Cisco Unified IP Phone 7962G, 7942G, 7961G, 7961G-GE, 7941G, and 7941G-GE Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
Setting Up the Cisco Unified IP Phone
Downloads: This chapterpdf (PDF - 1.04MB) The complete bookPDF (PDF - 7.28MB) | Feedback

Setting Up the Cisco Unified IP Phones

Table Of Contents

Setting Up the Cisco Unified IP Phones

Before You Begin

Network Requirements

Cisco Unified Communications Manager Configuration

Understanding the Cisco Unified IP Phone Components

Network and Access Ports

Handset

Speakerphone

Headset

Audio Quality

Connecting a Headset

Disabling a Headset

Enabling a Wireless Headset on the Cisco Unified IP Phones

Using External Devices

Installing the Cisco Unified IP Phones

Attaching a Cisco Unified IP Phone Expansion Module

Feature Key Capacity Increase for Cisco Unified IP Phones

Adjusting the Placement of the Cisco Unified IP Phone

Adjusting Cisco Unified IP Phone Placement on the Desktop

Securing the Phone with a Cable Lock

Mounting the Phone to the Wall

Verifying the Phone Startup Process

Configuring Startup Network Settings

Configuring Security on the Cisco Unified IP Phones


Setting Up the Cisco Unified IP Phones


This chapter includes the following topics, which help you install the Cisco Unified IP Phones on an IP telephony network:

Before You Begin

Understanding the Cisco Unified IP Phone Components

Installing the Cisco Unified IP Phones

Attaching a Cisco Unified IP Phone Expansion Module

Feature Key Capacity Increase for Cisco Unified IP Phones

Verifying the Phone Startup Process

Configuring Startup Network Settings

Configuring Security on the Cisco Unified IP Phones


Note Before you install a Cisco Unified IP Phone, you must decide how to configure the phone in your network. Then you can install the phone and verify its functionality. For more information, see Preparing to Install the Cisco Unified IP Phones on Your Network.


Before You Begin

Before installing the Cisco Unified IP Phone, review the requirements in these sections:

Network Requirements

Cisco Unified Communications Manager Configuration

Network Requirements

For the Cisco Unified IP Phone to successfully operate as a Cisco Unified IP Phone endpoint in your network, your network must meet the following requirements:

Working Voice over IP (VoIP) Network:

VoIP configured on your Cisco routers and gateways

Cisco Unified Communications Manager installed in your network and configured to handle call processing

IP network that supports DHCP or manual assignment of IP address, gateway, and subnet mask


Note The Cisco Unified IP Phone displays the date and time from Cisco Unified Communications Manager. If the Cisco Unified Communications Manager server is located in a different time zone than the phones, the phones will not display the correct local time.


Cisco Unified Communications Manager Configuration

The Cisco Unified IP Phone requires Cisco Unified Communications Manager to handle call processing. See Cisco Unified Communications Manager Administration Guide or to context-sensitive help in the Cisco Unified Communications Manager application to ensure that Cisco Unified Communications Manager is set up properly to manage the phone and to properly route and process calls.

If you plan to use auto-registration, verify that it is enabled and properly configured in Cisco Unified Communications Manager before connecting any Cisco Unified IP Phone to the network. For information about enabling and configuring auto-registration, see Cisco Unified Communications Manager Administration Guide. Also, see Adding Phones to the Cisco Unified Communications Manager Database.

You must use Cisco Unified Communications Manager to configure and assign telephony features to the Cisco Unified IP Phones. See Telephony Features Available for the Cisco Unified IP Phone for details.

In Cisco Unified Communications Manager, you can add users to the database and associate them with specific phones. In this way, users gain access to web pages that allow them to configure items such as call forward, speed dial, and voice message system options. See Adding Users to Cisco Unified Communications Manager for details.

Understanding the Cisco Unified IP Phone Components

The Cisco Unified IP Phones include these components on the phone or as accessories for the phone:

Network and Access Ports

Handset

Speakerphone

Headset

Network and Access Ports

The back of the Cisco Unified IP Phones includes these ports:

Network port

Labeled 10/100 SW on the 7962G, 7942G, 7961G, and 7941G

Labeled 10/100/1000 SW on the 7961G-GE and 7941G-GE

Access port

Labeled 10/100 PC on the 7962G, 7942G, 7961G, and 7941G

Labeled 10/100/1000 PC on the 7961G-GE and 7941G-GE

Each port supports 10/100 or 10/100/1000 Mbps half- or full-duplex connections to external devices.

