Cisco Unified IP Phone 7975G Administration Guide for Cisco Unified Communications Manager 6.1
Appendix D: Technical Specifications
Downloads: This chapterpdf (PDF - 343.0KB) The complete bookPDF (PDF - 7.2MB) | Feedback

Technical Specifications

Table Of Contents

Technical Specifications

Physical and Operating Environment Specifications

Cable Specifications

Network and Access Port Pinouts


Technical Specifications


The following sections describe the technical specifications for the Cisco Unified IP Phone 7975G.

Physical and Operating Environment Specifications

Cable Specifications

Network and Access Port Pinouts

Physical and Operating Environment Specifications

Table D-1 shows the physical and operating environment specifications for the Cisco Unified IP Phone.

Table D-1 Physical and Operating Specifications 

Specification
Value or Range

Operating temperature

32° to 104°F (0° to 40°C)

Operating relative humidity

10% to 95% (non-condensing)

Storage temperature

14° to 140°F (-10° to 60°C)

Height

9.07 in. (23.03 cm)

Width

10.82 in. (27.48 cm)

Depth

2.54 in. (6.45 cm)—with footstand fully closed

6.0 in. (15.24 cm)—with footstand fully open

3.54 in. (9.00 cm)—with optional wall mount kit

Weight

3.25 lb (1.47 kg)

Power Options

100-240 VAC, 50-60 Hz, 0.5 A—when using the AC adapter

44V-57V DC, 0.25 A—when using the in-line power over the network cable

Cables

Category 3/5/5e/6 for 10-Mbps cables with 4 pairs
Category 5/5e/6 for 100-Mbps cables with 4 pairs
Category 5e/6 for 1000-Mbps cables with 4 pairs

Note Cables have 4 pairs of wires for a total of 8 conductors.

Distance Requirements

As supported by the Ethernet Specification, it is assumed that the maximum cable length between each Cisco Unified IP Phone and the switch is 100 meters (330 feet).


Cable Specifications

RJ-9 jack (4-conductor) for handset and headset connection.

RJ-45 jack for the LAN 10/100/1000BaseT connection (labeled 10/100/1000 SW).

RJ-45 jack for a second 10/100/1000BaseT compliant connection (labeled 10/100/1000 PC).

48-volt power connector.

Network and Access Port Pinouts

Although both the network and access ports are used for network connectivity, they serve different purposes and have different port pinouts.

The network port is labeled 10/100/1000 SW on the Cisco Unified IP Phone.

The access port is labeled 10/100/1000 PC on the Cisco Unified IP Phone.

Network Port Connector

Table D-2 describes the network port connector pinouts.

Table D-2 Network Port Connector Pinouts 

Pin Number
Function

1

BI_DA+

2

BI_DA-

3

BI_DB+

4

BI_DC+

5

BI_DC-

6

BI_DB-

7

BI_DD+

8

BI_DD-

Note "BI" stands for bi-directional, while DA, DB, DC and DD stand for "Data A", "Data B", "Data C" and "Data D", respectively.


Access Port Connector

Table D-3 describes the access port connector pinouts.

Table D-3 Access Port Connector Pinouts

Pin Number
Function

1

BI_DB+

2

BI_DB-

3

BI_DA+

4

BI_DD+

5

BI_DD-

6

BI_DA-

7

BI_DC+

8

BI_DC-

Note "BI" stands for bi-directional, while DA, DB, DC and DD stand for "Data A", "Data B", "Data C" and "Data D", respectively.