCard: Content-Disposition: attachment; filename="User 
One.vcf"

8388 10/26 16:00:55.990 netw vpim 4 vCard: 

8388 10/26 16:00:55.991 netw vpim 4 vCard: BEGIN:vCard

8388 10/26 16:00:55.992 netw vpim 4 vCard: FN:User One

8388 10/26 16:00:56.003 netw vpim 4 vCard: 
EMAIL;TYPE=INTERNET;TYPE=VPIM:3001@ch3.cue.cisco.com

8388 10/26 16:00:56.005 netw vpim 4 vCard: TEL:3001

8388 10/26 16:00:56.006 netw vpim 4 vCard: VERSION: 3.0

8388 10/26 16:00:56.007 netw vpim 4 vCard: END:vCard

8388 10/26 16:00:56.008 netw vpim 4 vCard: 

8388 10/26 16:00:56.010 netw vpim 4 vCard: --==VpimMsg==1098831655863

8388 10/26 16:00:56.012 netw vpim 4 VPIM: Content-Type: Audio/x-wav

8388 10/26 16:00:56.014 netw vpim 4 VPIM: Content-Transfer-Encoding: Base64

8388 10/26 16:00:56.015 netw vpim 4 VPIM: Content-Disposition: inline; 
voice=Originator-Spoken-Name

8388 10/26 16:00:56.020 netw vpim 5 25802

8387 10/26 16:00:56.148 netw vpim 3 VPIM: 
UklGRjI3AABXQVZFZm10IBIAAAAHAAEAQB8AAEAfAAABAAgAAABmYWN0BAAAAAA3AABkYXRhADcA

APT6/fr6+/19eXZ4e3l4eXt9/fv9fX37/f/9/f/7/X17eXt5eH37/f34+vv7+Pv/+/v7/339//99

eHh7e3l4fX3//Xt9/33///3///v6+Pb7/fv9//99/317e3t9/319/3l0eHn//3t9ff/9+Pj///r0

9vb2+/99/319/Xl2/319///9//99e//9fX19ffv/ffv//fv69vj6+vv/ff99fX12dnh5fXt9+//9

+33//f//eXh7+/39+v/9+vr6+/v9ff99//r///v9/fr7+/v/e3h5e3h2eHh5/f17//v///97//j6

       ...

The following is an example of output for the trace commands for the receiving site (Site 2) when sending a message from Site 3 extension 3001 to Site 2 extension 2xxyyy2002. 

cue-cme3725# trace networking smtp all

cue-cme3725# trace networking vpim all

cue-cme3725# show trace buffer tail


Press <CTRL-C> to exit...

9301 11/12 14:24:02.058 netw smtp 5 221 closing channel

3384 11/12 14:26:10.899 netw smtp 2

3384 11/12 14:26:10.902 netw smtp 3 socket hostName: a.3.229.128, hostAddress: a.3.229.128

3384 11/12 14:26:10.903 netw smtp 3 hostname: a.3.229.128 found in good address cache

3384 11/12 14:26:10.915 netw smtp 1

9312 11/12 14:26:10.920 netw smtp 5 Initial connection message

9312 11/12 14:26:10.926 netw smtp 6 UNKNOWN: EHLO ch3.cue.cisco.com

9312 11/12 14:26:10.926 netw smtp 5 250-ch2.cue.cisco.com

9312 11/12 14:26:11.431 netw smtp 6 EHLO : MAIL FROM: <3001@ch3.cue.cisco.com>

9312 11/12 14:26:11.437 netw smtp 5 250 ok

9312 11/12 14:26:11.446 netw smtp 6 MAIL FROM:: RCPT TO: <2xxyyy2002@ch2.cue.cisco.com>

9312 11/12 14:26:11.447 netw smtp 5 250 ok

9312 11/12 14:26:11.452 netw smtp 6 RCPT TO:: DATA

9312 11/12 14:26:11.453 netw smtp 5 354 Start data

9312 11/12 14:26:11.513 netw vpim 4 VPIM: To: <2xxyyy2002@ch2.cue.cisco.com>

9312 11/12 14:26:11.516 netw vpim 4 VPIM: From: User One<3001@ch3.cue.cisco.com>

9312 11/12 14:26:11.520 netw vpim 4 VPIM: Date: Tue, 26 Oct 2004 16:00:54 -0700 (PDT)

