Command Line Interface
Overview
This appendix describes commands that you can use on the Cisco IPT Platform to perform basic platform functions. The Cisco IPT Platform Administration GUI application also makes these functions available. Typically you would use the command-line interface (CLI) only when a problem occurs while you are using the Cisco IPT Platform Administration interface.
Starting a CLI Session
You can access the Cisco IPT Platform CLI remotely or locally:
•
From a web client workstation, such as the workstation that you use for Cisco IPT Platform Administration, you can use SSH to connect securely to the Cisco IPT Platform.
•You can access the Cisco IPT Platform CLI directly by using the monitor and keyboard that you used during installation or by using a terminal server that is connected to the serial port. Use this method if a problem exists with the IP address.
Before You Begin
Ensure you have the following information that gets defined during installation:
•A primary IP address and hostname
•An administrator ID
•A password
You will need this information to log in to the Cisco IPT Platform.
Perform the following steps to start a CLI session:
Step 1 Do one of the following actions depending on your method of access:
•From a remote system, use SSH to connect securely to the Cisco IPT Platform. In your SSH client, enter
ssh adminname@hostname
where adminname specifies the Administrator ID and hostname specifies the hostname that was defined during installation.
For example, ssh admin@ipt-1.
•From a direct connection, you receive this prompt automatically:
where ipt-1 represents the host name of the system.
Enter the administrator ID that was defined during installation.
In either case, the system prompts you for a password.
Step 2 Enter the password that was defined at installation.
The CLI prompt displays. The prompt represents the Administrator ID; for example:
admin:
You can now use any CLI command.
CLI Basics
The following section contains basic tips for using the command line interface.
Completing Commands
To complete commands, use Tab:
•Enter the start of a command and press Tab to complete the command. For example, if you enter se and press Tab, set gets completed.
•Enter a full command name and press Tab to display all the commands or subcommands that are available. For example, if you enter set and press Tab, you see all the set subcommands. An * identifies the commands that have subcommands.
•If you reach a command, keep pressing Tab, and the current command line repeats; this indicates that no additional expansion is available.
Getting Help on Commands
You can get two kinds of help on any command:
•Detailed help that includes a definition of the command and an example of its use
•Short query help that includes only command syntax
Procedure
To get detailed help, at the CLI prompt, enter
help command
Where command specifies the command name or the command and parameter. See Example 1.
To query only command syntax, at the CLI prompt, enter
command?
Where command represents the command name or the command and parameter. See Example 2.
Note If you enter a ? after a menu command, such as set, it acts like the Tab key and lists the commands that are available.
Example 1 Detailed Help Example:
admin:help file list activelog
This will list active logging files
detail - show detailed listing
reverse - reverse sort order
file-spec can contain '*' as wildcards
admin:file list activelog platform detail
02 Dec,2004 12:00:59 <dir> drf
02 Dec,2004 12:00:59 <dir> log
16 Nov,2004 21:45:43 8,557 enGui.log
27 Oct,2004 11:54:33 47,916 startup.log
dir count = 2, file count = 2
Example 2 Query Example:
admin:file list activelog?
file list activelog file-spec [options]
file-spec mandatory file to view
options optional page|detail|reverse|[date|size]
Ending a CLI Session
At the CLI prompt, enter quit. If you are logged in remotely, you get logged off, and the ssh session gets dropped. If you are logged in locally, you get logged off, and the login prompt returns.
Cisco IPT Platform CLI Commands
The following tables list and describe the CLI commands that are available for the Cisco IP Telephony Platform and for Cisco Unified MobilityManager.
File Commands
The following table lists and explains the CLI File commands:
Table A-1 File Commands
|
|
|
|
file delete |
activelog directory/filename [detail] [noconfirm] inactivelog directory/filename [detail] [noconfirm] install directory/filename [detail] [noconfirm] Where •activelog specifies a log on the active side. •inactivelog specifies a log on the inactive side. •install specifies an installation log. You can use the wildcard character, *, for filename.
