Cisco Unified IP Phone Administration Guide for Cisco Unified CallManager 5.0 (SCCP), Cisco IP Phone 7961G/7961G-GE and 7941G/7941G-GE
An Overview of the Cisco Unified IP Phone
Downloads: This chapterpdf (PDF - 917.0KB) The complete bookPDF (PDF - 3.31MB) | Feedback

An Overview of the Cisco Unified IP Phone

Table Of Contents

An Overview of the Cisco Unified IP Phone

Understanding the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE

What Networking Protocols are Used?

What Features are Supported on the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE?

Feature Overview

Configuring Telephony Features

Configuring Network Parameters Using the Cisco Unified IP Phone

Providing Users with Feature Information

Understanding Security Features for Cisco Unified IP Phones

Overview of Supported Security Features

Understanding Security Profiles

Identifying Encrypted and Authenticated Phone Calls

Security Restrictions

Overview of Configuring and Installing Cisco Unified IP Phones

Configuring Cisco Unified IP Phones in Cisco Unified CallManager

Checklist for Configuring the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE in Cisco Unified CallManager

Installing Cisco Unified IP Phones

Checklist for Installing the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE


An Overview of the Cisco Unified IP Phone


The Cisco Unified IP Phone 7961G and 7961G-GE (gigabit Ethernet version) and the 7941G and 7941G-GE (gigabit Ethernet version) are full-feature telephones that provide voice communication over an Internet Protocol (IP) network. The gigabit Ethernet Cisco Unified IP Phone 7961G-GE and 7941G-GE deliver the latest technology and advancements in Gigabit Ethernet VoIP telephony. The Cisco Unified IP Phone functions much like a digital business phone, allowing you to place and receive phone calls and to access features such as mute, hold, transfer, speed dial, call forward, and more. In addition, because the phone is connected to your data network, it offers enhanced IP telephony features, including access to network information and services, and customizeable features and services. The phone also supports security features that include file authentication, device authentication, signaling encryption, and media encryption.

A Cisco Unified IP Phone, like other network devices, must be configured and managed. These phones support G.711, G.729, G.729a, G.729b, G.729ab, and wideband (16bits, 16kHz) audio compression.

This chapter includes the following topics:

Understanding the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE

What Networking Protocols are Used?

What Features are Supported on the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE?

Understanding Security Features for Cisco Unified IP Phones

Overview of Configuring and Installing Cisco Unified IP Phones


Caution Using a cell, mobile, or GSM phone, or two-way radio in close proximity to a Cisco Unified IP Phone might cause interference. For more information, refer to the manufacturer's documentation of the interfering device.

Understanding the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE

Figure 1-1 shows the main components of the Cisco Unified IP Phone 7961G and 7961G-GE, and Figure 1-2 shows the main components of the Cisco Unified IP Phone 7941G and 7941G-GE.

Figure 1-1 Cisco Unified IP Phone 7961G and 7961G-GE

Figure 1-2 Cisco Unified IP Phone 7941G and 7941G-GE

1

Programmable buttons

Depending on configuration, programmable buttons provide access to:

Phone lines (line buttons)

Speed-dial numbers (speed-dial buttons, including the BLF speed-dial feature)

Web-based services (for example, a Personal Address Book (PAB) button)

Phone features (for example, a Privacy button)

The buttons illuminate to indicate status:

Green, steady—Active call

Green, flashing—Held call

Amber, steady—Privacy in use

Amber, flashing—Incoming call

Red steady—Remote line in use (shared line or BLF status)

2

Phone screen

Shows phone features.

3

Footstand button

Allows you to adjust the angle of the phone base.

4

Messages button

Auto-dials your voice message service (varies by service).

5

Directories button

Opens/closes the Directories menu. Use it to access call logs and directories.

6

Help button

Activates the Help menu.

7

Settings button

Opens/closes the Settings menu. Use it to control phone screen contrast and ring sounds.

8

Services button

Opens/closes the Services menu.