9312 11/12 14:26:11.524 netw vpim 4 VPIM: MIME-Version: 1.0 (Voice 2.0)

9312 11/12 14:26:11.527 netw vpim 4 VPIM: Content-Type: Multipart/Voice-Message; 
Version=2.0;Boundary="==VpimMsg==1098831655752"

9312 11/12 14:26:11.531 netw vpim 4 VPIM: Content-Transfer-Encoding: 7bit

9312 11/12 14:26:11.534 netw vpim 4 VPIM: Message-ID: <1098831654914_0@ch3.cue.cisco.com>

9312 11/12 14:26:11.537 netw vpim 4 VPIM: 

9312 11/12 14:26:11.540 netw vpim 4 VPIM: --==VpimMsg==1098831655752

9312 11/12 14:26:11.552 netw vpim 1 Message

9312 11/12 14:26:11.558 netw vpim 4 VPIM: Content-Type: text/directory; charset=us-ascii; 
profile=vCard

9312 11/12 14:26:11.561 netw vpim 4 vCard: Content-Transfer-Encoding: 7bit

9312 11/12 14:26:11.564 netw vpim 4 vCard: Content-Disposition: attachment; filename="User 
One.vcf"

9312 11/12 14:26:11.568 netw vpim 4 vCard: 

9312 11/12 14:26:11.571 netw vpim 4 vCard: BEGIN:vCard

9312 11/12 14:26:11.574 netw vpim 4 vCard: FN:User One

9312 11/12 14:26:11.577 netw vpim 4 vCard: 
EMAIL;TYPE=INTERNET;TYPE=VPIM:3001@ch3.cue.cisco.com

9312 11/12 14:26:11.580 netw vpim 4 vCard: TEL:3001

9312 11/12 14:26:11.583 netw vpim 4 vCard: VERSION: 3.0

9312 11/12 14:26:11.586 netw vpim 4 vCard: END:vCard

9312 11/12 14:26:11.589 netw vpim 4 vCard: 

9312 11/12 14:26:11.612 netw vpim 4 vCard: --==VpimMsg==1098831655752

9312 11/12 14:26:11.618 netw vpim 4 VPIM: Content-Type: Audio/x-wav

9312 11/12 14:26:11.622 netw vpim 4 VPIM: Content-Transfer-Encoding: Base64

9312 11/12 14:26:11.625 netw vpim 4 VPIM: Content-Disposition: inline; 
voice=Originator-Spoken-Name

9312 11/12 14:26:11.633 netw vpim 5 34010

9312 11/12 14:26:11.962 netw vpim 4 VPIM audio: 
UklGRjI3AABXQVZFZm10IBIAAAAHAAEAQB8AAEAfAAABAAgAAABmYWN0BAAAAAA3AABkYXRhADcA

9312 11/12 14:26:11.963 netw vpim 4 VPIM audio: 
APT6/fr6+/19eXZ4e3l4eXt9/fv9fX37/f/9/f/7/X17eXt5eH37/f34+vv7+Pv/+/v7/339//99

9312 11/12 14:26:11.965 netw vpim 4 VPIM audio: 
eHh7e3l4fX3//Xt9/33///3///v6+Pb7/fv9//99/317e3t9/319/3l0eHn//3t9ff/9+Pj///r0

9312 11/12 14:26:11.967 netw vpim 4 VPIM audio: 
9vb2+/99/319/Xl2/319///9//99e//9fX19ffv/ffv//fv69vj6+vv/ff99fX12dnh5fXt9+//9

9312 11/12 14:26:11.968 netw vpim 4 VPIM audio: 
+33//f//eXh7+/39+v/9+vr6+/v9ff99//r///v9/fr7+/v/e3h5e3h2eHh5/f17//v///97//j6

...

Was this Document Helpful?

FeedbackFeedback

Contact Cisco

This Document Applies to These Products