Cisco Unified IP Phone Administration Guide for Cisco Unified CallManager 5.0 (SIP), Cisco IP Phone 7905G/7912G
Configuring Settings on the Cisco Unified IP Phone
Downloads: This chapterpdf (PDF - 263.0KB) The complete bookPDF (PDF - 2.25MB) | Feedback

Configuring Settings on the Cisco Unified IP Phone

Table Of Contents

Configuring Settings on the Cisco Unified IP Phone

Accessing Network Configuration Settings through the Network Configuration Menu on the Phone

Displaying the Network Configuration Menu

Unlocking and Locking Options on the Network Configuration Menu

Editing Settings in the Network Configuration Menu

Verifying Network Settings

Configuring IP Settings

Configuring the Encryption Key

Configuring Encryption Key Using LCD screen on the Phone

Configuring Encryption Key Using Phone Configuration Web Page

Network Configuration Menu Parameter Descriptions

SIP Configuration Menu Parameter Descriptions

Viewing Network Settings through a Phone Configuration Web Page


Configuring Settings on the Cisco Unified IP Phone


The Cisco Unified IP Phone includes various configurable network and SIP settings that you may need to modify before the phone is functional for your users.

The following sections provide details about configuring and verifying these network settings:

Accessing Network Configuration Settings through the Network Configuration Menu on the Phone

Verifying Network Settings

Configuring IP Settings

Configuring the Encryption Key

Network Configuration Menu Parameter Descriptions

SIP Configuration Menu Parameter Descriptions

Viewing Network Settings through a Phone Configuration Web Page

Accessing Network Configuration Settings through the Network Configuration Menu on the Phone

You can view and set most network configuration parameters for the Cisco Unified IP Phone 7905G and 7912G using the Network Configuration menu on the phone.

For a description of the parameters that appear on the Network Configuration menu, see Table 4-1.

This section includes the following topics:

Displaying the Network Configuration Menu

Unlocking and Locking Options on the Network Configuration Menu

Editing Settings in the Network Configuration Menu

Displaying the Network Configuration Menu

To display the Network Configuration menu on a Cisco Unified IP Phone 7905G or 7912G, follow these steps:

Procedure


Step 1 Press the Menu button.

Step 2 Choose Settings > Network Configuration.


To exit the Network Configuration menu, take one of these actions:

Press the Back softkey to return to the Settings menu.

Press the Menu button to return to the main screen.

Related Topics

Unlocking and Locking Options on the Network Configuration Menu

Editing Settings in the Network Configuration Menu

Unlocking and Locking Options on the Network Configuration Menu

Configuration options (or parameters) in the Network Configuration menu are locked by default to prevent users from making changes that could affect the operation of a phone. You must unlock these options before you can change them.

When options are inaccessible for modification, a locked padlock icon appears on the Network Configuration screen. When options are unlocked and accessible for modification, an unlocked padlock icon appears on this menu, as shown below. This unlocked padlock icon appears in the margins of this chapter to indicate procedures that require you to unlock settings before modifying them.

If a password has been specified for the phone, you must enter the password when unlocking network configuration options.

To unlock network settings on the Cisco Unified IP Phone 7905G and 7912G, perform the following steps. Network settings are locked again automatically when you return to the main screen.

Procedure


Step 1 Press the Menu button.

Step 2 Choose Settings > Network Configuration.

Step 3 From the Network Configuration menu, press **#.

Step 4 If the phone displays "Enter Admin Password," enter your password and then press the Accept softkey.

For information about entering a password, see the "Editing Settings in the Network Configuration Menu" section.

Step 5 Look at the icon in the upper-right portion of the LCD.

When options are locked, the icon appears as a locked padlock.

When options are unlocked, the icon appears as an unlocked padlock.


Related Topics

Displaying the Network Configuration Menu

Editing Settings in the Network Configuration Menu

Editing Settings in the Network Configuration Menu

When you edit the value of an parameter on the Network Configuration menu, follow these guidelines:

Use the keys on the telephone keypad to enter numbers and letters.

To enter letters using the keypad, use a corresponding number key. Press the key one or more times to display a particular letter. For example, press the 2 key once for "a," twice quickly for "b," and three times quickly for "c." After you pause, the cursor automatically advances to allow you to enter the next letter.