Caution
You cannot recover a deleted file except, possibly, by using the Disaster Recovery System
Options •detail—Displays a listing of deleted files with the date and time. •noconfirm—Deletes files without asking you to confirm each deletion. |
This command deletes one or more files. Command privilege level: 1 Allowed during upgrade: Yes Example: Delete the install log
file delete install install.log
|
file dump |
activelog directory/filename [page] [detail] [hex] inactivelog directory/filename [page] [detail] [hex] install directory/filename [page] [detail] [hex] Where •activelog specifies a log on the active side. •inactivelog specifies a log on the inactive side. •install specifies an installation log. You can use the wildcard character, *, for filename as long as it resolves to one file. Options •page—Displays output one page at a time. •detail—Displays listing with the date and time. •hex—Displays output in hexadecimal. |
This command dumps the contents of a file to the screen. Command privilege level: 1 Allowed during upgrade: Yes Example: Dump contents of file _cdrIndex.idx
file dump activelog
cm/cdr/_cdrIndex.idx
|
file get |
activelog directory/filename [reltime] [abstime] [match] [recurs] inactivelog directory/filename [reltime] [abstime] [match] [recurs] install directory/filename [reltime] [abstime] [match] [recurs] Where •activelog specifies a log on the active side. •inactivelog specifies a log on the inactive side. •install specifies an installation log. Options •abstime—Absolute time period, specified as hh:mm:MM/DD/YY hh:mm:MM/DD/YY
•reltime—Relative time period, specified as minutes | hours | days | weeks | months <value>
•match—Match a particular string in the filename, specified as
•recurs—Get all files, including subdirectories After the command identifies the specified files, you get prompted to enter an SFTP host, username, and password. |
This command sends the file to another system by using SFTP. Command privilege level: 0 Allowed during upgrade: Yes Example 1: Get all files in the activelog platform directory that match the string "plat"
file get activelog platform match plat
Example 2: Get all platform log files for a particular time period
file get activelog platform/log abstime
18:00:9/27/200 18:00:9/28/2005
|
file list |
activelog directory [page] [detail] [reverse] [date | size] inactivelog directory [page] [detail] [reverse] [date | size] install directory [page] [detail] [reverse] [date | size] Where •activelog specifies a log on the active side. •inactivelog specifies a log on the inactive side. •install specifies an installation log. Note You can use a wildcard character, *, for directory name as long as it resolves to one directory. Options •detail—Long listing with date and time •date—Sort by date •size—Sort by file size •reverse—Reverse sort direction •page—Displays the output one screen at a time |
This command lists the log files in an available log directory. Command privilege level: 1 Allowed during upgrade: Yes Example 1: List Platform Log files with details
file list activelog platform/log page
detail
Example 2: List directories in CDR Repository
file list activelog cm/cdr_repository
Example 3: List CDR files in a specified directory by size
file list activelog
cm/cdr_repository/processed/20050812
size
|
file search |
activelog directory/filename reg-exp [page] [detail] [ignorecase] inactivelog directory/filename reg-exp [page] [detail] [ignorecase] install directory/filename reg-exp [page] [detail] [ignorecase] Where •activelog specifies a log on the active side. •inactivelog specifies a log on the inactive side. •install specifies an installation log. •reg-exp represents a regular expression. Note You can use the wildcard character, *, to represent all or part of the filename. Options •page—Displays the output one screen at a time •detail—Displays a detailed listing •ignorecase—Ignores case when searching |
This command searches the content of a log and displays the matching lines. Write the search term in the form of a regular expression, which is a special text string for describing a search pattern. Command privilege level: 0 Allowed during upgrade: Yes Example
file search activelog
platform/log/platform.log Err[a-z] page
ignorecase
|
file tail |
activelog directory/filename [detail] [hex] [lines] inactivelog directory/filename [detail] [hex] [lines] install directory/filename [detail] [hex] [lines] Where •activelog specifies a log on the active side. •inactivelog specifies a log on the inactive side. •install specifies an installation log. You can use the wildcard character, *, for filename so long as it resolves to one file. Options •detail—Long listing with date and time •hex—Hexadecimal listing •lines—Number of lines to display |