9

Volume button

Controls the handset, headset, and speakerphone volume (off-hook) and the ringer volume (on-hook).

10

Speaker button

Toggles the speakerphone on or off. When the speakerphone is on, the button is lit.

11

Mute button

Toggles the Mute feature on or off. When Mute is on, the button is lit.

12

Headset button

Toggles the headset on or off. When the headset is on, the button is lit.

13

Navigation button

Allows you to scroll through menus and highlight items. When the phone is on-hook, displays phone numbers from your Placed Calls log.

14

Keypad

Allows you to dial phone numbers, enter letters, and choose menu items.

15

Softkey buttons

Each activates a softkey option (displayed on your phone screen).

16

Handset light strip

Indicates an incoming call or new voice message.


What Networking Protocols are Used?

Cisco Unified IP Phones support several industry-standard and Cisco networking protocols required for voice communication. Table 1-1 provides an overview of the networking protocols that the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE support.

Table 1-1 Supported Networking Protocols on the Cisco Unified IP Phone 

Networking Protocol
Purpose
Usage Notes

Bootstrap Protocol (BootP)

BootP enables a network device such as the Cisco Unified IP Phone to discover certain startup information, such as its IP address.

If you are using BootP to assign IP addresses to the Cisco Unified IP Phone, the BOOTP Server option shows "Yes" in the network configuration settings on the phone.

Cisco Discovery Protocol (CDP)

CDP is a device-discovery protocol that runs on all Cisco-manufactured equipment.

Using CDP, a device can advertise its existence to other devices and receive information about other devices in the network.

The Cisco Unified IP Phone uses CDP to communicate information such as auxiliary VLAN ID, per port power management details, and Quality of Service (QoS) configuration information with the Cisco Catalyst switch.

Dynamic Host Configuration Protocol (DHCP)

DHCP dynamically allocates and assigns an IP address to network devices.

DHCP enables you to connect an IP phone into the network and have the phone become operational without you needing to manually assign an IP address or to configure additional network parameters.

DHCP is enabled by default. If disabled, you must manually configure the IP address, subnet mask, gateway, and a TFTP server on each phone locally.

Cisco recommends that you use DHCP custom option 150. With this method, you configure the TFTP server IP address as the option value. For additional supported DCHP configurations, refer to Cisco Unified CallManager System Guide.

Hypertext Transfer Protocol (HTTP)

HTTP is the standard way of transferring information and moving documents across the Internet and the web.

Cisco Unified IP Phones use HTTP for the XML services and for troubleshooting purposes.

Internet Protocol (IP)

IP is a messaging protocol that addresses and sends packets across the network.

To communicate using IP, network devices must have an assigned IP address, subnet, and gateway.

IP addresses, subnets, and gateways identifications are automatically assigned if you are using the Cisco Unified IP Phone with Dynamic Host Configuration Protocol (DHCP). If you are not using DHCP, you must manually assign these properties to each phone locally.

Real-Time Transport Protocol (RTP)

RTP is a standard protocol for transporting real-time data, such as interactive voice and video, over data networks.

Cisco Unified IP Phones use the RTP protocol to send and receive real-time voice traffic from other phones and gateways.

Skinny Client Control Protocol (SCCP)

SCCP includes a messaging set that allows communications between call control servers and endpoint clients such as IP Phones. SCCP is proprietary to Cisco Systems.

Cisco Unified IP Phones use SCCP for call control. You can configure the Cisco Unified IP Phone to use either SCCP or Session Initiation Protocol (SIP).

Session Initiation Protocol (SIP)

SIP is an emerging standard for setting up telephone calls, multimedia conferencing, and other types of communications on the Internet.

Cisco Unified IP Phones use SCCP for call control. You can configure the Cisco Unified IP Phone to use either SCCP or SIP.

Transmission Control Protocol (TCP)

TCP is a connection-oriented transport protocol.

Cisco Unified IP Phones use TCP to connect to Cisco Unified CallManager and to access XML services.