For the Cisco Unified IP Phones 7962G and 7942G, you can use either Category 3/5/5e cabling for 10-Mbps connections, but you must use Category 5 or 5e for 100 Mbps connections.

For the Cisco Unified IP Phones 7961G, 7961G-GE, 7941G, and 7941G-GE, you can use either Category 3 or 5 cabling for 10-Mbps connections, but you must use Category 5 for 100 and 1000 Mbps connections.

Use the SW network port to connect the phone to the network. You must use a straight-through cable on this port. The phone can also obtain inline power from a switch over this connection. See Providing Power to the Cisco Unified IP Phones for details.

Use the PC access port to connect a network device, such as a computer, to the phone. You must use a straight-through cable on this port.

Handset

The wideband-capable handset is designed especially for use with a Cisco Unified IP Phone. It includes a light strip that indicates incoming calls and voice messages waiting.

To connect the handset to the Cisco Unified IP Phones 7962G and 7942G, plug the cable into the handset and the Handset port on the back of the phone.

To connect the handset to the Cisco Unified IP Phones 7961G, 7961G-GE, 7941G, and 7941G-GE, remove the hookswitch clip (see Figure 3-1) from the cradle area. Then plug the cable into the handset and into the Handset port on the back of the phone.

Figure 3-1 Removing the Hookswitch Clip

Speakerphone

By default, the wideband-capable speakerphone is enabled on the Cisco Unified IP Phone.

You can disable the speakerphone by using Cisco Unified Communications Manager Administration. To do so, choose Device > Phone and locate the phone you want to modify. In the Phone Configuration window for the phone, check the Disable Speakerphone check box.

Headset

Although Cisco Systems performs internal testing of third-party headsets for use with the Cisco Unified IP Phones, Cisco does not certify or support products from headset or handset vendors.

We recommend that the use of good quality external devices, for example, headsets that are screened against unwanted radio frequency (RF) and audio frequency (AF) signals. Depending on the quality of headsets and their proximity to other devices such as cell phones and two-way radios, some audio noise or echo may still occur. An audible hum or buzz may be heard by either the remote party or by both the remote party and the Cisco Unified IP Phone user. Humming or buzzing sounds can be caused by a range of outside sources; for example, electric lights, electric motors, or large PC monitors. See Using External Devices, for more information.


Note In some cases, hum can be reduced or eliminated by using a local power cube or power injector.


These environmental and hardware inconsistencies in the locations where Cisco Unified IP Phones are deployed means that there is not a single headset solution that is optimal for all environments.

We recommend that customers test headsets in their intended environment to determine performance before making a purchasing decision and deploying en masse.


Note The Cisco Unified IP Phones support wideband headsets.


Audio Quality

Beyond its physical, mechanical and technical performance, the audio portion of a headset must sound good to the user and to the party on the far end. Sound quality is subjective and Cisco cannot guarantee the performance of any headsets. However, a variety of headsets from leading headset manufacturers have been reported to perform well with Cisco Unified IP Phones.

For more information, see http://www.cisco.com/en/US/partner/prod/voicesw/ucphone_headsets.html.

Connecting a Headset

To connect a wired headset to the Cisco Unified IP Phone, plug it into the Headset port on the back of the phone. Press the Headset button on the phone to place and answer calls using the headset.

You can use the wired headset with all of the features on the Cisco Unified IP Phone, including the Volume and Mute buttons. Use these buttons to adjust the ear piece volume and to mute the speech path from the headset microphone.

See the wireless headset documentation for information about connecting the headset and using the features.

Disabling a Headset

You can disable the headset by using Cisco Unified Communications Manager Administration. If you do so, you also will disable the speakerphone.

To disable the headset from Cisco Unified Communications Manager Administration, perform the following actions:

Procedure


Step 1 Choose Device > Phone and locate the phone that you want to modify.

Step 2 Check the Disable Speakerphone and Headset check box in the Phone Configuration window.


Enabling a Wireless Headset on the Cisco Unified IP Phones

By default, the Wireless Headset Hookswitch Control option is disabled. You can enable the option in the Cisco Unified Communications Manager Administration application.

See the wireless headset documentation for information about connecting the headset and using the features.

Modifying the Headset Hookswitch Control

Procedure


Step 1 Choose Device > Phone and locate the phone you want to modify.

Step 2 Select Enable for Headset Hookswitch Control, in the Phone Configuration window.