This command tails (prints the last few lines) of a log file. Command privilege level: 1 for logs Allowed during upgrade: Yes Example: Tail the platform CLI log file
file tail activelog
platform/log/cli00001.log
|
file view |
activelog directory/filename inactivelog directory/filename install directory/filename Where •activelog specifies a log on the active side. •inactivelog specifies a log on the inactive side. •install specifies an installation log. Note You can use the wildcard character, *, for filename so long as it resolves to one file. |
This command displays the contents of a file. Command privilege level: 0 Allowed during upgrade: Yes Example 1: Display the install log
file view install install.log
Example 2: Display a particular CDR file
file view activelog
/cm/cdr_repository/processed/20058012/{
filename}
|
Show Commands
The following table lists and explains the CLI Show commands:
Table A-2 Show Commands
|
|
|
|
show account |
None |
This command lists current administrator accounts, except the master administrator account. Command privilege level: 4 Allowed during upgrade: Yes |
show cert |
own filename trust filename list {own | trust} Where •filename represents the name of the certificate file. •own specifies owned certificates. •trust specifies trusted certificates. •list specifies a certificate trust list. Options None |
This command displays certificate contents and certificate trust lists. Command privilege level: 1 Allowed during upgrade: Yes Example: Display own certificate trust lists
|
show firewall |
list [detail] [page] [file filename] Where •detail—Displays detailed statistics on every available device on the system •page—Displays the output one page at a time •file filename—Outputs the information to a file Note The file option saves the information to platform/cli/filename.txt. The file name cannot contain the "." character. |
This command displays system aspects of the server. Command privilege level: 1 Allowed during upgrade: Yes |
show hardware |
None |
This command displays the following information on the platform hardware: •Platform •Serial number •BIOS build level •BIOS manufacturer •Active processors Command privilege level: 0 Allowed during upgrade: Yes |
show myself |
None |
This command displays information about the current account. Command privilege level: 0 Allowed during upgrade: Yes |
show network |
eth0 [detail] route [detail] status [detail] [listen] [process] [all] [nodns] [search stext] all [detail] Where •eth0 specifies Ethernet 0. •route specifies network routing information. •status specifies active Internet connections. •all specifies all basic network information. Options •detail—Displays additional information •listen—Displays only listening sockets •process—Displays the process ID and name of the program to which each socket belongs •all—Displays both listening and nonlistening sockets •nodns—Displays numerical addresses without any DNS information •search stext—Searches for the stext in the output |
This command displays network information. Command privilege level: 0 Allowed during upgrade: Yes Example: Display active Internet connections
|
show packages |
active name [page] inactive name [page] Where name represents the package name. To display all active or inactive packages, use the wildcard character, *. Options page—Displays the output one page at a time |
This command displays the name and version for installed packages. Command privilege level: 0 Allowed during upgrade: Yes |
show process |
load [cont] [clear] [noidle] [num xx] [thread] [cpu] [memory] [time] [specified] [page] list [page] [short] [detail] [thread] [fd] [cont] [clear] [process id id] [argument id id] [owner name name] Where •load displays the CPU load for each active process. •list displays all processes. Options •cont—Command repeats continuously •clear—Clears screen before displaying output •noidle—Ignore idle or zombie processes •num xx—Sets the number of processes to display (Default=10, all = all processes) •thread—Displays threads •cpu—Displays output by CPU usage •memory—Sorts output by memory usage •short—Displays short listing •time—Sorts output by time usage •page—Displays one page at a time •detail—Displays a detailed listing •process id id—Shows only specific process number or command name •argument name name—Show only specific process with argument name •thread—Include thread processes in the listing •fd—Show file descriptors that are associated with a process |
This command displays process and load information. Command privilege level: 1 Allowed during upgrade: Yes Example: Show detailed process listing one page at a time
show process list detail page
|
show stats |