Transport Layer Security (TLS)

TLS is a standard protocol for securing and authenticating communications.

When security is implemented, Cisco Unified IP Phones use the TLS protocol when securely registering with Cisco Unified CallManager.

Trivial File Transfer Protocol (TFTP)

TFTP allows you to transfer files over the network.

On the Cisco Unified IP Phone, TFTP enables you to obtain a configuration file specific to the phone type.

TFTP requires a TFTP server in your network, which can be automatically identified from the DHCP server. If you want a phone to use a TFTP server other than the one specified by the DHCP server, you must manually assign the IP address of the TFTP server using the Network Configuration menu on the phone.

User Datagram Protocol (UDP)

UDP is a connectionless messaging protocol for delivery of data packets.

Cisco Unified IP Phones transmit and receive RTP streams, which utilize UDP.


Related Topics

Understanding Interactions with Other Cisco Unified IP Telephony Products, page 2-2

Understanding the Phone Startup Process, page 2-9

Network Configuration Menu, page 4-7

What Features are Supported on the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE?

The Cisco Unified IP Phone functions much like a digital business phone, allowing you to place and receive telephone calls. In addition to traditional telephony features, the Cisco Unified IP Phone includes features that enable you to administer and monitor the phone as a network device.

This section includes the following topics:

Feature Overview

Configuring Telephony Features

Configuring Network Parameters Using the Cisco Unified IP Phone

Providing Users with Feature Information

Feature Overview

Cisco Unified IP Phones provide traditional telephony functionality, such as call forwarding and transferring, redialing, speed dialing, conference calling, and voice messaging system access. Cisco Unified IP phones also provide a variety of other features. For an overview of the telephony features that the Cisco Unified IP Phone supports and for tips on configuring them, see the "Telephony Features Available for the Cisco Unified IP Phone" section on page 5-2.

As with other network devices, you must configure Cisco Unified IP Phones to prepare them to access Cisco Unified CallManager and the rest of the IP network. By using DHCP, you have fewer settings to configure on a phone, but if your network requires it, you can manually configure an IP address, TFTP server, and subnet mask. For instructions on configuring the network settings on the Cisco Unified IP Phones, see Chapter 4, "Configuring Settings on the Cisco Unified IP Phone."

The Cisco Unified IP Phone can interact with other services and devices on your IP network to provide enhanced functionality. For example, you can integrate the Cisco Unified IP Phones with the corporate Lightweight Directory Access Protocol 3 (LDAP3) standard directory to enable users to search for co-worker contact information directly from their IP phones. You can also use XML to enable users to access information such as weather, stocks, quote of the day, and other web-based information. For information about configuring such services, see the "Configuring Corporate Directories" section on page 5-16 and the "Setting Up Services" section on page 5-18.

Finally, because the Cisco Unified IP Phone is a network device, you can obtain detailed status information from it directly. This information can assist you with troubleshooting any problems users might encounter when using their IP phones. See Chapter 7, "Viewing Security Information, Model Information, Status, and Statistics on the Cisco Unified IP Phone," for more information.

Related Topics

Configuring Settings on the Cisco Unified IP Phone, page 4-1

Configuring Features, Templates, Services, and Users, page 5-1

Troubleshooting and Maintenance, page 9-1

Configuring Telephony Features

You can modify additional settings for the Cisco Unified IP Phone from the Cisco Unified CallManager Administration application. Use this web-based application to set up phone registration criteria and calling search spaces, to configure corporate directories and services, and to modify phone button templates, among other tasks. See the "Telephony Features Available for the Cisco Unified IP Phone" section on page 5-2 and the Cisco Unified CallManager documentation for additional information.

For more information about the Cisco Unified CallManager Administration application, refer to Cisco Unified CallManager documentation, including Cisco Unified CallManager Administration Guide. You can also use the context-sensitive help available within the application for guidance.

