Guest

Cisco Personal Assistant

Release Notes for Cisco Security Agent for Cisco Personal Assistant, Release 1.1(3)

  • Viewing Options

  • PDF (297.0 KB)
  • Feedback
Release Notes for Cisco Security Agent for Cisco Personal Assistant, Release 1.1(3)

Table Of Contents

Release Notes for Cisco Security Agent for Cisco Personal Assistant, Release 1.1(3)

Contents

Introduction

Requirements and Supported Software

Software Requirements

Supported Optional Software

Support Policy for Optional Software

Determining the Software Version

Cisco Security Agent

Policy for Cisco Security Agent for Cisco Personal Assistant

Notes on Using Cisco Security Agent for Cisco Personal Assistant

Cisco Security Agent Service Must Be Disabled for Specific Tasks

Cisco Security Agent Taskbar Icon Available Only for First Windows Logon

Locations in Which Cisco Security Agent Logs Events

Downloading Cisco Security Agent for Cisco Personal Assistant 1.1(3)

Installing Cisco Security Agent for Cisco Personal Assistant 1.1(3)

Upgrading to Cisco Security Agent for Cisco Personal Assistant 1.1(3)

Upgrade Task List

Disabling and Re-enabling the Cisco Security Agent Service

Uninstalling Cisco Security Agent for Cisco Personal Assistant

New and Changed Functionality—Release 1.1(3)

Version 1.1(3) Compiled with Cisco Security Agent Version 4.0.3.720

Caveats

Open Caveats—Release 1.1(3)

Resolved Caveat—Release 1.1(3)

Troubleshooting

Problems with Cisco Personal Assistant or Errors from Cisco Security Agent

Second Attempt to Install Software Fails Without a Warning

Cisco Personal Assistant Documentation

Obtaining Documentation

Cisco.com

Ordering Documentation

Documentation Feedback

Obtaining Technical Assistance

Cisco Technical Support Website

Submitting a Service Request

Definitions of Service Request Severity

Obtaining Additional Publications and Information


Release Notes for Cisco Security Agent for Cisco Personal Assistant, Release 1.1(3)


Published October 1, 2004

These release notes provide download, installation, and upgrade instructions, and information on new and changed functionality, and caveats for Cisco Security Agent for Cisco Personal Assistant, Release 1.1(3).

Cisco Security Agent for Cisco Personal Assistant software is available on the Cisco Personal Assistant Crypto Software Download page at http://www.cisco.com/cgi-bin/tablebuild.pl/PA3des.

Contents

These release notes contain the following sections:

Introduction

Requirements and Supported Software

Determining the Software Version

Notes on Using Cisco Security Agent for Cisco Personal Assistant

Downloading Cisco Security Agent for Cisco Personal Assistant 1.1(3)

Installing Cisco Security Agent for Cisco Personal Assistant 1.1(3)

Upgrading to Cisco Security Agent for Cisco Personal Assistant 1.1(3)

Disabling and Re-enabling the Cisco Security Agent Service

Uninstalling Cisco Security Agent for Cisco Personal Assistant

New and Changed Functionality—Release 1.1(3)

Caveats

Troubleshooting

Cisco Personal Assistant Documentation

Obtaining Documentation

Documentation Feedback

Obtaining Technical Assistance

Obtaining Additional Publications and Information

Introduction

Cisco Security Agent for Cisco Personal Assistant is a standalone Cisco Security Agent that is provided free of charge by Cisco Systems for use with Cisco Personal Assistant servers that meet the system requirements specified in the "Requirements and Supported Software" section. The agent provides intrusion prevention, malicious mobile code protection, operating system integrity assurance, and audit log consolidation based on a tested set of security rules (policies). It controls system operations by allowing or denying selected system actions before system resources are accessed. This process occurs transparently and does not significantly affect overall system performance.


Caution Cisco Security Agent for Cisco Personal Assistant should not be viewed as providing complete security for Personal Assistant servers. Instead, it should be viewed as an additional line of defense that enhances security when used with other defenses such as virus-scanning software and a firewall.

