Guest

Cisco Unified IP Phone 7900 Series

Cisco Unified IP Phone 7975G, 7965G, 7962G, 7945G and 7942G Release Notes for Firmware Release 8.4(2) (SCCP and SIP)

  • Viewing Options

  • PDF (248.9 KB)
  • Feedback
Cisco Unified IP Phone 7975G, 7965G, 7962G, 7945G and 7942G Release Notes for Firmware Release 8.4(2) (SCCP and SIP)

Table Of Contents

Cisco Unified IP Phone 7975G, 7965G, 7962G, 7945G and 7942G Release Notes for Firmware Release 8.4(2) (SCCP and SIP)

Contents

Related Documentation

New and Changed Information

Hold Status

Missed Calls

Restrict Unconfigured Phone Registration

Installation Notes

Installing Firmware Release 8.4(2) for SCCP

Firmware Installation Procedure for SCCP

Installing Firmware Release 8.4(2) for SIP

Firmware Installation Procedure for SIP

Installing Firmware Release for the Cisco Unified IP Phone Expansion Module

Cisco Unified IP Phone Expansion Module 7916 and Cisco Unified IP Phone Expansion Module 7915

Cisco Unified IP Phone Expansion Module 7914

Important Notes

Initial Startup Time for the Cisco Unified IP Phones

Geometric TCP

Caveats

Using Bug Toolkit

Open Caveats

Open SCCP Caveats

Open SCCP and SIP Caveats

Open SIP Caveats

Resolved Caveats

Resolved SCCP Caveats

Resolved SCCP and SIP Caveats

Resolved SIP Caveats

Obtaining Documentation and Submitting a Service Request


Cisco Unified IP Phone 7975G, 7965G, 7962G, 7945G and 7942G Release Notes for Firmware Release 8.4(2) (SCCP and SIP)


Revised: October 15, 2009

Use these release notes with a Cisco Unified IP Phone 7975G, 7965G, 7962G, 7945G or 7942G running SCCP or SIP firmware release 8.4(2).

The SCCP version of firmware release 8.4(2) is compatible with Cisco Unified Communications Manager releases 7.0, 6.1, 6.0, and Cisco Unified CallManager releases 5.1, 4.3, 4.2, and 4.1.

The SIP version of firmware release 8.4(2) is compatible with Cisco Unified Communications Manager releases 7.0, 6.1, 6.0, and Cisco Unified CallManager release 5.1.


Note SIP firmware release 8.4(2) is designed and tested to interoperate with Cisco call control, most notably Cisco Unified Communications Manager release 7.0. Although SIP firmware is IETF RFC 3261 compliant, it is not supported by Cisco TAC or Engineering for use with non-Cisco call control systems.


Contents

These release notes provide the following information. You might need to notify your users about some of the information provided in this document.

Related Documentation

New and Changed Information

Installation Notes

Important Notes

Caveats

Obtaining Documentation and Submitting a Service Request

Related Documentation

Cisco Unified IP Phone Documentation

Refer to publications that are specific to your language, phone model and Cisco Unified Communications Manager release. Navigate from the following documentation URL:

http://www.cisco.com/en/US/products/hw/phones/ps379/tsd_products_support_series_home.html

Cisco Unified Communications Manager Documentation

Refer to the Cisco Unified Communications Manager Documentation Guide and other publications specific to your Cisco Unified Communications Manager release. Navigate from the following URL:

http://www.cisco.com/en/US/products/sw/voicesw/ps556/tsd_products_support_series_home.html

Cisco Unified Communications Manager Business Edition Documentation

Refer to the Cisco Unified Communications Manager Business Edition Documentation Guide and other publications that are specific to your Cisco Unified Communications Manager release. Navigate from the following URL:

http://www.cisco.com/en/US/products/ps7273/tsd_products_support_series_home.html

New and Changed Information

The following sections contain information on features introduced in firmware release 8.4(2).