If an parameter can accept either numbers or letters, the Number or Alpha softkey will appear. Press the Number softkey to enter numbers. Press the Alpha softkey to enter letters.

To enter a period (for example, in an IP address), press the * (asterisk) key.

To correct a mistake, press the << softkey to delete the character to the left of the cursor.

Press the Cancel softkey before pressing the Validate softkey or the Save softkey to discard any changes you have made.

Related Topics

Displaying the Network Configuration Menu

Unlocking and Locking Options on the Network Configuration Menu

Verifying Network Settings

On Cisco Unified IP Phone 7905G and 7912G, you can view detailed information about the current network settings of the phone. Use this information to troubleshoot or to make modifications.

To display current network settings for the Cisco Unified IP Phone by using the Phone Configuration web page, follow these steps:

Procedure


Step 1 Display the Phone Configuration web page.

For instructions, see the "Viewing Network Settings through a Phone Configuration Web Page" section.

Step 2 In the pane on the left:

a. Select Network Configuration to review network configuration information.

b. Select Network Statistics to view network statistics.


To display current network settings for the Cisco Unified IP Phone by using the buttons on the phone, follow these steps:

Procedure


Step 1 Display the Network Configuration menu.

For instructions, see the "Displaying the Network Configuration Menu" section.

Step 2 Scroll through the parameters to display the settings described in Table 4-1.


Configuring IP Settings

Use these guidelines when manually configuring the IP settings:

You can use 0.0.0.0 for the subnet mask only if the default gateway is also 0.0.0.0.

Ensure the TFTP server has an IP address.

Ensure the default gateway IP address is on the same subnet as the host IP address.


Note Procedures involved in configuring IP settings or TFTP parameters cannot be completed when DHCP is enabled in your network.


Configuring the Encryption Key

Cisco Unified Call Manager can operate in secure or non-secure mode. When operating in secure mode, Cisco Unified Call Manager generates encrypted configuration files that can be decrypted only with the same encryption key.

If you are operating your phone in a secure environment, you must manually configure the encryption key that the phone will use to decrypt the configuration file downloaded from Cisco Unified Call Manager. You may configure the encryption key by using either the LCD screen on the phone or by using the Phone Configuration Web page.

The instructions in the following encryption-related sections assume a network environment in which a DHCP server provides the applicable TFTP IP address, and the Cisco Unified IP Phone has been pre-configured on the Cisco Unified CallManager to run SIP.

This section contains the following topics:

Configuring Encryption Key Using LCD screen on the Phone

Configuring Encryption Key Using Phone Configuration Web Page

Configuring Encryption Key Using LCD screen on the Phone

Procedure


Step 1 Connect your Cisco Unified IP Phone to the network.

Your Cisco Unified IP Phone should upgrade automatically to a SIP image.

Step 2 Press the MENU key on your phone.

Step 3 Go to Settings > Network Configuration > Profile EncryptKeyEx

Step 4 Press **# to unlock the menu.

You may be prompted to enter a password to unlock the menu. Enter cisco and press Accept.

Step 5 Press Edit.

Step 6 Use the keypad to enter an encryption key.

Step 7 Press Validate when finished.

Step 8 Press Save to save all values.

Step 9 Press MENU to exit the configuration menu.

Step 10 Reboot the Cisco Unified IP Phone.

The phone contacts the TFTP server and download its configuration file. When the idle screen is displayed along with a telephone number, the phone is ready for use.


Configuring Encryption Key Using Phone Configuration Web Page

Procedure


Step 1 Connect your Cisco Unified IP Phone to the network.

Your Cisco Unified IP phone should upgrade automatically to a SIP image.

Step 2 Determine the IP address of the phone:

a. Press the MENU key

b. Go to Settings > Network Configuration > IP Address, and make a note of the IP address because you will need to enter this address later.

Step 3 Start two instances of a web browser.

You will use one browser to access the Phone Configuration Web Page and the other browser to access the Cisco Unified CallManager Administration pages.

Step 4 Do the following to access the Phone Configuration Web Page:

a. Enter the URL:

http://PHONE_IP_ADDRESS/dev

b. Enter cisco in the UIPassword field if prompted.

c. Click Apply.

The Network Parameters page (which is one of the Phone Configuration Web pages) displays.

Step 5 Do the following to access the Cisco Unified CallManager Administration pages.

a. Enter the following URL:
http://<CALL_MANAGER_IP_ADDRESS>

b. Click on Cisco Unified CallManager Administration link.