The agent was created by using CiscoWorks Management Center for Cisco Security Agents and is based on the following Management Center for Cisco Security Agents version 4.0.3, build 720 policies:

Required Windows System Module

Common Security Module

Common Web Server Security Module

Restrictive MS IIS Module

Server Module

User Authentication Auditing Module

Virus Scanner Module

Cisco Security Agent for Cisco Personal Assistant version 1.1(3) also includes the PA Base Group Exceptions policy, which allows normal Personal Assistant operations that the other policies would not allow.

To add, delete, or view policies included in Cisco Security Agent for Cisco Personal Assistant, run CiscoWorks Management Center for Cisco Security Agents, and import the file CiscoPA-CSA-4.0.3.720-1.1.3.export. The file is available at http://www.cisco.com/cgi-bin/tablebuild.pl/PA3des.

For more information on CiscoWorks Management Center for Cisco Security Agents and on Cisco Security Agent, refer to http://www.cisco.com/en/US/products/sw/cscowork/ps5212/index.html.

Requirements and Supported Software

Software Requirements

Cisco Personal Assistant version 1.4(1) or later running on the Personal Assistant server.

Microsoft Windows 2000 Server in English running on the Personal Assistant server. Other language versions are not supported.


Note If you install Cisco Security Agent for Cisco Personal Assistant on a server running Windows in Japanese, the display of some non-ASCII characters will be corrupted.


Supported Optional Software

Only the following optional software has been qualified for use on a Personal Assistant server that is running Cisco Security Agent for Cisco Personal Assistant:

McAfee NetShield for Microsoft Windows NT and Windows 2000, version 7.0.

Windows Automatic Update. It must be configured not to automatically download updates to the Personal Assistant server.

Support Policy for Optional Software

Cisco support policy is that customers can deploy third-party software for backup, monitoring, and security, including modified CSA policies, on the Cisco Personal Assistant server. However, Cisco expects that customers (or their systems integration partners) will have tested the interoperability of such products with Personal Assistant before the products are deployed, to mitigate the risk of problems being discovered within the production environment between Personal Assistant and the third-party products loaded on the Personal Assistant server.

If a customer calls Cisco TAC with a problem, a Cisco TAC engineer may require that such third-party software be turned off or even removed from the Personal Assistant server during the course of troubleshooting. If it is determined that the interoperability between the third-party software and Personal Assistant was the root cause of the problem, then the third-party software will be required to be disabled or removed from the Personal Assistant server until such time that the interoperability issue is addressed, so that the customer can continue to have a functional Personal Assistant system.

Before installing any qualified optional service pack on the Personal Assistant server, confirm that the manufacturer of any optional software or hardware that you plan to install on the Personal Assistant server—or that is already installed—also supports the service pack for use with its product.

Determining the Software Version

This section contains procedures for determining the version in use for the following software:

Cisco Security Agent

Policy for Cisco Security Agent for Cisco Personal Assistant

Cisco Security Agent

To Determine the Cisco Security Agent Version in Use


Step 1 Start Regedit.


Caution Changing the wrong registry key or entering an incorrect value can cause the server to malfunction. Before you edit the registry, confirm that you know how to restore it if a problem occurs. (Refer to the "Restoring" topics in Registry Editor Help.) If you have any questions about changing registry key settings, contact Cisco TAC.

Step 2 If you do not have a current backup of the registry, click Registry > Export Registry File, and save the registry settings to a file.

Step 3 Expand the key
HKEY_LOCAL_MACHINE\Software\Cisco Systems, Inc.\System Info\CSA Agent\Version.

Step 4 Close Regedit.


Policy for Cisco Security Agent for Cisco Personal Assistant

To Determine the Policy Version in Use for Cisco Security Agent for Cisco Personal Assistant


Step 1 Start Regedit.