Hold Status

Missed Calls

Restrict Unconfigured Phone Registration

Hold Status

Cisco Unified Communications Manager 6.1(3) and firmware release 8.4(2) introduce the following enhancements to hold status:

The Hold Status feature allows phones with a shared line to distinguish whether the local user placed the call on hold, or a remote (shared line) user placed the call on hold.

If two phone users share a line and one user places a call on hold, that user's phone displays the local hold icon while the other user's phone displays the remote hold icon. In addition, on the Cisco Unified IP Phone 7906G and 7911G, the hold button is solid red on the local and remote phone. On all other supported phones, the local phone LED flashes green and the remote phone user's LED flashes green.


Note The minimum Unified CM version for this feature is 6.1(3).


The hold status enhancement is supported on the following SCCP and SIP phones:

Cisco Unified IP Phone 7906G

Cisco Unified IP Phone 7911G

Cisco Unified IP Phone 7931G

Cisco Unified IP Phone 7941G

Cisco Unified IP Phone 7941G-GE

Cisco Unified IP Phone 7942G

Cisco Unified IP Phone 7945G

Cisco Unified IP Phone 7961G

Cisco Unified IP Phone 7961G-GE

Cisco Unified IP Phone 7962G

Cisco Unified IP Phone 7965G

Cisco Unified IP Phone 7970G

Cisco Unified IP Phone 7971G-GE

Cisco Unified IP Phone 7975G

Cisco Unified Expansion Module 7916

Cisco Unified Expansion Module 7915

Cisco Unified Expansion Module 7914

Where to Find More Information

Cisco Unified IP Phone Guide

Cisco Unified IP Phone Administration Guide

Missed Calls

The missed calls feature allows the phone administrator to specify whether missed calls will be logged in the missed calls directory for a given line appearance. This feature is supported in Cisco Unified Communications Manager 6.1(3) and later. The following information applies to the missed calls feature:

The line can be a directory number or shared line. The default behavior is to log all missed calls on all lines.

Missed call logging operates on a line basis. The line can be a directory number or a shared line.

If the phone administrator configures a line appearance (share or non-shared), so that missed calls are not logged, then calls to that line are never logged in the missed call log directory, even if the calls were eventually forwarded due to no answer.

If more than one line key gets configured on a phone, logging missed calls is dependent on the missed call log setting for each line.

Missed call logging is controlled by an on/off configuration parameter that is sent to the phone in the configuration file.

The Missed Calls Log configuration does not affect any existing or previous call log items.

Calls on lines that are not logged do not affect the New Missed Call status message.

If the phone administrator turns off the missed calls feature on the configured line appearance, the missed calls are not listed in the missed call history on that line appearance.

The following information applies to all calls:

All calls received on a phone appear in the Received Calls log, regardless of the line on which they were received.

All calls made from a phone appear in the Placed Calls log, regardless of whether they were placed from a shared or primary line.

The missed calls feature is supported on the following SCCP and SIP phones:

Cisco Unified IP Phone 7906G

Cisco Unified IP Phone 7911G

Cisco Unified IP Phone 7931G

Cisco Unified IP Phone 7941G-GE

Cisco Unified IP Phone 7941G

Cisco Unified IP Phone 7942G

Cisco Unified IP Phone 7945G

Cisco Unified IP Phone 7961G-GE

Cisco Unified IP Phone 7961G

Cisco Unified IP Phone 7962G

Cisco Unified IP Phone 7965G

Cisco Unified IP Phone 7970G

Cisco Unified IP Phone 7971G-GE

Cisco Unified IP Phone 7975G

Where to Find More Information

Cisco Unified IP Phone Guide

Cisco Unified IP Phone Administration Guide

Restrict Unconfigured Phone Registration

Prior to Cisco Unified Communications Manager 6.1(3) and firmware release 8.4(2), if a Cisco Unified IP Phone had not been added to the Cisco Unified Communications Manager database and did not have auto-registration enabled, the phone would repeatedly attempt to register (unsuccessfully) with Cisco Unified Communications Manager, thus continually notifying Cisco Unified Communications Manager with these repeated registration requests.

