Installation Guide for Cisco Unity Release 8.x in a Voice Messaging Configuration (With Microsoft Exchange and With Failover Configured)
Installing the Operating System on the Cisco Unity 8.x Server
Downloads: This chapterpdf (PDF - 148.0KB) The complete bookPDF (PDF - 3.04MB) | Feedback

Installing the Operating System on the Cisco Unity 8.x Server

Table Of Contents

Installing the Operating System on the Cisco Unity 8.x Server

Considerations for Installing Windows on the Cisco Unity 8.x Server

Configuring the RAID Arrays on the Cisco Unity 8.x Server (Selected Installations)

Installing Windows Server 2003 on the Cisco Unity 8.x Server by Using the Cisco Unity Platform Configuration Discs

Installing Windows Server 2003 on the Cisco Unity 8.x Server by Using a Retail Windows Server 2003 Disc

Creating the Partitions on the Cisco Unity 8.x Server

Adding 3GB and Userva Switches to the Boot.ini File on the Cisco Unity 8.x Server


Installing the Operating System on the Cisco Unity 8.x Server


In this chapter, you do the following tasks in the order listed:

1. Review considerations for installing Windows. See the "Considerations for Installing Windows on the Cisco Unity 8.x Server" section.

2. If you are installing Windows by using a retail Windows disc: Configure the RAID arrays. See the "Configuring the RAID Arrays on the Cisco Unity 8.x Server (Selected Installations)" section.

3. Install Windows Server 2003 by using the applicable procedure based on the considerations you reviewed in Task 1.:

Installing Windows Server 2003 on the Cisco Unity 8.x Server by Using the Cisco Unity Platform Configuration Discs

Installing Windows Server 2003 on the Cisco Unity 8.x Server by Using a Retail Windows Server 2003 Disc

4. If you installed Windows by using a retail Windows disc: Create the partitions according to the storage configuration requirements for the platform. See the "Creating the Partitions on the Cisco Unity 8.x Server" section.

If you installed Windows by using the Platform Configuration discs, partitions of the correct sizes were created automatically.

5. If the Cisco Unity server will have more than 96 ports: Add the 3GB and userva switches to the boot.ini file. See the "Adding 3GB and Userva Switches to the Boot.ini File on the Cisco Unity 8.x Server" section.

When you are finished with this chapter, return to Chapter 1, "Overview of Mandatory Tasks for Installing Cisco Unity 8.x," to continue installing the Cisco Unity system correctly.


Note The tasks in the list reference detailed instructions in the Installation Guide for Cisco Unity and in other Cisco Unity documentation. Follow the documentation for a successful installation.


Considerations for Installing Windows on the Cisco Unity 8.x Server

Note the following considerations:

The Cisco Unity Platform Configuration discs for all servers install the Windows Server 2003 Multilingual User Interface (MUI) as well as Windows in English. The MUI allows you to change the language of the Windows user interface to the other operating-system languages supported for use with Cisco Unity: French, German, and Japanese.

If you install Windows by using the Cisco Unity Platform Configuration discs or an English-language retail disc, you must install the English-language version of all third-party software on the Cisco Unity server.

The Cisco Unity Server Updates wizard, which automatically installs the latest Microsoft updates recommended for use with Cisco Unity, installs only English-language updates. You can use the Server Updates wizard to install updates only in the following cases:

You installed Windows by using the Platform Configuration discs.

You installed Windows by using an English-language retail disc, with or without the MUI.

If you install a non-English version of Windows, you cannot use the Server Updates wizard to install updates. We recommend that you download the updates from the Microsoft website and manually install them, or download and install them by using Windows Automatic Update. (For more information on Windows Automatic Update, see the "Support Policy for Windows Automatic Update" section in Supported Hardware and Software, and Support Policies for Cisco Unity. For a list of the updates currently recommended for use with Cisco Unity, see Software Installed by the Cisco Unity Server Updates Wizard. Both documents are available at http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_installation_guides_list.html.)

Configuring the RAID Arrays on the Cisco Unity 8.x Server (Selected Installations)

If you are installing Windows using the Cisco Unity Platform Configuration discs, or if you do not want to configure RAID, skip this section.

Do this section only if the system is using hardware-based RAID. Software-based RAID is not supported.

To configure the arrays, you group the physical disks into logical disks and assign a RAID type to each logical disk. The server manufacturer provides a disc that contains utilities for several setup tasks, including configuring RAID arrays. Use the disc to configure the arrays when the Cisco Unity server was not purchased from Cisco.

The following software is provided by server manufacturers:

Hewlett-Packard

Hewlett-Packard SmartStart disc

IBM

IBM ServerGuide software, which you downloaded from the IBM website when you downloaded software for the installation as described in the "Downloading Software for the Cisco Unity 8.x Installation" section on page 2-2.


The following procedure contains only general steps. For detailed instructions on using a specific array-configuration utility, see the manufacturer documentation.

To Configure the RAID Arrays by Using the Manufacturer-Provided Utility


Step 1 Start the Cisco Unity server, and insert the manufacturer disc in the DVD drive.