io [kilo] [detail] [page] [file filename] Options •kilo—Displays statistics in kilobytes •detail—Displays detailed statistics on every available device on the system and overrides the kilo option •file filename—Outputs the information to a file Note The file option saves the information to platform/cli/filename.txt. The file name cannot contain the "." character. |
This command displays system IO statistics. Command privilege level: 1 Allowed during upgrade: Yes |
show status |
None |
This command displays the following basic platform status: •Host name •Date •Time zone •Locale •Product version •Platform version •CPU usage •Memory and disk usage Command privilege level: 0 |
show tech |
all [page] [file filename] Options •page—Displays one page at a time •file filename—Outputs the information to a file Note The file option saves the information to platform/cli/filename.txt. The file name cannot contain the "." character. |
This command displays the combined output of all show tech commands. Command privilege level: 1 Allowed during upgrade: Yes |
show tech |
network [page] [file filename] Options •page—Displays one page at a time •file filename—Outputs the information to a file Note The file option saves the information to platform/cli/filename.txt. The file name cannot contain the "." character. |
This command displays network aspects of the server. Command privilege level: 1 Allowed during upgrade: Yes |
show tech |
runtime [page] [file filename] Options page—Displays one page at a time file filename—Outputs the information to a file Note The file option saves the information to platform/cli/filename.txt. The file name cannot contain the "." character. |
This command displays runtime aspects of the server. Command privilege level: 1 Allowed during upgrade: Yes |
show tech |
system [page] [file filename] Options page—Displays one page at a time file filename—Outputs the information to a file Note The file option saves the information to platform/cli/filename.txt. The file name cannot contain the "." character. |
This command displays system aspects of the server. Command privilege level: 1 Allowed during upgrade: Yes |
show timezone |
config list [page] Where •config displays the current time zone settings. •list displays the available time zones. Options page—Displays the output one page at a time |
This command displays time zone information. Command privilege level: 0 Allowed during upgrade: Yes |
show trace |
[task_name] Where task_name represents the name of the task for which you want to display the trace information. Note If you do not enter any parameters, the command returns a list of available tasks. Options None |
This command displays trace information for a particular task. Command privilege level: 0 Allowed during upgrade: Yes Example: Display trace information for cdp
|
show version |
active inactive Options None |
This command displays the software version on the active or inactive partition. Command privilege level: 0 Allowed during upgrade: Yes |
show workingdir |
None |
This command retrieves the current working directory for activelog, inactivelog, and install. Command privilege level: 0 Allowed during upgrade: Yes |
Set Commands
The following table lists and explains the CLI Set commands.
Table A-3 Set Commands
|
|
|
|
set account |
name Where name represents the username for the new account. Note After you enter the username, the system prompts you to enter the privilege level and password for the new account. Options None |
This command sets up a new account on the platform. Command privilege level: 0 Allowed during upgrade: No |
set cert |
regen unit-name Where unit-name represents the name of the certificate that you want to regenerate. Options None |
This command enables you to regenerate the specified security certificate. Command privilege level: 1 Allowed during upgrade: No |
set logging |
{enable | disable} Options None |
This command allows you to enable or disable logging. Command privilege level: 0 Allowed during upgrade: Yes |
set network |
dhcp eth0 {enable | disable} Where •eth0 specifies Ethernet interface 0. The system asks whether you want to continue to execute this command.
Warning
If you continue, this command causes the system to restart. Cisco also recommends that you restart all nodes whenever any IP address gets changed.
Options None |
This command enables or disables DHCP for Ethernet interface 1 or 0. Command privilege level: 1 Allowed during upgrade: No |
set network |
dns {primary | secondary} ip-address Where ip-address represents the IP address of the primary or secondary DNS server. The system asks whether you want to continue to execute this command.
Warning
If you continue, this command causes a temporary loss of network connectivity.