With Cisco Unified Communications Manager 6.1(3) and firmware release 8.4(2), if auto-registration is not enabled, and the phone has not been added to the Cisco Unified Communications Manager database, the phone will not attempt to register with Cisco Unified Communications Manager. The phone will continue to display the "Configuring IP" message until auto-registration has been enabled, or until the phone has been added to the Cisco Unified Communications Manager database.


Note The minimum Unified CM version for this feature is 6.1(3).


The registration behavior is supported on the following SCCP and SIP IP phones and devices:

Cisco Unified IP Phone 7906G

Cisco Unified IP Phone 7911G

Cisco Unified IP Phone 7931G

Cisco Unified IP Phone 7941G

Cisco Unified IP Phone 7941G-GE

Cisco Unified IP Phone 7942G

Cisco Unified IP Phone 7945G

Cisco Unified IP Phone 7961G

Cisco Unified IP Phone 7961G-GE

Cisco Unified IP Phone 7962G

Cisco Unified IP Phone 7965G

Cisco Unified IP Phone 7970G

Cisco Unified IP Phone 7971G-GE

Cisco Unified IP Phone 7975G

Cisco Analog Telephone Adapter

VG248 Gateways

Where to Find More Information

Cisco Unified IP Phone Administration Guide

Cisco Unified Communications Manager Administration Guide

Installation Notes

This section contains these topics:

Installing Firmware Release 8.4(2) for SCCP

Installing Firmware Release 8.4(2) for SIP

Installing Firmware Release for the Cisco Unified IP Phone Expansion Module

Installing Firmware Release 8.4(2) for SCCP

This section describes how to install firmware release 8.4(2) for SCCP.

Firmware Installation Procedure for SCCP

Before using the Cisco Unified IP Phone 7975G, 7965G, 7962G, 7945G, or 7942G with Cisco Unified CallManager release 4.1 or later, you must install the latest firmware on all Cisco Unified Communications Manager servers in the cluster.

To download and install the firmware, follow these steps:

Procedure


Step 1 Go to the following URL:

http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=278875240

Step 2 Log in to the Tools and Resources Download page.

Step 3 Choose the IP Telephony folder by clicking +.

Step 4 Choose IP Phones > Cisco Unified IP Phones 7900 Series.

Step 5 Choose your phone type.

Step 6 To download the firmware for Cisco Unified IP Phone 7975G, 7965G, 7962G, 7945G, or 7942G click one of the following hyperlinks and follow the prompts:

For Cisco Unified CallManager 4.3, 4.2, and 4.1:

Cisco Unified IP Phone 7975G:
cmterm-7975-sccp.8-4-2.exe

Cisco Unified IP Phone 7965G and 7945G:
cmterm-7945_7965-sccp.8-4-2.exe

Cisco Unified IP Phone 7962G and 7942G:
cmterm-7942_7962-sccp.8-4-2.exe

For Cisco Unified CallManager 5.1(1b) and later:

Cisco Unified IP Phone 7975G:
cmterm-7975-sccp.8-4-2.cop.sgn

Cisco Unified IP Phone 7965G and 7945G:
cmterm-7945_7965-sccp.8-4-2.cop.sgn

Cisco Unified IP Phone 7962G and 7942G:
cmterm-7942_7962-sccp.8-4-2.cop.sgn


Note Cisco Unified CallManager versions 5.1(1b) and later require signed cop files.


Step 7 Double-click one of the downloadable files in Step 6, and click the Readme hyperlink, which contains installation instructions for the corresponding firmware:

Cisco Unified IP Phone 7975G:
cmterm-7975-sccp.8-4-2-readme.htm

Cisco Unified IP Phone 7965GG and 7945G:
cmterm-7945_7965-sccp.8-4-2-readme.htm

Cisco Unified IP Phone 7962 and 7942G:
cmterm-7942_7962-sccp.8-4-2-readme.htm

Step 8 Follow the instructions in the Readme file to install the firmware.