You can access the complete Cisco Unified CallManager documentation suite at this location:

http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/index.htm

Related Topic

Telephony Features Available for the Cisco Unified IP Phone, page 5-2

Configuring Network Parameters Using the Cisco Unified IP Phone

You can configure parameters such as DHCP, TFTP, and IP settings on the phone itself. You can also obtain statistics about a current call or firmware versions on the phone.

For more information about configuring features and viewing statistics from the phone, see Chapter 4, "Configuring Settings on the Cisco Unified IP Phone" and see Chapter 7, "Viewing Security Information, Model Information, Status, and Statistics on the Cisco Unified IP Phone."

Providing Users with Feature Information

If you are a system administrator, you are likely the primary source of information for Cisco Unified IP Phone users in your network or company. To ensure that you distribute the most current feature and procedural information, familiarize yourself with Cisco Unified IP Phone documentation. Make sure to visit the Cisco Unified IP Phone web site:

http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon/index.htm.

From this site, you can view various user guides.

In addition to providing documentation, it is important to inform users of available Cisco Unified IP Phone features—including those specific to your company or network—and of how to access and customize those features, if appropriate.

For a summary of some of the key information that phone users need their system administrators to provide, see Appendix A, "Providing Information to Users Via a Website."

Understanding Security Features for Cisco Unified IP Phones

Implementing security in the Cisco Unified CallManager system prevents identity theft of the phone and Cisco Unified CallManager server, prevents data tampering, and prevents call signaling and media stream tampering.

To alleviate these threats, the Cisco IP telephony network establishes and maintains authenticated and encrypted communication streams between a phone and the server, digitally signs files before they are transferred to a phone, and encrypts media streams and call signaling between Cisco Unified IP phones.

Table 1-2 shows where you can find additional information about security in this and other documents.

Table 1-2 Cisco Unified IP Phone and Cisco Unified CallManager Security Topics 

Topic
Reference

Detailed explanation of security, including set up, configuration, and troubleshooting information for Cisco Unified CallManager and Cisco Unified IP Phones

Refer to Cisco Unified CallManager Security Guide

Security features supported on the Cisco Unified IP Phone

See the "Overview of Supported Security Features" section

Restrictions regarding security features

See the "Security Restrictions" section

Viewing a security profile name

See the "Understanding Security Profiles" section

Identifying phone calls for which security is implemented

See the "Identifying Encrypted and Authenticated Phone Calls" section

TLS connection

See the "What Networking Protocols are Used?" section

See the "Adding Phones to the Cisco Unified CallManager Database" section on page 2-12

Security and the phone startup process

See the "Understanding the Phone Startup Process" section on page 2-9

Security and phone configuration files

See the "Adding Phones to the Cisco Unified CallManager Database" section on page 2-12

Changing the TFTP Server 1 or TFTP Server 2 option on the phone when security is implemented

See Table 4-2, in the "Network Configuration Menu" section on page 4-7

Understanding security icons in the CallManager 1 through CallManager 5 options in the Device Configuration Menu on the phone

See the "CallManager Configuration Menu" section on page 4-15

Items on the Security Configuration menu on the phone

See the "Security Configuration Menu" section on page 4-21

Items on the Security Configuration screen on the phone

See the "Security Configuration Menu" section on page 7-2

Unlocking the CTL file

See the "CTL File Menu" section on page 7-3

Disabling access to a phone's web pages

See the "Disabling and Enabling Web Page Access" section on page 8-3

Troubleshooting

See the "Troubleshooting Cisco Unified IP Phone Security" section on page 9-12

Refer to the Cisco Unified CallManager Security Guide

Deleting the CTL file from the phone

See the "Resetting or Restoring the Cisco Unified IP Phone" section on page 9-16

Resetting or restoring the phone

See the "Resetting or Restoring the Cisco Unified IP Phone" section on page 9-16


Overview of Supported Security Features

Table 1-3 provides an overview of the security features that the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE support. For more information about these features and about Cisco Unified CallManager and Cisco Unified IP Phone security, refer to Cisco Unified CallManager Security Guide.