Verifying the Wireless Headset Hookswitch Control

Procedure


Step 1 Choose Settings > Device Configuration > Media Configuration to verify that the feature is enabled.

Step 2 Select Enable to verify that the Wireless Headset Hookswitch Control is set.


Using External Devices

The following information applies when you use external devices with the Cisco Unified IP Phone.

We recommend the use of good quality external devices that are shielded (screened) against unwanted radio frequency (RF) and audio frequency (AF) signals.

Depending on the quality of these devices and their proximity to other devices such as mobile phones or two-way radios, some audio noise may still occur. In these cases, We recommend that you take one or more of the following actions:

Move the external device away from the source of the RF or AF signals.

Route the external device cables away from the source of the RF or AF signals.

Use shielded cables for the external device, or use cables with a better shield and connector.

Shorten the length of the external device cable.

Apply ferrites or other such devices on the cables for the external device.

Cisco cannot guarantee the performance of the system because Cisco has no control over the quality of external devices, cables, and connectors. The system performs adequately when suitable devices are attached using good quality cables and connectors.


Caution In European Union countries, use only external headsets that are fully compliant with the EMC Directive [89/336/EC].

Installing the Cisco Unified IP Phones

You must connect the Cisco Unified IP Phone to the network and to a power source before using it. See Figure 3-2 for a graphical representation of the connections.


Note Before you install a phone, even if it is new, upgrade the phone to the current firmware image. Before using external devices, read the Using External Devices for safety and performance information.


Before You Begin

Remove the hookswitch clip (see Handset) from the cradle area.

To install a Cisco Unified IP Phone, perform the tasks described in Table 3-1:

Table 3-1 Installing the Cisco Unified IP Phone 7962G and 7942G 

Task
Purpose
Related Topics

1.

Connect the handset to the Handset port.

2.

Connect a headset to the Headset port.

Optional. You can add a headset later if you do not connect one now.

See Headset for supported headsets.

3.

(Cisco Unified IP Phones 7962G and 7942G only)

Connect a wireless headset.

Optional. You can add a wireless headset later if you do not want to connect one now.

See the wireless headset documentation for information.

4.

(Optional) Connect the power supply to the Cisco DC Adapter port.

See Adding Phones to the Cisco Unified Communications Manager Database for guidelines.

5.

Connect a straight-through Ethernet cable from the switch to the network port labeled 10/100 SW on the Cisco Unified IP Phones 7962G, 7942G, 7961G, and 7941G, or to the network port labeled 10/100/1000 SW on the Cisco Unified IP Phones 7961G-GE and 7941G-GE.

Each Cisco Unified IP Phone ships with one Ethernet cable in the box.

You can use either Category 3/5/5e cabling for 10-Mbps connections, but you must use Category 5/5e for 100 Mbps connections.

See Network and Access Ports for guidelines.

6.

Connect a straight-through Ethernet cable from another network device, such as a desktop computer, to the access port labeled 10/100 PC port on the Cisco Unified IP Phones 7962G, 7942G, 7961G, and 7941G, or to the network port labeled 10/100/1000 PC on the Cisco Unified IP Phones 7961G-GE and 7941G-GE.

(Optional) You can connect another network device later if you do not connect one now.

You can use either Category 3/5/5e cabling for 10-Mbps connections, but you must use Category 5/5e for 100 Mbps connections.

See Network and Access Ports for guidelines.


Figure 3-2 Cisco Unified IP Phone 7962G and 7942G Cable Connections

1

DC adaptor port (DC48V) for phones not provided with inline power

6

Handset port

2

AC-to-DC power supply

7

Headset port

3

AC power cord

8

Footstand adjustment button

4

Network port (10/100 SW on the 7962G/7942G/7961G/7941G; 10/100/1000 SW on the 7961G-GE/7941G-GE) for connecting to the network

9

Auxiliary port (AUX)

5

Access port (10/100 PC on the 7962G/7942G/7961G/7941G; 10/100/1000 PC on the 7961G-GE/7941G-GE) for connecting your phone to your computer

   

Related Topics

Feature Key Capacity Increase for Cisco Unified IP Phones

Verifying the Phone Startup Process

Configuring Startup Network Settings

Configuring Security on the Cisco Unified IP Phones

Attaching a Cisco Unified IP Phone Expansion Module

The Cisco Unified IP Phone Expansion Module attaches to a Cisco Unified IP Phone 7962G, 7961G and 7961G-GE to extend the number or line appearances or programmable buttons on your phone. These phones support the Cisco Unified IP Phone Expansion Model 7914, 7915, and 7916. You can customize the button templates for the Cisco Unified IP Phone Expansion Module to determine the number of line appearances and speed dial buttons. See Modifying Phone Button Templates for details.