Options None |
This command sets the IP address for the primary or secondary DNS server. Command privilege level: 1 Allowed during upgrade: No |
set network |
domain domain-name Where domain-name represents the system domain that you want to assign. The system asks whether you want to continue to execute this command.
Warning
If you continue, this command causes a temporary loss of network connectivity.
Options None |
This command sets the domain name for the system. Command privilege level: 1 Allowed during upgrade: No |
set network |
gateway ip-address Where ip-address represents the IP address of the network gateway that you want to assign. The system asks whether you want to continue to execute this command.
Warning
If you continue, this command causes the system to restart.
Options None |
This command enables you to configure the IP address of the network gateway. Command privilege level: 1 Allowed during upgrade: No |
set network |
ip eth0 ip-address ip-mask Where •eth0 specifies Ethernet interface 0. •ip-address represents the IP address that you want assign. •ip-mask represents the IP mask that you want to assign. The system asks whether you want to continue to execute this command.
Warning
If you continue, this command causes the system to restart.
Options None |
This command sets the IP address for Ethernet interface 1 or 0. Command privilege level: 1 Allowed during upgrade: No |
set network |
nic eth0 [auto en | dis] [speed 10 | 100] [duplex half | full] Where •eth0 specifies Ethernet interface 0. •auto specifies whether auto negotiation gets enabled or disabled. •speed specifies whether the speed of the Ethernet connection: 10 or 100 Mbps. •duplex specifies half-duplex or full-duplex. The system asks whether you want to continue to execute this command. Note You can enable only one active NIC at a time.
Warning
If you continue, this command causes a temporary loss of network connections while the NIC gets reset.
Options None |
This command sets the properties of the Network Interface Card (NIC). Command privilege level: 1 Allowed during upgrade: No |
set network |
status eth0 {up | down} Where eth0 specifies Ethernet interface 0. Options None |
This command sets the status of Ethernet 1 or Ethernet 0 to up or down. Command privilege level: 1 Allowed during upgrade: No |
set output |
{enable | disable} Options None |
This command allows you to enable or disable the platform output. Command privilege level: 0 Allowed during upgrade: Yes |
set password |
{admin | security} The systems prompts you for the old and new passwords. Note The password must contain at least six characters, and the system checks it for strength. |
This command allows you to change the administrator and security passwords. Command privilege level: 1 Allowed during upgrade: No |
set timezone |
timezone Note Enter enough characters to uniquely identify the new time zone. Be aware that the time-zone name is case-sensitive.
Caution
You must restart the system after you change the time zone.
Options None |
This command lets you change the system time zone. Command privilege level: 0 Allowed during upgrade: No Example: Set the time zone to Pacific time
|
set web-security |
orgunit orgname locality state country Where •orgunit represents the organizational unit. •orgname represents the organizational name. •locality represents the organization's location. •state represents the organization's state. •country represents the organization's country. Options None |
This command sets the web security certificate information for the platform. Command privilege level: 0 Allowed during upgrade: No |
set workingdir |
activelog directory inactivelog directory install directory Where •activelog sets the working directory for active logs. •inactivelog set the working directory for inactive logs. •install sets the working directory for installation logs. •directory represents the current working directory. Options None |
This command sets the working directory for active, inactive, and installation logs. Command privilege level: 0 Allowed during upgrade: Yes |
Delete Commands
The following table lists and explains the CLI Delete commands:
Table A-4 Delete Commands
|
|
|
|
delete account |
account-name Where account-name represents the name of an administrator account. Options None |
This command allows you to delete an administrator account. Command privilege level: 4 Allowed during upgrade: No |
delete dns |
ip-address Where ip-address represents the IP address of the DNS server you want to delete. The system asks whether you want to continue to execute this command.
Warning
If you continue, this command causes a temporary loss of network connectivity.