Caution Changing the wrong registry key or entering an incorrect value can cause the server to malfunction. Before you edit the registry, confirm that you know how to restore it if a problem occurs. (Refer to the "Restoring" topics in Registry Editor Help.) If you have any questions about changing registry key settings, contact Cisco TAC.

Step 2 If you do not have a current backup of the registry, click Registry > Export Registry File, and save the registry settings to a file.

Step 3 Expand the key
HKEY_LOCAL_MACHINE\Software\Cisco Systems, Inc.\System Info\PA-CSA Policy\Version.

Step 4 Close Regedit.


Notes on Using Cisco Security Agent for Cisco Personal Assistant

The following sections contain information on using Cisco Security Agent for Cisco Personal Assistant:

Cisco Security Agent Service Must Be Disabled for Specific Tasks

Cisco Security Agent Taskbar Icon Available Only for First Windows Logon

Locations in Which Cisco Security Agent Logs Events

Cisco Security Agent Service Must Be Disabled for Specific Tasks

The Cisco Security Agent service must be disabled and stopped in the following situations:

Before you install any software on the Personal Assistant server.

Before you upgrade any software, including Personal Assistant, on the Personal Assistant server. This also applies to automatic upgrades (for example, installing service packs by using group policy objects or custom scripts). Cisco Security Agent for Cisco Personal Assistant allows supported virus-scanning applications to automatically download and install upgrades to virus-scanning components.

Before you add, change, or delete values in the Windows registry.

Before you change Windows system or boot files.


Caution Do not stop the Cisco Security Agent service by using the net stop command or the Cisco Security Agent icon in the taskbar. These methods are not supported.


Caution When you disable and stop the Cisco Security Agent service, you must re-enable and start it before it can monitor the Personal Assistant server again.

For instructions on disabling and re-enabling the service, see the "Disabling and Re-enabling the Cisco Security Agent Service" section.

Cisco Security Agent Taskbar Icon Available Only for First Windows Logon

If two people log on to Windows on the Personal Assistant server—one at the server and the other by using Windows Terminal Services, or both by using Terminal Services—only the first person to log on will have access to the Cisco Security Agent icon.

Locations in Which Cisco Security Agent Logs Events

Cisco Security Agent logs events in the following three locations:

Windows application
event log

Events that are generated by Cisco Security Agent have an event source of CSAgent.

Securitylog.txt

Cisco Security Agent logs one event per line. We recommend that each administrator who logs on to the Cisco Unity server add a shortcut for Securitylog.txt to the Windows desktop. The file is located in the <InstallDirectory>\Cisco\CSAgent\Log directory.

The data in the file is in comma-separated-value format. In general, there should not be many entries in the file, so you should be able to read it in a text editor, for example, Notepad. (You might want to turn off word wrap.) If there are a lot of entries, you can view the data more easily if you copy the file to a computer on which a spreadsheet application is installed, change the filename extension from .txt to .csv, and open the file in the spreadsheet application.

CSA Control Panel

To display the CSA Control Panel, double-click the Cisco Security Agent taskbar icon, and click the Messages tab. Only events that have occurred since you logged on to Windows appear in the CSA Control Panel.


Downloading Cisco Security Agent for Cisco Personal Assistant 1.1(3)

To Download Cisco Security Agent for Cisco Personal Assistant 1.1(3)


Step 1 Confirm that the computer you are using has up to 20 MB of hard-disk space for the download file and the installed files.

Step 2 On a computer with a high-speed Internet connection, go to the Cisco Personal Assistant Crypto Software Download page at http://www.cisco.com/cgi-bin/tablebuild.pl/PA3des.


Note To access the software download page, you must be logged on to Cisco.com as a registered user.


Because of export controls on strong encryption, the first time you download Cisco Security Agent for Cisco Personal Assistant, you need to fill out a brief questionnaire. Follow the on-screen prompts.

Step 3 Click CiscoPA-CSA-4.0.3.720-1.1.3-K9.exe.

Step 4 Follow the on-screen prompts to complete the download.