Installing Firmware Release 8.4(2) for SIP

This section describes how to install firmware release 8.4(2) for SIP. The SIP version is compatible with Cisco Unified Communications Manager releases 7.0, 6.1, 6.0, and Cisco Unified CallManager release 5.1.

Firmware Installation Procedure for SIP

Before using the Cisco Unified IP Phone 7975G, 7965G, 7962G, 7945G or 7942G with Cisco Unified CallManager 5.1 or later, you must install the latest firmware on all Cisco Unified Communications Manager servers in the cluster.

To download and install the firmware, follow these steps:

Procedure


Step 1 Go to the following URL:

http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=278875240

Step 2 Choose the IP Telephony folder by clicking +.

Step 3 Choose IP Phones > Cisco Unified IP Phones 7900 Series.

Step 4 Choose your phone type.

Step 5 Double-click the following hyperlink, and follow the prompts to download the appropriate firmware for the phone model:

Cisco Unified IP Phone 7975G:
cmterm-7975-sip.8-4-2.cop.sgn

Cisco Unified IP Phone 7965G and 7945G:
cmterm-7945_7965-sip.8-4-2.cop.sgn

Cisco Unified IP Phone 7962G and 7942G:
cmterm-7942_7962-sip.8-4-2.cop.sgn


Note Cisco Unified CallManager versions 5.1(1b) and later require signed cop files.


Step 6 Double-click one of the downloadable files in Step 5, and click the Readme hyperlink, which contains installation instructions for the corresponding firmware:

Cisco Unified IP Phone 7975G:
cmterm-7975-sip.8-4-2-readme.htm

Cisco Unified IP Phone 7965G and 7945G:
cmterm-7945_7965-sip.8-4-2-readme.htm

Cisco Unified IP Phone 7962G and 7942G:
cmterm-7942_7962-sip.8-4-2-readme.htm

Step 7 Follow the instructions in the Readme file to install the firmware.


Installing Firmware Release for the Cisco Unified IP Phone Expansion Module

This section describes how to install a firmware release for the Cisco Unified IP Phone Expansion Module 7916, 7915, or 7914.

Cisco Unified IP Phone Expansion Module 7916 and Cisco Unified IP Phone Expansion Module 7915

Before you use the Cisco Unified IP Phone Expansion Module 7916 or Cisco Unified IP Phone Expansion Module 7915, you must load the expansion module with firmware release B016-1-0-2SR1 or B015-1-0-2, respectively, before using the phone to support relevant 8.4(2) features on your expansion module.


Note The Cisco Unified IP Phones 7975G, 7965G, and 7962G support the Cisco Unified IP Phone Expansion Module 7915 and Cisco Unified IP Phone Expansion Module 7916. You can add a maximum of two expansion modules to these phones.



Note The Cisco Unified IP Phone Expansion Module 7916 and 7915 only support SIP devices in Cisco Unified Communications Manager release 7.0(1).


To download and install the firmware, follow these steps:

Procedure


Step 1 Go to the following URL:

http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=278875240

Step 2 Choose the IP Telephony folder by clicking +.

Step 3 Choose IP Phones > Cisco Unified IP Phones 7900 Series.

Step 4 Choose your expansion module type.

Step 5 To download the firmware for Cisco Unified IP Phone Expansion Module 7915 or Cisco Unified IP Phone Expansion Module 7916, click one of the following hyperlinks and follow the prompts:

For Cisco Unified Communications Manager 6.1(x) and 5.1:

cmterm-7915.1-0-3.cop.sgn

cmterm-7916.1-0-3.cop.sgn

For Cisco Unified CallManager 4.3 and 4.2:

cmterm-7915.1-0-3.exe

cmterm-7916.1-0-3.exe

Step 6 Double-click one of the downloadable files in Step 5, and click the Readme hyperlink, which contains installation instructions for the corresponding firmware:

7915_7916.1-0-3-readme.htm


Cisco Unified IP Phone Expansion Module 7914

If you are using the Cisco Unified IP Phone Expansion Module 7914, you must upgrade the expansion module to firmware release S00105000400 before using the phone to support relevant 8.4(2) features on your expansion module.


