Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.6 (SIP)
Cisco Unified IP Phone Non-Lockable Wall Mount
Downloads: This chapterpdf (PDF - 3.96MB) The complete bookPDF (PDF - 15.26MB) | Feedback

Cisco Unified IP Phone Non-Lockable Wall Mount

Table Of Contents

Cisco Unified IP Phone Non-Lockable Wall Mount

ADA Non-Lockable Wall Mount Kit for 8961 Series and 9900 Series IP Phones

Components

Before you begin

Install Non-Lockable Wall Mount for phone

Remove Phone from Non-Lockable Wall Mount

ADA Non-Lockable Wall Mount Kit for 8961 Series and 9900 Series IP Phones with Key Expansion Module

Components

Before You Begin

Install Non-Lockable Wall Mount Kit for Phone with Key Expansion Module

Remove Phone and Key Expansion Module from Non-Lockable Wall Mount


Cisco Unified IP Phone Non-Lockable Wall Mount


This appendix contains information about installing the wall mount for use with the following products:

ADA Non-Lockable Wall Mount Kit for 8961 Series and 9900 Series IP Phones: Installed on the Cisco Unified IP Phone 8961, 9951, and 9971.

ADA Non-Lockable Wall Mount Kit for 8961 Series and 9900 Series IP Phones plus a single Key Expansion Module: Installed on the Cisco Unified IP Phone 8961, 9951, and 9971 with the Key Expansion Module.

These nonlocking wall mount kits meet ADA 4.4.1 requirements.

ADA Non-Lockable Wall Mount Kit for 8961 Series and 9900 Series IP Phones

This section describes how to install the non-lockable wall mount kit on a Cisco Unified IP Phone 8961, 9951, and 9971 when the phone is not connected to a Key Expansion Module.

The following figure shows the wall mount kit installed on the phone.

Figure F-1 Back View of ADA Non-Lockable Wall Mount Kit Installed on Phone

The following figure shows the phone with the wall mount kit from the side.

Figure F-2 Side View of ADA Non-Lockable Wall Mount Kit Installed on Phone

Components

The following figure shows the components of the ADA Non-Lockable Wall Mount Kit for 8961 Series and 9900 Series IP Phones.

Figure F-3 Components

The package contains the following items:

One phone bracket

One wall bracket

Four #8-18 x 1.25-inch Phillips-head screws with four anchors

Two #4-40 x 0.31-inch machine screws

One 6-inch Ethernet cable

Before you begin

You need these tools to install the bracket:

#1 and #2 Phillips-head screwdrivers

Level

Pencil

You must also install an Ethernet jack for the telephone in the desired location if an Ethernet jack does not currently exist. This jack must be wired appropriately for an Ethernet connection. You cannot use a regular telephone jack. For more information about phone installation requirements and warnings, see Setting Up the Cisco Unified IP Phone.

Install Non-Lockable Wall Mount for phone

The wall mount kit can be mounted on most surfaces, including concrete, brick, and similar hard surfaces. To mount the kit on concrete, brick, or similar hard surfaces, you must provide the appropriate screws and anchors for your wall surface.

Procedure


Step 1 Mount the wall bracket in the desired location. You can install the bracket over an Ethernet jack, or you can run the Ethernet network cable to a jack nearby.


Note If the jack is to be placed behind the phone, the Ether net jack must be flush to the wall or recessed.


a. Hold the bracket on the wall, placing it so that the arrow on the back of the bracket is pointing up.

b. Use the level to ensure the bracket is level, then use a pencil to mark the screw holes.

c. Using a #2 Phillips-head screwdriver, carefully center the anchor over the pencil mark and press the anchor into the wall.

d. Screw the anchor clockwise into the wall until it is seated flush.

e. Use the included screws and a #2 Phillips-head screwdriver to attach the bracket to the wall.

The following figure shows the bracket installation steps.

Figure F-4 Mount the Wall Bracket

Step 2 Attach the phone bracket to the IP Phone.

a. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached cords from the base of the phone.

b. Remove the label covers that are concealing the screw holes.

c. Attach the phone bracket by inserting the tabs into the mounting tabs on the phone. The ports of the phone should be accessible through the holes in the bracket.

d. Secure the phone bracket to the IP Phone with the machine screws, using the #1 Phillips-head screw driver.

e. Thread the handset cord (and headset cord, if using one). Reattach the cords and seat them in the clips incorporated into the phone body.

The following figure shows how the bracket attaches to the phone.

Figure F-5 Attach the Phone Bracket

Step 3 Attach the cables to the phone:

a. Attach the Ethernet cable to the 10/100/1000 SW network port and wall jack.

b. (Optional) If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100/1000 Computer (PC access) port.

c. (Optional) If you are using an external power supply, plug the power cord into the phone and dress the cord by clipping it into the clips that are incorporated into the phone body next to the PC port.

d. (Optional) If the cables terminate inside the wall bracket, connect the cables to the jacks.

The following figure shows the cables.

Figure F-6 Attach cables

Step 4 Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots on the wall bracket.

For cables that terminate outside of the brackets, use the cable-access openings in the bottom of the bracket to position the power cord and any other cable that does not terminate in the wall behind the bracket. The phone and wall bracket openings together form circular openings with room for one cable per opening.

The following figure shows how you attach the phone to the wall bracket.

Figure F-7 Attach phone to wall bracket

Step 5 Press the phone firmly into the wall bracket and slide the phone down. The tabs in the bracket click into position.

Step 6 Proceed to Step 3 of Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971.