Step 5 If you plan to install Cisco Security Agent for Cisco Personal Assistant from a compact disc, burn the CD.


Installing Cisco Security Agent for Cisco Personal Assistant 1.1(3)


Note If you are upgrading Cisco Security Agent for Cisco Personal Assistant to version 1.1(3), see the "Upgrading to Cisco Security Agent for Cisco Personal Assistant 1.1(3)" section.


We recommend that you install Cisco Security Agent for Cisco Personal Assistant after regular business hours because the installation will affect Personal Assistant performance. In addition, when the installation completes, you must restart the Personal Assistant server for Cisco Security Agent for Cisco Personal Assistant to start working.


Caution Do not install Cisco Security Agent for Cisco Personal Assistant by using Windows Terminal Services, or the installation will fail.

To Install Cisco Security Agent for Cisco Personal Assistant 1.1(3)


Step 1 Log on to the Personal Assistant server by using an account that is a member of the Administrators group or the Local Administrators group.

Step 2 Confirm that the server has at least 20 MB of hard-disk space available for the download file and the installed files.

Step 3 If Cisco IDS Host Sensor or another intrusion-detection application is installed on the Cisco Personal Assistant server, uninstall the application before installing Cisco Security Agent for Cisco Personal Assistant. Refer to the Cisco IDS Host Sensor or other applicable documentation.

Step 4 If Windows Automatic Update is configured to automatically download updates from the Microsoft website, disable it.

Step 5 If virus-scanning software is installed on the Personal Assistant server, disable and stop the scanning services:

a. On the Windows Start menu, click Programs > Administrative Tools > Services.

b. In the right pane, double-click the name of the first virus-scanning service.

c. On the General tab, in the Startup Type list, click Disabled. This prevents the service from starting when you restart the server.

d. Click Stop to stop the service immediately.

e. Click OK to close the Properties dialog box.

f. Repeat Step b through Step e for each of the remaining virus-scanning services.

g. When the services have been disabled, close the Services MMC.

Step 6 In Windows Explorer, browse to the directory to which you downloaded the Cisco Security Agent for Cisco Personal Assistant file, and double-click CiscoPA-CSA-4.0.3.720-1.1.3-K9.exe.

Step 7 Follow the on-screen prompts.


Caution Do not change any of the default values, or the Cisco Security Agent may not function properly.

Step 8 When the installation completes, click Yes, I Want to Restart My Computer Now, and click Finish.

Cisco Security Agent for Cisco Personal Assistant begins to work as soon as you restart the Personal Assistant server. You do not need to configure the application.

Step 9 If virus-scanning software is installed on the Personal Assistant server, re-enable and start the scanning services:

a. On the Windows Start menu, click Programs > Administrative Tools > Services.

b. In the right pane, double-click the name of the first virus-scanning service.

c. On the General tab, in the Startup Type list, click Automatic to re-enable the service.

d. Click Start to start the service.

e. Click OK to close the Properties dialog box.

f. Repeat Step b through Step e for each of the remaining virus-scanning services.

g. When the services have been disabled, close the Services MMC.


Upgrading to Cisco Security Agent for Cisco Personal Assistant 1.1(3)

Use the task list in this section to upgrade to version 1.1(3) of the Cisco Security Agent for Cisco Personal Assistant. The tasks refer to sections in these release notes.

Upgrade Task List

1. Download the software. See the "Downloading Cisco Security Agent for Cisco Personal Assistant 1.1(3)" section.

2. Disable the Cisco Security Agent service. See the procedure "To Disable and Stop the Cisco Security Agent Service" in the "Disabling and Re-enabling the Cisco Security Agent Service" section.

3. Uninstall the previous version. See the "Uninstalling Cisco Security Agent for Cisco Personal Assistant" section.

4. Install version 1.1(3). See the "Installing Cisco Security Agent for Cisco Personal Assistant 1.1(3)" section. When the installation is complete, the Cisco Security Agent service is enabled automatically.