Note The Cisco Unified IP Phones 7975G, 7965G, and 7962G support the Cisco Unified IP Phone Expansion Module 7914. You can add a maximum of two Expansion Modules to these phones.



Note The filename for Cisco Unified IP Phone Expansion Module 7914 uses SCCP, however, it supports both SCCP and SIP. This applies to phones using Cisco Unified Communications Manager 7.0.


To download and install the firmware, follow these steps:

Procedure


Step 1 Go to the following URL:

http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=278875240

Step 2 Choose the IP Telephony folder by clicking +.

Step 3 Choose IP Phones > Cisco Unified IP Phones 7900 Series > Cisco Unified IP Phone Expansion Module 7914 > Skinny Client Control Protocol (SCCP) Software.

Step 4 To download the firmware for Cisco Unified IP Phone Expansion Module 7914, click one of the following hyperlinks and follow the prompts:

For Cisco Unified CallManager 4.3 and earlier:

cmterm-7914-sccp.5-0-4.exe

For Cisco Unified CallManager 5.1(1b) and later:

cmterm-7914-sccp.5-0-4.cop.sgn

Step 5 Double-click one of the downloadable files in Step 4, and click the Readme hyperlink, which contains installation instructions for the corresponding firmware:

cmterm-7914-sccp.5-0-4-readme.htm


Important Notes

This section contains these topics:

Initial Startup Time for the Cisco Unified IP Phones

Geometric TCP

Initial Startup Time for the Cisco Unified IP Phones

The initial startup time for Cisco Unified IP Phones in the 8.4(2) firmware will be slightly longer than with previous releases. As more features are introduced with the 8.4(2) firmware, more time is needed to initialize the internal processes. This increase in startup time is only applicable to power cycles and resets of the phone.

Geometric TCP

The Cisco Unified IP Phone firmware 7.2(1) introduced a Geometric TCP mechanism to permit IP Phones to measure the round-trip delay between the IP Phone and Unified CM, then adapt the keepalive timeout value. This provided a very accurate failover mechanism when the network delay is consistent.

However, if the network delay is inconsistent, this mechanism may cause the IP Phones to inaccurately attempt failover. The Cisco Unified IP Phone firmware 8.4(2) introduces the ability for the Network Administrator to disable this behavior, if necessary, through the Detect Unified CM Connection Failure parameter defined on the IP Phone device configuration. The default value is Normal; this Geometric TCP mechanism can be disabled if the parameter is set to Delayed.

Caveats

This section contains these topics:

Using Bug Toolkit

Open Caveats

Resolved Caveats

Using Bug Toolkit

Known problems (bugs) are graded according to severity level. These release notes contain descriptions of:

All severity level 1 or 2 bugs.

Significant severity level 3 bugs.

You can search for problems by using the Cisco Software Bug Toolkit.

To access Bug Toolkit, you need the following items:

Internet connection

Web browser

Cisco.com user ID and password

To use the Software Bug Toolkit, follow these steps:

Procedure


Step 1 To access the Bug Toolkit, go to http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs.

Step 2 Log on with your Cisco.com user ID and password.

Step 3 To look for information about a specific problem, enter the bug ID number in the "Search for bug ID" field, then click Go.


Open Caveats

This section contains these topics:

Open SCCP Caveats

Open SCCP and SIP Caveats

Open SIP Caveats

Open SCCP Caveats

There are no open SCCP caveats for firmware release 8.4(2).

Open SCCP and SIP Caveats

Table 1 lists Severity 1, 2 and 3 defects that are open for the Cisco Unified IP Phone using the SCCP and SIP versions of firmware release 8.4(2).

For more information about an individual defect, you can access the online record for the defect by clicking the Identifier or going to the URL shown. You must be a registered Cisco.com user to access this online information.

Because defect status continually changes, be aware that Table 1 reflects a snapshot of the defects that were open at the time this report was compiled. For an updated view of open defects, access Bug Toolkit as described in the "Using Bug Toolkit" section.