Note The Cisco Unified IP Phone 7941G, 7941G-GX, and 7942G do not support the Cisco Unified IP Phone Expansion Model 7914, 7915, and 7916.


You can attach one or more Cisco Unified IP Phone Expansion Modules 7914, 7915, or 7916 to the Cisco Unified IP Phone 7962G by using one of the following methods:

When you initially add the phone to Cisco Unified Communications Manager, by selecting 7914 14-Button Line Expansion Module for the Cisco Unified IP Phone Expansion 7914, 7915 12-Button Line Expansion Module or 7915 24-Button Line Expansion Module for the Cisco Unified IP Phone Expansion Module 7915, or 7916 12-Button Line Expansion Module or 7916 24-Button Line Expansion Module for the Cisco Unified IP Phone Expansion Module 7916 in the Module 1 or Module 2 fields, and choosing the appropriate expansion module firmware. See in the following procedure.

After the phone is configured in Cisco Unified Communications Manager.

You can attach a Cisco Unified IP Phone Expansion Module 7914 to the Cisco Unified IP Phone 7961G and 7961G-GE by using one of the following methods:

When you initially add the phone to Cisco Unified Communications Manager, you can choose 7914 14-Button Line Expansion Module in the Module 1 or Module 2 fields and then choose the appropriate expansion module firmware. See in the following procedure.

After the phone is configured in Cisco Unified Communications Manager.

To configure the Cisco Unified IP Phone Expansion Module on the Cisco Unified IP Phone, follow these steps.

Procedure


Step 1 Log in to Cisco Unified Communications Manager Administration.

Cisco Unified Communications Manager Administration window displays.

Step 2 From the menu, choose Device > Phone.

The Find and List Phone page appears. You can search for one or more phones that you want to configure for the Cisco Unified IP Phone Expansion Module.

Step 3 Select and enter your search criteria and click Find.

The Find and List Phone window displays showing a list of the phones that match your search criteria.

Step 4 Click the IP Phone that you want to configure for the Cisco Unified IP Phone Expansion Module.

The Phone Configuration window displays.

Step 5 Scroll to the Expansion Module Information section.

Step 6 To add support for one expansion module on Cisco Unified IP Phones 7961G and 7961G-GE, in the Module 1 field, select 7914 14-Button Line Expansion Module.

To add support for one expansion module on Cisco Unified IP Phone 7962G, in the Module 1 field, choose:

7914 14-Button Line Expansion Module for the Cisco Unified IP Phone Expansion Module 7914,

7915 12-Button Line Expansion Module or 7915 24-Button Line Expansion Module for the Cisco Unified IP Phone Expansion Module 7915, or

7916 12-Button Line Expansion Module or 7916 24-Button Line Expansion Module for the Cisco Unified IP Phone Expansion Module 7916.

Step 7 To add support for a second expansion module on Cisco Unified IP Phones 7961G and 7961G-GE, in the Module 2 field, choose 7914 14-Button Line Expansion Module.

To add support for a second expansion module on Cisco Unified IP Phone 7962G, in the Module 2 field, choose:

7914 14-Button Line Expansion Module for the Cisco Unified IP Phone Expansion Modules 7914,

7915 12-Button Line Expansion Module or 7915 24-Button Line Expansion Module for the Cisco Unified IP Phone Expansion Module 7915, or

7916 12-Button Line Expansion Module or 7916 24-Button Line Expansion Module for the Cisco Unified IP Phone Expansion Module 7916.


Note In the Firmware Load Information section, there are two fields that specify the firmware load for Modules 1 and 2. You can leave these fields blank to use the default firmware load.


Step 8 Click the Save icon.

A message displays asking you to click the Apply Config for the changes to take effect.

Step 9 Click OK.

Step 10 Click Apply Config.

The Apply Configuration Information dialog appears.

Step 11 Click OK.



Note Refer users to their Cisco Unified CM User Options web pages, so they can configure speed-dial buttons and program buttons to access phone services on the Cisco Unified IP Phone Expansion Module. See How Users Subscribe to Services and Configure Phone Features for more details.