For information about current security settings on a phone, choose Settings > Security Configuration. For more information, see the "Security Configuration Menu" section on page 7-2.


Note Most security features are available only if a certificate trust list (CTL) is installed on the phone. For more information about the CTL, refer to "Configuring the Cisco CTL Client" chapter in Cisco Unified CallManager Security Guide.


Table 1-3 Overview of Security Features 

Feature
Description

Image authentication

Signed binary files (with the extension .sbn) prevent tampering with the firmware image before it is loaded on a phone. Tampering with the image causes a phone to fail the authentication process and reject the new image.

Customer-site certificate installation

Each Cisco Unified IP Phone requires a unique certificate for device authentication. Phones include a manufacturing installed certificate (MIC), but for additional security, you can specify in Cisco Unified CallManager Administration that a certificate be installed by using the CAPF1 . Alternatively, you can install an LSC from the Security Configuration menu on the phone. See the "Configuring Security on the Cisco Unified IP Phone" section on page 3-19 for more information.

Device authentication

Occurs between the Cisco Unified CallManager server and the phone when each entity accepts the certificate of the other entity. Determines whether a secure connection between the phone and a Cisco Unified CallManager should occur, and, if necessary, creates a secure signaling path between the entities using TLS protocol. Cisco Unified CallManager will not register phones unless they can be authenticated by the Cisco Unified CallManager.

File authentication

Validates digitally-signed files that the phone downloads. The phone validates the signature to make sure that file tampering did not occur after the file creation. Files that fail authentication are not written to Flash memory on the phone. The phone rejects such files without further processing.

Signaling Authentication

Uses the TLS protocol to validate that no tampering has occurred to signaling packets during transmission.

Manufacturing installed certificate

Each Cisco Unified IP Phone contains a unique manufacturing installed certificate (MIC), which is used for device authentication. The MIC is a permanent unique proof of identity for the phone, and allows Cisco Unified CallManager to authenticate the phone.

Secure SRST reference

After you configure a SRST reference for security and then reset the dependent devices in Cisco Unified CallManager Administration, the TFTP server adds the SRST certificate to the phone cnf.xml file and sends the file to the phone. A secure phone then uses a TLS connection to interact with the SRST-enabled router.

Media encryption

Uses SRTP to ensure that the media streams between supported devices proves secure and that only the intended device receives and reads the data. Includes creating a media master key pair for the devices, delivering the keys to the devices, and securing the delivery of the keys while the keys are in transport.

Signaling encryption

Ensures that all SCCP signaling messages that are sent between the device and the Cisco Unified CallManager server are encrypted.

CAPF (Certificate Authority Proxy Function)

Implements parts of the certificate generation procedure that are too processing-intensive for the phone, and it interacts with the phone for key generation and certificate installation. The CAPF can be configured to request certificates from customer-specified certificate authorities on behalf of the phone, or it can be configured to generate certificates locally.

Security profiles

Defines whether the phone is nonsecure, authenticated, or encrypted. See the "Understanding Security Profiles" section for more information.

Encrypted configuration files

Lets you ensure the privacy of phone configuration files.

Optional disabling of the web server functionality for a phone

You can prevent access to a phone's web page, which displays a variety of operational statistics for the phone.

Phone hardening

Additional security options, which you control from Cisco Unified CallManager Administration:

Disabling PC port

Disabling Gratuitous ARP (GARP)

Disabling PC Voice VLAN access

Disabling access to the Setting menus, or providing restricted access that allows access to the User Preferences menu and saving volume changes only

Disabling access to web pages for a phone.

Note You can view current settings for the PC Port Disabled, GARP Enabled, and Voice VLAN enabled options by looking at the phone's Security Configuration menu. For more information, see the "Device Configuration Menu" section on page 4-15.