Step 2 On the main menu, select the array-configuration utility.

Step 3 For each logical disk needed, group physical disks of the same make and model, and assign a RAID type.

For information on the recommended RAID configuration for the server, see the Cisco Unity Supported Platforms List at http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_data_sheets_list.html.

Step 4 Follow the manufacturer instructions to complete the configuration.


Installing Windows Server 2003 on the Cisco Unity 8.x Server by Using the Cisco Unity Platform Configuration Discs

A Cisco Unity server purchased from Cisco ships with Platform Configuration discs that contain a utility to install Windows Server 2003 by restoring an image that is customized for the platform. The image includes the Windows Server 2003 components, subcomponents, and service packs that were required by the version of Cisco Unity that was shipping at the time that the Platform Configuration discs were created.

Installing Windows Server 2003 by using the Cisco Unity Platform Configuration discs reduces the Cisco Unity system installation time and ensures that the required operating system and components, drivers, and service packs are installed and configured correctly. In addition, the partitions are automatically set up.


Caution Do not attach the network cable to the server until you have installed the Microsoft service packs and updates recommended for use with Cisco Unity. The Installation Guide for Cisco Unity alerts you when to install the service packs and updates, and when to connect to the network later in the installation process.

To Install Windows Server 2003 by Using the Cisco Platform Configuration Disc (Selected Servers Only)


Step 1 Remove any devices that are connected to a USB port on the server.


Caution If you leave USB devices plugged into the server during Windows configuration, the devices may be interpreted as storage devices. As a result, Windows will not create hard-disk partitions that are required by Cisco Unity Setup, and Setup will fail.

Step 2 Start the server, and insert the Cisco Unity Platform Configuration disc in the DVD drive.

Step 3 Restart the server.

Step 4 If you are using a server manufactured by Hewlett-Packard, skip to Step 5.

If you are using a server manufactured by IBM and the following message appears:

"The ServeRAID firmware and BIOS installed on your system must be upgraded or downgraded to be compatible with the RAID drivers on the Cisco Platform Configuration disc. For information on upgrading or downgrading, see the Cisco Technical Note Upgrading or Downgrading ServeRAID Firmware and BIOS on IBM Servers on Cisco.com."

do the procedures in the tech note RAID-Controller Firmware and RAID BIOS on IBM Servers Upgrade or Downgrade Procedure at http://www.cisco.com/en/US/products/ps6509/tsd_products_support_install_and_upgrade_technotes_list.html. Then return to Step 2 of this procedure.

Step 5 If you are using a server manufactured by IBM, skip to Step 6.

If you are using a server manufactured by Hewlett-Packard, choose a language for the operating system and the locale.

The remaining Windows Server 2003 installation screens will be in English, but when the Windows installation is complete, the Windows user interface will display in the language you selected.

Step 6 Follow the on-screen prompts until you are prompted to choose a licensing mode.

Step 7 Click Per Server, and click Next.

Step 8 Enter a name for the server (netBIOS name). Use only alphabetical characters A to Z and a to z, numerical characters 0 to 9, and hyphens (-). We recommend that you assign a name with 15 or fewer characters.


Caution Using other characters in the server name is not supported by DNS.

Give each Cisco Unity server a name that is unique in the first 14 characters, or Cisco Unity will have problems communicating with the accounts that it creates. For example, the following names would cause communication problems: CiscoUnitySrvr1 and CiscoUnitySrvr2.

Step 9 Click Next.

Step 10 Enter and confirm a password for the Administrator account.


Caution If you are using a server manufactured by Hewlett-Packard and you chose a language other than English in Step 5, note that until Windows installation has finished, the keyboard layout is the English-language QWERTY keyboard layout, not the standard keyboard layout for the language you chose.

Step 11 Click Next.

Step 12 Follow the on-screen prompts until the Workgroup or Computer Domain page appears.

Step 13 Click No, This Computer Is Not on a Network, or Is on a Network without a Domain.

Step 14 Optionally, specify a different name for the workgroup.

Step 15 Click Next.

Step 16 If you are using a server manufactured by Hewlett-Packard, skip to Step 17.

If you are using a server manufactured by IBM, choose a language for the operating system and the locale.

Step 17 Restart the server.

Step 18 Wait until the Platform Configuration disc has finished running configuration scripts and automatically restarting the server. (There may be multiple automatic restarts.)


Installing Windows Server 2003 on the Cisco Unity 8.x Server by Using a Retail Windows Server 2003 Disc

The server manufacturer provides a disc that contains utilities for several setup tasks, including guiding the installation of Windows 2003 Server from a retail disc. Always use the manufacturer's guided system-setup utility to install Windows Server 2003. This ensures that the operating system and the drivers are installed and configured correctly.


Caution When installing Windows Server 2003, do not install Universal Description, Discovery, and Integration (UDDI) Services, or the Cisco Unity System Setup Assistant will fail later in the installation process.