Disabling and Re-enabling the Cisco Security Agent Service

The Cisco Security Agent service must be disabled and stopped before you install or upgrade any software on the Personal Assistant server. (For information on other situations in which you must disable the Cisco Security Agent service, see the "Cisco Security Agent Service Must Be Disabled for Specific Tasks" section.)


Caution When you disable and stop the Cisco Security Agent service, you must re-enable and start it before it can monitor the Personal Assistant server again.


Caution Do not stop the Cisco Security Agent service by using the net stop command or the Cisco Security Agent icon in the taskbar. These methods are not supported.

To Disable and Stop the Cisco Security Agent Service


Step 1 On the Windows Start menu, click Programs > Administrative Tools > Services.

Step 2 In the right pane, double-click Cisco Security Agent.

Step 3 On the General tab, in the Startup Type list, click Disabled. This prevents the service from starting when you restart the server.

Step 4 Click Stop to stop the service immediately.

Step 5 Click OK to close the Cisco Security Agent Properties dialog box.

Step 6 When the service has been disabled, close the Services MMC.


To Re-enable and Start the Cisco Security Agent Service


Step 1 On the Windows Start menu, click Programs > Administrative Tools > Services.

Step 2 In the right pane, double-click Cisco Security Agent.

Step 3 On the General tab, in the Startup Type list, click Automatic to re-enable the service.

Step 4 Click Start to start the service.

Step 5 Click OK to close the Cisco Security Agent Properties dialog box.

Step 6 When the service has been re-enabled, close the Services MMC.


Uninstalling Cisco Security Agent for Cisco Personal Assistant

To Uninstall Cisco Security Agent for Cisco Personal Assistant


Step 1 Right-click the Cisco Security Agent icon in the Windows taskbar, and click Suspend Security.

If the icon does not appear in the taskbar, on the Windows Start menu, click Programs > Administrative Tools > Services, and stop the Cisco Security Agent service.

Step 2 On the Windows Start menu, click Programs > Cisco Systems > Uninstall Cisco Security Agent.

Step 3 Click Yes to confirm that you want to uninstall Cisco Security Agent for Cisco Personal Assistant.

Step 4 Click Yes again to restart the Personal Assistant server.


New and Changed Functionality—Release 1.1(3)

This section contains information about new and changed functionality for Cisco Security Agent for Cisco Personal Assistant, Release 1.1(3) only. Refer to the release notes of the applicable version for information about new and changed functionality in earlier versions of Cisco Security Agent for Cisco Personal Assistant. Release notes for all versions of Cisco Security Agent for Cisco Personal Assistant are available at http://www.cisco.com/en/US/products/sw/voicesw/ps2026/prod_release_notes_list.html.

Version 1.1(3) Compiled with Cisco Security Agent Version 4.0.3.720

Cisco Security Agent for Cisco Personal Assistant 1.1(3) is compiled with Cisco Security Agent version 4.0.3, build 720.

Caveats

This section describes Severity 1, 2, and select Severity 3 caveats.

If you have an account with Cisco.com, you can use Bug Toolkit to find more information on the caveats in this section, in addition to caveats of any severity for any release. Bug Toolkit is available at the website http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl.

Note that this section contains caveat information for Cisco Security Agent for Cisco Personal Assistant version 1.1(3), and for Cisco Security Agent versions 4.0.1, build 539 through 4.0.3, build 720 that may affect Cisco Security Agent for Cisco Personal Assistant. For caveat information for earlier versions of Cisco Security Agent for Cisco Personal Assistant, refer to the applicable release notes. Release notes for all versions of Cisco Security Agent for Cisco Personal Assistant are available at http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_release_notes_list.html.

Open Caveats—Release 1.1(3)

There are no open caveats for Cisco Security Agent for Cisco Personal Assistant Release 1.1(3).

Resolved Caveat—Release 1.1(3)

Table 1 Cisco Security Agent for Cisco Personal Assistant Release 1.1(3) Resolved Caveat

Caveat Number
Severity
Component
Description

CSCef26489

3

ciscosecurityagent

CSA Rules Conflict with Exchange Data Paths.