1 CAPF = Certificate Authority Proxy Function


Related Topics

Understanding Security Profiles

Identifying Encrypted and Authenticated Phone Calls

Security Restrictions

Device Configuration Menu, page 4-15

Understanding Security Profiles

All Cisco Unified IP Phones that support Cisco Unified CallManager 5.0 use a security profile, which defines whether the phone is nonsecure, authenticated, or encrypted. For information about configuring the security profile and applying the profile to the phone, refer to Cisco Unified CallManager Security Guide, Release 5.0(1).

To view the security mode that is set for the phone, look at the Security Mode setting in the Security Configuration menu. For more information, see the "Security Configuration Menu" section on page 4-21.

Related Topics

Identifying Encrypted and Authenticated Phone Calls

Security Restrictions

Device Configuration Menu, page 4-15

Identifying Encrypted and Authenticated Phone Calls

When security is implemented for a phone, you can identify authenticated or encrypted phone calls by icons on the screen on the phone.

In an authenticated call, all devices participating in the establishment of the call are authenticated by the Cisco Unified CallManager. When a call in progress is authenticated, the call progress icon to the right of the call duration timer in the phone LCD screen changes to this icon .

In an encrypted call, all devices participating in the establishment of the call are authenticated by the Cisco Unified CallManager. In addition, call signaling and media streams are encrypted. An encrypted call offers the highest level of security, providing integrity and privacy to the call. When a call in progress is being encrypted, the call progress icon to the right of the call duration timer in the phone LCD screen changes to the following icon: .


Note If the call is routed through non-IP call legs, for example, PSTN, the call may be nonsecure even though it is encrypted within the IP network and has a lock icon associated with it.


Related Topic

Understanding Security Profiles

Understanding Security Features for Cisco Unified IP Phones

Security Restrictions

Security Restrictions

A user cannot barge into an encrypted call if the phone that is used to barge is not configured for encryption. When barge fails in this case, a reorder tone (fast busy tone) plays on the phone on which the user initiated the barge.

If the initiator phone is configured for encryption, the barge initiator can barge into an authenticated or nonsecure call from the encrypted phone. After the barge occurs, Cisco Unified CallManager classifies the call as nonsecure.

If the initiator phone is configured for encryption, the barge initiator can barge into an encrypted call, and the phone indicates that the call is encrypted.

A user can barge into an authenticated call, even if the phone that is used to barge is nonsecure. The authentication icon continues to appear on the authenticated devices in the call, even if the initiator phone does not support security.

Overview of Configuring and Installing Cisco Unified IP Phones

When deploying a new IP telephony system, system administrators and network administrators must complete several initial configuration tasks to prepare the network for IP telephony service. For information and a checklist for setting up and configuring a complete Cisco IP telephony network, refer to the "System Configuration Overview" chapter in Cisco Unified CallManager System Guide.

After you have set up the IP telephony system and configured system-wide features in Cisco Unified CallManager, you can add IP phones to the system.

The following topics provide an overview of procedures for adding Cisco Unified IP Phones to your network:

Configuring Cisco Unified IP Phones in Cisco Unified CallManager

Installing Cisco Unified IP Phones

Configuring Cisco Unified IP Phones in Cisco Unified CallManager

To add phones to the Cisco Unified CallManager database, you can use:

Auto-registration

Cisco Unified CallManager Administration

Bulk Administration Tool (BAT)

BAT and the Tool for Auto-Registered Phones Support (TAPS)

For more information about these choices, see the "Adding Phones to the Cisco Unified CallManager Database" section on page 2-12.

For general information about configuring phones in Cisco Unified CallManager, refer to the "Cisco Unified IP Phone" chapter in Cisco Unified CallManager System Guide.

Checklist for Configuring the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE in Cisco Unified CallManager

Table 1-4 provides an overview and checklist of configuration tasks for the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE in Cisco Unified CallManager Administration. The list presents a suggested order to guide you through the phone configuration process. Some tasks are optional, depending on your system and user needs. For detailed procedures and information, refer to the sources in the list.