Feature Key Capacity Increase for Cisco Unified IP Phones

The Cisco Unified IP Phone Expansion Modules 7915 and 7916 attach to your Cisco Unified IP Phone 7962G, adding up to 48 extra line appearances or programmable buttons to your phone. The line capability increase includes Directory Numbers (DN), line information menu, line ring menu, and line help ID.

You can configure all 48 additional keys on the Cisco Unified IP Phone Expansion Modules 7915 and 7916.

Cisco Unified IP Phones 7961G-GE and 7941G-GE do not support Cisco Unified IP Phone Expansion Modules 7915 and 7916.

Use the Phone Button Template Configuration to configure the buttons.

Cisco Unified Communications Manager includes several default phone button templates. When adding phones, you can assign one of these templates to the phones or create a new template.

To configure the 48 additional buttons, follow these steps:

Procedure


Step 1 From Cisco Unified Communications Manager Administration, choose Device > Device Settings > Phone Button Template.

Step 2 Click the Add New button.

Step 3 From the drop-down list, choose a template and click Copy.

Step 4 Rename the new template.

Step 5 Update the table to 54 Directory Numbers for Cisco Unified IP Phone 7962G.

See Cisco Unified Communications Manager Administration Guide and Cisco Unified Communications Manager System Guide for more information on creating and modifying templates.


Note You can also attach two Cisco Unified IP Phone Expansion Modules 7915s or two Cisco Unified IP Phone Expansion Modules 7916s, to provide 48 additional lines or speed-dial and feature buttons.



Related Topic

Configuring Softkey Templates

Adjusting the Placement of the Cisco Unified IP Phone

The Cisco Unified IP Phone includes an adjustable footstand. When placing the phone on a desktop surface, you can adjust the tilt height to several different angles in 7.5 degree increments from flat to 60 degrees. You can also mount these phones to the wall by using the footstand or by using the optional locking wall mount kit.

Adjusting Cisco Unified IP Phone Placement on the Desktop

You can adjust the footstand adjustment plate on the Cisco Unified IP Phone to the height that provides optimum viewing of the phone screen. See Figure 3-4 for more information.

Procedure


Step 1 Push in the footstand adjustment button.

Step 2 Adjust the footstand to desired height.


Securing the Phone with a Cable Lock

You can secure the Cisco Unified IP Phone to a desktop by using a laptop cable lock. The lock connects to the security slot on the back of the phone, and the cable can be secured to a desktop.

The security slot can accommodate a lock up to 20 mm. Compatible laptop cable locks include the Kensington® laptop cable lock and laptop cable locks from other manufacturers that can fit into the security slot on the back of the phone. See Figure 3-3.

Figure 3-3 Connecting a Cable Lock to the Cisco Unified IP Phone

Mounting the Phone to the Wall

You can mount the Cisco Unified IP Phone on the wall by using the footstand as a mounting bracket or you can use special brackets available in a Cisco Unified IP Phone wall mount kit. Wall mount kits must be ordered separately from the phone.

If you attach the Cisco Unified IP Phone to a wall by using the standard footstand and not the wall mount kit, you need to supply the following tools and parts:

Screwdriver

Screws to secure the Cisco Unified IP Phone to the wall

See Figure 3-4 for a graphical overview of the phone parts.

Before You Begin

To ensure that the handset attaches securely to a wall-mounted phone, remove the handset wall hook from the handset rest, rotate the hook 180 degrees, and reinsert the hook. Turning the hook exposes a lip on which the handset catches when the phone is vertical. For an illustrated procedure, see Installing the Wall Mount Kit for the Cisco Unified IP Phone at:

http://www.cisco.com/en/US/products/hw/phones/ps379/prod_installation_guides_list.html


Caution Use care not to damage wires or pipes located inside the wall when securing screws to wall studs.

Procedure


Step 1 Push in the footstand adjustment button.

Step 2 Adjust the footstand, so it is flat against the back of the phone.

Step 3 Insert two screws into a wall stud, matching them to the two screw holes on the back of the footstand.

The keyholes fit standard phone jack mounts.

Step 4 Hang the phone on the wall.


Figure 3-4 Parts Used in Wall Mounting the Cisco Unified IP Phone

1

Footstand adjustment button—Raises and lowers adjustment plate

2

Wall mounting screw holes

3

Adjustment plate—Raises and lowers phone vertically


Verifying the Phone Startup Process

After the Cisco Unified IP Phone has power connected to it, the phone begins its startup process by cycling through the following steps.