Table 1 Open SCCP and SIP Caveats for the Cisco Unified IP Phone for Firmware Release 8.4(2) 

Identifier
Headline and Bug Toolkit

CSCso00832

Multi-tap Bubble does not display characters properly with THAI locale

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCso00832

CSCso56206

Noise reduction introduces watery-sounding noise

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCso56206

CSCsq80613

User Interface (UI) does not display the last line in Unified CM configuration

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsq80613

CSCsr43681

CallBack does not work properly when directory or messages are on focus

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsr43681

CSCsu01228

Crackling or static noise is heard on Cisco Unified IP Phone 7975G

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsu01228

CSCsu77742

Changing TFTP server after unlocking control files do not reset Cisco Unified IP Phone to new TFTP server

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsu77742

CSCsu96371

Cisco Unified IP Phone does not strip tag configured in PC VLAN

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsu96371

CSCsv01316

Cisco Unified IP Phone can only place or answer a call using a softkey

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv01316

CSCsv32103

Cisco Unified IP Phone (SIP) does not send INVITE(hold) message on BiB call with silent monitoring

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv32103

CSCsv36246

Callback UI with incorrect icon does not get cleared after directory number is dialed

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv36246

CSCsv41894

Cisco Unified IP Phone mediaStream receive volume and basic call mixing bug

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv41894

CSCsv42063

`Call back' message is incorrect when Java is configured under message context

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv42063

CSCsv42210

`Call back' notification will not come to front

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv42210

CSCsv48350

Cisco Unified IP Phone cannot register to Unified CM after changing Cisco Discovery Protocol (CDP) setting on network port

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv48350

CSCsv50978

Call Back `Dial' softkey does not work when speaker is disabled

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv50978

CSCsv51230

Press `<<` allows the `Save' softkey to be active while setting 802.1x password

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv51230

CSCsv54006

Service page exits automatically when call is made from Fastdial

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv54006

CSCsv54188

Two Cisco Unified IP Phones cbarge in shared line at the same time, one fails

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv54188

CSCsv58992

Directory service partly fails when failover occurs

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv58992

CSCsv61474

Cisco Unified IP Phone does not take subscriber as standby Unified CM when fallback from subscriber to publisher

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv61474

CSCsv63782

Light status is incorrect when configuration `Auto answer' is on shared line

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv63782

CSCsv63858

Phone log out Personal Directory when dialing a Fastdial directory number

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv63858

CSCsv66401

Virtual Player is not supported if service vendor is Cisco Systems, Inc.

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv66401


Open SIP Caveats

Table 2 lists Severity 1, 2 and 3 defects that are open for the Cisco Unified IP Phone using the SIP version of firmware release 8.4(2).

For more information about an individual defect, you can access the online record for the defect by clicking the Identifier or going to the URL shown. You must be a registered Cisco.com user to access this online information.

Because defect status continually changes, be aware that Table 2 reflects a snapshot of the defects that were open at the time this report was compiled. For an updated view of open defects, access Bug Toolkit as described in the "Using Bug Toolkit" section.

Table 2 Open SIP Caveats for the Cisco Unified IP Phone for Firmware Release 8.4(2) 

Identifier
Headline and Bug Toolkit

CSCso49790

Cisco Unified IP Phone (SIP) has no alert name in Placed Calls history

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCso49790

CSCsr70882

Cisco Unified IP Phone (SIP) occasionally has garbled speech path with G.729 codec

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsr70882


Resolved Caveats

This section contains these topics:

Resolved SCCP Caveats

Resolved SCCP and SIP Caveats

Resolved SIP Caveats

Resolved SCCP Caveats

There are no resolved SCCP caveats for firmware release 8.4(2).

Resolved SCCP and SIP Caveats

Table 3 lists Severity 1, 2 and 3 defects that are resolved for the Cisco Unified IP Phone using the SCCP and SIP versions of firmware release 8.4(2).