Table 1-4 Checklist for Configuring the Cisco Unified IP Phone 7961G/7961G-GE/7941G/7941G-GE in Cisco Unified CallManager 

Task
Purpose
For More Information

1. Gather the following information     about the phone:

Phone Model

MAC address

Physical location of the phone

Name or user ID of phone user

Device pool

Partition, calling search space, and location information

Number of lines and associated directory numbers (DNs) to assign to the phone

Cisco Unified CallManager user to associate with the phone

Phone usage information that affects phone button template, softkey template, phone features, IP Phone services, or phone applications

Provides list of configuration requirements for setting up phones.

Identifies preliminary configuration that you need to perform before configuring individual phones, such as phone button templates or softkey templates.

Refer to Cisco Unified CallManager System Guide,
"Cisco Unified IP Phone" chapter.

See the "Telephony Features Available for the Cisco Unified IP Phone" section on page 5-2.

2. Customize phone button templates     (if required).

Changes the number of line buttons, speed-dial buttons, Service URL buttons or adds a Privacy button to meet user needs.

Refer to Cisco Unified CallManager Administration Guide,
"Phone Button Template Configuration" chapter.

See the "Modifying Phone Button Templates" section on page 5-17.

3. Add and configure the phone by     completing these required fields in     the Phone Configuration window:

Phone type

Description (user name or ID)

MAC address

Device pool

Partition

Calling Search Space

Button template

Product Specific Configuration

Softkey template (if customized)

Adds the device with its default settings to the Cisco Unified CallManager database.

Refer to Cisco Unified CallManager Administration Guide, "Cisco Unified IP Phone Configuration" chapter.

For information about Product Specific Configuration fields, refer to "I" Button Help in the Phone Configuration window.

4. Add and configure directory     numbers (lines) on the phone by     completing these required fields in     the Directory Number Configuration     window.

Directory number(s)

Partition

Multiple Calls and Call Waiting

Call Forwarding and Pickup (if used)

Voice Messaging (if used)

Adds primary and secondary directory numbers and features associated with directory numbers to the phone.

Refer to Cisco Unified CallManager Administration Guide, "Cisco Unified IP Phone Configuration" chapter:
"Adding a Directory Number" section
"Creating a Cisco Unity Voice Mailbox" section.

See the "Telephony Features Available for the Cisco Unified IP Phone" section on page 5-2.

5. Customize softkey templates.

Adds, deletes, or changes order of softkey features that display on the user's phone to meet feature usage needs.

Refer to Cisco Unified CallManager Administration Guide,
"Softkey Template Configuration" chapter.

See the "Configuring Softkey Templates" section on page 5-18.

6. Configure speed-dial buttons and assign speed-dial numbers (optional).

Adds speed-dial buttons and numbers,

Note Users can change speed-dial settings on their phones by using Cisco Unified IP Phone User Options.

Refer to Cisco Unified CallManager Administration Guide, "Cisco Unified IP Phone Configuration" chapter,
"Configuring Speed-Dial Buttons" section.

7. Configure Cisco Unified IP Phone services and assign services (optional).

Provides IP Phone services.

Note Users can add or change services on their phones by using the Cisco Unified IP Phone User Options.

Refer to Cisco Unified CallManager Administration Guide, "Cisco Unified IP Phone Services Configuration" chapter.

See the "Setting Up Services" section on page 5-18.

8. Assign services to phone buttons     (optional).

Provides single button access to an IP phone service or URL.

Refer to Cisco Unified CallManager Administration Guide, "Cisco Unified IP Phone Configuration" chapter,
"Adding a Cisco Unified IP Phone Service to a Phone Button" section.

9. Add user information by configuring     required fields:

Name (last)

User ID

Password (for User Options web pages)

PIN (for use with Extension Mobility and Personal Directory)

Adds user information to the global directory for Cisco Unified CallManager.

Refer to Cisco Unified CallManager Administration Guide,
"Adding a New User" chapter.

See the "Adding Users to Cisco Unified CallManager" section on page 5-19.