If you are prompted to accept or cancel a security certificate, you must accept the certificate to continue.

c. Enter the User Name and Password to access Cisco Unified CallManager.

The Cisco Unified CallManager Administration main page displays.

d. Click on Device > Phone.

e. Click the Find button to display a list of devices.

f. Click on the device name corresponding to your Cisco Unified IP phone.

Cisco Unified Call Manager displays the Phone Configuration Administration page.

g. Scroll down to the Symmetric Key Information box for the phone.

Step 6 Copy the Symmetric Key value (if this value is not already present, click the Generate String button) from the Cisco Unified CallManager Phone Configuration Administration page and paste it into the EncryptKeyEx field on the Cisco Unified IP Phone Network Parameters page.

Step 7 Click Apply on the Phone Configuration Web Page to save the values.

The phone will automatically reboot and request its encrypted configuration file from the TFTP server. When the idle screen is displayed along with a telephone number, the phone is ready for use.


Network Configuration Menu Parameter Descriptions

Table 4-1 describes all network configuration parameters that exist in the Network Configuration menu of the Cisco Unified IP Phone 7905G/7912G.

Table 4-1 Network Configuration Menu Parameters  

Parameter
Description
To Change

DHCP Server

IP address of the Dynamic Host Configuration Protocol (DHCP) server from which the phone obtains information such as its IP address, its subnet mask, and the IP addresses of the network gateway and the DNS, NTP, and TFTP servers.

Display only—cannot configure.

MAC Address

Unique Media Access Control (MAC) address of the phone.

Display only—cannot configure.

Host Name

Unique host name of the phone.

Display only—cannot configure.

Domain Name (not applicable when used with Cisco Unified CallManager)

Network domain in which the phone resides. You can change this value if the Alternate Domain parameter is set to Yes.

1. Unlock configuration parameters.

2. Set the Alternate Domain parameter to Yes.

3. Scroll to the Domain Name parameter, press the Edit softkey, and then enter a new domain name.

4. Press the Validate softkey, and then press the Save softkey.

IP Address

Internet Protocol (IP) address of the phone. You can use this parameter to assign the IP address if DHCP does not provide it.

If you assign an IP address with this parameter, you must also assign a subnet mask and network gateway (default router). See the Subnet Mask and the Default Router parameters in this table.

1. Unlock configuration parameters.

2. Set the DHCP Enabled parameter to No.

3. Scroll to the IP Address parameter, press the Edit softkey, and then enter a new IP Address.

4. Press the Validate softkey, and then press the Save softkey.

Subnet Mask

Subnet mask used by the phone. You can use this parameter to assign a subnet mask if DHCP does not provide it.

If you assign a Subnet Mask with this parameter, you must also assign an IP address and a network gateway (default router) for the phone. See the IP Address and the Default Router parameters in this table.

1. Unlock configuration parameters.

2. Set the DHCP Enabled parameter to No.

3. Scroll to the Subnet Mask parameter, press the Edit softkey, and then enter a new subnet mask.

4. Press the Validate softkey, and then press the Save softkey.

TFTP Server1 (This parameter is shown as TFTP Server 1 when the phone is configured to operate in a standard Cisco Unified CallManager environment; in a standard SIP environment the parameter is TFTP Server.)

IP address or URL of the TFTP server from which a phone obtains a profile. Required if the DHCP server does not provide the TFTP server address.

If you set the Alternate TFTP parameter to Yes, you must enter a non-zero value for the TFTP Server1 parameter.

1. Unlock configuration parameters.

2. Set the TFTP Enabled parameter to Yes.

3. Set the Alternate TFTP parameter to Yes.

4. Scroll to the TFTP1 Server parameter, press the Edit softkey, and then enter a new TFTP server IP address or URL.

5. Press the Validate softkey, and then press the Save softkey.

TFTP Server 2

This parameter is read-only and the value displayed, if any, is the backup TFTP server specified in DHCP Parameter 150.

Display only—cannot configure.

Default Router

IP address of the network gateway used by the phone. You can use this parameter to assign this address if DHCP does not provide it.

If you assign a network gateway address with this parameter, you must also assign an IP address and a subnet mask for the phone. See the IP Address and the Subnet Mask parameters in this table.