For more information about an individual defect, you can access the online record for the defect by clicking the Identifier or going to the URL shown. You must be a registered Cisco.com user to access this online information.

Because defect status continually changes, be aware that Table 3 reflects a snapshot of the defects that were resolved at the time this report was compiled. For an updated view of resolved defects, access Bug Toolkit as described in the "Using Bug Toolkit" section.

Table 3 Resolved SCCP and SIP Caveats for the Cisco Unified IP Phone
7975G, 7965G, 7945G, 7962G and 7942G for Firmware Release 8.4(2) 

Identifier
Headline

CSCsk83382

Cisco Unified IP Phone update needed for Venezuela time zone change

CSCsm13939

Second line gets focus when Busy Lamp Field (BLF) with button is pressed.

CSCsm56180

JAl interaction with conference feature fails to complete conference

CSCso26500

Failed to blind transfer a call during a conference

CSCsq58044

Inconsistency between alerting name and placed call on screen display

CSCsq83332

Cisco Unified IP Phone 7961G-GE, 7962G, 7942G, and 7941G UI does not refresh the soft key clearly

CSCsq86253

Cisco Unified IP Phone sends incorrect Unified CM name when DHCP Domain Name Servers (DNS) have 63 entries

CSCsq88576

Cisco Unified IP Phone incorrectly pads frames less than 64 bytes

CSCsr07269

Call through H.323 ICT, holds call, resumes, and drops call

CSCsr14566

Hash table enumerator when using IPPM gives error

CSCsr22771

Double DHCP request send out by Cisco Unified IP Phone

CSCsr39509

Memory leak in font support code detected

CSCsr55945

Cisco Unified IP Phone queries the primary TFTP server twelve times before failing over to secondary

CSCsr69637

Intercom call will be dropped when there is a pre-dial number

CSCsr73685

Cannot end barge call when `EndCall' softkey is not in first page

CSCsr96183

Cisco Unified IP Phone stops receiving mulitcast audio after few times

CSCsu07181

Cannot dial from Directories menu after exiting from `EditDial'

CSCsu11357

Third generation Cisco Unified IP Phones do not take Argentina time zone

CSCsu18154

Cisco Unified IP Phone prompts as `line in use' but all lines are in idle state

CSCsu33043

Disabling the speakerphone does not take effect after Cisco Unified IP Phone fallback

CSCsu38132

CTI controlled Cisco Unified IP Phone generates incorrect DTMF

CSCsu43219

En-bloc feature causes non-dialable characters to be dialed

CSCsu47935

`HTTP GET' with `ACCEPT' header over 300 characters causes `400 Bad Request' message

CSCsu52580

Cisco Unified IP Phone does not set `secs' field in `DHCPDiscover' message

CSCsu67742

Intercom call timer reset to `0' when settings menu is accessed during active call

CSCsu93940

Cisco Unified IP Phone fails to register to Windows Unified CM working in mixed mode

CSCsv01132

Cisco Unified IP Phone resets when barging into conference

CSCsv04751

DTMF is not squelched on Cisco Unified IP Phones, causing duplicate DTMF

CSCsv11576

Incorrect softkey is displayed in `Call Details' when speaker is disabled


Resolved SIP Caveats

Table 4 lists Severity 1, 2 and 3 defects that are resolved for the Cisco Unified IP Phone using the SIP versions of firmware release 8.4(2).

For more information about an individual defect, you can access the online record for the defect by clicking the Identifier or going to the URL shown. You must be a registered Cisco.com user to access this online information.

Because defect status continually changes, be aware that Table 4 reflects a snapshot of the defects that were resolved at the time this report was compiled. For an updated view of resolved defects, access Bug Toolkit as described in the "Using Bug Toolkit" section.

Table 4 Resolved SIP Caveats for the Cisco Unified IP Phone
7975G, 7965G, 7945G, 7962G and 7942G for Firmware Release 8.4(2) 

Identifier
Headline and Bug Toolkit Link

CSCsr01092

No way to place a call on secondary line of Cisco Unified IP Phone (SIP)


Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.