Cisco Unified IP Phone 7941G, 7941G-GE, 7942, 7961G, 7961G-GE, and 7962 User Guide for Cisco Unified Communications Manager 9.0 (SCCP and SIP)
Handset, Headset, and Speakerphone
Downloads: This chapterpdf (PDF - 1.15MB) The complete bookPDF (PDF - 3.59MB) | The complete bookePub (ePub - 671.0KB) | Feedback

Handset, Headset, and Speakerphone

Handset, Headset, and Speakerphone

Headset, Handset, and Speaker Overview

You can use your phone with these audio devices: a handset, headset, or speakerphone.

The phone is off-hook when the handset is lifted or another audio device is in use.

The phone is on-hook when the handset is in its cradle and other audio devices are not in use.

Handset

The following table describes how to use the handset.

If you want to...

Then...

Use the handset

Lift it to go off-hook; replace it to go on-hook.

The ringing line is automatically selected. Contact your system administrator about options to always select the primary line.

Switch to the speakerphone or a headset during a call

Press or (), then hang up the handset.

Adjust the volume level for a call

Press the Volume button during a call or after invoking a dial tone.

Press Save to preserve the volume level for future calls.

Headset

Your phone supports four- or six-wire headset jacks for wired headsets. Cisco Unified IP Phones 7962G and 7942G also support wireless headsets. For information about purchasing headsets, see Wired and Wireless Headsets.

You can use a headset with all of the controls on your phone, including and .

However, if you use a wireless headset, refer to the wireless headset documentation for instructions.

If you want to...

Then...

Toggle headset mode on and off

Press .

Switch to a handset

Lift the handset.

Adjust the volume level for a call

Press during a call or after invoking a dial tone.

Press Save to preserve the volume level for future calls.

If you use AutoAnswer, see AutoAnswer with Headset or Speakerphone.

Your system administrator can set up your phone to record a conversation between you (on your headset), a supervisor (on the phone handset), and your connected party.

Control Wired Headset Sidetone

When you speak on a telephone using a headset, the sound picked up by the headset microphone can be sent back through the headset speaker. This creates a low-level feedback, known as sidetone. The wired headsets can result in sidetone . Different wired headsets require different sidetone and settings. You need to select the best sidetone level for the wired headset you use.

Procedure
    Step 1   Press .
    Step 2   Use the Preferences menu and navigate to Headset Sidetone.
    Step 3   Select Headset Sidetone.
    Step 4   Select one of the sidetone levels:
    • High
    • Normal
    • Low
    • Very Low
    • Off
    Step 5   Press Save or press Cancel.

    Wireless Headset

    Cisco Unified IP Phones 7962G and 7942G support wireless headsets. Refer to the wireless headset documentation for information about using the wireless headset’s remote features. Also, check with your system administrator to be sure your phone is enabled to use a wireless headset with the wireless headset remote hookswitch control feature.

    Wideband Headset

    If you use a headset that supports wideband, you may experience improved audio sensitivity if you enable the wideband setting on your phone (this setting is disabled by default). To access the setting, choose > User Preferences > Audio Preferences > Wideband Headset.

    If the Wideband Headset setting is dimmed, then you cannot control this setting.

    Check with your system administrator to be sure your phone system is configured to use wideband. If the system is not configured for wideband, you may not detect any additional audio sensitivity even when using a wideband headset. To learn more about your headset, refer to the headset documentation or contact your system administrator for assistance.

    Speakerphone

    If the handset is in its cradle and is not lit, many of the actions you can take to dial a number or answer a call will trigger speakerphone mode automatically.

    If you want to...

    Then...

    Toggle speakerphone mode on or off

    Press .

    Switch to a handset

    Lift the handset.

    Adjust the volume level for a call

    Press during a call or after invoking a dial tone.

    Press Save to preserve the volume level for future calls.

    AutoAnswer with Headset or Speakerphone

    When AutoAnswer is enabled, your phone answers incoming calls automatically after a few rings. Your system administrator configures AutoAnswer to use either the speakerphone or a headset. You may use AutoAnswer if you receive a high volume of incoming calls.

    If you...

    Then...

    Use AutoAnswer with a headset

    Keep headset mode active (in other words, keep illuminated), even when you are not on a call.

    To keep headset mode active, perform the following actions:

    • Press EndCall to hang up.
    • Press New Call or Dial to place new calls.

    If your phone is set up to use AutoAnswer in headset mode, calls are automatically answered only if is illuminated.

    Otherwise, calls ring normally and you must manually answer them.

    Use AutoAnswer with the speakerphone

    Keep the handset in the cradle and headset mode inactive ( unlit).

    Otherwise, calls ring normally and you must manually answer them.

    Tip

    AutoAnswer is disabled when the Do Not Disturb feature is active.