1. Unlock configuration parameters.

2. Set the DHCP Enabled parameter to No.

3. Scroll to the Default Router parameter, press the Edit softkey, and then enter a new network gateway IP address.

4. Press the Validate softkey, and then press the Save softkey.

DNS Server 1,
DNS Server 2

IP addresses of the Primary Domain Name System (DNS) server (DNS Server 1) and secondary DNS server (DNS Server 2) used by the phone.

1. Unlock configuration parameters.

2. Set the Alternate DNS parameter to Yes.

3. Scroll to the DNS Server 1 parameter or the DNS Server 2 parameter, press the Edit softkey, and then enter a new DNS server IP address.

4. Press the Validate softkey, and then press the Save softkey.

NTP Server 1,
NTP Server 2 (not applicable when used with Cisco Unified CallManager)

IP addresses of the Primary Network Time Protocol (NTP) server (NTP Server 1) and secondary NTP server (NTP Server 2) used by the phone.

1. Unlock configuration parameters.

2. Set the Alternate NTP parameter to Yes.

3. Scroll to the NTP Server 1 parameter or the NTP Server 2 parameter, press the Edit softkey, and then enter a new NTP server IP address.

4. Press the Validate softkey, and then press the Save softkey.

Time Zone (not applicable when used with Cisco Unified CallManager)

Offset to apply to the Greenwich Mean Time (GMT) returned by an NTP server to determine local time (to use for the screen display, for example).

Local time is generated as follows:

Local time =
GMT + Time Zone,
if Time Zone <= 12.

Local time =
GMT + Time Zone - 25,
if Time Zone > 12.

For example, Time Zone = 17 for Pacific Standard Time.

Note You must update this parameter manually when daylight savings time goes into effect and ends.

1. Unlock configuration parameters.

2. Scroll to the Time Zone parameter, press the Edit softkey, and then enter a new time zone offset value.

3. Press the Validate softkey, and then press the Save softkey.

Operational VLAN ID

Auxiliary Virtual Local Area Network (VLAN) configured on a Cisco Catalyst switch in which the phone is a member.

If the phone has not received an auxiliary VLAN, this parameter indicates the Administrative VLAN.

If neither the auxiliary VLAN nor the Administrative VLAN are configured, this parameter is blank.

The phone obtains its Operational VLAN ID via Cisco Discovery Protocol (CDP) from the switch to which the phone is attached. To assign a VLAN ID manually, use the Admin VLAN ID parameter.

Admin. VLAN ID

Auxiliary VLAN in which the phone is a member.

Overrides the value specified by the Operation VLAN ID parameter.

1. Unlock configuration parameters.

2. Scroll to the Admin. VLAN ID parameter, press the Edit softkey, and then enter a new Admin VLAN value.

3. Press the Validate softkey, and then press the Save softkey.

VLAN Enabled

Indicates whether VLAN is enabled for the phone.

1. Unlock configuration parameters.

2. Scroll to the VLAN Enabled parameter and press the No softkey to disable VLAN, or press the Yes softkey to enable VLAN.

3. Press the Save softkey.

CDP Enabled

Indicates whether Cisco Discovery Protocol (CDP) is enabled for the phone. CDP allows the phone to be discovered by the CiscoWorks network management system.

For more information about CiscoWorks2000, refer to the documentation available at this URL:

http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cw2000/index.htm

1. Unlock configuration parameters.

2. Scroll to the CDP Enabled parameter and press the No softkey to disable CDP, or press the Yes softkey to enable CDP.

3. Press the Save softkey.

DHCP Enabled (enabled by default)

Specifies whether to use the DHCP server to obtain information such as its IP address, its subnet mask, and the IP addresses of the network gateway and the DNS, NTP, and TFTP servers.

If this parameter is 0, you must manually specify the IP address of the phone, and the subnet mask and the network gateway (default router) used by the phone.

1. Unlock configuration parameters.

2. Scroll to the DHCP Enabled parameter and press the No softkey to disable DHCP, or press the Yes softkey to enable DHCP.

3. Press the Save softkey.

TFTP Enabled

Enables or disables downloading of a profile from a TFTP server. If you set this parameter to Yes and subsequently make changes using the web interface, you must set this parameter to No before saving those changes; otherwise, the changes will be overwritten by the profile obtained from a TFTP server.