The following software is provided by server manufacturers:

Hewlett-Packard

Hewlett-Packard SmartStart

IBM

IBM ServerGuide, which you downloaded from the IBM website when you downloaded software for the installation as described in the "Downloading Software for the Cisco Unity 8.x Installation" section on page 2-2.



Caution Do not attach the network cable to the server until you have installed the Microsoft service packs and updates recommended for use with Cisco Unity. The Installation Guide for Cisco Unity alerts you when to install the service packs and updates, and when to connect to the network later in the installation process.

To Install Windows Server 2003 by Using the Manufacturer's Guided System-Setup Utility and a Retail Windows 2003 Disc


Step 1 Start the Cisco Unity server, and insert the manufacturer disc in the DVD drive.

Step 2 Follow the on-screen prompts to install Windows Server 2003 from a retail disc.

You may be prompted to configure the RAID arrays. Note the following considerations:

If the arrays have already been configured, do not change the configuration.

If the arrays have not been configured, follow the prompts to configure them. See the manufacturer documentation.

Step 3 When applicable, make the following choices:

Specify a partition size of 24 GB for the operating system.

If you are installing Windows Server 2003 on the same partition where an operating system is already installed, select and delete that partition.

Format the operating system partition by using the NTFS file system.

For regional settings, select a locale in the Your Locale (Location) list. The locale you select must match one of the system-prompts languages that you will install for Cisco Unity. Note that Cisco Unity Setup always installs the English (United States) system prompts.

For a list of supported system-prompts languages, see the "Available Languages for Cisco Unity Components" section of System Requirements for Cisco Unity at http://www.cisco.com/en/US/docs/voice_ip_comm/unity/8x/requirements/8xcusysreq.html.


Caution If the locale you specify when you install Windows Server 2003 does not match any of the installed Cisco Unity system-prompts languages, Cisco Unity will log errors in the event log and may stop taking calls. The locale you select here must match the Cisco Unity system-prompt language exactly. For example, if you choose English (United Kingdom) for locale, you must also choose English (United Kingdom) as one of the Cisco Unity system-prompts languages. Installing the system prompts for English (Australia) will not work.

For the licensing mode, choose Per Server.

When you enter a name (netBIOS name) for the Cisco Unity server:

Give each Cisco Unity server a name that is unique in the first 14 characters, or Cisco Unity will have problems communicating with the accounts that it creates. For example, the following names would cause communication problems: CiscoUnitySrvr1 and CiscoUnitySrvr2.

Use only alphabetical characters A to Z and a to z, numerical characters 0 to 9, and hyphens (-).


Caution Using other characters in the server name is not supported by DNS.

Do not join a domain. Instead, specify a workgroup. The Installation Guide for Cisco Unity alerts you when to connect to the network and when to join a domain later in the installation process.


Creating the Partitions on the Cisco Unity 8.x Server


Note If the Cisco Unity server was purchased from Cisco, skip this section. When you installed Windows using the Cisco Unity Platform Configuration discs shipped with the server, the partitions were created automatically.


Do the following procedure to create the partitions that you identified in the "Determining the Locations for Files on the Cisco Unity 8.x Server" section on page 2-5.

To Create the Partitions


Step 1 Log on to Windows as a member of the Administrators group.

Step 2 On the Windows Start menu, click Programs > Administrative Tools > Computer Management.

Step 3 In the console tree under Storage, click Disk Management.

Step 4 Right-click the first available unallocated region of the first available logical disk, and click New Partition.

Typically, you will need to create one more partition than the number of logical disks available. After you install the operating system, the first 24 GB of the first logical disk is used for the system partition, and is given the drive letter C. You create the first extended partition by using the remaining space on the first logical disk. When you create subsequent partitions, you use the entire logical disk.

Step 5 On the New Partition Wizard welcome screen, click Next.

Step 6 Click Extended Partition, and click Next. (Do not click Primary Partition.)

Step 7 Specify to use the remaining disk space, and click Next.

Step 8 Verify the settings, and click Finish.

Step 9 In the Disk Management utility, right-click the new partition, and click New Logical Drive.

Step 10 On the Create Partition Wizard welcome screen, click Next.

Step 11 Click Logical Drive, and click Next.

Step 12 Specify to use the maximum disk space, and click Next.

Step 13 Assign a drive letter, and click Next.

Step 14 Specify the NTFS file system format, and click Next.

Step 15 Verify the settings, and click Finish.

Step 16 Repeat Step 4 through Step 15 for each partition that you have to create.


Adding 3GB and Userva Switches to the Boot.ini File on the Cisco Unity 8.x Server

If the Cisco Unity server will be configured for more than 96 voice messaging ports, do the following procedure.

To Add 3GB and Userva Switches to the Boot.ini File


Step 1 Open the c:\boot.ini file in a text editor.

Step 2 Add /3GB /userva=2800 to the line that includes WINDOWS="Microsoft Windows 2003 Server". For example:

multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Windows Server 2003, Standard" /fastdetect /NoExecute=OptOut /3GB /userva=2800

Step 3 Restart the server.