1. These buttons flash on and off in sequence:

Headset (only if the handset is off-hook when the phone powers up. Hang up the handset within 3 seconds to have the phone launch its secondary load. To continue with the primary load, leave the handset off-hook.)

Mute

Speaker

2. Some or all of the line keys flash amber in sequence.


Caution If the line keys flash red in sequence after flashing amber, do not power down the phone until the sequence of red flashes completes. This sequence can take several minutes to complete.

3. Some or all of the line keys flash green.

Normally, this sequence takes just a few seconds. However, if the phone's Flash memory is erased or the phone load is corrupted, the sequence of green flashes will continue while the phone begins a software update procedure. If the phone performs this procedure, the following buttons light to indicate progress:

Headset—Phone is waiting for the network and completing CDP and DHCP configuration. A DHCP server must be available in your network.

Mute—Phone is downloading images from the TFTP server.

Speaker—Phone is writing images to its Flash memory.

4. The phone screen displays the Cisco Systems, Inc., logo screen.

5. These messages appear as the phone starts:

Verifying Load (if the phone load does not match the load on the TFTP server). If this message appears, the phone starts up again and repeats step 1 through step 4 above.

Configuring IP

Updating the Trust List

Updating Locale

Configuring Unified CM List

Registering

6. The phone screen displays:

Current date and time

Primary directory number

Additional directory numbers and speed dial numbers, if configured

Softkeys

If the phone successfully passes through these stages, it has started up properly. If the phone does not start up properly, see Resolving Startup Problems.

Configuring Startup Network Settings

If you are not using DHCP in your network, you must configure these network settings on the Cisco Unified IP Phone after installing the phone on the network:

IP address

IP subnet information (subnet mask for IPv4 and subnet prefix length for IPv6)

Default gateway IP address

TFTP server IP address

You also may configure the domain name and the DNS server settings, if necessary.

Collect this information and see the instructions in Configuring Settings on the Cisco Unified IP Phones.

Configuring Security on the Cisco Unified IP Phones

The security features protect against several threats, including threats to the identity of the phone and to data. These features establish and maintain authenticated communication streams between the phone and the Cisco Unified Communications Manager server, and digitally sign files before they are delivered.

For more information about the security features, see Understanding Security Features for Cisco Unified IP Phones. Also, see Cisco Unified Communications Manager Security Guide.

You can initiate the installation of a Locally Significant Certificate (LSC) from the Security Configuration menu on the phone. This menu also lets you update or remove an LSC.

Before You Begin

Make sure that the appropriate Cisco Unified Communications Manager and the Certificate Authority Proxy Function (CAPF) security configurations are complete:

The CTL file or ITL file should have a CAPF certificate.

On Cisco Unified Communications Operating System Administration, verify that the CAPF certificate has been installed.

The CAPF is running and configured.

For more information, see Cisco Unified Communications Manager Security Guide.

To configure an LSC on the phone manually, perform these steps:

Procedure


Step 1 Obtain the CAPF authentication code that was set when the CAPF was configured.

Step 2 From the phone, choose Settings > Security Configuration.


Note You can control access to the Settings Menu by using the Settings Access field in the Cisco Unified Communications Manager Administration Phone Configuration window. For more information, see the Cisco Unified Communications Manager Administration Guide.


Step 3 Press **# to unlock settings on the Security Configuration menu. See Unlocking and Locking Options for information using locking and unlocking options.


Note If a Settings Menu password has been set up, SIP Phones present an "Enter password" prompt after you enter **#.


Step 4 Scroll to LSC and press the Update softkey.

The phone prompts for an authentication string.

Step 5 Enter the authentication code and press the Submit softkey.

The phone begins to install, update, or remove the LSC, depending on how the CAPF was configured. During the procedure, a series of messages appears in the LSC option field in the Security Configuration menu, so you can monitor progress. When the procedure completes successfully, the phone displays Installed or Not Installed.

The LSC install, update, or removal process can take a long time to complete. You can stop the process at any time by pressing the Stop softkey from the Security Configuration menu. (Settings must be unlocked before you can press this softkey.)

When the phone successfully completes the installation procedure, it displays "Success." If the phone displays "Failure," the authorization string may be incorrect or the phone may not be enabled for upgrading. See error messages generated on the CAPF server and take appropriate actions.

You can verify that an LSC is installed on the phone by choosing Settings >  Model Information and ensuring that the LSC setting shows Yes.


Related Topic

Understanding Security Features for Cisco Unified IP Phones