Remove Phone from Non-Lockable Wall Mount

The phone mounting plate contains two tabs to lock the plate into the wall bracket. The following figure shows the location and shape of the tabs.

Figure F-8 Figure 23: Tab location

To remove the phone and mounting plate from the wall bracket, you must disengage these tabs.

Before You Begin

You require 2 screwdrivers or metal rods.


Step 1 Push the screw drivers into the left and right holes in the phone mounting plate approximately 1 in. (2.5 cm).

Step 2 Lift the screwdriver handles up to put a downward pressure on the tabs.

Figure F-9 Disengage tabs

Step 3 Press firmly to disengage the tabs and lift the phone at the same time to release the phone from the wall bracket.


ADA Non-Lockable Wall Mount Kit for 8961 Series and 9900 Series IP Phones with Key Expansion Module

This section describes how to install the non-lockable wall mount kit on a Cisco Unified IP Phone 8961, 9951, and 9971 when the phone is connected to a Key Expansion Module.

The following figure shows the wall mount kit installed on the phone.

Figure F-10 Back View of ADA Non-Lockable Wall Mount Kit Installed on Phone with Key Expansion Module

The following figure shows the phone with the wall mount kit from the side.

Figure F-11 Side View of ADA Non-Lockable Wall Mount Kit Installed on Phone with Key Expansion Module

Components

The following figure shows the components of the ADA Non-Lockable Wall Mount Kit for the Cisco Unified IP Phone 8961, 9951, and 9971 with a Key Expansion Module.

Figure F-12 Components

The package contains the following items:

One phone bracket

One wall bracket

Six #8-18 x 1.25-inch Phillips-head screws with six anchors

Three #4-40 x 0.31-inch machine screws

One 6-inch Ethernet cable

Before You Begin

You need these tools to install the bracket:

#1 and #2 Phillips-head screwdrivers

Level

Pencil

You must also install an Ethernet jack for the telephone in the desired location if an Ethernet jack does not currently exist. This jack must be wired appropriately for an Ethernet connection. You cannot use a regular telephone jack. For more information about phone installation requirements and warnings, see Setting Up the Cisco Unified IP Phone and Setting Up the Cisco Unified IP Color Key Expansion Module.

Install Non-Lockable Wall Mount Kit for Phone with Key Expansion Module

The wall mount kit can be mounted on most surfaces, including concrete, brick, and similar hard surfaces. To mount the kit on concrete, brick, or similar hard surfaces, you must provide the appropriate screws and anchors for your wall surface.


Note Be sure to connect to connect the Cisco Unified IP Phone to the Key Expansion Module before installing the phone bracket.



Step 1 Mount the wall bracket in the desired location. You can install the bracket over an Ethernet jack, or you can run the Ethernet network cable to a nearby jack.


Note If the jack is to be placed behind the phone, the Ethernet jack must be flush to the wall or recessed.


a. Hold the bracket on the wall. See the following figure for the orientation of the wall bracket.

b. Use the level to ensure that the bracket is level and use a pencil to mark the screw holes.

c. Using a #2 Phillips-head screwdriver, carefully center the anchor over the pencil mark and press the anchor into the wall.

d. Screw the anchor clockwise into the wall until it is seated flush.

e. Use the included screws and a #2 Phillips-head screwdriver to attach the bracket to the wall.

The following figure shows the steps for installing the bracket.

Figure F-13 Bracket Installation

Step 2 Attach the phone bracket to the IP phone and key expansion assembly.

a. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached cords from the base of the phone

b. Remove the label covers that are conceal the screw holes.

c. Attach the phone bracket by inserting the tabs into the mounting tabs on the back of the phone. The phone ports should be accessible through the holes in the bracket.

d. Secure the phone bracket to the IP phone with the machine screws using a #1 Philips-head screwdriver.

e. Thread the handset cord (and headset cord, if using one). Reattach the cords and seat them in the clips that are incorporated into the phone body.

The headset and handset connectors should be accessible from outside the wall mount bracket.

The following figure shows the steps to attach the phone bracket.

Figure F-14 Attach Phone Bracket

Step 3 Attach the cords.

a. Attach the Ethernet cable to the 10/100/1000 SW network port and wall jack.

b. (Optional) If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100/1000 Computer (PC access) port.

c. (Optional) If you are using an external power supply, plug the power cord into the phone and dress the cord by clipping it into the clips that are incorporated into the phone body next to the PC port.

d. (Optional) If the cables terminate inside the wall bracket, connect the cables to the jacks.

The following figure shows the cables.

Figure F-15 Attach Cables

Step 4 Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots on the wall bracket.

For cables that terminate outside of the bracket, use the cable-access openings in the bottom of the bracket to position the power cord and any other cable that does not terminate in the wall behind the bracket. The phone and wall bracket openings together form circular openings with room for one cable per opening.

Figure F-16 Attach Phone to Wall Bracket

Step 5 Proceed to Step 3 of Installing a Wall Mount for a Phone with a Key Expansion Module.


Remove Phone and Key Expansion Module from Non-Lockable Wall Mount

The phone mounting plate contains two tabs to lock the plate into the wall bracket. The following figure shows the location and shape of the tabs.

Figure F-17 Tab Location

To remove the phone and mounting plate from the wall bracket, you must disengage these tabs.

Before You Begin

You require two screwdrivers or metal rods.


Step 1 Push the screw drivers into the left and right holes in the phone mounting plate until you feel resistance.

Step 2 Press firmly inwards (towards the phone) to disengage the tabs, lift up on the phone to release the phone from the wall bracket, and then pull the phone towards you.

Figure F-18 Disengage Tabs