Troubleshooting

The following sections contain information on troubleshooting Cisco Security Agent for Cisco Personal Assistant:

Problems with Cisco Personal Assistant or Errors from Cisco Security Agent

Second Attempt to Install Software Fails Without a Warning

Problems with Cisco Personal Assistant or Errors from Cisco Security Agent

Do the procedure in this section, if you encounter any of the following problems after installing Cisco Security Agent for Cisco Personal Assistant:

Problems with Personal Assistant that cannot otherwise be explained.

Cisco Security Agent errors in the Windows event log or in the Cisco Security Agent log file, <Drive>:\Program Files\Cisco\CSAgent\log\securitylog.txt.

Cisco Security Agent error messages displayed on the screen.

If you cannot determine the cause of a Cisco Security Agent log entry or error message, contact Cisco TAC.

To Troubleshoot Problems with Personal Assistant or Errors from Cisco Security Agent


Step 1 In the Windows taskbar, right-click the Cisco Security Agent icon, and click Suspend Security.

Step 2 Perform the operation that caused the error message.

Step 3 In the Windows taskbar, right-click the Cisco Security Agent icon, and click Resume Security.

Step 4 Perform the operation that caused the error message.

Step 5 If the operation completes successfully with the Cisco Security Agent suspended and continues to fail with the Cisco Security Agent enabled, confirm that all of the software running on the Personal Assistant server is listed as supported in the "Requirements and Supported Software" section.

If unsupported software is installed on the server, remove the unsupported software and repeat this procedure.

Step 6 If you are unable to resolve the problem, contact Cisco TAC and send them the Cisco Security Agent log file, <Drive>:\Program Files\Cisco\CSAgent\log\securitylog.txt.


Second Attempt to Install Software Fails Without a Warning

In the following case, an attempt to install software will fail without a warning:

1. You tried to install software without first disabling and stopping the Cisco Security Agent service.

2. Cisco Security Agent displayed the message

"Cisco Security Agent: A problem was detected, press one of the action buttons below.
Are you installing/uninstalling software? If not, this operation is suspicious."

3. You clicked No.

4. You disabled and stopped the Cisco Security Agent service.

5. You tried again to install the software installation, but nothing happened.

When you clicked No in Step 3., your answer was cached in memory. The cache is cleared automatically after an hour. To clear the cache immediately so you can install the software now, do the following procedure.

To Clear the Cisco Security Agent Memory Cache So You Can Install Software


Step 1 In the Windows taskbar, double-click the Cisco Security Agent icon.

Step 2 Click the Advanced tab.

Step 3 Click Clear.

Step 4 Close the Cisco Security Agent Control Panel.

Step 5 Before you retry installing software on the server, disable the Cisco Security Agent service. See the procedure "To Disable and Stop the Cisco Security Agent Service" section.

Step 6 After you install the software, re-enable the Cisco Security Agent service. See the procedure "To Re-enable and Start the Cisco Security Agent Service" section.


Cisco Personal Assistant Documentation

For descriptions and URLs of Personal Assistant documentation on Cisco.com, refer to About Cisco Personal Assistant Documentation. The document is shipped with Personal Assistant and is available at http://www.cisco.com/univercd/cc/td/doc/product/voice/assist/about/padoc.htm.

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:

http://www.cisco.com/en/US/partner/ordering/index.shtml

Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).

Documentation Feedback

You can send comments about technical documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.

Cisco Technical Support Website

The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool automatically provides recommended solutions. If your issue is not resolved using the recommended resources, your service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553 2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)—Your network is "down," or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:

http://cisco.com/univercd/cc/td/doc/pcat/

Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

http://www.ciscopress.com

Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:

http://www.cisco.com/packet

iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

World-class networking training is available from Cisco. You can view current offerings at this URL:

http://www.cisco.com/en/US/learning/index.html