10. Associate a user with a phone       (optional).

Provides users with control over their phone such as forwarding calls or adding speed-dial numbers or services.

Note Some phones, such as those in conference rooms, do not have an associated user.

Refer to Cisco Unified CallManager Administration Guide,
"Adding a New User" chapter, "Associating Devices to a User" section.


Installing Cisco Unified IP Phones

After you have added the phones to the Cisco Unified CallManager database, you can complete the phone installation. You (or the phone users) can install the phone at the users's location. The Cisco Unified IP Phone Installation Guide that ships in the box with each phone provides directions for connecting the phone handset, cables, and other accessories.


Note Before you install a phone, even if it is new, upgrade the phone to the current firmware image. For information about upgrading, refer to the Readme file for your phone, which is located at:

http://www.cisco.com/cgi-bin/tablebuild.pl/ip-7900ser


After the phone is connected to the network, the phone startup process begins and the phone registers with Cisco Unified CallManager. To finish installing the phone, configure the network settings on the phone depending on whether you enable or disable DHCP service.

If you used auto-registration, you need to update the specific configuration information for the phone such as associating the phone with a user, changing the button table, or directory number.

Checklist for Installing the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE

Table 1-5 provides an overview and checklist of installation tasks for the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE. The list presents a suggested order to guide you through the phone installation. Some tasks are optional, depending on your system and user needs. For detailed procedures and information, refer to the sources in the list.

Table 1-5 Checklist for Installing the Cisco Unified IP Phone 7961G/7961G-GE/7941G/7941G-GE 

Task
Purpose
For More Information

1. Choose the power source for the phone:

Power over Ethernet (PoE)

External power supply

Determines how the phone receives power.

See the "Providing Power to the Cisco Unified IP Phone" section on page 2-5.

2. Assemble the phone, adjust phone     placement, and connect the network     cable.

Locates and installs the phone in the network.

See the "Installing the Cisco Unified IP Phone" section on page 3-9.

See the "Adjusting the Placement of the Cisco Unified IP Phone" section on page 3-14.

3. Add a Cisco Unified IP Phone Expansion Module 7914 to the Cisco Unified IP Phone 7961G/7961G-GE (optional).

Extends functionality of a Cisco Unified IP Phone 7961G/7961G-GE by adding 14 line appearances or speed dial numbers.

See the "Attaching the Cisco Unified IP Phone Expansion Module 7914" section on page 3-12.

4. Monitor the phone startup process.

Verifies that phone is configured properly.

See the "Verifying the Phone Startup Process" section on page 3-17.

5. Configure these network settings on     the phone by choosing Settings >     Network Configuration.

To enable DHCP:

Set DHCP Enabled to Yes

To use an alternate TFTP server, set Alternate TFTP Server to Yes
Enter IP address for TFTP Server 1

To disable DHCP:

Set DHCP Enabled to No

Enter static IP address for phone

Enter subnet mask

Enter default router IP addresses

Enter domain name where phone resides

Set Alternate TFTP Server to Yes
Enter IP address for TFTP Server 1

Using DHCP—The IP address is automatically assigned and the Cisco Unified IP Phone is directed to a TFTP Server.

Note Consult with the network administrator if you need to assign an alternative TFTP server instead of using the TFTP server assigned by DHCP.

Without DHCP—You must configure the IP address, TFTP server, subnet mask, domain name, and default router locally on the phone.

See the "Configuring Startup Network Settings" section on page 3-19.

See the "Network Configuration Menu" section on page 4-7.

6. Set up security on the phone.

Provides protection against data tampering threats and identity theft of phones.

See the "Configuring Security on the Cisco Unified IP Phone" section on page 3-19.

7. Make calls with the Cisco Unified IP Phone.

Verifies that the phone and features work correctly.

Refer to Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE Phone Guide.

8. Provide information to end users about     how to use their phones and how to     configure their phone options.

Ensures that users have adequate information to successfully use their Cisco Unified IP Phones.

See Appendix A, "Providing Information to Users Via a Website."