If you set this parameter to Yes and do not specify a TFTP server, the phone will use the TFTP IP address or URL obtained from the DHCP server to contact the TFTP server. If you set this parameter to Yes, set the Alternate TFTP parameter to Yes, and specify a value for the TFTP Server parameter, the phone will use the server that you specify.

1. Unlock configuration parameters.

2. Scroll to the TFTP Enabled parameter and press the No softkey to disable TFTP, or press the Yes softkey to enable TFTP.

3. Press the Save softkey.

Alternate TFTP

Indicates whether the phone obtains the IP address or URL of the TFTP server from the DHCP server (No) or uses the IP address or URL specified by the TFTP Server parameter (Yes).

If you set the Alternate TFTP server to Yes, you must specify a value for the TFTP Server parameter.

1. Unlock configuration parameters.

2. Scroll to the Alternate TFTP parameter and press the Yes softkey if the phone should use an alternative TFTP server. Press the No softkey otherwise.

3. Press the Save softkey.

Alternate DNS

Indicates whether the phone obtains the IP address of the DNS server from the DHCP server (No) or uses the IP addresses specified by the DNS Server 1 and, optionally, the DNS Server 2 parameters (Yes).

If you set the Alternate DNS server to Yes, you must specify a value for the DNS Server 1 parameter. You may also specify a value for the DNS Server 2 parameter.

1. Unlock configuration parameters.

2. Scroll to the Alternate DNS parameter and press the Yes softkey if the phone should use an alternative DNS. Press the No softkey otherwise.

3. Press the Save softkey.

Alternate NTP (not applicable in a Cisco Unified CallManager environment)

Indicates whether the phone obtains the IP address of the NTP server from the DHCP server (No) or uses the IP addresses specified by the NTP Server 1 and, optionally, the NTP Server 2 parameters (Yes).

If you set the Alternate NTP server to Yes, you must specify a value for the NTP Server 1 parameter. You may also specify a value for the NTP Server 2 parameter.

1. Unlock configuration parameters.

2. Scroll to the Alternate NTP parameter and press the Yes softkey if the phone should use an alternative NTP server. Press the No softkey otherwise.

3. Press the Save softkey.

Alternate Domain

Indicates whether the phone is using an alternative domain name.

If you set this parameter to Yes, you must specify a value for the Domain Name parameter.

1. Unlock configuration parameters.

2. Scroll to the Alternate Domain parameter and press the Yes softkey if the phone should use an alternative domain name. Press the No softkey otherwise.

3. Press the Save softkey.

Symmetric Key (This parameter is shown as Symmetric Key when the phone is configured to operate in a standard Cisco Unified CallManager environment; in a standard SIP environment the parameter is Profile Encrypt Key Ex.)

Specifies an encryption key used to decrypt the profile that the phone downloads from the TFTP server.

1. Unlock configuration parameters.

2. Scroll to the Symmetric Key parameter, press the Edit softkey, and then enter a new encryption key.

3. Press the Validate softkey, and then press the Save softkey.

Erase Configuration

Changes these settings to their default values: Network Configuration menu settings (including password), SIP Configuration menu settings, Call Preferences menu settings, volume settings, and contrast settings.

1. Unlock configuration parameters.

2. Scroll to the Erase Configuration parameter, press the Yes softkey, and then press the Save softkey.


Related Topics

Verifying Network Settings

Configuring IP Settings

SIP Configuration Menu Parameter Descriptions

Table 4-2 describes SIP configuration parameters. To access the SIP Configuration menu, choose SIP Configuration from the Settings menu.


Note The Edit, Yes, or No softkeys for changing SIP configuration parameters appear only if options are unlocked as described in the "Unlocking and Locking Options on the Network Configuration Menu" section. For information about the keys you can use to edit parameters, see the "Editing Settings in the Network Configuration Menu" section.


Table 4-2 SIP Configuration Menu Parameters 

Parameter
Description
To Change

SIP Proxy 1

SIP Proxy 2

SIP Proxy 3

SIP Proxy 4

SIP Proxy 1 and SIP Proxy 2 accept either the IP address or URL of the SIP proxy server used by the phone.

SIP Proxy 3 and SIP Proxy 4 accept only the IP address used by the phone.

1. Unlock configuration parameters.

2. Scroll to the SIP Proxy parameter, press the Edit softkey, and then enter the IP address or URL of a SIP proxy server.