Options None |
This command allows you to delete the IP address for a DNS server. Command privilege level: 1 Allowed during upgrade: No |
delete process |
process-id [force | terminate | crash] Where •process-id represents the process ID number. Options •force—Tells the process to stop •terminate—Tells the operating system to terminate the process •crash—Crashes the process and produces a crash dump Note Use the force option only if the command alone does not delete the process and use the terminate option only if force does not delete the process. |
This command allows you to delete a particular process. Command privilege level: 1 Allowed during upgrade: Yes |
Utility Commands
The following table lists and explains the CLI Utility commands:
Table A-5 Utility Commands
|
|
|
|
utils csa |
start The system prompts you to confirm that you want to start CSA.
Caution
You must restart the system after you start CSA.
Options None |
This command starts Cisco Security Agent (CSA). Command privilege level: 1 Allowed during upgrade: No |
utils csa |
status The system indicates whether CSA is running or not. Options None |
This command displays the current status of Cisco Security Agent (CSA). Command privilege level: 0 Allowed during upgrade: No |
utils csa |
stop The system stops CSA. Options None |
This command stops Cisco Security Agent (CSA). Command privilege level: 1 Allowed during upgrade: No |
utils disaster_
recovery |
backup tape tapeid Where tapeid represents the ID of an available tape device. Options None |
This command starts a backup job and stores the resulting tar file on tape. Command privilege level: 1 Allowed during upgrade: No |
utils disaster_
recovery |
backup network path servername username Where •path represents the location of the backup files on the remote server. •servername represents the IP address or host name of the server where you stored the backup files. •username represents the username that is needed to log in to the remote server. Note The system prompts you to enter the password for the account on the remote server. Options None |
This command starts a backup job and stores the resulting tar file on a remote server. Command privilege level: 1 Allowed during upgrade: No |
utils disaster_
recovery |
cancel_bakckup The system prompts you to confirm that you want to cancel the backup job. Options None |
This command cancels the ongoing backup job. Command privilege level: 1 Allowed during upgrade: No |
utils disaster_
recovery |
restore tape server tarfilename tapeid Where •server specifies the hostname of the server that you want to restore. •tarfilename specifies the name of the file to restore. •tapeid specifies the name of the tape device from which to perform the restore job. Options None |
This command starts a restore job and takes the backup tar file from tape. Command privilege level: 1 Allowed during upgrade: No |
utils disaster_
recovery |
restore network restore_server tarfilename path servername username Where •restore_server specifies the hostname of the server that you want to restore. •tarfilename specifies the name of the file to restore. •path represents the location of the backup files on the remote server. •servername represents the IP address or host name of the server where you stored the backup files. •username represents the username that is needed to log in to the remote server. Note The system prompts you to enter the password for the account on the remote server. Options None |
This command starts a restore job and takes the backup tar file from a remote server. Command privilege level: 1 Allowed during upgrade: No |
utils disaster_
recovery |
show_backupfiles network path servername username Where •path represents the location of the backup files on the remote server. •servername represents the IP address or host name of the server where you stored the backup files. •username represents the username that is needed to log in to the remote server. Note The system prompts you to enter the password for the account on the remote server. Options None |
This command displays information about the backup files that are stored on a remote server. Command privilege level: 1 Allowed during upgrade: Yes |
utils disaster_
recovery |
show_bakcupfiles tape tapeid Where tapeid represents the ID of an available tape device. Options None |
This command displays information about the backup files that are stored on a tape. Command privilege level: 1 Allowed during upgrade: Yes |
utils disaster_
recovery |
show_registration hostname Where hostname specifies the server for which you want to display registration information. Options None |
This command displays the registered features and components on the specified server. Command privilege level: 1 Allowed during upgrade: Yes |
utils disaster_
recovery |
show_tapeid Options None |
This command displays a list of tape device IDs. Command privilege level: 1 Allowed during upgrade: Yes |
utils disaster_
recovery |
status operation Where operation specifies the name of the ongoing operation: backup or restore. Options None |
This command displays the status of the current backup or restore job. Command privilege level: 1 Allowed during upgrade: Yes |
utils dsm |
start The system confirms that the process started.