3. Press the Accept softkey, and then press the Save softkey.

User ID

User ID for registration and authentication of the phone.

1. Unlock configuration parameters.

2. Scroll to the User ID parameter, press the Edit softkey, and then enter a user ID.

3. Press the Accept softkey, and then press the Save softkey.

Password

Password for authentication of the phone.

1. Unlock configuration parameters.

2. Scroll to the Password parameter, press the Edit softkey, and then enter a Password.

3. Press the Accept softkey, and then press the Save softkey.

Use Login ID

Indicates whether to use the value specified with the Login ID parameter instead of the value specified with the User ID parameter for authentication of the phone.

1. Unlock configuration parameters.

2. Scroll to the Use Login ID parameter, and then press the Yes softkey to use the value specified with the Login ID parameter for authentication.

3. Press the Save softkey.

Login ID

Alternate ID used for authentication of the phone.

1. Unlock configuration parameters.

2. Set the Use Login ID parameter to Yes.

3. Scroll to the Login ID parameter, press the Edit softkey, and then enter a login ID.

4. Press the Accept softkey, and then press the Save softkey.

Local SIP Port

Port where the phone listens for incoming requests and sends outgoing requests.

1. Unlock configuration parameters.

2. Scroll to the Local SIP Port parameter, press the Edit softkey, and then enter a SIP port from 5060 to 65535.

3. Press the Accept softkey, and then press the Save softkey.

Local RTP Port

Port from which the phone transmits and receives media streams.

1. Unlock configuration parameters.

2. Scroll to the Local RTP Port parameter, press the Edit softkey, and then enter a SIP port, which must be an even number from 0 to 65535.

3. Press the Accept softkey, and then press the Save softkey.

Backup Proxy Timeout (not displayed in Cisco Unified CallManager environment).

Timeout, in seconds, for switching from backup proxy server to primary proxy server.

The value can range from 0 to 4294967295.

1. Unlock configuration parameters.

2. Scroll to the Backup Proxy Timeout parameter, press the Edit softkey, and then enter a timeout value.

3. Press the Accept softkey, and then press the Save softkey.

Outbound Proxy (not displayed in Cisco Unified CallManager environment).

IP address or URL of the SIP outbound proxy server used by the phone.

1. Unlock configuration parameters.

2. Scroll to the Outbound Proxy parameter, press the Edit softkey, and then enter the IP address or URL of the outbound proxy server.

3. Press the Accept softkey, and then press the Save softkey.

Register Expires

SIP registration interval, in seconds, between each registration renewal to the SIP proxy server.

The value can range from 1 to 86400.

1. Unlock configuration parameters.

2. Scroll to the Register Expires parameter, press the Edit softkey, and then enter the SIP registration interval.

3. Press the Accept softkey, and then press the Save softkey.

Register with Proxy

Indicates whether to enable SIP registration. This parameter is ignored if a SIP proxy server is not specified.

1. Unlock configuration parameters.

2. Scroll to the Register with Proxy and press the Yes softkey to enable SIP registration, or press the No softkey to disable SIP registration.

3. Press the Save softkey.

NAT WAN IP Address (not displayed in Cisco Unified CallManager environment).

External Network Address Translation (NAT) IP address where other SIP user agents can communicate with the phone.

1. Unlock configuration parameters.

2. Scroll to the NAT WAN IP Address parameter, press the Edit softkey, and then enter the NAT IP address.

3. Press the Accept softkey, and then press the Save softkey.


Viewing Network Settings through a Phone Configuration Web Page

You can view (but not set) network configuration parameters for a Cisco Unified IP Phone 7905G and 7912G from the Phone Configuration Web Page.

To access the Phone Configuration Web Page for a phone, follow these steps:

Procedure


Step 1 Open a web browser and enter the following URL, where IPaddress is the IP address of your phone:

Step 2 http://IPaddress

On the Cisco Unified IP Phone  7905G and 7912G, you can determine the IP address by pressing the Menu button, choosing Settings > Network Configuration, and then scrolling to IP Address.

For example, the Phone Configuration Web Page for a Cisco Unified IP Phone with the IP address 192.168.3.225 is http://192.168.3.225

Step 3 Press Enter.

The Phone Configuration Web Page appears.


For a complete list of parameters and descriptions of each parameter, see "Reference List of Parameters."