Caution
You must restart the system after you start this process.
Options None |
This command starts the database storage manager. Command privilege level: 1 Allowed during upgrade: No |
utils dsm |
status The system indicates whether the database process is running or not. Options None |
This command displays the current status of the database storage manager. Command privilege level: 0 Allowed during upgrade: No |
utils network |
arp list [host host][page][numeric] arp set {host} {address} arp delete host Where •arp list lists the contents of the address resolution protocol table. •arp set sets an entry in the address resolution protocol table. •arp delete deletes an entry in the address resolution table. •host represents the host name or IP address of the host to add or delete to the table. •address represents the MAC address of the host to be added. Enter the MAC address in the following format: XX:XX:XX:XX:XX:XX. Options page—Displays the output one page at a time numeric—Displays hosts as dotted IP addresses |
This command lists, sets, or deletes Address Resolution Protocol (ARP) table entries. Command privilege level: 0 Allowed during upgrade: Yes |
utils network |
capture eth0 [page] [numeric] [file fname] [count num] [size bytes] [src addr] [dest addr] [port num] Where eth0 specifies Ethernet interface 0. Options •page—Displays the output one page at a time Note When you use the page or file options, the complete capture of all requested packets must occur before the command completes. •numeric—Displays hosts as dotted IP addresses •file fname—Outputs the information to a file Note The file option saves the information to platform/cli/fname.cap. The filename cannot contain the "." character. count num—Sets a count of the number of packets to capture Note For screen output, the maximum count equals 1000, and, for file output, the maximum count equals 10,000. •size bytes—Sets the number of bytes of the packet to capture Note For screen output, the maximum number of bytes equals 128, for file output, the maximum of bytes can be any number or ALL •src addr—Specifies the source address of the packet as a host name or IPV4 address •dest addr—Specifies the destination address of the packet as a host name or IPV4 address •port num—Specifies the port number of the packet, either source or destination |
This command captures IP packets on the specified Ethernet interface. You can display the packets on the screen or save them to a file. Line wrapping can occur in the output. Command privilege level: 0 Allowed during upgrade: Yes |
utils network |
host hostname [server server-name][page][detail] Where hostname represents the host name or IP address that you want to resolve. Options server-name—Specifies an alternate domain name server page—Displays the output one screen at a time detail—Displays a detailed listing |
This command resolves a host name to an address or an address to a host name. Command privilege level: 0 Allowed during upgrade: Yes |
utils network |
ping destination [count] Where destination represents the hostname or IP address of the server that you want to ping. Options count—Specifies the number of times to ping the external server. The default count equals 4. |
This command allows you to ping another server. Command privilege level: 0 Allowed during upgrade: Yes |
utils network |
tracert destination [eth0] Where destination represents the hostname or IP address of the server to which you want to send a trace. Options eth0—Sets the source Ethernet address |
This command traces IP packets that are sent to a remote destination. Command privilege level: 0 Allowed during upgrade: Yes |
utils ntp |
{status | config} |
This command displays the NTP status or configuration. Command privilege level: 0 Allowed during upgrade: Yes |
utils remote_
account |
status enable disable create username life Where username specifies the name of the remote account. The username can contain only lowercase characters and must be more than six-characters long. life specifies the life of the account in days. After the specified number of day, the account expires. Note You can have only one remote account that is enabled at a time. Options None |
This command allows you to enable, disable, create, and check the status of a remote account. Note A remote account generates a pass phrase that allows Cisco Systems support personnel to get access to the system for the specified life of the account. Command privilege level: 1 Allowed during upgrade: Yes Example
utils remote_account status
|
utils system |
{restart | shutdown | switch-version} Note The system prompts you to confirm the action that you choose. |
This command allows you to restart the system on the same partition, restart the system on the inactive partition, or shut down the system. Command privilege level: 1 Allowed during upgrade: No |
Feedback